SYLLABUS OF ONE YEAR CONVENTIONAL COURSE

FOR THE TRADE OF

GENERAL ENGINEERING

BY

DIRECTORATE OF INDUSTRIES

ANDAMAN AND NICOBAR ADMINISTRATION

COURSE CONTENTS

Practical Competencies Theory

1st Month

Identification and use of tools and equipments like measuring tools, marking tools, cutting tools, holding tools and machineries (lathe machine, drilling machine, cutters, grinder machine etc.) and welding plants (Gas/Arc) etc.

Use of marking media, marking, filing centre punching, dot punching, cutting, drilling, tapping and making of fitting jobs etc.

Importance of safety and general precautions observed in the workshop/Institute and in the section

Importance of Science and Calculation to the trade skill and fundamental Arithmetical operations, Addition, Subtraction, Multiplication and Division.

2nd month

Practicing of different types of weld joints and different types of weld beads.

b) Preparation of job edges according to the job carrying load.

c) Practicing and making all different types of fabrication works.

Definition of speed, velocity, acceleration, mass, weight and difference between mass and weight.

Importance of Engineering, Drawing and its knowledge.

Use of Drawing Instruments.

Freehand sketching of straight lines, rectangles, circle, polygons etc.

Construct an orthographic projection from the given isometric view of shaped blocks in 3rd angle method.

3rd and 4th Month

Practicing of marking, punching, riveting and soldering etc.

Making of sheet metal joints, tray, mug, funnel, haven gunt, trunk box, door and windows etc.

Practicing and making all different types of fabrication works.

1. ENGINEERING METALS:-

Physical properties.

Mechanical properties. SHEET METAL WORK:-

a) Sheet metal hand tools. b) Sheet metal bench tools. c) Sheet metal machine tools. d) Sheet metal operations. e) Sheet metal joints. f) Soldering and brazing.

5th and 6th Month

Straight and wearing beads on MS

in Flat position.

Preparation of joints, edge

preparation.

Fillet Lap & T joints

Inside corner joint

Square butt joint

Single ‘V’ but joint

Identification of defects by Visual

inspection & correction of defects. Practicing and making all different

types of fabrication works.

WELDING (GAS AND ARC):-

Welding methods.

Gas and Arc welding tools and equipments.

Welding joints, bead and preparation of Edges.

Safety precautions for gas and arc welding.

7th and 8th month

Making and practicing of lathe cutting tools clearance angle (FCA, FSCA, BSCA, BCA) etc.

Practicing of Turning, facing and thread cutting (internal and external) etc.

Making Nut and bolt, pushes and round wheels etc.

Practicing and making all different

LATHE MACHINE:-

Types of lathe machines.

Accessories of lathe machines.

Lathe operations (outer operation and Inner operation)

Lathe cutting tools according to shape.

Lathe cutting tools according to work.

types of fabrication works.

9th and 10th Month

Dismantling and assembling

automobile engine, clutch, gear box,

rear axle etc.

Hot forging and cold forging in

Blacksmity

AUTOMOBILE MECHANISM:-

Engine operations.

Lubrication and cooling system of engine.

Suspension system.

Power transmission system of Automobile.

MECHANICAL POWER TRANSMISSION:-

Power transmission by year’s.

Types of Gear’s.

Power transmission by chain and sprocket.

Use of belts in power transmission.

Introduction to Blacksmithy

11th Month

Project Work : Individual

preparation of project work by

the trainees which will be

assessed for internal marks

Industrial visit

12th month

Exposure training in Fabrication units

with updated machines

As approved by:-

A&N Administration Port Blair

Issued by:-

Directorate of Industries A&N Administration Port Blair

General Information 1. Name of the trade :- General Engineering Trade (GET) 2. Duration of Training :- 01 Year

3. Entry Qualification :- Passed the 10th Class Examination Under 10+2 system of Education or its equivalent

4. Age Limit :- 18-35 years

01 WEEK:- Importance of safety and general precautions observed in the workshop/Institute and in the section.

01 WEEK:- Identification and use of tools and equipments like measuring tools, marking

tools, cutting tools, holding tools and machineries (lathe machine, drilling machine, cutters, grinder machine etc.) and welding plants (Gas/Arc) etc.

04 WEEKS FILING PRACTICE:- Use of marking media, marking, filing, centre punching, dot

punching, cutting, drilling, tapping and making of fitting jobs etc. 02 WEEKS WORKSHOP CALCULATION AND ENGINEERING DRAWING:-

a) Importance of Science and Calculation to the trade skill and fundamental Arithmetical operations, Addition, Subtraction, Multiplication and Division.

b) Definition of speed, velocity, acceleration, mass, weight and difference between mass and weight.

c) Importance of Engineering, Drawing and its knowledge. d) Use of Drawing Instruments. e) Freehand sketching of straight lines, rectangles, circle, polygons etc. f) Construct an orthographic projection from the given isometric view of shaped

blocks in 3rd angle method.

10 WEEKS :- THEORY 2. SHEET METAL WORK:-

g) Sheet metal hand tools. h) Sheet metal bench tools. i) Sheet metal machine tools. j) Sheet metal operations. k) Sheet metal joints. l) Soldering and brazing.

3. LATHE MACHINE:- a) Types of lathe machines. b) Accessories of lathe machines. c) Lathe operations (outer operation and Inner operation) d) Lathe cutting tools according to shape. e) Lathe cutting tools according to work.

4. WELDING (GAS AND ARC):-

a) Welding methods. b) Gas and Arc welding tools and equipments. c) Welding joints, bead and preparation of Edges. d) Safety precautions for gas and arc welding.

5. AUTOMOBILE MECHANISM:-

a) Engine operations. b) Lubrication and cooling system of engine. c) Syspension system. d) Power transmission system of Automobile.

6. MECHANICAL POWER TRANSMISSION:-

a) Power transmission by year’s. b) Types of Gear’s. c) Power transmission by chain and sprocket. d) Use of belts in power transmission.

7. ENGINEERING METALS:-

a) Physical properties. b) Mechanical properties.

PRACTICAL 30 WEEKS:- 1. a) Practicing of marking, punching, riveting and soldering etc. b) Making of sheet metal joints, tray, mug, funnel, haven gunt, trung box, door

and windows etc. 2. a) Making and practicing of lathe cutting tools clearance angle (FCA, FSCA,

BSCA, BCA) etc. b) Practicing of Turning, facing and thread cutting (internal and external) etc. c) Making Nut and bolt, pushes and round wheels etc. 3. a) Practicing of different types of weld joints and different types of weld

beads. b) Preparation of job edges according to the job carring loard. c) Practicing and making all different types of fabrication works.

4. a) Dismantling and assembling of automobile engine, clutch, gear box, rear axle etc.

x------- x-------x------x-------x-------x---------x--------x

SYLLABUS OF ONE YEAR CONVENTIONAL COURSE

FOR THE TRADE OF

TAILORING AND GARMENT MAKING

BY

DIRECTORATE OF INDUSTRIES

ANDAMAN AND NICOBAR ADMINISTRATION

MONTH THEORY PRACTICAL

1st Adventure of sewing machine and importance of Tailoring in Daily Life and its commercial values

Theoretical knowledge on Operation of Sewing machine

o Hand sewing machine, o Tradle sewing machine o Electric sewing machine.

Various types of hand stitches Preparation of fair Theory & Drafting

files.

Introduction for using of sewing machine.

Practice – How to operate the sewing machine.

Knowledge of sewing machine parts and its functions.

Maintenance and oiling of machinery. Basic hand stitches - Hemming stitch,

Back stitch, Half back stitch, Even stitch, Uneven stitch, Running stitch etc.

Hand Embroidery stitches – Hearing bone stitch , fish bone stitch, shadow stitch, whipped chain stitch, bullion stitch etc.

2nd Theoretical knowledge on Sewing Machine and its parts -

o Balance wheel, spool pin, pressure foot, needle bar, pressure foot lifter, feed dog , stitch regulator etc.

Various kinds of Hand Embroidery stitches –

Kinds of Basic seams and its applications

Difference between Inches & cms. Preparation of fair Practical files.

Basic seams – Plain seam, French seam, flat seam, zig-zag seam, Bound seam, self bound seam, pinked seam etc.

Demonstration and Practice – How to take Upper and lower body measurement

Demonstration & practice of Drafting, Paper cutting & stitch practice of various sample garments

Requirement & method of cutting cloth as per measurement.

Method of taking measurement of body calculation

3rd Description of Tools & Equipment –

(i) Measuring tools & equipment (ii) Drafting tools & equipment (iii) Cutting tools & equipment (iv) Sewing tools & equipment (v) Pressing tools & equipment

Some more Hand Embroidery stitches –

Double chain stitch, stem stitch, Bullion

laisy-daisy stitch, Blanket stitch, Button

stitch, semi running stitch, Gujrati

stitch etc.

Paper pattern and lay out on the cloths

and complete these by applying different

2. Abbreviations on Drafting 3. Drafting method of upper &

lower body garment. Drafting & paper pattern of saree

petticoat, Gents kurta & pajama, etc.

4. 1st terminal test for theory. (MM 25)

style of stitches.

Stitch & Hand Embroidery work on

Pillow cover etc.

Basic Neck lines & Piping neck lines-

Demonstration of petticoats

o 1st Terminal test for Practical.

(MM 25)

4 th Drafting of child body block

Drafting & paper pattern of different types of collars-

Maintenance of sewing machine

Cleaning & oiling of sewing machine -

Renovation of Cloths- Darning by hand machine, darning patching

Drafting & paper pattern of Kids wear - Baby frock, ‘A’ Line skirt, straight skirt, tight skirt , half circular skirt, full circular skirt, novelty skirt etc.

Measurement chart- o Measurement chart for kids ,

Ladies & Gents.

Designing of Box pleat skirt, Inverted pleat skirt, Designer skirts, baby frock and baby tops etc.

Designing of Kids wear - like Baby frock, ‘A’ Line skirt, straight skirt, tight skirt, half circular skirt, full circular skirt, novelty skirt etc.

5th Different types of pleats-

Different types of tucks

Drafting & Paper pattern of different types sleeves – plain sleeve, puff sleeve, flair sleeve, Magyar sleeve, kimono sleeve etc.

Drafting & paper cutting of Ladies kurties , suit, frock suit etc.

How to take measurement –full length, shoulder, chest round, waist round, hip round, seat, ankle round, sleeve length, color etc.

Cutting & stitching for designer Ladies kurties , suit, frock suit etc. of different sizes

Demonstration of various types of tucks

Demonstration and making samples of knitting work and crochet work with wool and lace

6th Sewing needles and threads – o Various kinds Hand needle and

Machine needle available and its applications

Functions and operations of various Machine attachment parts

Drafting & paper pattern of plain salwar, kalidar salwar, patiyala, ladies kurtis etc.

1. 2nd terminal test for theory. (MM 25)

Demonstration of machine coaching stitch , shell stitch and form stitch and making of related samples

Demo of Cutting & stitching of plain salwar, kalidar salwar, chudidar salwar etc. and making of related samples

2nd terminal test for Practical. (MM 25)

7th Theoretical knowledge on Textile Designing – Block print , spray print, vegetable print, stencil printing, fabric

Practical Demonstration of Textile Designing in various kinds of cloths and fabrics–

print etc. Including Tie & dye

(i)Block print . (ii) spray print, (iii) vegetable print. (iv) stencil printing.

(vi) fabric print etc. (vii) Tie and dye etc.

8th Sewing machine faults and their rectification:-

Different patterns of design – o Vertical pattern, horizontal

pattern, diagonal pattern, asymmetrical pattern

o Brick pattern etc.

Design development and Demonstrations of designer dresses

Using shell, beads and other accessories

Project work -

Creating individual designer samples with fusion of shells, beads tec.

9th Drafting & paper pattern of apron feed `er, plain blouse, six cut blouse, back hook blouse

Drafting & paper pattern of night gown, night dress, house coat

3rd terminal test for theory. (MM 25)

Cutting and stitching of apron, feeder, plain blouse, six cut blouse, back hook blouse etc.

Cutting and stitching of designer night gown and housecoat.

3rd terminal test for practical. (MM 25)

10th Study of different types of human body

Principle s of paper pattern making

Drafting & paper pattern of Half pant, Half sleeve shirt.

Drafting & paper pattern of Full pant and full sleeve shirt.

Cutting & stitching of Half pant and Half sleeve shirt.

Cutting & stitching of full pant and full sleeve shirt.

11th Removal of stains –

Stain of machine oil, tea stain, ink stain ,ghee stain, boot polish stain, blood stain etc.

Information on Dictionary of tailoring

How to Handle fashion maker and advanced sewing machines.

Market survey on various kinds of fabrics

12th Revision of the course studies during the session.

Correction of theory and drafting files.

Conducting final theory test by instructress.

Presentation in Practical records and final touch to all the practical works conducted during the entire session.

Marking of practical records

Final practical test by Instructress .

As approved by:-

A&N Administration

Port Blair

Issued by:-

Directorate of Industries

A&N Administration

Port Blair

SYLLABUS OF ONE YEAR CONVENTIONAL COURSE

FOR THE TRADE OF

CANE AND BAMBOO HANDICRAFTS

BY

DIRECTORATE OF INDUSTRIES

ANDAMAN AND NICOBAR ADMINISTRATION COURSE CONTENTS

Theory Practical

1st Month

Introduction of Cane & Bamboo for its used and identification of different type of Cane & Bamboo available in Andaman & Nicobar Islands and study of catalogue and design for making of furniture and Handicrafts.

Description of Bamboo and its used to production of Handicrafts and furniture.

Practical/ Hands on works experience under the guidance of Instructor/worker:-

Cane & Bamboo strips processing and making or extension of Bamboo and Cane strips.

Cane knitting on the chair, chatai (Mat] and Bamboo knitting on the different type of chatai (Mat].

2nd and 3rd Month

Introduction about the tools and machinery used in the Cane & Bamboo Handicrafts and furniture and own safety measures to be adopted while working with the tools and machinery with drawing for tools.

Introduction and description of different type of tools use for production of Cane and Bamboo Handicrafts and furniture.

Practice of Cane joint making of different type and different type of Cane binding for handicraft and furniture.

Manufacturing of different type of Handicraft and furniture.

Manufacturing of different type of Handicraft and decorative items and furniture for Cane and Bamboo.

Preparation of products independently without assistance from instructor workers under overall supervision of Instructor and made for job and estimate.

4th and 5th month

Different treatment used to processing Cane & Bamboo.

Bending of Cane & Bamboo method of different shapes

Preservation of Bamboo

Use of Borax & Boric Acid, use of Smoke chamber and other Chemical Process. Practice of Traditional

for use of furniture and Handicraft items.

Coloring, painting, varnishing on Cane & Bamboo items, Brush painting and spray painting etc.

Finishing of Cane & Bamboo surface of furniture and Handicraft before painting and varnishing.

Estimating and noting of finished products.

process

Practice of dying utilizing various chemical & vegetative dyes.

Preparation of products independently without assistance from instructor workers under overall supervision of Instructor and made for job and estimate

How to behave with customer as

entrepreneur

Communication skills that are useful

to customer service are identify in

accordance with enterprises

requirements.(speaking, giving

information, active listening)

6th and 7th Month

Joints: Briefing about various joints, method of joints, uses of joints.

Introduction: Use of various Household and Public furniture, Advantage of sketch making of various furniture designs

Brief description of electric Drill

Machine and how to operate trouble

shooting of this machines

Brief description of 2 side/4 side

planer machine and how to operate

trouble shooting of this machine`

Joints

Practice in tongue and groove or male and female joint, Bolt fastening joint. Overlapping joint, U-shape joint. Horizontal joint, Vertical joint etc.

Types of Furniture

Demo of various type of furniture, Draw the Neat sketch of furniture

Drill Machine

Practice of operation in electric drill

machine, oiling and lubrication of

machine

Practice of operation in 2 side/4 side

machine planer, oiling and lubrication

of machine including preventive

maintenance

8th and 9th Month

How to make pattern, banding, buffing, and polishing of bamboo.

Various joineries used in furniture making process

Use of Blow lamp

Practice of pattern making, use of blow lamp and it precaution.

Practice of furniture making

Fusion of coconut, shell and bamboo handicrafts

Calculation of cost of finished Bamboo.

11th Month

Project Work

Industrial visits

Preparation of individual items

12th month

Exposure training in registered cane units with updated machines Industrial Visit

Examination

As approved by:- A&N Administration Port Blair

Issued by:- Directorate of Industries A&N Administration Port Blair