*Photo may include optional equipment.

With Tier 2 Engine installed

PLEASE CONTACT

www.hyundai-ce.com 2013.01 Rev 3

* Specifications and designs are subject to change without advance notice.

STANDARD EQUIPMENT

ElEcTRIcAl SySTEMAlternator, 55ABack up AlarmBatteries 2X 12V, 120AhGauge - Coolant temp - Fuel level - Brake Air pressure - TM temp. - TM oil pressure - Hour meter & volt meterIndication lamp - Parking - Charge - Brake low pressure - Engine oil pressure - High beamLight - 1 LED dome Light - 4 Work Light (2 Front, 2 Rear) - 2 Head light with high and low beam - 4 Turn signal - 2 Stop lightSwitch - Ignition Key, Start Stop Switch

- Battery master switch - Harzard - Beacon - Work lampStarter

cAbCigar lighterCoat hookTemperature control - heater - defroster - Wiper and washer, frontPersonal storage space: holder, can and cupRear view mirrors(1 inside)Rear view mirrors(2 outside)2" seat belt & adjustable suspension seat with armrestsSteering wheel with knobSun visor(front window)Tinted safety glassCabin with two doorsPedals - one accelerator pedal - one brake pedalRubber floor mat

ENgINEAntifreezeLow Emission, Tier 2SL763 : Engine - Weichai WD10G220E23SL733 : Engine - Yuchai YC6J125Z-T20Engine fuel priming pump(SL763)Fan guardFuel/water separatorFuel warmer(SL763)Precleaner, engine air intakeRadiator (de-aeration type)

PowER TRAINBrake : Service, caliper discParking brakeDifferential, conventionalTorgue converterPower shift transmissionTransmission oil coolerTire (23.5-25, 16PR, L3)

HyDRAUlIcSDiagnostic pressure tapsHydraulic oil tapsHydraulic oil cooler(SL763)

Hydraulic system - 2 spool, mechanical control for boom and bucket actuationSteering, load-sensing(SL763)

oTHERSArticulation locking barCounterweightDrawbar with pinErgonomically located and slip resistant, left & right - Handrails - Ladders - Platforms - StepsFront FendersHydraulic oil level sight gaugeLift and tie-down hooksLoader linkage, sealed Z-bar designCushioned steering stops

oPTIoNAl EQUIPMENT

Climate control : -Air conditioning onlyHeater & air conditioningBeacon lightElectromagnetic Fan clutch(SL763)High lift boomMP3 RadioSeat -2" seat belt & adjustable suspension seat with headrest

Sl763Bucket- 2.7 m3 Rock (Straight Edge)- 2.7 m3 GP bolt-on teeth- 2.8 m3 GP bolt-on cutting edge- 2.8 m3 Rock (Spade nose)- 3.1 m3 GP bolt-on cutting edge- 3.2 m3 GP bolt-on teeth- 3.3 m3 GP bolt-on cutting edge- 4.0 m3 Coal handling

Sl733Bucket- 1.5 m3 GP bolt-on teeth- 1.6 m3 GP bolt-on cutting edge- 1.8 m3 GP bolt-on cutting edge- 2.2 m3 Coal handling- 2.5 m3 Coal handling

HYUNDAI HEAVY INDUSTRIES. CO., LTD.1000 BANGEOJINSUNHWAN-DORO, DONG-GU, ULSAN, 682-792, KOREA TEL: (82)52-202-7722, 9807 FAX: (82)52-202-7720

Distributed by :

HYUNDAI(SHANDONG) HEAVY INDUSTRY MACHINERY CO., LTD.YITIANMEN DAJIE ZHONGDUAN, TAIAN, SHANDONGTHE PEOPLE'S REPUBLIC OF CHINATEL: (86)538-692-8989, FAX : (86)538-692-8991

Manufactured and

Assembled by :

02/03

*Photo may include optional equipment.

Hyundai Shandong(HSD) Wheel Loader Opens Up the Future

Excellent durability saves your costs of working.Outstanding power greatly enhances your productivity.

Strong Power, High Performance

Fan clutch (SL763 only) (option)

Fan’s speed is adjusted by temperature to reduce engine fuel consumption and noise. Engine durability is increased by warming up engine quickly.

Electric Shut off (SL763 only)When the circuit key turns off, it stops electromagnetic and closes the throttle.

Fuel Pre-filter and Fuel warmer (SL763 only)Electric Pump quickly removes air in fuel and improves start of the machine. Fuel warmer raises fuel temperature and improves low temperature at start. Moist eliminating filter filters impurities and moisture, and extends engine’s life and replacement cycle.

Powerful, Energy-saving and Environmentally Friendly EngineWeichai(SL763) and Yuchai(SL733) turbocharged engine are built for maximum power, reliability, and optimum fuel efficiency. These en-gines meet the emission standards EPA Tier II, EU Stage II.Weichai engine has power of 162kW at 2,000rpm. Electromagneticfan clutch(option) and fuel transfer pump reduce noise to make start easier and more energy saving.

Hyundai Shandong Wheel Loader shows maximum power at all times and greatly improves efficiency.

Reliable TransmissionHydrodynamic transmission is made up of double turbine torque converter (SL763 only) and power assist shift planetary transmission. It can meet the wheel loader in all require-ments of working situations.

04/05

*Photo may include optional equipment.

Durable and Sturdy AxleDurable and sturdy front and rear axle provides running stability, good performance even in poor jobsite conditions, and maximizes the opera-tion capability.

3

1

4

2

Higher ProductivityLong wheelbase makes the machine maintain longitudinal stability in a variety of operating conditions, and hinged center of the front and rear frame is placed at the center of the wheelbase, so that when the loader makes a turn, it makes wheelbase of the front and rear wheels overlap which increases tire life and operation stability.And higher fuel tank location effectively prevents fuel tanks from dam-aging and poses the maximum ground clearance.

❶ Higher Dump Clearance (without teeth)

SL763SL733

3,215 mm2,925 mm

❷ Longer WheelbaseSL763SL733

3,300 mm2,850 mm

SL763SL733

4,220 mm3,775 mm

❹ Bucket Max Pivot❸ Higher Fuel Tank LocationSL763SL733

565 mm480 mm

Enhanced Reliability and Durability

Sealed loader linkageO-shaped ring seal prevents leakage and makes maintenance easier. Dust Seal ex-tends service life and makes maintenance and repair efficient by blocking dust and preventing grease leakage.

Enhanced cooling SystemAluminum bar-plate type, large capacity radiator and coolers significantly improve thermal shock, impulse and vibration resistance and increase durability.

brake Disc ProtectorFront axle enhances protection of brake disc shield from smashing of heavy ob-jects.

Reliable center Pivot (SL763 only)

Firm and Durable Structural PartsExtend product life and ensure superior running function by using product structure of limited element analysis and optimization.

Double-tapered roller bearings extends service life, and lubrication and replacement cycle. (Comparison with joint bearings) : 100 hr 1,000 hr

The all-new, deluxe operating space is engineered with 3-D modeling for your ulti-mate control center. The wide, tinted and laminated front windshield has no framing cutting through to ensure excellent visibility.

Turn Limit Cushion3 layered rubber buffer structure enhanc-es impact resistance, reduces operator’s fatigue and extend service life.

06/07

*Photo may include optional equipment.

bucketHigh-alloy steel casting and wear-proof integrated cutting edge and teeth are suitable for all kinds of working environment.

Product structure of limited element analysis and optimization sufficiently improved durability and safety.

Operator Friendly Designed cab

Quiet and spacious interior room provides operators with a comfortable operating environment. All kinds of metering instruments are effectively laid out to improve convenience of operation.

08/09

*Photo may include optional equipment.

Suspended SeatIt can be adjusted to the position opti-mized for driver’s weight and size reducing operator’s fatigue.

Excellent Air circulation System Storage Spaces with Multiple FunctionsExcellent air conditioning and circulation system provide opera-tors with more comfortable working space.

centralized Monitoring PanelCentralized monitoring panel designed with simplicity of ergonomics that shows working conditions and warning lights at a glance.

Air Purification FilterIt effectively filters dust out of the cab to keep the air clean and fresh.

Operator can partially or fully open right side window when it’s needed.

Large side mirror ensures the operator’s driving safety.

Right Side window Holder large Side Mirror

Spacious Cab with Excellent ViewSpacious cab designed with ergonomics approach boasts low noise and excellent view, arc shaped front window, large rear window and side windows offer wide view in all directions.

Large capacity, air circulation and perfect defrost system make the space comfort-able for operators and membrane button is easy to operate.

Large Capacity Air Conditioning and Convenient Control (Option)

Radio with USB interface (Option)Radio with USB interface offers better sound for operators and makes operation more enjoyable.

Simple and Efficient Maintenance System

Quick and easy maintenance systems improve efficiency and cost saving. As a loader newly designed from the driver’s point of view, Hyundai Shandong wheel loader makes your operation more comfortable and convenient.

10/11

*Photo may include optional equipment.

Easy Access to Radiator counterweight and Rear warn-ing light

Headlight and Turn Signal

Operators can easily maintain and clean the radiator.Counterweight is beautifully designed and

warning lights are noticeable.

Lights are beautifully and durably de-signed.

Non-slip PlatformNon-slip platform and steps ensure operator’s safety.

Key-locking Fuel capThe location of fuel cap increased acces-sibility and key locking function is applied for machine protection.

Tilted ladder by 12 degrees is designed to make getting on and off easier and to en-hance comfortability for operators.

ladder of convenience and Safety

12o

Air filter is built in the rear of the hydraulic tank to make ease replacement and clean-ing of the filter.

Durable electrical control box is centralized to make easy maintenance for operator to check.

The hydraulic oil check sight gauge is in-stalled on the side of the hydraulic tank for the convenience of maintenance check from ground level.

Easy Replacement of Air Filter convenient and Safe Electrical control box

oil Sight gauge

Highly accessible engine compartment assures fast and easy mainte-nance.

Easy Access to Engine compartment

Rear engine hood is electrically opened with a large opening angle for easier maintenance.

Rear Engine Hood Electric lift control Switch

A master switch disconnects the battery power to protect the electrical system.

Master switch

SL763 SL733

12/13

Specifications & Dimensions SL 763

Torque converter type

4-elements, Double-turbine

Tire 23.5-25, L3

Travel speed

Forward 10.9 (6.8)

40.0 (24.9)

Reverse 14.9 (9.3)

1st

2nd

1st

km/h (mph)

TRANSMISSIoN

AxlES

Drive system Four-wheel drive system Hub reduction Planetary reduction at wheel end

Differential Conventional

Reduction ratio 22.847

HyDRAUlIc SySTEM

Type

Pump

System pressure

Open-Centered, tandem circuit system

(Bucket, Boom)

Gear type, 370 pm

190 kgf/cm2 (2,702 psi)

Maker/Model Weichai / WD10G220E23

Type

gross power 220 HP(162 kW) / 2,000rpm

Net power 206 HP(154 kW) / 2,000rpm

Maximum torque 92 kg.m(664 lb.ft) / 1,300~1,500rpm

No. of cylinders 6

bore x Stroke 126 mm (4.96”) x 130 mm (5.12”)

Displacement 9.726ℓ(594 cu in)

compression ratio 17.0 : 1

Air cleaner Dry, dual elements

Alternator 24V, 55 Amp

battery 2 x 12V, 120 Ah.

Starting motor 24V, 8.1 kW

ENgINE

4-cycle, water cooled,turbocharged, diesel,

direct injection

bRAKES

Service brakes

Parking brake

- Air over hydraulic brake system(Caliper disc type)

- Independent axle-by-axle system

Manual pneumatic controlleddrum brake on transmission

SERvIcE REFIll cAPAcITIES

280 liters (74.0 USgal)

44 liters (11.6 USgal)

20 liters (5.3 USgal)

50 liters (13.2 USgal)

Fuel tank

cooling system

crankcase

Transmission

28 liters (7.4 USgal)

28 liters (7.4 USgal)

150 liters (39.6 USgal)

260 liters (68.7 USgal)

Front axle

Rear axle

Hydraulic tank

Hydraulic system (including tank)

Bucket Type

A. Dumping clearance at max.

height and 45o dump angle.

Full lift

7ft height

C. Digging depth

on ground

at carry

E. Overall height (fully raised)

F. Bucket pivot max. height

3,220 (10’ 7”)

1,120 (3’ 8”)

1,780 (5’ 10”)

65 (2.6”)

8,250 (27’ 1”)

8,000 (26’ 3”)

5,660 (18’ 7”)

4,220 (13’ 10”)

B. Reach

D. Overall length

G. Front overhang

H. Wheelbase

I. Ground clearance

J. Height over exhaust

K. Height over cab

on ground

at carry

M. Dump angle

Clearance circle

with bucket

without bucket

2,820 (9’ 3”)

3,300 (10’ 10”)

430 (1’ 5”)

3,200 (10’ 6”)

3,480 (11’ 5”)

41

47

45

13,240 (43’ 5”)

2,950 (9’ 8”)

2,770 (9’ 1”)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

deg

deg

deg

mm (ft-in)

mm (ft-in)

mm (ft-in)

UNITDescription DescriptionSl763 UNIT Sl763

L. Roll-back angle

N. Overall width

DIMENSIoNS

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

General purpose bolt-on teeth

Type Tube type, loader design tires

Standard 23.5-25, 16 PR, L3

TIRES

Operating weight kg (lb)

Heaped m3(yd3)

Struck m3(yd3)

Breakout force-bucket kg (lb)

Straight kg (lb)

Full turn kg (lb)

Sl763

16,800 (37,040)

3.0 (3.9)

2.6 (3.4)

17,810 (39,260)

13,630 (30,050)

11,800 (26,010)

Description UNIT

Bucket capacity

Tipping load

ovERvIEw

STEERINg SySTEM

Type

Pump

Relief valve Setting

cylinder (Bore x Stroke)

Steering Angle

Hydraulic power steering

Gear type, 150 liters/min(39.6 gal/min)

160 kg/cm2(2,275 psi)

90 mm(3.5") x 440 mm(17.3")

40o (each direction)

bucket Type

Lift Circuit

Tilt Circuit

Manual operated lift and tilt circuit

The valve has four functions ; raise, hold, lower and float

The valve has three functions ; tilt back, hold and dump

Raise : 5.2 sec (with load)Dump : 0.8 secLower : 3.7 secTotal : 9.7 sec

cycle Time

Lift 160 mm(6.3") x 820 mm(32.3")Tilt 180 mm(7.1") x 545 mm(21.5")

cylinder

controls

14/15

Specifications & Dimensions SL 733

AxlES

Drive system Four-wheel drive system Hub reduction Planetary reduction at wheel end

Differential Conventional

Reduction ratio 20.26

HyDRAUlIc SySTEM

Type

Pump

System pressure

Open-Centered, tandem circuit system

(Bucket, Boom)

Gear type, 167 pm

160 kgf/cm2 (2,275 psi)

bucket Type

Lift Circuit

Tilt Circuit

Manual operated lift and tilt circuit

The valve has four functions ; raise, hold, lower and float

The valve has three functions ; tilt back, hold and dump

Raise : 5.2 sec (with load)Dump : 1.1 secLower : 3.0 secTotal : 9.3 sec

cycle Time

Lift 110 mm(4.3") x 785 mm(30.9")Tilt 160 mm(6.3") x 380 mm(15.0")

cylinder

controls

Maker/Model Yuchai / YC6J125Z-T20

Type

gross power 125 HP(92 kW) / 2,200rpm

Net power 117 HP(87 kW) / 2,200rpm

Maximum torque 51 kg.m(369 lb.ft) / 1,400~1,600rpm

No. of cylinders 6

bore x Stroke 105 mm (4.13”) x 125 mm (4.92”)

Displacement 6.494ℓ(396 cu in)

compression ratio 17.5 : 1

Air cleaner Dry, dual elements

Alternator 24V, 55 Amp

battery 2 x 12V, 120 Ah.

Starting motor 24V, 6 kW

ENgINE

4-cycle, water cooled,turbocharged, diesel,

direct injection

bRAKES

Service brakes

Parking brake

- Air over hydraulic brake system(Caliper disc type)

- Independent axle-by-axle system

Manual controlleddisc brake on transmission

SERvIcE REFIll cAPAcITIES

160 liters (42.3 USgal)

33 liters (8.7 USgal)

16 liters (4.2 USgal)

40 liters (10.6 USgal)

Fuel tank

cooling system

crankcase

Transmission

18 liters (4.8 USgal)

18 liters (4.8 USgal)

95 liters (25 USgal)

155 liters (40.9 USgal)

Front axle

Rear axle

Hydraulic tank

Hydraulic system (including tank)

Bucket Type

A. Dumping clearance at max.

height and 45o dump angle.

Full lift

7ft height

C. Digging depth

on ground

at carry

E. Overall height (fully raised)

F. Bucket pivot max. height

2,933 (9’ 7”)

1,150 (3’ 9”)

1,640 (5’ 5”)

87 (3.4”)

6,940 (22’ 9”)

6,890 (22’ 7”)

4,880 (16’)

3,775 (12’ 5”)

B. Reach

D. Overall length

G. Front overhang

H. Wheelbase

I. Ground clearance

J. Height over exhaust

K. Height over cab

on ground

at carry

M. Dump angle

Clearance circle

with bucket

without bucket

2,415 (7’ 11”)

2,850 (9’ 4”)

370 (1’ 3”)

2,760 (9’ 1”)

3,235 (10’ 7”)

43

49

45

11,770 (38’ 7”)

2,480 (8’ 2”)

2,300 (7’ 7”)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

deg

deg

deg

mm (ft-in)

mm (ft-in)

mm (ft-in)

UNITDescription DescriptionSl733 UNIT Sl733

L. Roll-back angle

N. Overall width

DIMENSIoNS

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

mm (ft-in)

General purpose bolt-on teeth

Type Tube type, loader design tires

Standard 17.5-25, 14 PR, L3

TIRES

Operating weight kg (lb)

Heaped m3(yd3)

Struck m3(yd3)

Breakout force-bucket kg (lb)

Straight kg (lb)

Full turn kg (lb)

Sl733

10,200 (22,490)

1.7 (2.2)

1.4 (1.8)

10,370 (22,860)

8,440 (18,610)

7,100 (15,650)

Description UNIT

Bucket capacity

Tipping load

ovERvIEw

Torque converter type

3-elements, Single-turbine

Tire 17.5-25, L3

Travel speed

Forward 7.4 (4.6)

13.3 (8.3)

23.9 (14.6)

39.5 (24.5)

Reverse 9.2 (5.7)

29.0 (18.0)

1st

2nd

3rd

4th

1st

2nd

km/h (mph)

TRANSMISSIoN

STEERINg SySTEM

Type

Pump

Relief valve Setting

cylinder (Bore x Stroke)

Steering Angle

Hydraulic power steering

Gear type, 83 liters/min(21.9 gal/min)

160 kg/cm2(2,275 psi)

70 mm(2.8") x 412 mm(16.2")

40o (each direction)