SURFACE CLIP MOUNT - Kelvix...1 2 Insert channel into opening with spring clips compressed and then...
Transcript of SURFACE CLIP MOUNT - Kelvix...1 2 Insert channel into opening with spring clips compressed and then...
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Snap channel into mounting clips Screw mounting clips into mounting surface
43
Attach lens cover and end caps 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
SURFACE CLIP MOUNT
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Snap channel into pivot clips and adjust to desired angle
Screw pivot clips into mounting surface 43
Attach lens cover and end caps 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
SURFACE ADJUSTABLE MOUNT
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Apply channel to construction adhesive andallow to cure
Prepare mounting surface and applyconstruction adhesive
43
Attach lens cover and end caps 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
SURFACE ADHESIVE MOUNT
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Screw channel through pre-drilled holesdirectly into mounting surface
Drill mounting holes through channel 43
Attach lens cover and end caps 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
SURFACE SCREW MOUNT
Insert lens into channel, measure, and cutto length
Create recessed opening in mountingsurface
1 2
Install LED strip into channel5
Attach end caps, apply channel to construction adhesive, and allow to cure
Prepare mounting surface and then applyconstruction adhesive
43
Attach lens cover6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
RECESSED ADHESIVE MOUNT
Insert lens into channel, measure, and cutto length
Create recessed opening in mountingsurface
1 2
Install LED strip into channel5
Attach end caps and screw channel throughpre-drilled holes directly into recessedmounting surface
Remove lens cover from channel and drillmounting holes through channel
43
Attach lens cover 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
RECESSED SCREW MOUNT
Insert lens into channel, measure, and cutto length
Create recessed opening in mountingsurface
1 2
Insert channel into opening with spring clips compressed and then allow clips to release and clasp surface
5
Attach end caps and install LED strip intochannel
Remove lens cover, feed spring clips through back of channel, and tighten set screws
43
Attach lens cover 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
RECESSED SPRING CLIP MOUNT
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Snap channel into mounting clipsScrew mounting clips into mounting surface
43
Attach lens cover and end caps 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
SURFACE ANGLED CLIP MOUNT
Insert lens into channel, measure, and cutto length
Create recessed opening in mountingsurface
1 2
Apply channel to adhesive and allow to cure
5
Prepare mounting surface and then applyappropriate adhesive
Attach end caps and install LED strip intochannel
43
Attach lens cover with silicone adhesive 6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS
RECESSED INGRADE MOUNT
Remove lens cover from channelInsert lens into channel, measure, and cut to length
1 2
Install LED strip into channel5
Attach end capsUnscrew t-screws from channel couplersand feed through slot on back of channel
43
Measure ceiling and channel to determinesuspension points
6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS (Pg. 1 of 2)
CABLE SUSPENDED MOUNT
Remove t-screws from ceiling couplers andmount to ceiling with appropriate hardware
Thread channel couplers back onto t-screws at desired suspension points
7 8
Attach lens cover11
Adjust height of channel by compressing endof channel coupler and adjusting cable length
Thread t-screws back into ceiling couplersto suspend channel
109
If desired, clip excess suspension cablewith wire cutters
12
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS (Pg. 2 of 2)
CABLE SUSPENDED MOUNT (con’t)
1 2
43
Insert lens into channel, measure, and cutto length
Create recessed opening in mountingsurface
1 2
Attach end caps and screw channel through pre-drilled holes directly into recessed mounting surface
Remove lens cover from channel 43
6Attach lens cover5 Tape and mud over mounting surface, bring mud flush to edge of lens cover
6
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS (Pg. 1 of 2)
RECESSED FLUSH MOUNT
Install LED strip into channel10
11 12
8Sand mudded surface to remove any raised points from previous step
7
Attach 2nd (new) lens cover11
10Remove and discard lens cover and wipe down LED strip to remove dust
9
Turn on light and enjoy! 12
9Paint surface (optional)8
Questions/Support | 800-789-3810 | [email protected] 011918NH
CHANNEL INSTALLATION INSTRUCTIONS (Pg. 2 of 2)
RECESSED FLUSH MOUNT (con’t)