STEPOSOL MET - Stepan Company · Wipe Away Paint and Permanent Ink! (BCI)= 75* STEPOSOL® MET-10...
Transcript of STEPOSOL MET - Stepan Company · Wipe Away Paint and Permanent Ink! (BCI)= 75* STEPOSOL® MET-10...
Innovative Chemical Solutions for a Cleaner, Healthier, More Energy Efficient World
A D VA N TA G E SA D VA N TA G E SA D VA N TA G E S
STEPOSOLSTEPOSOLSTEPOSOL®®® METMETMET---10U10U10U
A Q U E O U S L A T E X B R U S H C L E A N E R
5 % S T E P O S O L ® M E T - 1 0 U v s . 1 0 0 % M i n e r a l S p i r i t s
Ingredient % by Weight
MEA (Monoethanolamine) 5.0
BIO-SOFT® N91-6 (Alcohol Ethoxylate, 6 moles EO)
10.0
STEPOSOL® MET-10U 5.0
Deionized Water 80.0
5% of STEPOSOL® MET-10U, in this aqueous chassis,
removes almost all of the dried latex paint, restoring the
paint brush to near original conditions. Mineral Spirits
has minimal effect on removing the dried latex paint.
CHASSIS
Unused Dried Latex
Paint Unused
STEPOSOL® MET-10U
Professional latex paint brush with white latex paint dried overnight. Placed brush into container with product for two hours. Gently shook
brush in solution and removed. Wiped with cloth or paper towel, then rinsed with water and wiped dry.
Mineral Sprits
STEPOSOL® MET-10U
P R O P E R T I E SP R O P E R T I E SP R O P E R T I E S
EFFECTIVE LATEX REMOVER IN DILUTED AQUEOUS SOLUTIONS
EXCELLENT SYNERGY WITH MONOETHANOLAMINE (MEA)
EXCELLENT SOLUBILITY IN ORGANIC SOLVENTS
STABLE OVER WIDE pH RANGE (pH 3-12)
KAURI-BUTANOL VALUE: >1000
pH, (5% in1:1 IPA/H 2O): 8.0
VAPOR PRESSURE, 20 °C: 0 .0025 mm Hg
BOILING POINT: 297 °C (566 °F)
FLASH POINT, PMCC: 134 °C (273 °F)
COLOR GARDNER: 1 MAX.
S u r f a c t a n t S o l u t i o n t o S o l v e n t R e p l a c e m e n tT M
.
R e p l a c e M e t h y l e n e C h l o r i d e , M i n e r a l S p i r i t s , a n d N M P .
W i p e A w a y P a i n t a n d P e r m a n e n t I n k !
STEPOSOL® MET-10 utilizes the cleaning properties of a surfactant to outperform
many solvents commonly used in paint and coatings removal/stripping. It fulfills the role
of both a low HLB surfactant and a powerful solvent, which allows it to be highly
effective against a broad range of soils. STEPOSOL® MET-10U can be used in
formulations ranging from pH 3–12 while achieving viscosities from water-thin to gel.
This metathesis-derived, nonionic surfactant is an unsaturated, short chain amide
resulting from Stepan’s collaboration with Elevance Renewable Sciences and furthers
Stepan’s effort to deliver renewable, naturally-derived products to the market.
With a Kauri-Butanol value greater than 1000, STEPOSOL® MET-10U provides superior cleaning performance and is
environmentally friendly due to a low vapor pressure, high boiling point, and Biorenewable Carbon Index (BCI) of 75%.
BIORENEWABLE CARBON INDEX
(BCI)= 75*
LOW VAPOR PRESSURE -VOC (LVP-VOC)*
NON -FLAMMABLE
*For additional information, please contact Stepan U.S. Technical Service at [email protected] or (800) 745-7837 and visit www.stepan.com/STEPOSOLMET.
PAINT & COATINGS
REMOVAL/
STRIPPING
A Q U E O U S P E R M A N E N T M A R K E R R E M O V A L
1 % S T E P O S O L ® M E T - 1 0 U v s . C o m m e r c i a l P r o d u c t s
P R O P E R T I E S
2014 © Stepan Company. All rights reserved. Disclaimer: Nothing contained herein grants or extends a license, expressed or implied, in connection with patents, issued or pending, of the manufacturer or others. The information contained herein is based on the manufacturer’s own study and the work of others. The manufacturer makes no warranties, expressed or implied, as to the accuracy, completeness, or adequacy of the information contained herein. THE MANUFACTURER SHALL NOT BE LIABLE (REGARDLESS OF FAULT) TO THE VENDEE’S EMPLOYEES, OR ANYONE FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE ACCURACY, COMPLETENESS ADEQUACY OR FURNISHING OF SUCH INFORMATION.
BIO-SOFT®, STEPANATE®, and STEPOSOL® are registered trademarks of Stepan Company. Version: 9/2014
A Q U E O U S G R A F F I T I R E M O V A L O N E N A M E L
5 % S T E P O S O L ® M E T - 1 0 U v s . C o m m e r c i a l G r a f f i t i R e m o v e r ( A c e t o n e a n d N M P ) Before After
Commercial Graffiti Remover STEPOSOL® MET-10U Chassis
Before Sprayed with Products After 1 Min
White Dry-Erase Board (10” x 12”). Marked 3 regions with the word “Test” using a premium black permanent marker.
Sprayed a region with each product 3 times to cover each word. Waited 1 minute, then wiped with paper towel.
After Wiping
Ingredient % by Weight
D-Limonene 0.5
STEPOSOL® MET-10U 1.0
Balance: Emulsifier and Water
Mildly Alkaline
CHASSIS STEPOSOL® MET-10U chassis (right) completely removes the premium
permanent marker without damaging the board, outperforming a leading glass
cleaner (left) and a premium white board marker remover (middle).
The STEPOSOL® MET-10U chassis is over 95% water, containing only 1%
STEPOSOL® MET-10U.
White baked enamel sign panel (7” x 10”) with premium enamel, black, flat spray paint. Sprayed graffiti (paint) across panel, dried overnight.
Commercial remover, containing acetone and NMP, sprayed on the left half and STEPOSOL® MET-10U chassis on the right half with 15 minutes contact time and then wiped with a damp scrub sponge.
See page 1 for STEPOSOL® MET-10U chassis.
5% STEPOSOL® MET-10U, in this aqueous chassis, provides equivalent
cleaning performance to the commercial remover containing acetone and
NMP. STEPOSOL® MET-10U breaks the paint into particles, allowing for
easy clean-up, while the commercial remover dissolves the paint.
100% Solvent 80% Water
A Q U E O U S G R A F F I T I R E M O V A L O N C O N C R E T E
5 % S T E P O S O L ® M E T - 1 0 U v s . C o m m e r c i a l G r a f f i t i R e m o v e r ( A c e t o n e a n d N M P )
Sprayed with Product After Scrub, Rinse, Dry
STEPOSOL® MET-10U Chassis
80% Water
Commercial Graffiti Remover
100% Solvent
Before
Commercial Graffiti Remover
100% Solvent
STEPOSOL® MET-10U Chassis
80% Water
5% STEPOSOL® MET-10U, in this aqueous chassis, provides equivalent
cleaning performance to the commercial remover containing acetone and
NMP. The STEPOSOL® MET-10U chassis easily rinses with water
compared to a 100% solvent product.
Concrete block with premium enamel, black, flat spray paint. Sprayed graffiti (paint) in two zones on the concrete block, cured in 50 °C oven
for 1 hour. Commercial remover, containing acetone and NMP, sprayed on the left half and STEPOSOL® MET-10U solution on the right half with 15 minutes contact time and scrubbed with a plastic
bristle brush, then rinsed and dried.
See page 1 for STEPOSOL® MET-10U chassis.
Patent Pending