STAGEPAS600i Data Sheet€¦ · The Yamaha STAGEPAS 600i shall be a portable PA system that...
Transcript of STAGEPAS600i Data Sheet€¦ · The Yamaha STAGEPAS 600i shall be a portable PA system that...
Technical Data Sheet 1 / 6
Portable PA Systems STAGEPAS600i
Overview
680-watt, portable PA system with 10-channel powered mixer, two
10" speakers, iPod/iPhone USB connection, SPX digital reverbs, an
onboard feedback suppressor and versatile EQ.
Features
• 680W (340W + 340W) power output
• Newly designed high quality speakers (LF:10" woofer/ HF:1.4" voice coil compression driver)
• Detachable 10-channel mixer (4 mono/line + 6 mono / 3 stereo line)
• iPod/ iPhone USB connection
• 1-Knob Master EQ™ with virtual bass boost
• High resolution SPX digital reverbs (4 types, parameter control)
• Onboard feedback suppressor
• Great-sounding 3-band channel EQ
• Switchable stereo/ mono inputs
• Hi-Z (high impedance) inputs
• Phantom power
• Monitor and Subwoofer outputs
• Optional reverb footswitch
Technical Data Sheet 2 / 6
Portable PA Systems STAGEPAS600i
General Specifications
System
System Type Powered mixer with 2 passive speakers
Frequency Range (-10dB) 55Hz-20kHz
Maximum SPL (Measured Peak IEC Noise@1m) 129dB SPL / speaker
Power Consumption 35W (Idle), 100W (1/8 Power)
Power Requirements 100V-240V, 50Hz/60Hz
Dimentions (W×H×D) Speaker: 335mm x 545mm x 319mm (13.2" x 21.5" x 12.6"), Mixer: 348mm x 197mm x 135mm (13.7" x 7.8" x 5.3")
Net Weight 25.4kg / 56lbs (2 x Speaker 10.8kg + Mixer 3.8kg)
Powered Mixer
Mixer Mixing Channels 10
Analog Inputs 4 mono mic/line + 6 mono / 3 stereo line
Digital Inputs USB Audio IN: iPod/iPhone exclusive
Channel EQ 3-band (HIGH Shelving: 8kHz, MID peaking: 2.5kHz, LOW Shelving: 100Hz)
Channel Functions Hi-Z switch: CH4, ST/MONO switch: CH5/6-9/10
Digital Effects SPX digital reverb (4 program, parameter control)
Output Processing Feedback suppressor, 1-Knob Master EQ™
Phantom Power +30V (CH1, 2)
Outputs SPEAKERS OUT (L, R), MONITOR OUT (L/MONO, R), SUBWOOFER OUT (MONO) with auto HPF
Control and Others Reverb foot switch
Built in Amplifiers Power Rating (Dynamic) 680W (340W + 340W)
Power Rating (Continuous) 560W (280W + 280W)
Speaker
Type Two-way bass-relfex speakers
Components LF: 10" (25cm) cone, HF: 1.4" (3.56cm) voice coil compression driver
Coverage Angle 90° x 60°
Floor Monitor Angle 50°
Handle Top x 1
Pole Socket 34.8-35.2mm pole socket with StageLok™
Accessories
Included Accessories Cover panel, Power cord (2m), Speaker cables (6m) x 2, Non-skid pads x 12
Optional Accessories Yamaha BMS10A (mic stand adaptor) for mixer mount, FC5 (footswitch) for reverb ON/OFF
Specifications 1/2
Technical Data Sheet 3 / 6
Portable PA Systems STAGEPAS600i
Analog Input Specifications
Input Terminals MIC/LINE Input Impedance Source ImpedanceInput level
ConnectorSensitivity Nominal Max. before Clip
CH IN 1-2MIC
3kΩ 150 Ω Mics-56 dBu -35 dBu -10 dBu
XLR-3-31LINE -30 dBu -9 dBu +16 dBu
CH IN 3-4
MIC3kΩ 150 Ω Mics
-56 dBu -35 dBu -10 dBuXLR
XLR ComboLINE -30 dBu -9 dBu +16 dBu
MIC 10 kΩ (Hi-Z 1 MΩ)
150 Ω Lines (Hi-Z 10 kΩ)
-50 dBu -29 dBu -4 dBuPhone
LINE -24 dBu -3 dBu +22 dBu
CH IN 5/6 LINE 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone**
CH IN 7/8 LINE 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone**, RCA Pin
CH IN 9/10 LINE 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone**, Stereo Mini
Output Specifications
Output Terminals Output Impedance Load ImpedanceOutput Level
ConnectorNominal Max. before Clip Typ at THD+N 10% Dynamic
SPEAKERS OUT [L,R] <0.1 Ω 4Ω Speakers - - 280 W 340 W Phone**
MONITOR OUT [L,R] 600 Ω 10 kΩ Lines +4 dBu +20 dBu - - Phone**
SUBWOOFER OUT 150 Ω 10 kΩ Lines -3 dBu +17 dBu - - Phone**
Digital Input Specifications
Terminal Format Connector
USB IN iPod, iPhone exclusive USB A type
Specifications 2/2
Technical Data Sheet 4 / 6
Portable PA Systems STAGEPAS600i
Dimensions
Unit: mm (inch)
Mixer Speaker
319
(12.
6) 144
(5.7
)
50°
354
(13.
9)
109 (4.3)96 (3.8)
2 (0.1)
135 (5.3)
335 (13.2)
545
(21.
5)
348
(13.
7)
197 (7.8)Screw holes for the Mic Stand Adapter BMS-10A (optional)
Pole diameter 34.8 - 35.2* Use of the stand should refer to stand
manufacturer’s instructions.
Options
• Mic Stand Adaptor BMS10A
• Foot Switch FC5
Technical Data Sheet 5 / 6
Portable PA Systems STAGEPAS600i
Architectural and Engineering Specifications
The Yamaha STAGEPAS 600i shall be a portable PA system that incorporates a powered mixer with a pair of passive speakers.
The mixer section of the powered mixer shall have 10 analog mixing channels (4 mono microphone/line + 6 mono/3 stereo line) and a digital
USB Audio IN input exclusively for iPad/iPhone. The STAGEPAS 600i shall have 3-band channel EQ (HIGH Shelving at 8kHz, MID peaking at
2.5 kHz, LOW Shelving at 100Hz), a Hi-Z switch on channel 4, ST/MONO switches for channels 5/6 and 7/8 and 9/10, SPX digital reverb with 4
programs and parameter control, a feedback suppressor, 1-Knob Master EQ™, and +30V phantom power on channels 1 and 2. Outputs shall be
SPEAKERS OUT (L and R), MONITOR OUT (L/MONO and R), and SUBWOOFER OUT (MONO) with auto HPF. A Reverb foot switch connector
shall be provided.
The amplifier section of the powered mixer shall have a universal power supply that accepts AC line input from 100V to 240V at 50Hz or 60Hz.
The power output rating shall be 680 watts (340 watts + 340 watts) dynamic, or 560 watts (280 watts + 280 watts) continuous.
The loudspeakers shall incorporate a single 10" cone for the low frequencies and a compression driver with a 1.4" voice coil for the high
frequencies. The loudspeakers shall meet the following performance criteria: Maximum SPL shall be 129dB at 1 meter, frequency response shall
be 55 Hz ~ 20 kHz at 10dB below rated sensitivity, and nominal coverage angle shall be 90° horizontal and 60° vertical. The loudspeaker shall
have a 50° floor monitor angle, a top handle, and a 34.8 ~ 35.2 mm pole socket with StageLok™.
Powered mixer dimensions shall be 348 (W) x 197 (H) x 135 (D) mm. Powered mixer weight shall be no more than 3.8 kg. The dimensions of each
loudspeaker shall be 335 (W) x 545 (H) x 319 (D) mm. The weight of each loudspeaker shall be no more than 10.8 kg. Total PA system weight
shall be 25.4 kg.
Accessories included with the portable PA system shall be: cover panel, power cord (2 meters), 2 speaker cables (6 meters each), 12 non-skid
pads.
Technical Data Sheet 6 / 6
Portable PA Systems STAGEPAS600i
*All information subject to change without notice.*All trademarks and registered trademarks are property of their respective owners.Created in March, 2017
Block Diagrams