Technical Manual Beltone Turn ITE -...
Transcript of Technical Manual Beltone Turn ITE -...
Technical ManualBeltone Turn ITE
Global Technical Operationsgto.gnresound.com
Lautrupbjerg 7 • DK-2750 Ballerup • DenmarkE-Mail: [email protected]
Doc. No. 0175860 rev. F
Page 2 of 17
Table of contents
Subject Page
Matrix ............................................................................................................. 3 Spare Part List ............................................................................................... 4 Faceplate Assemblies .................................................................................... 5 Blank Faceplates............................................................................................ 6 Hybrid Connections ........................................................................................ 7 Diagram....................................................................................................... 8-9 Receiver assembly ....................................................................................... 10 Prepare the faceplate ............................................................................ 11-13 Options ......................................................................................................... 14 Final Device ................................................................................................. 15 Service tool .................................................................................................. 16 Test Equipment ............................................................................................ 17
Doc. No. 0175860 rev. F
Page 3 of 17
Matrix
C3.1 Battery Size 13
Normal Power Single Mic
VC (floating)
L-TRIMMER P-TRIMMER H-TRIMMER Push Button Telecoil
TN45-P x x x Standard Optional Optional Optional Optional Optional
TN3T45-P x x x Standard Standard Standard Standard Optional Optional
Note: • All ITE faceplate assemblies can be fitted with three trimmers or less.• If a trimmer, PB and telecoil are opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the TURN Configuration Tool Software to reflect correct option added / removed.• The Turn configuration software can be downloaded from the GTO website: http://gto.gnresound.com
Doc. No. 0175860 rev. F
Page 4 of 17
Spare Part list
Item Part No.Tubing,Q-flex,.100”ID X.120”OD 10038801Tape, 3m., Doubleface (56X3.9MM) 10038905Wrap for BK1610 receiver 15414300Flex-Hybrid, C3.1, Denmark 16016900Microphone, EM-6717, Portless 15198100Receiver, BK1610 15197800Push Button Tube sleeve 26100668388Sleeve, Wire 11834-001Wire, ESW, Blue, 7x50µ 14 mm. 15130314Wire, ESW, Blue, 7x50µ 16 mm. 15130316Wire, ESW, Blue, 7x50µ 22 mm. 15130322Wire, ESW, Green, 7x50µ 8 mm. 15130208Wire, ESW, Green, 7x50µ 13 mm. 15130213Wire, ESW, Green, 7x50µ 16 mm. 15130216Wire, ESW, Green, 7x50µ 22 mm. 15130222Wire, ESW, Green, 7x50µ 24 mm. 15130224Wire, ESW, Green, 7x50µ 28 mm. 15130228Wire, ESW, Green, 7x50µ 32 mm. 15130032Wire, ESW, Red, 7x50µ 14 mm. 15130014Wire, ESW, Red, 7x50µ 16 mm. 15130016Wire, ESW, Red, 7x50µ 22 mm. 15130022Wire, ESW, Red, 7x50µ 28 mm. 15130028Wire, ESW, Red, 7x50µ 32 mm. 15130032Wire, ESW, Amber, 7x50µ 10 mm. 15130110Wire, ESW, Amber, 7x50µ 22 mm. 15130122Wire, ESW, Amber, 7x50µ 28 mm. 15130128
Option Part No.Trimmer,L,150K,PJ63,Green 16667500Trimmer,H,150k,PJ63,Yellow 16667600Trimmer,P,150K,PJ63,Black 16667700Push Button 10000601Telecoil 2238-429
Analog VC Complete Part No.VC, ASM, L 16857100VC, ASM, R 16857000
Note: For conformal coating EGC-17000, check the vendor website: www.3M.com to purchase locally. For conformal coating SL1367 peters coat, check the vendor website: www.peters.de to purchase locally.
Doc. No. 0175860 rev. F
Page 5 of 17
Faceplate Assemblies
VC, 3 Trimmer - Left, HP
VC, 3 Trimmer, Telecoil - Left, HP
VC, No Trimmer - Left, HP
VC, 2 Trimmer - Left, HP
Doc. No. 0175860 rev. F
Page 6 of 17
Blank faceplates
Blank FP Single mic. Part No.FP, 13, FLT VC, Light (L) 15185050FP, 13, FLT VC, Medium (L) 15185051FP, 13, FLT VC, Dark (L) 15185052FP, 13, FLT VC, Light (R) 15185060FP, 13, FLT VC, Medium (R) 15185061FP, 13, FLT VC, Dark (R) 15185062
Battery Door 13 Part No. Batt Door Left, Light 15185120 Batt Door Left, Medium 15185121 Batt Door Left, Dark 15185122 Batt Door Right, Light 15185110 Batt Door Right, Medium 15185111 Batt Door Right, Dark 15185112
13 FLT VC - Right13 FLT VC - Left
Doc. No. 0175860 rev. F
Page 7 of 17
Hybrid connections (C3.1 Flex)
H12
H11
H10
H13 H14
H17
H21 H22
H16 H15
H1
H2H3
H4
H5H6
H8
H7H9H20
H18 H19
H12
H11
H10
H13 H14
H17
H21 H22
H16 H15
H1
H2H3
H4
H5H6
H8
H7H9H20
H18 H19
MIC +
MIC -
MIC(0)
MODULEMODULE
BATT +
BATT -
REC -
REC +
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175860 rev. F
Page 8 of 17
Diagram - ITE Left
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175860 rev. F
Page 9 of 17
Diagram - ITE Right
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175860 rev. F
Page 10 of 17
Receiver assembly
BK1610 rec. wires are to be routed as shown.
BK1610 rec: Place foam-wrap p/n 15414300 as shown.
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175860 rev. F
Page 11 of 17
Prepare the faceplate - Trimmer Installation
Mark target hole. Drill target hole. Remove debris and insert trimmer,
Make trimmer flush even on the external side of faceplate.
Use Loctite 416 and glue around the trim-mer (internal side). Let it cure.
NOTE : Do the same process for additional trimmers. Let the glue cure first then operate the trimmer to ensure that it is not frozen.
Drill bit 0.076” or 1.93mm for the trimmer hole
Doc. No. 0175860 rev. F
Page 12 of 17
Prepare the faceplate - PB Installation
Insert PB on faceplate hole then-glue round the push-buttonusing Loctite 416 P/N 8066-599.
Let it air dry for 5 mins
Mark and drill a pilot hole using a smaller drill bit on a manual grinder.
Remove excess debris.
Use TC00298 drill bit and carefully drill onto the pilot hole. Drill all the way through.
Remove excess debris.
Doc. No. 0175860 rev. F
Page 13 of 17
Prepare the faceplate - VC Installation
Drill bit 0.159” or 4.038 mm for the Analog VC hole
Mark target hole. Drill target hole. Remove debris and insert Analog VC
Make sure that VC is not protruding too much above the highest point of the external side of faceplate.
Use Loctite 416 and glue around the VC (internal side). Let it cure.
NOTE : Let the glue cure first then operate the VC to ensure that it is not frozen.
Doc. No. 0175860 rev. F
Page 14 of 17
Options
Pad 10
TEL-Y10
TELECOIL ON MEMORY
Pad 11Pad 10Pad 10
TEL-Y10
TELECOIL ON MEMORY
Pad 11Pad 11
Telecoil
Push Button
Note: If a trimmer, PB and telecoil are opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the Turn Configuration Tool Software to reflect correct option added / removed. The Turn Configuration Software can be downloaded from the GTO website: http://gto.gnresound.com
P - TRIMMER L - TRIMMERH - TRIMMER
ES
AES
A ES
A
Doc. No. 0175860 rev. F
Page 15 of 17
Final Device
3 TRIMMER OPTION 2 TRIMMER OPTION
Doc. No. 0175860 rev. F
Page 16 of 17
Service Tool
When working on the assembled faceplate a heat sink (p/n 10158701) must always be used in order to prevent damages to the components.
The tool can be used on both sides. One side for size 13 and 312, the other side to be used for size 10
Size 13 and 312 Size 10
Doc. No. 0175860 rev. F
Page 17 of 17
Test Equipment
Both programming cable sets shown on this page can be used
Connect the flex to the programming cable by using the flex end marked with an arrow.• Programming cable CS63 p/n 50931702• Flex strip 10 pcs. p/n 50931703.
Programming cable CS44 :
P/n 9022 907 69029, Blue (L)P/n 9022 907 69019, Red (R)P/n 9022 907 69579, Flex adaptor CS44 (incl a flex strip)
The device is to be configured with either AUDIOMaster or TURN Configuration Software for trimmers, PB and tele-coil options. The Configuration Software can be downloaded from the GTO website http://gto.gnresound.com
When testing / programming a battery pill must be used: