SPECIFICATION - 엘레파츠 · 2011-05-23 · Topview 5750 SMD LED IWS-506-RGB-K3 IWS...
Transcript of SPECIFICATION - 엘레파츠 · 2011-05-23 · Topview 5750 SMD LED IWS-506-RGB-K3 IWS...
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
SPECIFICATION
① Product : Topview 5750 SMD LED
② Part No : IWS-506-RGB-K3
③ Customer :
④ Date : 2007. 1. 31 Ver.2.1
Incheon Factory
58B-4L 626-3 Gozan-dong Namdong-gu Incheon-city 405-817 KOREA
Tel: 82-31-814-1972 FAX: 82-31-822-9009
Ochang Factory & Head Office :
363-880, 9-4Block, Ochang Scientific Industrial Complex, 1115-4 Namchon-ri, Oksan-myeon, Chengwon-
gun, Chungbuk 363-911 Korea
URL : www.itswell.com, TEL : int) 82-43-218-1800, FAX.: int) 82-43-218-1805
Proposed By Checked By Checked By Checked By Approval
Checked By Checked By Checked By Checked By Approval
Customer :
Manufacturer : ITSWELL Co., LTD
Comment
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
• RGB 3-chip luminosity Chip LED
• 5.7 x 5.0 x 1.8 mm (L x W x H), 6-pin, small size surface mount type
• Wide Viewing angle
• Long operating life (up to 70,000 hours)
1. Features
• Automotive: Backlight in dashboard and switch
• Lighting device: Indicator, lighting
• Camera flash, Hand Carrier Flash
• General use
2. Applications
Note
1. All dimensions are in millimeters
2. All dimensions without tolerances are for reference only
3. Outline Drawing and Dimension
Unit : mmTolerance : ±0.1mm
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
4. Absolute Maximum Ratings(Ta=25℃)
5. Electro-optical Characteristics(Ta=25℃)
※1 Duty ratio = 1/10, Pulse width = 0.1ms
Parameter SymbolValue
UnitRed Green Blue
Power Dissipation PD 78 90 90 mW
Continuous Forward Current IF 30 30 30 mA
Peak Forward Current ※1 IFP 100 100 100 mA
Reverse Current IZR 100 mA
Operating Temperature Topr -30 ~ 85 ℃
Storage Temperature Tstg -40 ~100 ℃
Soldering Temperature Tsol 260 (5sec) ℃
※2 Forward Voltage has an accuracy of ±0.1V
※3 Dominant wavelength has an accuracy of ±1nm
※4 Luminous Intensity is tested by a tester calibrated by CAS 140B(CIE LED_B) and has an accuracy of 10%
Parameter Symbol Conditions Min. Typ. Max. Unit.
Forward Voltage※2 VF IF = 20mA
Red - 2.0 2.6 V
Green - 3.4 4.0 V
Blue - 3.4 4.0 V
Reverse Current IR VR = 5V Red - - 10 uA
Reverse Voltage VZR IR = 5mAGreen 0.7 - 1.5 V
Blue 0.7 - 1.5 V
Dominant Wavelength※3 WD IF = 20mA
Red 618 - 635 nm
Green 520 - 535 nm
Blue 455 - 475 nm
Luminous Intensity※4 IV IF = 20mA
Red - 500 700 mcd
Green - 900 1300 mcd
Blue - 300 500 mcd
View angle 2θ1/2 IF= 20mA - - 120 - deg
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
5.1 Luminous intensity Rank( mcd, IF = 20mA )
RANK RED GREEN BLUE
J 100 - 150
K 150 - 300 150 - 300
L 300 - 500 300 - 500
M 500 - 700 500 - 700
N 700 - 900
P 900 – 1100
Q 1100 - 1300
5.2 Dominant Wavelength Combination Rank( nm, IF = 20mA )
RANK RED GREEN BLUE
A 618 - 635 520 – 535 455 - 475
RANK RED GREEN BLUE
a 1.8 - 2.6 3.0 – 3.5 3.0 – 3.5
b 3.5 – 4.0 3.5 – 4.0
5.3 Forward Voltage Rank ( V, IF = 20mA )
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
Forward Current vs.Forward Voltage
Forward Current vs.Ambient Temperature
Relative Luminous Intensity vs.Ambient Temperature
Relative Luminous Intensity vs. Forward Current
Relative Intensity vs. Wavelength Radiation Diagram
Rel
ativ
e L
um
ino
uss
ity
(a.u
)
Radiation Angle3090
060 10 0.5
90
1
0.5
Temp=25
IF=20mA
℃
70
20
60
40
30
50
0 10
80
-40 -20 0 20 40 60 800.1
1
10
Rel
itiv
e L
um
ino
us
Inte
nsi
ty
Ambient Temperature( )℃
400 500 600 700 8000
25
50
75
100
Rel
ativ
e In
ten
sity
(%)
Wavelength(nm)
0 20 40 60 80 1000
10
20
30
40
DC
Fo
rwar
d C
urr
ent(
mA
)
Ambient Temperature( )
0 10 20 300
50
100
150
Rel
ativ
e L
um
inous
Inte
nsi
ty(%
)
Forward Current(mA)
℃
6. Typical Characteristics Curves
6.1 Red
1.4 1.6 1.8 2.0 2.2 2.4 2.61
10
100
Fo
rwar
d C
urr
ent(
mA
)
Forward Voltage(V)
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
0 20 40 60 80 1000
10
20
30
40
DC
Fo
rwar
d C
urr
ent(
mA
)Ambient Temperature( )
Forward Current vs.Forward Voltage
Forward Current vs.Ambient Temperature
Relative Luminous Intensity vs.Ambient Temperature
Relative Luminous Intensity vs. Forward Current
Relative Intensity vs. Wavelength Radiation Diagram
6.2 Green
Rel
ativ
e L
um
ino
uss
ity
(a.u
)
Radiation Angle3090
060 10 0.5
90
1
0.5
Temp=25
IF=20mA
℃
70
20
60
40
30
50
0 10
80
℃
℃
0 10 20 300
50
100
150
Rel
ativ
e L
um
inous
Inte
nsi
ty(%
)
Forward Current(mA)
2.0 2.5 3.0 3.5 4.0 4.51
10
100
Fo
rwar
d C
urr
ent(
mA
)
Forward Voltage(V)
0 20 40 60 800.1
1
10
Rel
itiv
e L
um
ino
us
Inte
nsi
ty
Ambient Temperature(℃)℃
400 500 600 700 8000
20
40
60
80
100
Rel
ativ
e In
ten
sity
(%)
Wavelength(nm)
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
0 20 40 60 80 1000
10
20
30
40
DC
Fo
rwar
d C
urr
ent(
mA
)Ambient Temperature( )
Forward Current vs.Forward Voltage
Forward Current vs.Ambient Temperature
Relative Luminous Intensity vs.Ambient Temperature
Relative Luminous Intensity vs. Forward Current
Relative Intensity vs. Wavelength Radiation Diagram
6.3 Blue
Rel
ativ
e L
um
ino
uss
ity
(a.u
)
Radiation Angle3090
060 10 0.5
90
1
0.5
Temp=25
IF=20mA
℃
70
20
60
40
30
50
0 10
80
℃
℃
0 10 20 300
50
100
150
Rel
ativ
e L
um
inous
Inte
nsi
ty(%
)
Forward Current(mA)
0 20 40 60 800.1
1
10
Rel
itiv
e L
um
ino
us
Inte
nsi
ty
Ambient Temperature(℃)℃
300 400 500 600 700 8000
20
40
60
80
100
Rel
ativ
e In
ten
sity
(%)
Peak Wavelength(nm)
2.0 2.5 3.0 3.5 4.0 4.51
10
100
Fo
rwar
d C
urr
ent(
mA
)
Forward Voltage(V)
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
13.0±0.1
7. Dimension of Tape / Reel
7.1 Tape Dimension
7.2 Reel Dimension
14.4±0.1
13.0±0.1
Unit :mm
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
Diameter : 180 mm
Width : 12 mm
5750 ⇒ 1,000 pcs/Reel
Shield Bag(Polyester/Al/LDPE)
1 Reel / Bag ( T = 0.1 mm ) with Silica gel
Maximum 10 Bags / 1Inner Box
5750 ⇒8,000 pcs/ 1 Inner Box
250
220
Wheel
Bake: 60°C, 4hrs
LabelLabel
224
150
226CHIP LED
www.itswell.com
MIN AVG MAX STD
VF[volt]IV[mcd]WD[nm]
Q’ty :
Lot : IWS-506-RGB-K3
yyyy/mm/dd
Unit :mm8. Packing Dimension
Label
RANK #
Al Pack & Reel Label, Box Label (70 × 37)
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
9.1 Soldering Conditions
When soldering Power SMD, Heat may affect the electrical and optical characteristics of the
LEDs.
In soldering, do not stress the lead frame and the resin part under the high temperature.
The silicone part should be protected from mechanical stress or vibration until the Power SMD
return to room temperature after soldering.
▪ Preliminary heating to be at 200℃ max. for 120 Seconds max.
▪ Soldering heat to be at 260℃ max. for 5sec. Max.
▪ For manual Soldering is Not more than 3sec @MAX350℃, under soldering iron
9.2 Storage
Use with 7days after opening packing. Store in 10 to 30 ℃ Power SMD lead frames are
plated silver. The silver surface may be affected by environment which contain corrosive
gases and so on. Please avoid condition which may cause the
Power SMD to corroded, tarnish or discolor.
9.4 Cleaning
Static electricity or surge voltage damages the Power SMD . It is recommended that a
wrist band or an anti-electrostatic glove be used when handling the LEDs.
A tip soldering iron is requested to be grounded. An ionizer should also be installed where risk
of static.
All devices, equipment and machinery must be properly grounded (via 1MΩ). It is
recommended that measures be taken against surge voltage to the equipment that mounts the
Power SMD.
9.3 Static Electricity
Isopropyl Alcohol or Ethylene Alcohol is recommended in 5 minutes at room temperature.
Don’t use unspecified chemical may cause crack or haze on the surface of the epoxy resin.
Before cleaning, a pre-test should be done to confirm whether any damage to the LED will occur.
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
9. Precaution in use
<Recommendable soldering pattern>
Unit: mm
60sec. Max.Above 200℃
Pre-heating
Time (sec.)
Tem
p(
)
℃
120sec Max.
180-200℃1-5℃/sec
1-5℃/sec260℃, 5sec Max
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
10.1 Reliability Test Item
10. Reliability
Test Items Test Conditions Notes
Steady State Operating life 25 ℃ , 30 mA , 500 hr.
High Temperature
Operating Life
Low Temperature
Operating Life
Steady State Operating life
Of High Humidity Heat
Temperature Cycle
ESD
Pressure Cooker Test
85 ℃ , 5 mA, 500 hr.
-30 ℃ , 30 mA, 300 hr.
60 ℃, 90 % RH, 10 mA, 300 hr.
-40℃(30min) → 25(5min.)
→ 100(30min.) → 25(5min.), 100 cycle
HBM, 100pF, 1.5kohm, 3 times
121 ℃, 2 atm., 99.6 % RH
48 hr.
0/32
0/32
0/32
0/32
0/22
0/22
0/22
High Temperature Storage 100 ℃ , 500 hr. 0/32
Low Temperature Storage -40 ℃ , 500 hr. 0/32
Temp. Humidity Storage 60 ℃, 90 % RH, 500 hr. 0/32
Each of RGB
10.2 Criteria for Judging the Damage
* U means the upper limit of specified characteristics, S means initial value.
Luminous Intensity ( IV ) IF =20 mA
Less than 120% of UForward Voltage ( VF ) IF =20 mA
> 70% of S
Reverse Voltage ( VZR ) IR=5 mA
Items Test Conditions Criteria for judgment
Less than 120% of U
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
I W S – 506 – RGB - K3
Company Name, ITSWELL Co., Ltd.
SMD Type Chip LED
Red, Green, Blue Color
5.7mm x 5.0mm, 1.8mmt, 6-Pin
The symbol shown on the page herein to introduce ‘Electro-Optical
Characteristics’. ESD protection for GaP, AlGaAs and SiC is based chips is still
necessary even though they are safe in low static-electric discharge.
Material in AlInGaP, GaP, or/and InGaN based chips are STATIC SENSITIVE
devices. ESD protection has to considered and taken in the initial design stage.
If manual work/process is needed, please ensure the device is well protective
From ESD during all the process.
LED’s ESD Level is ‘Class II’ and the range of forward voltage is 2000V ~ 3999V.
After opening the package, the LED’s should be kept at 30℃, 70%RH or less.
The LEDs must be dip soldered within seven days(168 hours) after opening the moisture-proof packing.
It is better not to use different rank LEDs.
If use mixed rank, could not attain your object for highest quality of products.
11. Part Name Description
13. Attention : Electric Static Discharge (ESD) Protection
KLM AAA aaa
Luminous Intensity Rank (RGB)
Voltage Rank (RGB)
12. Rank Description
Wavelength Rank (RGB)
Code designated by Maker
Topview 5750 SMD LEDIWS-506-RGB-K3
IWS – 506-RGB-K3 Version of 2.0 PAGE : ‹#› / 13
■ Spec. Review History
Review Ver. Date Correction List Etc.
Ver 1.0 2005.12. 27 Establish
Ver 2.0 2006.04.13 SPEC 일부 조정
Ver 2.1 2007.01.31 Iv수정