STAR1M - cdviberica.com · STAR1M - Centrale autonome / Lecteur Mifare® Suppression de tous les...
Transcript of STAR1M - cdviberica.com · STAR1M - Centrale autonome / Lecteur Mifare® Suppression de tous les...
-
cdvigroup.com 1
Le choix de l’installateurcdvigroup.com
Français
English
FR
EN
STAR1MCentrale autonome/Lecteur Mifare® 13,56MHzStandalone Access Control System / 13,56 MHz Mifare® reader
-
cdvigroup.com2
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
1] PRÉSENTATION DU PRODUIT
- Produit 2 en 1 : fonctionnement centrale autonome fonctionnement lecteur Mifare® (13,56 MHz)- Électronique résinée- Signalisation lumineuse et sonore- 3m de câble (10 brins- AWG28)- Disponible en noir- Capacité : 300 badges (autonome)
Dimensions (L x l x P) : 130 x 41 x 28 mmTechnologie : 13,56 MHzProtocole : Mifare® classicAlimentation : 12 V DCConsommation : 200 mAWiegand 26/30/44 bits (lecteur Mifare®)
IP54
-25°C à +70°C
Certification CE
DEEE
Certification FCC CFR 47part 15 compliance
2] RAPPELS ET RECOMMANDATIONSSTAR1M
Recommandations d’installationPour sécuriser l’installation, n’oubliez pas de placer la varistance sur le système de verrouillage en parallèle sur les bornes de l’alimentation.
Câble préconiséCâble 10 conducteurs (AWG28)
Alimentations préconisées ADC335 et BS60 (lorsque le produit n’est alimenté ni par la centrale, ni par le contrôleur de porte [INTBUSW]).
EnvironnementSi vous installez ce produit dans un environnement marin/salin, il est préconisé de passer du vernis en bombe
sur les contacts après câblage afin de pré-venir le risque d’oxydation.
Ce produit est livré avec une varistance. Celle-ci doit être montée directement sur les bornes de la gâche (ventouse, moteur,…) commandée par l’équipement. Si l’appareil fonctionne avec plusieurs gâches, chacune doit être équipée de varistance. La varistance limite les surtensions provoquées par le bobinage de la gâche – effet de self. Dans le cas où la ventouse utilisée est du type “Shear Lock”, celle-ci doit être alimentée par une alimentation indépendante du STAR1M.
Joint d’étanchéité
Vis TF 3x30
Cheville plastique S5
Embout tournevis TORX®
Vis TORX® 3x8 Varistance Badge METAL
STAR1M 1 2 2 1 1 1 1
3] ÉLÉMENTS FOURNIS
Pour un éclairage optimal,
attention de ne pas plier le câble à
l’intérieur du produit.
R76,7
R35,
4
7
60
30
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son autorisation.This document is the exclusive property of CDVI and it may not be disclosed to others without permission.
31, av du Gal Leclerc93691 PANTIN CEDEXF R A N C ETel : 33(0)148910102Fax : 33(0)148912121www.cdvi.com
Plan M1806-VdE
Edition 00
Date 01/10/2009
ECHELLE 1:1
A4V
DES.: A. Broustal
Matière : ... Tolérance gale : 0.1 Etat de surface : Ra 3,2
A0228015Badge PP New
plan coté pour dépôt "dessin&modèle" C.A.: ...
Vol. (mm3) : Poids (g) :
-
cdvigroup.com 3
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
1 A l’aide du fond, placez les marques pour fixer le produit. Percez le support de montage au niveau des marques (diamètres préconi-sés : Ø5 mm et Ø15 mm). Grâce au schéma de câblage, prévoyez la sortie des câbles cachés dans la surface ou à l’extérieur (moulure).
4] MONTAGE
2 Placez le joint au dos du fond en commençant par le bas. (fig. a). Le joint doit dépasser d’environ 2 mm au niveau du sommet de la partie arrière du lecteur (fig. b).
3 Placez les chevilles dans les trous, passez le câble et raccordez-le (voir schéma de câblage page 4), puis fixez le lecteur avec la vis TORX® grâce à l’outil TORX® (fig. c). N’oubliez pas de placer la varistance au niveau du système de verrouillage (Voir page 2 “Rappels et recommandations”).
Fig. aFig. b
Ø 15
Ø 5
Fig. c
-
cdvigroup.com4
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
6] SCHÉMA DE CÂBLAGE
C56
C58
C61
1
MM10
4
3
2
1 ON
ON
ON
ON
L7
Q6
Q7
Q8
R77
R78
R79
P1
1P3
BZ3
C6
C24
C59
-+
MM1
MM14
CR3
+
-
CR10
CR25
CR26
CR24
MM3
MM15
CR12
CR13
CR15
I1
+
-
+
-
MM16
CR22
P2
-
+
CR19
CR21
CR20
CR28
CR27
CR29
CR11R70R67
R68R64
R69R65
C68
CR30
STAR1MRaccordements
Centrale autonome Lecteur Mifare®Rouge 12 V DC 12 V DC
Noir 0 V 0 V
Vert / Data 0
Blanc / Data1
Bleu Contact relais normalement ouvert - NO /
Gris Commun - C /
Violet Contact relais normalement connecté - NC /
Marron Bouton poussoir de sortie Entrée buzzer
Jaune / Entrée voyant vert
Orange / Entrée voyant rouge
5] FONCTIONNEMENT
Centrale autonome (liste blanche)
Lecteur Mifare® (WIEGAND)
1 OFF ON
2OFF ON OFF ON
Changer badge Maître
Fonctionnement NORMAL
Option du Dipswitch 3 44 bits
3 Non attribuéOFF ON
26 bits 30 bits
4 Non attribué
Voyants au démarrage : - Vert (1s)- Rouge (1s)- Bleu + BIP (1s)
Voyants en fonctionnement général :- Repos : Bleu- Passage badge : Vert ou rouge
Les différentes positions des Dipswitchs permettent de passer le STAR1M en Centrale autonome ou en Lecteur Mifare®.
Fonctionnement
Dipswitch
-
cdvigroup.com 5
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
7] PROGRAMMATIONAvant la mise sous tension, sélectionnez le mode de gestion (lecteur Mifare® ou centrale autonome).
1] Lecteur wiegand Mifare® (DIP1 sur ON)- vert- rouge- bleu + buzzer (séquence de démarrage)
2] Centrale autonome (DIP1 sur OFF) = réglage usine- vert- rouge- bleu + buzzer (séquence de démarrage)- jaune/vert : attente présentation du badge Maître (lors de la 1ère mise sous tension)
1
ON
2
ON
3
ON
4
ON
ON ON ON ON
1 2 3 4
ON
OFF
ON
OFF
- Conforme Mifare® - ISO 14443A (Mifare® classic).- Programmation via le badge Maître directement sur le lecteur : - Le badge Maître et utilisateurs s’enregistrent directement sur le lecteur- Capacité : 1 badge Maître + 300 badges utilisateurs (liste blanche)- Gestion 1 porte : 1 relais NO/NC- Mode «LISTE BLANCHE» : permettant de fonctionner qu’avec les badges pré-enregistrés.- 1 entrée bouton poussoir - Fonctionne avec les badges METAL, PVP (Mifare®), les cartes BV (ISO Mifare® format carte de crédit) et ERV.
8] FONCTIONNEMENT DE LA CENTRALE AUTONOME
V
V
BP
V
ADC335
Exemple de raccordement du fonctionnement centrale autonome12 VDC(-10%/+20%)
-
cdvigroup.com6
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
1
ON
2
ON
3
ON
4
ON
Fonctionnement normal : - Basculer DIP2 en ON après enregistrement du badge MaîtreBadge reconnu : - Voyant vert + BIP + activation relais pendant toute la durée de temporisation d’ouverture porteBadge non reconnu :- Voyant rouge + BIP
Créer ou remplacer un badge Maître- Basculer DIP2 en OFF - BIP + voyant jaune jusqu’à la présentation d’un badge- Présenter le badge Maître voulu devant le lecteur- BIP puis le voyant s’éteint Plus aucun badge n’est pris en compte- Basculer le DIP2 en ON pour quitter le mode
Créer/ajouter des badges utilisateurs (max. 300) ?- Présenter le badge Maître, le lecteur passe en programmation (voyant jaune + BIP)- Présenter chaque badges utilisateurs un à un; 10s après le dernier badge présenté = sortie du mode programmation- Présentation badge : si badge non enregistré, voyant vert + BIP puis retour voyant jaune si badge déjà enregistré, voyant éteint + BIP puis retour voyant jaune. - Chaque présentation de badge remet la temporisation à 0- Sortie du mode de programmation : BIP puis retour au voyant bleu
Effacer des badges utilisateurs - Présenter le badge Maître, le lecteur passe en programmation (le voyant jaune + BIP)- Lancement d’une temporisation de 10s avant la sortie du mode de programmation- Présenter consécutivement deux fois le même badge pour le supprimer- Présentation d’un badge déjà enregistré : voyant éteint + BIP puis retour voyant jaune- Présenter une deuxième fois le même badge pour le supprimer : voyant rouge + bip puis retour au voyant jaune- Attention si le badge est inconnu, cela va enregistrer le badge - Chaque présentation badge remet la temporisation à 0- Sortie du mode de programmation : BIP puis retour au voyant bleu
ON
OFF
1
ON
2
ON
3
ON
4
ON ON
OFF
1
ON
2
ON
3
ON
4
ON ON
OFF
Raccordement de la commande d’ouverture : La commande d’ouverture est maintenue pendant 5 secondes par défaut.La temporisation de porte est modifiable de 2 à 20 secondes.
-
cdvigroup.com 7
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
Suppression de tous les badges (rétablissement de la configuration par défaut)- Couper l’alimentation du STAR1M / Basculer le DIP1 sur ON- Rétablir l’alimentation du STAR1M. (Passage en mode lecteur Mifare®)- La voyant blanc/rouge s’active pendant l’effacement de la mémoire.- L’effacement de la mémoire est suivi de la séquence de démarrage (vert, rouge, bleu + BIP)- Attendre la fin de la séquence de démarrage puis couper l’alimentation du STAR1M.- Basculer le DIP1 et DIP2 sur OFF (mode centrale autonome activé)
Programmation du temps d’ouverture du relais de serrure- Présenter le badge Maître, voyant jaune + BIP (mode programmation)- Lancement d’une temporisation de 10s avant la sortie du mode de programmation- Appuyer sur le bouton poussoir. Chaque pression du BP = 1 seconde. Exemple : pour 10 sec, faire 10 pressions du BP, maxi 20 secondes- Sortie du mode programmation au bout de 10s d’inactivité- Clignotement voyants blanc et rouge équivalent aux nombres de seconde configurée + BIP- Sortie du mode de programmation :BIP puis retour au voyant bleu.
1ON 2ON 3ON 4ON ONOFF
1
ON
2
ON
3
ON
4
ON ON
OFF
9.1 Format de sortie WIEGAND 26, 30 et 44 bitsFormat Wiegand 26 bits
Format 26 bits hexadécimal. La communication s’effectue par une liaison de type Wiegand 26 bits (signaux : DATA1, DATA0). La trame est constituée d’une totalité de 26 bits et se décompose ainsi :
1. 1ère parité : 1 bit - parité de 12 premiers bits.Code de badge : 3 mots d’un octet représentant des 6 derniers termesChaque mot est transmis bit de poids fort en premier.
2. 2ème parité : 1 bit - parité impaire des 12 derniers bits
Le code émis est 166A37 en hexadécimal
Parité 1 :
Parité 2 :
Bit 1 Bit 2 à bit 25 Bit 26
Parité paire sur bit 2 à bit 13 Donnée (24 bits) Parité impaire sur bit 14 à bit 25
Exemple : pour un badge dont le code hexadécimal est 00166A37
1 0001 0110 0110 1010 0011 0111 0
Parité 1 1 6 6 A 3 7 Parité 2
0 si le nombre de 1 dans le bit 14 à bit 25 est impair, 1 si le nombre de 1 dans le bit 14 à bit 25 est pair.
0 si le nombre de 1 dans le bit 2 à 13 est pair,1 si le nombre de 1 dans le bit 2 à 13 est impair,
ON
9] FONCTIONNEMENT LECTEUR MIFARE®
-
cdvigroup.com8
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
Format Wiegand 30 bits
Format 30 bits hexadécimal. La communication s’effectue par une liaison de type Wiegand 30 bits (signaux : DATA1, DATA0). La trame est constituée d’une totalité de 30 bits et se décompose ainsi :
1. 1ère parité : 1 bit - parité de 14 premiers bits.Code de badge : 7 quartets représentant le code du badgeChaque mot est transmis bit de poids fort en premier.
2. 2ème parité : 1 bit - parité impaire des 12 derniers bits
Bit 1 Bit 2 à bit 29 Bit 30
Parité paire sur bit 2 à bit 15 Donnée (28 bits) Parité impaire sur bit 16 à bit 29
Exemple : pour un badge dont le code hexadécimal est 00166A37
0 0000 0001 0110 0110 1010 0011 0111 1
Parité 1 0 1 6 6 A 3 7 Parité 2
Le code émis est 0166A37 en hexadécimal
Parité 1 :
Parité 2 :
Format Wiegand 44 bits
Format 44 bits hexadécimal. La communication s’effectue par une liaison de type Wiegand 44 bits (signaux : DATA1, DATA0). La trame est constituée d’une totalité de 44 bits et se décompose ainsi :
Données : 10 chiffres hexadécimaux (octet de poids fort en premier), Chaque chiffre hexadécimal = 4 bits (bits de poids fort en premier)LRC : 4 bits = OU exclusif entre les chiffres de la donnée (bit de poids fort en premier)
Bit 1 à bit 40 Bit 41 à bit 44
Code du badge LRC
Exemple : pour un badge dont le code hexadécimal est 001950C3
0000 0000 0000 0000 0001 1001 0101 0000 1100 0011 0010
0 0 0 0 1 9 5 0 C 3 2
LRC
0 si le nombre de 1 dans le bit 16 à bit 29 est impair, 1 si le nombre de 1 dans le bit 16 à bit 29 est pair.
0 si le nombre de 1 dans le bit 2 à 15 est pair,1 si le nombre de 1 dans le bit 2 à 15 est impair,
Le code émis est 00001950C3 en hexadécimal
-
cdvigroup.com 9
MANUEL D’INSTALLATION FRSTAR1M - Centrale autonome / Lecteur Mifare®
PARAMÉTRAGEVOYANT VERT
PARAMÉTRAGEVOYANT ROUGE
VERT ACCÈS AUTORISÉROUGE ACCÈS REFUSÉBLEU EN ATTENTE
ÉTATVOYANTS
9.3 Paramétrage des voyants sur le système CENTAUR
9.2 Paramétrage des voyants sur le système ATRIUM
PARAMÉTRAGEVOYANT VERT
PARAMÉTRAGEVOYANT ROUGE
VERT ACCÈS AUTORISÉROUGE ACCÈS REFUSÉBLEU EN ATTENTE
ÉTATVOYANTS
-
cdvigroup.com10
1] PRODUCT PRESENTATION - 2-in-1 product: - standalone Access control system operation - Mifare® reader (13.56 MHz) operation- Resin-coated electronics- Audible and visual feedback- 3m of cable (10 leads - AWG28)- Available version black- Up to 300 cards (standalone)
IP54
-25°C à +70°C
Certification CE
DEEE
FCC Certification CFR 47 part 15 compliance
STAR1M
Dimensions (L x W x D): 130 x 41 x 28 mmTechnology: 13.56 MHzProtocol: Mifare® classicPower supply: 12 V dcConsumption: 200 mAWiegand 26/30/44 bits (reader Mifare®)
2] REMINDERS AND RECOMMENDATIONS
Installation recommendationsTo protect the device from back-emf, do not forget to install the varistor across the lock terminals, in parallel.
Recommended cable10-lead cable (AWG28)
Recommended power suppliesADC335 and BS60 (in case the reader is powered neither by the controller nor by the reader controller [INTBUSW]).
EnvironmentWhen in a humid area or close to the sea, we recommend applying varnish to the terminals to avoid oxidation.
This product is shipped with a varistor.The varistor must be connected directly to the locking system terminals (electric strikes, electromagnet, or lock) operated by the device. If the device functions with several locking systems, each one must be fitted with a varistor. The varis-tor limits overload produced by the strike coil, known as self-effect or back-emf. If you are using a “Shear Lock”, electro-magnet or other type of electric lock, we recommend the use of dedicated power supply for the lock.
For optimum lighting, be
careful to not fold the cable
inside the product.
3] MOUNTING KIT
Leaktight seal
TF 3x30 Screws
S5 Plastic anchor
TORX® Screwdriver tip
TORX® 3x8 Screws
Varistor METAL card
STAR1M 1 2 2 1 1 1 1
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
R76,7
R35,
4
7
60
30
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son autorisation.This document is the exclusive property of CDVI and it may not be disclosed to others without permission.
31, av du Gal Leclerc93691 PANTIN CEDEXF R A N C ETel : 33(0)148910102Fax : 33(0)148912121www.cdvi.com
Plan M1806-VdE
Edition 00
Date 01/10/2009
ECHELLE 1:1
A4V
DES.: A. Broustal
Matière : ... Tolérance gale : 0.1 Etat de surface : Ra 3,2
A0228015Badge PP New
plan coté pour dépôt "dessin&modèle" C.A.: ...
Vol. (mm3) : Poids (g) :
-
cdvigroup.com 11
4] MOUNTING
Fig. aFig. b
Ø 15
Ø 5
Fig. c
3
1 2 Trace the markings to fix the product using the back casing. Drill the fixing support using the markings (recommended diameters: Ø5 mm and Ø15 mm). Using the wiring diagram, plan for the cable exits hidden under the sur-face or outside (trunking).
Fit the seal on the back plate starting from the bottom. (fig. a). The seal must overlap the back part of the reader by about 2 mm (fig. b).
Fit the anchors in the holes, pass the cable and connect it (see wiring diagram on page 14), then fix the reader using the TORX® screw using the TORX® tool (fig. c). Remember to fit the varistor at the locking system level (see “Reminders and recommendations” on page 12).
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
-
cdvigroup.com12
5] OPERATION
Standalone system (white list)
Mifare® reader (WIEGAND)
1 OFF ON
2OFF ON OFF ON
Change the Master card
NORMAL operation
Dipswitch 3 option 44 bits
3 Not assignedOFF ON
26 bits 30 bits
4 Not assigned
Operation
Dipswitch
The different dipswitch positions are used to switch the STAR1M to a standalone system or to a Mifare® reader.
6] WIRING DIAGRAM
C56
C58
C61
1
MM10
4
3
2
1 ON
ON
ON
ON
L7
Q6
Q7
Q8
R77
R78
R79
P1
1P3
BZ3
C6
C24
C59
-+
MM1
MM14
CR3
+
-
CR10
CR25
CR26
CR24
MM3
MM15
CR12
CR13
CR15
I1
+
-
+
-
MM16
CR22
P2
-
+
CR19
CR21
CR20
CR28
CR27
CR29
CR11R70R67
R68R64
R69R65
C68
CR30
STAR1MConnetions
Standalone system Mifare® readerRed 12 V dc 12 V dc
Black 0 V 0 V
Green / Data 0
White / Data1
Blue Normally open relay contact - NO /
Grey Common - C /
Purple Normally connected relay contact - NC /
Brown Exit push button Buzzer input
Yellow / Green LED input
Orange / Orange LED input
LEDs on start-up:- Green (1s)- Red (1s)- Blue + BEEP (1s)
LEDs during routine operation:- Standby: Blue- When a badge is read: Green or red
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
-
cdvigroup.com 13
7] PROGRAMMING
1
ON
2
ON
3
ON
ON ON ON
1 2 3
ON
OFF
ON
OFF
Before powering on, select the management mode (Mifare® reader or standalone system).
1] Mifare® wiegand reader (DIP1 ON)- green- red- blue + buzzer (starting sequence)
2] Standalone system (DIP1 OFF) = factory setting- green- red- blue + buzzer (starting sequence)- yellow/green: waiting for the Master card to be read (when powering on for the 1st time)
8] STANDALONE SYSTEM OPERATION- Mifare® compliant - ISO 14443A (Mifare® classic).- Programming using the Master card directly on the reader:- The Master and user cards are registered directly on the reader- Capacity: 1 Master card + 300 user cards (white list)- Management of 1 door controller : 1 relay NO/NC - “WHITE LIST” mode: can only be operated using pre-registered cards- 1 push button entry- Operates with METAL, PVP (Mifare®) badges, BV cards (ISO Mifare® credit card format) and ERV cards.
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
ON
4
ON
4
V
V
BP
V
ADC335 12 VDC(-10%/+20%)
Example of a standalone system operation connection
-
cdvigroup.com14
Normal operation:- Position DIP2 to ON after registering the Master cardCard recognised:- Green LED + BEEP + relay activated for the door open timer durationCard not recognised:- Red LED + BEEP
To create or replace a Master card- Position DIP2 to OFF- BEEP + yellow LED until a card is passed- Place the Master card in question in front of the reader- One BEEP and the LED turns off. No other cards are taken into account- Position DIP2 to ON to exit this mode
1
ON
2
ON
3
ON
4
ON ON
OFF
1
ON
2
ON
3
ON
4
ON ON
OFF
1
ON
2
ON
3
ON
4
ON ON
OFF
To create/add user cards (max. 300)- Present the Master card in front of the reader, the reader switches to programming mode (yellow LED + BEEP)- Pass the user cards in front of the reader one after the other; 10 seconds after the last card is registered, programming mode is exited.- Presenting cards if the card is not registered, green LED + BEEP then return to yellow LED if the card was already registered, LED off + BEEP then return to yellow LED.- Each time a card is presented, the timer is reset to 0- Exit from programming mode: BEEP and return to the blue LED
To erase user cards- Present the Master card in front of the reader, the reader switches to programming mode (the reader’s yellow LED turns on, followed by a BEEP)- A 10s timer is triggered until programming mode is exited- Pass the same card in front of the reader twice in a row to delete it- If the card was already registered: LED off + BEEP then return to yellow LED- Pass the same card in front of the reader again to delete it: red LED + BEEP then return to yellow LED- Caution, if the card is unknown it will register it- Each time a card is presented, the timer is reset to 0- Exit from programming mode: BEEP and return to the blue LED
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
Open control connection:By default, the open control is maintained for 5 seconds.The door timer can be set from 2 to 20 seconds.
Programming the lock relay open time- Present the Master card in front of the reader, the reader switches to programming mode (the yellow LED turns on, followed by a BEEP)- A 10s timer is triggered until programming mode is exited- Press the push button. Each time the PB is pressed = 1 second. For example: for 10 secs., press the PB 10 times. Max. 20 seconds
-
cdvigroup.com 15
1
ON
2
ON
3
ON
4
ON ON
OFF
1
ON
2
ON
3
ON
4
ON ON
OFF
- Programming mode is exited after 10 seconds without any actions- The white and red LED flash the number of times that correspond to the configured number of seconds, followed by a BEEP- Exit from programming mode: BEEP and return to the blue LED.
Deleting all cards (return to the default configuration)- Cut the STAR1M power supply / Position DIP1 to ON- Turn the STAR1M power supply back on. (Switch to Mifare® reader mode)- The white/red LED is activated while the memory is deleted.- The deletion of the memory is followed by the start-up sequence (green, red, blue + BEEP)- Wait for the start sequence to end and then cut the STARM1 power supply.- Position DIP1 and DIP2 to OFF (switch to standalone system mode)- The device waits for a new Master card to be placed in front of the reader- Turn the power supply back on, the STARM1 is ready for reprogramming.
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
9] MIFARE® READER OPERATION9.1 WIEGAND 26, 30 and 44 bit output format
26-bit Wiegand Output
Hexadecimal 26 bit format. Communication uses a Wiegand 26 bit type signal (signals: DATA1, DATA0). The frame is composed of a total of 26 bits split up as follows:
1. First parity: 1 bit - parity for the first 12 bits.Badge code: 3 one byte words representing the 6 last termsEach word is sent with the most significant bit first.
2. Second parity: 1 bit - odd parity for the last 12 bits
Bit 1 Bit 2 à bit 25 Bit 26
Even parity on bit 2 to bit 13 Data (24 bits) Odd parity on bit 14 to bit 25
For example: for a card with hexadecimal code 00166A37
1 0001 0110 0110 1010 0011 0111 0
Parity 1 1 6 6 A 3 7 Parity 2
The transmitted hexadecimal code is 166A37
Parity 1:
Parity 2:
0 if the number of ‘1’s in bits 2 to 13 is even, 1 if the number of ‘1’s from bit 2 to 13 is odd.
0 if the number of ‘1’s in bits 14 to 25 is odd, 1 if the number of ‘1’s from bit 14 to 25 is even.
-
cdvigroup.com16
30-bit Wiegand Output
Hexadecimal 30 bit format. Communication uses a Wiegand 30 bit type signal (signals: DATA1, DATA0). The frame is composed of a total of 30 bits split up as follows:
1. First parity: 1 bit - parity for the first 14 bits.Badge code: 7 half byte representing the card codeEach word is sent with the most significant bit first.
2. Second parity: 1 bit - odd parity for the last 12 bits
Bit 1 Bit 2 à bit 29 Bit 30
Even parity on bit 2 to bit 15 Data (28 bits) Odd parity on bit 16 to bit 29
For example: for a card with hexadecimal code 00166A37
0 0000 0001 0110 0110 1010 0011 0111 1
Parity 1 0 1 6 6 A 3 7 Parity 2
The transmitted hexadecimal code is 0166A37
Parity 1:
Parity 2:
0 if the number of ‘1’s in bits 2 to 15 is even, 1 if the number of ‘1’s from bit 2 to 15 is odd.
0 if the number of ‘1’s in bits 16 to 29 is odd, 1 if the number of ‘1’s from bit 16 to 29 is even.
44-bit Wiegand format Output
Hexadecimal 44 bit format. Communication uses a Wiegand 44 bit type signal (si-gnals: DATA1, DATA0). The frame is composed of a total of 44 bits split up as follows:
Data: 10 hexadecimal digits (most significant byte first). Each hexadecimal digit = 4 bits (most significant bit first)LRC: 4 bits = OR restricted in between the digit of the date, MSBit first
Bit 1 à bit 40 Bit 41 à bit 44
Badge code LRC
For example: for a card with hexadecimal code 001950C3
0000 0000 0000 0000 0001 1001 0101 0000 1100 0011 0010
0 0 0 0 1 9 5 0 C 3 2
LRC
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
The transmitted hexadecimal code is 00001950C3
-
cdvigroup.com 17
9.3 LEDs management on the CENTAUR system
9.2 LEDs management on the ATRIUM system
GREEN ACCESS AUTHORISEDRED ACCESS DENIEDBLUE STANDBY
LED STATUS
GREEN ACCESS AUTHORISEDRED ACCESS DENIEDBLUE STANDBY
LED STATUS
GREEN LEDCONFIGURATION
RED LEDCONFIGURATION
GREEN LED CONFIGURATION
RED LEDCONFIGURATION
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
-
cdvigroup.com18
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
NOTES
-
cdvigroup.com 19
INSTALLATION MANUAL ENSTAR1M - Standalone Access control system / 13,56 MHz Mifare®reader
-
cdvigroup.com20
Reference : G0301FR1031V02Extranet : CDVI_IM STAR1M CMYK A5 FR-EN-02
Tout
es le
s in
form
atio
ns m
entio
nnée
s à
titre
indi
catif
sur
le p
rése
nt d
ocum
ent
(pho
tos,
des
sins
, ca
ract
éris
tique
ste
chni
ques
et
dim
ensi
ons)
peu
vent
var
ier
et s
ont
susc
eptib
les
de m
odifi
catio
ns s
ans
notifi
catio
n pr
éala
ble.
*G0301FR1031V02*
CDVI GroupFRANCE (Siège social/Headquarter)
Phone: +33 (0)1 48 91 01 02
CDVI FRANCE + EXPORT31, av. du Général Leclerc93500 PANTIN - FrancePhone: +33 (0)1 48 91 01 02www.cdvi.com
CDVI AMERICAS[CANADA - USA]Phone: +1 (450) 682 7945www.cdvi.ca
CDVI BENELUX[BELGIUM - NETHERLAND - LUXEMBOURG]Phone: +32 (0) 56 73 93 00www.cdvibenelux.com
CDVI TAIWANPhone: +886 (0)42471 2188www.cdvichina.cn
CDVI SUISSEPhone: +41 (0)21 882 18 41www.cdvi.ch
CDVI CHINA Phone: +86 (0)10 84606132/82www.cdvichina.cn
CDVI IBÉRICA[SPAIN - PORTUGAL]Phone: +34 (0)935 390 966www.cdviberica.com
CDVI ITALIAPhone: +39 0321 90 573 Fax: +39 0321 90 8018www.cdvi.it
CDVI MAROCPhone: +212 (0)5 22 48 09 40www.cdvi.ma
CDVI SWEDEN [SWEDEN - DENMARK - NORWAY - FINLAND]Phone: +46 (0)31 760 19 30www.cdvi.se CDVI UK [UNITED KINGDOM - IRELAND]Phone: +44 (0)1628 531300 www.cdvi.co.uk
Le choix de l’installateur cdvigroup.com
All t
he in
form
atio
n co
ntai
ned
with
in t
his
docu
men
t (p
ictu
res,
dra
win
g, f
eatu
res,
spe
cific
atio
ns a
nd d
imen
sion
s)co
uld
be p
erce
ptib
ly d
iffer
ent
and
can
be c
hang
ed w
ithou
t pr
ior
notic
e.