Tap Series FTP-1000,2000,4000 DATACOM FASTstart Guide ...DATACOM SYSTEMS INC Customer Service is...
2
Fiber taps allow you to make a copy of network traffic as it travels between two network devices. These highly reliable, non- powered devices are the perfect solution to collect and capture network traffic for application analysis. Tap Series FTP-1000,2000,4000 FASTstart Guide What is included? (1) Fiber tap w/ mounting bracket (for use with RMC-2 , RMC 12-2 or RMC-3, RMC 12-3) (1) Download Card/Faststart Guide (tells where to download more product information) For More information © 2015 Datacom Systems, Inc 541-0149-R DATACOM SYSTEMS INC Installation Follow the wiring diagrams shown below. Fiber taps are directional, and use specific inputs and outputs for TX and RX to work properly. Make sure to clean all connectors with compressed air and clean patch cable connectors prior to installation. Typical Insertion loss ratios*: •50/50 MM -4.2 dB •70/30 MM -3.0/-6.7 dB •50/50 SM -3.9 dB •70/30 SM -2.2/-6.3 dB (*approximate) Customer Service is available from our website: www.datacomsystems.com or by calling +1 315 463 9541 Find out more. Visit www.datacomsystems.com FTP-1000 Series Router Front View Analysis Tool Port 1 Port 2 MONITOR A B TX A TX B TX RX TX RX Link 1 TX NET 1A RX Link 1 TX RX NET 1B MON 1 Link 2 NET 2A TX A TX B NET 2B MON 2 TX A TX B TX RX TX RX TX NET 1A RX Link 1 TX RX TX A TX B NET 1B MON 1 Link 3 Link 2 Link 4 TX NET 2A RX TX RX TX A TX B NET 2B MON 2 TX NET 3A RX TX RX TX A TX B NET 3B MON 3 TX NET 4A RX TX RX TX A TX B NET 4B MON 4 Front View Firewall A Router A Firewall B Router B Router B Router A Firewall A Firewall B Router Firewall FTP-2000 Series FTP-4000 Series Front View Page 1
Transcript of Tap Series FTP-1000,2000,4000 DATACOM FASTstart Guide ...DATACOM SYSTEMS INC Customer Service is...
Fiber taps allow you to make a copy of network traffic as it travels between two network devices. These highly reliable, non-powered devices are the perfect solution to collect and capture network traffic for application analysis.
Tap Series FTP-1000,2000,4000 FASTstart GuideWhat is included? (1) Fiber tap w/ mounting bracket (for use with RMC-2 , RMC 12-2 or RMC-3, RMC 12-3)
(1) Download Card/Faststart Guide (tells where to download more product information)
For More information
© 2015 Datacom Systems, Inc 541-0149-R
DATACOMS Y S T E M S I N C
Installation Follow the wiring diagrams shown below. Fiber taps are directional, and use specific inputs and outputs for TX and RX to workproperly. Make sure to clean all connectors with compressed air and clean patch cable connectors prior to installation.
Typical Insertion loss ratios*: •50/50 MM -4.2 dB •70/30 MM -3.0/-6.7 dB •50/50 SM -3.9 dB •70/30 SM -2.2/-6.3 dB (*approximate)
Customer Service is available from our website: www.datacomsystems.com or by calling +1 315 463 9541
Find out more. Visit www.datacomsystems.com
FTP-1000 Series
Router
Front View
Firewall
Analysis Tool
Port1
Port2
MONITORA B
TXA
TXB
TX RX TX RX
Link 1
TX
NET1A
RX
Link 1
TX RX
NET1B
MON1
Link 2
NET2A
TXA
TXB
NET2B
MON2
TXA
TXB
TX RX TX RX
TX
NET1A
RX
Link 1
TX RX TXA
TXB
NET1B
MON1
Link 3Link 2 Link 4
TX
NET2A
RX TX RXTXA
TXB
NET2B
MON2
TX
NET3A
RX TX RX TXA
TXB
NET3B
MON3
TX
NET4A
RX TX RXTXA
TXB
NET4B
MON4
Front View
Firewall A
Router A
Firewall B
Router B
Router B
Router A
Firewall A
Firewall B
Router
Firewall
FTP-2000 Series
FTP-4000 Series
Front View
Page 1
Tap Series FTP-1000,2000,4000 FASTstart Guide
For More information
© 2015 Datacom Systems, Inc 541-0149-R
DATACOMS Y S T E M S I N C
Customer Service is available from our website: www.datacomsystems.com or by calling +1 315 463 9541
Page 2
Correct Wiring: When installing a Fiber Tap, it is important to make sure that the Tx and Rx fibers are connected to the respective ports on the Fiber Tap. When wired correctly, the traffic incoming on an Rx port will be split before being sent to two separate Tx ports (One copy to the other Network device, the other copy to Monitor).
Reverse Wiring: If the fibers are connected backwards, light will not be received on the monitoring port. This is because the internal coupler that splits the light is unidirectional.
To Avoid Reverse Wiring: Reverse wiring can be difficult to catch initially, since an incorrectly cabled Fiber Tap will still send light between the network ports and connectivity will be seen on both network endpoints. Be sure to check the for light on the monitor ports as well as the network ports when installing the Fiber Tap.
