1

MODULE – 5

ALLOY & SPECIAL STEELS

Rahul Kumar KIIT UNIVERSITY

2

General Categories of Alloy Steels

Carbon and Alloy Steels

Stainless Steel

Tool and Die Steels

Cast Steels (Crucible Steels)

3

Effects of Alloying Elements in Steels

•Boron: improves hardenability without the loss of (or even with some

improvement in) machinability and formability

•Calcium: deoxidizes steels, improves toughness and improve formability

and machinability

•Carbon: improves hardenability, strength, hardness and wear resistance,

as well as reduces ductility, weldability and toughness

•Cerium: controls shape of inclusions and improves toughness in high-

strength low alloy steels, as well as deoxidizes steels

4

• Chromium: improves toughness, hardenability, wear and corrosion

resistance and high-temperature strength. It also increases depth of

hardness penetration resulting from heat treatment by promoting

carburization

• Cobalt: improves strength and hardness at elevated temperatures

• Copper: improves resistance to atmospheric corrosion and to lesser

extent increases strength with little loss in ductility, as well as also

adversely affects hot-working characteristics and surface quality

• Lead: improves machinability, as well as causes liquid-metal

embrittlement

5

• Magnesium: has the same effects as cerium

• Manganese: improves hardenability, strength, abrasion resistance and

machinability, as well as deoxidizes molten steel, reduce shot shortness,

and decreases weldability

• Molybdenum: improves hardenability, wear resistance, toughness,

elevated-temperature strength, creep resistance and hardness, as well

as minimizes temper embrittlement

• Nickel: improves strength, toughness and corrosion resistance, as well

as improves hardenability

• Niobium (columbium): imparts fineness of grain size and improves

strength and impact toughness, as well as lowers transition temperature

and decrease hardenability

6

• Phosphorus: improves strength, hardenability, corrosion resistance

and machinability, as well as severely reduces ductility and toughness

• Selenium: improves machinability

• Silicon: improves strength, hardness, corrosion resistance, and

electrical conductivity; it decreases magnetic-hysteresis loss,

machinability and cold formability

• Sulfur: improves machinability when combined with manganese, as

well as lowers impact strength and ductility and impairs surface

quality and weldability

7

• Tantalum: has effects similar to those of niobium

• Tellurium: improves machinability, formability and toughness

• Titanium: improves hardenability; it deoxidizes steels

• Tungsten: has the same effects as cobalt

• Vanadium: improves strength, toughness, abrasion resistance and

hardness at elevated temperatures, as well as inhibits grain growth

during heat treatment

• Zirconium: has same effects as cerium

8

1. Carbon and Alloy Steels

•carbon and alloying steels are the most commonly used metals

•structural makeup and controlled processing of these steels make them suitable for many different functions

•basic product shapes include plate, sheet, bar, wire, tube, castings, and forgings

•increasing % of alloying elements in steels, increases properties they impart (different elements are added to give different properties

•elements pass on properties such as hardenability, strength, hardness, toughness, wear resistance, etc

•some properties are beneficial while others are detrimental

9

Carbon Steels

•also known as plain carbon steels

•group by % of carbon content (weight basis)

•higher the carbon content greater the hardness, strength and wear

resistance after heat treatment

•soft, tough, easily machined, welded & case hardened

•designation: e.g. 1040 steel - 0.40 wt % C

•types:Low-carbon steel (mild steels)

Medium-carbon steel

High-carbon steel

10

Low-carbon steel (mild steels)

•has less than 0.30 % carbon

•used in everyday industrial products like bolts, nuts, sheet, plate and tubes

Medium-carbon steel

•has 0.30% to 0.60 % carbon

•used for jobs requiring higher strength such as machinery, automotive equipment parts, and metalworking equipment

High-carbon steel

•has more than 0.60 % carbon

•used parts that require the highest strength, hardness and wear resistance

•once manufactured they are heat treated and tempered

11

High carbon steel nails

Low carbon steel wires

Medium carbon steel nuts

12

Alloy Steels

•contain significant amounts of alloying elements

•expensive

Types of Alloy Steels

• High strength low alloy steels (HSLA)

• Microalloyed steels

• Nanoalloyed steels

• Bearing steels

• Cold forming steels

• Chained steels

13

High-Strength, Low-Alloy Steels (HSLA Steels)

•developed to improve the ratio of strength to weight

•commonly used in automobile bodies and in transportation industry (reduced weight makes for better fuel economy)

Microalloyed Steels•provide superior properties without the use of heat treating

•when cooled carefully these steels develop enhanced and consistent strength

Nanoalloyed Steels•have extremely small grain size (10-100 nm)

•Since their synthesis is done at atomic level their properties can be controlled specifically

14

15

High strength low alloy steel sheets

Microalloyed steel connecting rods

Nanoalloyed steel bicycle hub

16

Bearing steel pipes

Cold forming steel front

Chained steel chain

17

2. Stainless Steels

•primarily know for their corrosion resistance, high strength, and

ductility and chromium content

•reason for name stainless is due to the fact that in presence of oxygen,

steel develops a thin, hard, adherent film of chromium

•Even if surface is scratched, protective film is rebuilt through

passivation

•for passivation to occur, there needs to be minimum chromium content

of 10 to 12 % by weight

18

• tend to have lower carbon content since increased carbon content

lowers the corrosion resistance of stainless steels

• since carbon reacts with chromium, it decreases the available

chromium content which is needed for developing protective film

• using stainless steel as reinforcing bars, has become a new trend in

concrete structures such as highways buildings and bridges

• more beneficial than carbon steels because it is resistant to

corrosion from road salts and the concrete itself

19

Applications Products of Stainless Steels

20

3. Tool and Die Steels

•generally alloyed steels

•medium to high carbon

•up to 25% total alloying elements

•design for high strength, impact toughness and wear resistance at normal and elevated temperatures

•used at temperatures up to 600°C

•specialty steels – very expensive

•quench and tempered

•very clean steels

•applications like dies, drills, cutting blades, hot working dies, etc

21

Desirable Properties of Tool Steels

•Hardness - Resistance to Deforming & Flattening

•Toughness - Resistance to Breakage & Chipping

•Wear - Resistance to Abrasion & Erosion

•Corrosion - Resistance to Rusting and Pitting

22

Alloying Elements in Tool Steels & their Effects

Carbon (C) +Strength, +Hardenability, -Toughness

Chromium (Cr) +Strength, +Hardenability, +Corrosion Resistance - Toughness

Molybdenum (Mo) +Strength, +Hardenability, +Toughness, +Hot Hardness

Vanadium (V) +Hardenability, +Toughness, +Hot Hardness, +Wear

Tungsten (W) +Strength, +Hardenability, +Hot Hardness, -Toughness

Cobalt (Co) +Hot Hardness, +Wear, -Toughness

Manganese (Mn) +Strength, +Hardenability, +Toughness

Nickel (Ni) +Hardenability, +Toughness, +Corrosion Resistance

+ increases- decreases

23

Classification of Tool Steels

Tool Steel Class of Alloys Examples (industrial names)Cold Work W (water hardening)

O (oil hardening)A (air hardening)D (high C & Cr)

W1, W2, W5O1, O2, O6, O7A2, A4, A6, A7, A8, A9, A10, A11D2, D3, D4, D5, D7

Shock Resisting

S S1, S2, S4, S5, S6, S7

Hot Work H Chromium types: H10-H19 Tungsten types: H20-H39 Molybdenum types: H40-H59

High Speed MT

Molybdenum types: M1, M2, M3-1, M3-2, M4, M6, M7, M10, M33, M34, M36, M41Tungsten types: T1, T4, T5, T6, T8, T15

Mold P P6, P20, P21

24

Classification of Tool Steels

25

Cold Work Tool Steels

•used at low temperature-sharpness

•include all W, O, A & D class of alloys

•typical applications include cold working operations such as stamping

dies, draw dies, burnishing tools, coining tools and shear blades

26

Shock Resisting Tool Steels

•used at low temperature-toughness & impact toughness

•include all S class alloys

•toughest tool steels

•typically applications include screw driver blades, shear blades, chisels,

knockout pins, punches, and riveting tools

27

Hot Work Tool Steels

•used at high temperature-toughness, high resistance to wear & cracking

•include all H class alloys

•typical applications include dies for forging, die casting, heading,

piercing, trimming, extrusion and hot-shear and punching blades

28

High Speed Tool Steels

•used at high temperature-sharpness

•Include M1 to M52, T1 to T15 class of alloys

•can be hardened to 62-67 RC and can maintain it in service temperatures

as high as 540°C, making them very useful in high-speed machinery

•typical applications include end mills, drills, lathe tools, planar tools,

punches, reamers, routers, taps, saws, broaches, chasers and hobs

29

4. Cast Steels (Crucible Steels)• term originally applied to crucible steel (sometimes used to describe

tool steels, which is misleading)

• fine variety of steel, originally made by smelting blister or cementation steel & pouring molten steel into moulds

• manufacture is essentially a refining process, which is dependent on pre-existing furnace products

• cannot not subjected to further forging or rolling