TBG Meeting NYC How to set up an N3 Network Step by Step_en.pdf · How to set up an N3 Network ......
-
Upload
hoangnguyet -
Category
Documents
-
view
213 -
download
1
Transcript of TBG Meeting NYC How to set up an N3 Network Step by Step_en.pdf · How to set up an N3 Network ......
Let’s start with…
What you need:
• PC or laptop with Internet connection
• SebaDataView (installed)
• Pipenet map with planned Logger and GSMBox positions
•
Please check that all devices have the up to date
firmware !!!
All devices have to be turned off at the beginning of an
installation !!!
2
positions
• Pen and paper to take notes
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY
Creating the N3 Network with the SebaDataView
• Open the SebaDataView Software
• Create a folder by clicking “New Folder”, or
do a right click on SebaData
• Enter the folder‘s name, then click “OK”
• Create a zone by clicking “New Zone”, or do a
right click on the folder that you have created
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 3
right click on the folder that you have created
• Enter the zone‘s name, then click “OK”
• Create a group by clicking “New Group”, or
do a right click on the zone you have created
(in versions after 3.0.6.6)
Adding the GSM-Box
• When using the new version (> 3.0.6.6) you must
also create a group. When not please
continue below.
• Click on the icon GSMBox3 (at the top of the
software), or do a right click on the zone you have
created to add the GSM Box
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 4
• Type in the ID (is on the GSM Box), then click “OK”
Programming the GSM Box
• Please keep in mind that the PC or Laptop
must have connection to the Internet!
• Go to the zone you have created
• Click on your GSMBox
• Click either on “Program” (at the top), or do a
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 5
• Click either on “Program” (at the top), or do a
right click on your Box and then click on
“Program”
• Insert necessary data in the blank
fields (Comment, Internet
Settings, FTP Settings,
Measurement settings, E-Mail-
Settings, E-Mail Destination, SMS
Destination, Ration Settings)
• Click “OK” to create a folder on
the FTP server
Programming the GSM Box
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 6
Add your loggers
Please keep in mind that the SebaLog RI must be
connected to the PC or laptop.
• Click at the top of the software “LogN3”, or do a
right click on your zone
• Turn the loggers right side up to turn them on
• Logger comment and ID will be automatically
inserted
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 7
inserted
Logger turned on Logger turned off after 3
minutes
Transferring the Data from SebaDataView to Commander 3
• Connect the Commander 3 to the PC or laptop with
the USB cable VK 77.
• On the Commander, press on the tool icon (bottom
right), then press “Connect to PC” and then again
“Connect”
• Please wait until the installation is finished!
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY8
• Click on the zone you want to export
• Click either “Export”, or do a right click on “Zone”
and then select “Export group”
• Select export to “Commander 3”
Transferring the Data from SebaDataView to Commander 3
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 9
• Select export to “Commander 3”
• Your zone will be shown in the Commander 3
under “Group management”
Setting up your Group in the Commander
• Click on the tool icon (bottom right)
• Go to “Group management”
• Select the group you have imported
• Press “ESC” (escape) on the Commander, or
click on the arrow at the bottom right
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 10
• The first time you program your N3
Network, you need to check your default
settings, so your loggers will measure the
way you want them to
• Click on the tool icon again (bottom right)
• Scroll down and select “Default logger settings”,
then click “OK”
• On the next screen, select “Network mode”
You only need to do this once!
• Select your settings, then click “Accept”
Setting up your Group in the Commander
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 11
• Select your settings, then click “Accept”
• It is recommended that you select the same radio
settings you made when programming the GSM
Box.
Setting up your group in the Commander/ Add or replace a logger
• Click on “Logger Management” to see the loggers
in the group you have selected
• Here, you can add or replace the loggers and also
change the comment
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 12
Programming the GSM Box
GSM programming and check should be done on site.
• Go to the main screen
• Press on the icon Antenna/Logger (bottom left)
• On the next screen, click “Install GSM-Box”
On the next screen, re-check your details by pressing
“Details” before programming the GSM-Box.
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 13
“Details” before programming the GSM-Box.
Programming the GSM Box
• Press “Prog. GSM-Box”
• On the new screen, you will see your comment
and the GSM Box ID
• Press “Program”
• Wait until all tests are done (color green)
• When everything is green, your GSM Box has
been successfully programmed
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 14
been successfully programmed
Do the GSM Test
• Scroll to “Check GSM” and press
• On the next screen, click “Send command”.
•
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 15
• On the next page, the Commander sends an order to
the GSM Box
• The GSM Box performs several tests to ensure
connection to the FTP server
• Tests are passed when they are marked green
Dual Tests
• Dual Tests are needed to verify the communication of devices with each other
• Install the device in the location where is needed
• Click “Dual test”
• On the next screen, insert the device ID by clicking on the tool icon
• On the next screen, press “Enter”
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 16
Dual Test
• Select a device (Attention! Please select the correct device!)
• In the example below, I have selected the GSM-Box and Logger
• In the example below, the Box ID is 412 and the Logger ID 2233
• Press “Start Dual test”
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 17
Dual Test
• After pressing “Start Dual test”, a screen will come up showing the test
• The bar should be always in the green area
• Let 15 to 20 packages pass through before pressing “Stop”
Please bear in mind that each device in a path has to communicate with its neighbors. To ensure a stable connection between them you need to check thiswith a dual test
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 18
with a dual test
• At this test we should receive almost any packet. A cause for lost packets could be:- A bad connect between dual test partners (Value is in the yellow area)- The position of the commander is unfavorable (Value is in the green area)- There is a radio interference (Value is in the green area)
• After pressing “Stop”, press “Yes” to save the connection
GPS Position
• On then the next screen, press “Store” to store the GPS positions
Please keep in mind that you need the GPS positions of each device that hasbeen installed!
• When you start the installation, you will need to get the GPS positions from the GSM Box and logger or repeater respectively
• Press „Finish“
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 19
• Have you at least missed one GPS position for the currently used dual test partners, there is a warning.
• If you do not have the possibility to record GPS positions, press „Yes“. To work with mapswon‘t be possible then!!!
IN THE CLOUD DATA CAN ONLY BE SHOWN FROMDEVICES WITH GPS POSITION !!!
With „No“ you can go back to the „Store GPS Position“ dialog.
Dual Test
Below, an example of how a Dual Test should look like and how to save the GPS positions.
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 20
Path Management
• Press the arrow until you see the screen “Path management”,
or go to the main screen and press the icon antenna/battery.
• On the next screen, select “Path Management”
• On the next screen, select the logger (by scrolling) that you
want to install. Attn! Each logger must be installed separately!
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 21
• Press “Install Path”
• Press “Continue”
Path Management
• The next screen shows you the connection between your
logger(bottom) and your GSM Box (top)
• Insert the repeaters by hand, or scroll over to “Map”
Using the map is much easier and faster!
• Press the check mark to create the path from the logger
through the repeaters to the GSM Box
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 22
through the repeaters to the GSM Box
• You can change the path direction by using the arrow button
next to the check mark. If you have chosen the wrong
direction you can undo the path with the “Clear” button
• The list of repeaters will show up on the right side
• Press “OK” to return to the initial screen, where you will see
the repeaters you have inserted
Path Management
• Press “Start Installation” to install the path
• If you see “Installation: OK”/ “Path test: OK”, your
installation has been successful. If not, please redo the
installation.
• Check your list to see if you have forgotten any loggers
• After installing all loggers, proceed with “Read device
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY 23
• After installing all loggers, proceed with “Read device
configuration” to read the configuration of the GSM-Box
• Press “Read GSM-Box config.”
• Read configuration
• Press the “Next” button until you come too the screen
on the right. Here will be a list of all the Loggers that
have been installed
• You are now officially finished
End of installation.
If you have followed these instructions exactly, you will
see your network the next day after the first upload to
the server.
Keep in mind that on the first day, you can work as
long as you like. The Radio on time will be activated by
the first upload to the server.
© 2012 SebaKMT – Measuring and locating techniques – MADE in GERMANY24