Embed Size (px)
Transcript of SUNNYSIDE ACETONE
Sunnyside Corporation 3/2009
DESCRIPTION PRODUCT IMAGE SAFETY INFORMATION
ITEM NUMERS & SIZES
Pint Quart 1-Gallon 2.5-Gal. 5-Gal. 55-Gal.
84016 84032 840G1 840G3 840G5 84055
HAZARDOUS INGREDIENTS PRODUCT APPLICATION
Ingredient CAS# Percent
Acetone 67-64-1 100%
PHYSICAL PROPERTIES TEST METHOD
Typical Properties Results ASTM Applied
GRAVITY, (60 F)
SPECIFIC 0.792 D-1298
DENSITY (Lb./GAL) 6.6
DISTILLATION RANGEE IBP F 133 D-86
Sunnyside Acetone is a very fast evaporating, extremely flammable solvent. It
can be used to dissolve many natural and synthetic gums, waxes, oils and
dyes. It will readily mix with water, alcohols, esters, ethers and other organic
ACETONE TECHNICAL DATA SHEET 840
Acetone can be used for thinning epoxies, lacquers and adhesives, as well as
polyester resins used in fiberglass boat and auto repairs. When cleaning
application equipment or when using for any other purpose, prevent flammable
vapor buildup by limiting amount used to a few ounces at a time.
Page 1 of 1
DISTILLATION RANGEE IBP F 133 D-86
FREEZING POINT, F (C) -139
KAURI BUTANOL (Kb) VALUE D-1133
ANILINE POINT, F D-611
FLASH POINT, T.C.C. F 0 D-56
FLAMMABLE LIMITS IN AIR, % BY VOLUME
LOWER, AT 100F (38C) 2.6
UPPER, AT 200F (93C) 12.8
AUTOIGNITION TEMPERATURE, F (C) 869 D-1255
COLOR (Pt-Co)t-Co) Max. 5 D-156
DOCTOR TEST D-484
CORROSION, 3 HRS. @ 212 F D-130
NON-VOLATILES, g/100ml D-1353
ACIDITY (as Acetic Acid) 0.002 max. D-847
ALKALINITY (AS NH3, WT%) 0.001 max. D-1614
EVAPORATION RATE Slower than ether
APPEARANCE Clear, water-white
ODOR Characteristic, Nonresidual D-1296
VAPOR PRESSURE, mm Hg @ 20 C 213
REFRACTIVE INDEX, @ 20 C D-1218
SULFUR CONTENT, PPM D-1266
PURITY, by G.C., Wt% 99.5 Min.
WATER CONTENT, Wt% 0.5 Max. D-1364
WATER MISCIBILITY Complete D-1722
DOT SHIPPING NAME Acetone
DOT CLASSIFICATION Hazard Class III
SHIPPING Wt. at 20 C 6.6
V.O.C. (g/L) 0-Exempt
See MSDS sheeet for additional Health, Safety, Handling and Regulatory
Information available on our website at
These properties are repesentative of typical inspections. They do not
constitute product specifications. Consult MSDS sheet for additional
Page 1 of 1
MATERIAL SAFETY DATA SHEET(Prepared According to 29 CFR 1910.1200)
SECTION 1 - PRODUCT IDENTIFICATION Distributor Emergency PhoneCustom Solutions 800-309-5869Address 900 E. 103rd Street, Chicago, IL 60628
Stainless Steel PolishTrade Name Product TypeBRILLIANCE
SECTION 2 - INGREDIENTSCHEMICAL NAME/COMMON NAME CAS NO. WT. %(opt) TLV(Source) TITLE III, SECT. 313
Mineral Spirits 64741-65-7 25 - 30 100ppm(TWA) NOIsoparaffinic Solvent 64741-66-8 40 - 50% 400 ppm (TWA) NO
MATERIAL SAFETY DATA SHEET
1. Product and Company IdentificationMaterial name C6 Epoxy AdhesiveVersion # 01Revision date 06-09-2010CAS # MixtureProduct Code C6Product use Concrete anchoring adhesive.Manufacturer/Supplier ITW Red Head
2171 Executive Drive, Suite 100Addison, IL 60101 USTelephone Number: (630) 350-0370Contact Person: Andrew Rourke
Emergency CHEMTREC: (800) 424-9300
2. Hazards IdentificationPhysical state Liquid.Appearance Paste.Emergency overview DANGER!
Causes skin and eye burns. Causes severe respiratory tract irritation. Harmful if absorbed throughskin or swallowed. May cause sensitization by skin contact. Prolonged exposure may causechronic effects.
OSHA regulatory status This product is considered hazardous under 29 CFR 1910.1200 (Hazard Communication).Potential health effects
Routes of exposure Inhalation. Ingestion. Skin contact. Eye contact.Eyes Causes eye burns. Risk of corneal damage. Contact may cause irritation, redness, tearing,
blurred vision and/or burns.Skin Causes skin burns. Harmful if absorbed through the skin. May cause sensitization by skin contact.
Contact may cause irritation, redness and/or drying.Inhalation Causes severe respiratory tract irritation. Vapors irritate the respiratory system, and may cause
coughing and difficulties in breathing.Ingestion Harmful if swallowed. Ingestion may produce burns to the lips, oral cavity, upper airway,
esophagus and possibly the digestive tract.Target organs Eyes. Skin. Respiratory system. Lungs.Chronic effects Overexposure can cause lung damage - pulmonary toxin.Potential environmental effects The product contains a substance which is toxic to aquatic organisms and which may cause
long-term adverse effects in the aquatic environment.
Components CAS # Percent
3. Composition / Information on Ingredients
25068-38-6 60 - 80Bisphenol A Diglycidyl Ether Resin (Part A)
Trade Secret 20 - 40Mercaptan/Amine Polymer Blend (Part B)
90-72-2 Trade Secret2,4,6-Tris(dimethylaminomethyl) Phenol (Part B)
67-63-0 Trade SecretIsopropanol (Part B)
4. First Aid MeasuresFirst aid procedures
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, ifpresent and easy to do. Continue rinsing. Get medical attention immediately.
C6 Epoxy Adhesive4416 Version #: 01 Revision date: 06-09-2010 Print date: 06-09-2010
CPH MSDS NA
1 / 7
Skin contact Immediately flush with plenty of water for at least 15 minutes while removing contaminatedclothing and shoes. Get medical attention immediately. Wash clothing separately before reuse.Destroy or thoroughly clean contaminated shoes.
Inhalation Move to fresh air. If breathing is difficult, give oxygen. Get medical attention.Ingestion Rinse mouth thoroughly. Do not induce vomiting. If vomiting occurs, keep head low so that
stomach content does not get into the lungs. Never give anything by mouth to a victim who isunconscious or is having convulsions. Get medical attention immediately.
Notes to physician Keep victim under observation. In case of shortness of breath, give oxygen. Symptoms may bedelayed.
General advice Take off contaminated clothing and shoes immediately. Ensure that medical personnel are awareof the material(s) involved, and take precautions to protect themselves. Show this safety datasheet to the doctor in attendance. Wash contaminated clothing before re-use.
5. Fire Fighting MeasuresFlammable properties Not flammable by OSHA criteria. Material may burn but not ignite readily.Extinguishing media
Water. Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Protection of firefightersProtective equipment andprecautions for firefighters
Firefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, SCBA. Move containers from fire areaif you can do so without risk. Cool containers exposed to flames with water until well after the fireis out. Water runoff can cause environmental damage.
Special protective equipmentfor fire-fighters
Wear full protective clothing, including helmet, self-contained positive pressure or pressuredemand breathing apparatus, protective clothing and face mask.
Specific methods In the event of fire and/or explosion do not breathe fumes.Hazardous combustionproducts
Carbon monoxide. Carbon Dioxide. Nitrogen oxides (NOx). Hydrogen chloride. Sulfur oxides.
6. Accidental Release MeasuresPersonal precautions Keep unnecessary personnel away. Local authorities should be advised if significant spillages
cannot be contained. Keep upwind. Keep out of low areas. Ventilate closed spaces beforeentering them. Do not touch damaged containers or spilled material unless wearing appropriateprotective clothing. See Section 8 of the MSDS for Personal Protective Equipment.
Environmental precautions Prevent further leakage or spillage if safe to do so. Do not contaminate water.Methods for containment Stop leak if you can do so without risk. Dike the spilled material, where this is possible. Collect
spillage. Prevent entry into waterways, sewers, basements or confined areas.Methods for cleaning up Small Spills: Absorb spill with vermiculite or other inert material. Clean surface thoroughly to
remove residual contamination. This material and its container must be disposed of as hazardouswaste. Should not be released into the environment.
Large Spills: Use a non-combustible material like vermiculite, sand or earth to soak up the productand place into a container for later disposal. Prevent product from entering drains. Do not allowmaterial to contaminate ground water system.
Other information Clean up in accordance with all applicable regulations.
7. Handling and StorageHandling Wear personal protective equipment. Avoid breathing vapor. Do not get in eyes, on skin, on
clothing. Avoid prolonged exposure. Do not taste or swallow. Use only with adequate ventilation.Wash thoroughly after handling. When using, do not eat, drink or smoke. Avoid release to theenvironment.
Storage Keep container tightly closed. For maximum shelf life, store between 4.4C (40F) to 26.7C(80F). Do not store above 43.3C (110F). Keep away from food, drink and animal feedingstuffs.Keep out of the reach of children.
8. Exposure Controls / Personal ProtectionOccupational exposure limits
Components Type ValueIsopropanol (Part B) (67-63-0) 400 ppmSTEL