Stramit Patio Roofing Spans Tablefor pitched roof. • The number of supports (beams or purlins)...

1

Stramit® Patio Roofing Span Tables

2

How to use the tables

Step 1Determine whether the patio is monoslope or pitched.

If attached to a house, determine the average height of the roof above ground (h) and the height of the attached patio (hc) in metres.

Step 2Based on the intended usage, determine whether the patio will be “blocked under” or “empty under”. If in doubt, assume “blocked under”.

Empty Under: Goods or materials stored under the patio blocking less than 50% of the cross-sectional area exposed to the wind.

Blocked Under: Goods or materials stored under the patio blocking more than 75% of the cross-sectional area exposed to the wind.

Step 3By referring to the selection tables, determine which of the span tables A to K is appropriate.

Step 4Using the appropriate span table (A to K) and the AS4055 wind classification for the location and topography, determine the span (spacing between supports) for the selected roofing profile and thickness.

Stramit® Patio Roofing Profiles

Width

Length

Patio height (hc)

Average roof height (h)

Stramit Sunset® Patio Roof Panel

Stramit Longspan® Cladding

Stramit Monoclad® Cladding

Stramit® Corrugated Cladding

Stramit Speed Deck Ultra® Concealed Fixed Decking

Important Notice Foot traffic loadsThe tables show maximum spans (mm) for patio applications, with limited foot traffic load.

During installation and maintenance, boards or ladders should be placed appropriately to distribute load.

Stramit strongly recommends that measures be taken to reduce the risk of foot traffic damage, such as a “No Foot Traffic” notice or sticker, available on request.

3

For attached patios, use the selection tables below to choose the appropriate span table. For free-standing canopies of any height up to 3.2m, use the span table marked below with an asterisk (*).

Monoslope – empty underAverage Roof Height (h)

Patio Height (hc) 3 ≤ h < 4 4 ≤ h ≤ 5 5 < h ≤ 6.5

hc ≤ 2.3 D* A A

2.4 ≤ hc < 2.8 F C A

2.8 ≤ hc ≤ 3.2 G E B

Monoslope – blocked underAverage Roof Height (h)


hc ≤ 2.3 H* H H

2.4 ≤ hc < 2.8 H H H

2.8 ≤ hc ≤ 3.2 H H H

Pitched Roof – empty underAverage Roof Height (h)


hc ≤ 2 .3 J* J J

2.4 ≤ hc < 2.8 F J J

2.8 ≤ hc ≤ 3.2 G E J

Pitched Roof – blocked underAverage Roof Height (h)


hc ≤ 2.3 K* K K

2.4 ≤ hc < 2.8 K K K

2.8 ≤ hc ≤ 3.2 K K K

Design Notes• Span tables are based on patio height and average

roof heights as specified in the empty under and blocked under selection tables. For heights outside these ranges, contact Stramit for further information.

• Maximum patio height (hc) is 3.2m.• Average roof height between 3m and 6.5m

(3m ≤ h ≤ 6.5m).• Patio height (hc) must always be less than roof

height (h).• Patio width is no less than 2.1m and length is no less

than 3.5m.• Maximum roof slope is 5° for monoslope and 22.5°

for pitched roof.• The number of supports (beams or purlins) affects

the allowable span length. Data is given in each table for:

Single Span: Two supports, one at each end Double Span: Three equi-spaced supports Equal Spans: Four or more equi-spaced supports.

MONOSLOPE PITCHED

SINGLE SPAN

Span

DOUBLE SPAN

Span Span

EQUAL SPAN

SpanSpan Span

MONOSLOPE PITCHED

SINGLE SPAN

Span

DOUBLE SPAN

Span Span

EQUAL SPAN

SpanSpan Span

Stramit® Patio Roofing Selection Tables

Stramit Building Products manufactures a range of roofing profiles for patio applications, offering a wide choice of styles and a high quality finish.

Stramit® patio roofing makes it easy to create elegant verandas, patios, barbecue areas and carports.

Now Stramit has issued technical data tested to Australian Standards to accompany these products.

The span tables in this guide are for domestic applications in non-cyclonic regions. For commercial and cyclonic applications, contact Stramit for further information.

4

Step 1For a monoslope patio roof attached to a house, take measurements of the average roof height of the house ‘h’ and height of the patio ‘hc’. Assume that: h = 5m hc = 2.5m

Step 2Assume that the patio will be used as an outdoor entertainment area and that the cross-sectional blockage will be less than 50%. Therefore, the “Empty Under” table is applicable.

Step 3Reading off the “Empty Under” table, with h = 5m, hc = 2.5m, span table C will be used to determine the spans.

Step 4

Assume the wind classification for the area is N1 and the roofing profile is Stramit® Corrugated cladding 0.48mm BMT thickness, in a single span configuration. From span table C, the maximum allowable single span is 2160mm.

Reading the span tables

Example

Stramit® Patio Roofing Span Tables

MAXIMUM SPAN LENGTH (mm)

SINGLE DOUBLE EQUAL

WIND CLASSIFICATION

N1 N2 N3 N4 N5 N6 N1 N2 N3 N4 N5 N6 N1 N2 N3 N4 N5 N6

Stramit Sunset® 0.42 2 1° 4430 4430 3600 2620 ‒ ‒ 4500 4500 3600 2240 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒

Stramit Speed Deck Ultra®

0.42 3 1° 3000 3000 3000 2840 2580 2130 3000 3000 3000 2890 2380 1840 2780 2780 2670 2460 2180 1740

0.48 3 1° 3000 3000 3000 2890 2660 2270 3000 3000 3000 2980 2550 1970 2800 2800 2710 2520 2270 1870

Stramit Longspan®

0.42 3 1.5° 3000 3000 2970 2560 ‒ ‒ 3000 3000 3000 2460 1860 1200 3000 3000 2960 2250 1610 ‒

0.48 3 1.5° 3000 3000 3000 2860 2430 ‒ 3000 3000 3000 2990 2300 1890 3000 3000 3000 2750 2100 1600

Stramit Monoclad®

0.42 4 2° 2910 2910 2590 2270 ‒ ‒ 3000 3000 3000 2420 1910 1590 3000 3000 2830 2390 1940 1640

0.48 4 2° 2980 2980 2710 2440 2170 ‒ 3000 3000 3000 2830 2500 2200 3000 3000 2830 2580 2300 2030

Stramit® Corrugated

0.42 3 5° 2190 2190 ‒ ‒ ‒ ‒ 2680 2680 2320 1860 1510 1170 2580 2580 2190 1720 1380 960

0.48 3 5° 2380 2380 ‒ ‒ ‒ ‒ 2970 2970 2540 2110 1640 1180 2800 2800 2420 1950 1450 1090

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPE

A


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 4260 4260 3170 2370 ‒ ‒ 4500 4500 3050 1910 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2960 2750 2420 ‒ 3000 3000 3000 2760 2110 1640 2750 2750 2600 2370 2030 1520

0.48 3 1° 3000 3000 3000 2820 2550 ‒ 3000 3000 3000 2860 2260 1750 2780 2780 2650 2440 2150 1640

Stramit Longspan®

0.42 3 1.5° 3000 3000 2840 2370 ‒ ‒ 3000 3000 2950 2250 1600 ‒ 3000 3000 2670 2030 1300 ‒

0.48 3 1.5° 3000 3000 3000 2720 2240 ‒ 3000 3000 3000 2740 2090 1590 3000 3000 3000 2480 1930 1320

Stramit Monoclad®

0.42 4 2° 2800 2800 2470 2150 ‒ ‒ 3000 3000 2920 2210 1750 1470 2970 2970 2740 2210 1780 1510

0.48 4 2° 2900 2900 2620 2340 ‒ ‒ 3000 3000 3000 2710 2370 2050 2970 2970 2750 2480 2180 1900


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 2570 2570 2190 1720 1370 ‒ 2450 2450 2030 1610 1220 780

0.48 3 5° 2270 2270 ‒ ‒ ‒ ‒ 2790 2790 2410 1940 1450 1090 2650 2650 2260 1760 1230 990

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEB

Monoslope – empty underAverage Roof Height (h)

Patio Height (hc) 3 ≤ h < 4 4 ≤ h ≤ 5 5< h ≤ 6.5

hc ≤ 2.3 D A A

2.4 ≤ hc < 2.8 F C A

2.8 ≤ hc ≤ 3.2 G E B

5


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 4040 4040 2890 2180 ‒ ‒ 4330 4330 2630 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2910 2670 2200 ‒ 3000 3000 3000 2630 1910 1470 2720 2720 2540 2270 1800 1360

0.48 3 1° 3000 3000 2950 2740 2340 ‒ 3000 3000 3000 2740 2030 1580 2750 2750 2600 2360 1950 1460

Stramit Longspan®

0.42 3 1.5° 3000 3000 2720 2200 ‒ ‒ 3000 3000 2690 2050 1330 ‒ 3000 3000 2460 1820 980 ‒

0.48 3 1.5° 3000 3000 2980 2580 ‒ ‒ 3000 3000 3000 2500 1940 1340 3000 3000 2990 2290 1720 1100

Stramit Monoclad®

0.42 4 2° 2700 2700 2370 ‒ ‒ ‒ 3000 3000 2660 2040 1640 1310 2910 2910 2600 2060 1690 1430

0.48 4 2° 2820 2820 2540 2250 ‒ ‒ 3000 3000 2920 2610 2250 1920 2910 2910 2670 2380 2070 1770


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 2460 2460 2050 1620 1240 ‒ 2340 2340 1850 1490 1040 ‒

0.48 3 5° 2160 2160 ‒ ‒ ‒ ‒ 2660 2660 2280 1780 1250 ‒ 2550 2550 2110 1610 1130 890

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEC


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 3000 3000 2230 ‒ 2800 2800 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2930 2930 2690 2240 3000 3000 2660 1940 1370 ‒ 2570 2570 2300 1840 1280 ‒

0.48 3 1° 2970 2970 2760 2370 3000 3000 2770 2060 1480 ‒ 2620 2620 2380 1980 1380 990

Stramit Longspan®

0.42 3 1.5° 2770 2770 2240 2800 2800 2100 1350 ‒ ‒ 2560 2560 1870 1000 ‒ ‒

0.48 3 1.5° 3000 3000 2610 3000 3000 2560 1970 1240 ‒ 3000 3000 2330 1740 1020 ‒

Stramit Monoclad®

0.42 4 2° 2400 2400 ‒ 2760 2760 2070 1650 1200 ‒ 2680 2680 2090 1690 1390 ‒

0.48 4 2° 2580 2580 2270 2960 2960 2630 2260 1860 1460 2700 2700 2410 2080 1710 1220


0.42 3 5° ‒ ‒ ‒ 2110 2110 1640 1240 ‒ ‒ 1930 1930 1520 1050 ‒ ‒

0.48 3 5° ‒ ‒ ‒ 2330 2330 1810 1260 ‒ ‒ 2170 2170 1650 1130 870 750

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEE


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 3910 3910 2760 ‒ ‒ 4040 4040 2450 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2880 2630 ‒ 3000 3000 2960 2530 1810 1360 2700 2700 2510 2230 1720 1290

0.48 3 1° 3000 3000 2930 2700 2240 3000 3000 3000 2690 1940 1490 2730 2730 2570 2310 1840 1390

Stramit Longspan®

0.42 3 1.5° 3000 3000 2650 2110 ‒ 3000 3000 2610 1960 1190 ‒ 3000 3000 2360 1710 ‒ ‒

0.48 3 1.5° 3000 3000 2930 2500 ‒ 3000 3000 3000 2390 1870 1230 3000 3000 2950 2210 1590 1010

Stramit Monoclad®

0.42 4 2° 2660 2660 2330 ‒ ‒ 3000 3000 2560 1980 1590 1210 2880 2880 2520 2000 1640 1390

0.48 4 2° 2780 2780 2500 2210 ‒ 3000 3000 2890 2560 2190 1860 2880 2880 2630 2340 2020 1720


0.42 3 5° ‒ ‒ ‒ ‒ ‒ 2410 2410 1970 1560 1160 ‒ 2290 2290 1780 1430 950 ‒

0.48 3 5° 2100 2100 ‒ ‒ ‒ 2620 2620 2210 1710 1180 ‒ 2510 2510 2040 1530 1090 870

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPED


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 2470 2470 ‒ 2030 2030 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2790 2790 2470 2810 2810 2170 1540 ‒ 2410 2410 2050 1430 ‒

0.48 3 1° 2850 2850 2560 2910 2910 2310 1650 ‒ 2470 2470 2160 1530 1070

Stramit Longspan®

0.42 3 1.5° 2440 2440 ‒ 2340 2340 1620 ‒ ‒ 2120 2120 1330 ‒ ‒

0.48 3 1.5° 2780 2780 2250 2930 2930 2140 1440 ‒ 2810 2640 1960 1180 ‒

Stramit Monoclad®

0.42 4 2° 2200 2200 ‒ 2290 2290 1760 1400 ‒ 2290 2290 1790 1460 ‒

0.48 4 2° 2370 2370 ‒ 2760 2760 2380 1980 1530 2520 2520 2190 1820 1280


0.42 3 5° ‒ ‒ ‒ 1760 1760 1390 ‒ ‒ 1650 1650 1240 ‒ ‒

0.48 3 5° ‒ ‒ ‒ 2010 2010 1460 ‒ ‒ 1830 1830 1250 930 770

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEF

These tables show maximum spans (mm) for patio applications with limiTed fooT Traffic load. These tables show maximum spans (mm) for patio applications with LIMITED FOOT TrAFFIC LOAD.

5


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 4040 4040 2890 2180 ‒ ‒ 4330 4330 2630 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2910 2670 2200 ‒ 3000 3000 3000 2630 1910 1470 2720 2720 2540 2270 1800 1360

0.48 3 1° 3000 3000 2950 2740 2340 ‒ 3000 3000 3000 2740 2030 1580 2750 2750 2600 2360 1950 1460

Stramit Longspan®

0.42 3 1.5° 3000 3000 2720 2200 ‒ ‒ 3000 3000 2690 2050 1330 ‒ 3000 3000 2460 1820 980 ‒

0.48 3 1.5° 3000 3000 2980 2580 ‒ ‒ 3000 3000 3000 2500 1940 1340 3000 3000 2990 2290 1720 1100

Stramit Monoclad®

0.42 4 2° 2700 2700 2370 ‒ ‒ ‒ 3000 3000 2660 2040 1640 1310 2910 2910 2600 2060 1690 1430

0.48 4 2° 2820 2820 2540 2250 ‒ ‒ 3000 3000 2920 2610 2250 1920 2910 2910 2670 2380 2070 1770


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 2460 2460 2050 1620 1240 ‒ 2340 2340 1850 1490 1040 ‒

0.48 3 5° 2160 2160 ‒ ‒ ‒ ‒ 2660 2660 2280 1780 1250 ‒ 2550 2550 2110 1610 1130 890

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEC


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 3000 3000 2230 ‒ 2800 2800 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2930 2930 2690 2240 3000 3000 2660 1940 1370 ‒ 2570 2570 2300 1840 1280 ‒

0.48 3 1° 2970 2970 2760 2370 3000 3000 2770 2060 1480 ‒ 2620 2620 2380 1980 1380 990

Stramit Longspan®

0.42 3 1.5° 2770 2770 2240 2800 2800 2100 1350 ‒ ‒ 2560 2560 1870 1000 ‒ ‒

0.48 3 1.5° 3000 3000 2610 3000 3000 2560 1970 1240 ‒ 3000 3000 2330 1740 1020 ‒

Stramit Monoclad®

0.42 4 2° 2400 2400 ‒ 2760 2760 2070 1650 1200 ‒ 2680 2680 2090 1690 1390 ‒

0.48 4 2° 2580 2580 2270 2960 2960 2630 2260 1860 1460 2700 2700 2410 2080 1710 1220


0.42 3 5° ‒ ‒ ‒ 2110 2110 1640 1240 ‒ ‒ 1930 1930 1520 1050 ‒ ‒

0.48 3 5° ‒ ‒ ‒ 2330 2330 1810 1260 ‒ ‒ 2170 2170 1650 1130 870 750

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEE


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 3910 3910 2760 ‒ ‒ 4040 4040 2450 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2880 2630 ‒ 3000 3000 2960 2530 1810 1360 2700 2700 2510 2230 1720 1290

0.48 3 1° 3000 3000 2930 2700 2240 3000 3000 3000 2690 1940 1490 2730 2730 2570 2310 1840 1390

Stramit Longspan®

0.42 3 1.5° 3000 3000 2650 2110 ‒ 3000 3000 2610 1960 1190 ‒ 3000 3000 2360 1710 ‒ ‒

0.48 3 1.5° 3000 3000 2930 2500 ‒ 3000 3000 3000 2390 1870 1230 3000 3000 2950 2210 1590 1010

Stramit Monoclad®

0.42 4 2° 2660 2660 2330 ‒ ‒ 3000 3000 2560 1980 1590 1210 2880 2880 2520 2000 1640 1390

0.48 4 2° 2780 2780 2500 2210 ‒ 3000 3000 2890 2560 2190 1860 2880 2880 2630 2340 2020 1720


0.42 3 5° ‒ ‒ ‒ ‒ ‒ 2410 2410 1970 1560 1160 ‒ 2290 2290 1780 1430 950 ‒

0.48 3 5° 2100 2100 ‒ ‒ ‒ 2620 2620 2210 1710 1180 ‒ 2510 2510 2040 1530 1090 870

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPED


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 2470 2470 ‒ 2030 2030 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2790 2790 2470 2810 2810 2170 1540 ‒ 2410 2410 2050 1430 ‒

0.48 3 1° 2850 2850 2560 2910 2910 2310 1650 ‒ 2470 2470 2160 1530 1070

Stramit Longspan®

0.42 3 1.5° 2440 2440 ‒ 2340 2340 1620 ‒ ‒ 2120 2120 1330 ‒ ‒

0.48 3 1.5° 2780 2780 2250 2930 2930 2140 1440 ‒ 2810 2640 1960 1180 ‒

Stramit Monoclad®

0.42 4 2° 2200 2200 ‒ 2290 2290 1760 1400 ‒ 2290 2290 1790 1460 ‒

0.48 4 2° 2370 2370 ‒ 2760 2760 2380 1980 1530 2520 2520 2190 1820 1280


0.42 3 5° ‒ ‒ ‒ 1760 1760 1390 ‒ ‒ 1650 1650 1240 ‒ ‒

0.48 3 5° ‒ ‒ ‒ 2010 2010 1460 ‒ ‒ 1830 1830 1250 930 770

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEF

These tables show maximum spans (mm) for patio applications with LIMITED FOOT TrAFFIC LOAD.

6


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 2220 2220 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2690 2690 2200 2660 2660 1910 1260 ‒ 2290 2290 1800 1230 ‒

0.48 3 1° 2760 2760 2340 2770 2770 2030 1450 ‒ 2370 2370 1950 1340 ‒

Stramit Longspan®

0.42 3 1.5° 2230 2230 ‒ 2090 2090 1290 ‒ ‒ 1860 1860 930 ‒ ‒

0.48 3 1.5° 2610 2610 2040 2630 2630 2230 1810 1240 2630 2370 1690 950 ‒

Stramit Monoclad®

0.42 4 2° ‒ ‒ ‒ 2070 2070 1630 1160 ‒ 2080 2080 1670 1360 ‒

0.48 4 2° 2270 2270 ‒ 2630 2630 2230 1810 1240 2400 2400 2060 1660 ‒


0.42 3 5° ‒ ‒ ‒ 1640 1640 1220 ‒ ‒ 1510 1510 1020 ‒ ‒

0.48 3 5° ‒ ‒ ‒ 1810 1810 1230 ‒ ‒ 1640 1640 1120 860 700

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEG


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 3640 3640 2600 ‒ ‒ ‒ 3650 3650 2210 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 3000 3000 2830 2560 ‒ ‒ 3000 3000 2880 2340 1690 1140 2670 2670 2450 2150 1580 1180

0.48 3 1° 3000 3000 2890 2640 ‒ ‒ 3000 3000 2970 2500 1790 1400 2710 2710 2520 2240 1700 1280

Stramit Longspan®

0.42 3 1.5° 2970 2970 2540 ‒ ‒ ‒ 3000 3000 2440 1800 ‒ ‒ 2980 2980 2240 1540 ‒ ‒

0.48 3 1.5° 3000 3000 2850 2380 ‒ ‒ 3000 3000 2990 2270 1700 1090 3000 3000 2730 2080 1410 ‒

Stramit Monoclad®

0.42 4 2° 2600 2600 2260 ‒ ‒ ‒ 3000 3000 2400 1870 1490 1110 3000 3000 2380 1910 1550 1330

0.48 4 2° 2720 2720 2430 2140 ‒ ‒ 3000 3000 2820 2470 2090 1760 2840 2840 2580 2270 1940 1600


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 2330 2330 1840 1480 ‒ ‒ 2200 2200 1720 1340 840 ‒

0.48 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 2550 2550 2100 1600 1120 ‒ 2430 2430 1930 1410 1030 840

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEJ


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 2180 2180 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2670 2670 2150 ‒ ‒ ‒ 2630 2630 1860 1190 ‒ ‒ 2270 2270 1760 1190 ‒ ‒

0.48 3 1° 2740 2740 2290 ‒ ‒ ‒ 2740 2740 1990 1420 ‒ ‒ 2360 2360 1900 1300 ‒ ‒

Stramit Longspan®

0.42 3 1.5° 2200 2200 ‒ ‒ ‒ ‒ 2050 2050 1230 ‒ ‒ ‒ 1820 1820 ‒ ‒ ‒ ‒

0.48 3 1.5° 2580 2580 ‒ ‒ ‒ ‒ 2760 2560 1910 1120 ‒ ‒ 2590 2330 1630 900 ‒ ‒

Stramit Monoclad®

0.42 4 2° ‒ ‒ ‒ ‒ ‒ ‒ 2040 2040 1600 1140 ‒ ‒ 2060 2060 1650 1340 ‒ ‒

0.48 4 2° 2250 2250 ‒ ‒ ‒ ‒ 2610 2610 2210 1780 1180 ‒ 2380 2380 2030 1630 ‒ ‒


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 1620 1620 1180 ‒ ‒ ‒ 1490 1490 970 ‒ ‒ ‒

0.48 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 1780 1780 1190 ‒ ‒ ‒ 1610 1610 1100 850 ‒ ‒

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEH


SINGLE DOUBLE EQUAL

WIND CLASSIFICATION


Stramit Sunset® 0.42 2 1° 2140 2140 ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒ ‒


0.42 3 1° 2650 2650 2100 ‒ ‒ ‒ 2600 2600 1820 1130 ‒ ‒ 2250 2250 1720 1170 ‒ ‒

0.48 3 1° 2720 2720 2250 ‒ ‒ ‒ 2720 2720 1950 1390 ‒ ‒ 2340 2340 1850 1270 ‒ ‒

Stramit Longspan®

0.42 3 1.5° 2160 2160 ‒ ‒ ‒ ‒ 2010 2010 1160 ‒ ‒ ‒ 1770 1770 ‒ ‒ ‒ ‒

0.48 3 1.5° 2540 2540 ‒ ‒ ‒ ‒ 2740 2510 1880 1080 ‒ ‒ 2540 2300 1560 ‒ ‒ ‒

Stramit Monoclad®

0.42 4 2° ‒ ‒ ‒ ‒ ‒ ‒ 2010 2010 1580 1110 ‒ ‒ 2030 2030 1630 1320 ‒ ‒

0.48 4 2° 2230 2230 ‒ ‒ ‒ ‒ 2580 2580 2180 1760 1090 ‒ 2360 2360 2010 1590 ‒ ‒


0.42 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 1590 1590 1150 ‒ ‒ ‒ 1460 1460 930 ‒ ‒ ‒

0.48 3 5° ‒ ‒ ‒ ‒ ‒ ‒ 1750 1750 1170 ‒ ‒ ‒ 1580 1580 1080 840 ‒ ‒

THIC

KN

ESS

BMT

(mm

)

FAST

ENER

S PE

R SH

EET

MIN

IMU

M S

LOPEK

These tables show maximum spans (mm) for patio applications with LIMITED FOOT TrAFFIC LOAD.

7

PricesPrices of Stramit® cladding and accessories can be obtained from your nearest Stramit location or distributor of Stramit® products. As Stramit does not provide an installation service, ask your tradesperson for a supply and fix price. Contact your nearest Stramit location for the names of tradespersons in your area.

LengthStramit® cladding is supplied cut-to-length. When designing or transporting long products ensure that the length is within the limit of the local transport authority regulations. The manufacturing tolerance on the length of product supplied is +0, -15mm.

OrderingStramit® cladding can be ordered directly, through distributors, or supplied and fixed by a roofing contractor.

Delivery/UnloadingDelivery can normally be made within 48 hours, subject to the delivery location, quantity and material availability, or can be at a pre-arranged date and time. Please ensure that suitable arrangements have been made for truck unloading, as this is the responsibility of the receiver. Pack mass may be up to one tonne. When lifting Stramit® cladding, care should be taken to ensure that the load is spread to prevent damage.

Handling/StorageStramit® cladding should be handled with care at all times to preserve the product capabilities and quality of the finish. Packs should always be kept dry and stored above ground level while on site. If the sheets become wet, they should be separated, wiped and placed in the open to promote drying.

Additional InformationAs well as our standard range of Technical Manuals, Installation Leaflets, Case Studies and other promotional literature, Stramit has a series of Guides to aid design. These include:

• Roof Slope Guide• Foot Traffic Guide• Concealed Fixed Decking• Bullnosing, Curving and Crimping• Acoustic Panels• Cyclonic Areas• Spring Curving Guide

Please contact your nearest Stramit location or visit www.stramit.com.au to download Stramit literature.

Other ProductsStramit offers a wide range of building products, including:

• Purlins and girts• Formwork decking• Roof and wall sheeting• Lightweight structural sections• Truss components• Gutters and downpipes• Fascia• Custom flashing• Insulating products• Fasteners

Procurement

For additional and comprehensive information on individual roofing products refer to Stramit’s technical literature, available from any Stramit Building Products branch or the Stramit website:

www.stramit.com.auFor fixing details such as fastener size, quantity and locations, refer to the Stramit® Product Technical Manuals and the Stramit Receiver Channel for Patio Roofing brochure, on the Stramit website.

8

The information in this brochure is, as far as possible, accurate at the date of publication.

Before application in a particular situation, Stramit recommends that appropriate

independent, qualified expert advice be obtained confirming the suitability of the product(s)

and information in question for the application proposed. While Stramit accepts its legal

obligations, be aware that to the extent permitted by law, Stramit disclaims all liability

(including liability for negligence) for all loss and damage resulting from the use of

information provided in this publication.

® Trade marks of Stramit Corporation Pty Limited ABN 57 005 010 195

Trading as Stramit Building Products. A member of the Fletcher Building Group.

© Stramit Corporation Pty Limited, June 2012

6632

New South WalesSydney (02) 9834 0900Queanbeyan (02) 6297 3533Orange (02) 6361 0444Albury (02) 6041 7600Newcastle (02) 4954 5033Coffs Harbour (02) 6652 6333Murwillumbah (02) 6672 8542

Northern TerritoryDarwin (08) 8947 0780

South AustraliaAdelaide (08) 8262 4444

Western AustraliaPerth (08) 9493 8800

QueenslandBrisbane (07) 3803 9999Sunshine Coast (07) 5456 4083Maryborough (07) 4121 2433Rockhampton (07) 4936 2577Mackay (07) 4942 3488Townsville (07) 4779 0844Cairns (07) 4045 3069

VictoriaMelbourne (03) 9237 6300Bendigo (03) 5448 6400Mildura (03) 5018 4800

TasmaniaHobart (03) 6263 5536

www.stramit.com.au

Stramit Patio Roofing Spans Tablefor pitched roof. • The number of supports (beams or purlins)...

Documents

Transcript of Stramit Patio Roofing Spans Tablefor pitched roof. • The number of supports (beams or purlins)...