TB-FMCL-PH HWUserManual 02 01e - Fujitsu · Rev.0.01 2009.09.17 Preliminary Nagatani Rev.0.02...
Transcript of TB-FMCL-PH HWUserManual 02 01e - Fujitsu · Rev.0.01 2009.09.17 Preliminary Nagatani Rev.0.02...
TB-FMCL-PH Hardware User Manual
1 Rev.2.01
TB-FMCL-PH
Hardware User Manual
Rev.2.01
TB-FMCL-PH Hardware User Manual
2 Rev.2.01
Revision History
Version Date Description Publisher
Rev.0.01 2009.09.17 Preliminary Nagatani
Rev.0.02 2009.09.22 Changes to the Sht.7 FMC(LPC) drawing Nagatani
Rev.2.00 2010.03.29 Release version Yoshioka
Rev.2.01 2010.04.07 Replaced Table 1 Odajima
TB-FMCL-PH Hardware User Manual
3 Rev.2.01
Table of Contents
1. Related Documents and Board Accessories ............................................................................... 7
2. Overview ...................................................................................................................................... 7
3. Features....................................................................................................................................... 7
4. Block Diagram.............................................................................................................................. 8
5. External View of the Board .......................................................................................................... 9
6. Board Specification ....................................................................................................................10
7. Description of Each Component................................................................................................ 11
7.1. Signal connection between Pin Header and FMC connectors................................................. 11
7.2. External power supply and ground connections....................................................................... 12
7.3. FMC Connector Signal Processing .......................................................................................... 13
7.3.1. Power Supply .................................................................................................................... 13
7.3.2. Test Points (TPs)............................................................................................................... 13
7.3.3. Signal Ground ................................................................................................................... 13
List of Figures
Figure 3-1 FMC Connector Pin Layouts ............................................................................................. 7
Figure 4-1 Block Diagram................................................................................................................... 8
Figure 5-1 Component Side ............................................................................................................... 9
Figure 5-2 Solder Side........................................................................................................................ 9
Figure 6-1 Board Dimensions (inclusive of a wasteable portion) ..................................................... 10
Figure 7-1 Power Supply and Ground Through-Holes ..................................................................... 12
Figure 7-2 FMC Connector Signal Ground Structures ..................................................................... 13
List of Tables
Table 1 Pin Header(CN2) Layout 1................................................................................................... 11
Table 2 Pin Header(CN3) Layout 2 ................................................................................................ 11
Table 3 Pin Header(CN4) Layout 3 ................................................................................................ 12
Table 4 FMC Power Supply Pin Layouts .......................................................................................... 13
Table 5 FMC Connector Signal Test Pads........................................................................................ 13
Table 6 FMC Connector Signal Ground ........................................................................................... 13
TB-FMCL-PH Hardware User Manual
4 Rev.2.01
Introduction Thank you for purchasing the TB-FMCL-PH board.
Before using the product, be sure to carefully read this User Manual and fully understand how to
correctly use the product.
Read through this manual and always keep it handy.
Safety Precautions Be sure to observe these precautions
Observe the precautions listed below to prevent injuries to you or other personnel or damage to property.
• Before using the product, read these safety precautions carefully to assure correct use.
• These precautions contain serious safety instructions that must be observed.
• After reading through this manual, be sure to always keep it handy.
The following conventions are used to indicate and classify precautions in this manual. Failure to
observe precautions can result in injury to people or damage to property.
Indicates the high possibility of serious injury or death if the product is handled
incorrectly.
Indicates the possibility of serious injury or death if the product is handled
incorrectly.
Indicates the possibility of injury or physical damage in connection with houses or
household goods if the product is handled incorrectly.
The following graphical symbols are used to indicate and classify precautions in this manual.
(Examples)
Be sure to turn off the power switch
Do not disassemble the product.
Do not attempt this.
Danger
Warning
Caution
!
TB-FMCL-PH Hardware User Manual
5 Rev.2.01
In the event of a failure, disconnect the power supply.
If the product is used as is, a fire or electric shock may occur. Disconnect the power supply
immediately and contact our sales personnel for repair.
If an unpleasant smell or smoking occurs, disconnect the power supply.
If the product is used as is, a fire or electric shock may occur. Disconnect the power supply
immediately. After verifying that no smoking is observed, contact our sales personnel for
repair.
Do not disassemble, repair or modify the product.
Otherwise, a fire or electric shock may occur due to a short circuit or heat generation. For
inspection, modification or repair, contact our sales personnel.
Do not touch a cooling fan (when installing it).
As a cooling fan rotates in high speed, do not put your hand close to it. Otherwise, it may
cause injury to persons. Never touch a rotating cooling fan.
Do not place the product on unstable locations.
Otherwise, it may drop or fall, resulting in injury to persons or failure.
If the product is dropped or damaged, do not use it as is.
Otherwise, a fire or electric shock may occur.
Do not touch the product with a metallic object.
Otherwise, a fire or electric shock may occur.
Do not place the product in dusty or humid locations or where water may
splash.
Otherwise, a fire or electric shock may occur.
Do not get the product wet or touch it with a wet hand.
Otherwise, the product may break down or it may cause a fire, smoking or electric shock
Do not touch a connector (gold-plated portion) on the product.
Otherwise, the surface of a connector may be contaminated with sweat or skin oil, resulting
in contact failure of a connector or it may cause a malfunction, fire or electric shock due to
static electricity.
Warning
!
!
!
!
!
!
!
TB-FMCL-PH Hardware User Manual
6 Rev.2.01
Do not use or place the product in the following locations.
• Humid and dusty locations
• Airless locations such as closet or bookshelf
• Locations which receive oily smoke or steam
• Locations exposed to direct sunlight
• Locations close to heating equipment
• Closed inside of a car where the temperature becomes high
• Staticky locations
• Locations close to water or chemicals
Otherwise, a fire, electric shock, accident or deformation may occur due to a short circuit or heat
generation.
Do not place heavy things on the product.
Otherwise, the product may be damaged.
■ Disclaimer This product is a board intended for conversion between the Samtec FMC connector and the 2.54mm
pitch pin header connector. Tokyo Electron Device Limited assumes no responsibility for any damages
resulting from the use of this product for purposes other than those stated.
Even if the product is used properly, Tokyo Electron Device Limited assumes no responsibility for any
damages caused by:
- Earthquake, thunder, natural disaster or fire resulting from the use beyond our responsibility, acts by a
third party or other accidents, the customer’s willful or accidental misuse or use under other abnormal
conditions,
- Secondary impact arising from use of this product or its unusable state (business interruption or
others),
- Use of this product against the instructions given in this manual or
- Malfunctions due to connection to other devices.
Tokyo Electron Device Limited assumes no responsibility or liability for:
- Erasure or corruption of data arising from use of this product
- Any consequences or other abnormalities arising from use of this product, or
- Damage of this product not due to our responsibility or failure due to modification
This product has been developed by assuming its use for research, testing or evaluation. It is not
authorized for use in any system or application that requires high reliability.
Repair of this product is carried out by replacing it on a chargeable basis, not repairing the faulty devices.
However, non-chargeable replacement is offered for initial failure if such notification is received within
two weeks after delivery of the product.
The specification of this product is subject to change without prior notice.
The product is subject to discontinuation without prior notice.
Caution
!
!
TB-FMCL-PH Hardware User Manual
7 Rev.2.01
1. Related Documents and Board Accessories
Related documents:
All documents relating to this board can be downloaded from our website. Please see attached paper on
the products.
Board accessories:
- FMC spacer set
M2.6 X 10 spacer (Duracon): 2
Screws with Duracon washer: 4
2. Overview
This board is intended to be used for conversion between Samtec FMC connector (Low-Pin Count)
and 2.54mm pitch pin header. The board has been designed for connection with low-pin-count
platform boards.
The board can support a high speed differential signal interface through the use of differential wire.
3. Features
FMC Connector: Samtec FMC (Low-Pin Count) connector
Pin Header: General-purpose 2.54mm pitch pin header
Figure 3-1 FMC Connector Pin Layouts
TB-FMCL-PH Hardware User Manual
8 Rev.2.01
4. Block Diagram
Figure 4-1 shows a block diagram of the TB-FMCL-PH board.
The FMC connector is mounted on the solder side of the board.
Figure 4-1 Block Diagram
Main Functions:
1. The connection between the FMC connector and the pin header
2. The external power supply and ground connections
TB-FMCL-PH Hardware User Manual
9 Rev.2.01
5. External View of the Board
Figures 5-1 and 5-2 show external views of the board.
Figure 5-1 Component Side
Figure 5-2 Solder Side
TB-FMCL-PH Hardware User Manual
10 Rev.2.01
6. Board Specification
External Dimensions: 78.8 mm (W) x 69 mm (H)
Layer Structure: 8-Layer
Board Thickness: 1.6 mm
Material: FR-4
FMC Connector: Samtec ASP-134604-01
General-Purpose Connector: Omron XG8W-3031
Figure 6-1 Board Dimensions (inclusive of a wasteable portion)
TB-FMCL-PH Hardware User Manual
11 Rev.2.01
7. Description of Each Component
7.1. Signal connection between Pin Header and FMC connectors
Table 1 shows signal connections between the Pin Header and the FMC connector.
Three Pin Header connectors are used and each connector is connected via a 12-pair (24-pin)
differential wire.
Table 1 Pin Header(CN2) Layout 1
FMC
Pin Signal Name PinHeader(CN2) Signal Name
FMC
Pin
- GND 1 2 GND -
H5 CLK0_M2C_N 3 4 CLK0_M2C_P H4
H8 LA02_N 5 6 LA02_P H7
H11 LA04_N 7 8 LA04_P H10
H14 LA07_N 9 10 LA07_P H13
H17 LA11_N 11 12 LA11_P H16
H20 LA15_N 13 14 LA15_P H19
H23 LA19_N 15 16 LA19_P H22
H26 LA21_N 17 18 LA21_P H25
H29 LA24_N 19 20 LA24_P H28
H32 LA28_N 21 22 LA28_P H31
H35 LA30_N 23 24 LA30_P H34
H38 LA32_N 25 26 LA32_P H37
- GND 27 28 GND -
- NC 29 30 NC -
Table 2 Pin Header(CN3) Layout 2
FMC
Pin Signal Name PinHeader(CN3) Signal Name
FMC
Pin
- GND 1 2 GND -
G3 CLK1_M2C_N 3 4 CLK1_M2C_P G2
G7 LA00_N_CC 5 6 LA00_P_CC G6
G10 LA03_N 7 8 LA03_P G9
G13 LA08_N 9 10 LA08_P G12
G16 LA12_N 11 12 LA12_P G15
G19 LA16_N 13 14 LA16_P G18
G22 LA20_N 15 16 LA20_P G21
G25 LA22_N 17 18 LA22_P G24
G28 LA25_N 19 20 LA25_P G27
G31 LA29_N 21 22 LA29_P G30
G34 LA31_N 23 24 LA31_P G33
G37 LA33_N 25 26 LA33_P G36
- GND 27 28 GND -
- NC 29 30 NC -
TB-FMCL-PH Hardware User Manual
12 Rev.2.01
Table 3 Pin Header(CN4) Layout 3
FMC
Pin Signal Name PinHeader(CN4) Signal Name
FMC
Pin
- GND 1 2 GND -
D9 LA01_N_CC 3 4 LA01_P_CC D8
D12 LA05_N 5 6 LA05_P D11
C11 LA06_N 7 8 LA06_P C10
D15 LA09_N 9 10 LA09_P D14
C15 LA10_N 11 12 LA10_P C14
D18 LA13_N 13 14 LA13_P D17
C19 LA14_N 15 16 LA14_P C18
D21 LA17_N_CC 17 18 LA17_P_CC D20
C23 LA18_N_CC 19 20 LA18_P_CC C22
D24 LA23_N 21 22 LA23_P D23
D27 LA26_N 23 24 LA26_P D26
C27 LA27_N 25 26 LA27_P C26
- GND 27 28 GND -
- NC 29 30 NC -
7.2. External power supply and ground connections
Power and ground provided from the FMC connector can be externally connected via the through- holes
(CN5-8) shown in Figure 7-1.
Figure 7-1 Power Supply and Ground Through-Holes
TB-FMCL-PH Hardware User Manual
13 Rev.2.01
7.3. FMC Connector Signal Processing
The following signal processing is performed for the FMC connector pins.
7.3.1. Power Supply
Three power lines are provided from the FMC connector. They can be monitored via the test points
(THs) shown in Table 4.
Table 4 FMC Power Supply Pin Layouts
FMC Pin No. Power Test Point
C35,C37 12V TH1
C39,D32,D36,D38,D40 3.3V TH2
G39,H40 V ADJ TH3
7.3.2. Test Points (TPs)
The board provides on-board test pads (TPs) to monitor the FMC connector pin signals.
Table 5 FMC Connector Signal Test Pads
FMC Pin No.
Pin No. Pin Name Test PAD
C34 GA0 TP1
D35 GA1 TP2
H1 VREF_A_M2C TP3
7.3.3. Signal Ground
The following signal ground structures can be implemented for the FMC connector pins. The resistors
are not mounted at shipment.
Figure 7-2 FMC Connector Signal Ground Structures
Table 6 FMC Connector Signal Ground
FMC Pin No.
Pin No. Pin Name Resistor
D1 PG_C2M R1
H2 PRSNT_M2C_L R2
TB-FMCL-PH Hardware User Manual
14 Rev.2.01
PLD Solution Division URL: http://www.inrevium.jp/eng/x-fpga-board/ E-mail: [email protected] HEAD Quarter : Yokohama East Square, 1-4 Kinko-cho, Kanagawa-ku, Yokohama City,
Kanagawa, Japan 221-0056 TEL:+81-45-443-4016 FAX:+81-45-443-4058