Synthesis and Characterization of Permanent Magnetic Nanocomposites Kunpeng Su, Xuehong Cui, Zhongwu...
-
Upload
dominic-parker -
Category
Documents
-
view
213 -
download
1
Transcript of Synthesis and Characterization of Permanent Magnetic Nanocomposites Kunpeng Su, Xuehong Cui, Zhongwu...
Synthesis and Characterization of Permanent Magnetic NanocompositesKunpeng Su, XuehongKunpeng Su, Xuehong Cui, Zhongwu Liu, and Dechang ZengCui, Zhongwu Liu, and Dechang Zeng
IntroductionIntroduction
Suction cast magnetsSuction cast magnets
Melt-spun REFeB alloysMelt-spun REFeB alloys
The nanocomposite magnets were synthesized by The nanocomposite magnets were synthesized by various methods, as shown in Fig.1. various methods, as shown in Fig.1. The NdThe Nd22FeFe1414B/B/-Fe nanocomposite alloys ribbons were -Fe nanocomposite alloys ribbons were
prepared by argon arc melting and melt spinning.prepared by argon arc melting and melt spinning. The NdThe Nd22FeFe1414B/FeB/Fe33B nanocomposite bulk magnets were B nanocomposite bulk magnets were
produced by devitrifying the bulk metallic glasses (BMGs) produced by devitrifying the bulk metallic glasses (BMGs) with B-rich compositions of RE-Fe-Co-M-B. The BMG with B-rich compositions of RE-Fe-Co-M-B. The BMG precursors were prepared by suction casting.precursors were prepared by suction casting. Nd–Fe-B/nano-Fe Composite powders were synthesized Nd–Fe-B/nano-Fe Composite powders were synthesized by chemically depositing Fe nanoparticles on by chemically depositing Fe nanoparticles on 11.5Nd81Fe1.9Co5.6B hard magnetic powders with a 11.5Nd81Fe1.9Co5.6B hard magnetic powders with a average particle size of 100average particle size of 100 ~~ 200 µm. The Fe nanoparticle 200 µm. The Fe nanoparticle synthesis employed wet chemistry method according to the synthesis employed wet chemistry method according to the reaction: FeClreaction: FeCl22 + NaBH + NaBH44 +H +H22O→Fe(B) + NaCl + HO→Fe(B) + NaCl + H22 +H +H22O [1]. O [1].
The hard magnetic powders were immersed in the reaction The hard magnetic powders were immersed in the reaction solution and acted as a substrate onto which the Fe solution and acted as a substrate onto which the Fe nanoparticles formed and deposited.nanoparticles formed and deposited. XRD, SEM and VSM were used to characterize the microstructure and magnetic properties of experimental materials.
Since last decade, there has been great scientific interest in the preparation and processing of nanocomposite permanent magnets, due to the prediction of their high theoretical magnetic properties [1,2]. The basic principle in the nanocomposite magnet is to exchange couple a hard magnetic phase with high coercivity (jHC) and a soft magnetic phase with high magnetization (JS). The predicted value of the maximum energy product (BH)max in this composite system is about 120 MGOe, significantly higher than that obtained so far in the superior single-phase system NdFeB system, which is about 56 MGOe [3,4]. So the exchange couple behavior is particularly a useful way to develop superior permanent magnets. The most widely used materials today are NdFeB alloy, SmCo alloy , FePt alloy and hard ferrites in hard magnetic phase and Fe, Ni, Co, Fe(Co) in soft magnetic phase. So far, there are two routes to prepare such hard/soft nanocomposite magnets. Most of the efforts followed “top down” metallurgical routes, i.e., development of the nanostructure through rapid solidification or high-energy mechanical milling. The other route is “bottom up” approach which assembles composite material by attaching soft magnetic phase to hard magnetic phase [5]. We report here the recent work in SCUT China on the nanocomposite magnetic magnets by these two routes, including melt spinning, suction casting + annealing and chemical deposition.
ReferencesReferences[1] R. Skomski, J.M.D. Coey, Phys. Rev. B 48 (1993) 15812.[2] T. Schrefl, R. Fischer, J. Fidler, H. Kronmuller, J. Appl. Phys. 76 (1994) 7053.[3 T. Schrefl, J. Fidler, H. Kronmuller, Phys Rev B 49 (1994) 6100.[4] W. Rodewald, B. Wall, M. Katter, K. Uestuener, IEEE Trans. Magn. 38 (2002) 2955.[5] Girija S. Chaubey, Vikas Nandwana,et.al ,Chem. Mater. 2008, 20, 475–478
Bottom-up approachBottom-up approachExperimentalExperimental
0 500 1000 1500 200040
60
80
100
120
140
160
180
200
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
(BH
) max
, kJ/
m3
jH
C, kA/m
J r, T
Rapid quenched RE-FeCo-B-(M) alloys
Close symbols: Jr
Open symbols: (BH)max
8 10 12 14-0.02
-0.03
-0.04
-0.05
-0.06
-0.07
-0.30
-0.35
-0.40
-0.45
-0.50
, %
/K
Z (RE Content)
RE-RichSingle phase
Nanocomposite
, %
/K
(Nd0.25
Pr0.75
)Z(Fe
0.7Co
0.3)
94-zB
6
300~400K 300~473K 300~550K
Fig.2 Correlation between jHC, Jr and (BH)max for melt spun Nd-Fe-B based alloys with a wide range of compositions.
1. For melt spun REFeB alloys, upper limits of (BH)max (160-180 kJ/m3 or 19-21.5 MGOe) for are obtained at the coercivity range 400-800 kA/m (Fig.2).
2. Nanopcomposite alloys have better thermal stability than single phase and RE-rich phase alloys (Fig.3)3. Small additions have an important role in modifying the phase precipitation and the microstructure
(Fig.4).
Fig. 1 The Overview of Synthetic Routes
20 30 40 50 60 70 80
Theta(°
Inte
nsity
(Cou
nts)
#
##
*
***
* * * ** *
*
* * * * * * ** *
* Nd2Fe14B# Fe
(a) uncoated
(b) coated
(c) coated annealed
Fig.9 Morphology and XRD patterns for Nd–Fe-B/nano-FeNd–Fe-B/nano-Fe composite powders synthesized by chemical synthesizing Fe nanoparticles on Nd–Fe-B powdersNd–Fe-B powders
Fig.5 The photograph of as-cast rod of RE-Fe-Co-M-B BMG
Fig.6 XRD pattern of RE-Fe-Co-M-B as-cast rod, showing amorphous structure
←HCP
↖FCC
Fig.8 Morphology for FeCo magnetic nanoparticles deposited by chemical methods before (left) and after (right) heat treatment
Fig. 3 Temperature coefficiences of remanence () and coercivity () for NdPr-FeCo-B alloys
Fig.4 Top: DSC of RE-Fe-M-B Alloys with various Nb addition; bottom: XRD patterns for alloys without (a)
and with (b) Nb addition
30 40 50 60 70 80
Pr2Fe14B
Fe
Fe3BPr2Fe23B3
Inte
nsi
ty
2 (degree)
a
b
400 600 800
He
at F
low
624.9C
614.6C579.3C
627.4C
572.2C
577.9C
Temperature( C)
x=0
x=1
x=2
1. The soft magnetic Fe, Co and FeCo spherical nanoparticles with mean sizes of 20-50 nm were synthesized. Nanospheres chains and hcp-structured nanorods can be obtained by magnetic field assisted process and heat treatment, respectively.
2. The immersion of NdFeB micro-particles in the chemical solution of FeCl2+NaBH4 leads to the formation of NdFeB/nano-Fe composites, which provides a new approach to realize exchange coupling in hard/soft magnets.
Fig .7 The hysteresis loops of rapidly solidified RE-Fe-M-B saloys annealed at various temperatures
1. BMG rod with 2 mm in diameter was successfully prepared for 1. BMG rod with 2 mm in diameter was successfully prepared for RE-Fe-Co-M-B alloys, which can be devitrified to RE-Fe-Co-M-B alloys, which can be devitrified to NdNd22FeFe1414B/FeB/Fe33B nanocomposite magnet (Fig.5 and Fig.6).B nanocomposite magnet (Fig.5 and Fig.6).
2. High 2. High (BH)max (59.7 kJ/m3) can be achieved for these RE-Fe-Co-M-B alloys(Fig.7).
华南理工大学材料科学与工程学院磁性材料与功能薄膜学术团队
30 60 90
100
200
300
400
inte
nsity (co
un
ts)
2(degree)
Department of Metallic Materials Science and Engineering, School of Material Science and Engineering, South China University of Technology, Guangzhou, 610640, China
Research Group for Magnetic Materials and Functional Thin Films http://www.mmff-scut.com
melt spinning suction casting wet-chemical
P-1
P-1
P-5
Heat Treatment
P-7P-8
P-7
P-9
Construction analysis magnetic measurements
Analysis and discuss
High Performance Magnets
Process Optimization
P-12 P-13 P-14P-13
P-15 P-16
P-15
P-16
P-18
P-19
P-20
P-22
P-23
P-20
P-27
Composition design
Optimization