SXSS Submersible Slurry Pump Manual - Price Pumps Australia
Transcript of SXSS Submersible Slurry Pump Manual - Price Pumps Australia
Price Pumps Australia Phone: +61 7 49985070 Mob 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 1
Model: PPHSS Heavy Duty Submersible Slurry Pump
Operation Manual
ABN 17 154 031 802 21 Ginger St, Paget Mackay Qld Australia 4740
PO Box 5709, Mackay Mail Centre Qld Australia 4741
Ph: +61 07 4998 5070 Fax: +61 07 4952 1944
Mobile: +61 0409 827 290
Email: [email protected]
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 2
CONTENTS
Section 1 - Basic Information
1.1 General Introduction 3
1.2 Model Identification 3
1.3 Operating Conditions 3
1.4 Safety Precautions 4
1.5 Pump Model Information 5
Section 2 - Installation
2.1 Pre-installation Checks 11
2.2 Installation and Cable Connection 11
2.3 Assembly and Disassemble Procedure 12
Section 3 - Operation & Maintenance
3.1 Care and Maintenance for Long Term 13
3.2 Troubleshooting 14
Section 4 - Spare Parts
4.1 Parts List 15
4.2 Recommended Spares 16
Section 5 - Dimensions
5.1 Dimensional Data 16
Section 6 - Drawings
6.1 Installation Drawings 19
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 3
Section 1 – Basic Information
1.1 General Introduction
The Price Pumps Australia Electro Submersible Slurry pump range is a versatile pump designed
for Mining and Civil applications where the water is contaminated with suspended solids. I.e. Coal
fines, sand and mud. The pumps have been designed to maximise service life, through lower
RPM, coupled with the hydraulic design the lower pump speed also benefits the service life of
critical parts, mechanical seals, and bearings. The wet end components are manufactured from
materials designed for high abrasion. Giving superior service life, this coupled with an extra-large
hydraulic passage allows larger particles to pass. The motor is protected by a superior double
mechanical seal and probes to detect water ingress into the mechanical sea oil chamber. The wet
end is fitted with an integrated agitator, come breaker; this will ensure that only particles of the
correct size enter the chamber, plus creating adequate flow turbulence to keep suspended solids
flowing.
1.2 Model Identification
PPHSS 200 - 15 - 22 J L
1.3 Operating Conditions
1. Power Source:
Voltage: 380V/415V/1000V Frequency: 50Hz/60Hz Three Phase
2. Water Temperature: 40°C Max
3. Not suitable for flammable or explosive working conditions.
4. Max volume ratio no more than 30% in water, S.G of medium less than 1.2kg/L.
5. The maximum depth of submergence should be less than 20 meters. The motor should be
totally submerged at all times during operation.
6. pH of liquid: 4 ~ 10 range
7. Recommended installation is vertical.
8. Operating conditions: S1
With Cooling Jacket
With Agitator
Motor Power: 22kW
Rated Head
Rated Capacity
Type: Heavy Duty Submersible Slurry Pump
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 4
1.4 Safety Precautions
1. The Electro-Submersible pump is a heavy duty product, and as such must be handled with
complete care and attention to safe work practices and established in house procedures. Failure
to do so may result in equipment damage or personal injury.
2. Each pump is fitted with an ID tag; please make sure the pump to be installed meets the duty
point requirements.
3. Check the weight of the unit, and make sure you have the correct equipment and adequate
lifting capacity before attempting to lift the pump.
4. To correctly lift the pump use the lifting bracket fitted to the top of the pump.
5. Do not lift with the electrical or control cables, as this could cause damage to the connections,
with possible fatal results.
6. Make sure you have allowed sufficient cable free play at cable entry points. Do not place any
load on the electrical cables. Tie them off to the security cable with enough free play facilitating
movement around cable entry points.
7. Ensure that all electrical connections are carried out by a suitably qualified Electrician and that
all checks are carried out and documented prior to start up.
8. Bump start only to establish correct rotation.
9. If you have a model requiring cooling water or water system connections make sure these are
filled, connected and/or flushed prior to start up. Make sure you have adequate flow available.
10. Avoid any preload on the pump discharge flange and pipe work by adequately securing all
discharge pipe work.
a. Make sure that the security cable/chain has sufficient capacity to support the pump during
removal from service.
b. Use PPE and protect your eyes from possible splash during the removal and wash down of the
pump.
c. After removal ensure the pump is supported and held securely during transport.
d. Do not store the pump without complete cleaning and protecting exposed surfaces with a
suitable protective covering of Oil or defence yellow rust inhibitor.
11. Always work safely and remember, if you are working with an assistant, look after their welfare
also.
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 5
1.5 Pump Model Information
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff. (%)
Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS30-30-7.5 80 7.5 1460 43 13
24 31
30 30
36 29
PPHSS50-21-11 100 11 1460 48 21
35 22
50 21
60 20
PPHSS50-26-22 80 11 1460 48 13
35 29
50 26
60 24
PPHSS100-18-11 100 11 1460 55 21
70 20
100 18
120 15
PPHSS25-40-15 80 15 1460 35 13
18 41
25 40
30 39
PPHSS50-35-15 100 15 1460 47 13
35 38
50 35
60 32
PPHSS60-30-15 100 15 1460 50 13
42 33
60 30
72 27
PPHSS75-25-15 100 15 1460 51 13
52 28
75 25
90 22
PPHSS150-50-15 150 15 1460 56 21
105 17
150 15
180 13
PPHSS75-35-22 100 22 980 48 13
52 38
75 35
90 32
PPHSS75-45-22 100 22 980 48 13
52 48
75 45
90 42
PPHSS100-25-22 100 22 980 55 14
70 27
100 25
120 22
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 6
1.5 Pump Model Information Cont.
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff. (%)
Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS150-22-22 150 22 980 60 32
105 25
150 22
180 20
PPHSS200-15-22 150 22 980 60 45
140 17
200 15
240 13.5
PPHSS100-35-30 100 30 980 50 21
70 38
100 35
120 31
PPHSS150-30-30 150 30 980 50 21
105 33
150 30
180 26
PPHSS200-25-30 150 30 980 51 25
140 28
200 25
240 21
PPHSS250-20-30 150 30 980 60 25
175 23
250 20
300 18
PPHSS100-45-37 100 37 980 43 21
70 48
100 45
120 42
PPHSS100-50-37 100 37 980 43 13
70 53
100 50
120 47
PPHSS300-20-37 150 37 980 58 28
240 22
300 20
360 17
PPHSS100-60-45 100 45 980 43 13
70 64
100 60
120 55
PPHSS-200-30-45 150 45 980 53 25
140 33
200 30
240 27
PPHSS-150-45-55 150 55 980 50 21
105 47
150 45
180 42
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 7
1.5 Pump Model Information Cont.
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff.(%) Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS250-35-55 150 55 980 53 36
175 38
250 35
300 33
PPHSS300-30-55 150 55 980 55 36
210 34
300 30
360 26
PPHSS600-15-55 250 55 980 62 32
420 18
600 15
720 11
PPHSS150-55-75 150 75 980 48 15
105 58
150 55
180 51
PPHSS150-60-75 150 75 980 48 15
105 63
150 60
180 56
PPHSS200-45-75 150 75 980 52 18
140 48
200 45
240 41
PPHSS200-55-75 150 75 980 50 18
140 58
200 55
240 51
PPHSS350-35-75 200 75 980 60 29
245 78
350 75
420 71
PPHSS400-25-75 200 75 980 62 29
280 29
400 25
480 23
PPHSS200-60-90 150 90 980 50 14
140 63
200 60
240 57
PPHSS250-55-90 150 90 980 50 14
170 58
250 55
300 52
PPHSS300-45-90 150 90 980 52 25
210 50
300 45
360 39
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 8
1.5 Pump Model Information Cont.
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff.(%) Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS300-50-90 150 90 980 52 25
210 54
300 50
360 45
PPHSS400-40-90 200 90 980 53 25
280 44
400 40
480 36
PPHSS500-25-90 200 90 980 65 25
350 30
500 25
600 20
PPHSS450-30-90 200 90 980 64 25
315 34
450 30
540 25
PPHSS250-60-110 150 110 980 54 18
175 64
250 60
300 55
PPHSS300-60-110 150 110 980 55 18
210 64
300 60
360 56
PPHSS400-50-110 200 110 980 56 28
280 54
400 50
480 45
PPHSS500-35-110 200 110 980 61 32
350 38
500 35
600 31
PPHSS600-30-110 250 110 980 64 35
420 33
600 30
720 26
PPHSS800-25-110 300 110 980 66 50
560 28
800 25
960 21
PPHSS1000-18-110 300 110 980 68 50
700 22
1000 18
1200 13
PPHSS780-26-110 300 110 980 68 50
545 29
780 26
935 22
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 9
1.5 Pump Model Information Cont.
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff.(%) Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS400-60-132 200 132 980 68 28
280 64
400 60
480 55
PPHSS500-45-132 200 132 980 67 28
350 49
500 45
600 42
PPHSS500-55-132 200 132 980 70 28
350 59
500 55
600 52
PPHSS800-35-132 300 132 980 70 42
560 38
800 35
960 32
PPHSS1000-22-132 300 132 980 71 50
700 27
1000 22
1200 17
PPHSS1250-15-132 300 132 980 70 56
875 18
1250 15
1500 12
PPHSS600-50-160 200 160 980 65 28
420 56
600 50
720 43
PPHSS650-52-160 200 160 980 65 28
455 56
650 52
780 44
PPHSS1250-25-160 350 160 980 70 56
875 28
1250 25
1500 22
PPHSS1000-30-160 300 160 980 70 53
700 34
1000 30
1200 25
PPHSS1750-15-185 350 185 980 70 56
1225 19
1750 15
2100 10
PPHSS600-55-200 250 200 980 62 28
420 59
600 55
720 50
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 10
1.5 Pump Model Information Cont.
Model Outlet
Dia. (mm) Motor Power
(KW) Speed (r/min)
Eff.(%) Max Solids Dia (mm)
Capacity (m3/hr)
Head (m)
PPHSS800-45-200 300 200 980 66 42
560 49
800 45
960 40
PPHSS1000-40-200 300 200 980 70 42
700 45
1000 40
1200 35
PPHSS1500-20-200 350 200 980 71 56
1050 24
1500 20
1800 15
PPHSS2000-20-200 400 200 980 72 56
1400 25
2000 26
2400 14
PPHSS800-55-220 300 220 980 66 38
560 60
800 55
960 50
PPHSS1250-35-220 350 220 980 70 45
875 39
1250 35
1500 30
PPHSS1000-50-250 300 250 980 68 45
700 55
1000 50
1200 45
PPHSS1500-35-250 350 250 980 72 50
1050 40
1500 35
1800 30
PPHSS1750-30-250 350 250 980 70 55
1225 34
1750 30
2100 25
PPHSS1500-40-280 350 280 980 70 50
1050 45
1500 40
1800 35
PPHSS1750-40-315 350 315 980 70 55
1225 45
1750 40
2100 35
PPHSS2000-35-315 400 315 980 72 60
1400 40
2000 35
2400 30
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 11
Section 2 – Installation
2.1 Pre-Installation Checks
a. Make sure the pump is suited to the operational conditions for which it is to be
used.
b. Duty Points should not exceed the pumps BEP range by more than 1.2 times its
rated capacity.
c. Thoroughly check the equipment for loose fasteners and damage to the electrical
cable during transport.
d. Check pump ID plate details against the installed electrical overload protection
devices.
e. Check the oil level in the oil cavity before starting the pump. Use only turbine oil
and fill to the bottom of the oil fill port, with the pump standing upright. Caltex Regal
R&O 32.
f. If the pump is fitted with the clean water cooling jacket, clean water must flow at all
times.
NB.
Entry through the bottom port. Discharge through the top port. Refer to FIG. No 3.
2.2 Installation and Cable Connection
a. Winding Insulation resistance should be 50Mega Ohms or above at 500Volts on
the ohmmeter. The power cable is 4 cores. Three of them are power lines marked U,
V, W. Earth is marked all pumps fitted with control cables are marked as listed
below.
Connect all cables to the control box by following the above detail.
Name
Mark
Core Name
Core Function
Cable
Length
Insulation Resistance Between
Line & Earth Line
Power Cable
U, V, W
Three phase power Power line
10m
∞ Earth Connection to earth
Control Cable
WC
Thermal sensor Connection to thermal
sensor 0
YS
Oil-water sensor Connection to oil- water
sensor
∞
XL Water leakage
switch Connection to float
Switch
JS Water sensor Connection to oil- water
sensor
ZC Bearing
temperature sensor Connection to thermal
sensor 0
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 12
b. Check the insulation resistance during installation, resistance between motor
winding and earth should not be less than 5 mega ohms when submerged.
c. Check motor direction prior to installation.
NB
This manual is generic. If your unit does not match this manual, please
contact your supplier for relevant information.
2.3 Assembly and Disassembly Procedure
a. Start with the oil housing firmly placed on a suitably stable work bench.
Remember this is a heavy component and safe work practices must be followed.
b. Place the housing O-ring seal around the locating lip, on the top side of the
bearing housing. Then gently place the rotor into position, and then place the
stator over the rotor.
c. With the rotor and stator in place, fit the motor cover and bolt it into position. Fit
the cable assembly plate to the motor cover, fit the cable sleeve and lock tabs,
with everything in place and secure fit the hanger bracket.
d. Turn the motor assembly upside down and secure properly, making sure it is safe
and accessible to continue the assembly.
e. Fit the mechanical seal upper casing cover and mechanical seal seat.
f. Gently fit the shaft sleeve and set the seal, then the oil seal, this then completes
the motor assembly.
g. Fit the back cover plate and key; slide the impeller onto the shaft. Fit the outer
casing seal ring and then the outer casing. Secure the impeller into position using
the impeller cap.
h. Fit the front cover plate into position and secure.
i. Fit the kick stand over the front cover plate and secure it and the
impeller hub cap.
j. Fit the rubber ring, agitator and base plate.
To make disassembly easier when service is required, follow these steps in
reverse, as there is no other method without causing damage to the critical
components.
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 13
Section 3 – Operation & Maintenance
3.1 Care and Maintenance for Long Term Storage
1. If the pump is to be stored for any length of time, thoroughly clean the unit
removing any matter that could be corrosive and flush with clean water. Coat all
exposed wet end components with Defence Yellow or an equivalent rust inhibitor.
Store pump in a dry area.
2. The following items must be inspected after long periods of continuous running or
at 2500 hours.
a. Check and tighten loose fasteners
b. Check the mechanical seal for leaks
c. Drain and replace the oil in the oil chamber
d. Replace mechanical seal if excessively worn
3. The following must be observed after 12 months service or less depending on the
abrasive nature of the medium being pumped.
a. Impeller
b. Back cover plate
c. Front cover plate
d. Volute
e. Agitator
f. Oil seal
4. Pressure test the motor housing and mechanical seal oil chamber using
compressed air to 30PSI for 5 minutes.
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 14
3.2 Trouble Shooting
Fault Possible Cause Suggested Remedies
Over current
1. Impeller flow restricted 1. Check and clear impeller
2. Actual capacity more than
120% of rated capacity 2. Adjust the valve or use large
pump.
3. Pumped liquid is high
density or viscosity
3. Reduce density or viscosity
4. Operating voltage is too low 4. Use rated voltage
5. Cooling system has
insufficient flow
5. Clean cooling system
6. Bearing failure 6. Replace bearings
(determine cause)
Cannot start the motor and motor is
buzzing
1. Operating voltage is too low 1. Use rated voltage
2. Single phase operating 2. Check power source
3. Impeller is blocked 3. Check and clear impeller
4. Binding between the impeller
and lower casing cover or inner
cover
4. Adjust the clearance of
impeller
Cannot reach rated capacity
or no flow
1. Wrong rotation 1. Exchange connection of any
two power terminals
2. Blockage in impeller 2. Check and clear impeller
3. Inlet not fully submerged 3. Reset the pump depth
4. Delivery pipe leaking or
blocked
4. Renew the pipe or clean it.
5. Actual head too high 5. Select suitable pump for
application
Motor resistance less than
0.5MΩ
1. Cable junction damaged 1. Make connection again
2. Stator winding is damaged 2. Replace winding
3. The winding is wet 3. Find cause and rectify. Dry out
windings
4. Cable is damaged 4. Renew cable
Excessive noise and vibration
1. Damaged or work impeller 1. Replace the impeller
2. Blocked volute 2. Clean the blockage
3. Bearing failure 3. Replace the bearing
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 15
Section 4 – Spare Parts
4.1 Parts List
Item Description Qty Material Item Description Qty Material
1 Base plate assembly 1 Fabricated steel 18 Oil seal 1 B150X180X15-D
2 Inlet bracket 1 Cast iron GG20 19 Upper bearing cover 1 Cast iron GG20
3 Pump casing 1 W105 20 Rotor 1
4 Suction board 1 W105 21 Lower bearing cover 1 Cast iron GG20
5 Impeller 1 W105 22 Bearing temperature sensor
1 PT100
6 Oil house cover 1 Cast iron GG20 23 Oil-water sensor 1
7 JSFS-A float switch 1 24 Oil housing 1 Cast iron GG20
8 Bearing 6322 1 25 Pump inner cover 1 W105
9 Bearing 7324B/DT 1 26 Hub 1 Ductile cast iron
10 Stator 1 27 Strainer 1 420 Stainless steel
11 Shaft sleave 1 420 Stainless steel
28 Agitator 1 W105
12 Bearing NU322E 1 29 Winding thermal sensor 1 PT100
13 Leaving ring 1 Steel 30 Water sensor 1
14 Power cable assembly 2 31 Winding thermal switch 3 Thermal relay
15 Control cable assembly
1 32 Upper mechanical seal 1
16 Cable cover 1 Cast iron GG20 33 Lower mechanical seal 1
17 Motor cover 1 Cast iron GG20 34 Cooling jacket 1 Fabricated steel
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 16
4.2 Recommended Spare Parts for 2 years Operation
Section 5 - Dimensions
5.1 Dimensional Data
Item Name Qty Material
1 Casing 1 W105
2 Impeller 1 W105
3 Agitator 1 W105
4 Inner casing cover 1 W105
5 Lower casing cover 1 W105
6 Mechanical seal 1 Set
7 Oil seal 1 Set
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 17
5.1 Dimensional Data Cont.
Model A (mm) B (mm) C (mm) D (mm) L (mm) L1 (mm) L2 (mm)
PPHSS30-30-7.5 605 390 396 80 842 700 296
PPHSS50-21-11 606 406 405 100 913 738 300
PPHSS50-26-11 605 390 396 80 889 720 296
PPHSS100-18-11 606 406 405 100 913 738 300
PPHSS25-40-15 673 440 435 80 950 774 290
PPHSS50-35-15 632 385 422 100 950 774 290
PPHSS60-30-15 632 385 422 100 950 774 290
PPHSS75-25-15 606 406 405 100 950 774 300
PPHSS150-15-15 620 410 455 150 990 814 340
PPHSS75-35-22 925 650 505 100 1370 1105 502
PPHSS75-45-22 925 650 505 100 1370 1105 502
PPHSS100-25-22 883 630 545 100 1401 1135 353
PPHSS150-22-22 883 630 568 150 1401 1135 353
PPHSS200-15-22 870 630 551 150 1375 1110 507
PPHSS100-35-30 832 630 605 100 1452 1144 425
PPHSS150-30-30 832 630 605 150 1452 1144 425
PPHSS200-25-30 835 630 605 150 1460 1148 469
PPHSS250-20-30 835 630 605 150 1460 1148 469
PPHSS100-45-37 950 650 640 100 1560 1170 485
PPHSS100-50-37 950 650 640 100 1560 1170 485
PPHSS300-20-37 1070 595 775 150 1567 1170 510
PPHSS100-60-45 1050 680 665 100 1670 1230 495
PPHSS200-30-45 1006 665 650 150 1699 1255 495
PPHSS150-45-55 1011 678 640 150 1692 1248 488
PPHSS250-35-55 1006 665 650 150 1699 1255 495
PPHSS300-30-55 1006 665 650 150 1699 1255 495
PPHSS600-15-55 1052 711 675 250 1720 1275 515
PPHSS150-55-75 1115 800 715 150 1835 1380 482
PPHSS150-60-75 1115 800 715 150 1835 1380 482
PPHSS200-45-75 1011 678 640 150 1904 1425 488
PPHSS200-55-75 1115 800 715 150 1835 1380 482
PPHSS350-35-75 1332 690 947 200 1883 1404 485
PPHSS400-25-75 1422 665 1047 200 1888 1410 485
PPHSS200-60-90 1115 800 715 150 1835 1380 482
PPHSS200-55-90 1115 800 715 150 1835 1380 482
PPHSS300-45-90 1115 800 715 150 1883 1380 482
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 18
5.1 Dimensional Data Cont.
Model A (mm) B (mm) C (mm) D (mm) L (mm) L1 (mm) L2 (mm)
PPHSS300-50-90 1540 849 1110 150 1922 1420 490
PPHSS400-40-90 1580 850 1150 200 1940 1430 500
PPHSS500-25-90 1422 665 1047 200 1888 1410 485
PPHSS450-30-90 1422 665 1047 200 1888 1410 485
PPHSS250-60-110 1115 800 715 150 2203 1527 485
PPHSS300-60-110 1115 800 715 150 2203 1527 485
PPHSS400-50-110 1190 760 790 200 2225 1550 500
PPHSS500-35-110 1180 750 1020 200 2245 1570 520
PPHSS600-30-110 1180 750 1020 250 2245 1570 520
PPHSS800-25-110 1640 854 1207 300 2407 1725 626
PPHSS1000-18-110 1640 854 1207 300 2407 1725 626
PPHSS780-26-110 1640 854 1207 300 2407 1725 626
PPHSS400-60-132 1540 849 1117 200 2328 1665 520
PPHSS500-45-132 1124 823 739 200 2320 1656 472
PPHSS500-55-132 1124 823 739 200 2320 1656 472
PPHSS800-35-132 1581 802 1177 300 2538 1784 601
PPHSS1000-22-132 1640 854 1207 300 2465 1801 626
PPHSS1250-15-132 1581 802 1177 300 2538 1784 601
PPHSS600-50-160 1124 823 739 200 2673 1772 472
PPHSS650-52-160 1124 823 739 200 2673 1772 472
PPHSS1250-25-160 1600 820 1180 350 2890 1990 672
PPHSS1000-30-160 1581 802 1177 300 2891 2137 601
PPHSS1750-15-185 1660 820 1260 350 2900 2140 652
PPHSS600-55-200 1140 823 739 250 2673 1772 472
PPHSS800-45-200 1686 900 1229 300 2934 1993 710
PPHSS1000-40-200 1686 900 1229 300 2934 1993 710
PPHSS1500-20-200 1770 870 1850 350 3060 2049 672
PPHSS2000-20-200 1880 870 1896 400 3060 2049 672
PPHSS800-55-220 1686 900 1229 300 2934 1993 710
PPHSS1250-35-220 2150 977 1630 350 2922 2021 730
PPHSS1000-50-250 2250 9987 1730 300 2980 2081 710
PPHSS1500-35-250 2150 977 1630 350 3012 2111 730
PPHSS1750-30-250 2150 977 1630 350 3012 2111 730
PPHSS1500-40-280 2250 9987 1730 350 3058 2159 710
PPHSS1750-40-315 2180 1026 1650 350 3235 2261 804
PPHSS2000-35-315 2260 1026 1730 400 3235 2261 804
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 19
Section 6 - Drawings
6.1 Installation Drawings
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 20
Heavy Duty Pumps For Mining and Industry
Price Pumps Australia
Phone: +61 7 49985070 Mob +61 0409 827 290 [email protected] www.pricepumpsaustralia.com.au Page 21
21 Ginger St, Paget Mackay Qld Australia 4740 PO Box 5709, Mackay MC Qld Australia 4741
Ph: +61 07 4998 5070 Fax: +61 07 4952 1944
Email: [email protected]
ABN 17 154 031 802
As Price Pumps Australia’s policy is one of constant improvement, we reserve the right to make specification changes without notice and without incurring liability