TECHNICAL GUIDE - TKC · Vero handleless rail system Technical uide IMPORTANT PLEASE NOTE: The...
Transcript of TECHNICAL GUIDE - TKC · Vero handleless rail system Technical uide IMPORTANT PLEASE NOTE: The...
Date of print/release
December2017
TECHNICAL GUIDEVERO HANDLELESS RAIL SYSTEM
2 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
IMPORTANT PLEASE NOTE:The information contained in this literature is for illustrative purposes only to assist in choosing your desired kitchen. While we endeavour to keep the information up to date and correct we do not make any representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability and suitability of the doors and products that appear in this literature.
We aim to showcase as many different items as possible and therefore some products have been installed and photographed purely to show as many of our product features as possible and they should not be taken as an example of how they are intended to be installed in real kitchen installations.
It is therefore the responsibility of the installer to check the corresponding manufacturer’s installation information and the manufacturer’s technical information to ensure this is up to date and to ensure that the products can be fitted in a way they are displayed and the products are suitable for your requirements.
We specifically exclude any liability in this regard unless the products are fitted in accordance with the specifications we supply and the manufacturer’s installation recommendations are used in a way recommended by the manufacturer and in accordance with the manufacturer’s technical information provided.
The information shown in this literature is accurate as at the date of print/release shown on such information but it may be subject to changes after such date. Please therefore ensure that you are viewing the most current product information available and check with us if you have any doubt about the suitability of the product or accuracy of the information shown.
We are proud that all our products that we sell are covered by a statutory warranty but this does not stop all our products naturally ageing overtime. As a result of this natural ageing process we are therefore unable to provide an identical colour finish to the existing products you have purchased from us with any products that we supply you from the same product line. In such event our liability will be limited to the purchase price paid for the product you are seeking to replace.
Due to the limitations on photographic reproduction, colours may differ slightly from the actual products shown. Please note that board matches listed with the doors are a suggestion only and better board matches may be available on the market. It is up to the individual to decide on its suitability.
Please Note: The information shown in this literature is accurate as at the date of print/release shown on such information but it may be subject to changes after such date. Please therefore ensure that you are viewing the most current product available and check with us if you have any doubt about the suitability of the product or accuracy of the information shown.
3 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Description Handleless rail system
Finish / Material Aluminium
Lengths Top / Mid Profiles: 4100mm Vertical Profiles: 4200mm Wall Profile: 3900mm
Product Information
Vero Top Profile
VERO HANDLELESS RAIL SYSTEM
Vero handleless rail system with Vivo Matt doors in Anthracite
“We’re proud to introduce a true handleless system, offering the ultimate streamlined look for a minimalist designer kitchen.”
VERO MADE EASY Watch our videos: www.tkc.co.uk/vero-made-easy
1. VERO CABS 2. VERO RAILS 3. VERO DOORS
4 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
CODES & DESCRIPTIONS
TOP PROFILES - FOR BASE CABINETS
CODE DESCRIPTION
100TOP4100 Top profile for doors, 4100mm(L) x 56.5mm(H) x 27.2mm(D), aluminium
100TOPENDCAP End cap for top profile, aluminium - pair (1 LH, 1 RH)
100TOPINT90 Internal corner joint for top profile, 90 degrees, aluminium
100TOPEXT90 External corner joint for top profile, 90 degrees, aluminium
100TOPJOINT Joint section for top profile, aluminium
100QFIX Quick fix brackets for top and mid profiles, screw mounted - 1 pair (minimum order 25 pairs)
MID PROFILES - FOR DRAWERS
CODE DESCRIPTION
100MID4100 Mid profile for drawers, 4100mm(L) x 73mm(H) x 26mm(D), aluminium
100MIDENDCAP End cap for mid profile, aluminium - pair (1 LH, 1 RH)
100MIDINT90 Internal corner joint for mid profile, 90 degrees, aluminium
100MIDEXT90 External corner joint for mid profile, 90 degrees, aluminium
100QFIX Quick fix brackets for top and mid profiles, screw mounted - 1 pair (minimum order 25 pairs)
VERTICAL PROFILES - FOR TALL CABINETS
CODE DESCRIPTION
100VERTMID4200 Vertical profile intermediate, 4200mm(L) x 71.6(H) x 41mm(D), aluminium
100VERTEND4200 Vertical profile lateral, 4200mm(L) x 53.3mm(H) x 41mm(D), aluminium
100VERTSPACER Spacer for appliance, 580mm(L) x 19.6mm(H) x 20.8mm(D), aluminium
WALL CABINET PROFILES
CODE DESCRIPTION
100WALL3900 Wall cabinet profile, 3900mm(L) x 19.6mm(H) x 20mm(D), aluminium
10
3726
57.5
22.5
32
3
R 5
Ø 5
1
56.5
27.2
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU116DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU136DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
8006xxxL41 ML 4100 102,5 25 BOX146 4250x205x80 34,20 0,069
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8006TPxxx CF - 9 9 blister 0,56 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8006TPxxxC CF - 9 9 blister 0,40 -
PROFILI GOLA ORIZZONTALI - HORIZONTAL GOLA PROFILES
_Profilogolasottotop
_Gola profile
_
8006
Con le quote indicate si ottiene la sporgenza di 1 mm del Profilo Gola dal fianco. Se non si desidera avere la sporgenza, aumentare di 1 mm le quote indicate. ThequoteddimensionsconsidersthattheGolaProfilewillovercomethesideofthecabinetof1mm.IncasetheGolaProfilehastobeflushwiththecabinetsides,thenthequoteddimensionshastobeincreasedof1mm.
Scilm Catalogo 2015_pag interne_DEF.indd 118 13/04/15 15:46
Top ProfileExt. Corner Joint - Top
20
16
41
71.6
18
18.3
35
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
8019xxxL42 ML 4200 403,2 16 BOX147 4250x110x205 27,85 0,096
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
8020xxxL42 ML 4200 403,2 16 BOX147 4250x110x205 27,85 0,096
159
_Profilogolaverticaleintermedio
_Intermediate vertical gola profile
_
8019
QUOTA PRESA MANIGLIA 20 mm HANDLEGRIPDIMENSION20mm
PROF
ILI G
OLA
GOLA
PRO
FILE
Scilm Catalogo 2015_pag interne_DEF.indd 159 13/04/15 15:47
Vertical Profile - Intermediate
Spacer for Appliance
SG8007
27.5
AG8007
28.3
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AG8007-xxx NR - 18 18 blister 1,57 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SG8007-xxx NR - 18 18 blister 0,68 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
FGCSP0161-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AGP8007-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
TGCSP0160-xx CP - 100 100 BOX74 310x170x120 - 0,006
PROFILI GOLA ORIZZONTALI - HORIZONTAL GOLA PROFILES
_Angolo90°
_90° internal corner
_
AG8007
_Spigolo90°
_90° external corner
_
SG8007
Scilm Catalogo 2015_pag interne_DEF.indd 126 13/04/15 15:46
Ext. Corner Joint - Mid
8 20.8
MIN. 35
187.53
19.68
20.820.8
207
MIN. 35
20.8
6.5
3
8
16
7 20
17.6
20.8
20.8
MIN. 358
187.53
19.18
20.8
207
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
R1730xxxL39 ML 3900 117 30 BOX06 4040x80x205 33,35 0,066
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
R1717xxx07L39 ML 3900 97,5 25 BOX06 4040x80x205 38,51 0,066
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
R1725xxx07L39 ML 3900 1170 25 BOX06 4040x80x205 32,00 0,066
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L NR LXBXH KG M3
R1746xxxL39 ML 3900 117 30 BOX06 4040x80x205 33,35 0,066
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
R1719xxx07L39 ML 3900 1170 25 BOX06 4040x80x205 29,50 0,066
PROFILI GOLA PER PENSILI - GOLA PROFILES FOR WALL UNITS
_Profilogolaperpensile_Gola profile for hanging units_
R1730
_Profilogolaperpensile_Gola profile for hanging units_
R1746
_Profilogolaperpensileconguarnizione_Gola profile for hanging units with gasket_
R1717
Scilm Catalogo 2015_pag interne_DEF.indd 166 13/04/15 15:47
Wall Profile
10
Ø 5
R 5
R 5
26
37
32
20.5
20.5
73
1
73
26
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
8007xxxL41 ML 4100 41 10 BOX146 4250x205x80 16,50 0,069
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU116DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU136DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8007TPIxxxC CF - 9 9 blister 0,40 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8007TPxxx CF - 9 9 blister 0,25 -
PROFILI GOLA ORIZZONTALI - HORIZONTAL GOLA PROFILES
_Profilogolacassettiera/cestoni
_Gola profile for drawers
_
8007
Con le quote indicate si ottiene la sporgenza di 1 mm del Profilo Gola dal fianco. Se non si desidera avere la sporgenza, aumentare di 1 mm le quote indicate. ThequoteddimensionsconsidersthattheGolaProfilewillovercomethesideofthecabinetof1mm.IncasetheGolaProfilehastobeflushwiththecabinetsides,thenthequoteddimensionshastobeincreasedof1mm.
Se il profilo è impiallacciato la fresata deve essere di 74 mm e le quote 20,5 passano a 21,0. Incaseprofilewillbe“veneered”,millingquotewillbeof74mmanddimension20,5willbecome21,0.
Scilm Catalogo 2015_pag interne_DEF.indd 124 13/04/15 15:46
Mid Profile
5 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
PRODUCT RANGE OVERVIEW
Quick Fix Brackets 100QFIX
Used to attach profile to cabinet(screw mounted)
SG8007
27.5
AG8007
28.3
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AG8007-xxx NR - 18 18 blister 1,57 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SG8007-xxx NR - 18 18 blister 0,68 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
FGCSP0161-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AGP8007-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
TGCSP0160-xx CP - 100 100 BOX74 310x170x120 - 0,006
PROFILI GOLA ORIZZONTALI - HORIZONTAL GOLA PROFILES
_Angolo90°
_90° internal corner
_
AG8007
_Spigolo90°
_90° external corner
_
SG8007
Scilm Catalogo 2015_pag interne_DEF.indd 126 13/04/15 15:46
SG8007
27.5
AG8007
28.3
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AG8007-xxx NR - 18 18 blister 1,57 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SG8007-xxx NR - 18 18 blister 0,68 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
FGCSP0161-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
AGP8007-xx CP - 100 100 BOX74 310x170x120 - 0,006
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
TGCSP0160-xx CP - 100 100 BOX74 310x170x120 - 0,006
PROFILI GOLA ORIZZONTALI - HORIZONTAL GOLA PROFILES
_Angolo90°
_90° internal corner
_
AG8007
_Spigolo90°
_90° external corner
_
SG8007
Scilm Catalogo 2015_pag interne_DEF.indd 126 13/04/15 15:46
Used for base units (4100mm length)
Used for drawers(4100mm length)
Used between two larder units
(4200mm length)
Used to finish off top profiles
Used to finish off mid profiles
Used with one larder unit
(4200mm length)
Connects top profiles at internal
corners
Connects mid profiles at internal
corners
Connects top profiles at
external corners
Connects mid profiles at
external corners
Connects lengths of top
profiles
Top Profile & Accessories:
Mid Profile & Accessories:
Vertical Profiles & Accessories: Wall Profile:
Top Profile100TOP4100
Mid Profile100MID4100
Vertical Profile - Intermediate
100VERTMID4200
End Caps - Top100TOPENDCAP
End Caps - Mid100MIDENDCAP
Vertical Profile - Lateral
100VERTEND4200
Int. Corner Joint - Top
100TOPINT90
Int. Corner Joint - Mid 100MIDINT90
Ext. Corner Joint - Top
100TOPEXT90
Ext. Corner Joint - Mid
100MIDEXT90
Joint Section 100TOPJOINT
Quick Fix Brackets 100QFIX
Used to attach profile to cabinet(screw mounted)
Conceals gap behind appliances
(580mm length)
Spacer for Appliance
100VERTSPACER
Used for wall units(3900mm length)
Wall Cabinet Profile
100WALL3900
6 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
DOOR RANGES
The Vero handleless rail system is available with the following 5 door ranges:
Vivo+ Matt x 5 matt colours
Description Slab door
Finish Matt
Base Material 18mm MF MDF
Covering Material Painted
Anthracite Cashmere Ivory Light Grey White
Vivo+ Gloss x 7 high gloss colours
Description Slab door
Finish High gloss
Base Material 18mm MF MDF
Covering Material Painted
Anthracite Cashmere Ivory Light Grey Porcelain Stone White
7 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Coniston ‘Premier’ (made to measure) x 30 coloured vinyls
Description Made to order slab door
Finish Various
Base Material 18mm MDF
Covering Material Vinyl wrapped
Beech
Light Grey Oak
Mussel Oak
Walnut
Pale Cream
White Ash
Graphite Oak
Matt Dakar Matt Dust Grey
Swiss Pear
Dakar Oak Dust Grey Oak
Maple Matt Cashmere
Lyon
Rift Oak
Grey Bardolino
Matt Mussel
Vanilla Text White Text
ChestnutCashmere Oak
Lissa Oak
Portofino Cherry
White Avola
Grey Avola
Matt Light Grey
Tobacco
White Oak
Ivory Oak
Glacier (made to measure) x 12 high gloss colours
Description Made to order slab door
Finish High gloss
Base Material 20mm MDF
Covering Material Acrylic on all door colours (except Noce which is vinyl)
Metallic Blue Metallic Champagne
Cashmere Dust Grey GraphiteBlack Jasmine Light Grey
Sand Beige VanillaTruffle White
Description Made to order slab door
Finish Super matt
Base Material 18mm MDF
Covering Material Super matt vinyl, polypropylene edged
Lastra (made to measure) x 8 super matt colours
GraphiteCashmere
Light Grey Stone Grey
Fjord
Mussel White
Dust Grey
8 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Top Profile
Code 100TOP4100
Finish / Material Aluminium
Dimensions 4100 x 56.5 x 27.2mm
Accessories available Quick Fix Brackets (100QFIX) End Cap - Top (100TOPENDCAP) Internal Corner Joint - Top (100TOPINT90) External Corner Joint - Top (100TOPEXT90) Joint Section (100TOPJOINT)
• Used for base unit doors and top drawers.
• Can be cut to size using a circular chop saw.
• Secured to cabinets with Quick Fix Brackets.
• Profiles can be finished off with End Caps before fitting.
• Top profiles can be linked at internal and external corners using Corner Joints.
• Straight lengths of top profiles can be linked together using the Joint Section.
• Base cabinets need to be routered, unless using TKC’s pre-routered Vero Quickcab.
* nb. If installing integrated under counter appliances please increase leg height to allow for easy installation of appliance. See p. 10 for more information.
720
150*
870*
685
27
3457.5
Worktop
Doo
r / D
raw
er F
ront
Cabinet top rail Top Profile
100TOP4100
Quick Fix Bracket 100QFIX
56.5
27.2
DIMENSIONS
BASE CABINET DIMENSIONS
FITTED DETAIL BASE CABINET ROUTING
38
27
22.5
323
R5
57.5
Base cabinet
Cabinet top rail
1. Top Profile (100TOP4100)2. Internal Corner Joint - Top (100TOPINT90)3. External Corner Joint - Top (100TOPEXT90)4. Quick Fix Bracket (100QFIX)5. End Cap - Top (100TOPENDCAP)
Base cabinet
BASE UNIT COMPONENTS
9 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Mid Profile
* nb. If installing integrated under counter appliances please increase leg height to allow for easy installation of appliance. See p. 10 for more information.
Dra
wer
Fro
nt
Dra
wer
Fro
nt
Quick Fix Bracket 100QFIX
73
26
DIMENSIONS
BASE CABINET DIMENSIONS
FITTED DETAIL BASE CABINET ROUTING
Code 100MID4100
Finish / Material Aluminium
Dimensions 4100 x 73 x 26mm
Accessories available Quick Fix Brackets (100QFIX) End Cap - Mid (100MIDENDCAP) Internal Corner Joint - Mid (100MIDINT90) External Corner Joint - Mid (100MIDEXT90)
• Used for mid and bottom drawers.
• Can be cut to size using a circular chop saw.
• Secured to cabinets with Quick Fix Brackets.
• Profiles can be finished off with End Caps before fitting.
• Mid profiles can be linked at internal and external corners using Corner Joints.
• Base cabinets need to be routered, unless using TKC’s pre-routered Vero Quickcab.
Cabinet
Mid Profile 100MID4100
Cabinet
R5
R5
38
27
32 73
20.5
20.5
720
150*
870*
27
3434
325
160
160
280
309.
557
.573
2734
3449
016
0
120
470
57.5
73
27
3434
325
325
280
309.
557
.573
2 x
325m
m D
raw
ers
2 x
160m
m D
raw
ers
& 1
x 3
25m
m D
raw
er
1 x
160m
m D
raw
er &
1 x
490
mm
Doo
r(P
leas
e no
te, w
e do
not
sup
ply
a pr
e-ro
uter
ed c
arca
se fo
r thi
s co
mbi
natio
n.)
2 DRAWERS 3 DRAWERS DRAWERLINE
10 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Installing under counter appliances
Integrated dishwasher
Under mounted oven
• The Top Profile (100TOP4100) can be used to run above an integrated appliance.
• It is recommended to set integrated dishwasher height at 815mm and adjust carcase legs to a min. height of 155mm. Please note, these dimensions are based on standard height dishwasher. Cabinet legs may need to raised further if appliance height is different.
• Metal brackets (supplied with dishwasher) should be fixed to the outer face of adjacent cabinets. Please note, an additional bracing baton may be required to the rear of the machine to help reduce movement.
• If drawers are situated next to an integrated appliance, we recommend using end caps to cover any gaps.
• The Top Profile (100TOP4100) can’t be used in conjunction with an under mounted oven. Profiles must stop on each side of the appliance and can be finished with End Caps.
• If using a freestanding cooker, end panels will need to be fitted on either side of the appliance and the profile needs to be finished against the panel.
Quick Fix Bracket 100QFIX
Top Profile 100TOP4100
Worktop
Doo
r
Dis
hwas
her D
oor
Cabinet top rail
Integrated Dishwasher
IMPORTANT INFORMATIONWe recommend extending the
cabinet legs to a minimum height of 155mm to ensure the integrated dishwasher will fit easily.
Always check the minimum height of your under counter appliances before
installing your Vero kitchen to ensure there is enough clearance under the top rail.
Top Profile 100TOP4100
Mid Profile 100MID4100
End Cap - Mid 100MIDENDCAP
Under mounted
oven
End Cap - Top 100TOPENDCAP
Integrated dishwasher with Vero handleless rail system
Min
. 15
5mm
Carcase
Carcaselegs
11 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Vertical Profile - Intermediate
Code 100VERTMID4200
Finish / Material Aluminium
Dimensions 4200 x 71.6 x 41mm
Accessories available 100VERTSPACER
• Used on tall units when two opening doors meet.
• Secured to cabinet gables with 25mm cabinet screws.
• Can be cut to size using a circular chop saw.
• A 35mm spacer (not supplied) is required at the back between the two cabinets to maintain the void created by the profile trim.
• The front of the cabinet gables need to be set back by 20mm for the trim to overlap behind the doors (unless using TKC’s Vero Quickcab).
2016
41
71.6
35
DIMENSIONS
FITTED DETAIL APPLICATION BETWEEN TWO DOORS
2016
4136
71.6
35
35
35
Optional Spacer (not supplied)
25mm screws
Larder Door
Cabinet Back
Cabi
net G
able
Cabi
net G
able
Larder Door
Cabinet Back
1818
Don’t forget to add 35mm spacing in
between larder units.
12 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Vertical Profile - Lateral
Code 100VERTEND4200
Finish / Material Aluminium
Dimensions 4200 x 53.3 x 41mm
Accessories available 100VERTSPACER
• Used on tall units when you have an opening door on one side only, can also be used to end a run where an end post or end panel is fitted.
• Secured to cabinet gable with 25mm cabinet screws.
• Can be cut to size using a circular chop saw.
• A 35mm spacer (not supplied) is required at the back between two cabinets, or between a cabinet and end panel.
• The front of the cabinet gable needs to be set back by 20mm for the trim to overlap behind the door (unless using TKC’s Vero Quickcab).
• To fix an end post or end panel to the profile you need to drill through the screw support channel and attach the end post from the inside of the cabinet with a 60mm screw.
2016
41
53.3
35
DIMENSIONS
FITTED DETAIL APPLICATION BETWEEN TWO DOORS
2016
41 36
53.3
35
35
Optional Spacer (not supplied)
25mm screws (A 60mm screw applied from the inside of the
cabinet is recommended if fitting against an end
post / end panel)
Larder Door
Cabinet Back
Cabi
net G
able
Cabi
net G
able
Larder Door
Cabinet Back
35
Don’t forget to add 35mm spacing in
between larder units.
13 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Spacer for Appliance
Code 100VERTSPACER
Finish / Material Aluminium
Dimensions 580 x 19.6 x 20.8mm
• Used to conceal the space behind the front of an appliance when used in an appliance housing unit combined with vertical Vero profiles.
• Fixed into the cabinet gable with 3 screws (4 x 16mm).
• Works with both intermediate and lateral vertical profiles.
• The trim can be cut down to suit different sized appliances. If doing so, we recommend that a metal file is used to remove any sharp edges on the cut edge and that it is positioned out of sight.
• If the appliance requires a screw fixing into the cabinet, the spacer can be drilled into to accomodate the screws.
• Nb. When stacking appliances, we recommend leaving a 10mm gap to the top and bottom of both appliances.
8.2
43
11.3
16R 1.5
1
R 5
580
DIMENSIONS FITTED DETAIL
APPLIANCE INSTALLATION
16
35 43
Larder Door Appliance
Spacer for Appliance 100VERTSPACER
Vertical Profile - Intermediate
100VERTMID4200
Cabi
net G
able
Cabi
net G
able
4 x 16mm screws
14 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Wall Cabinet Profile
Code 100WALL3900
Finish / Material Aluminium
Dimensions 3900 x 19.6 x 20mm
Accessories available N/A
• Concealed rail used on wall units.
• Can be cut to size using a circular chop saw.
• The base panel on the wall cabinet must be set back with 20mm to accommodate the rail profile within the cabinet (unless using TKC’s Vero Quickcab).
• The base panel must also have a 8mm deep, 3mm high routered groove for the profile to slot into (pre-routered on TKC’s Vero Quickcab).
• Clear silicone adhesive should be used to bind the rail with the panel.
DIMENSIONS FITTED DETAIL CABINET ROUTING
19.6
88
20
20.8
7
18
8
7.5
7.5
3
20Wall cabinet base panel
Doo
r
20
Vero handleless rail system with Vivo Gloss doors in Stone
15 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
12
3
12
3
SU136 ASS gola a L
SU116 ASS gola a L
56.5
27.52
58
293
_Terminaledx+sx_End cap Rh + Lh_
CF8006TP
_Terminaledx+sx
_End cap Rh + Lh
_
CF8006TPXXXC
17
40
16.5 9.53
16.53
17
40
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU116DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
SU136DS590000 CP - 300 300 BOX01PB 400x300x200 3,30 0,024
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
L ML NR LXBXH KG M3
8006xxxL41 ML 4100 102,5 25 BOX146 4250x205x80 34,20 0,069
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8006TPxxx CF - 9 9 blister 0,56 -
CODE UNIT DIMENSION MINORDERQTY PCS/BOX BOXSIZES WEIGHT VOLUME
NR NR LXBXH KG M3
CF8006TPxxxC CF - 9 9 blister 0,40 -
119
_Supportorapidoattaccoavite
_Screw fixing quick support
_
SU116
_Supportorapidoconpioli
_Pins fixing quick support _
SU136
PROF
ILI G
OLA
GOLA
PRO
FILE
Scilm Catalogo 2015_pag interne_DEF.indd 119 13/04/15 15:46
Quick Fix Brackets
Code 100QFIX
Finish / Material Plastic
Dimensions N/A
Accessories available N/A
• Screw mounted brackets for top and mid profiles.
• Comes in pairs (min. order 25 pairs).
Step 1. Attach quick fix brackets (100QFIX) to routered cabinet gables using screws.
Step 2. Slide the connectors into the back of the profile and turn 90 degrees.
Step 3. Apply profile to routered cabinet and push connectors into brackets to secure the profile to the cabinet.
FITTING TOP AND MID PROFILES
See video of how to attach the rails here: www.tkc.co.uk/vero-made-easy
16 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
External Corner Joint - Top
Code 100TOPEXT90
Finish / Material Aluminium
• Used to connect two top profiles running around an external corner or an island unit, to be used together with an external corner post.
• Secured to the top profile using two screws (supplied). • Nb. A cut out needs to made on the routered gable end to accommodate the screw
heads behind the external corner joint (see Diagram 1 below).
27.5
27.5
External Corner Joint - Mid
DIAGRAM 1
Code 100MIDEXT90
Finish / Material Aluminium
• Used to connect two mid profiles running around an external corner or an island unit, to be used together with external corner posts.
• Secured to the mid profile using two screws (supplied). • Nb. A cut out needs to made on the routered gable end to accommodate the screw
heads behind the external corner joint (see Diagram 1 below).
Before applying the corner joints to the cabinets, a hole needs to be notched out of the routered gable end to accommodate the two screw heads at the back of the corner joints.
27.5
27.5
Cabinet
Routered section
cut out for screw heads
17 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Internal Corner Joint - Mid
Code 100MIDINT90
Finish / Material Aluminium
• Used to connect two mid profiles at an internal corner, to be used together with internal corner posts.
• Secured to the mid profile using two screws (supplied).
28.3
28.3
Top Joint
Code 100TOPJOINT
Finish / Material Aluminium
• Used to join together lengths of top profiles.
• Held in place with 4 grub screws (supplied). Grub screw secured with Allen key.
• When using top joints an 8mm spacing must be taken into account when cutting down the profiles that are being joined together.
28.5
89
6.3
56.5
Internal Corner Joint - Top
Code 100TOPINT90
Finish / Material Aluminium
• Used to connect two top profiles at an internal corner, to be used together with an internal corner post.
• Secured to the top profile using two screws (supplied).
28.3
28.3
18 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
End Caps - Top
End Caps - Mid
Code 100TOPENDCAP
Finish / Material Aluminium
Code 100MIDENDCAP
Finish / Material Aluminium
• Used at the end of a top profile for example against a wall, end panel or next to appliances such as under mounted oven.
• Secured to the top profile using a grub screw (supplied). Grub screw secured with Allen key.
• When using end caps, a 2mm spacing must be taken into account when cutting down the trim.
• Used at the end of a mid profile for example against a wall, end panel or next to appliances such as an under mounted oven.
• Secured to the mid profile using a grub screw (supplied). Grub screw secured with Allen key.
• When using end caps, a 2mm spacing must be taken into account when cutting down the trim.
27.5 2
56.5
2
73
27.3
19 Tel 0161 336 3636Fax 0161 336 3638
Web www.tkc.co.ukEmail [email protected]
Vero handleless rail system - Technical Guide
Door CombinationsSuggested door & drawer combinations for the Vero handleless rail system
Nb: This page is to show door combinations and configurations only. Appliance heights will vary and may have an impact on oven filler / door sizes. Please check appliance heights and specifications before purchasing and installing any doors.
* Plinth height may vary. If integrated under counter appliances are installed, please raise cabinet legs to ensure appliance fits easily underneath the top rail. See p. 10 for more info.** TKC don’t supply Vero Quickcab carcases for this door combination.
Full length doors & appliancesStudio height installation (1250mm). Doors using vertical profiles are standard TKC door sizes. Doors using horizontal profiles are specifically designed to suit Vero.
1245
150mm* plinth
Full Length Doors
296396446496596
Double Oven
Single Oven
Single Oven
Single Oven
Microwave/ Coffee Maker
Microwave / Coffee Maker
Microwave / Coffee Maker
570 570325 325
685
325160715
175
filler
filler filler filler
Base & wall unit doors Medium height (1970mm) & tall height (2150mm) installation. Base unit door sizes are designed specifically to suit Vero profiles. All wall unit doors are standard TKC door sizes.
685
150mm* plinth
147296315346396
446496546596
296396446496596
496596796896996 596 596
496596796896996
227296346396
446496546596
496596796896996
496596796896996
596 596Built
Under Oven
490
160** 160
160
325 325
325
895715
355
355355490 450
110
Full length doors & appliancesMedium height installation (1970mm). All full length & appliance unit doors are standard TKC door sizes.
490
1965
150mm* plinth
Full Length Doors
296396496596
Fridge / Freezer
Fridge / Freezer
Microwave Oven / Coffee Maker
& Single Oven
Microwave Oven & Single Oven
Double Oven
Fridge / Freezer
Single Oven
1245
1245
715 715
645715980
980
450
450 570 490
490
Full length doors & appliancesTall height installation (2150mm). All full length & appliance unit doors are standard TKC door sizes.
490
570
150mm* plinth
Fridge / Freezer
Fridge / Freezer
Fridge / Freezer
Double Oven
SingleOven
1245
1245
895
895715
175
490
570450
980
980
570
filler
715
Microwave Oven / Coffee Maker
& Single Oven
Microwave Oven / Coffee Maker
& Single Oven
110
110175
1250
mm
2150
mm
2150
mm
1970
mm
1970
mm
150m
m*
150m
m*
150m
m*
150m
m*
150m
m*
460
460
460 460 460
600
600
600
600
600 600
600
600 600 600
filler filler filler
900
900
900
380
380
Contact usTelephone 0161 336 3636Fax 0161 336 3638Email [email protected] www.tkc.co.uk
Unit 3Cranberry DriveDentonManchesterM34 3UL
Area SalesScotland 07770 017422North East 07766 021114Yorkshire 07976 643485North West 07584 241838Merseyside & North Wales 07458119098East Midlands 07770 017440West Midlands 07899 948786South West & South Wales 07458 119099London & Home Counties (North) 07823 442668London & Home Counties (South) 07792 078830Northern Ireland 07391 40 5286
All goods are sold subject to our Terms and Conditions of Sale which are available upon request.
DATE OF PRINT/ RELEASE: December 2017 05VEROTECHBOOK