Switchgear Instruction Manual 1 Version 1 4 (2)

Issue Date

4 May 2010Version Number

Version 1.4

Networks

License Grant.Artefact Systems (Australia) Pty Ltd hereby grants Western Power a non-exclusive, non-transferable right to use one copy of this version of the Western Power Switchgear InstructionManual 1 Version 1.4 - Issue Date 4 May 2010. You may install one copy of the CD on one computer / workstation for which the CD was designed.The CD and documentation are protected by copyright law and remain the intellectual property of Artefact Systems (Australia) Pty Ltd.Artefact Systems (Australia) Pty Ltd. is not responsible for any damage to the user's computer system or data and in no event will Artefact Systems (Australia) Pty Ltd., its officers, directors, employees or agents be responsible to the user for any consequential, incidental, or indirect damages (including damages for loss of business profits, business interruption, loss of business information and the like) arising out of the use or inability to use the Artefact Systems (Australia) Pty Ltd. CD.

This Document Is Uncontrolled When Printed

Document Number PSC/80/3(78)V1 Network Switchgear Instruction Manual Design Artefact Systems Pty Ltd.

Date Issued: 4 May 2010Doc Ref: WPWorkProcedure1

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1WORK PROCEDURE INSTRUCTIONS

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

WO

RK

PR

OC

ED

UR

E IN

ST

RU

CT

ION

S

1 of 2

The following information is the 'Western Power Work Procedure Instructions' for the use of this Network Switchgear Instruction Manual 1

Please refer to the How To Use This Manual template for further details on how to use this Network Switchgear Instruction Manual 1

The responsibility for safe working with electrical switchgear rests with the employer, employees, and contractors required to operate the different types of switchgear that exists on the Western Power network.

The purpose of this manual is to provide a common set of operating instructions for electrical switchgear. The intent is to provide a consistent understanding of switchgear operating requirements and promote the safe and efficient operation of switchgear. This can reduce the likelihood of personal injury, equipment damage and loss of supply.

This manual is a physical operating guide only, and does not contain all of the technical details, system protection requirements, and operational checks that are required for safe operation of the network. This manual must be used in conjunction with the Western Power's Electrical Safety Code, Switching Operators Manuals, Network Operating Instructions, Field Instructions, the Job Risk Assessment process - and remember to Switch On Mate .

When access or switching is required on the electrical network for ANY PURPOSE the Control Centre MUST be advised prior to the operation starting, and at the completion of the operation.

Persons operating the equipment contained in this Manual must be appropriately trained and authorised by Western Power as per NOI 04-13. They should also ensure operating equipment is in good order and wear and use the correct protective apparel.

The equipment covered in this Manual is not exhaustive and there are items of equipment that have not yet been included. Whilst every effort has been made to ensure accuracy all users are encouraged to report any errors inaccuracies or omissions found while using the manual as a guide. If an amendment is required on an item of equipment or a new template is required for equipment not yet contained in this manual, contact your representative on the Operations Policy and Practices Committee or the Manager Network Operations - Network Operations Control Centre.

Arrangements will be made for the photography and text to be compiled to enable new templates to be made and distributed. This manual is a controlled document. When there are modifications or additions to this manual the modified or new templates will be replaced and a new index issued and dated accordingly.

It is the switching operators responsibility to operate only within their authorised levels.Attention

onsibility for safe working with electrical switchgear rests with th

Western Power

Network Switchgear Instruction Manual 1

Document Number PSC/80/3(78)V1




Date Issued: 4 May 2010 Doc Ref: WPWorkProcedure2

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

WO

RK

PR

OC

ED

UR

E IN

ST

RU

CT

ION

SNETWORK SWITCHGEAR INSTRUCTION MANUAL 1

WORK PROCEDURE INSTRUCTIONS

2 of 2

'A3' DX & N, Combination of restrictions

'D' Under Direction

'DN' Under Direct, EXCL Comm of RMU

'DX' Under Direct, EXCL Earthing

'R' Excludes switching on Regulators

'N' Excludes Commissioning of Ring Main Switchgear

'NX' Excludes Earthing & Comm of RMU

'S' Excludes writing and checking of switching programs

'X' Excludes Earthing

'Z' Authority Suspended

'G' Gas Insulated Transmission Switchgear

Switching Level Levels Include

1 All LV O/H systems including Distribution HV from drop-outs to transformers

2 All O/H apparatus including Reclosers, Sectionalisers, Regulators,

Capacitors and Ground mounted transformers.

3 Distribution HV O/H to U/G systems (ie. aerial to RMU )

4 LV underground systems

5 Distribution HV underground RMU to RMU

6 Operation of Distribution HV feeders from Zone Substations including

protection by-pass, transformer paralleling and transfer bus.

7 Transmission circuits from Zone Substations.

8 All apparatus within a Zone Substation.

9 Transmission circuits into Zone Substations.

10 All Terminal Substation apparatus.

11 Control Room operations including switching schedule preparation (NOCC).

12 Control Room operations including switching schedule preparation (SOCC).

SWITCHING AUTHORITIES AND COMPETENCY (Ref NOI 04-13)

AUTHORITY RESTRICTIONS

Operation Options

Special Notes

Ensure the switchgear is fit for service prior to and after operation.

Note: The transformer fuse switch has a different operating mechanism to the circuit switch.

Caution


Date Issued: 2 March 2006Doc Ref: WPAlstomFBX1

OpeningClosingEarthingHV FusesSpring Charge

3322116.6

33022013266

Manufacturer:Model:Rating:

Break Rating:Insulant:

AlstomFBX630 Amps16 KASF6

ALSTOMFBX

AL

ST

OM

FB

X

1 of 2

Voltage KV

OperationClosing the Circuit Switch

Special Notes

Confirm the circuit switch location and labeling prior to operation.

Special Notes

1. Unlock if required and insert the operating handle into the open / close operating mechanism.2. Rotate the operating handle CW to the stop position to close the circuit switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the circuit switch status.

OperationOpening the Circuit Switch

1. Unlock if required and insert the operating handle into the open / close operating mechanism.2. Rotate the operating handle ACW to the stop position to open the circuit switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the circuit switch status.

Special Notes

Confirm the transformer fuse switch location and labeling prior to operation.


Operation

Closing the Transformer Fuse Switch1. Unlock if required and insert the operating handle into the open / close operating mechanism.2. Rotate the operating handle ACW to the stop position to charge the operating spring then CW to the stop position to close the transformer fuse switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

Caution

Caution

C 2 E 2

F 2

C 2 E 2

Prior To Any Local Operation Check / Confirm Oil Levels Gas Pressure Labeling Status Indicators

1

1

1

2

2

22

Closing

Opening Earthing Isolate / Misc

Symbols Colour / Reference Operating Instruction Colour Reference Switchgear Category Colour Reference

Overhead

Underground

LV

Circuit Breakers

MiscYesYesNo

No

CautionC 2 Main Picture

Grid ReferenceNote


Date Issued: 4 May 2010Doc Ref: WPManualInstructions1

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1DISTRIBUTION - HOW TO USE THIS MANUAL

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

DIS

TR

IBU

TIO

N - H

OW

TO

US

E T

HIS

MA

NU

AL

1 of 2

The following is a general guide for the use of this manual. For company specific instructions please refer to the introductory pages. Page 1 of this guide template shows how to interpret data on 'Page 1' of all templates in this manual. Please turn over for a guide on interpreting data on 'Pages 2, 3 and 4' of templates in this manual.

Document reference name.

Quote this for updates etc.

Company logo. Identifies

the manual issuing

company.

Switchgear name. Templates are

sorted in alphabetical order.

Switchgear details. Rating is maximum current load rating. If text is red then rating is maximum load

breaking capacity.

Operating option icons. Use these as a quick visual reference for

operating function options on this switchgear.

Page number icon. Indicates the total number

of pages used for the switchgear information.

Date issued.Indicates

issuing date for switchgear template. This must be the

same as listed in the manual

index.

Red arrows Indicate nominal

operating voltage (KV) or

LV where specifically indicated.

Switchgear photograph. May be one

shot or a montage showing

switchgear options.

Main switchgear

picture reference grid.Refer to grid

co-ordinates in top left corner of operating instruction pictures.

Special notes. General

precautions / instructions pertinent to switchgear

type.

Quick reference legend for mandatory operational

checks prior to operation

Mainphotograph grid reference. This

refers to the section of the

main photograph

shown in operating

instruction.

Operating instruction

photographs. In most cases

the photograph will show

apparatus as you would find

it prior to performing the

operation.

Switchgear operating

options. Red arrows indicate

functions available.

Operating instruction.

Step numbers correspond

with coloured arrows in the

adjacent photograph.

Special notes pertinent to the

particular operating instruction

Page number within

switchgear category colour.

Western Power

document reference number.

Switchgear name in large type for quick referencing.

Switchgear category colour for

quick referencing.

Operating instruction arrows. Numbers correspond with step numbers in adjacent operating instructions. Arrows

are colour coded for the particular operation.

Operating instruction headings. Headings are colour coded for the particular operating

instruction.


Date Issued: 2 March 2006 Doc Ref: WPAlstomFBX2

ALSTOMFBX

AL

ST

OM

FB

X

2 of 2

Operation

Opening the Transformer Fuse Switch

Special Notes


1. Unlock if required and insert the operating handle into the open / close operating mechanism.2. Rotate the operating handle ACW marginally to the stop position to open the transformer fuse switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

OperationClosing the Earth Switch

Special Notes

Confirm the earth switch location and labeling prior to operation.

Ensure the remote end of the circuit / transformer to be earthed is isolated.

1. Confirm the circuit / transformer fuse switch is open.2. Test 'Safe to Earth' with the neon indicator as shown.3. Slide the earth switch interlock lever to the right and:4. Unlock if required and insert the operating handle into the earth switch operating mechanism.5. Rotate the operating handle CW to the stop position to close the earth switch. Remove the operating handle.6. Confirm the mechanical indicator agrees with the earth switch status.

Caution

F 2

C 2 D 2 F 2

OperationOpening the Earth Switch

Special Notes


1. Unlock if required and insert the operating handle into the earth switch operating mechanism.2. Rotate the operating handle ACW to the stop position to open the earth switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the earth switch status.

Caution

C 2 D 2 F 2

OperationAccess to the HV Fuses

Special Notes


1. Confirm the transformer fuse switch is open and the transformer earth switch is closed.2. Confirm the HV fuse operation via the red mechanical indicator as shown. 3. Insert the supplied HV fuse access panel latch key and rotate ACW. Remove the key.4. Raise the HV fuse access panel interlock and lower the HV fuse access panel.

Caution

F 2 F 4

4

2

3


Special Notes

Ensure the HV fuse striker pin is located in the top mounting assembly.

Exercise caution when removing HV fuses as they may be hot.

5. Grasp the end cap tabs as shown and withdraw the required HV fuse.6. Replace the required HV fuse(s) with the striker pin(s) facing towards the access cover.7. Raise the HV fuse access panel.8. Insert the supplied HV fuse access panel latch key and rotate CW. Remove the key.

Caution

F 4

5

5

1

52

34

1

2

2

Closing

Opening Earthing Isolate / Misc

Symbols Colour / Reference Operating Instruction Colour Reference Switchgear Category Colour Reference

Overhead

Underground

LV

Circuit Breakers

MiscYesYesNo

No

CautionC 2 Main Picture

Grid ReferenceNote

Operating option icons. Use these as a quick visual reference for

operating function options on this switchgear.


Date Issued: 4 May 2010 Doc Ref: WPManualInstructions2

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

DIS

TR

IBU

TIO

N -

HO

W T

O U

SE

TH

IS M

AN

UA

LNETWORK SWITCHGEAR INSTRUCTION MANUAL 1

DISTRIBUTION - HOW TO USE THIS MANUAL

2 of 2

Page 2 of this guide template shows how to interpret data on 'Pages 2, 3 and 4' of templates in this manual. In the majority of cases a complete switchgear template will consist of two pages only. If more than two pages are required for a particular switchgear item the total page number will be indicated in the top right hand corner of 'Page 1' of the relevant switchgear template. If a switchgear item has only one page of instructions the reverse side of the template will not have a page reference and will only show the switchgear item name and operation icons. The words 'This page is deliberately left blank' will be printed in the centre of the page.

Document reference name. Quote this for for

updates etc.

Switchgear name. Templates are sorted in

alphabetical order.

Page number icon. Indicates the total number of pages used for the switchgear information. If the template has only one

page nothing will appear here.

Date issued.Indicates

issuing date for switchgear template. This must be the

same as listed in the manual

index.

Page number within

switchgear category colour. If

template has only one page

nothing will appear here.

Operating instruction.

Step numbers correspond

with coloured arrows in adjacent

photograph.

Operating instruction headings.

Headings are colour coded

for the particular operating

instruction.

Western Power document

reference number.

Switchgear name in large type for quick referencing.

Switchgear category colour for quick referencing.

Special notes pertinent to the

particular operating instruction

Operating instruction

photographs. In most cases

the photograph will show

apparatus as you would find

it prior to performing the

operation.

Main photograph

grid reference. This refers to

section of main photograph

shown in operating

instruction.


Local Manual OperatingHandle Open / Close

HV Stick - Close

Access Cover - Bolted

Relay / Meter AnalogHV Stick - Open

Arc Fault Protection

Air Operated

Relay Targets - Flag LED

Local Manual PushButton Close

Local Electrical Close

LV Links

Distance Protection

Overcurrent Protection Tap ChangerAutomatic

Isolation

Differential Protection

Lock and Tag

Open

Oil Level Gauge

Not ApplicableDo Not Operate

Remote ElectricalOpen / Close

Interlock Key

Auto Reclose

Closed

Local Manual PushButton Open / Close

Remote Electrical Open

HV Stick - Open / Close

Assembly Required Local Manual PushButton Open

Remote Electrical Close

Local Electrical Open

Earth Fault Protection

Tap ChangerManual

Pilot Wire Protection

Padlock Open

Padlock Close

Local Manual OperatingHandle Close

Racking In / Out

Fault Indicators

Local Manual OperatingHandle Open

Gas / Oil PressureGauge

Hand Operated Close

Hand OperatedClose / Open

HV fuses

Racking Trolley - CB

Local ElectricalClose / open

Earthing - ManualApplied

Test Probes

Plug Box - CB

LV De-ion / Fuse

Latching

Spring Charge

Solenoid Operated

Shutters

Directional Protection

Local Manual OperatingHandle - Earthing

Earthing Via CB / Switch

Hand Operated Open

Rackable VT

Viewing Ports

Two Man operation

HV Stick - Earthing

Relay / Meter Digital

Hydraulic Pump

LV Fuse

CW ClockwiseACW Anti-clockwise

Page 1 0f 1 Page 1 0f 2

Page 2 0f 2

Page 1 0f 3

Page 2 0f 3

Page 3 0f 3

Page 1 0f 4

Page 2 0f 4

Page 3 0f 4

Page 4 0f 4Instruction ContinuedFrom Previous PageInstruction Continued

A

A

A

A

D

H

HC

LH

R

R

T

TM

A

P

O

Manual Open / Close

Manual Close

Manual Open

L

Linked Templates Visual Confirmation Magnified Image


Date Issued: 4 May 2010Doc Ref: WPSymbolLegend1

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1SYMBOL LEGEND

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

SY

MB

OL

LE

GE

ND

1 of 1

The following information is the Symbol Legend for the Western Power Network Switchgear Instruction Manual 1 .

Please refer to the How To Use This Manual template for further details on how to use this Network Switchgear Instruction Manual 1 .

SYMBOL LEGEND


Date Issued: 4 May 2010 Doc Ref: WPSymbolLegend2

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

SY

MB

OL

LE

GE

ND

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1SYMBOL LEGEND

This page is deliberately left blank.

Switchgear Type Date Issued


Date Issued: 4 May 2010Doc Ref: WPIndexV141

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1DISTRIBUTION - VERSION 1.4

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

DIS

TR

IBU

TIO

N - V

ER

SIO

N 1.4

1 of 2

2 March 20062 March 2006

4 May 20104 May 2010


17 February 2009 2 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 20062 March 2006

27 August 200727 August 2007

2 March 20062 March 20062 March 2006

17 February 200917 February 200917 February 200917 February 2009

27 August 200717 February 2009

2 March 200627 August 200727 August 2007

2 March 200617 February 2009

27 August 20072 March 2006

17 February 200927 August 2007

17 February 200917 February 200917 February 200917 February 200917 February 2009

2 March 20062 March 20062 March 20062 March 2006

The following is an index of all switchgear templates in this manual.Please note: The Date Issued data on each switchgear template must be the same as in this index. Any additions or reissue of current switchgear templates will be accompanied with a new index template. Templates are listed alphabetically. Please ensure all templates in the manual, including new and reissued, are sorted alphabetically. Denotes new templates issued with this Index - Version 1.4

Underground Switchgear

Overhead Switchgear

Circuit Breakers

Alstom FBA5 (2 Templates) Alstom FBX Alstom Fluokit M Alstom Fluokit M C10M Motorised Isolator English Electric OLX Felten & Guilleaume GA2K GEC DDFAHazemeyer Magnefix MD (2 Templates) Holec SVS (2 Templates) Long & Crawford ETV3/2 Long & Crawford T4GF3 (2 Templates) Long & Crawford Type GF3 & J4 Long & Crawford Type J Long & Crawford Type J3 Long & Crawford Type R3 Merlin Gerin RM6 Ring Main Isolator - Type 1 Merlin Gerin RM6 Ring Main Isolator - Type 2 Merlin Gerin / Schneider SM6 (2 Templates) Merlin Gerin / Schneider SM6 Circuit Breaker Merlin Gerin Vercors M6 Nebb Brown Boveri RGB12 S & C SML 20 Fuse Element S & C SML 20 Ground Mounted Fuse (2 Templates) Schneider D14 Circuit Switch Siemens 8CK2 Western Power Mechanical Actuator

ABB NWI-58 Pole Top Capacitor ALM Air Break Switch Falcon Air Break Switch Falcon - Ezybreak Air Break Switch Haycolec Sectionaliser Type 01-04 HV Drop-out (HVDO) Fuses McGraw Edison RV ACR Nulec N24-150 Auto Circuit Recloser Nulec RL Load Break Switch / Sectionaliser Nulec U27 ACR Nulec W Series Single Phase Auto Circuit Recloser Reyrolle OYT Recloser S & C Fault Tamer (2 Templates) S & C SMD20 Boric Acid Drop-out Fuses Stanger In Line Links

ABB Unigear ZS1 Capacitor Circuit Interlock ABB Unigear ZS1 Circuit Breaker (2 Templates) ABB Unigear ZS1 Earth Switch ABB Unigear ZS1 Transformer Switch / Earth Switch / HV Fuses ABB Unigear ZS1 VT Alstom GL 107 Circuit Breaker Alstom HWX Busbar Earth Switch Alstom HWX Circuit Breaker (2 Templates) Alstom HWX VT

Switchgear Type Date Issued


Date Issued: 4 May 2010 Doc Ref: WPIndexV142

NE

TW

OR

K S

WIT

CH

GE

AR

INS

TR

UC

TIO

N M

AN

UA

L 1

DIS

TR

IBU

TIO

N -

VE

RS

ION

1.4

NETWORK SWITCHGEAR INSTRUCTION MANUAL 1DISTRIBUTION - VERSION 1.4

2 of 2

ASEA HLC 63-52/1250 Circuit BreakerEmail J18 Solenoid CBEmail J22 Solenoid CBEnglish Electric OKW3 Circuit Breaker GEC Alsthom SBV 24 Circuit Breaker (2 Templates) GEC Alsthom SBV 24 Earth Truck (2 Templates)GEC D4XD Circuit BreakerGEC OX36 Circuit BreakerInoue Denki 30TE0150RS Circuit BreakerMagrini Galileo 38 MGE 1000 BM Circuit BreakerMagrini Galileo 38 MGE 1000 BM20 Circuit BreakerMagrini Scarpa E Magnano MMS24C Circuit BreakerNilsen AEI JB422/OMI Retrofit Circuit Breaker (2 Templates) Nilsen GEC OLX Retrofit Circuit Breaker (2 Templates) Nuovo Magrini Galileo 36 GI-E 25 Type 1Nuovo Magrini Galileo 36 GI-E 25 Type 2Reyrolle 2A9T/X1/MO Circuit Breaker (2 Templates) Reyrolle D16 GFC H VT Reyrolle LMVP X5B / X8 Circuit Breaker (2 Templates) Reyrolle LMVP X5B / X8 CB Earthing Schneider AD4 MC Set Type SF1 CB (2 Templates) Schneider AD4 MC Set Type SF1 Earth Switch Schneider AD4 MC Set Type SF1 VTWestern Power CB Earth Switch - Generic (2 Templates)Westinghouse (Siemens) Retrofit J18 CBYorkshire YSF6 Circuit Breaker (2 Templates)

Alarm and Fault Relay Flags - Distribution SystemEquipment Label Reading (2 Templates)Horstmann Alpha E Fault Indicator Horstmann Fluid Type Fault Indicator HV - LV Fuse Rating Tables Kyle Form 4C Electronic Recloser Control Nulec CAPM2 Electronic Recloser Control (2 Templates) Nulec CAPM5 Electronic Recloser Control (2 Templates) Nulec Electronic Control Box Operation Flow Chart SEL 351 Protection Relay

GEC VR-1 Voltage Regulator Control

ABB SLBM / BSL 3 Phase Gang Isolator Nilsen AB5 / 200 Circuit Breaker Nilsen NAB1 / 20 Circuit Breaker


17 February 200917 February 2009

2 March 20064 May 2010


27 August 200727 August 2007


9 November 20062 March 2006

17 February 200917 February 200917 February 200917 February 200917 February 2009

2 March 20062 March 20062 March 2006

9 November 20064 May 2010

17 February 20099 November 2006

4 May 20102 March 2006

17 February 200917 February 20099 November 20069 November 2006

17 February 2009

27 August 20072 March 20062 March 2006

Miscellaneous Equipment

Voltage Regulators

Low Voltage Switchgear

Operation Options

Special Notes

Ensure the switchgear is fit for service prior to and after operation.Note: The transformer fuse switch has a different operating mechanism to the circuit switch.Note: The earth switch operating handle is different to the circuit switch operating handle.

Note: This switchgear can have both a local manual and electrical operation option. Confirm the mechanism type prior to operation. Remote electrical operation is always the preferred method of operation.

Caution


Date Issued: 2 March 2006Doc Ref: WPAlstomFBA51

OpeningClosingIsolationRackingSpring Charge

EarthingAuto RecloseHV FusesO/C ProtectionE/F Protection

3322116.6

33022013266



AlstomFBA5630 Amps16 KASF6

ALSTOMFBA5

AL

ST

OM

FB

A5

1 of 3

Voltage KV


Special Notes


Special Notes




Special Notes



Operation


Caution

Caution

Caution

D 3

F 3

D 3


1

1

1

2

2

22


Date Issued: 2 March 2006 Doc Ref: WPAlstomFBA52

ALSTOMFBA5

AL

ST

OM

FB

A5

2 of 3

Operation


Special Notes



Caution

OperationClosing / Opening the Circuit Switch - Local Elec.

Special Notes


At the completion of the electrical operation confirm the circuit switch status via the mechanical indicator.

1. Confirm the '24 VOLT DC SUPPLY FOR CONTROL' switch is on.2. Plug in the remote operation control switch as shown and stand away from the RMU.3. Rotate the switch CW to the 'ON' position to close the circuit switch.4. Rotate the switch ACW to the 'OFF' position to open the circuit switch.5. If required unplug the remote operation control switch.

Caution

F 3

B 1

OperationClosing the Remote Circuit Switch - Manually

Special Notes


At the completion of the operation confirm the circuit switch status via the mechanical indicator.

1. Switch the '24 VOLT DC SUPPLY FOR CONTROL' off.2. Unlock if required and insert the operating handle into the open / close operating mechanism as shown.3. Rotate the operating handle CW until the circuit switch closes.4. Remove the operating handle. Lock if required.5. If required switch the '24 VOLT DC SUPPLY FOR CONTROL' on.

Caution

B 2

OperationOpening the Remote Circuit Switch - Manually

Special Notes


At the completion of the operation confirm the circuit switch status via the mechanical indicator.

1. Switch the '24 VOLT DC SUPPLY FOR CONTROL' off.2. Unlock if required and insert the operating handle into the open / close operating mechanism as shown.3. Rotate the operating handle CW until the circuit switch opens.4. Remove the operating handle. Lock if required.5. If required switch the '24 VOLT DC SUPPLY FOR CONTROL' on.

Caution

B 2

1

1

2

3

3

2

2

2

34


Special Notes



1. Confirm the circuit / transformer fuse switch is open.2. Test 'Safe to Earth' with the neon indicator as shown.3. Slide the earth switch interlock lever to the left and:4. Unlock if required and insert the earth switch operating handle into the earth switch operating mechanism.5. Rotate the operating handle CW to the stop position to close the earth switch. Remove the operating handle.6. Confirm the mechanical indicator agrees with the earth switch status.

Caution

C 3 E 3 G 3

5

23

4

Date Issued: 2 March 2006Doc Ref: WPAlstomFBA53

3 of 3Document Number PSC/80/3(78)V1 Network Switchgear Instruction Manual Design Artefact Systems Pty Ltd.

ALSTOMFBA5A

LS

TO

M F

BA

5


Special Notes


1. Unlock if required and insert the earth switch operating handle into the earth switch operating mechanism.2. Rotate the operating handle ACW to the stop position to open the earth switch.3. Remove the earth switch operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the earth switch status.

Caution

C 3 E 3 G 3


Special Notes


1. Confirm the transformer fuse switch is open and the transformer earth switch is closed.2. Confirm the HV fuse operation via the red indicator as shown. 3. Insert the supplied HV fuse access panel latch key and rotate ACW. Remove the key.4. Remove the HV fuse access panel.

Caution

F 7 G 5

2

3


Special Notes



5. Grasp the end cap tabs as shown and withdraw the required HV fuse.6. Replace the required HV fuse(s) with the striker pin(s) facing towards the access panel.7. Replace the HV fuse access panel.8. Insert the supplied HV fuse access cover latch key and rotate CW. Remove the key.

Caution

F 5

4

4

12



Date Issued: 2 March 2006 Doc Ref: WPAlstomFBA54

AL

ST

OM

FB

A5

ALSTOMFBA5

Operation Options

Special Notes



Caution


Date Issued: 2 March 2006Doc Ref: WPAlstomFBX1



3322116.6

33022013266



AlstomFBX630 Amps16 KASF6

ALSTOMFBX

AL

ST

OM

FB

X

1 of 2

Voltage KV


Special Notes


Special Notes




Special Notes



Operation


Caution

Caution

Caution

C 2 E 2

F 2

C 2 E 2


1

1

1

2

2

22


Date Issued: 2 March 2006 Doc Ref: WPAlstomFBX2

ALSTOMFBX

AL

ST

OM

FB

X

2 of 2

Operation


Special Notes



Caution


Special Notes



1. Confirm the circuit / transformer fuse switch is open.2. Test 'Safe to Earth' with the neon indicator as shown.3. Slide the earth switch interlock lever to the right and:4. Unlock if required and insert the operating handle into the earth switch operating mechanism.5. Rotate the operating handle CW to the stop position to close the earth switch. Remove the operating handle.6. Confirm the mechanical indicator agrees with the earth switch status.

Caution

F 2

C 2 D 2 F 2


Special Notes


1. Unlock if required and insert the operating handle into the earth switch operating mechanism.2. Rotate the operating handle ACW to the stop position to open the earth switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the earth switch status.

Caution

C 2 D 2 F 2


Special Notes


1. Confirm the transformer fuse switch is open and the transformer earth switch is closed.2. Confirm the HV fuse operation via the red mechanical indicator as shown. 3. Insert the supplied HV fuse access panel latch key and rotate ACW. Remove the key.4. Raise the HV fuse access panel interlock and lower the HV fuse access panel.

Caution

F 2 F 4

4

2

3


Special Notes



5. Grasp the end cap tabs as shown and withdraw the required HV fuse.6. Replace the required HV fuse(s) with the striker pin(s) facing towards the access cover.7. Raise the HV fuse access panel.8. Insert the supplied HV fuse access panel latch key and rotate CW. Remove the key.

Caution

F 4

5

5

1

52

34

1

2

2

33

2

2

3

3

1

1

2

1

Operation Options

Special Notes


Note: The transformer fuse switch has a different operating mechanism to the circuit switch. The main picture shows a transformer fuse switch.

Note: There is a motorised version of this switchgear. Refer to the ALSTOM FLUOKIT M C10M MOTORISED ISOLATOR template in this manual if required.

Caution


Date Issued: 4 May 2010Doc Ref: WPAlstomFluokitM1

OpeningClosingSpring Charge

EarthingHV Fuses

33 22 11 6.6

330 220 132 66



Alstom FluokitM630 Amps630 AmpsSF6

ALSTOM FLUOKIT MA

LS

TO

M F

LU

OK

IT M

1 of 2

Voltage KV

Operation Closing the Circuit Switch

Special Notes

Confirm the circuit switch location and labeling prior to any operation.

Special Notes

1. Unlock if required and slide out the operating handle interlock bar.2. Insert the operating handle into the operating mechanism as shown.3. Rotate the operating handle ACW to the stop position to close the circuit switch.4. Remove the operating handle.5. Confirm the mechanical indicator shows

Operation Opening the Circuit Switch 1. Unlock if required and slide out the operating handle interlock bar.2. Insert the operating handle into the operating mechanism as shown.3. Rotate the operating handle CW to the stop position to open the circuit switch.4. Remove the operating handle.5. Confirm the mechanical indicator shows

Special Notes

Confirm the transformer fuse switch location and labeling prior to any operation.


Operation

Closing the Transformer Fuse Switch 1. Unlock if required and slide out the operating handle interlock bar.2. Insert the operating handle into the operating mechanism as shown.3. Rotate the operating handle ACW to the stop position to close the transformer fuse switch then rotate the handle CW to charge the tripping mechanism spring.4. Confirm the mechanical indicator shows

Caution

Caution

Caution

D 4

D 4 F 4

D 4



Date Issued: 4 May 2010 Doc Ref: WPAlstomFluokitM2

ALSTOM FLUOKIT M A

LS

TO

M F

LU

OK

IT M

2 of 2

Operation


Special Notes


1. Slide out the operating mechanism interlock bar as shown.2. Raise the trip lever to open the transformer fuse switch.3. Confirm the mechanical indicator shows

Caution

Operation Closing the HV Earth Switch

Special Notes

Confirm the HV earth switch location and labeling prior to any operation.


1. Slide out the operating mechanism interlock bar. 2. Confirm the relevant HV switch is open.3. Perform a 'Safe To Earth' test using the neon indicators.4. Insert the operating handle into the earth switch operating mechanism as shown.5. Rotate the operating handle CW to the stop position to close the earth switch.6. Confirm the mechanical indicator shows

Caution

F 2

F 4

Operation Opening the HV Earth Switch

Special Notes

Confirm the HV earth switch location and labeling prior to any operation.

1. Slide out the operating mechanism interlock bar. 2. Insert the operating handle into the earth switch operating mechanism as shown.3. Shift the earth switch interlock lever to the right (as shown) and gently rotate the operating handle ACW to the first stop position. Release the interlock lever.4. Rotate the operating handle ACW to the stop position to open the HV earth switch.5. Confirm the mechanical indicator shows

Caution

F 4

Operation Access to the HV Fuses

Special Notes

HV fuse striker pins must be located on the top of the HV fuse.

Exercise caution when handling HV fuses as they may be hot.

1. Confirm the relevant HV transformer HV earth switch is closed.2. Rotate the HV fuse access cover handle ACW and remove the access cover.

Caution

D 8

1

2

1

5

4

4

3

3

23

2

31

3

2

6

74

Operation Options

Special Notes


Note: For operation of the earth switch and access to the HV fuses refer to the ALSTOM FLUOKIT M template in this manual.

Caution


Date Issued: 4 May 2010Doc Ref: WPAlstomFluokitMC10m1

3322116.6

33022013266



Alstom FluokitM C10m Motorised Isolator630 Amps630 AmpsSF6

ALSTOM FLUOKIT MC10M MOTORISED ISOLATOR

AL

ST

OM

FL

UO

KIT

M C

10M M

OT

OR

ISE

D IS

OL

AT

OR

1 of 2

Voltage KV

OperationClosing / Opening the Circuit Switch - Local Elec.

Closing / Opening the Circuit Switch - Local Elec.


Special Notes


Special Notes

1. Rotate the 'LOCAL REMOTE' switch on the RTU ACW to the 'LOCAL' position.

Operation

2. Confirm the 'ISOLATION SWITCH' on the panel directly above the switch unit is in the 'I' (on) position as shown.3. Confirm the key locking switch on the switchgear panel is in the 'I' (on) position as shown.

Special Notes

Confirm the remote operating switch is in the neutral (vertical) position before plugging the control cable into the socket.


Operation

4. Plug the remote operating switch control cable connector into the socket on the panel directly above the switch unit as shown.5. With the operating switch in hand move a safe distance from the switch unit.To Close:6. Rotate the remote operating switch CW to the 'ON' position and release to close the switch.7. Confirm the mechanical indicator shows

Caution

Caution

Caution

N/A

G 3

F 2 E 4


Opening / Closing - RemoteOpening / Closing - Local ElectricalOpening / Closing - ManualEarth Switch Opening / Closing - Manual

83

2

910

4

4

5

76

9

1113

13

8


Date Issued: 4 May 2010 Doc Ref: WPAlstomFluokitMC10m2

ALSTOM FLUOKIT MC10M MOTORISED ISOLATOR

AL

ST

OM

FL

UO

KIT

M C

10M

MO

TO

RIS

ED

ISO

LA

TO

R

2 of 2

Operation Special Notes


1. Rotate the 'LOCAL REMOTE' switch on the RTU ACW to the 'LOCAL' position.2. Rotate the 'ISOLATION SWITCH' on the panel directly above the switch unit ACW to the 'O' (off) position.3. Rotate the key locking switch on the switchgear panel CW to the 'O' (off) position.

Caution

F 2 E 4



4. Rotate the manual control knob on the switchgear panel ACW until the notches align with the black indicators.5. Unlock and remove the padlock then slide out the operating mechanism interlock bar.

Caution

C 6



To Close: 6. Insert the operating handle into the operating mechanism as shown.7. Rotate the operating handle ACW to the stop position to close the switch.8. Confirm the mechanical indicator showsTo Open:9. Rotate the operating handle CW to the stop position to open the switch.

Caution

C 6

Closing / Opening the Circuit Switch - Manually



Special Notes


Operation

To Open:8. Rotate the remote operating switch ACW to the 'OFF' position and release to open the switch.9. Confirm the mechanical indicator shows10. At the completion of the operation remove the remote operating switch cable connector from the socket.11. Rotate the 'LOCAL REMOTE' switch on the RTU CW to the 'REMOTE' position.

Caution

G 3



10. Remove the operating handle.11. Confirm the mechanical indicator shows12. Replace the operating mechanism interlock bar and padlock.13. Rotate the manual control knob on the switchgear panel CW until the notches are clear of the black indicators.14. Rotate the key locking switch CW to the 'O' (on) position.15. Rotate the 'ISOLATION SWITCH' CW to the 'I' (on) position.16. Rotate the 'LOCAL REMOTE' switch on the RTU CW to the 'REMOTE' position.

Caution

C 6



Operation Options

Special Notes


Note: This switchgear is not spring assisted. All operations must be done in a firm and continuous motion to the stop position.

Caution


Date Issued: 2 March 2006Doc Ref: WPEnglishElectricOLX1


EarthingAuto RecloseTest ProbesO/C ProtectionE/F Protection

3322116.6

33022013266



English ElectricOLX800 Amps800 AmpsOil

ENGLISH ELECTRIC OLX

EN

GL

ISH

EL

EC

TR

IC O

LX

1 of 2

Voltage KV


Special Notes


The operation is not spring assisted. Move the operating handle in a firm and continuous motion.

Special Notes

1. Unlock if required and rotate the circuit interlock ACW.2. Withdraw the circuit interlock pin.3. Move the operating handle CW in a firm and continuous motion to the stop position to close the circuit switch. 4. Confirm the operating handle aligns with the 'ON' indicator.5. Push in the circuit interlock pin.6. Rotate the circuit interlock CW and lock if required.

OperationOpening the Circuit / Transformer Fuse Switch

1. Unlock if required and rotate the circuit interlock ACW.2. Withdraw the circuit interlock pin.3. Move the operating handle ACW in a firm and continuous motion to the stop position to open the circuit switch. 4. Confirm the operating handle aligns with the 'OFF' indicator.5. Push in the circuit interlock pin.6. Rotate the circuit interlock CW and lock if required.

Special Notes

Confirm the remote end of the circuit is isolated prior to closing the earth switch.




Operation

Closing the Circuit Earth Switch1. Confirm the relevant circuit switch is open.2. Confirm the circuit interlock is rotated CW to the stop position as shown. Lock if required.3. Unlock if required and rotate the earth interlock CW.4. Withdraw the earth interlock pin.

Caution

Caution

Caution

G 2 G 3

C 2

G 6 F 7


3

3

3

4

2

2

2

1

2

1


Date Issued: 2 March 2006 Doc Ref: WPEnglishElectricOLX2

ENGLISH ELECTRICOLX

EN

GL

ISH

EL

EC

TR

IC O

LX

2 of 2

Operation

Closing the Circuit Earth Switch

Special Notes

Confirm the remote end of the circuit is isolated prior to closing the earth switch.


5. Move the operating handle ACW in a firm and continuous motion to the stop position to close the earth switch.6. Push in the earth interlock pin.7. Rotate the earth interlock ACW and lock if required.

Caution

OperationOpening the Circuit Earth Switch

Special Notes

Confirm the circuit earth switch location and labeling prior to operation.

1. Unlock if required and rotate the earth interlock CW.2. Withdraw the earth interlock pin.3. Move the operating handle CW to the stop position to open the earth switch. 4. Confirm the operating handle aligns with the 'OFF' indicator.5. Push in the earth interlock pin.6. Rotate the circuit interlock ACW and lock if required.

Caution

C 2

C 2

E 7 OperationAccess to the Test Probes

Special Notes

Confirm the circuit earth switch location and labeling prior to operation.

1. Confirm the relevant circuit earth switch is closed.2. Unscrew the two (2) access cover retaining bolts.3. Lower the access cover.

Caution

A 7

6

2

1

7

5

3

OperationAccess to the Test Probes

Special Notes


4. Insert the appropriate probes to the stop position.5. Open the circuit earth switch. Perform tests as required.6. Close the circuit earth switch.7. Withdraw the probes.8. Close the access cover.9. Tighten the two (2) access cover retaining bolts.

Caution

A 7 E 7

2

4 4 4

1

OperationChecking the Switchgear Oil Level

Special Notes

Note: The oil level dipstick must be screwed home prior to checking oil levels.

1. Unscrew the oil level dipstick at the rear of the switchgear unit to confirm correct oil levels. At the completion of the check ensure the dipstick is screwed home correctly.

Caution

N/A

2

Operation Options

Special Notes

Ensure the switchgear is fit for service prior to and after operation. Note: The transformer fuse switch has a different operating mechanism to the circuit switch.

Caution


Date Issued: 2 March 2006Doc Ref: WPF&GGA2K1

Opening Closing Isolation Racking Spring Charge

Earthing Auto Reclose HV Fuses O/C Protection E/F Protection

33 22 11 6.6

330 220 132 66



Felten & Guilleaume GA2K 630 Amps 630 Amps SF6

FELTEN & GUILLEAUMEGA2K

FE

LTE

N &

GU

ILL

EA

UM

E G

A2K

1 of 2

Voltage KV


Special Notes


Special Notes

1. Open the circuit switch open / close operating mechanism access flap.2. Insert the operating handle into the open / close operating mechanism.3. Push in and rotate the operating handle CW to the stop position to close the circuit switch. Remove the operating handle.4. Confirm the mechanical indicator agrees with the circuit switch status.

Operation Opening the Circuit Switch 1. Open the circuit switch open / close operating mechanism access flap.2. Insert the operating handle into the open / close operating mechanism.3. Push in and rotate the operating handle ACW to the stop position to open the circuit switch. Remove the operating handle.4. Confirm the mechanical indicator agrees with the circuit switch status.

Special Notes



Operation

Closing the Transformer Fuse Switch 1. Open the transformer fuse switch open / close operating mechanism access flap.2. Insert the operating handle into the open / close operating mechanism.3. Push in and rotate the operating handle ACW to the stop position then CW to the stop position to close the transformer fuse switch. Remove the handle.4. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

Caution

Caution

C 2 D 2

F 2

C 2 D 2


2

2

2

3

3

3


Date Issued: 2 March 2006 Doc Ref: WPF&GGA2K2

FELTEN & GUILLEAUMEGA2K

FE

LTE

N &

GU

ILL

EA

UM

E G

A2K

2 of 2

Operation


Special Notes


1. Open the transformer fuse switch open / close operating mechanism access flap.2. Insert the operating handle into the open / close operating mechanism.3. Push in and rotate the operating handle ACW marginally to the stop position to open the transformer fuse switch. Remove the operating handle.4. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

Operation Closing the Earth Switch

Special Notes



1. Confirm the circuit / transformer fuse switch is open.2. Unlock if required and open the earth switch open / close operating mechanism access flap.3. Insert the operating handle into the earth switch operating mechanism.4. Push in and rotate the operating handle CW to the stop position to close the earth switch.5. Confirm the mechanical indicator agrees with the earth switch status.

Caution

F 2

B 2 D 2 F 2


Special Notes


1. Unlock if required and open the earth switch open / close operating mechanism access flap.2. Insert the operating handle into the earth switch operating mechanism.3. Push in and rotate the operating handle ACW to the stop position to open the earth switch. Remove the operating handle.4. Confirm the mechanical indicator agrees with the earth switch status.

Caution

B 2 D 2 F 2


Special Notes



1. Confirm the transformer fuse switch is open and the transformer earth switch is closed.2. Insert the supplied HV fuse access cover latch key and rotate ACW. Raise and remove the HV fuse access cover.3. Raise the retaining bale of the HV fuse(s) to be replaced.4. Withdraw the HV fuse top mounting assembly.

Caution

F 3

3

2


Special Notes



5. Remove the required HV fuse from the lower mounting assembly.6. Replace the required HV fuse(s) with the striker pin(s) pointing to the top.7. Clean and lubricate all contact fittings prior to restoration of the HV fuse mounting assemblies.8. Lower the HV fuse retaining bale.9. Replace the HV fuse access cover and latch using the supplied latch key.

Caution

F 3

5

8

2

3

3

32

4

Operation Options

Special Notes

Ensure the switchgear is fit for service prior to and after any operation.

Note: The rotation direction of the operating handle for the required function - open / close - will depend on the switch location on the switchgear unit. Confirm the required direction before operating.

Note: Placing the 'FUSE ISOLATOR' in the 'ISOLATED' position earths the HV fuses.

Caution


Date Issued: 17 February 2009Doc Ref: WPGECDDFA1

OpeningClosingSpring Charge

EarthingTest ProbesHV Fuses

3322116.6

33022013266



GECDDFA400 Amps-Oil

GECDDFA

GE

C D

DFA

1 of 2

Voltage KV

OperationClosing the Circuit / Transformer Fuse Switch

Special Notes

Confirm the circuit / transformer fuse switch location and labeling prior to any operation.

Special Notes

1. Confirm the rotating interlock selector is in the circuit switch position as shown.2. Insert the operating handle into the open / close operating mechanism as shown.3. Rotate the operating handle in the required direction to the stop position to close the circuit / transformer fuse switch.4. Remove the operating handle.5. Confirm the mechanical indicator points to 'ON'.

OperationOpening the Circuit Switch1. Confirm the rotating interlock selector is in the circuit switch position as shown.2. Insert the operating handle into the open / close operating mechanism as shown.3. Rotate the operating handle in the required direction to the stop position to open the circuit switch.4. Remove the operating handle.5. Confirm the mechanical indicator points to 'OFF'.

Special Notes



Operation

Opening the Transformer Fuse Switch1. Push the 'TRIP' lever to the left to open the transformer fuse switch.2. Confirm the mechanical indicator points to 'OFF'.

Caution

Caution

Caution

B 2 F 2 G 2

D 2

F 2 G 2


1

2

1

3

3

1

2


Date Issued: 17 February 2009 Doc Ref: WPGECDDFA2

GECDDFA

GE

C D

DFA

2 of 2

Operation

Closing the Earth Switch

Special Notes


Confirm the mechanical indicator points to 'EARTH' at the completion of the operation.

1. Confirm the relevant circuit / transformer fuse switch is open.2. Unlock if required and rotate the interlock selector to the earth position as shown.3. Insert the operating handle into the open / close operating mechanism as shown.4. Rotate the operating handle in the required direction to the stop position to close the earth switch.5. Remove the operating handle.

Caution

Operation

Closing the Earth SwitchSpecial Notes

Confirm the circuit earth switch location and labeling prior to any operation.

6. Confirm the mechanical indicator points to 'EARTH'7. If required rotate the interlock and lock in the 'Earth Switch On' position as shown.

Caution

B 2 F 2 G 2

B 2 F 2 G 2


Special Notes


When replacing the HV fuse ensure the striker pin points upwards.

1. Confirm the transformer fuse switch is open.2. Confirm the HV fuse operation via the red target indicator as shown. 3. Insert the operating handle into the Fuse Isolator mechanism as shown and rotate CW to the 'ISOLATED' position. The HV fuses are now earthed.4. Raise the HV fuse access panel. Remove and replace the relevant HV fuse. Close the access panel.5. Rotate the Fuse Isolator to the 'SERVICE' position.

Caution

D 25

33

OperationAccess to the Circuit Test Probes

Special Notes

When restoring the after test ensure the earthing bar is pushed home firmly to the stop position.

1. Confirm the relevant circuit / transformer fuse switch is open and the circuit / transformer earth switch is closed.2. Unscrew the circuit test probes access cover retaining bolt.3. Lower the test probe access cover.4. Lower the earthing bar. Perform the required tests.Note: To restore, reverse the above instructions.

Caution

B 6

2

34

2

7

3

4

Operation

Opening the Earth SwitchSpecial Notes

Confirm the circuit earth switch location and labeling prior to any operation.

Confirm the mechanical indicator points to 'OFF' at the completion of the operation.

1. Unlock if required and rotate the interlock selector to the earth position as shown.2. Insert the operating handle into the open / close operating mechanism as shown.3. Rotate the operating handle in the required direction to the stop position to open the earth switch.4. Remove the operating handle.5. If required rotate the interlock selector to the circuit switch position. Lock if required.

Caution

B 2 F 2 G 2

2

31

3

Operation Options

Special Notes


Note: The three (3) phase operating handle is to be used for the closing function only.

Caution


Date Issued: 2 March 2006Doc Ref: WPHazemeyerMD1



3322116.6

33022013266



HazemeyerMagnefix MD250 / 400 Amps400 AmpsAir

HAZEMEYERMAGNEFIX MD

HA

ZE

ME

YE

R M

AG

NE

FIX

MD

1 of 3

Voltage KV

OperationClosing the Single Phase Circuit Switch Link

Special Notes

Confirm the circuit switch link location and labeling prior to operation.

Special Notes

1. Attach the switch link operating handle onto the switch link as shown.

OperationClosing the Single Phase Circuit Switch Link

2. Insert the switch link carefully in the desired position.3. Push the switch link with a firm and continuous motion to the stop position to close the link.4. Slide up the operating handle and remove from the switch link.5. Repeat this operation for all three (3) phases.

Special Notes


Ensure all three (3) phases are opened and removed correctly.


Ensure all three (3) phases are closed correctly.

Operation

Opening the Single Phase Circuit Switch Link1. Attach the switch link operating handle to the required switch link as shown.2. Grasp the operating handle and withdraw the switch link in a firm and continuous motion.3. Remove the switch link from the operating handle and stow correctly.4. Repeat this operation for all three (3) phases.5. If required place switch link spout covers onto the switch link spouts as shown.

Caution

Caution

Caution

N/A

C 2

C 2


1

32

4

1

5

2


Date Issued: 2 March 2006 Doc Ref: WPHazemeyerMD2


HA

ZE

ME

YE

R M

AG

NE

FIX

MD

2 of 3

Operation

Closing the Three Phase Circuit Switch Link

Special Notes

Confirm the circuit three phase switch link location and labeling prior to operation.

Engage the switch link three phase operating handle by:

1. Place the operating handle in a vertical position on the ground as shown. Secure in this position by placing the foot through the handle.2. Using both hands, raise the attachment cylinder until a 'click' is heard thereby latching the cylinder mechanism.

Caution

Operation

Closing the Three Phase Circuit Switch LinkSpecial Notes


3. Insert the three phase switch carefully into position ready to be closed.4. Attach the operating handle to the three phase switch link with the long tongue on the LH side as shown.5. Unlock the cylinder closing mechanism by depressing the latches as shown.6. Push in the operating handle in a firm and continuous motion to the stop position to close the three phase switch link. Remove the operating handle.

Caution

N/A

B 4

OperationOpening the Three Phase Circuit Switch Link

Special Notes


1. Grasp the three phase switch link by the two handles as shown.2. Withdraw the three phase switch link in a firm and continuous motion and stow correctly.3. If required place switch link spout covers onto the switch link spouts.

Caution

B 4

1

4

65

5

1

1

2

2

OperationEarthing the Circuit

Special Notes

Confirm the circuit location and labeling prior to operation.

Confirm the earthing lead is firmly attached to the earthing link.

1. Attach the earthing handle to the earthing link as shown.

Caution

N/A

1

OperationEarthing the Circuit

Special Notes

Confirm the circuit / earth switch location and labeling prior to operation.


2. Place the earthing link carefully on the relevant circuit spout.3. Grasp the earthing handle above the red limit ring and push the earthing link in to the stop position in a firm and continuous motion to earth the circuit.4. Remove the earthing handle.5. Repeat this operation for all three (3) phases.Note: To remove the circuit earth reverse the above instructions.

Caution

F 2

2

3

Date Issued: 2 March 2006Doc Ref: WPHazemeyerMD3


HAZEMEYERMAGNEFIX MDH

AZ

EM

EY

ER

MA

GN

EF

IX M

D

Operation

Access to the HV Fuses

Special Notes

Confirm the transformer fuse circuit location and labeling prior to operation.

1. Confirm the transformer fuse circuit switch links have been removed.2. If required, confirm the transformer fuse circuit is earthed via the earthing links.3. Rotate the HV fuse interlock ACW as shown.

Caution

G 2


Special Notes


4. Grasp the required HV fuse extraction handle and withdraw the HV fuse.5. Remove the HV fuse from the end cap and replace with a new HV fuse.

Caution

G 24

5

31

1

1


Special Notes

Note: The circuit switch links cannot be replaced unless the HV fuse interlock is in the correct position - rotated CW.

6. Insert the HV fuse into the HV fuse chamber ensuring the end cap seats home correctly.7. Rotate the HV fuse interlock CW to the stop position.

Caution

A 2

6



Date Issued: 2 March 2006 Doc Ref: WPHazemeyerMD4

HA

ZE

ME

YE

R M

AG

NE

FIX

MD


Operation Options

Special Notes



Caution


Date Issued: 2 March 2006Doc Ref: WPHolecSVS1



3322116.6

33022013266



HolecSVS630 Amps630 AmpsSF6

HOLECSVS

HO

LE

C S

VS

1 of 3

Voltage KV


Special Notes


Special Notes





Caution

Caution

F 2

F 2


1

1

2

2

Operation

Closing the Transformer Fuse Switch

Special Notes


1. Unlock if required and insert the operating handle into the transformer fuse switch open / close operating mechanism.2. Rotate the operating handle ACW to the stop position to charge the operating spring then CW to the stop position to close the transformer fuse switch.3. Remove the operating handle. Lock if required.4. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

A 2

1

2

2


Date Issued: 2 March 2006 Doc Ref: WPHolecSVS2

HOLECSVS

HO

LE

C S

VS

2 of 3

OperationOpening the Transformer Fuse Switch

Special Notes


1. Press the red 'O' button to open the transformer fuse switch.2. Confirm the mechanical indicator agrees with the transformer fuse switch status.

Caution

A 2


Special Notes

Confirm the earth selector switch location and labeling prior to operation.


1. Confirm the circuit / transformer fuse switch is open.2. Confirm 'Safe to Earth' with the LED indicators if fitted.3. Unlock if required and slide the earth switch interlock lever to the right and:4. Unlock if required and insert the operating handle into the earth switch selector mechanism.5. Rotate the operating handle CW to the stop position to select the earthing option.6. Confirm the mechanical indicator shows earthed.

Caution

F 2


Special Notes



7. Remove the operating handle from the earth switch selector mechanism and insert into the circuit switch open / close mechanism as shown.8. Rotate the operating handle CW to the stop position to close the circuit switch thereby earthing the circuit.9. Confirm the mechanical indicator agrees with the circuit / earth switch status.

Caution

F 2

1

5

8

3

4

7

2


Special Notes


1. Unlock if required and insert the operating handle into the circuit / earth switch open / close operating mechanism.2. Rotate the operating handle ACW to the stop position to open the circuit switch thereby de-earthing the circuit.3. Remove the operating handle.

Caution

F 2

2

1


Special Notes


4. Unlock if required and slide the earth switch interlock lever to the right and:5. Unlock if required and insert the operating handle into the earth switch selector mechanism.6. Rotate the operating handle ACW to the stop position to de-select the earthing option.7. Confirm the mechanical indicator shows normal circuit.8. Remove the operating handle and lock if required.

Caution

F 2

5

6

Date Issued: 2 March 2006Doc Ref: WPHolecSVS3


HOLECSVSH

OL

EC

SV

S


Special Notes



1. Confirm the transformer fuse switch is closed with the selector switch in the earth position.2. Slide the earth switch interlock across to the right and up.3. Insert the supplied HV fuse access panel latch key and rotate ACW.4. Remove the HV fuse access panel.5. Replace HV fuses as required.

Caution

A 2

2

3



Date Issued: 2 March 2006 Doc Ref: WPHolecSVS4

HO

LE

C S

VS

HOLECSVS

Operation Options

Special Notes

Ensure the circuit switch is fit for service prior to and after operation.

Note: This switchgear does not have an earthing switch.

Caution


Date Issued: 2 March 2006Doc Ref: WPLong&CrawfordETV3-21

OpeningClosingIsolationRackingLatching


3322116.6

33022013266



Long & CrawfordETV3/2200 Amps250 MVAOil

LONG & CRAWFORDETV3/2 L

ON

G &

CR

AW

FO

RD

ET

V3/2

1 of 1

Voltage KV

OperationClosing the Circuit / Transformer Fuse Switch

Special Notes

Confirm the circuit / transformer fuse switch location and labeling prior to operation.

Special Notes


1. Unlock if required and raise the operating handle to the stop position to close the switch. Lock if required.2. Confirm the mechanical indicator agrees with the switch status.

OperationOpening the Circuit / Transformer Fuse Switch

1. Unlock if required and lower the operating handle to the stop position to open the switch. Lock if required.2. Confirm the mechanical indicator agrees with the switch status.

Special Notes


Ensure the remote end of the fused circuit is isolated prior to accessing the HV fuses.

Operation

Access to the HV Fuses1. Confirm the relevant transformer fuse switch is open.2. Unlock the HV fuse access lid interlock bar and remove.3. Unscrew the two (2) HV fuse access lid retaining wing nuts and lower the retaining bolts.4. Raise the HV fuse access lid to the stop position.

Caution

Caution

Caution

F 3

C 2

F 3

1

1

1

2

33

1

Prior To Any Local Operation Check / Confirm Oil Levels Gas Pressure Labeling Correct Latching

This Page Is Deliberately Left Blank


Date Issued: 2 March 2006 Doc Ref: WPLong&CrawfordETV3-22

LONG & CRAWFORDETV3/2

LO

NG

& C

RA

WF

OR

D E

TV

3/2

Operation Options

Special Notes

Ensure the ring main isolator is fit for service prior to and after operation.

Note: The transformer fuse switch and earth switch have different operating mechanisms to the circuit switches.

Note: In some cases this switchgear may be fitted with a Western Power Mechanical A ctuator. Refer to the 'WESTERN POWER MECHANICAL ACTUATOR' template in this manual for further details if required.

Caution


Date Issued: 2 March 2006Doc Ref: WPLong&CrawfordT4GF31

Opening Closing Isolation Racking Spring Charge

Earthing Auto Reclose HV Fuses O/C Protection E/F Protection

33 22 11 6.6

330 220 132 66



Long & Crawford T4GF3 Ring Main Isolator 630 Amps 630 Amps Oil

LONG & CRAWFORDT4GF3 RING MAIN ISOLATOR

LO

NG

& C

RA

WF

OR

D T

4GF

3 RIN

G M

AIN

ISO

LA

TO

R

1 of 3

Voltage KV

Operation Configuring the Ring Main Isolator Operating Handle

Special Notes

The operating handle will 'spin free' if the ratchet cam is not set to the correct position.

Special Notes

1. Determine the required direction of the operating handle rotation - clockwise or anticlockwise. 2. Rotate the operating handle ratchet cam to the required position ,A or B, (as shown). The operating handle will only function in the direction of the ratchet cam.


1. Attach the operating handle to the circuit switch operating mechanism as shown. 2. Rotate the operating handle in the direction of the indicating arrow (adjacent to the operating mechanism) to the stop position to close the switch. 3. Confirm the mechanical indicator agrees with the switch status.

Special Notes

Confirm the circuit switch location and labeling prior to operation. Ensure the operating handle ratchet cam is set to the correct position prior to operating.

Confirm the circuit switch location and labeling prior to operation. Ensure the operating handle ratchet cam is set to the correct position prior to operating.

Operation

Opening the Circuit Switch 1. Attach the operatin

Switchgear Instruction Manual 1 Version 1 4 (2)

Documents

Transcript of Switchgear Instruction Manual 1 Version 1 4 (2)