SUPERVISOR DECLARATIONeprints.utem.edu.my/16514/1/The Effect Of Coupling... · Penemuan ini...
Transcript of SUPERVISOR DECLARATIONeprints.utem.edu.my/16514/1/The Effect Of Coupling... · Penemuan ini...
SUPERVISOR DECLARATION
“I hereby declare that I have read this thesis and in my opinion this thesis is
sufficient in term of scope and quality for the award of the degree of Bachelor of
Mechanical Engineering (Structure & Material).”
Signature : …………………………
Supervisor :DR. SITI HAJAR BINTI SHEIKH MD.FADZULLAH
Date : …………………………
THE EFFECT OF COUPLING AGENT ON THE MECHANICAL
PROPERTIES OF PLA-BASED POLYMER COMPOSITES
NUR AMARINA BINTI MAHMOOD
This report is written as a partial fulfilment of terms in achieving the award for
Bachelor of Mechanical Engineering (Structure & Material)(Hons.)
Faculty of Mechanical Engineering
Universiti Teknikal Malaysia Melaka
JUNE 2015
ii
DECLARATION
“I hereby declare that the work in this thesis is my own except for summaries
quotation which have been duly acknowledged”
Signature :......................................................
Author : NUR AMARINA BINTI MAHMOOD
Date :......................................................
iii
Thank you a lot to all of my family especially to my father and my mother for
helping and support to finish this thesis.
Mahmood Bin Ibrahim
Laila Dahalan
iv
ACKNOWLEDGEMENT
Praise to Allah the Almighty, with His will I had finally completed preparing for this
FYP thesis. I would like to take this opportunities to thank to my supervisor Dr Siti
Hajar Binti Sheikh Md Fadzullah for her never ending support, guidance, and
advices during completion of this thesis.
My appreciation also goes to my parents for their support towards me to successfully
done this project in order to graduate from UTeM. Last but not least, my appreciation
goes to those who had involve directly or indirectly in helping me to complete this
thesis.
v
ABTRACT
This research describes biodegradable polymers using composites PLA as a
matrix and reinforced with pineapple leaf fibres (PALF) to produce environmentally
friendly “green composites”. To-date, there has been numerous published papers,
highlight the potential composite of such materials to replace the synthetic composites.
However, these type of biocomposites is well-known to be brittle in nature as well as
possess low tensile strength and impact properties in comparison to that of the
synthetic polymer composites. Hence, this research aims to investigate the effect of
coupling agent in promoting improved bond between the fibre reinforcement and the
polymer matrix, which enhanced the mechanical properties of biocomposites. In this
research, pineapple leaf are considered natural fibre reinforcement and polylactid acid
(PLA) as a biodegradable polymer. Mechanical properties have been conducted and
analysed by characterised under tensile, flexural and impact loading according to the
American Society for Testing and Materials (ASTM). Findings show that PALF
reinforced PLA composites possessed superior properties in comparison to that of the
plain PLA. In addition, the effect of using alkaline pre treatment improved the bonding
forms at the fibre/matrix interface.
vi
ABSTRAK
Penyelidikan ini memfokuskan kepada bahan polimer terbiodegrasi
menggunakan bahan PLA sebagai satu matrik dan diperkukuhkan dengan gentian daun
nenas untuk menghasilkan bahan biokomposit yang bersifat mesra alam. Sehinnga
kini, telah banyak kajian yang telah dijalankan yang menekankan bahawa komposit ini
boleh menggantikan polimer sintetik. Walaubagaimanapun, biokomposit ini terkenal
mempunyai sifat rapuh dan serta mempunyai tegangan yang rendah dan hentaman
berbanding dengan sintetik polimer. Maka, penyelidikan ini bertujuan untuk menyiasat
kesan agent pengupelan dalam mempromosikan ikatan yang lebih baik antara matrik
polimer dan gentian nenas yang meningkatkan ciri-ciri mekanikal komposit. Dalam
penyelidikan ini, PLA digunakan sebagai matrik dan daun nenas sebagai gentian untuk
menghasilkan polimer terbiodegrasi. Sifat mekanik telah dijalankan dan dianalisa di
bawah tegangan,, lenturan dan hentaman mengikut American Society Testing
Materials (ASTM). Penemuan ini menunjukkan bahawa bahan komposit PLA
diperkuat gentian nenas mempunyai ciri-ciri yang hebat berbanding dengan bahan
polimer PLA yang tidak diperkuat pada antara muka di antara bahan matrik dan
gentian nenas. Hal ini turut dipengaruhi oleh peningkatan yang ditingkatkan pada
antara muka dia antara bahan matrik dan gentian dengan proses pra-rawatan alkali
dengan menggunakan natrium hidroksida.
vii
TABLE OF CONTENT
CHAPTER TITLE PAGE
DECLARATION ii
DEDICATION iii
ACKNOWLEDGEMENT iv
ABSTRACT v
ABSTRAK vi
TABLE OF CONTENT vii
LIST OF TABLES x
LIST OF FIGURES xi
CHAPTER I INTRODUCTION 1
1.1 Background 1
1.2 Objectives 2
1.3 Scope of Research 3
1.4 Problem Statement 3
1.5 Planning And Execution 4
CHAPTER II LITERATURE REVIEW 6
2.1 Introduction to Composite Material 7
2.2 Polymer Matrix Composites 8
2.3 Biocomposites 10
2.3.1 Available bio-composites and their benefits 11
viii
2.3.2 Matrix polymer matrix 12
2.3.3 Natural fibre reinforcement 13
2.4 Mechanical Properties if biocomposites 14
2.4.1 Tensile Properties of PALF reinforced PLA composites 15
2.4.2 Flexural Properties of PALF reinforced PLA composites 17
2.4.3 Impact properties 18
2.5 Chemical Treatment 20
2.5.1 Alkaline Treatment 20
2.5.2 Silane treatment 21
2.6 Summary 21
CHAPTER III METHODOLOGY 23
3.1 Introduction 23
3.2 Raw materials 25
3.2.1 Polylactid acid (PLA) 25
3.2.2 Pineapple leaf 26
3.3 Fabrication process 28
3.3.1 Preparation of PLAF 29
3.3.2 PALF-PLA Composite Preparation 30
3.3.3 Testing Sample Preparation 33
3.4 Testing Method 34
3.4.1 Tensile testing 34
3.4.2 Flexural testing 36
3.4.3 Impact Testing 38
3.4.4 Morphology studies 40
ix
CHAPTER IV RESULTS AND DISCUSSION 42
4.1 Introduction 42
4.2 Tensile Properties 42
4.2.1 Failure mode on tensile sample 47
4.3 Flexural Properties 49
4.4 Impact Properties 52
4.4.1 Failure mode on impact testing 55
4.4 Morphological Study 56
CHAPTER V CONCLUSION AND RECOMMENDATION 60
5.1 Conclusion 60
5.2 Recommendation 61
REFERENCE 62
x
LIST OF TABLES
NO TITLE PAGE
1.1 Gantt chart PSM I. 4
1.2 Gantt chart PSM II. 5
2.1 Advantages and disadvantages of composites. 8
2.2 Advantage and disadvantage of thermosets and 9
thermoplastic
2.3 Properties of PLA and PLAF 15
2.4 Average value of flexural strength and modulus of elastic 21
3.1 PLA Ingeo Biopolymer 6100D Technical Data Sheet 26
4.1 The results of tensile testing properties obtained from 44
the tensile test on the PLA sample.
4.2 The results of tensile properties from tensile test on 44
the composites samples.
4.3 Comparison data between experimental value, theoretical 45
and references.
4.4 Observation the failure mode of Plain PLA. 48
4.5 Observation the failure mode of composites. 49
4.6 The results of flexural properties obtained from flexural 50
test on pure PLA samples.
4.7 The results of flexural testing obtained on composites 50
samples.
4.8 Comparison data with experimental value and references. 50
4.9 The results of impact testing obtained on pure PLA 53
xi
NO TITLE PAGE
4.10 The results of tensile testing obtained on composites 53
samples.
4.11 Comparison data between experimental value and 53
literature review.
4.12 Observation the failure mode of Pure PLA. 55
4.13 Observation the failure mode of composites. 56
5.1 Summary of main findings from the experimental 61
work.
xii
LIST OF FIGURES
NO TITLE PAGE
2.1 Development of Biocomposites from Renewable Resource 10
2.2 Development process and value chain of biocomposites industry in
Malaysia 12
2.3 Polylactic acid (PLA) polymerization 12
2.4 Categories of Natural Fibres 14
2.5 Tensile properties of PLAF/PLA composites showing tensile
strength and tensile modulus 16
2.6 Elongation at break of PALF/PLA composites 16
2.7 Flexural properties of 40 wt% surface-treated PALF fibbers
compared to untreated PALF fibres reinforced composites 17
2.8 Stress–strain curves: (a) neat PLA (b) PLA/PALF (60/40), (c)
PLA/PALFNA(60 wt%/40 wt%) , (d) PLA/PALFSI (60 wt%/40
wt%) and (e) PLA/PALFNASI 18
2.9 Notched Izod impact strength of 40 wt% surface-treated PALF fibres
compared to untreated PALF fibres reinforced composites 19
2.10 Dependence of impact strength on the content for PLA/PALF
composites: (i) PLA/PALF, (ii) PLA/PALFNA (iii) PLA/PALFSI
and (iv) PLA/PALFNASI. 19
xiii
3.1 Flow chart of the project research 24
3.2 PLA pellet 25
3.3 Pineapple leaf as natural fibre 27
3.4 Fabrication process of the PALF reinforced PLA composites 28
3.5 PLAF immersed in 5% concentration of NaOH 29
3.6 PLAF was dried 30
3.7 Graph of temperature vs Time for hot press machine during
fabrication process. 31
3.8 Mould dimension 180mm x 180mm 31
3.9 Hot Isostatic Press Machine 32
3.10 Composite Plate 32
3.11 Shearing machine to cut sample inti size 33
3.12 Detail dimension on tensile specimen 34
3.13 Universal Testing Machine for Tensile and Flexural Testing 35
3.14 (a) Pure PLA test that have been failed (b) Composites that have
been failed 36
3.15 Allowable Range of Loading Nose and Support Radii in ASTM
D790 37
3.16 Charpy impact tester 40
3.17 Dimension of the charpy impact test 40
3.18 Mini sputter Coater machine 40
3.19 The samples that have been coated 41
3.20 Scanning Electron Microscope (SEM) 41
4.1 Stress-strain Curves for plain PLA 43
4.2 Stress-strain Curves for PALF reinforced PLA composite 43
xiv
4.3 Graph of tensile strength versus type of samples 45
4.4 Graph of Young’s modulus versus type of samples 46
4.5 Graph of comparison on the tensile strength for composites treated
with NaOH, treated with silane coupling agent and theoretical 46
4.6 Graph of comparison on Young’s Modulus for composites treated
with NaOH and theoretical. 47
4.7 Graph of Flexural strength versus type of samples 51
4.8 Graph of flexural modulus versus type of samples 51
4.9 Graph of comparison on the flexural strength for composites treated
with NaOH and treated with silane coupling agent 51
4.10 Graph of comparison on the flexural modulus for composites treated
with NaOH and treated with silane coupling agent 52
4.11 Graph of energy absorbed versus type of sample 54
4.12 Graph of comparison on the energy absorbed for composites
between treated with NaOH and treated with silane coupling agent54
4.13 The failure mode of the plain PLA under tensile loading 57
4.14 The failure mode of the composites under tensile loading 58
4.15 The failure mode of the composites under impact loading 58
4.16 Micrograph of PALF reinforced PLA composite (30wt% PALF) 59
1
CHAPTER I
INTRODUCTION
1.1 BACKGROUND
The growing environmental awareness, the concern for environmental
sustainability and the growing wasted problem is increased year by year. The
production of fuel-derived plastics is often harmful to the environment [1]. For
example automotive applications based on natural fibres with polypropylene as matrix
material are very common today [2]. Limited studies have been carried out on
composites with matrices, which originate from renewable raw materials. There are
many different polymers of renewable material. For example, polylactic acid, cellulose
esters, poly hydroxyl butyrates, starch and lignin based plastics, are some of the
renewable polymer materials or biopolymer [3].
The use of natural plant fibres as a reinforcement in fibre-reinforced plastics
(FRP) to replace synthetic fibres such as glass is receiving attention, because of
advantages such as low density, high specific strength and renewability. The
development of biodegradable composite materials using natural fibres such as flax,
bamboo, pineapple, jute, and kenaf as a reinforcement for biodegradable plastics have
examined molding conditions, mechanical properties, and interfacial bonding.
2
However, the processes involved in using natural plant fibres as a reinforcement are
different from those using industrial products such as glass and carbon fibres. The
shape, size, and strength of the natural plant fibres may vary widely depending on
cultivation environment, region of origin, and other characteristics. Besides, these
features of the natural fibres are likely to influence the mechanical properties of the
natural fibre-reinforced plastics [4].
Coupling agents are used to provide a stable bond between two otherwise non-
bonding and incompatible surfaces. In reinforced and filled plastics, the improved
bond between the fibrous or particulate inorganic component and the organic matrix
polymer results in greater composite strength [5]. Coupling agent are commonly
employed to treat fibre surfaces in order to improve interfacial adhesion within
composites which can also in some cases improve their initial mechanical properties.
Coupling agent investigated include, but are not limited to; conventional silanes,
various phosphonic acids, poly-(HEMA), zirconate and titanate coupling agents [6].
1.2 OBJECTIVES
The objectives of this research are listed as below:
i. To develop PLA-based polymer composites using pineapple leaf fibre as
reinforcement.
ii. To study the effect of using chemical coupling agent on the bonding
mechanism present.
iii. To access the effect of using chemical coupling agent on the tensile and
impact properties of the degradable polymer composites.
3
1.3 SCOPE OF RESEACRH
The scopes of this research are listed as below:
i. selection of materials and coupling agent for the composites.
ii. fabrication of biodegradable polymer composites test panels.
iii. mechanical testing.
iv. physical testing.
v. surface morphology.
1.4 PROBLEM STATEMENT
The developing environmental awareness and new rules and regulations are
forcing the industries to seek more ecologically friendly materials for their products
[3]. There are many different polymers are renewable materials for example polylactic
acid, starch, cellulose esters and lignin based plastics. The problems with these
polymers have been poor commercial availability, poor processability, low toughness,
high price and low moisture stability.
Biodegradable polymers such as PLA, cellulose esters and starch can be
reinforced with these bio-based fibres such as kenaf, flax, bamboo and sisal to produce
environmentally friendly “green compo-sites” [7]. However, this type of
biocomposites is well-known to be brittle in nature as well as possess low tensile
strength and impact properties in comparison to that of the synthetic polymer
composites [8]. Hence, this research aims to investigate the effect of coupling agent in
promoting improved bond between the fibre reinforcement and the polymer matrix,
which is expected to enhance the mechanical properties of biocomposites.
4
1.5 PLANNING AND EXECUTION
Table 1.1: Gantt chart PSM I
Week 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Selection of PSM title
Literature Review
Design of Experiment
Draft of PSM I Poster
Submission of poster
Characterisation of
raw materials
Preliminary data
analysis
PSM I report writing
Submission of PSM I
report
PSM I seminar
Task
5
The Gantt chart shows project the planning for Final Year Project ( PSM I)
which commences in September 2014. The research activities include selection of
research title and approval by the respective lecturer, literature review that is
continuous throughout the studies, design of experiment, as well as establishing the
methodology. This is followed by poster preparation and submission. After that
fabrication process. Once required results and analysis, report PSM I will be submitted
and have PSM I seminar.
Table 1.2: Gantt chart PSM II
Week 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Material Review
Design Test
Model
Experimental
Work
Fabrication
Mechanical Test
Analysis
Result &
Discussion
Submission of
PSM II report
PSM II seminar
Task
6
CHAPTER II
LITERATURE REVIEW
2.1 INTRODUCTION TO COMPOSITE MATERIAL
A composite material is made by combining two or more materials. The two
materials work together to give the composite unique properties. However, within the
composite it can easily tell the different materials apart as they do not dissolve or blend
into each other [9]. Composites have become an integral part of our day-to-day life
and can be discovered all over the place, for example rubber tire, spacecraft, asphalt,
etc. Composites have been around for a long time with the classic example of bricks
made from straw and mud. Another example is the Mongol bow which was constructed
out of animal tendons, wood, and silk bonded together with an adhesive [10].
7
Nature also has its own composites in the form of wood, teeth, bones, muscle
tissue, etc. In general the composite materials consist of a matrix reinforced with fibres.
The biggest advantage of modern composite materials is that they are light as well as
strong. By choosing an appropriate combination of matrix and reinforcement material,
a new material can be made that exactly meets the requirements of a particular
application. Composites also provide design flexibility because many of them can be
moulded into complex shapes. The downside is often the cost. Although the resulting
product is more efficient, the raw materials are often expensive [11].
High performance fibre reinforced composite materials are comprised of high
strength and modulus fibres, embedded in, or bonded to, a matrix, with a distinct
interface between them. In a composite, the fibre, as well as the matrix, retain their
physical and chemical identities, but still provide a combination of properties that
cannot be achieved with either of the constituents alone. In general the fibres play the
role of load bearer. The matrix, while keeping the fibres in the desired location and
orientation, act as a load transfer agent and protects the fibres from external conditions
such as chemicals, heat and moisture [12].
Composites can be classified based on the type of fibres or matrix used. Based
on the type of fibres, composites can be further classified as continuous fibre
reinforced composite and short fibre reinforced composites. Based on the type of
matrix, composites can be broadly classified into three categories, there are metal
matrix composites, ceramic matrix composites and polymer matrix composites [11].
8
Table 2.1: Advantages and disadvantages of composites [11].
Advantages Disadvantages
Weight reduction Cost of raw materials and
fabrication
High strength or stiffness to weight
ratio
Transverse properties may be weak
Tailorable properties: can tailor
strength or stiffness to be in the load
direction
Matrix weakness, low toughness
Redundant load paths (fibre to fibre) Matrix subject to environmental
degradation
Longer life (no corrosion), better
fatigue life
Difficult to attach
Lower manufacturing costs Non-destructive testing tedious
2.2 POLYMER MATRIX COMPOSITES
Polymer matrix composites are widely used and sub-divided into two classes
based on the type of matrix polymer are thermoplastic or thermoset. Thermoplastics
consists of linear or branched chain molecules having strong intramolecular bonds but
weak intermolecular bonds. They can be reshaped by application of heat and pressure
and are either semicrystalline or amorphous in structure. Examples include
polyethylene, polypropylene, polystyrene, nylons, polycarbonate, polyacetals,
polyamide-imides, polyether ether ketone, polysulfone, polyphenylene sulfide,
polyether imide, and so on. [8].
9
Thermoset have cross-linked or network structures with covalent bonds with
all molecules. They do not soften but decompose on heating. Once solidified by cross-
linking process they cannot be reshaped. Common examples are epoxies, polyesters,
phenolics, ureas, melamine, silicone, and polyimides [14].
The difference between thermoplastics and thermosets plastics is that
thermoplastics become soft, remoldable and weldable when heat is added. Thermoets
plastics however cannot be welded or remolded when heated, simply burning instead.
On the other hand, once a thermosets is cured it tends to be stronger than a
thermoplastic [14].
Table 2.2: Advantages and disadvantage of thermosets and thermoplastics
[14].
Property Thermosets Thermoplastics Formulations Complex Simple Melt viscosity very low High Fiber Impregnation Easy Difficult Prepeg tac good None Prepag drape good none to fair Prepag stability good Excellent Processing cycle Long short to long Processing temperature low to moderate High Processing pressure low to moderate High Fabrication cost high Low Mechanical properties fair to good fair to good 54 to 93 °C.hot/wer Environmental durability good Unknown Solvent resistance excellent poor to good Damage tolerance poor to excellent fair to good Database very large Small