Starflex Contraption v1 - Russ Morris. What I see
5
Starflex Contraption v1 - Russ Morris www.russmorris.com • flickr.com/photos/russmorris russpix @ gmail.com Starflex Contraption v1 Kodak Brownie Starflex • Through the Viewfinder Russ Morris 2008.01.05 Thick black paper Opaque Tape Straight Edge Exacto/Utility Knife Compass/Circle Template 1. Cut out four panels. The front panel should start out 2 7/8” wide by 11” tall. The back panel should start out 2 7/8" wide by 10” tall. Both the left and right panels should start out 2 15/16” wide by 8 3/4” tall. Mark panel names on inside. 2. Cut each side panel to shape using the dimensions found in the following pages. Cut the front and back panels to shape. Using either a compass or circle template and the dimensions provided, draw then cut out the opening for the Starflex viewing and taking lens. I round the corners at the bottom of the front and back panel to make a cleaner fit. 3. Tape together all four panels on the outside using an opaque tape. Leave about 1/16" between panels. At this point the contraption will have three hinges. Do not complete channel! 4. Add tape to the top of the channel, inside and out to avoid damage from the camera. 5. Tape the last two panels together on the outside to complete the channel. 6. You can add tape around all edges if you're concerned about damage, but it's not really necessary. NOTE! The height of this contraption is based on my macro lens, which is 130mm. You may have to modify the height to accommodate your particular camera set-up.
Transcript of Starflex Contraption v1 - Russ Morris. What I see
Starflex Contraption v1 - Russ Morriswww.russmorris.com • flickr.com/photos/russmorris
Starflex Contraption v1Kodak Brownie Starflex • Through the Viewfinder
Russ Morris2008.01.05
Thick black paperOpaque TapeStraight EdgeExacto/Utility KnifeCompass/Circle Template
1. Cut out four panels. The front panel should start out 2 7/8” wide by 11” tall. The back panel should start out 2 7/8" wide by 10” tall. Both the left and right panels should start out 2 15/16” wide by 8 3/4” tall. Mark panel names on inside.
2. Cut each side panel to shape using the dimensions found in the following pages. Cut the front and back panels to shape. Using either a compass or circle template and the dimensions provided, draw then cut out the opening for the Starflex viewing and taking lens. I round the corners at the bottom of the front and back panel to make a cleaner fit.
3. Tape together all four panels on the outside using an opaque tape. Leave about 1/16" between panels. At this point the contraption will have three hinges. Do not complete channel!
4. Add tape to the top of the channel, inside and out to avoid damage from the camera.
5. Tape the last two panels together on the outside to complete the channel. 6. You can add tape around all edges if you're concerned about damage, but it's not really necessary.
NOTE! The height of this contraption is based on my macro lens, which is 130mm. You may have to modify the height to accommodate your particular camera set-up.
3/4" Diameter
2 7/8"
10"
2"
BACK INSIDEStarflex Contraption v1 - Russ Morris
www.russmorris.com • flickr.com/photos/[email protected]
Align all top edges for assemblySl
ight
mod
ifica
tions
may
be
requ
ired
whi
le p
uttin
g yo
ur
cont
rapt
ion
toge
ther
. No
guar
ante
es. N
o re
fund
s. N
ot g
ood
with
any
oth
er o
ffer.
Your
mile
age
may
var
y. P
leas
e ha
ve
fun,
but
be
dam
n ca
refu
l with
that
exa
cto
knife
!
B R F L
2 15/16"
8 3/4"
1/4"
2 1/16"
RIGHT INSIDEStarflex Contraption v1 - Russ Morris
www.russmorris.com • flickr.com/photos/[email protected]
Align all top edges for assemblySl
ight
mod
ifica
tions
may
be
requ
ired
whi
le p
uttin
g yo
ur
cont
rapt
ion
toge
ther
. No
guar
ante
es. N
o re
fund
s. N
ot g
ood
with
any
oth
er o
ffer.
Your
mile
age
may
var
y. P
leas
e ha
ve
fun,
but
be
dam
n ca
refu
l with
that
exa
cto
knife
!
B R F L
3/4" Diameter
1 1/4" Diameter
2 7/8"
11”
2 5/8”
1/4"
1 7/8”
FRONT INSIDEStarflex Contraption v1 - Russ Morris
www.russmorris.com • flickr.com/photos/[email protected]
Align all top edges for assemblySl
ight
mod
ifica
tions
may
be
requ
ired
whi
le p
uttin
g yo
ur
cont
rapt
ion
toge
ther
. No
guar
ante
es. N
o re
fund
s. N
ot g
ood
with
any
oth
er o
ffer.
Your
mile
age
may
var
y. P
leas
e ha
ve
fun,
but
be
dam
n ca
refu
l with
that
exa
cto
knife
!
B R F L
2 15/16"
8 3/4"
1/4"
2 1/16"
LEFT INSIDEStarflex Contraption v1 - Russ Morris
www.russmorris.com • flickr.com/photos/[email protected]
Align all top edges for assemblySl
ight
mod
ifica
tions
may
be
requ
ired
whi
le p
uttin
g yo
ur
cont
rapt
ion
toge
ther
. No
guar
ante
es. N
o re
fund
s. N
ot g
ood
with
any
oth
er o
ffer.
Your
mile
age
may
var
y. P
leas
e ha
ve
fun,
but
be
dam
n ca
refu
l with
that
exa
cto
knife
!
B R F L
![DAVID RAKOWSKI: WINGED CONTRAPTION · PDF filePIANO CONCERTO (2005–06) [3] ... David Rakowski has become one of the ... David Rakowski , Piano Concerto, Winged Contraption Winged](https://static.fdocuments.net/doc/165x107/5a78eb117f8b9ae6228ef029/david-rakowski-winged-contraption-concerto-200506-3-david-rakowski-has.jpg)
