Standalone TCSM3i ETIP1-A Implementation for IPPWE (S15 TCSM HW)-Ver-1_0

DN09114157 Standalone TCSM3i ETIP1-A implementation for IP/PWE (S15 TCSM HW)Copyright 2013 Nokia Solutions and Networks. All rights reserved.CONFIDENTIALAPPROVED 1.0

1 (104)

Standalone TCSM3iETIP1-A implementationfor IP/PWE (S15 TCSMHW)Release Delivery: HW UpgradeProduct Family: Radio ControllersProduct: BSC3i 1000/2000, UpgradedFlexi BSC, TCSMRelease: S16 onwards

Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of itsproducts and services. We would like to encourage you as our customers and users to join us inworking towards a cleaner, safer environment. Please recycle product packaging and follow therecommendations for power use and proper disposal of our products and their components.

If you should have questions regarding our Environmental Policy or any of the environmental serviceswe offer, please contact us at Nokia Solutions and Networks for additional information.


2 (104)

Table of Contents1 Purpose .................................................................................................................................................. 72 Scope of applications .............................................................................................................................. 83 Using the document ................................................................................................................................ 9

3.1 General info ....................................................................................................................................................... 94 Introduction ........................................................................................................................................... 10

4.1 Standalone TCSM3i equipment after upgrade ................................................................................................... 114.1.1 A and Ater interface ETIP with full HW redundancy ..................................................................... 124.1.2 A interface ETIP Mixed configurations ......................................................................................... 13

5 Pre-requirements .................................................................................................................................. 135.1 Pre-requirements & Actions needed prior upgrade ............................................................................................ 135.2 Restrictions ..................................................................................................................................................... 135.3 Needed documentation .................................................................................................................................... 145.4 Needed equipment .......................................................................................................................................... 14

6 Fallback copying of the current package ................................................................................................ 157 BSC configuration printout (pre-check) .................................................................................................. 158 Licence installation and feature activation .............................................................................................. 159 Configuration example of Ater interface used in this instruction .............................................................. 1710 Master units in TCSM site ..................................................................................................................... 1811 TCSA rack cartridge position info .......................................................................................................... 2212 Ater interface ETIP1-A implementation for IP/PWE in Standalone TCSM ............................................... 23

12.1 Ater plug-in unit installation to BSC ................................................................................................................... 2312.1.1 When ETIP1-A PIU is used in BSC site to be connected to TCSM ETIP ....................................... 2312.1.2 When ET16 or ETS2 PIU is used in BSC site to be connected to TCSM ETIP viaEthernet over E1/T1 converter .................................................................................................................... 26

12.2 TC1C 0 and 1 .................................................................................................................................................. 2712.2.1 Move traffic from TC1C 0 and 1 cartridges .................................................................................. 2712.2.2 Delete A-interface configuration .................................................................................................. 2712.2.3 Delete TCSM/ET16/TR3/CLS from TC1C 0 and 1 cartridges ....................................................... 2712.2.4 Make cabling changes ................................................................................................................ 2812.2.5 Replace ET16 PIUs with ETIP1-A plug-in unit ............................................................................. 2912.2.6 Create first 4 TCSM units and plug-in units under TC1C-1 ........................................................... 2912.2.7 Create rest of the TCSM units to TC1C-1 and 0 .......................................................................... 3212.2.8 Create IP/PW locally to the Ater master and redundant ETIP1-A units.......................................... 3312.2.9 Add Tunnel and PW configuration of ETIP master unit for ETIP master TCSM unit inTC1C-0 track 3 ........................................................................................................................................... 3512.2.10 Create new PSN tunnel (or use the one created to Ater master) .................................................. 3612.2.11 Move traffic back to TC1C 0 and 1 cartridge ................................................................................ 39

12.3 TC1C 2 (optional) ............................................................................................................................................ 4112.3.1 Move traffic from TC1C 2 cartridge ............................................................................................. 4112.3.2 Delete A-interface configuration .................................................................................................. 4112.3.3 Delete TCSM/ET16/TR3 from TC1C 2 cartridge .......................................................................... 4112.3.4 Make cabling changes ................................................................................................................ 4212.3.5 Remove ET16 PIUs .................................................................................................................... 4212.3.6 Create the TCSM units to TC1C-2 .............................................................................................. 4212.3.7 Create IP/PW ............................................................................................................................. 4312.3.8 Move traffic back to TC1C 2 cartridge ......................................................................................... 45

12.4 TC1C 3 (optional) ............................................................................................................................................ 4712.4.1 Move traffic from TC1C 3 cartridge ............................................................................................. 4712.4.2 Delete A-interface configuration .................................................................................................. 4712.4.3 Delete TCSM/ET16/TR3 from TC1C 3 cartridge .......................................................................... 4712.4.4 Make cabling changes ................................................................................................................ 4812.4.5 Remove ET16 PIUs .................................................................................................................... 48


3 (104)

12.4.6 Create the TCSM units to TC1C-3 .............................................................................................. 4812.4.7 Create IP/PW ............................................................................................................................. 4912.4.8 Move traffic back to TC1C 3 cartridge ......................................................................................... 51

12.5 TC1C 4 (optional) ............................................................................................................................................ 5312.5.1 Move traffic from TC1C 4 cartridge ............................................................................................. 5312.5.2 Delete A-interface configuration .................................................................................................. 5312.5.3 Delete TCSM/ET16/TR3 from TC1C 4 cartridge .......................................................................... 5312.5.4 Make cabling changes ................................................................................................................ 5412.5.5 Remove ET16 PIUs .................................................................................................................... 5412.5.6 Create the TCSM units to TC1C-4 .............................................................................................. 5412.5.7 Create IP/PW ............................................................................................................................. 5512.5.8 Move traffic back to TC1C 4 cartridge ......................................................................................... 57

13 A-interface ETIP1-A implementation for IP/PWE in Standalone TCSM ................................................... 5913.1 Option1 :- ETIP with transmission redundancy TC1C1 ETIP1-A ........................................................................ 59

13.1.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C1 TCSM(s) ........................... 5913.1.2 Delete ET16 PIU(s) from TC1C1 cartridge .................................................................................. 5913.1.3 Remove cables .......................................................................................................................... 5913.1.4 Remove sync cables in case connected to TC1C1 tracks ............................................................ 6013.1.5 Add modules and new cables ..................................................................................................... 6013.1.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 6013.1.7 Synchronization usage with ETIP ................................................................................................ 6013.1.8 Create A-interface ETIP1-A plug-in unit to needed TR3 units ....................................................... 6013.1.9 Please refer APPENDIX-1 for sample creation IP/PW of TC1C-A track 17 ETIP,PSNtunnel 6113.1.10 Move traffic back to TC1C1 TCSM(s) .......................................................................................... 61

13.2 ETIP with transmission redundancy TC1C0 ETIP1-A ........................................................................................ 6213.2.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C0 TCSM(s) ........................... 6213.2.2 Delete ET16 PIU(s) from TC1C0 cartridge .................................................................................. 6213.2.3 Remove cables .......................................................................................................................... 6213.2.4 Remove sync cables in case connected to TC1C0 tracks ............................................................ 6213.2.5 Add modules and new cables ..................................................................................................... 6313.2.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 6313.2.7 Synchronization usage with ETIP ................................................................................................ 6313.2.8 Create A-interface ETIP1-A plug-in unit to needed TR3 units ....................................................... 6313.2.9 Please refer APPENDIX-1 for sample creation IP/PW of TC1C-A track 17 ETIP,PSNtunnel 6413.2.10 Move traffic back to TC1C0 TCSM(s) .......................................................................................... 64

13.3 ETIP with transmission redundancy TC1C2 ETIP1-A ........................................................................................ 6413.3.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C2 TCSM(s) ........................... 6413.3.2 Delete ET16 PIU(s) from TC1C2 cartridge .................................................................................. 6413.3.3 Remove cables .......................................................................................................................... 6413.3.4 Remove sync cables in case connected to TC1C2 tracks ............................................................ 6513.3.5 Add modules and new cables ..................................................................................................... 6513.3.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 6513.3.7 Synchronization usage with ETIP ................................................................................................ 6513.3.8 Please refer APPENDIX-1 for creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel .................... 6613.3.9 Move traffic back to TC1C2 TCSM(s) .......................................................................................... 66

13.4 ETIP with transmission redundancy TC1C3 ETIP1-A ........................................................................................ 6613.4.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C3 TCSM(s) ........................... 6613.4.2 Delete ET16 PIU(s) from TC1C3 cartridge .................................................................................. 6613.4.3 Remove cables .......................................................................................................................... 6613.4.4 Remove sync cables in case connected to TC1C3 tracks ............................................................ 6713.4.5 Add modules and new cables ..................................................................................................... 6713.4.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 6713.4.7 Synchronization usage with ETIP ................................................................................................ 6713.4.8 Create A-interface ETIP1-A plug-in unit to needed TR3 units ....................................................... 6813.4.9 Please refer APPENDIX-1 for creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel ..................... 68


4 (104)

13.4.10 Move traffic back to TC1C3 TCSM(s) .......................................................................................... 6813.5 ETIP with transmission redundancy TC1C4 ETIP1-A ........................................................................................ 68

13.5.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C4 TCSM(s) ........................... 6813.5.2 Delete ET16 PIU(s) from TC1C4 cartridge .................................................................................. 6813.5.3 Remove cables .......................................................................................................................... 6913.5.4 Remove sync cables in case connected to TC1C4 tracks ............................................................ 6913.5.5 Add modules and new cables ..................................................................................................... 7013.5.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 7013.5.7 Synchronization usage with ETIP ................................................................................................ 7013.5.8 Create A-interface ETIP1-A plug-in unit to needed TR3 units ....................................................... 7013.5.9 Please refer APPENDIX-1 for creation of IP/PW of TC1C4-A track 17 ETIP,PSN tunnel. ............. 7013.5.10 Move traffic back to TC1C4 TCSM(s) .......................................................................................... 70

13.6 Option2: ETIP HW redundancy so that TC1C1 track 17 contains ETIP1-A(Active), TC1C1 track 25contains ETIP1-A(Redundent). .................................................................................................................................... 71

13.6.1 Move traffic from TC1C1 TCSM(s) .............................................................................................. 7113.6.2 Delete ET16 PIU(s) from TC1C cartridges ................................................................................... 7113.6.3 Remove cables .......................................................................................................................... 7113.6.4 Remove sync cables in case connected to TC1C1 tracks ........................................................... 7213.6.5 Add modules and new cables ..................................................................................................... 7213.6.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 7213.6.7 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................... 7313.6.8 For IP/PWE and Tunnel creation Please refer Appendix-2 ......................................................... 7313.6.9 Move traffic back to TC1C1 TCSM(s) .......................................................................................... 73

13.7 ETIP HW redundancy so that TC1C0 track 17 contains ETIP1-A(Active), TC1C0 track 25 containsETIP1-A(Redundent). .................................................................................................................................................. 74

13.7.1 Move traffic from TC1C0 TCSM(s) .............................................................................................. 7413.7.2 Delete ET16 PIU(s) from TC1C cartridges ................................................................................... 7413.7.3 Remove cables .......................................................................................................................... 7413.7.4 Remove sync cables in case connected to TC1C0 tracks ........................................................... 7413.7.5 Add modules and new cables ..................................................................................................... 7513.7.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 7513.7.7 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................... 7513.7.8 For IP/PWE and Tunnel creation Please refer Appendix-2 ......................................................... 7613.7.9 Move traffic back to TC1C0 TCSM(s) .......................................................................................... 76


13.8.1 Move traffic from TC1C TCSM(s) ................................................................................................ 7613.8.2 Delete ET16 PIU(s) from TC1C cartridges ................................................................................... 7713.8.3 Remove cables .......................................................................................................................... 7713.8.4 Remove sync cables in case connected to TC1C2 tracks ........................................................... 7713.8.5 Add modules and new cables ..................................................................................................... 7813.8.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 7813.8.7 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................... 7813.8.8 For IP/PWE and Tunnel creation Please refer Appendix-2 ......................................................... 7913.8.9 Move traffic back to TC1C2 TCSM(s) .......................................................................................... 79




5 (104)



14 Actions after upgrade & Post conditions ................................................................................................ 8414.1 BSS Integration ............................................................................................................................................... 8414.2 BSC configuration printout (post-check) ............................................................................................................ 8414.3 Return to the old HW configuration ................................................................................................................... 85

15 Appendix 1:Sample creation of IP/PW CREATION and PW Tunnel ....................................................... 8515.1 Create IP/PW first to the TC1C1 track 17 ETIP master locally ........................................................................... 85

15.1.1 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor ................................ 8515.1.2 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor ............................................... 8615.1.3 Configure the static network routes to script file using vi –editor ................................................... 8615.1.4 Restart the ETIP master unit ....................................................................................................... 8615.1.5 Add Tunnel and PW configuration of first A-interface ETIP master unit: ........................................ 8615.1.6 Go to MML to check the D-channel state ..................................................................................... 8715.1.7 Take the A-if master TCSM unit to TE-EX ( in TC1C1 track 4) ..................................................... 8715.1.8 Connect locally to A-interface ETIP1-A master unit and upload the configuration fromETIP1-A card to TR3 card: .......................................................................................................................... 8715.1.9 Take the A-interface master TCSM unit to WO-EX ...................................................................... 87

15.2 Create new PSN tunnel (or use the one created to A-interface master) .............................................................. 8715.2.1 Create new PW inside PSN tunnel .............................................................................................. 8815.2.2 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE) .......................... 8815.2.3 Verify information ...................................................................................................................... 89

16 Appendix 2:Sample creation of IP/PWE and Tunnel for ETIP as A-if TCSM. .......................................... 9016.1 Create IP/PW locally to the A-interface master and redundant ETIP1-A units ..................................................... 90

16.1.1 Configure locally the first PW interface to ETIP1-A in TC1C0 in track 17 by using localcable 9016.1.2 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor ................................ 9016.1.3 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor ............................................... 9016.1.4 Configure the static network routes to script file using vi –editor ................................................... 9116.1.5 Restart the ETIP master unit ....................................................................................................... 9116.1.6 Configure locally the redundant ETIP1-A unit for Ater interface PW by using local cableconnection in ETIP1-A card in TC1C0 in track 25 ........................................................................................ 9116.1.7 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor ................................ 9116.1.8 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor ............................................... 9216.1.9 Configure the static network routes to script file using vi –editor ................................................... 9216.1.10 Restart the ETIP master unit ....................................................................................................... 92

16.2 Add Tunnel and PW configuration of first A-interface ETIP master unit (TC1C0 in track 17) ................................ 9216.2.1 Go to MML to check the D-channel state ..................................................................................... 9316.2.2 Take the A-if master TCSM unit to TE-EX (in TC1C0 track 4) ...................................................... 9316.2.3 Connect locally to A-interface ETIP1-A master unit and upload the configuration fromETIP1-A card to TR3 card: .......................................................................................................................... 9316.2.4 Take the A-interface master TCSM unit to WO-EX ...................................................................... 93

16.3 Create new PSN tunnel (or use the one created to A-interface master) .............................................................. 9316.3.1 Create new PW inside PSN tunnel .............................................................................................. 9416.3.2 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE) .......................... 9516.3.3 Verify information ...................................................................................................................... 95

17 Appendix 3: Internal PCM usage for A-interface .................................................................................... 96


6 (104)

18 Appendix 4:Internal PCM Usage for A-ter interface ............................................................................... 9919 Appendix 5: Updating embedded software of ETIP1-A ......................................................................... 102

Contact:

Contact your local Nokia Solutions and Networks support

Summary of changes:

1.0-0 1st approved version


7 (104)

1 PURPOSE

This document describes the implementation of changing ET16 plug-in unit in standalonen TCSM3i to ETIP1-Aline/equipment protection.The ETIP1-A line/equipment protection implementation is available for third generation DX200 standaloneTCSM3i.


8 (104)

2 SCOPE OF APPLICATIONS

The standalone TCSM ETIP1-A implementation for IP/PWE is available for third generation DX200 TCSM3i inS16 onwards release level.The procedure cannot be executed without traffic interruption. Traffic must be moved from concerning ET16/TR3plug-in unit before the actual upgrade.Procedure must be performed locally at BSC/TCSM3i site.


9 (104)

3 USING THE DOCUMENT

3.1 General info

The standalone TCSM3i ETIP1-A implementation for IP/PWE is done manually withouth the HIT macro.


10 (104)

4 INTRODUCTION

The Standalone TCSM3i ETIP1-A implementation for IP/PWE procedure consists of the following tasks:

- Fallback copying of the current software- BSC configuration printout (pre-check)- Licence installation and feature activation- Ater interface ETIP1-A implementation for IP/PWE in Standalone TCSM- A-interface ETIP1-A implementation for IP/PWE in Standalone TCSM- Actions after upgrade and post conditions

o BSS Integrationo BSC configuration printout (post-check)

Fallback copying, BSC configuration printout tasks can be executed during daytime.Actual upgrade is recommended to be executed during night-time. This procedure can be done to standaloneTCSM3i.For standalone TCSM3i part, the procedure is devided for A- and Ater-interfaces. For Ater-interface only HWredundancy option is possible. A-interface contains more options: transmission redundancy, HW redundancy andmixed configuration. In case when old configuration needs to be removed, the traffic must be moved, interface(s) removed becausethe plug-in unit needs to be deleted from equipment database. After successful upgrade and interfaces has beencreated back, the traffic can be moved backThe estimated time for HW upgrade depends on the configuration.The upgrade cannot be executed with traffic and traffic needs to be re-hosted. During upgrade effected unit(s) willbe blocked and state changed to TE-EX or SE-NH.

With this procedure following possibility is to be added:- In Standalone TCSM3i Ater- interface part, replace ET16 with ETIP plug-in unit with hardware

redundancy- In Standalone TCSM3i A- interface part, replace ET16 with ETIP plug-in unit with line or hardware

redundancy and also mixed configuration option is possible.

Background:ETIP1-A plug-in unit is a unit, which implements IETF pseudo wire emulation edge to edge (PWE3) functionalityin DX 200. Basically this means E1/T1 over Ethernet. The ETIP1-A plug-in unit has one redundant Gigabitethernet interface in front panel.The Gigabit ethernet interfaces are provided by hot-pluggable SFP modules, which are not part of the ETIP1-APIU’s structure.As a GSW interface the unit uses either thirty-two 8 Mbit/s TDM interfaces or two Hotlink interfaces. There areactually four physical Hotlink interfaces, due to 2N redundancy support.Working Ater ETIP1-A plug-in unit is equipped on TC1C 0 cartridge and protecting Ater ETIP1-A plug-in unit isequipped on TC1C 1 cartridge.

Working and protecting A-interface ETIP1-A plug-in units are in different cartridge sections (working ETIP1-A inthe first TC1C section and protecting ETIP1-A in the second TC1C section) & powered by different PDFUs. Onlythe 1st PWE interface (i.e. EET) from the ETIP1-A plug-in units is used in equipment protection.

ETIP in TCSM3i: Can be connected to max 30 BSC3i’s Can have one ETIP1-A pair in ATER interface and max three ETIP1-A’s in A interface. Ater ETIP must be HW redundant, but A interface can be line redundant. Ater ETIP capacity is 96 PCMs and A ETIP capacity is 128 PCMs.

Internal PCM numbering starting from 0. Not same order as physical TR3E/A/T cards in cabinet!


11 (104)

4.1 Standalone TCSM3i equipment after upgrade

Configuration after HW upgrade in case of HW redundancy:

Figure-1 ETIP1-A Exchange Terminal plug-in units used as Ater interfaces inTC1C 0 & 1 (TC1C-A cartridges). Optional PIUs turquoise/dark.

Figure-2. ETIP1-A Exchange Terminal plug-in units used as Ater interfacesin TC1C 2 … 4 (TC1C-A cartridges). Optional PIUs turquoise/dark.


12 (104)

4.1.1 A and Ater interface ETIP with full HW redundancy

Congifuration after HW upgrade in case of HW redundancy:

ETIP1-A Exchange Terminal plug-in units used as Ater interfaces in TC1C 0 &1 (TC1C-A cartridges). Optional PIUs turquoise/dark.

ETIP1-A Exchange Terminal plug-in units used as Ater interfaces in TC1C 2 …4 (TC1C-A cartridges). Optional PIUs turquoise/dark.


13 (104)

4.1.2 A interface ETIP Mixed configurations

In TCSM3i for standalone TCSM installation new delivery mixed ET16 and ETIP1_A andETP-A configuration is possible in A-if inside the cabinet (not inside TC1Ccatridge).Concerning Ater interface either ET16 or ETIP1_A can be used.

5 PRE-REQUIREMENTS

5.1 Pre-requirements & Actions needed prior upgrade

The procedure can be implemented only for S16 or onwards software. It is recommended to install all availablechange deliveries prior to the upgrade.SW licence 1380 (Integrated IP Card) is needed to be installed before actual upgrade can be started.

In case of Standalone TCSM3i part, the related ET16/ plug-in unit in BSC side, needs to be upgraded beforeTCSM3i upgrade can be started.

IMPORTANT!Re-direct traffic from upgraded TCSA cabinet. Each ETIP unit mustbe handled case by case and PCM areas which are affected duringupgrade may vary. In case upgrade causes disturbances to someother unit, the traffic needs to be re-directed, interfaces removedand unit needs to be deleted (PCM areas released to new ETIP unitusage) from hardware database before new configuration iscreated.

BSS Split tool offers automated process to support BSC renewal. This isextremely useful, when older BSC(s) are modernised to BSC3i(s). Thisprocess includes the automation of labor-intensive re-hosting of BTS tonew BSC(s) including data and parameter updates to name a few. Thedowntime of operational BTS(s) is this way minimised during re-homing.If re-homing speed is the key driver, more than 100 sites can be movedto the new BSC during one night by using .XML files for data transferbetween the BSC(s) assisted by CM tools (CM Plan Manager, CM Editorand CM Analyser). Further information about BSS Split tools is availablefrom Nokia OSS / NetAct representatives.

5.2 Restrictions

In Standalone TCSM3i Ater interface part:TC1C-0 and TC1C-1 cartridges are required to be upgrade. After that the other TC1C-cartridge upgrades areoptional.

During upgrade, the unit will be blocked, meaning that the interfaces which controlling unit is upgradedwill be affected. After the upgrade has been finished successfully for one ETIP unit (in case of HWredundancy ETIP unit pair) the traffic can be re-directed back.


14 (104)

5.3 Needed documentation

To perform the upgrade successfully, the following documentation is required:Standalone TCSM3i ETIP1-A implementation for IP/PWE (thisdocument)

BSC3i with S16 level or onwards software and hardware.

TC1C-A cartridge equipped using ET16 plug-in units which support4 D channel ET16 in TCSM. It should also be noted that the oldstyle plug-in units which support one D channel to ET16 in TCSMare also supported when using them in the logical cassette.

Standalone TCSM3i using mixed E1/T1, ETP and PWE3connectivity media in the TC1C-A cartridge.

Plug-in unit software upgrade procedure

Cabling Instructions for TCSM3i (NED)

Equipment list for TCSM3i (NED)

PWT User Guide (NED)

Fallback copying instructions of DX200 BSC for S16 (NED)

HIT Users manual

Cabling Instructions for i-series Network Elements

5.4 Needed equipment

To perform the upgrade successfully, the following HW are required:In case of Standalone TCSM3i Ater interface: General Set for

ETIP1-A used as Ater Interface in Standalone TCSM3i installation

(S15) and Cabinet upgrade set, ETIP1-A redundancy pair specific for

Standalone TCSM3i installation (S15).

In case of Standalone TCSM3i A interface: Cabinet upgrade set,

ETIP1-A redundancy pair specific for Standalone TCSM3i installation

(S15)..

Needed amount of ETIP plug-in units.

The status of the current BSC software package is checked. Note that the current software packagemust be with status BU before the actual upgrade can be started. The software status is to bechecked with command:

ZWQO:RUN;


15 (104)

Check from the output that all the computer units which are currently in use are running on correctsoftware package with the status BU. If the software package status is FB or NW, find out the causefor the setting.

The status can be changed to BU with command:

ZWSC:STAT=NW:STAT=BU;

The active and blocked alarms (DX200 and BTS alarms) can be printed out with followingcommands:

ZAHO;

ZABO;

ZEOL;

ZEOE;

6 FALLBACK COPYING OF THE CURRENT PACKAGE

A fallback copying of the running software package must be made before the upgrade.A fallback copying from the old SW can be made by running macro step ‘Fallback copying of the currentpackage’.Manually, the fallback copying can be made following the document: Fallback copying in BSC. The documentcan be found from NED.

7 BSC CONFIGURATION PRINTOUT (PRE-CHECK)

The information about the BSC configurations and conditions are collected.Precondition checking is recommended to do during the daytime before the actual upgrade will be started. Thechecking can be made by using the macro (UPGMAIN.HIT) or manually following the instructions from “BSCconfiguration printout”-document delivered in Release Binder.For macro execution, choose the BSC configuration printout (pre) step in BSC ETIP1-A implementation forIP/PWE procedure. Follow then the macro execution according the BSC configuration printout –document.

8 LICENCE INSTALLATION AND FEATURE ACTIVATION

SW licence 1380 (Integrated IP Card) is needed to be installed before actual upgrade can be started.Macro checks the licence status and if licence is not installed properly the licence needs to be installed manuallyaccording to following instructions.

Licence state can be printed with following command:ZW7I:FEA,FULL:FSTATE=ON,FEA=1380;

FlexiBSC KOLI 542257 2010-04-15 14:13:13

FEATURE INFORMATION:

----------------------------------------------FEATURE CODE:..............1380FEATURE NAME:..............ETIPFEATURE STATE:.............ON

FEATURE CAPACITY:..........25


16 (104)

COMMAND EXECUTEDIf licence state is OFF, change the state to ON with following command:ZW7M:FEA=1380:ON:;

If licence is not installed, install the new licence file with the command:ZW7L:<licence_file_name>:ON;More information of licences in the BSC can be found in NED.


17 (104)

9 CONFIGURATION EXAMPLE OF ATER INTERFACE USED IN THIS INSTRUCTION

Here is the example configuration used in these instructions for Standalone TCSM3i Ater interface.In Thisexample the BSC and TCSM has ETIP1-A card created and connection via Cisco router. In this document inexample the TCSM ETIP1-A in Ater interface is connected via cisco router to BSC ETIP1-A card

HSRP:VLAN150 10.16.65.161VLAN151 10.16.65.169VLAN152 10.16.65.177VLAN153 10.16.65.185

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.181/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.181/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.180/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.180/29VLAN152

PWMANA0ETIP,1

TCSM3i

ETIP connectionKOLI – TCSM3i

ETIP connectionKOLI – TCSM3i

Cisco SITE1_0

Cisco SITE1_1

Gi1/0/17

Gi1/0/17

Gi1/0/18

Gi1/0/18

EET4

EET5

Transmission protected Hardware protected

KOLIKOLI TCSM3iTCSM3i


18 (104)

10 MASTER UNITS IN TCSM SITE

For TC1C1 Catridge


19 (104)

TC1C-A 1/1-shelf cartridgeSlot Name Function Equip. # of 1,5

Mbit/s /2Mbit/s(Ater)

# of 1,5Mbit/s /2Mbit/s (Ainterface)

Note

F1 TR3T Transcoder piu Base 1 4 2); O&M master for Ainterface ET16 (handlingTR3Ts in slots 1…4) and forthe Ater ET16 (slot 13)

F2 TR3T Transcoder piu Base 1 4 Cabinet "Headmaster" TR3TF3 TR3T Transcoder piu Base 1 4 Ater ETIP master TR3T slots

1…4F4 TR3T Transcoder piu Base 1 4 A interface ETIP master TR3T

slots 1…4; A-interface ETP-Amaster TR3T slots 1…4

F5 TR3T Transcoder piu Base 1 4 2); O&M master for the Ainterface ET16 (handlingTR3Ts in slots 5…8)

F6 TR3T Transcoder piu Base 1 4

F7 TR3T Transcoder piu Base 1 4 Ater ETIP master TR3T slots5…8

F8 TR3T Transcoder piu Base 1 4 A interface ETIP master TR3Tslots 5…8; A interface ETP-Amaster TR3T slots 5…8

F9 SHIM16T /TR3T

Front panel with shim plate /Transcoder piu

Base /Optional 1 4

1); 2); O&M master for the Ainterface ET16 (handlingTR3Ts in slots 9…12)

F10 SHIM16T /TR3T


Base /Optional 1 4 1)

F11 SHIM16T /TR3T


Base /Optional 1 4

1); Ater ETIP master TR3Tslots 9…12

F12 SHIM16T /TR3T


Base /Optional 1 4

1); A interface ETIP masterTR3T slots 9…12; A interfaceETP-A master TR3T slots9…12

F28 SHIM16T /TR3T


Base /Optional 1 4

1); 2); O&M master for the Ainterface ET16 (handlingTR3Ts in slots 28…31) and forthe Ater ET16 (slot 23)

F29 SHIM16T /TR3T



F30 SHIM16T /TR3T


Base /Optional 1 4


F31 SHIM16T /TR3T


Base /Optional 1 4


F32 SHIM16T /TR3T


Base /Optional 1 4


F33 SHIM16T /TR3T



F34 SHIM16T /TR3T


Base /Optional 1 4


F35 SHIM16T /TR3T


Base /Optional 1 4

1); A interface ETIP masterTR3T slots 32…35; A-interface ETP-A master TR3Tslots 32…35

F36 SHIM16T /TR3T


Base /Optional 1 4



20 (104)




Note

F37 SHIM16T /TR3T



F38 SHIM16T /TR3T


Base /Optional 1 4


F39 SHIM16T /TR3T


Base /Optional 1 4


1) If no TR3T is equipped, SHIM16T (this shim plate covers four slots)is left equipped.

2) 4* TR3T is the minimum amount of TR3T plug-in units that can beshared among one BSC.

3) The TR3T plug-in units have to be equipped from the secondcartridge because cabinet "Headmaster" TR3T is in slot 02 of TC1C1.

A. TC1C 0 and 2…4 (TC1C-A cartridge)


21 (104)




Note

F1 SHIM16T /TR3T


Base /Optional 1 4

1); 2); O&M master for Ainterface ET16 (handlingTR3Ts in slots 1…4) and forthe Ater ET16 (slot 13)

F2 SHIM16T /TR3T



F3 SHIM16T /TR3T


Base /Optional 1 4


F4 SHIM16T /TR3T


Base /Optional 1 4


F5 SHIM16T /TR3T


Base /Optional 1 4


F6 SHIM16T /TR3T



F7 SHIM16T /TR3T


Base /Optional 1 4


F8 SHIM16T /TR3T


Base /Optional 1 4


F9 SHIM16T /TR3T


Base /Optional 1 4


F10 SHIM16T /TR3T



F11 SHIM16T /TR3T

Front panel with shim plate /Transcoder piu (ETSI)

Base /Optional 1 4


F12 SHIM16T /TR3T

Front panel with shim plate /Transcoder piu (ETSI)

Base /Optional 1 4


F28 SHIM16T /TR3T


Base /Optional 1 4

1); 2); O&M master for the Ainterface ET16 (handlingTR3Ts in slots 28…31) and forthe Ater ET16 (slot 23)

F29 SHIM16T /TR3T


Base /Optiona 1 4 1)

F30 SHIM16T /TR3T


Base /Optional 1 4


F31 SHIM16T /TR3T


Base /Optiona 1 4


F32 SHIM16T /TR3T


Base /Optional 1 4


F33 SHIM16T /TR3T



F34 SHIM16T /TR3T


Base /Optional 1 4


F35 SHIM16T /TR3T


Base /Optional 1 4



22 (104)




Note

F36 SHIM16T /TR3T


Base /Optional 1 4


F37 SHIM16T /TR3T



F38 SHIM16T /TR3T


Base /Optional 1 4


F39 SHIM16T /TR3T


Base /Optional 1 4


1) If no TR3T is equipped, SHIM16T (this shim plate covers four slots)is left equipped.

2) 4*TR3T is the minimum amount of TR3T plug-in units that can beshared among one BSC.

11 TCSA RACK CARTRIDGE POSITION INFO

Alarm groups in TCSA cabinet

HW Cabinet and Catridge CreationZWTC:TC1C_A,1X1-19;//clockZWTC:TC1C_A,1X2-19;//clockZWTJ:TCSA_B,1X:AL=1X1-19-1,PDFU=2;//cabinet creationZWTC:FTRB_A,1X21-0,:AL=1X1-19-15,;//fan unit creationZWTC:TC1C_A,1X1-0,:AL=1X1-19-2,;//first shelf left side


23 (104)

ZWTC:TC1C_A,1X1-22,:AL=1X1-19-3,;//first shelf right sideZWTC:TC1C_A,1X2-0,:AL=1X1-19-4,;//second shelf left sideZWTC:TC1C_A,1X2-22,:AL=1X1-19-5,;//second shelf right sideZWTC:TC1C_A,1X3-0,:AL=1X1-19-6,;//Third shelf left side

ZWTC:TC1C_A,1X3-22,:AL=1X1-19-7,;//Third shelf right sideZWTC:TC1C_A,1X4-0,:AL=1X1-19-8,;// Fourth shelf left sideZWTC:TC1C_A,1X4-22,:AL=1X1-19-9,;//Fourth shelf right sideZWTC:TC1C_A,1X5-0,:AL=1X1-19-10,;//Fifth shelf left sideZWTC:TC1C_A,1X5-22,:AL=1X1-19-11,;//Fifth shelf right side

NOTE:-Here “X” may be A,B,C,D…etc.

12 ATER INTERFACE ETIP1-A IMPLEMENTATION FOR IP/PWE IN STANDALONETCSM

This chapter includes the instructions how to install ETIP1-A plug-in unit used as Ater Interface in StandaloneTCSM3i installation.

ETIP1-A SW update instructions can be found in the end in Appendix 3:Updating embedded software of ETIP1-A

ETIP1-A internal PCM mapping in A- and Ater interface can be found in Appendix 1: Internal PCM usagefor Ater interface and Appendix 2: Internal PCM usage for A- interface

Note!Only HW redundancy is possible in Ater interface in Standalone TCSM3i with ETIP1-A equipment.

At least TCSM3i cabinet’s TC1C-0 and TC1C-1 cartridges MUST be upgraded. TC1C-2 – TC1C-4 upgrades areoptional.

There is several options in physical Ater connection between the BSC and TCSM in case ETIP1-A in use inTCSM site:

- TCSM ETIP1-A card connected via router to BSC ETIP1-A card

- example TCSM ETIP1-A card connected to Atrica-A2200 where it’s going out toBSC site as E1or T1

In this document examples the Ater configuration is done by connecting the TCSM ETIP1-A card viaCisco router to BSC ETIP1-A card.Note! When ET16 is used in Standalone TCSM A-i/f there are two options for the cabling:1. with Cabling Cabinet: CPSM cables + PCMC8A connector (connector position 2M behind slot where ET16 isequipped)2. without Cabling Cabinet: RCM16 module (behind slot where ET16 is equipped) + 2 CMDE cables (to cross-connection)

12.1 Ater plug-in unit installation to BSC

12.1.1 When ETIP1-A PIU is used in BSC site to be connected to TCSM ETIP

12.1.1.1 Configure the PW_MANA0 and PW0 for the BSC ETIP1-A card

ZQRA:<unit type>,<unit index>::<interface name>,<VLAN vid>,<physicalinterface>;


24 (104)

Example:ZQRA:ETIP,2::PW0:;ZQRA:ETIP,2::PW_MANA0;ZQRA:ETIP,2::VLAN150,150,PW_MANA0,:;ZQRA:ETIP,2::VLAN151,151,PW0,::;

12.1.1.2 Configure the IP address for VLAN’s

ZQRN:<unit type>,<unit index>::<interface name>,:<IP address>,<netmasklength>,<IP address type P,<attribute V>::;

example:ZQRN:ETIP,2::VLAN150,:"10.16.65.164",29,P,;ZQRN:ETIP,2::VLAN151,:"10.16.65.172",29,P,V::;

12.1.1.3 Create the static routes

ZQKC:<unit type>,<unit index>::<destination IP address>,<netmasklength>:<gateway IP address>:PHY;

ZQKC:ETIP,2::"10.16.65.184",29:"10.16.65.169":PHY;ZQKC:ETIP,2::"10.16.65.176",29:"10.16.65.161":PHY;

12.1.1.4 Create new PSN tunnel

Use the QYA MML command to create a new PSN tunnel.ZQYA:<unit type>,<unit index>,<interface type>:<tunnel index>:<dst IPaddress>:<tunnel name>;

Name Value Info

unit type

Type of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i and TCSM forETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)

tunnel index 0-65534Numerical identifier for PSN tunnel (Obligatory, must beunique at least inside one ETIP1-A

dst IP address Destination IP address of tunnel (Obligatory)

tunnel nameName for PSN tunnel (Optional, default value is “”, maxlength 20)

Example:ZQYA:ETIP,2:322:"10.16.65.188":ATERTOTCSM322:;

12.1.1.5 Create new PW inside PSN tunnel

Use the QYC MML command to create a new PW inside the PSN tunnel.ZQYC:<unit type>,<unit index>:<PW index>: <tunnel index>:<local UDPport>,<peer UDP port>:<PCM number>:<tsl mapping>:<JB length>:<number offrames>:<ToS field>:<VLAN priority>:<PW name>;


25 (104)

Name Value Info

unit typeType of configured unit Type of configured unit (Obligatory, ETIP forETIPs in BSC3i and TCSM for ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)

PW 0-65534Numerical identifier for PW (Obligatory, must be unique at leastinside one ETIP1-A (Obligatory)

tunnel index 0-65534Numerical identifier of the tunnel in where this PW is included(Obligatory)

local UDP port 1-65535 Number of local UDP port (Obligatory)peer UDP port Number of peer UDP port (Obligatory)

PCM number

0-8191(ETIP)0-127(TCSM) PCM line number (Obligatory)

tsl mapping 1-31 List of timeslots(Optional, default is timeslots 1-31)

JB lenght 1-192

Jitter Buffer length in frames, settable by one frame (125us) steps(Optional, default value is 40 (+/-5ms), range from 1 (+/-125us ) to192 (+/-24ms))

number of frames 1-40Number of collected TDM frames per Ethernet packet (Optional,default is 8)

ToS field 0-63 IP packet ToS field (same as DSCP) (Optional, default is 0)

VLAN priority 0-7

VLAN priority (Optional, if does not set value from IP management isused instead, if there is no VLAN set in IP management thisparameter will be ignored)

PW name Name for PW (Optional, default value is “”, max length 20)

Example:ZQYC:ETIP,2:322:322:202,202:322:::::::TCSM322:;ZQYC:ETIP,2:320:322:200,200:320::::::TCSM320:;ZQYC:ETIP,2:321:322:201,201:321::::::TCSM321:;

12.1.1.6 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)

Use the QYJ MML command to enable all the PWs in a tunnel.ZQYJ:ETIP,<unit index>: <tunnel index>:<action>;

Name Value Info

unit type

Type of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i and TCSMfor ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)tunnel index 0-65534 Numerical identifier for PSN tunnel (Obligatory)action ENA/DIS Action to perform (Obligatory)Example:


26 (104)

ZQYJ:ETIP,2:322:ENA;

Enable single PW traffic inside PSN tunnel

ZQYE:<unit type>,<unit index>:<PW index>:<action>;

Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:ETIP,2:320:ENA:;ZQYE:ETIP,2:321:ENA:;

12.1.1.7 Verify information

ZQYI:<unit type>,<unit index>:<TUNNEL=<tunnel index>,<PW=<PWindex>>,<PCM=<PCM number>;ZQYS:<unit type>,<unit index>:<TUNNEL=<tunnel index>,<PW=<PWindex>,PCM=<PCM number>;

Name Value Info

unit type

Type of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i andTCSM for ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)tunnel index 0-65534 Numerical identifier for PSN tunne (Obligatory)PW index 0-65534 Numerical identifier for PW (Optional)

PCM number0-8191(ETIP)0-127 (TCSM)

Number of inquired PCM (Optional, range inETIP 0 - 8191 and in TCSM 0 - 127)

12.1.2 When ET16 or ETS2 PIU is used in BSC site to be connected to TCSM ETIP via Ethernet overE1/T1 converter

Example Atrica A-2200Connect in BSC site the ET16 or ETS2 normally for A-interface usage as informed in NED BSS integrationmanual.


27 (104)

12.2 TC1C 0 and 1

12.2.1 Move traffic from TC1C 0 and 1 cartridges

Move traffic from TC1C 0 and 1 cartridges.

12.2.2 Delete A-interface configuration

Related A-interface configuration needs to be deleted manually from related ET(s). More instruction can be foundfrom NED document Creating and managing BSC configuration.

Inactivate the A-interface links affected to TC1C-0 and 1 TCSM’s.

12.2.2.1 Change the affected links state

ZNLC:<link_number>:INA;

12.2.2.2 Deny link activation

ZNLD:<link_number>;

12.2.2.3 Change the TCSM unit to SE-NH state

ZUSC :TCSM,<index>:BL;ZUSC :TCSM,<index>:TE;ZUSC :TCSM,<index>:SE;ZUSC :TCSM,<index>:SE;

12.2.2.4 Change the speech channels to NU state

ZCEC:<et_pcm>,<crct>:BL;ZCEC:<et_pcm>,<crct>:NU;

12.2.2.5 Delete speech channels

ZRCR:<cgr>,<et_pcm>,<crct>;

12.2.2.6 Remove through connected channel

ZWGR:<et_pcm-tsl>:<tc_pcm-tsl>;

12.2.2.7 Delete transcoder PCM

ZWGD::<et_pcm>,<tc_pcm>;

12.2.2.8 Disconnect TCSM TR3E/TR3A/TR3T units

ZWUD:TCSM,<unit>:<piu type>,<index>;

12.2.3 Delete TCSM/ET16/TR3/CLS from TC1C 0 and 1 cartridges

Delete Ater TCSM(s) and ET16 /TR3/CLS unit equipments from TC1C-0and 1 with following commands:

ZWTQ:TCSM,<index>,<location>:<piu type>,<index>;ZWTV:TCSM,<index>,<location>;


28 (104)

Note that the location coordinates are needed if two or more plug-inunits are configured to TCSM.

12.2.4 Make cabling changes

In this step, ET16 plug-in unit cables are disconnected.Remove cablings from TC1C-0 and 1 cartridge according to following table:Equipping CABLE FROM CABLE TO

No FU Position Cabinet Panel Position Type Use NoteTCSA_150 TC1C 0 1.0B 13.1A IC203-A CPETS-F 00B 00 CPSM015 ET ATER Interface externalTCSA_151 TC1C 0 1.0B 13.1J IC203-A CPETS-F 00B 01 CPSM016 ET ATER Interface externalTCSA_152 TC1C 0 1.0B 13.1R IC203-A CPETS-F 00B 02 CPSM014 ET ATER Interface externalTCSA_153 TC1C 0 1.0B 23.1A IC203-A CPETS-F 00B 03 CPSM013 ET ATER Interface externalTCSA_154 TC1C 0 1.0B 23.1J IC203-A CPETS-F 00B 04 CPSM012 ET ATER Interface externalTCSA_155 TC1C 0 1.0B 23.1R IC203-A CPETS-F 00B 05 CPSM013 ET ATER Interface externalTCSA_156 TC1C 1 2.0B 13.1A IC203-A CPETS-F 00B 06 CPSM018 ET ATER Interface externalTCSA_157 TC1C 1 2.0B 13.1J IC203-A CPETS-F 00B 07 CPSM019 ET ATER Interface externalTCSA_158 TC1C 1 2.0B 13.1R IC203-A CPETS-F 00B 08 CPSM018 ET ATER Interface externalTCSA_159 TC1C 1 2.0B 23.1A IC203-A CPETS-F 00B 09 CPSM017 ET ATER Interface externalTCSA_160 TC1C 1 2.0B 23.1J IC203-A CPETS-F 00B 10 CPSM016 ET ATER Interface externalTCSA_161 TC1C 1 2.0B 23.1R IC203-A CPETS-F 00B 11 CPSM017 ET ATER Interface external

Remove locking pegs from tracks 12 & 13 tracks and add to needed positionsThis set is needed when ETIP1-A is used as Ater interface. Ater ETIP1-A isalways equipment protected.

HW product full name HW Product AmountIntermediate cable CHFX 5 pcsIntermediate cable CHES 5 pcs

*) Lengths of these cables according to the worst case. CHFX &CHES cables are cabled between the ETIP1-A plug-in units in aprotection pair and CHQ & CHG cables are cabled between RearConnector Module on the back of working ETIP-A and the back ofprotecting ETIP1-A.

Terminators and Setting modulesPart List includes only one Rear Connector Module RCOM-A + one ADMOD15 Module,corresponding to upgrade kit for 1 protection pair (up to five upgrade kits can be equipped perTCSA cabinet (1 per cartridge).

Note:- 1 pc ADMOD07 connected to the back / connector position 1.0B 13.4E of active Ater ETIP1-A in TC1C 0

Position ID Name FU Use Note

HW product full name HW Product AmountRear Connector Module for ETIP1-A RCOM-A 1 pcSetting module ADMOD15 1 pcIntermediate cable CHFX 1 pc *)Intermediate cable CHES 1 pc *)Intermediate cable CHQ 3 pcs *)Intermediate cable CHG 1 pc *)


29 (104)

Position ID Name FU Use Note1.0B

13.1A C111289 RCOM-A TC1C0

Rear Connector Module forETIP1-A 1 pc

1.0B13.4E C108694 ADMOD07 TC1C

0 Setting module for Active ETIP1-A 1 pc

2.0B13.4E C108702 ADMOD15 TC1C

1Setting module for protected

ETIP1-A 1 pc

Intracabinet cables

Equipping CABLE FROM CABLE TONo FU Position FU Position Type Use Note

TCSA_600 TC1C 0 1.0B 13.1A TC1C 0 1.0B 18.1A CHFX007 PCMTCSA_601 TC1C 0 1.0B 13.1E TC1C 0 1.0B 18.1E CHES008 PCMTCSA_602 TC1C 0 1.0B 13.1G TC1C 1 2.0B 18.1A CHFX015 PCMTCSA_603 TC1C 0 1.0B 13.1L TC1C 1 2.0B 18.1E CHES018 PCMTCSA_604 TC1C 0 1.0B 13.1N TC1C 2 3.0B 18.1A CHFX020 PCMTCSA_605 TC1C 0 1.0B 13.1R TC1C 2 3.0B 18.1E CHES024 PCMTCSA_606 TC1C 0 1.0B 13.1T TC1C 3 4.0B 18.1A CHFX023 PCMTCSA_607 TC1C 0 1.0B 13.1X TC1C 3 4.0B 18.1E CHES026 PCMTCSA_608 TC1C 0 1.0B 13.1Z TC1C 4 5.0B 18.1A CHFX025 PCMTCSA_609 TC1C 0 1.0B 13.2D TC1C 4 5.0B 18.1E CHES028 PCM

TCSA_610 TC1C 0 1.0B 13.4A TC1C 1 2.0B 13.4A CHFX015 2NTCSA_611 TC1C 0 1.0B 13.4G TC1C 1 2.0B 13.4G CHES011 2N

TCSA_612 TC1C 0 1.0B 12.1A TC1C 1 2.0B 13.1A CHQ014 PCMTCSA_613 TC1C 0 1.0B 12.1J TC1C 1 2.0B 13.1J CHQ014 PCMTCSA_614 TC1C 0 1.0B 12.1R TC1C 1 2.0B 13.1R CHQ015 PCMTCSA_615 TC1C 0 1.0B 12.1Z TC1C 1 2.0B 13.1Z CHG015 PCM

12.2.5 Replace ET16 PIUs with ETIP1-A plug-in unit

Remove ET16 plug-in units from TC1C 0 and 1 cartridge track 13 .

Install ETIP1-A plug-in unit to TC1C 0 track 13 and install redundantETIP1-A plug-in unit to TC1C 1 track 13.

Rule for TCSM creation is that 4 TR3 units must be at same BSC, so create first 4 units under one BSC

12.2.6 Create first 4 TCSM units and plug-in units under TC1C-1

12.2.6.1 Create theTC1C1 track 1 TCSM unit and plug-in unitsTwo options a) when ET16 is used for A-interface and b) whenETIP1-A used for A-interface ( in case A-interface upgraded earlierfor ETIP1-A)

a. TCSM unit when ET16 in use (A-interface ET master)ZWTU:TCSM, <ater_pcm>:1x2-0; /TCSM unit in TC1C1


30 (104)

ZWTP:TCSM,<ater_pcm>:<TR3_type>,0,1::GENERAL,8,<ater_pcm>,TSL,1::;

ZWTP:TCSM,<ater_pcm>,1x2-0:ET16,0,14,:::;// /ET unit for TCSM

ZWGC:<ater_pcm>,<tc_pcm_line>:POOL=<pool_id>:BCSU,<index>:;ZWUC:TCSM,<ater_pcm>:<TR3_type>,0;

b. TCSM unit when ETIP1-A used for A-interface ( in case A-interface upgraded earlier for ETIP1-A)

ZWTU:TCSM, <ater_pcm>:1x2-0;ZWTP:TCSM,<ater_pcm>:1x2-0:<TR3_type>,0,1::GENERAL,8,<ater_pcm>,TSL,1::;

Create TCSM pool and connect the unitZWGC:<ater_pcm>,<tc_pcm_line>:POOL=<pool_id>:BCSU,<index>:;ZWUC:TCSM,<ater_pcm>:<TR3_type>,0;

12.2.6.2 Create the TC1C1 track 2 TCSM units and plug-in units (Clock master)

Create TCSM unitsZWTU:TCSM,<ater_pcm>:1x2-0; /TCSM units in TC1C1ZWTP:TCSM,<ater_pcm>:<TR3_type>,0,2,::GENERAL,8,<ater_pcm>,TSL,1::;

ZWTU:TCSM,<ater_pcm>:1x1-0:; /Clock unit locationZWTU:TCSM,<ater_pcm>:1x2-0:; / Clock unit locationZWTP:TCSM,<ater_pxm>,1x1-0:CL3TG,0,19:;ZWTP:TCSM,<ater_pcm>,1x2-0:CL3TG,1,19:;

Create TCSM pool and connect the unitZWGC:<ater_pcm>,<tc_pcm_line>:POOL=<pool_id>:BCSU,<index>:;ZWUC:TCSM,<ater_pcm>:<TR3_type>,0;

12.2.6.3 Create the TC1C1 track 3 TCSM units and plug-in units (Ater-interface ETIP master)

ETIP master and redundant TCSM unitsZWTU:TCSM,<ater_pcm>:1x1-0; // master ETIP TCSM units in TC1C1ZWTU:TCSM,<ater_pcm>:1x2-0:; // Redundant ETIP TCSM unit

Create Plug in units under TCSM unitZWTP:TCSM,<ater_pcm>:1x2-0:<TR3_type>,0,3,::GENERAL,8,<ater_pcm>,TSL,1::;ZWTP:TCSM,<ater_pcm>,1x1-0:ETIP1_A,0,13,:::;ZWTP:TCSM,<ater_pcm>,1x2-0:ETIP1_A,1,13,:::;

Create TCSM pool and connect the unitZWGS:<ater_pcm>:< number of through connected channels>:;


31 (104)

ZWGC:<ater_pcm>,<tc_pcm_line>:POOL=<pool_id>:BCSU,<index>:;ZWUC:TCSM,<ater_pcm>:<TR3_type>,0;ZWGA:<ater_pcm-tsl>:<a_pcm-tsl>;

12.2.6.4 Create the TC1C1 track 4 TCSM units and plug-in units

Two options a) when ET16 is used for A-interface and b) whenETIP1-A used for A-interface ( in case A-interface upgraded earlierfor ETIP1-A)

a. TCSM unit when ET16 in use (A-interface ET master)ZWTU:TCSM,<ater_pcm>:1x2-0;ZWTP:TCSM,<ater_pcm>:<TR3_type>,0,4,::GENERAL,8,<ater_pcm>,TSL,1::;

b. TCSM unit when Transmission protected ETIP1-A in use (A-interface ET master) ( in case A-interface upgraded earlierfor ETIP1-A)

ZWTU:TCSM, <ater_pcm>:1x2-0; // TCSM unit in TC1C1ZWTP:TCSM,<ater_pcm>:<TR3_type>,0,4,::GENERAL,8,<ater_pcm>,TSL,1::;

ZWTP:TCSM,<ater_pcm>:ETIP1_A,0,17,:::; // in case HW and transmissionredundancy in useZWTP:TCSM,<ater_pcm>:ETIP1_A,0,25,:::; // in case HW redundancy in use

a) Example of TC1C1 first 4 TCSM unit creation under TC1C1 ( whenA-interface ET16 in use and Ater interface ETIP1-A in use):

ZWTU:TCSM,320:1x2-0:; //A-IF TR3 master // A-if ET16 masterZWTP:TCSM,320:TR3T,0,1,::GENERAL,8,320,TSL,1::;ZWTP:TCSM,320,:ET16,0,14,:::;ZWGC:320,1:POOL=32:BCSU,0:;ZWUC:TCSM,320:TR3T,0;

ZWTU:TCSM,321:1x2-0:;"); //Clock masterZWTU:TCSM,321:1x1-0:;ZWTP:TCSM,321:1x2-0:TR3T,0,2,::GENERAL,8,321,TSL,1::;ZWTP:TCSM,321,1x1-0:CL3TG,0,19:;ZWTP:TCSM,321,1x2-0:CL3TG,1,19:;ZWGC:321,1:POOL=32:BCSU,0:;ZWUC:TCSM,321:TR3T,0;

ZWTU:TCSM,322:1x1-0:;"); //Ater ETIP masterZWTU:TCSM,322:1x2-0:; // Redundant ETIP unitZWTP:TCSM,322:1x2-0:TR3T,0,3,::GENERAL,8,322,TSL,1::;ZWTP:TCSM,322:1x1-0:ETIP1_A,0,13,:::; //master ETIPZWTP:TCSM,322,1x2-0:ETIP1_A,1,13,:::; //redundant ETIPZWGS:322:1:;


32 (104)

ZWGC:322,1:POOL=32:BCSU,0:;ZWUC:TCSM,322:TR3T,0;ZWGA:322-31:1-31:;

ZWTU:TCSM,323:1x2-0:; //Fourth TCSM unitZWTP:TCSM,323:1x2-0:TR3T,0,4,::GENERAL,8,323,TSL,1::;ZWTP:TCSM,322:1x2-0:ETIP1_A,0,17,:::; //master ETIPZWTP:TCSM,322,1x2-0:ETIP1_A,1,25,:::; //redundant ETIP

ZWGC:324,1:POOL=32:BCSU,0:;ZWUC:TCSM,324:TR3T,0;

12.2.7 Create rest of the TCSM units to TC1C-1 and 0

Note!! Remember to check and create the A-and Ater-interface master units see table in chapter 10 Master unitsin TCSM site

12.2.7.1 Create the TCSM(s) units for TR3 and ET16 or ETIP1-A

ZWTU:TCSM:<coordinate of cartridge>;

12.2.7.2 Create the TR3E/TR3A/TR3T plug-in units

ZWTP:TCSM,<ater_pcm>:<location>:<TR3_type>,<piuindex>,<track>::GENERAL,8,<ater_pcm>,<TSL type>,<TSL>;

12.2.7.3 Create the ET16 for A-interface (TR3 A-interface O&M masters located in tracks 1, 5,9, 28, 32,36)

ZWTP:TCSM,<ater_pcm>:ET16,<piu index>,<track>:;

12.2.7.4 Create the ETIP1-A for Ater interfaces (TR3 Ater-interface O&M masters located in tracks3,7,11,30,34,38)

ZWTP:TCSM,<ater_pcm>:ETIP1_A,<piu index>,<track>:;

12.2.7.5 Create the ETIP1-A for A-interfaces (TR3 A-interface O&M masters located in tracks 4,8,12 ,31,35,39) (in case A-interface upgraded earlier for ETIP1-A)

ZWTP:TCSM,<ater_pcm>:ETIP1_A,<piu index>,<track>:;Remember to create both master and protected units in case HW redundancy in use

12.2.7.6 Connect TCSM unit

ZWUC:TCSM,<ater_pcm>:<TR3A/E/T>,<index>;

12.2.7.7 Set the number of through connections

ZWGS:<highway pcm number>:<number of through connected channels>;

12.2.7.8 Create the TC-PCM

ZWGC:<highway pcm number>:POOL=<tc_pcm pool>:BCSU,<index>;

12.2.7.9 Create the through connections

ZWGA:<highway pcm circuit(PCM-TSL)>:<tc_pcm circuit(PCM-TSL)> ;


33 (104)

12.2.8 Create IP/PW locally to the Ater master and redundant ETIP1-A units

This step is to be done locally. The first PWE tunnel and PW need to beconfigured locally to ETIP plug-in unit. The rest of the PWE tunnels andPW can be configured from BSC site. Configuring the IP and PW forETIP unit can be done following the document: PWT User Guide(document’s chapter 4 and 5). See NED document “PWT User Guide”for more information.

12.2.8.1 Configure locally master ETIP1-A unit for Ater interface PW

a. from back panel with CPCU020 cable connection in ETIP1-A card inTC1C-0 track 13

Service Terminal connection to ETIP1-A is available through the back panel. Connect CPCU020 cable(C104887) to the back panel connector 4P with traffic parameters 9600/ Even / 7.

Username: rootPassword: root1234

b. from front panel cable connection in ETIP1-A card in TC1C-0 track13

Take a SSH session with a direct Ethernet cable attached into front-panel SFP module. The card defaultaddress is 192.168.1.111/24 and the client must use IP address from 192.168.1.0/24 subnet.

Username; rootPassword: root1234

Modify IP address, VLAN and route use linux vi-editor

12.2.8.2 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor

vi /opt/etip_tcsm_ip_conf.sh

ifconfig pw_mana0.<vlan_id> <vlan_ip> netmask xxx.xxx.xxx.xxxifconfig pw0.<vlan_id> <vlan_ip> netmask xxx.xxx.xxx.xxxifconfig pw_mana0 up

Exit with ESC and :ZZ or ESC save with :w and exit with :q!

Example:ifconfig pw_mana0.152 10.16.65.180 netmask 255.255.255.248ifconfig pw0.153 10.16.65.188 netmask 255.255.255.248ifconfig pw_mana0 up

12.2.8.3 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor

vi /opt/etip_tcsm_vlan_conf.sh

vconfig add pw_mana0 <vlan_id>vconfig add pw0 <vlan_id>



34 (104)

Example:vi /opt/etip_tcsm_vlan_conf.sh

vconfig add pw_mana0 152vconfig add pw0 153

12.2.8.4 Configure the static network routes to script file using vi –editor

vi /opt/etip_tcsm_routes_conf.sh

route add -net <destination ip for TCSM pw_mana0> netmask xxx.xxx.xxx.xxxgw <gw_address of TCSM pw_mana0>route add -net <destination ip for TCSM pw0> netmask xxx.xxx.xxx.xxx gw<gw_address of TCSM pw0>

Exit with ESC and :ZZ or ESC save with :w and exit with :q!Example:


route add -net 10.16.65.160 netmask 255.255.255.248 gw 10.16.65.177route add -net 10.16.65.168 netmask 255.255.255.248 gw 10.16.65.185

12.2.8.5 Restart the ETIP master unit

lnx-hwapi-tool -f 0

12.2.8.6 Configure locally the redundant ETIP1-A unit for Ater interface PW by using local cableconnection in ETIP1-A card in TC1C-1 track 13

a. from back panel with CPCU020 cable connection in ETIP1-A card inTC1C-1 track 13

Service Terminal connection to ETIP1-A is available through the back panel. Connect CPCU020 cable(C104887) to the back panel connector 4P with traffic parameters 9600/ Even / 7.Username: rootPassword: root1234

b. from front panel cable connection in ETIP1-A card in TC1C-1 track13 ( In use if ETIP1-A card)




12.2.8.7 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor


ifconfig pw_mana0.<vlan_id> <vlan_ip> netmask xxx.xxx.xxx.xxxifconfig pw0.<vlan_id> <vlan_ip> netmask xxx.xxx.xxx.xxx


35 (104)

ifconfig pw_mana0 up



12.2.8.8 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor






12.2.8.9 Configure the static network routes to script file using vi –editor




vi /opt/etip_tcsm_routes_conf.shroute add -net 10.16.65.160 netmask 255.255.255.248 gw 10.16.65.177route add -net 10.16.65.168 netmask 255.255.255.248 gw 10.16.65.185

12.2.8.10 Restart the ETIP master unit

lnx-hwapi-tool -f 0

12.2.9 Add Tunnel and PW configuration of ETIP master unit for ETIP master TCSM unit in TC1C-0 track3

Add tunnel:lnx-pwe-tool a <TCSM tunnelindex> <destination vlan ip address> -n=<TCSMtunnel name>

Create the PW under the tunnel:


36 (104)

lnx-pwe-tool c <TCSM pwindex> <TCSM tunnelindex> <ludp> <pudp> <pcm> -p=<TCSM PW name>

Name Value Infopwindex 0-65534 PW indextunnelindex 0-65534 Tunnel idludp 1-65535 Local UDP portpudp 1-65535 Peer UDP port

pcm 0-8191PCM line number( in TCSM site starting from 0)

PCM numbering table in Appendix 2: Internal PCM usage for Aterinterface

Change the tunnel state:lnx-pwe-tool j <tunnelindex> ena

Example:lnx-pwe-tool a 322 10.16.65.172 -n=ATERTOETIP2lnx-pwe-tool c 322 322 202 202 2 –p=TCSM322lnx-pwe-tool j 322 ena

12.2.9.1 Go to MML to check the D-channel state

ZDTF;

12.2.9.2 Take the Ater master TCSM unit to TE-EX (in TC1C-0 track 3)

When the d-channel for TCSM is up take the unit up:ZUSC:TCSM,<ater_pcm>:SE;ZUSC:TCSM,<ater_pcm>:TE;

12.2.9.3 Connect locally to Ater ETIP1-A master unit (in TC1C-0 track 13) and upload the configurationfrom ETIP1-A card to TR3 card:

lnx-config-tool -u TR3

12.2.9.4 Take the Ater master TCSM unit to WO-EX

ZUSC:TCSM,<ater_pcm>:WO;

When the Ater master TCSM unit D-channel is in WO-EX continueconfiguring the rest of the TCSM units via MML

12.2.10 Create new PSN tunnel (or use the one created to Ater master)

Use the QYA MML command or the lnx-pwe-tool a command locally from ETIP to create a new PSN tunnel.ZQYA:<unit type>,<unit index>,<interface type>:<tunnel index>:<dst IPaddress>:<tunnel name>;


37 (104)

Name Value Info

unit type



tunnel index 0-65534Numerical identifier for PSN tunnel (Obligatory,must be unique at least inside one ETIP1-A


tunnel nameName for PSN tunnel (Optional, default value is “”,max length 20)

Example:ZQYA:TCSM,324,ATER:322:"10.16.65.188":ATERTOTCSM324:;


Use the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunnel.ZQYC:<unit type>,<unit index>,<interface type>:<PW index>: <tunnelindex>:<local UDP port>,<peer UDP port>:<PCM number>:<tsl mapping>:<JBlength>:<number of frames>:<ToS field>:<VLAN priority>:<PW name>;

Name Value Info

unit typeType of configured unit Type of configured unit (Obligatory,ETIP for ETIPs in BSC3i and TCSM for ETIPs in TCSM3i)


interface type A or Ater A-interface or Ater (only when unit type TCSM)

PW 0-65534Numerical identifier for PW (Obligatory, must be unique atleast inside one ETIP1-A (Obligatory)


local UDP port 1-65535 Number of local UDP port (Obligatory)

peer UDP port Number of peer UDP port (Obligatory)

PCM number

0-8191(ETIP)

PCM line number (Obligatory)0-127 (TCSM)

tsl mapping 31-Jan List of timeslots(Optional, default is timeslots 1-31)

JB lenght 1-192

Jitter Buffer length in frames, settable by one frame (125us)steps (Optional, default value is 40 (+/-5ms), range from 1 (+/-125us ) to 192 (+/-24ms))

number of frames Jan-40Number of collected TDM frames per Ethernet packet(Optional, default is 8)



38 (104)

VLAN priority 0-7

VLAN priority (Optional, if does not set value from IPmanagement is used instead, if there is no VLAN set in IPmanagement this parameter will be ignored)


Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;ZQYC:TCSM,322,ATER:321:322:201,201:1::::::TCSM321:;ZQYC:TCSM,322,ATER:323:322:203,203:2::::::TCSM323:;//TCSM322 commands has been given locally in ETIP card//


Use the QYJ MML command to enable all the PWs in a tunnel.ZQYJ:ETIP,<unit index>,<interface type>: <tunnel index>:<action>;

Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)tunnel index 0-65534 Numerical identifier for PSN tunnel (Obligatory)action ENA/DIS Action to perform (Obligatory)

Example:ZQYJ:TCSM,322,ATER:322:ENA;


ZQYE:<unit type>,<unit index>,<interface type>:<PW index>:<action>;

Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:TCSM,322,ATER:320:ENA;ZQYE:TCSM,322,ATER:321:ENA;ZQYE:TCSM,322,ATER:323:ENA;//TCSM322 commands has been given locally in ETIP card/

12.2.10.3 Verify information


39 (104)


Name Value Info

unit type






ZDTF;

12.2.10.5 Take the TCSM unit to WO-EX

When the d-channel for TCSM is up take the unit up:ZUSC:TCSM,<ater_pcm>:SE;ZUSC:TCSM,<ater_pcm>:TE;ZUSC:TCSM,<ater_pcm>:WO;

12.2.11 Move traffic back to TC1C 0 and 1 cartridge

Create needed A-interface configuration to standalone TCSM related to ETIP. See more instructions from NEDdocument BSS IntegrationAfter that, move traffic back to new ETIP unit.

12.2.11.1 Change the PCM number of the A-interface link with ZNCM MML command if needed

Modify the link PCM number:ZNCM:<link_number>:<new_pcm>;

Allow link activation:ZNLA:<link_number>;

Cange the links state:ZNLC:<link_number>:ACT;

12.2.11.2 Create circuits back and take the circuits up

Create circuit group:ZRCC:TYPE=CCS,NCGR=<ciruit group name>,CGR=<circuit groupnumber>:DIR=<direction>,NET=<signalling network>,SPC=<msc signalling pointcode>,LSI=<line signalling>;


40 (104)

Create circuits under circuit group:ZRCA:CGR=1:ETPCM=<etpcm>,CRCT=<circuits>:CCSPCM=<number of PCM system>:;

Change the state of the speech circuits (CEC).ZCEC:ETPCM=<etpcm>,CRCT=<circuit>:<state>;ZCEC:ETPCM=<circuit>,CRCT=<circuit>:WO;

12.2.11.3 Restart the TCSM units with code loading

ZUSU:TCSM,<index>:C=TOT;


41 (104)

12.3 TC1C 2 (optional)

12.3.1 Move traffic from TC1C 2 cartridge

Move traffic from TC1C 2 cartridge to be upgraded.



Inactivate the A-interface links affected to TC1C-2 TCSM’s




ZNLD:<link_number>;













12.3.3 Delete TCSM/ET16/TR3 from TC1C 2 cartridgeDelete Ater ET16/TR3 equipment related to TCSM units.

Delete Ater TCSM(s) and ET16/TR3 unit equipments from TC1C-2 withfollowing commands:

ZWTQ:TCSM,<index>:<location>:<piu type>,<index>;ZWTV:TCSM,<index>,<location>;


42 (104)



In this step, ET16 plug-in unit cables are disconnected.Remove cablings from TC1C 2 cartridge according to following table:TCSA_162 TC1C 2 3.0B 13.1A IC203-A CPETS-F 00B 12 CPSM021 ET ATER Interface externalTCSA_163 TC1C 2 3.0B 13.1J IC203-A CPETS-F 00B 13 CPSM022 ET ATER Interface externalTCSA_164 TC1C 2 3.0B 13.1R IC203-A CPETS-F 00B 14 CPSM021 ET ATER Interface externalTCSA_165 TC1C 2 3.0B 23.1A IC203-A CPETS-F 00B 15 CPSM020 ET ATER Interface externalTCSA_166 TC1C 2 3.0B 23.1J IC203-A CPETS-F 00B 16 CPSM018 ET ATER Interface externalTCSA_167 TC1C 2 3.0B 23.1R IC203-A CPETS-F 00B 17 CPSM019 ET ATER Interface external

12.3.5 Remove ET16 PIUs

Remove ET16 plug-in units from TC1C 2 cartridge track 13 and/or 23.12.3.6 Create the TCSM units to TC1C-2


12.3.6.1 Create the TCSM(s) units for TR3 and ET16 units




12.3.6.3 Create the ET16 for A-interface (TR3 A-interface O&M masters located in tracks 1, 5, 9, 28,32,36)


Create the ETIP1-A for Ater interfaces (TR3 Ater-interface O&M masters located in tracks 3,7,11,30,34,38):ZWTP:TCSM,<ater_pcm>:ETIP1_A,<piu index>,<track>:;

12.3.6.4 Create the ETIP1-A for A-interfaces (TR3 A-interface O&M masters located in tracks4,8,12,31,35,39) (in case A-interface upgraded earlier for ETIP1-A)









43 (104)


ZWGA:<highway pcm circuit(PCM-TSL)>:<tc_pcm circuit(PCM-TSL)>;

12.3.7 Create IP/PWThis step is to be done manually. Configuring the IP and PW for ETIPunit can be done following the document: PWT User Guide (document’schapter 4 and 5). See NED document “PWT User Guide” for moreinformation.

Use existing Ater ETIP Master TCSM when creating tunnels and PWs toother TCSMs.

12.3.7.1 Create new PSN tunnel ( or use the one created to Ater master)


Name Value Info

unit type








Use the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunneZQYC:<unit type>,<unit index>,<interface type>:<PW index>: <tunnelindex>:<local UDP port>,<peer UDP port>:<PCM number>:<tsl mapping>:<JBlength>:<number of frames>:<ToS field>:<VLAN priority>:<PW name>;

Name Value Info







44 (104)



PCM number



JB lenght 1-192




VLAN priority 0-7



Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;

12.3.7.3 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)Use the QYJ MML command to enable all the PWs in a tunnel.

ZQYJ:ETIP,<unit index>: <tunnel index>:<action>;

Name Value Info

unit type





ZQYE:<unit type>,<unit index>,<interface type>:<PW index>:<action>;Name Value Info

unit typeType of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i and TCSM


45 (104)

for ETIPs in TCSM3i)unit index Index of ETIP or TCSM unit (Obligatory)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:TCSM,322,ATER:320:ENA;ZQYE:TCSM,322,ATER:321:ENA;ZQYE:TCSM,322,ATER:323:ENA;//TCSM322 commands has been given locally in ETIP card//


ZDTF;



12.3.8 Move traffic back to TC1C 2 cartridge


12.3.8.1 Change the PCM number of the A-interface link with ZNCM MML command if needed

Modify the link PCM number:ZNCM:<link_number>:<new_pcm>;



12.3.8.2 Create circuits back and take the circuits up

Create circuit group:ZRCC:TYPE=CCS,NCGR=<ciruit group name>,CGR=<circuit groupnumber>:DIR=<direction>,NET=<signalling network>,SPC=<msc signalling pointcode>,LSI=<line signalling>;


Change the state of the speech circuits (CEC).


46 (104)

ZCEC:ETPCM=<etpcm>,CRCT=<circuit>:<state>;ZCEC:ETPCM=<circuit>,CRCT=<circuit>:WO;




47 (104)










ZNLD:<link_number>;













12.4.3 Delete TCSM/ET16/TR3 from TC1C 3 cartridge

Delete ET16/TR3 equipment related to TCSM units.

Delete TCSM(s) and ET16/TR3 unit equipments with followingcommands:


48 (104)












12.4.6.3 Create the ET16 for A-interface (TR3 A-interface O&M masters located in tracks 1, 5, 9,28,32,36)











49 (104)









Name Value Info

unit type








Use the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunnel.

ZQYC:<unit type>,<unit index>,<interface type>:<PW index>: <tunnelindex>:<local UDP port>,<peer UDP port>:<PCM number>:<tsl mapping>:<JBlength>:<number of frames>:<ToS field>:<VLAN priority>:<PW name>;

Name Value Info





50 (104)





PCM number



JB lenght 1-192




VLAN priority 0-7



Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;



Name Value Info

unit type






51 (104)


Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:TCSM,322,ATER:320:ENA;


ZDTF;





12.4.8.1 Change the PCM number of the A-interface link with ZNCM MML command if neededModify the link PCM number:

ZNCM:<link_number>:<new_pcm>;



12.4.8.2 Create circuits back and take the circuits upCreate circuit group:

ZRCC:TYPE=CCS,NCGR=<ciruit group name>,CGR=<circuit groupnumber>:DIR=<direction>,NET=<signalling network>,SPC=<msc signalling pointcode>,LSI=<line signalling>;


Change the state of the speech circuits (CEC).


52 (104)

ZCEC:ETPCM=<etpcm>,CRCT=<circuit>:<state>;ZCEC:ETPCM=<circuit>,CRCT=<circuit>:WO;




53 (104)










ZNLD:<link_number>;













12.5.3 Delete TCSM/ET16/TR3 from TC1C 4 cartridge

Delete ET16/TR3 equipment related to TCSM units.

Delete TCSM(s) and ET16/TR3 unit equipments with followingcommands:


54 (104)












12.5.6.3 Create the ET16 for A-interface (TR3 A-interface O&M masters located in tracks 1, 5, 9,28,32,36)











55 (104)









Name Value Info

unit type








Use the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunnel.ZQYC:<unit type>,<unit index>,<interface type>:<PW index>: <tunnelindex>:<local UDP port>,<peer UDP port>:<PCM number>:<tsl mapping>:<JBlength>:<number of frames>:<ToS field>:<VLAN priority>:<PW name>;

Name Value Info






56 (104)




PCM number



JB lenght 1-192




VLAN priority 0-7



Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;12.5.7.3 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)


Name Value Info

unit type






Name Value Info


57 (104)

unit type



Example:ZQYE:TCSM,322,ATER:320:ENA;


ZDTF;





12.5.8.1 Change the PCM number of the A-interface link with ZNCM MML command if neededModify the link PCM number:

ZNCM:<link_number>:<new_pcm>;



12.5.8.2 Create circuits back and take the circuits upCreate circuit group:

ZRCC:TYPE=CCS,NCGR=<ciruit group name>,CGR=<circuit groupnumber>:DIR=<direction>,NET=<signalling network>,SPC=<msc signalling pointcode>,LSI=<line signalling>;


Change the state of the speech circuits (CEC).ZCEC:ETPCM=<etpcm>,CRCT=<circuit>:<state>;


58 (104)

ZCEC:ETPCM=<circuit>,CRCT=<circuit>:WO;




59 (104)

13 A-INTERFACE ETIP1-A IMPLEMENTATION FOR IP/PWE IN STANDALONE TCSM

This chapter includes the instructions how to install ETIP1-A plug-in unit used as A Interface in StandaloneTCSM3i installation. This chapter is devided for following different options:

Option1: Use of ETIP for A-if for transmission redundancy

ETIP1-A unit at TC1C1 track 17

Option2: Use of ETIP for A-if for Hardware redundancy

ETIP1-A unit at TC1C1 track 17 and Track-25

13.1 Option1 :- ETIP with transmission redundancy TC1C1 ETIP1-A

This chapter supports upgrade for TC1C1 cartridge so that all ET16 units at TRACK-14,15,16,24,25,26 areremoved and are replaced with one ETIP1-A plug-in unit at TRACK-17.

13.1.1 Move traffic from ET16 Units from track-14,15,16,24,25,26 of TC1C1 TCSM(s)

Remove traffic form TR3T-1,5,9,28,32 and 36

NOTE:Do not delete A-interface speech channels and/or TR3 plug-in units. It is enough that existing TCSM unitsare in SE-NH state.

13.1.2 Delete ET16 PIU(s) from TC1C1 cartridge

Delete ET16 plug-in units from TC1C1:ZWTQ:TCSM,<index>,<coordinate>:ET16,<index>;ZWTV:TCSM,<index>,<coordinate>;

13.1.3 Remove cables

Remove cables between the TCSA cabinet (TC1C1) and the cabling cabinet according to following table:TCSA_204 TC1C 1 2.0B 14.1A IC203-A CPETS-F 00B 54 CPSM014 ET A InterfaceTCSA_205 TC1C 1 2.0B 14.1J IC203-A CPETS-F 00B 55 CPSM015 ET A InterfaceTCSA_206 TC1C 1 2.0B 14.1R IC203-A CPETS-F 00B 56 CPSM014 ET A InterfaceTCSA_207 TC1C 1 2.0B 14.1Z IC203-A CPETS-F 00B 57 CPSM015 ET A InterfaceTCSA_208 TC1C 1 2.0B 15.1A IC203-A CPETS-F 00B 58 CPSM013 ET A InterfaceTCSA_209 TC1C 1 2.0B 15.1J IC203-A CPETS-F 00B 59 CPSM014 ET A InterfaceTCSA_210 TC1C 1 2.0B 15.1R IC203-A CPETS-F 00B 60 CPSM013 ET A InterfaceTCSA_211 TC1C 1 2.0B 15.1Z IC203-A CPETS-F 00B 61 CPSM014 ET A InterfaceTCSA_212 TC1C 1 2.0B 16.1A IC203-A CPETS-F 00B 62 CPSM012 ET A InterfaceTCSA_213 TC1C 1 2.0B 16.1J IC203-A CPETS-F 00B 63 CPSM013 ET A InterfaceTCSA_214 TC1C 1 2.0B 16.1R IC203-A CPETS-E 01B 00 CPSM011 ET A InterfaceTCSA_215 TC1C 1 2.0B 16.1Z IC203-A CPETS-E 01B 01 CPSM012 ET A InterfaceTCSA_216 TC1C 1 2.0B 24.1A IC203-A CPETS-E 01B 02 CPSM010 ET A InterfaceTCSA_217 TC1C 1 2.0B 24.1J IC203-A CPETS-E 01B 03 CPSM011 ET A InterfaceTCSA_218 TC1C 1 2.0B 24.1R IC203-A CPETS-E 01B 04 CPSM010 ET A InterfaceTCSA_219 TC1C 1 2.0B 24.1Z IC203-A CPETS-E 01B 05 CPSM011 ET A InterfaceTCSA_220 TC1C 1 2.0B 25.1A IC203-A CPETS-E 01B 06 CPSM009 ET A InterfaceTCSA_221 TC1C 1 2.0B 25.1J IC203-A CPETS-E 01B 07 CPSM010 ET A InterfaceTCSA_222 TC1C 1 2.0B 25.1R IC203-A CPETS-E 01B 08 CPSM009 ET A InterfaceTCSA_223 TC1C 1 2.0B 25.1Z IC203-A CPETS-E 01B 09 CPSM010 ET A InterfaceTCSA_224 TC1C 1 2.0B 26.1A IC203-A CPETS-E 01B 10 CPSM008 ET A InterfaceTCSA_225 TC1C 1 2.0B 26.1J IC203-A CPETS-E 01B 11 CPSM009 ET A InterfaceTCSA_226 TC1C 1 2.0B 26.1R IC203-A CPETS-E 03B 00 CPSM010 ET A InterfaceTCSA_227 TC1C 1 2.0B 26.1Z IC203-A CPETS-E 03B 01 CPSM011 ET A Interface


60 (104)

13.1.4 Remove sync cables in case connected to TC1C1 tracks

Remove sync cables from TC1C1 end in case connected to TC1C1 tracks


TCSA_066 TC1C 0 1.0B 02.4A TC1C 1 2.0B 02.4A CHQ006 AL and CGSTCSA_067 TC1C 0 1.0B 02.4P TC1C 1 2.0B 02.4P CHQ006 AL and CGS

TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027

SYNC ETxx SYNC signal 11)

TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027

SYNC Etxx SYNC signal 21)

TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


The 4 Synchronisation cables TCSA_080 - TCSA_083 are connected in factory at the CLOCK and TC1C0 asspecified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to the table below:

From To ET Type1.0B 21.2Q/2S/2U/2W .0B 10.2B/2D/2F/2Q or

.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A

13.1.5 Add modules and new cables

Add Rear Connector Module RCOM-B + one ADMOD07 Module :Position Name FU Use Note2.0B 18.1A RCOM-B TC1C1 Rear Connector Module for ETIP1-A Install RCOM to

tracks 17 and 182.0B 17.4E ADMOD07 TC1C1

13.1.6 Replace ET16 PIU(s) with ETIP1-A plug-in unit

Remove ET16 plug-in units from TC1C1 cartridge.Install ETIP1-A plug-in unit to TC1C1 track 17.

13.1.7 Synchronization usage with ETIP

When using transmission equipment between the ETIP’s and other ends if the equipment is not supporting ThePseudo wire timing over packet (ToP) synchronization, then you need to get the synchronization via other line.More info in NED: PWT user guide in chapter Synchronizing ETIP clock.

13.1.8 Create A-interface ETIP1-A plug-in unit to needed TR3 units

ETIP plug-in unit must be created to all A-ETIP Master TCSM(s) according the following table:NOTE:


61 (104)

Create TR3 plug-in units for the A-ETIP Master TCSM(s) if not exists.

A-ETIP masterTR3 plug-in unit tracks

TC1C1 TR3 track 4,8,12,31,35,39

Create the A-ETIP Master TCSM units.ZWTU:TCSM,<unit index>:1x2-0;

Create the ETIP1-A plug-in unit to A ETIP master TCSM(s):ZWTP:TCSM,<unit index>,1x2-0:ETIP1_A,0,17;

13.1.9 Please refer APPENDIX-1 for sample creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel


ZDTF;


When the D-channel for TCSM is up take the unit up:ZUSC:TCSM,<ater_pcm>:SE;ZUSC:TCSM,<ater_pcm>:TE;ZUSC:TCSM,<ater_pcm>:WO;

13.1.10 Move traffic back to TC1C1 TCSM(s)

Move traffic back to new ETIP unit.


62 (104)

13.2 ETIP with transmission redundancy TC1C0 ETIP1-A








Remove cables between the TCSA cabinet (TC1C0) and the cabling cabinet according to following table:TCSA_180 TC1C 0 1.0B 14.1A IC203-A CPETS-F 00B 30 CPSM013 ET A InterfaceTCSA_181 TC1C 0 1.0B 14.1J IC203-A CPETS-F 00B 31 CPSM013 ET A InterfaceTCSA_182 TC1C 0 1.0B 14.1R IC203-A CPETS-F 00B 32 CPSM013 ET A InterfaceTCSA_183 TC1C 0 1.0B 14.1Z IC203-A CPETS-F 00B 33 CPSM013 ET A InterfaceTCSA_184 TC1C 0 1.0B 15.1A IC203-A CPETS-F 00B 34 CPSM012 ET A InterfaceTCSA_185 TC1C 0 1.0B 15.1J IC203-A CPETS-F 00B 35 CPSM012 ET A InterfaceTCSA_186 TC1C 0 1.0B 15.1R IC203-A CPETS-F 00B 36 CPSM012 ET A InterfaceTCSA_187 TC1C 0 1.0B 15.1Z IC203-A CPETS-F 00B 37 CPSM012 ET A InterfaceTCSA_188 TC1C 0 1.0B 16.1A IC203-A CPETS-F 00B 38 CPSM011 ET A InterfaceTCSA_189 TC1C 0 1.0B 16.1J IC203-A CPETS-F 00B 39 CPSM012 ET A InterfaceTCSA_190 TC1C 0 1.0B 16.1R IC203-A CPETS-F 00B 40 CPSM011 ET A InterfaceTCSA_191 TC1C 0 1.0B 16.1Z IC203-A CPETS-F 00B 41 CPSM012 ET A InterfaceTCSA_192 TC1C 0 1.0B 24.1A IC203-A CPETS-F 00B 42 CPSM010 ET A InterfaceTCSA_193 TC1C 0 1.0B 24.1J IC203-A CPETS-F 00B 43 CPSM011 ET A InterfaceTCSA_194 TC1C 0 1.0B 24.1R IC203-A CPETS-F 00B 44 CPSM010 ET A InterfaceTCSA_195 TC1C 0 1.0B 24.1Z IC203-A CPETS-F 00B 45 CPSM011 ET A InterfaceTCSA_196 TC1C 0 1.0B 25.1A IC203-A CPETS-F 00B 46 CPSM009 ET A InterfaceTCSA_197 TC1C 0 1.0B 25.1J IC203-A CPETS-F 00B 47 CPSM010 ET A InterfaceTCSA_198 TC1C 0 1.0B 25.1R IC203-A CPETS-F 00B 48 CPSM009 ET A InterfaceTCSA_199 TC1C 0 1.0B 25.1Z IC203-A CPETS-F 00B 49 CPSM010 ET A InterfaceTCSA_200 TC1C 0 1.0B 26.1A IC203-A CPETS-F 00B 50 CPSM009 ET A InterfaceTCSA_201 TC1C 0 1.0B 26.1J IC203-A CPETS-F 00B 51 CPSM010 ET A InterfaceTCSA_202 TC1C 0 1.0B 26.1R IC203-A CPETS-F 00B 52 CPSM009 ET A InterfaceTCSA_203 TC1C 0 1.0B 26.1Z IC203-A CPETS-F 00B 53 CPSM010 ET A Interface




63 (104)



TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


The 4 Synchronisation cables TCSA_080 - TCSA_083 are connected in factory at the CLOCK and TC1C0 asspecified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to thetable below:


.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A





Remove ET16 plug-in units from TC1C0 cartridge from Track 14,15,16,24,25,26..Install ETIP1-A plug-in unit to TC1C0 track 17.




ETIP plug-in unit must be created to all A-ETIP Master TCSM(s) according the following table:NOTE:Create TR3 plug-in units for the A-ETIP Master TCSM(s) if not exists.


TC1C0 TR3 track 4,8,12,31,35,39

Create the A-ETIP Master TCSM units.


64 (104)

ZWTU:TCSM,<unit index>:1x1-0;


13.2.9 Please refer APPENDIX-1 for sample creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel


ZDTF;






This chapter supports upgrade for TC1C2 cartridge so that all ET16units at TRACK-14,15,16,24,25,26 areremoved and are replaced with one ETIP1-A plug-in unit at TRACK-17.







Remove cables between the TCSA cabinet (TC1C2) and the cabling cabinet according to following table:TCSA_228 TC1C 2 3.0B 14.1A IC203-A CPETS-E 03B 02 CPSM012 ET A InterfaceTCSA_229 TC1C 2 3.0B 14.1J IC203-A CPETS-E 03B 03 CPSM013 ET A InterfaceTCSA_230 TC1C 2 3.0B 14.1R IC203-A CPETS-E 03B 04 CPSM012 ET A InterfaceTCSA_231 TC1C 2 3.0B 14.1Z IC203-A CPETS-E 03B 05 CPSM013 ET A InterfaceTCSA_232 TC1C 2 3.0B 15.1A IC203-A CPETS-E 03B 06 CPSM011 ET A InterfaceTCSA_233 TC1C 2 3.0B 15.1J IC203-A CPETS-E 03B 07 CPSM012 ET A InterfaceTCSA_234 TC1C 2 3.0B 15.1R IC203-A CPETS-E 03B 08 CPSM011 ET A InterfaceTCSA_235 TC1C 2 3.0B 15.1Z IC203-A CPETS-E 03B 09 CPSM012 ET A InterfaceTCSA_236 TC1C 2 3.0B 16.1A IC203-A CPETS-E 03B 10 CPSM011 ET A InterfaceTCSA_237 TC1C 2 3.0B 16.1J IC203-A CPETS-E 03B 11 CPSM012 ET A InterfaceTCSA_238 TC1C 2 3.0B 16.1R IC203-A CPETS-F 04B 00 CPSM011 ET A InterfaceTCSA_239 TC1C 2 3.0B 16.1Z IC203-A CPETS-F 04B 01 CPSM012 ET A InterfaceTCSA_240 TC1C 2 3.0B 24.1A IC203-A CPETS-F 04B 02 CPSM009 ET A InterfaceTCSA_241 TC1C 2 3.0B 24.1J IC203-A CPETS-F 04B 03 CPSM010 ET A Interface


65 (104)

TCSA_242 TC1C 2 3.0B 24.1R IC203-A CPETS-F 04B 04 CPSM009 ET A InterfaceTCSA_243 TC1C 2 3.0B 24.1Z IC203-A CPETS-F 04B 05 CPSM010 ET A InterfaceTCSA_244 TC1C 2 3.0B 25.1A IC203-A CPETS-F 04B 06 CPSM010 ET A InterfaceTCSA_245 TC1C 2 3.0B 25.1J IC203-A CPETS-F 04B 07 CPSM011 ET A InterfaceTCSA_246 TC1C 2 3.0B 25.1R IC203-A CPETS-F 04B 08 CPSM010 ET A InterfaceTCSA_247 TC1C 2 3.0B 25.1Z IC203-A CPETS-F 04B 09 CPSM011 ET A InterfaceTCSA_248 TC1C 2 3.0B 26.1A IC203-A CPETS-F 04B 10 CPSM010 ET A InterfaceTCSA_249 TC1C 2 3.0B 26.1J IC203-A CPETS-F 04B 11 CPSM011 ET A InterfaceTCSA_250 TC1C 2 3.0B 26.1R IC203-A CPETS-F 04B 12 CPSM010 ET A InterfaceTCSA_251 TC1C 2 3.0B 26.1Z IC203-A CPETS-F 04B 13 CPSM011 ET A Interface





TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


The 4 Synchronisation cables TCSA_080 ÷ TCSA_083 are connected in factory at the CLOCK and TC1C0 asspecified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to the table below:


.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A





Remove ET16 plug-in units from TC1C2 cartridge from Track-14,15,16,24,25,26.Install ETIP1-A plug-in unit to TC1C2 track 17.



66 (104)


13.3.8 Please refer APPENDIX-1 for creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel


ZDTF;






This chapter supports upgrade for TC1C3 cartridge so that all ET16units at TRACK-14,15,16,24,25,26 areremoved and are replaced with one ETIP1-A plug-in unit at TRACK-17.







Remove cables between the TCSA cabinet (TC1C3) and the cabling cabinet according to following table:TCSA_252 TC1C 3 4.0B 14.1A IC203-A CPETS-F 04B 14 CPSM012 ET A InterfaceTCSA_253 TC1C 3 4.0B 14.1J IC203-A CPETS-F 04B 15 CPSM013 ET A InterfaceTCSA_254 TC1C 3 4.0B 14.1R IC203-A CPETS-F 04B 16 CPSM012 ET A InterfaceTCSA_255 TC1C 3 4.0B 14.1Z IC203-A CPETS-F 04B 17 CPSM013 ET A InterfaceTCSA_256 TC1C 3 4.0B 15.1A IC203-A CPETS-F 04B 18 CPSM012 ET A InterfaceTCSA_257 TC1C 3 4.0B 15.1J IC203-A CPETS-F 04B 19 CPSM013 ET A InterfaceTCSA_258 TC1C 3 4.0B 15.1R IC203-A CPETS-F 04B 20 CPSM012 ET A InterfaceTCSA_259 TC1C 3 4.0B 15.1Z IC203-A CPETS-F 04B 21 CPSM013 ET A InterfaceTCSA_260 TC1C 3 4.0B 16.1A IC203-A CPETS-F 04B 22 CPSM011 ET A InterfaceTCSA_261 TC1C 3 4.0B 16.1J IC203-A CPETS-F 04B 23 CPSM012 ET A InterfaceTCSA_262 TC1C 3 4.0B 16.1R IC203-A CPETS-F 04B 24 CPSM011 ET A InterfaceTCSA_263 TC1C 3 4.0B 16.1Z IC203-A CPETS-F 04B 25 CPSM012 ET A InterfaceTCSA_264 TC1C 3 4.0B 24.1A IC203-A CPETS-F 04B 26 CPSM009 ET A InterfaceTCSA_265 TC1C 3 4.0B 24.1J IC203-A CPETS-F 04B 27 CPSM010 ET A InterfaceTCSA_266 TC1C 3 4.0B 24.1R IC203-A CPETS-F 04B 28 CPSM009 ET A InterfaceTCSA_267 TC1C 3 4.0B 24.1Z IC203-A CPETS-F 04B 29 CPSM010 ET A Interface


67 (104)

TCSA_267 TC1C 3 4.0B 25.1A IC203-A CPETS-F 04B 30 CPSM009 ET A InterfaceTCSA_268 TC1C 3 4.0B 25.1J IC203-A CPETS-F 04B 31 CPSM010 ET A InterfaceTCSA_269 TC1C 3 4.0B 25.1R IC203-A CPETS-F 04B 32 CPSM009 ET A InterfaceTCSA_270 TC1C 3 4.0B 25.1Z IC203-A CPETS-F 04B 33 CPSM010 ET A InterfaceTCSA_271 TC1C 3 4.0B 26.1A IC203-A CPETS-F 04B 34 CPSM009 ET A InterfaceTCSA_272 TC1C 3 4.0B 26.1J IC203-A CPETS-F 04B 35 CPSM010 ET A InterfaceTCSA_273 TC1C 3 4.0B 26.1R IC203-A CPETS-F 04B 36 CPSM009 ET A InterfaceTCSA_274 TC1C 3 4.0B 26.1Z IC203-A CPETS-F 04B 37 CPSM010 ET A Interface





TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


The 4 Synchronisation cables TCSA_080 - TCSA_083 are connected in factory at the CLOCK and TC1C0 asspecified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to the table below:


.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A





Remove ET16 plug-in units from TC1C3 cartridge from track-14,15,16,24,25,26.Install ETIP1-A plug-in unit to TC1C3 track 17.



68 (104)





TC1C3 TR3 track 4,8,12,31,35,39



13.4.9 Please refer APPENDIX-1 for creation IP/PW of TC1C-A track 17 ETIP,PSN tunnel


ZDTF;













69 (104)


Remove cables between the TCSA cabinet (TC1C4) and the cabling cabinet according to following table:TCSA_275 TC1C 4 5.0B 14.1A IC203-A CPETS-F 04B 38 CPSM013 ET A InterfaceTCSA_276 TC1C 4 5.0B 14.1J IC203-A CPETS-F 04B 39 CPSM014 ET A InterfaceTCSA_277 TC1C 4 5.0B 14.1R IC203-A CPETS-F 04B 40 CPSM013 ET A InterfaceTCSA_278 TC1C 4 5.0B 14.1Z IC203-A CPETS-F 04B 41 CPSM014 ET A InterfaceTCSA_279 TC1C 4 5.0B 15.1A IC203-A CPETS-F 04B 42 CPSM013 ET A InterfaceTCSA_280 TC1C 4 5.0B 15.1J IC203-A CPETS-F 04B 43 CPSM014 ET A InterfaceTCSA_281 TC1C 4 5.0B 15.1R IC203-A CPETS-F 04B 44 CPSM013 ET A InterfaceTCSA_282 TC1C 4 5.0B 15.1Z IC203-A CPETS-F 04B 45 CPSM014 ET A InterfaceTCSA_283 TC1C 4 5.0B 16.1A IC203-A CPETS-F 04B 46 CPSM012 ET A InterfaceTCSA_284 TC1C 4 5.0B 16.1J IC203-A CPETS-F 04B 47 CPSM013 ET A InterfaceTCSA_285 TC1C 4 5.0B 16.1R IC203-A CPETS-F 04B 48 CPSM012 ET A InterfaceTCSA_286 TC1C 4 5.0B 16.1Z IC203-A CPETS-F 04B 49 CPSM013 ET A InterfaceTCSA_287 TC1C 4 5.0B 24.1A IC203-A CPETS-F 04B 50 CPSM010 ET A InterfaceTCSA_288 TC1C 4 5.0B 24.1J IC203-A CPETS-F 04B 51 CPSM011 ET A InterfaceTCSA_289 TC1C 4 5.0B 24.1R IC203-A CPETS-F 04B 52 CPSM010 ET A InterfaceTCSA_290 TC1C 4 5.0B 24.1Z IC203-A CPETS-F 04B 53 CPSM011 ET A InterfaceTCSA_291 TC1C 4 5.0B 25.1A IC203-A CPETS-F 04B 54 CPSM010 ET A InterfaceTCSA_292 TC1C 4 5.0B 25.1J IC203-A CPETS-F 04B 55 CPSM011 ET A InterfaceTCSA_293 TC1C 4 5.0B 25.1R IC203-A CPETS-F 04B 56 CPSM010 ET A InterfaceTCSA_294 TC1C 4 5.0B 25.1Z IC203-A CPETS-F 04B 57 CPSM011 ET A InterfaceTCSA_295 TC1C 4 5.0B 26.1A IC203-A CPETS-F 04B 58 CPSM010 ET A InterfaceTCSA_296 TC1C 4 5.0B 26.1J IC203-A CPETS-F 04B 59 CPSM011 ET A InterfaceTCSA_297 TC1C 4 5.0B 26.1R IC203-A CPETS-F 04B 60 CPSM010 ET A InterfaceTCSA_298 TC1C 4 5.0B 26.1Z IC203-A CPETS-F 04B 61 CPSM011 ET A Interface





TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


The 4 Synchronisation cables TCSA_080 ÷ TCSA_083 are connected in factory at the CLOCK and TC1C4 asspecified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to the table below:


.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A


70 (104)





Remove ET16 plug-in units from TC1C4 cartridge,Track-14,15,16,24,25,26.Install ETIP1-A plug-in unit to TC1C4 track 17.






TC1C4 TR3 track 4,8,12,31,35,39



13.5.9 Please refer APPENDIX-1 for creation of IP/PW of TC1C4-A track 17 ETIP,PSN tunnel.


ZDTF;






71 (104)

13.6 Option2: ETIP HW redundancy so that TC1C1 track 17 contains ETIP1-A(Active), TC1C1 track 25 contains ETIP1-A(Redundent).

This chapter supports upgrade for TC1C1 cartridge so that all ET16 plug-in units at track -14,15,16,24,25,26 areupgraded (replaced) with one ETIP1-A plug-in unit at track-17 andRedndent ETIP is placed at Track-25.Note!When upgrading TC1C1 redundancy ETIP plug-in unit in track 25, the old configuration (ET16 ETPCM(s),maximum 4 x TR3 plug-in units) needs to be deleted from track 24,25,26. The traffic cannot be moved back tonew unit and this action means traffic lost.

13.6.1 Move traffic from TC1C1 TCSM(s)

Move traffic from ETPCMs track-14,15,16,25,26,27used in TC1C1 cartridge:

ET TC1C cartridge + Notecartridge + track TR3 plug-in unit tracks

TC1C1 TC1C1 TR3 tracks TR3E-1,5,9,28,32,36

Note!Do not delete A-interface speech channels and/or TR3 plug-in units. It is enough that TCSM(s) are SE-NH state.

13.6.2 Delete ET16 PIU(s) from TC1C cartridges

Delete ET16 plug-in units from TC1C1 (track 14,15,16,24,25,26)ZWTQ:TCSM,<index>,<coordinate>:ET16,<index>;ZWTV:TCSM,<index>,<coordinate>;


Remove Following cables from TC1C1 and the cabling cabinet according to following table:TCSA_204 TC1C 1 2.0B 14.1A IC203-A CPETS-F 00B 54 CPSM014 ET A InterfaceTCSA_205 TC1C 1 2.0B 14.1J IC203-A CPETS-F 00B 55 CPSM015 ET A InterfaceTCSA_206 TC1C 1 2.0B 14.1R IC203-A CPETS-F 00B 56 CPSM014 ET A InterfaceTCSA_207 TC1C 1 2.0B 14.1Z IC203-A CPETS-F 00B 57 CPSM015 ET A InterfaceTCSA_208 TC1C 1 2.0B 15.1A IC203-A CPETS-F 00B 58 CPSM013 ET A InterfaceTCSA_209 TC1C 1 2.0B 15.1J IC203-A CPETS-F 00B 59 CPSM014 ET A InterfaceTCSA_210 TC1C 1 2.0B 15.1R IC203-A CPETS-F 00B 60 CPSM013 ET A InterfaceTCSA_211 TC1C 1 2.0B 15.1Z IC203-A CPETS-F 00B 61 CPSM014 ET A InterfaceTCSA_212 TC1C 1 2.0B 16.1A IC203-A CPETS-F 00B 62 CPSM012 ET A InterfaceTCSA_213 TC1C 1 2.0B 16.1J IC203-A CPETS-F 00B 63 CPSM013 ET A InterfaceTCSA_214 TC1C 1 2.0B 16.1R IC203-A CPETS-E 01B 00 CPSM011 ET A InterfaceTCSA_215 TC1C 1 2.0B 16.1Z IC203-A CPETS-E 01B 01 CPSM012 ET A InterfaceTCSA_216 TC1C 1 2.0B 24.1A IC203-A CPETS-E 01B 02 CPSM010 ET A InterfaceTCSA_217 TC1C 1 2.0B 24.1J IC203-A CPETS-E 01B 03 CPSM011 ET A InterfaceTCSA_218 TC1C 1 2.0B 24.1R IC203-A CPETS-E 01B 04 CPSM010 ET A InterfaceTCSA_219 TC1C 1 2.0B 24.1Z IC203-A CPETS-E 01B 05 CPSM011 ET A InterfaceTCSA_220 TC1C 1 2.0B 25.1A IC203-A CPETS-E 01B 06 CPSM009 ET A InterfaceTCSA_221 TC1C 1 2.0B 25.1J IC203-A CPETS-E 01B 07 CPSM010 ET A InterfaceTCSA_222 TC1C 1 2.0B 25.1R IC203-A CPETS-E 01B 08 CPSM009 ET A InterfaceTCSA_223 TC1C 1 2.0B 25.1Z IC203-A CPETS-E 01B 09 CPSM010 ET A InterfaceTCSA_224 TC1C 1 2.0B 26.1A IC203-A CPETS-E 01B 10 CPSM008 ET A InterfaceTCSA_225 TC1C 1 2.0B 26.1J IC203-A CPETS-E 01B 11 CPSM009 ET A InterfaceTCSA_226 TC1C 1 2.0B 26.1R IC203-A CPETS-E 03B 00 CPSM010 ET A InterfaceTCSA_227 TC1C 1 2.0B 26.1Z IC203-A CPETS-E 03B 01 CPSM011 ET A Interface


72 (104)


Remove sync cables from TC1C1 in case connected to TC1C1 tracks



TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027


1) The 4 Synchronisation cables TCSA_080 ÷ TCSA_083 are connected in factory at the CLOCK andTC1C0 as specified in the table (default positions).However, cartridge and connector positions are freely selectable by the customer according to thetable below:


.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A



Add Rear Connector Module RCOM-B + one ADMOD07 Module + one ADMOD15 Module:Position Name FU Use Note2.0B 18.1A RCOM-B TC1C1 Rear Connector Module for ETIP1-A Install RCOM to

tracks 17 and 182.0B 17.4E ADMOD07 TC1C12.0B 25.4E ADMOD15 TC1C1

Add cablings to TC1C1 cartridges according to following table:Equipping CABLE FROM CABLE TO

No FU Position FU Position Type Use Note

TCSA_520 TC1C 1 2.0B 17.4A TC1C 1 2.0B 25.4A CHFX004 2NTCSA_521 TC1C 1 2.0B 17.4G TC1C 1 2.0B 25.4G CHES004 2NTCSA_530 TC1C 1 2.0B 17.1A TC1C 1 2.0B 25.1A CHQ007 PCMTCSA_531 TC1C 1 2.0B 17.1J TC1C 1 2.0B 25.1J CHQ007 PCMTCSA_532 TC1C 1 2.0B 17.1R TC1C 1 2.0B 25.1R CHQ007 PCM


Remove ET16 plug-in units from TC1C1 cartridge track-14,15,16,24,25,26.Install ETIP1-A plug-in unit to TC1C1 track 17 and 25.


73 (104)

13.6.7 Create TCSM(s) and ETIP1-A plug-in unit

ETIP plug-in units must be created to all A-ETIP Master TCSM(s) according the following table:Note!


A-ETIPTR3 plug-in unit tracks

TC1C1 TR3 track 4,8,12,31,35,39

Create the A-ETIP Master TCSM units:ZWTU:TCSM,<unit index>:1x2-0;ZWTU:TCSM,<unit index>:1x2-0;


Create the redundant ETIP1-A plug-in unit to A ETIP master TCSM(s):ZWTP:TCSM,<unit index>,1x2-0:ETIP1_A,1,25;

13.6.8 For IP/PWE and Tunnel creation Please refer Appendix-2


ZDTF;






74 (104)

13.7 ETIP HW redundancy so that TC1C0 track 17 contains ETIP1-A(Active), TC1C0track 25 contains ETIP1-A(Redundent).

This chapter supports upgrade for TC1C0 cartridge so that all ET16 plug-in units at track -14,15,16,24,25,26 areupgraded (replaced) with one ETIP1-A plug-in unit at track-17 and Redundent ETIP is placed at Track-25.Note!When upgrading TC1C0 redundancy ETIP plug-in unit in track 25, the old configuration (ET16 ETPCM(s),maximum 4 x TR3 plug-in units) needs to be deleted from track 24,25,26. The traffic cannot be moved back tonew unit and this action means traffic lost.

13.7.1 Move traffic from TC1C0 TCSM(s)


ET TC1C1 cartridge + Notecartridge + track TR3 plug-in unit tracks

TC1C0 TC1C0 TR3 Track-1,5,9,28,32,36





Remove Following cables from TC1C0 and the cabling cabinet according to following table:TCSA_180 TC1C 0 1.0B 14.1A IC203-A CPETS-F 00B 30 CPSM013 ET A InterfaceTCSA_181 TC1C 0 1.0B 14.1J IC203-A CPETS-F 00B 31 CPSM013 ET A InterfaceTCSA_182 TC1C 0 1.0B 14.1R IC203-A CPETS-F 00B 32 CPSM013 ET A InterfaceTCSA_183 TC1C 0 1.0B 14.1Z IC203-A CPETS-F 00B 33 CPSM013 ET A InterfaceTCSA_184 TC1C 0 1.0B 15.1A IC203-A CPETS-F 00B 34 CPSM012 ET A InterfaceTCSA_185 TC1C 0 1.0B 15.1J IC203-A CPETS-F 00B 35 CPSM012 ET A InterfaceTCSA_186 TC1C 0 1.0B 15.1R IC203-A CPETS-F 00B 36 CPSM012 ET A InterfaceTCSA_187 TC1C 0 1.0B 15.1Z IC203-A CPETS-F 00B 37 CPSM012 ET A InterfaceTCSA_188 TC1C 0 1.0B 16.1A IC203-A CPETS-F 00B 38 CPSM011 ET A InterfaceTCSA_189 TC1C 0 1.0B 16.1J IC203-A CPETS-F 00B 39 CPSM012 ET A InterfaceTCSA_190 TC1C 0 1.0B 16.1R IC203-A CPETS-F 00B 40 CPSM011 ET A InterfaceTCSA_191 TC1C 0 1.0B 16.1Z IC203-A CPETS-F 00B 41 CPSM012 ET A InterfaceTCSA_192 TC1C 0 1.0B 24.1A IC203-A CPETS-F 00B 42 CPSM010 ET A InterfaceTCSA_193 TC1C 0 1.0B 24.1J IC203-A CPETS-F 00B 43 CPSM011 ET A InterfaceTCSA_194 TC1C 0 1.0B 24.1R IC203-A CPETS-F 00B 44 CPSM010 ET A InterfaceTCSA_195 TC1C 0 1.0B 24.1Z IC203-A CPETS-F 00B 45 CPSM011 ET A InterfaceTCSA_196 TC1C 0 1.0B 25.1A IC203-A CPETS-F 00B 46 CPSM009 ET A InterfaceTCSA_197 TC1C 0 1.0B 25.1J IC203-A CPETS-F 00B 47 CPSM010 ET A InterfaceTCSA_198 TC1C 0 1.0B 25.1R IC203-A CPETS-F 00B 48 CPSM009 ET A InterfaceTCSA_199 TC1C 0 1.0B 25.1Z IC203-A CPETS-F 00B 49 CPSM010 ET A InterfaceTCSA_200 TC1C 0 1.0B 26.1A IC203-A CPETS-F 00B 50 CPSM009 ET A InterfaceTCSA_201 TC1C 0 1.0B 26.1J IC203-A CPETS-F 00B 51 CPSM010 ET A InterfaceTCSA_202 TC1C 0 1.0B 26.1R IC203-A CPETS-F 00B 52 CPSM009 ET A InterfaceTCSA_203 TC1C 0 1.0B 26.1Z IC203-A CPETS-F 00B 53 CPSM010 ET A Interface



75 (104)




TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027




.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A





Add cablings to TC1C1 cartridges according to following table:Equipping CABLE FROM CABLE TO

No FU Position FU Position Type Use NoteTCSA_500 TC1C 0 1.0B 17.4A TC1C 0 1.0B 25.4A CHFX004 2NTCSA_501 TC1C 0 1.0B 17.4G TC1C 0 1.0B 25.4G CHES004 2NTCSA_510 TC1C 0 1.0B 17.1A TC1C 0 1.0B 25.1A CHQ007 PCMTCSA_511 TC1C 0 1.0B 17.1J TC1C 0 1.0B 25.1J CHQ007 PCMTCSA_512 TC1C 0 1.0B 17.1R TC1C 0 1.0B 25.1R CHQ007 PCM






76 (104)



TC1C0 TR3 track 4,8,12,31,35,39






ZDTF;







13.8.1 Move traffic from TC1C TCSM(s)



77 (104)


TC1C2 TC1C2 TR3 Track-1,5,9,28,32,36





Remove Following cables from TC1C2 and the cabling cabinet according to following table:TCSA_228 TC1C 2 3.0B 14.1A IC203-A CPETS-E 03B 02 CPSM012 ET A InterfaceTCSA_229 TC1C 2 3.0B 14.1J IC203-A CPETS-E 03B 03 CPSM013 ET A InterfaceTCSA_230 TC1C 2 3.0B 14.1R IC203-A CPETS-E 03B 04 CPSM012 ET A InterfaceTCSA_231 TC1C 2 3.0B 14.1Z IC203-A CPETS-E 03B 05 CPSM013 ET A InterfaceTCSA_232 TC1C 2 3.0B 15.1A IC203-A CPETS-E 03B 06 CPSM011 ET A InterfaceTCSA_233 TC1C 2 3.0B 15.1J IC203-A CPETS-E 03B 07 CPSM012 ET A InterfaceTCSA_234 TC1C 2 3.0B 15.1R IC203-A CPETS-E 03B 08 CPSM011 ET A InterfaceTCSA_235 TC1C 2 3.0B 15.1Z IC203-A CPETS-E 03B 09 CPSM012 ET A InterfaceTCSA_236 TC1C 2 3.0B 16.1A IC203-A CPETS-E 03B 10 CPSM011 ET A InterfaceTCSA_237 TC1C 2 3.0B 16.1J IC203-A CPETS-E 03B 11 CPSM012 ET A InterfaceTCSA_238 TC1C 2 3.0B 16.1R IC203-A CPETS-F 04B 00 CPSM011 ET A InterfaceTCSA_239 TC1C 2 3.0B 16.1Z IC203-A CPETS-F 04B 01 CPSM012 ET A InterfaceTCSA_240 TC1C 2 3.0B 24.1A IC203-A CPETS-F 04B 02 CPSM009 ET A InterfaceTCSA_241 TC1C 2 3.0B 24.1J IC203-A CPETS-F 04B 03 CPSM010 ET A InterfaceTCSA_242 TC1C 2 3.0B 24.1R IC203-A CPETS-F 04B 04 CPSM009 ET A InterfaceTCSA_243 TC1C 2 3.0B 24.1Z IC203-A CPETS-F 04B 05 CPSM010 ET A InterfaceTCSA_244 TC1C 2 3.0B 25.1A IC203-A CPETS-F 04B 06 CPSM010 ET A InterfaceTCSA_245 TC1C 2 3.0B 25.1J IC203-A CPETS-F 04B 07 CPSM011 ET A InterfaceTCSA_246 TC1C 2 3.0B 25.1R IC203-A CPETS-F 04B 08 CPSM010 ET A InterfaceTCSA_247 TC1C 2 3.0B 25.1Z IC203-A CPETS-F 04B 09 CPSM011 ET A InterfaceTCSA_248 TC1C 2 3.0B 26.1A IC203-A CPETS-F 04B 10 CPSM010 ET A InterfaceTCSA_249 TC1C 2 3.0B 26.1J IC203-A CPETS-F 04B 11 CPSM011 ET A InterfaceTCSA_250 TC1C 2 3.0B 26.1R IC203-A CPETS-F 04B 12 CPSM010 ET A InterfaceTCSA_251 TC1C 2 3.0B 26.1Z IC203-A CPETS-F 04B 13 CPSM011 ET A Interface




78 (104)



TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027




.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A




Add cablings to TC1C2 cartridges according to following table:TCSA_540 TC1C 2 3.0B 17.4A TC1C 2 3.0B 25.4A CHFX004 2NTCSA_541 TC1C 2 3.0B 17.4G TC1C 2 3.0B 25.4G CHES004 2NTCSA_550 TC1C 2 3.0B 17.1A TC1C 2 3.0B 25.1A CHQ007 PCMTCSA_551 TC1C 2 3.0B 17.1J TC1C 2 3.0B 25.1J CHQ007 PCMTCSA_552 TC1C 2 3.0B 17.1R TC1C 2 3.0B 25.1R CHQ007 PCM







79 (104)


TC1C2 TR3 track 4,8,12,31,35,39






ZDTF;










TC1C3 TC1C3 TR3 Track-1,5,9,28,32,36



80 (104)




Remove Following cables from TC1C3 and the cabling cabinet according to following table:TCSA_252 TC1C 3 4.0B 14.1A IC203-A CPETS-F 04B 14 CPSM012 ET A InterfaceTCSA_253 TC1C 3 4.0B 14.1J IC203-A CPETS-F 04B 15 CPSM013 ET A InterfaceTCSA_254 TC1C 3 4.0B 14.1R IC203-A CPETS-F 04B 16 CPSM012 ET A InterfaceTCSA_255 TC1C 3 4.0B 14.1Z IC203-A CPETS-F 04B 17 CPSM013 ET A InterfaceTCSA_256 TC1C 3 4.0B 15.1A IC203-A CPETS-F 04B 18 CPSM012 ET A InterfaceTCSA_257 TC1C 3 4.0B 15.1J IC203-A CPETS-F 04B 19 CPSM013 ET A InterfaceTCSA_258 TC1C 3 4.0B 15.1R IC203-A CPETS-F 04B 20 CPSM012 ET A InterfaceTCSA_259 TC1C 3 4.0B 15.1Z IC203-A CPETS-F 04B 21 CPSM013 ET A InterfaceTCSA_260 TC1C 3 4.0B 16.1A IC203-A CPETS-F 04B 22 CPSM011 ET A InterfaceTCSA_261 TC1C 3 4.0B 16.1J IC203-A CPETS-F 04B 23 CPSM012 ET A InterfaceTCSA_262 TC1C 3 4.0B 16.1R IC203-A CPETS-F 04B 24 CPSM011 ET A InterfaceTCSA_263 TC1C 3 4.0B 16.1Z IC203-A CPETS-F 04B 25 CPSM012 ET A InterfaceTCSA_264 TC1C 3 4.0B 24.1A IC203-A CPETS-F 04B 26 CPSM009 ET A InterfaceTCSA_265 TC1C 3 4.0B 24.1J IC203-A CPETS-F 04B 27 CPSM010 ET A InterfaceTCSA_266 TC1C 3 4.0B 24.1R IC203-A CPETS-F 04B 28 CPSM009 ET A InterfaceTCSA_267 TC1C 3 4.0B 24.1Z IC203-A CPETS-F 04B 29 CPSM010 ET A InterfaceTCSA_267 TC1C 3 4.0B 25.1A IC203-A CPETS-F 04B 30 CPSM009 ET A InterfaceTCSA_268 TC1C 3 4.0B 25.1J IC203-A CPETS-F 04B 31 CPSM010 ET A InterfaceTCSA_269 TC1C 3 4.0B 25.1R IC203-A CPETS-F 04B 32 CPSM009 ET A InterfaceTCSA_270 TC1C 3 4.0B 25.1Z IC203-A CPETS-F 04B 33 CPSM010 ET A InterfaceTCSA_271 TC1C 3 4.0B 26.1A IC203-A CPETS-F 04B 34 CPSM009 ET A InterfaceTCSA_272 TC1C 3 4.0B 26.1J IC203-A CPETS-F 04B 35 CPSM010 ET A InterfaceTCSA_273 TC1C 3 4.0B 26.1R IC203-A CPETS-F 04B 36 CPSM009 ET A InterfaceTCSA_274 TC1C 3 4.0B 26.1Z IC203-A CPETS-F 04B 37 CPSM010 ET A Interface





TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027



From To ET Type1.0B 21.2Q/2S/2U/2W .0B 10.2B/2D/2F/2Q or ET16


81 (104)

.0B 29.2B/2D/2F/2Q1.0B 21.2Q/2S/2U/2W .0B 17.2Q or

.0B 17.2SETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A











TC1C3 TR3 track 4,8,12,31,35,39






ZDTF;


82 (104)










TC1C4 TC1C4 TR3 Track-1,5,9,28,32,36





Remove Following cables from TC1C4 and the cabling cabinet according to following table:TCSA_275 TC1C 4 5.0B 14.1A IC203-A CPETS-F 04B 38 CPSM013 ET A InterfaceTCSA_276 TC1C 4 5.0B 14.1J IC203-A CPETS-F 04B 39 CPSM014 ET A InterfaceTCSA_277 TC1C 4 5.0B 14.1R IC203-A CPETS-F 04B 40 CPSM013 ET A InterfaceTCSA_278 TC1C 4 5.0B 14.1Z IC203-A CPETS-F 04B 41 CPSM014 ET A InterfaceTCSA_279 TC1C 4 5.0B 15.1A IC203-A CPETS-F 04B 42 CPSM013 ET A InterfaceTCSA_280 TC1C 4 5.0B 15.1J IC203-A CPETS-F 04B 43 CPSM014 ET A InterfaceTCSA_281 TC1C 4 5.0B 15.1R IC203-A CPETS-F 04B 44 CPSM013 ET A InterfaceTCSA_282 TC1C 4 5.0B 15.1Z IC203-A CPETS-F 04B 45 CPSM014 ET A InterfaceTCSA_283 TC1C 4 5.0B 16.1A IC203-A CPETS-F 04B 46 CPSM012 ET A InterfaceTCSA_284 TC1C 4 5.0B 16.1J IC203-A CPETS-F 04B 47 CPSM013 ET A InterfaceTCSA_285 TC1C 4 5.0B 16.1R IC203-A CPETS-F 04B 48 CPSM012 ET A InterfaceTCSA_286 TC1C 4 5.0B 16.1Z IC203-A CPETS-F 04B 49 CPSM013 ET A InterfaceTCSA_287 TC1C 4 5.0B 24.1A IC203-A CPETS-F 04B 50 CPSM010 ET A InterfaceTCSA_288 TC1C 4 5.0B 24.1J IC203-A CPETS-F 04B 51 CPSM011 ET A InterfaceTCSA_289 TC1C 4 5.0B 24.1R IC203-A CPETS-F 04B 52 CPSM010 ET A Interface


83 (104)

TCSA_290 TC1C 4 5.0B 24.1Z IC203-A CPETS-F 04B 53 CPSM011 ET A InterfaceTCSA_291 TC1C 4 5.0B 25.1A IC203-A CPETS-F 04B 54 CPSM010 ET A InterfaceTCSA_292 TC1C 4 5.0B 25.1J IC203-A CPETS-F 04B 55 CPSM011 ET A InterfaceTCSA_293 TC1C 4 5.0B 25.1R IC203-A CPETS-F 04B 56 CPSM010 ET A InterfaceTCSA_294 TC1C 4 5.0B 25.1Z IC203-A CPETS-F 04B 57 CPSM011 ET A InterfaceTCSA_295 TC1C 4 5.0B 26.1A IC203-A CPETS-F 04B 58 CPSM010 ET A InterfaceTCSA_296 TC1C 4 5.0B 26.1J IC203-A CPETS-F 04B 59 CPSM011 ET A InterfaceTCSA_297 TC1C 4 5.0B 26.1R IC203-A CPETS-F 04B 60 CPSM010 ET A InterfaceTCSA_298 TC1C 4 5.0B 26.1Z IC203-A CPETS-F 04B 61 CPSM011 ET A Interface





TCSA_080

TC1C 0 1.0B 21.2Q TC1C0

1.0B 10.2B CHE027


TCSA_081

TC1C 0 1.0B 21.2S TC1C0

1.0B 10.2D CHE027


TCSA_082

TC1C 0 1.0B 21.2U TC1C0

1.0B 10.2F CHE027


TCSA_083

TC1C 0 1.0B 21.2W TC1C0

1.0B 10.2Q CHE027




.0B 29.2B/2D/2F/2QET16

1.0B 21.2Q/2S/2U/2W .0B 17.2Q or.0B 17.2S

ETIP1-A

1.0B 21.2Q/2S/2U/2W .0B 16.2U ETP-A






84 (104)







TC1C4 TR3 track 4,8,12,31,35,39






ZDTF;





14 ACTIONS AFTER UPGRADE & POST CONDITIONS

14.1 BSS Integration

After S65 Standalone TCSM3i ETIP1-A implementation for IPPWE (S15/S16/S16.1 TCSM HW) make BSCintegration for upgraded units according BSS integration. The document can be found from NED.

14.2 BSC configuration printout (post-check)

The information about the BSC configurations and conditions are collected.


85 (104)

The checking can be made by using the macro (UPGMAIN.HIT) or manually following the instructions from “BSCconfiguration printout”-document delivered in Release Binder.For macro execution, choose the BSC configuration printout (post) step in BSC ETIP1-A implementation forIP/PWE procedure . Follow then the macro execution according the BSC configuration printout –document.

14.3 Return to the old HW configuration

If return to old HW configuration is needed, follow the instructions in this document in the reverse order. Oractivate fallback build taken before HW upgrade and change cablings according the Cablings instructions forBSC3i which can be found from NED.

15 APPENDIX 1:SAMPLE CREATION OF IP/PW CREATION AND PW TUNNEL

15.1 Create IP/PW first to the TC1C1 track 17 ETIP master locally


Configure locally the first PW interface to ETIP1-A in TC1C1 in track 17 by using local cablea. from back panel with CPCU020 cable connection in ETIP1-A card in

TC1C1 track 17Service Terminal connection to ETIP1-A is available through the back panel. Connect CPCU020 cable(C104887) to the back panel connector 4P with traffic parameters 9600/ Even / 7.Username: rootPassword: root1234

b. from front panel cable connection in ETIP1-A card in TC1C-0 track 7Take a SSH session with a direct Ethernet cable attached into front-panel SFP module. The card defaultaddress is 192.168.1.111/24 and the client must use IP address from 192.168.1.0/24 subnet.



15.1.1 Configure PW_MANA0, PW0 and IP addresses to script file using vi –editor






86 (104)

15.1.2 Configure PW_MANA0, PW0 VLAN’s to script file using vi –editor






15.1.3 Configure the static network routes to script file using vi –editor






15.1.4 Restart the ETIP master unit

lnx-hwapi-tool -f 0

15.1.5 Add Tunnel and PW configuration of first A-interface ETIP master unit:


Create the PW under the tunnel:lnx-pwe-tool c <TCSM pwindex> <TCSM tunnelindex> <ludp> <pudp> <pcm> -p=<TCSM PW name>

Name Value Infopwindex 0-65534 PW indextunnelindex 0-65534 Tunnel idludp 1-65535 Local UDP port


87 (104)

pudp 1-65535 Peer UDP port

pcm 0-8191PCM line number( in TCSM site starting from 0)


example:lnx-pwe-tool a 100 10.16.66.172 -n=ATOETIP2lnx-pwe-tool c 100 100 100 100 12 –p=TCSM323lnx-pwe-tool j 100 ena

15.1.6 Go to MML to check the D-channel state

ZDTF;15.1.7 Take the A-if master TCSM unit to TE-EX ( in TC1C1 track 4)


15.1.8 Connect locally to A-interface ETIP1-A master unit and upload the configuration from ETIP1-Acard to TR3 card:


15.1.9 Take the A-interface master TCSM unit to WO-EX


When the first A-interface master TCSM unit D-channel is in WO-EXconfiguration rest of the TCSM unit configurations can be done by usingMML.

15.2 Create new PSN tunnel (or use the one created to A-interface master)


Name Value Info

unit type






Example:


88 (104)

ZQYA:TCSM,322,A:100:"10.16.66.188":ATOTCSM322:;

15.2.1 Create new PW inside PSN tunnel



Name Value Info








PCM number



JB lenght 1-192




VLAN priority 0-7



Example:ZQYC:TCSM,322,A:100:100:100,100:0::::::TCSM322A:;

15.2.2 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)

Use the QYJ MML command to enable all the PWs in a tunnel.


89 (104)

ZQYJ:ETIP,<unit index>: <tunnel index>:<action>;

Name Value Info

unit type



Example:ZQYJ:TCSM,322,A:100:ENA;


ZQYE:<unit type>,<unit index>:<PW index>:<action>;

Name Value Info

unit type



Example:ZQYE:TCSM,322,A:100:ENA;

15.2.3 Verify information


Name Value Info

unit type






90 (104)

16 APPENDIX 2:SAMPLE CREATION OF IP/PWE AND TUNNEL FOR ETIP AS A-IFTCSM.

16.1 Create IP/PW locally to the A-interface master and redundant ETIP1-A units


16.1.1 Configure locally the first PW interface to ETIP1-A in TC1C0 in track 17 by using local cable

a. from back panel with CPCU020 cable connection in ETIP1-A card inTC1C0 track 17


b. from front panel cable connection in ETIP1-A card in TC1C0 track 17( In use if ETIP1-A )













91 (104)










lnx-hwapi-tool -f 0

16.1.6 Configure locally the redundant ETIP1-A unit for Ater interface PW by using local cableconnection in ETIP1-A card in TC1C0 in track 25

a. from back panel with CPCU020 cable connection in ETIP1-A card inTC1C0 track 25


b. from front panel cable connection in ETIP1-A card in TC1C0 track 25( In use if ETIP1-A )


Username; rootPassword: root1234Modify IP address, VLAN and route use linux vi-editor





92 (104)













vi /opt/etip_tcsm_routes_conf.shroute add -net 10.16.66.160 netmask 255.255.255.248 gw 10.16.66.177route add -net 10.16.66.168 netmask 255.255.255.248 gw 10.16.66.185


lnx-hwapi-tool -f 0

16.2 Add Tunnel and PW configuration of first A-interface ETIP master unit (TC1C0in track 17)


Create the PW under the tunnel:


93 (104)

lnx-pwe-tool c <TCSM pwindex> <TCSM tunnelindex> <ludp> <pudp> <pcm> -p=<TCSM PW name>

Name Value Infopwindex 0-65534 PW indextunnelindex 0-65534 Tunnel idLudp 1-65535 Local UDP portPudp 1-65535 Peer UDP port

Pcm 0-8191PCM line number( in TCSM site starting from 0)


Example:lnx-pwe-tool a 100 10.16.66.172 -n=ATOETIP2lnx-pwe-tool c 100 100 100 100 12 –p=TCSM323lnx-pwe-tool j 100 ena

16.2.1 Go to MML to check the D-channel state

ZDTF;

16.2.2 Take the A-if master TCSM unit to TE-EX (in TC1C0 track 4)


16.2.3 Connect locally to A-interface ETIP1-A master unit and upload the configuration from ETIP1-Acard to TR3 card:


16.2.4 Take the A-interface master TCSM unit to WO-EX


When the first A-interface master TCSM unit D-channel is in WO-EXconfiguration rest of the TCSM unit configurations can be done by usingMML.

16.3 Create new PSN tunnel (or use the one created to A-interface master)


Name Value Info

unit typeType of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i and TCSM


94 (104)

for ETIPs in TCSM3i)unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)




Example:ZQYA:TCSM,322,A:100:"10.16.66.188":ATOTCSM322:;

16.3.1 Create new PW inside PSN tunnel



Name Value Info








PCM number



JB lenght 1-192



ToS field 0-63 IP packet ToS field (same as DSCP) (Optional, default is 0)VLAN priority 0-7 VLAN priority (Optional, if does not set value from IP management is


95 (104)

used instead, if there is no VLAN set in IP management thisparameter will be ignored)


Example:ZQYC:TCSM,322,A:100:100:100,100:0::::::TCSM322A:;

16.3.2 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)


Name Value Info

unit type



Example:ZQYJ:TCSM,322,A:100:ENA;


ZQYE:<unit type>,<unit index>:<PW index>:<action>;Name Value Info

unit type



Example:ZQYE:TCSM,322,A:100:ENA;

16.3.3 Verify information


Name Value Info


96 (104)

unit type





As if now not avilable.

17 APPENDIX 3: INTERNAL PCM USAGE FOR A-INTERFACE

ETIP in TC1C in track 17(protecting ETIP1-A in track 25if equipment protection in use) Internal PCM

TC1C Slot from to0 1 0 0 3

0 2 0 4 7

0 3 0 8 11

0 4 0 12 15

0 5 0 16 19

0 6 0 20 23

0 7 0 24 27

0 8 0 28 31

0 9 0 32 35

0 10 0 36 39

0 11 0 40 43

0 12 0 44 47

0 28 0 48 51

0 29 0 52 55

0 30 0 56 59

0 31 0 60 63

0 32 0 64 67

0 33 0 68 71

0 34 0 72 75

0 35 0 76 79

0 36 0 80 83

0 37 0 84 87

0 38 0 88 91

0 39 0 92 95

1 1 1 0 3

1 2 1 4 7

1 3 1 8 11

1 4 1 12 15

1 5 1 16 19


97 (104)

1 6 1 20 23

1 7 1 24 27

1 8 1 28 31

1 9 1 32 35

1 10 1 36 39

1 11 1 40 43

1 12 1 44 47

1 28 1 48 51

1 29 1 52 55

1 30 1 56 59

1 31 1 60 63

1 32 1 64 67

1 33 1 68 71

1 34 1 72 75

1 35 1 76 79

1 36 1 80 83

1 37 1 84 87

1 38 1 88 91

1 39 1 92 95

2 1 2 0 3

2 2 2 4 7

2 3 2 8 11

2 4 2 12 15

2 5 2 16 19

2 6 2 20 23

2 7 2 24 27

2 8 2 28 31

2 9 2 32 35

2 10 2 36 39

2 11 2 40 43

2 12 2 44 47

2 28 2 48 51

2 29 2 52 55

2 30 2 56 59

2 31 2 60 63

2 32 2 64 67

2 33 2 68 71

2 34 2 72 75

2 35 2 76 79

2 36 2 80 83

2 37 2 84 87

2 38 2 88 91

2 39 2 92 95

3 1 3 0 3

3 2 3 4 7

3 3 3 8 11

3 4 3 12 15


98 (104)

3 5 3 16 19

3 6 3 20 23

3 7 3 24 27

3 8 3 28 31

3 9 3 32 35

3 10 3 36 39

3 11 3 40 43

3 12 3 44 47

3 28 3 48 51

3 29 3 52 55

3 30 3 56 59

3 31 3 60 63

3 32 3 64 67

3 33 3 68 71

3 34 3 72 75

3 35 3 76 79

3 36 3 80 83

3 37 3 84 87

3 38 3 88 91

3 39 3 92 95

4 1 4 0 3

4 2 4 4 7

4 3 4 8 11

4 4 4 12 15

4 5 4 16 19

4 6 4 20 23

4 7 4 24 27

4 8 4 28 31

4 9 4 32 35

4 10 4 36 39

4 11 4 40 43

4 12 4 44 47

4 28 4 48 51

4 29 4 52 55

4 30 4 56 59

4 31 4 60 63

4 32 4 64 67

4 33 4 68 71

4 34 4 72 75

4 35 4 76 79

4 36 4 80 83

4 37 4 84 87

4 38 4 88 91

4 39 4 92 95

5 1 5 0 3

5 2 5 4 7

5 3 5 8 11


99 (104)

5 4 5 12 15

5 5 5 16 19

5 6 5 20 23

5 7 5 24 27

5 8 5 28 31

5 9 5 32 35

5 10 5 36 39

5 11 5 40 43

5 12 5 44 47

5 28 5 48 51

5 29 5 52 55

5 30 5 56 59

5 31 5 60 63

5 32 5 64 67

5 33 5 68 71

5 34 5 72 75

5 35 5 76 79

5 36 5 80 83

5 37 5 84 87

5 38 5 88 91

5 39 5 92 95

18 APPENDIX 4:INTERNAL PCM USAGE FOR A-TER INTERFACE

Working ETIP1-A in TC1C-0 track 13Protecting ETIP1-A in TC1C-1 in track13

TC1C Slot Internal PCM0 1 00 2 10 3 20 4 30 5 40 6 50 7 60 8 70 9 80 10 90 11 100 12 110 28 120 29 13


100 (104)

0 30 140 31 150 32 160 33 170 34 180 35 190 36 200 37 210 38 220 39 231 1 241 2 251 3 261 4 271 5 281 6 291 7 301 8 311 9 321 10 331 11 341 12 351 28 361 29 371 30 381 31 391 32 401 33 411 34 421 35 431 36 441 37 451 38 461 39 472 1 482 2 492 3 502 4 512 5 522 6 532 7 542 8 552 9 562 10 572 11 582 12 59


101 (104)

2 28 602 29 612 30 622 31 632 32 642 33 652 34 662 35 672 36 682 37 692 38 702 39 713 1 723 2 733 3 743 4 753 5 763 6 773 7 783 8 793 9 803 10 813 11 823 12 833 28 843 29 853 30 863 31 873 32 883 33 893 34 903 35 913 36 923 37 933 38 943 39 954 1 964 2 974 3 984 4 994 5 1004 6 1014 7 1024 8 1034 9 1044 10 105


102 (104)

4 11 1064 12 1074 28 1084 29 1094 30 1104 31 1114 32 1124 33 1134 34 1144 35 1154 36 1164 37 1174 38 1184 39 119

19 APPENDIX 5: UPDATING EMBEDDED SOFTWARE OF ETIP1-A

The embedded software is stored in the flash memory of the ETIP1-A plug-in unit and in the OMUcomputer. It is possible to upload newer software build to the ETIP1-A plug-in unit in BSC and inTCSM with the WDJ and WDK MML commands. It is recommended to use the same softwareversion in all the ETIP1-A plug-in units, therefore a software update is necessary when a faulty plug-in unit is replaced with a new one, and the new unit's SW version in the flash memory is differentthan that of the other plug-in units.Compare ETIP eSW versions in the ETIP1-A Plug-in unit:

ZWDK:UT=ETIP,UI=<index>;Compare ETIP eSW versions in the BSC disk with MASHAn service terminal command:

ZMXP:W0-LFILES/LNX*:*If there are differences between existing and newer eSW, a new software(s) must be updated to theflash memory of ETIP1-A.

NOTE! Depending on amount of software modules being to update it might take up to 1 hourper ETIP1-A plug-in unit in BSC site and in TCSM site via LAPD link the update may take 8hours if all working and backup SW’s are updated same time

The software has been divided into two categories: applications and Board Support Package (BSP).BSP consists of three modules:- Kernel = LNX71C02- FPGA = LNXFPG02- Loader = LNXUBO02Application software (APPL) is all other modules listed WDK-command.

The following example steps showing how to update ETIP1-A flash memory in BSC during softwareupdate. If ETIP1-A configured to TCSM unit in WDK and WDJ commands have to be defined"NT=TCSM, NI=<TCSM index>" parameters.

Change ETIP unit to TE-EX state:ZUSC:ETIP,<index>:BL;ZUSC:ETIP,<index>:TE;

Update changed eSW of ETIP unit according above mentioned categories:ZWDJ:UT=ETIP,UI=<index>,SW=FPGA;ZWDJ:UT=ETIP,UI=<index>,SW=KERNEL;ZWDJ:UT=ETIP,UI=<index>,SW=LOADER;ZWDJ:UT=ETIP,UI=<index>,SW=APPL;


103 (104)

Restart ETIP unit and check alarms:ZUSU:ETIP,<index>;ZAHO:ETIP,<index>;

Backup updated FPGA, Kernel and Loader softwares.ZWDJ:UT=ETIP,UI=<index>,SW=BACKUPFPGA,;ZWDJ:UT=ETIP,UI=<index>,SW=BACKUPKERNEL,;ZWDJ:UT=ETIP,UI=<index>,SW=BACKUPLOADER,;

Check that primary and secondary software are corresponding each other.ZWDK:UT=ETIP,UI=<index>;

Change ETIP unit back to WO-EX state.ZUSC:ETIP,<index>:WO;

Repeat same procedure for all other ETIP Units.

If updated ETIP plug in unit is in TCSM, start a remote session with the ZDDT command and run theZUP command.

ZDDT:TCSM,<TCSM index>;ZUP:ET,<ETIP index>;

Disclaimer

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for theuse of Nokia Solutions and Networks customers only for the purposes of the agreement underwhich the document is submitted, and no part of it may be used, reproduced, modified ortransmitted in any form or means without the prior written permission of Nokia Solutions andNetworks. The documentation has been prepared to be used by professional and properlytrained personnel, and the customer assumes full responsibility when using it. Nokia Solutionsand Networks welcomes customer comments as part of the process of continuous developmentand improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity,or performance of the mentioned hardware or software products are given “as is” and all liabilityarising in connection with such hardware or software products shall be defined conclusively andfinally in a separate agreement between Nokia Solutions and Networks and the customer.However, Nokia Solutions and Networks has made all reasonable efforts to ensure that theinstructions contained in the document are adequate and free of material errors and omissions.Nokia Solutions and Networks will, if deemed necessary by Nokia Solutions and Networks,explain issues which may not be covered by the document.

Nokia Solutions and Networks will correct errors in this documentation as soon as possible. INNO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUTNOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESSOPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT ORTHE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

NSN is a trademark of Nokia Solutions and Networks. Nokia is a registered trademark of NokiaCorporation. Other product names mentioned in this document may be trademarks of theirrespective owners, and they are mentioned for identification purposes only.

Standalone TCSM3i ETIP1-A Implementation for IPPWE (S15 TCSM HW)-Ver-1_0

Documents

Transcript of Standalone TCSM3i ETIP1-A Implementation for IPPWE (S15 TCSM HW)-Ver-1_0