Steam Turbine - biomass
-
Upload
olivier-de-block -
Category
Documents
-
view
30 -
download
1
Transcript of Steam Turbine - biomass
![Page 1: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/1.jpg)
www.siemens.com / energy
Turbines for Biomass PlantsProducts for Biomass-fired Power Generation and District Heating & Cooling Applications
Industrial Power
![Page 2: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/2.jpg)
Feindaten fehlen
![Page 3: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/3.jpg)
3
Biomass to Fuel the Future
Today we see many compelling environmental and economic reasons to use biomass as a power generation fuel.
Combusting biomass feedstock to create electricity does not contribute to global warming and helps avoid the release of other harmful emissions. Also, viable fuels are produced in many industries with no additional process- ing costs involved, further strengthening the financial feasibility of new plants on favorable sites. Additionally, many countries have established subsidies to make bio- mass based power generation economically viable. The possibility of firing a biomass plant on diverse feedstocks is an additional support for project economics and ensures security of fuel supply. As we are striving to move to a low-carbon economy, biomass energy for both industry and electricity generators will become an increasingly important – and sustainable – source of baseload power.
Although most biomass generation uses well-known technology, many breakthroughs in both the energy transfer and delivery of feedstock are on the horizon. Coupled with new climate regulations and increasing fossil fuel prices, industry and electricity generators are increasingly seeking the benefits of building new biomass capacity. Engaging experienced equipment manufacturers is an important step toward commissioning a new bio- mass plant. Over the long term, having a partner with an installed biomass base of over 3.5 GW can only improve the success of your biomass development strategy.
Biomass Combustion Technology
The two most common technologies used to combust biomass are stoker boilers and fluidized bed combustion boilers. Depending on how the biomass is pre-treated before combustion, one or another type of boiler may be more appropriate to ensure consistent steam parameters, the most efficient use of factory inputs, and environ- mental compliance.
Typical biomass fuels include a wide variety of material. Some common fuels are forestry by-products, agricul- tural wastes, municipal wastes, landfill gas, and syngas. There are also many next-generation biomass feedstocks in different stages of commercialization. These new fuels have the potential to dramatically scale plant sizes and t he feedstock supply chain, creating significant opportunities for additional generation fleet expansion.
Feedstock characteristics are also used to determine which type of boiler is the most appropriate for a biomass plant. While stokers and fluidized bed boilers can be used for similar applications across industries, recovery boilers are used to both generate steam and to recycle chemical factory inputs, especially in forest products industries, the pulp and paper industry uses special recovery boilers to combust the organic residues resulting from the process of wood pulping, and to both generate process steam and electricity.
Whichever combustion technology is used in your biomass plant, a Siemens steam turbine will ensure high plant performance. These flexible machines can even optimize electric output in plants which have steam parameters affected by inconsistent feedstock moisture content. This is possible by integrating industry-leading steam cycle technology.
![Page 4: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/4.jpg)
4
Steam Turbines for Biomass Plants
Whereas in Europe, due to subsidiary regulations, typically steam turbines up to 40 MW are used, other regions prefer a power output up to 120 MW. The Siemens industrial steam turbine portfolio can be used with any biomass boiler to generate power from 75 kW up to more than 250 MW. The Siemens experts will assist in selecting the optimum turbine that meets all appplication requirements while at the same time it minimizes the investment cost.
The Siemens steam turbine portfolio is characterized by efficiency and durability. Turbine generator sets have been deployed in almost 100 biomass-fueled plants in the past decade with an outstanding record of applicability and reliability.
Siemens can also supply your steam turbine with auxiliary equipment such as generator, a condenser system, monitoring and control systems and power transmission equipment.
Tailored Turbines & Leading Technology
Siemens turbines are available for back-pressure or con-densing operations in a single or multi-stage design. They can also be equipped with single or multiple controlled and uncontrolled extractions (bleeds) to satisfy particular process or district heating as well as cooling requirements. Additionally, Siemens offers turbine-generator packages with a reheat feature, further optimizing plant perfor-mance and efficiency.
Turbines with reheat can improve overall plant efficiency by up to 3%, further mitigating the release of harmful emissions by burning less fuel. Each turbine, along with its customized features, is built to meet specific demands.
Stevens Croft Lockerbie, Scotland
As one of the UK’s largest biomass-fueled power stations, Stevens Croft powers 70,000 homes while displacing 140,000 tons of C02 per year. It also sustains up to 300 jobs in the regional economy. Stevens Croft is considered a milestone in biomass power plant development and has acted as an example of system efficiency.
Steam turbine: SST-800
Power output: 50.3 MW
Inlet pressure: 137 bar / 1,987 psi
Inlet temperature: 535 °C / 995 °F
Fuel: Green & waste wood
![Page 5: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/5.jpg)
5
Integrating a steam reheat system into a biomass plant is one of the best ways to increase overall plant performance. With the Siemens reheat turbine package, live steam is run through a high pressure (HP) turbine, sent back to the steam generator to increase steam temperature, then run through a low pressure (LP) turbine. Raising the temperature of steam that is going from a high to a low pressure turbine allows for greater output using the same amount of fuel. Geared single-casing reheat solutions up to 60 MW are also available in the Siemens portfolio.
Reheat Improves Efficiency
Steam turbine generating setHP steamSteam generator
Reheat steam
Super-heater
Reheater
Evaporator
Deaerator
Feedwater
Pump
Low pressure preheater
Pump
Water or air cooled condenser
Increasing Cycle Efficiency with Reheat
![Page 6: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/6.jpg)
6
Combined Heat and Power
Combined heat and power generation, also known as cogeneration, is used for many different purposes. Harnessing heat created by power generation increases plant outputs, reduces fuel consumption, and creates another valuable commodity which can improve plant economics. Whatever the application of a cogeneration system might be, efficient conversion of waste heat into a commercial resource is a critical necessity. All Siemens turbines can employ extractions, bleeds, and other features to meet the customer specifications.
CO2 and Emissions Reduction
Biomass generation is known to be a carbon-neutral power source and is being adopted as an important alternative to fossil fuel baseload generation. Using a highly efficient Siemens turbine can create additional long-term environmental advantages for industries and electricity generators seeking to further decrease their carbon and emissions footprints. Less fuel consumption over a plant‘s lifetime due to industry-leading efficiency results in significant cost savings and fewer system pollutants, compared to less efficient machines. This is especially true if the biomass system incorporates a Siemens reheat steam turbine or is deployed in a Combined Heat and Power (CHP) application.
Environmental Benefits
![Page 7: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/7.jpg)
7
![Page 8: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/8.jpg)
8
Biomass plants at Industrial Facilities
Siemens has a comprehensive range of experience in creating solutions for biomass industrial power applications. Siemens steam turbines can be found in facilities on every continent and across industrial sectors. Our engineering and sales teams are expert at optimizing turbine packages for highly specific and complex processes.
Biomass is a common on-site energy source for industries which produce a usable feedstock as waste during factory operations. Installing a biomass power plant to burn this waste is the best solution for closing the factory input cycle while cutting energy costs and maintaining high power availability. Waste biomass is an efficient fuel and is usually characterized by naturally low emissions. Using a highly efficient turbine may also result in increased operational savings as punitive environmental and green- house gas policies become more prevalent at both the national and international levels.
Wisaforest Pulp and Paper Mill Pietarsaari, Finland
The Wisaforest Mill’s biomass generator is one of the largest 100% biomass-fired power plant in the world. In addition to supplying electricity and process steam to the mill’s operations, it also provides district heating to the surrounding town of Pietarsaari.
Steam turbine: SST-800
Power output: 143 MW
Inlet pressure: 100 bar / 1,450 psi
Inlet temperature: 505 °C / 941 °F
Fuel: Pulp and paper mill by-products
Sierra Pacific Industries Aberdeen, Washington, USA
This 18 MW unit was installed and commissioned in 2002 at a Sierra Pacific Industries lumber mill. The cogeneration unit generates power and provides steam to several kilns with various loads depending on ambient conditions, the time of year, and lumber quality. The biomass boiler burns sawdust from lumber mill operations and additional fuels from the forest and land nearby.
Steam turbine: SST-300
Power output: up to 18 MW
Inlet pressure: 85.5 bar / 1,240 psi
Inlet temperature: 482 °C / 900 °F
Fuel: Forest industry by-products
![Page 9: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/9.jpg)
9
Dedicated Biomass Power Stations
The location of a biomass plant used for electricity produc-tion is usually dependent on the regional availability of feedstock. The size of dedicated biomass power stations is also often driven by local biomass availability. Transport costs of the usually bulky fuel play a major role in the plant’s economics. Rail and especially water shipping has reduced transport costs significantly, which has led to the development of a global biomass market. As the market for commoditized biomass fuels expands, so will the expan-sion of centralized biomass electricity production fleets.
Because of decades of experience supplying, building, and servicing equipment in biomass plants, Siemens steam turbines and turbosets are exceptionally well-suited for pure power generation. With high efficien-cies and minimal outages, Siemens machines maxi-mize electric MWh generated. With a leading efficiency profile, a Siemens turbine further reduces a plant’s life-time emissions footprint while delivering superior effi-ciency gains. These advantages and more positively impact plant financeability.
Biomass Power Plant Simmering Vienna, Austria
The Simmering biomass power plant, owned by the Viennese utility Wien Energie, is exclusively fed with fresh wood from the forest. Producing 23.4 MWe electricity in summer and 15.06 MWe plus 37 MWth for district heating in winter, the plant reduces Vienna’s CO2 emissions by 144,000 tons per annum. In operation with heat extraction, total efficiency is 83%.
Steam turbine: SST-400, Reheat
Power output: 23.4 MW
Inlet pressure: 120 bar / 1,740 psi
Inlet temperature: 520 °C / 968 °F
Fuel: Fresh wood
Afval Energie Bedrijf Amsterdam, Netherlands
Afval Energie Bedrijf (AEB; Waste and Energy Company Amsterdam) burns 1.7 million tonnes of waste per year and has recently increased its energy generation efficiency from 22% to 30%. This 8% increase resulted from installing a new SST-700 with a steam reheat system. AEB not only generates power from Amsterdam’s municipal waste, but also recovers and sells materials from the waste stream such as metals and gypsum.
Steam turbine: SST-700, Reheat
Power output: 74 MW
Inlet pressure: 125 bar / 1,813 psi
Inlet temperature: 440 °C / 824 °F
Fuel: Municipal solid waste
![Page 10: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/10.jpg)
10
District Heating and Cooling
District heating and cooling using a cogeneration system is one of the most efficient applications of a biomass plant. Usually a plant generates thermal energy at a centralized location and distributes steam to a larger number of buildings for space and water heating. District heating plants can provide higher efficiencies and better pollution control than stand-alone solutions. The process is normally governed by the total heat load and electrical energy is supplied as an additional benefit.
Whether a cogeneration application is for a district energy system, a heating or cooling system, or any other application, Siemens expertise ensures that your project will maintain optimal performance in markets with demand fluctuation. Any Siemens steam turbine can also feature extraction customization as required. The Siemens engineering staff is expert at designing turbines which can maximize output and plant value for seasonal load and demand variations.
Biomass District Heating Plant Igelsta Södertälje, Sweden
Sweden’s largest biomass plant Igelsta is situated in Södertälje, west of Stockholm. Inaugurated in March 2010, it uses a biomass fuel mix consisting of about 90% renewable fuels like forest refuse, wood chips, tree bark, and 10% non-recyclable waste paper and plastic. It produces 200 MW heat and 85 MW electricity, the equivalent of heating 50,000 households and generating electricity for 100,000 residences.
Steam turbine: SST-800
Power output: 90 MW
Inlet pressure: 85 bar / 1,305 psi
Inlet temperature: 540 °C / 1,004 °F
Fuel: Biomass mix
Biomass Power Plant Eccleshall, UK
The Eccleshall power plant was commissioned in September 2007 and has 13 MW of thermal and 2.65 MW of electrical capacity. The fuels burned range from woodchips, compost oversize, straw to miscanthus. The plant generates enough electricity to power 2,600 homes, equivalent to the local town of Eccleshall, making it one of the first carbon-neutral towns in the UK.
Steam turbine: SST-110
Power output: 2.6 MW
Inlet pressure: 41 bar / 595 psi
Inlet temperature: 450 °C / 842 °F
Fuel: Biomass mix
![Page 11: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/11.jpg)
11
Gas Turbines for Biomass Plants
Digester Systems
Digester systems are used mostly at facilities which have access to large amounts of feedstock that emits methane as part of its decomposition. One unique feature of this type of gaseous biomass is that it can be used both for steam-generation and as a fuel for gas turbines. This flexibility makes building digester systems very attractive for many food and beverage, agricultural, and municipal solid waste process facilities.
Landfill Gas-Fueled Gas Turbines
Landfill gas-fueled gas turbines are usually located at existing landfills or in close proximity to facilities which process waste. At existing landfills, naturally occuring methane is collected through a piping system, cleaned, and then routed to a combustion turbine to generate power. Because society will always generate waste, landfill gas is considered a renewable energy source and is often eligible for government incentive programs.
Siemens flexible gas and steam turbines can be used to add value to both landfill gas and digestable feedstock assets. A Siemens gas turbine can use biomass-derived fuels to create power at maximum efficiencies. All gas turbines can come equipped with a dry-low emission combustion system which operates in a wide variety of load ranges and fuels.
Experience in landfill gas and digestion-based power generation using both gas and steam turbines, individually or as a combined cycle, makes Siemens an ideal partner for this unique technology. For more information on Siemens gas turbines, please visit our website www.siemens.com/energy/gasturbines.
UNH Cogeneration Plant Durham, New Hampshire, USA
Rewrite as The University of Hampshire (UNH) cogeneration plant, fired on landfill gas, supplies 85% of the heat and 75% of the power demand of UNH Durham. By utilizing a Siemens gas turbine with a Heat Recovery Steam Generator (HRSG), UNH Durham was able to cut their greenhouse gas emissions by 40%. UNH Cogen was recognized by the US Environmental Protection Agency (EPA) as a “Project of the Year 2010” at their Landfill Methane Outreach Program annual conference.
Gas turbine: SGT-300
Power output: 7.9 MW
Combustion system: Dual-fuel Dry-Low Emissions (DLE)
Fuel: Landfill gas, natural gas, distillate fuel
![Page 12: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/12.jpg)
12
Process Control in Biomass Plants
The economic viability of biomass plants depends on the degree of process efficiency in biofuels production as well as biomass for biochemical products and heat and power generation. For economic, safe and sustainable operation in biomass plants we offer the right products, solutions and services for the integration of automation and electrical infrastructure.
With Totally Integrated Automation (TIA) and Totally Integrated Power (TIP) Siemens is the only provider of a comprehensive range of products and systems for the automation and the energy management of biomass plants.
Numerous aspects have to be considered for the planning and implementation of automation, control, drive, instrumentation and electrical system components for biomass plants. The requirements depend on the plant type and size, the used feedstock, the production process itself and the further processing, e.g. raw biogas mostly used for combustion in combined heat and power plants. Also local requirements in terms of layout and design as well as compliance with governmental regulations are important.
The use of TIA and TIP provides the full range of control and diagnostic options from the field level to the production control level up to the management level because all field devices, automation and drive components are monitored. Mechanical components such as motors, pumps, valves, or heat exchangers are also supervised. Plant monitoring can be performed locally, decentralized, or via remote services - various options for increasing productivity and reducing TCO considerably.
Modular DCS, SCADA, and MES solutions are part of our offer with different graphical configuration tools – either integrated directly in SIMATIC PCS 7 or using WinCC flexible. This enables the efficient parameterisation of field devices and set-up of electrical components. The benefits of an automation and visualization system are to handle the measurements and clearly visualize these process values. That includes messages, alarms, trend analyses and reports for preventive or condition-based maintenance as well as the integration of third party equipment and package units such as compressors, gasifiers, safety and energy management concepts.
Agratec Biogas Power Plant Jessen, Germany
One of the largest biogas plants in Europe has been installed in Jessen, Germany, by Agratec AG. In four CHP plants, the company produces power and heat to support 12,500 households with energy.
Feedstock: whole plant silage, corn silage, grass silage, cereals
Process: Dry fermentation, post digestion, gas processing and desulfuration
Products: Power and heat as well as organic solid and liquid fertilizer as a by-product
Energy: 5.3 MW of power and 5.1 MW of heat will be generated in four CHP plants
![Page 13: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/13.jpg)
13
Siemens offers a broad portfolio of medium- and low-voltage components including power monitoring. Connecting them to the process control system, the world’s largest installed fieldbus PROFIBUS, provides universal integration in the electrical infrastructure and in communications.
Central engineering, operation and monitoring of field technology, of smart motor-control centers, drives and switchgears with one system facilitates power measuring and provides transparancy for production and electrical processes thanks to an integrated view.
In combination with the integrated plant asset management functionalities and energy management it helps to improve plant availability and to reduce energy consumption.
The best way to ensure highest plant availability and efficiency is to keep track of all relevant processes at all times and to manage the plant as a whole. To ensure just this, we provide so-called MAV concepts over the entire lifecycle as well as efficient and user-friendly systems for plant operation and monitoring.
![Page 14: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/14.jpg)
14
Inbicon Biomass Refinery Kalundborg, Denmark
The Danish company Inbicon A/S designed its refinery in Kalundborg, Denmark, as one of the first “second generation” biofuels plants to turn straw into bioethanol and pellets. The plant is fully integrated, designed for commercial production with automatic operation 24/7 and a limited staff.
Feedstock: 33.000 tons of straw p.a.
Process: Fermentation and distillation
Products: Per year, 5,300 tons of fuel, 12,100 tons of cattle feed from the C5 molasses and 14,300 tons of pellets from the lignin
Energy: Energy integration with a power plant, energy surplus brings down the cost for both plants
Siemens Solution: Power distribution, control systems and process instruments
Siemens Components for Biomass Power Plants
![Page 15: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/15.jpg)
15
Power Output (MW )
65
50
10
20
7
12
8.5
6
0.75
0.3
SST-900
SST-800*
SST-700*
SST-600*
SST-500
SST-400*
SST-300*
SST-200
SST-150*
SST-110*
SST-111*
SST-100
SST-060*
SST-050
150
100
SST-040
Type
0.5 1 2 3 5 7 10 15 20 30 50 75 100 150 250
250
250
175
Steam parameters up to:
65 bar, 480 °C
103 bar, 505 °C
110 bar, 520 °C
120 bar, 520 °C
165 bar, 565 °C
30 bar, 400 °C
170 bar, 565 °C
165 bar, 585 °C
165 bar, 585 °C
140 bar, 540 °C
40 bar, 400 °C
131 bar, 530 °C
101 bar, 500 °C
131 bar, 530 °C
131 bar, 530 °C
5
7
8
15
19
25
31
36
50
5 10 15 20 25 30 35 40 45 50
Siemens industrial steam turbinesThe complete product portfolio
Siemens industrial gas turbinesThe complete product portfolio
Frequency
50 Hzor
60 Hz
Type Power Output (MW)
SGT-100
SGT-200
SGT-300
SGT-400
SGT-500
SGT-600
SGT-700
SGT-750
SGT-800
*Steam turbine types mostly used for biomass applications
![Page 16: Steam Turbine - biomass](https://reader033.fdocuments.net/reader033/viewer/2022042600/588910f91a28ab4a5c8b5a33/html5/thumbnails/16.jpg)
Published by and copyright © 2013:Siemens AG Energy Sector Freyeslebenstrasse 1 91058 Erlangen, Germany
Siemens AG Energy Sector Oil & Gas Division Wolfgang-Reuter-Platz 47053 Duisburg, Germany
Siemens AG Lutherstrasse 51 02826 Goerlitz, Germany
Siemens Turbomachinery Equipment GmbH Heßheimer Straße 2 67227 Frankenthal (Pfalz), Germany
Siemens Energy Inc. 10730 Telge Road Houston, Texas 77095, USA
For more information, please contactour Customer Support Center.Phone: +49 180 524 70 00Fax: +49 180 524 24 71(Charges depending on provider)
Energy Service DivisionOrder No. E50001-G410-A115-X-4A00Printed in GermanyDispo 34806, K12 120254, P WS 0313
Printed on elementary chlorine-freebleached paper.
All rights reserved.Trademarks mentioned in this document are the property of Siemens AG, its affiliates, or their respective owners.
Subject to change without prior notice.The information in this document contains general descriptions of the technical options available, which may not apply in all cases. The required technical options should therefore be specified in the contact.