Supplier of concrete accessories and specialist products A5 Mini Brochure.pdf · Supplier of...

Supplier of concrete accessoriesand specialist products

T Wolverhampton 01902 353161 | T London 0208 345 5850

Mini catalogue

2 CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESW

ELC

OM

ECONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIES

Welcome to MCSSUPPLIER OF CONCRETE ACCESSORIES & SPECIALIST PRODUCTS

MCS are a specialist supplier of concrete accessories servicing the construction industry. The company has been trading for over ten years, during which time MCS has built an enviable reputation for providing quality products and excellent customer service. Our ability to offer customers prompt material and technical solutions has enabled us to secure preferred supply agreements with a number of leading national contractors.

This mini catalogue covers just a selection of the products available from MCS. For further details on all MCS products and services, please contact:

T Wolverhampton: 01902 353161T London: 0208 345 5850 E [email protected]

Local availability for all your concrete construction

essentials.

CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIES 3

T Wolverhampton 01902 353161 | T London 0208 345 5850

CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESIN

DE

X

ACCESSORIES 4

DOWEL BAR 7

FORMWORK 8

REINFORCING MESH 10

WALL TIES 11

CHANNELS, BOLTS & WINDPOSTS 12

SHEAR CONNECTORS & STUDS 13

CONSTRUCTION CHEMICALS 14

WATERPROOFING & GAS MEMBRANE 19

CONCRETECONSTRUCTIONACCESSORIES

4

Supplier of concrete accessories and specialist products

CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIES


CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESA

CC

ES

SO

RIE

S

DOUBLE COvER CONCRETE SPACER BLOCKSCode Cover (mm) Pack size

CB30/40 30/40 250

CB40/50 40/50 200

Flat Based Double Cover Concrete Spacer Blocks provide a solid support in heavy duty horizontal applications. PLEASE NOTE: Other sizes are available on request.

GRADE PLATE SPACERSCode Cover (mm) Pack size

GP40/50 40/50 200

Grade Plate Spacers’ large base area is ideal for use on membranes or soft ground and bar diameters of up to 20mm can be accommodated.PLEASE NOTE: Other sizes are available on request.

CONCRETE SqUARE BARCode Cover (mm) Pack length (m) Pallet quantity

CB30 30 1 600

CB40 40 1 300

CB50 50 1 250

CB75 75 1 100

Heavy Duty Concrete Bars enable fast placement of heavy reinforcement. Ideal for use on plastic membranes, sand etc. Can be used to accurately separate shutters in walls and beams.

BLACK ANNEALED TyING WIRECode Gauge Weight (kg)

TY/16 16 15

Black Annealed, Stainless Steel and Galvanised Wire is available invarious gauges and roll sizes.

REBAR SAFETy CAPS

Code Ø (mm) Pack size

RSC8/16 8-16 250

RSC16/32 16-32 250

Safety Caps to fit over the end of reinforcement bar to prevent injury.



Supplier of concrete accessories and specialist products T Wolverhampton 01902 353161 | T London 0208 345 5850


CC

ES

SO

RIE

S

DECK CHAIRS (2M LENGTHS)Code Height (mm) Lengths per pack

HC50/2 50 25

HC75/2 75 25

HC90/2 90 25

HC105/2 105 25

HC120/2 120 25

Manufactured from hard drawn wire, Continuous Wire Chairs are ideal for spacing top and bottom layers of mesh and can also be used as dowel bar supports.PLEASE NOTE: Other sizes are available on request.

2 METRE PLASTIC TRACK SPACERSCode Cover (mm) Pack size (m)

PTS20 20 100

PTS30 30 100

PTS40/60 40 60

PTS50/60 50 60

Continuous Plastic Track is ideal for supporting bottom reinforcement in suspended slabs, sloped or curved structures.

EXPANSION JOINT STRIPCode Size (mm) Code Size (mm) Code Size (mm)

CF10/100 10 x 100 CF20/150 20 x 150 CF25/150 25 x 150

CF10/125 10 x 125 CF20/175 20 x 175 CF25/175 25 x 175

CF10/150 10 x 150 CF20/200 20 x 200 CF25/200 25 x 200

CF10/175 10 x 175 CF20/225 20 x 225 CF25/225 25 x 225

CF10/200 10 x 200 CF20/250 20 x 250 CF25/250 25 x 250

Full sheets and other sizes available ex-stock.Available in standard 35kg/m3 and heavy duty 60kg/m3.

POLyTHENE DPMCode Gauge Roll size (m)

DPM500BBA 500 4 x 50

DPM1000BBA 1000 4 x 25

DPM1200BBA 1200 4 x 25

DPM2000BBA 2000 4 x 12.5

Polythene damp proof membrane manufactured to BBA standards 97/3393.

6





CC

ES

SO

RIE

S

WING NUTS


WN15 15 50

Used in conjunction with Tie Rod and Waler Plates.

WALER PLATES


WP15 15 20

For use with Tie Rod and Wing Nuts.

TIE ROD CONES


SC22 22 500

Used at the ends of Tie Rod Sleeves and can easily be removed after formwork is struck to form a chamfered recess for subsequent grouting.

TIE ROD SLEEvE

Code Int. Ø (mm) lm per pack

TB22 22 100

A rigid PVC tube used as an expendable sleeve over Tie Rods. Facilitates easy removal of Tie Rods and acts as a spacer to ensure correct width of wall. Supplied in 2m lengths.

TIE ROD BARCode Ø (mm) Length (mm)

TR15/1500 15 1500

TR15/3000 15 3000

TR15/6000 15 6000

Tie Rod is produced from high yield bar with deformations to produce a thread along the entire length of the bar. Can also be supplied pre-cut to site requirements.




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESD

OW

EL B

AR

DOWEL BARSCode Length (mm) Dia. (mm)

DB12/900 900 12

DB12/1200 1200 12

DB16/900 900 16

DB20/600 600 20

DB20/900 900 20

DB25/600 600 25

High yield or mild steel round bars, supplied with either cropped or sawn ends. Any size of bar available on request. Stainless steel dowels also available in grade 304 and 306.

DOWEL BAR SLEEvESCode Length (mm) Dia. (mm) No. per pack

DBS12/450 450 12 100

DBS16/200 200 16 100

DBS16/300 300 16 100

DBS20/300 300 20 100

DBS25/300 300 25 100

DBS32/375 375 32 100

Made from flexible PVC and used as a quick method of debonding dowel bars.

DOWEL BAR EXPANSION CAPSCode Length (mm) Dia. (mm) No. per pack

DC12 100 12 100

DC16 100 16 100

DC20 100 20 100

DC25 100 25 100

DC32 100 32 100

Made from flexible PVC and used as a quick method of debonding dowel bars.

8




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESFO

RM

WO

RK

Hy-RIB®

Sheet thickness (mm) Sheet size (mm)

0.75 445 x 2000

0.575 445 x 2000

0.575 445 x 3000

0.4 445 x 2000

0.4 445 x 3000

0.4 445 x 4000

BEAMFORM

Beamform, being rigid and having good strength to weight ratio has established itself as an ideal alternative to traditional formwork shuttering.

• Supplied in full sheets (4m x 2.4m)• Cut to size• Supply us with your drawings and we can do a full Beamform take off.

See pages 4 and 5 for spacers.

Expamet Hy-Rib® is an expanded metal sheet product, specifically developed for use as permanent formwork to concrete. The profile of the open mesh, in combination with the Hy-Rib® tangs, allows the development of dense concrete nodules and indents on the face of the Hy-Rib®, forming an enhanced mechanical key for the second phase pour.




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESFO

RM

WO

RK

K-FORM - CONCRETE SHUTTERING MADE EASy

K-FORM UPVC Screed Railing provides the construction industry with an economical, efficient and environmentally friendly alternative to steel shuttering.

Made from recycled materials, K-FORM is lightweight, durable and does not require removal after concrete pouring. It is easily cut to length on site and has pre-drilled holes in the vertical face for locating steel dowel bars and in the base for mortar anchoring. Furthermore, K-FORM’s patented design features a built in expansion joint, end clips for joining and a removable top strip for joint sealing.

ECO-SLAB™ - INSULATED CONCRETE FORMWORK

Eco-Slab™ is a unique, patented insulated concrete formwork (ICF), which offers a modern method of construction for creating ground floor slabs suitable for dwellings and non-dwellings.

It offers a simple 2 step process for casting a ground slab with an exceptionally low carbon footprint:• Embodied Carbon: 3.4kg/m2

• Operational Carbon: Used in conjunction with other technologies, Eco-Slab™ can assist in achieving Zero Carbon

Eco-Slab™ is manufactured from carbon enriched expanded polystyrene (EPS). It is a modular system consisting of 1m2 interlocking rafts and a thickened edge beam.The lap and ledge system gives enhanced U-values (is capable of achieving values of 0.13) and provides a stable working base on which to lay the slab. The thickened beam edge of 200mm ensures zero lateral thermal leakage.

10




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESR

EIN

FOR

CIN

G M

ES

H

REINFORCING MESH

BS refMesh size

Nominal pitch of wires

Wire sizesCross sectional area

per metre

Nom. weight per

m2 (kg)

Sheets per tonne

(approx.)

Sheet weight (kg)

Sheets per bundle

Sq. mtr per tonne

Main (mm)

Cross (mm)

Main(mm)

Cross (mm)

Main(mm)

Cross (mm)

A393 200 200 10 10 393 393 6.16 15 70.96 18 162.13

A252 200 200 8 8 252 252 3.95 22 45.5 28 253.16

A193 200 200 7 7 193 193 3.02 29 34.79 34 331.13

A142 200 200 6 6 142 142 2.22 40 25.57 46 450.45

B1131 100 200 12 8 1131 252 10.9 8 125.57 10 91.74

B785 100 200 10 8 785 252 8.14 11 93.57 14 122.85

B503 100 200 8 8 503 252 5.93 15 68.31 18 168.163

B385 100 200 7 7 385 193 4.53 20 52.19 24 220.75

B283 100 200 6 7 283 193 3.73 24 42.97 30 268.1

B196 100 200 5 7 196 193 3.05 29 35.14 36 327.87

Electronically cross welded mesh manufactured to meet BS 4483 from cold-reduced wire complying to BS 4482. Standard sheets to 4.8m x 2.4m. We also supply cut and bent reinforcement, simply give us your schedules or drawings and we will provide a full quotation.

EAzISTRIP REINFORCEMENT CONTINUITy SySTEM

The Eazistrip Reinforcement Continuity System is a quick and easy to install method of maintaining continuity of reinforcement at construction joints in concrete. It consists of a galvanised steel casing with a dimpled surface to provide an effective concrete bond.

Pre-bent bars are housed within the casing and are enclosed by a protective cover. Each end of the unit is sealed with apolystyrene block in order to prevent the ingress of concrete.The complete unit is nailed to the formwork. Alternatively it can be wired back to the main reinforcement cage. The concrete is then cast.

After striking the formwork, the cover is removed and the bars are straightened, ready for lapping onto the main reinforcement, using an Eazistrip re-bending tool. The steel casing remains embedded in the wall and is filled with concrete when the next section is poured, the dimpled surfaceproviding an efficient key.




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESW

ALL T

IES

ST1Code Length (mm) No. per pack

ST1200 200 100

ST1225 225 100

ST1250 250 100

ST1300 300 100

Conforms to Type 1 DD140. UK Patent No’s 2255 358, 2260 348, 2260 349.

SD1

Code Length (mm) No. per pack

SD1150 150 100

SD1200 200 100

SD1225 225 100

SD1250 250 100

SD1275 275 100

SD1300 300 100

Type 1 tie to DD140. Drip 90mm from one end as standard. Also available with central drip.

RT2


RT2200 200 250

RT2225 225 250

Type 2 tie to DD140. Patent No’s - GB2359831.

SPB


SPB75 75 100

SPB100 100 100

SPB125 125 100

SPB150 150 100

SPB175 175 100

SPB200 200 100

SPB225 225 100

SPB250 250 100

12




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESC

HA

NN

ELS

, B

OLT

S &

WIN

DP

OS

TS

CHANNELS & BOLTS

Channels Ancon Channels are produced in a range of profiles.

Fixing to channels Fixing to channels is by ‘T’ head bolts.These are inserted into the channel and turned through 90°.

Cast-in channels and sockets These sockets offer a simple solution to fixing into concrete for locations where adjustment is either unnecessary or can be provided elsewhere.

Surface fixed channels Ancon Channels can be supplied without the anchor lugs for surface fixing to concrete, steelwork and other materials.

Fixing boltsA range of fixing bolts are also available including expansion bolts, high performance bolts, set screws and drill set screws.

WINDPOSTS

Large panels of masonry or panels with openings can often be difficult to justify structurally. The traditional solutions have been to either increase the thickness of the wall or introduce an additional column. Ancon Windposts fit within the wall allowing the existing thickness to be maintained.

Ancon WP1 and WP3 Windposts Ancon WP1 and WP3 Windposts are channel section windposts which are designed to be installed within the cavity, leaving the blockwork undisturbed. The windposts are complete with end connections and ties which fit into the vertical slots in the flanges of the channel section.

Ancon WP2 Windposts Ancon WP2 Windposts are angle section windposts designed for either small cavities or where wind loads are high. One leg of the angle windpost is built into the blockwork, and the blockwork tied through the leg of thewindpost to minimise any possible movement or cracking of internal finishes. If a vertical movement joint is required in place of a tied joint, ties with a plain end on one side can be supplied.

Ancon WP4 Windposts Ancon WP4 Windposts are generally used in internal blockwork walls that have a ‘fair faced’ finish to both sides and where the windposts cannot protrude beyond either face. Sometimes referred to as ‘spine’ posts theyare flat plates designed to fit within the wall. Although the depth of a WP4 post is limited by the width of the masonry (ideally 20mm less than the wall width), the thickness of the post can vary to increase its load capacity.




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESS

HE

AR

CO

NN

EC

TO

RS

& S

TU

DS

DSD SHEAR LOAD CONNECTORS

The DSD range of connectors offers significant advantages over plain dowels. Each connector is a two-part assembly comprising a sleeveand a dowel component. Installation is a fast and accurate process, drilling of either formwork or concrete is not required. The sleeve is simply nailed to the formwork ensuring subsequent alignment with the dowel, essential for effective movement.

Ancon DSD The Ancon DSD is the original two-part, double dowel, shear load connector. The two dowels are Duplex stainless steel bar. The dowelcomponent can move longitudinally within the sleeve to accommodate movement. The connector is available in ten standard sizes and has design capacities from around 20kN to over 950kN. The larger connectors can beused in joints up to 60mm wide. Larger joints can be accommodated using special dowels.

SHEARFIX - PUNCHING SHEAR REINFORCEMENT

Used within a slab to provide additional reinforcement around columns, Ancon Shearfix is the ideal solution to the design and construction problems associated with punching shear. The system consists of double-headed studs welded to flat rails, positioned around the column head or base. The shear load from the slab is transferred through the studs into the column. Shearfix is suitable for all column shapes and is easy to install either ‘top down’ or ‘bottom up’, depending on user preference.

The Ancon Shearfix system is manufactured to suit the specific requirements of each application. The quantity of each component, the dimensions and spacings, and the layout pattern around the column are determined by calculation. Studs are manufactured in six diameters (10,12, 14, 16, 20 and 24mm) from high strength steel bar. The heads are hot forged to three times the diameter of the bar. Studs are manufactured in virtually any length to suit the depth of slab, but are normally formed in increments of 10mm within the 100-500mm range. The bar used in this system has a characteristic yield strength of 500N/mm2. The studs are welded to the rail at the determined centres. The rail performs no structural function but ensures stud alignment and positioning within the slab. Shearfix rails are manufactured from strips of steel, 16mm wide. The gap between the strips allows for concrete during pouring and also enables the rail to be nailed through spacers to formwork when fixed ‘bottom up’, i.e., prior to all other reinforcement.

14





ON

ST

RU

CT

ION

CH

EM

ICA

LS

MOULD OIL

Code Coverage Pack size

- 30m2 per litre on smooth surfaces

25 litres

- 210 litres

A general purpose, non-staining, water based mould oil that can be used on timber, steel and GRP to assist in striking and easier cleaning of formwork, giving a better finish to concrete.

CURING AID


-5-6m2 per litre

20 litres

- 210 litres

This is a non-staining solution that when applied to fresh concrete/renders/screeds, reacts with the free lime and creates minute crystals which seal the pores in concrete, preventing premature moisture loss, which reduces cracking shrinkage and surface dusting.

CONCRETE DUSTPROOFER


-8-10m2 per litre

dependent upon porosity25 litres

Simply poured from the container, this one coat (in most cases) dustproofer dries clear. Can be used internally and externally and can be used on friable masonry and other mineral surfaces.

CHEMICAL RELEASE AGENT


-20-30m2 per litre

25 litres

- 210 litres

A blend of fatty acids in a partially evaporative carrier that provide a stain free concrete finish of the highest quality with excellent strip. Listed by WBS for drinking water projects.





ON

ST

RU

CT

ION

CH

EM

ICA

LS

KERB REPAIR


-16kg pack = 0.5m2 at

16mm16kg

A fast setting permanent repair product, which, when water is added, gives a workable concrete grey compound which sets in 20 minutes. Can be part mixed and in thicknesses of up to 30mm.

WATER LEAK PLUG


- 1m2 at 5mm 10kg

A fast setting, non-toxic cementitious compound for stopping flowing water in seconds. Mixed into a putty it is used to seal cracks, tie holes and other defects in concrete.

FLOOR REPAIR


- 1m2 at 8mm depth 16kg

A fast setting floor repair medium which when mixed is an easily worked compound to repair damaged floors. It sets in 45 minutes and can be over painted. This product is non shrinking and should be used in thicknesses between 10mm and 50mm. Can be part mixed.

EPOXy REPAIR MORTAR


- 5kg covers 10mm thick at 0.25m2

5kg

- 10kg

A three-part epoxy mortar repair compound that can be applied from 5mm to 25mm in one pass, with excellent abrasion and chemical resistance. Has a high early strength, does not need separate primer and achieves 70N/mm2 in 24 hrs.

16





ON

ST

RU

CT

ION

CH

EM

ICA

LS

MULTI GROUT


-75 bags per m3 (1m2 at

13mm)25kg

A high strength cementitious grout with excellent flowing capabilities designed to fill voids and restrained gaps without shrinking and reaching a strength of 60 N/mm2 after 28 days and yielding 13.25 litres per bag.

UNIvERSAL ADMIXTURE


-

Typically 4-5 litres per 25kg of cement

5ltr

- 25ltr

- 205ltr

A multi-use SBR admixture used to waterproof, strengthen, improve adhesion, and is also a workability aid. 4 in 1 enhances floor screeds, allowing thicknesses of 6mm whilst increasing durability. Can also be used as a slurry coat for tanking.

RESIN ANCHOR FIXING PASTE


- 150mm size will fix 12 no. 12mm diameter bolts x

100mm

150ml

- 280ml

A high strength self mixing 2 component resin fixing paste which is an adhesive compound used for fixing bolts and studs in concrete for a stress free fixing. This cartridge fits a standard skeleton gun, is pumpable, and can be used to adhere a wide range of materials to concrete.

UNIvERSAL BEDDING MORTAR


-0.5m2 at 25mm. Beds 2

no. 600 x 450mm frames, 25mm thick x 100mm wide

25kg

A high strength non shrink cement based mortar for bedding manhole cover frames, gully grids and channels, with adjustable consistency which sets in 20 minutes allowing trafficking after 1 hour - meets Highways requirements.





ON

ST

RU

CT

ION

CH

EM

ICA

LS

LIqUID WATERPROOFER


- 10m2 per litre on smooth surfaces

5ltr

- 25ltr

A general purpose ‘blackjack’ bitumen paint for waterproofing and protecting concrete and steelwork with two coats on a dry surface - the tough, flexible and impermeable coating may be over painted.

SWELLABLE STRIP AND ADHESIvE


-20mm x 7mm x 5m with

310ml cartridge310ml

This swellable hydrophilic rubber strip can swell up to 250% when in contact with water, thus stopping the passage of moisture in construction and kicker joints. It is WRAS approved, has a coating to delay swelling during placement and is held in place with a gun applied adhesive.

ELASTOMERIC BITUMEN SEALANT


- 11m of 6mm bead 310ml

A gun applied rubber waterproof compound for sealing line drainage channels, gutters and gaps, with a non setting rubber which can be applied to wet surfaces.

WATERPROOF COATING


-1-1.5kg per m2 per coat.

2 coats required25kg

A cement based, non-toxic, brush applied waterproof coating which blocks the pores in concrete, block-work masonry and renders, eliminating the passage of water and becoming an integral part of the structure. The two coat system can be applied to the negative or positive side of the structure.

18





ON

ST

RU

CT

ION

CH

EM

ICA

LS

RIW LAC Code Coverage per 1 coat Pack size

-1m2 per litre

5ltr

- 25ltr

A two coat, cold-applied liquid damp proof membrane.

RIW FLEXISEAL

Code ProductCoverage per

1 coat Pack sizes

- Primer 8m2 per litre 5/20 litres

- Flexiseal 2m2 per kilo 6/20 kg

A thixotropic urethane pre-polymer brush applied damp proof membrane.PLEASE NOTE: Primer is required

RIW HEvISEAL Code Coverage per 1 coat Pack size

-1.5m2 per litre

5 litres

- 20 litres

A cold-applied, heavy bodied damp proof membrane, which is UV resistant and dries to a uniformed black finish. The coating is a fibre and mineral filled solution of natural and petroleum bitumens in white spirit.

RIW TOUGHSEAL Code Coverage per 1 coat Pack size

- 4m2 per litre 5/20 litres

A two part polymer modified epoxide water and vapour barrier.PLEASE NOTE: 2 coats are required

RIW SHEETSEAL 226

Code Product Coverage Roll length/pack size

- Sheetseal 226 20m2 20 x 1m

- Primer 6m2 per litre 5/25 litres

A cold-applied, high density, PE film self adhesive membrane.PLEASE NOTE: Must be used with RIW Sheetseal Primer

ALL of the following products are available ex-stock.




CONCRETE CONSTRUCTION ACCESSORIES CONCRETE CONSTRUCTION ACCESSORIESW

AT

ER

PR

OO

FING

& G

AS

ME

MB

RA

NE

PROOFEX ENGAGECode Product Size

51901 Engage 1.27 x 30m

51904 Engage detail strip 200mm x 10m

53095 Proofex LM 28kg

53100 Proofex LM mesh 100mm x 50m

Pre-applied membrane which mechanically bonds to poured concrete, remaining in place if settlement of substrate occurs.

PROOFEX 3000 & PROOFEX 3000MRCode Product Size

51670 Proofex 3000 1 x 20m

51650 Proofex Primer 25 ltr

51940 Proofex Engage detailing strip 200mm x 10m

51805 Proofex 3mm protection board 1 x 2m

For basement sub-structures, foundations and buried roofs. 3000MR is a combined waterproofing and gas membrane, suitable for use in areas subject to radon, methane and carbon dioxide (CO2).

BITUTHENE 3000Code Product Size

25917 Bituthene 3000 1 x 20m

23559 B1 primer 25 ltr

797 Bituthene LM 5.7 ltr

57098 Servitape 30mm x 20m

Bituthene 3000 is a cold-applied, flexible waterproof membrane.

BITUTHENE 8000Code Product Size

10580 Bituthene 8000 1 x 20m

23560 B2 primer 25 ltr

52905 Bituthene protection board 2 x 1m

21257 Hydroduct 200mm 32 x 1.25m

21247 Hydroduct 220mm 32 x 1.25m

Bituthene 8000 is a cold-applied, flexible waterproof membrane.

PLEASE NOTE:We stock the full range of FOSROC products.

PLEASE NOTE:We stock the full range of GRACE products.

Supplier of concrete accessoriesand specialist products

T Wolverhampton 01902 353161T London 0208 345 5850 E [email protected]

Stowheath Industrial Estate, Monmore RoadWolverhampton, West Midlands WV1 2TZ

Midland Construction Supplies Limited is a Burdens partner company. Registered Office: 3 Brook Office Park, Folly Brook Road, Emersons Green, Bristol BS16 7FL. Registered in England Company No. 03593372

Supplier of concrete accessories and specialist products A5 Mini Brochure.pdf · Supplier of...

Documents

Transcript of Supplier of concrete accessories and specialist products A5 Mini Brochure.pdf · Supplier of...