Spare Parts Catalogue 2011-11 - Americas Technical...

Prismafl ex®

Spare Parts Catalogue 2011-11

Version: Effective date:MDREC-111164 11.0 2011-11-16

Preface iii

Chapter 1 - Exterior, front 1

Air Bubble Detector “ABD” 5Air Bubble Detector Door 5Blood Leak Detector “BLD” 8Blood Pump Rotor 4Bottom Cabinet 3De-aeration Chamber holder 4Dialysate Scale 2Discharger Clip 8Effluent Scale 2Heparin Pump Carrier 10-50ml 6Led Board 5Led Cover 5Left Hook 4O-ring 2-008 Nitrile 8O-ring 2-011 3O-ring 2-029 5Pre Blood Pump Scale 2Replacement Scale 2Right Hook 4Scale Carrying Bar 2Scale Tube Clips 3Scale Warning Label 3Seals Pressure Pod 8Slave Pump Rotors 4Syringe Clip 10ml 6Syringe Clip 20ml 6Syringe Clip 30ml 6Syringe Clip 50ml 7Syringe Clip 50ml - B.B. Perfusor 7Syringe Clip Holder 10-50ml 6Syringe Pump Control Buttons 7Tube Clip Kit 3

Chapter 2 - Exterior, back 9

Back Pocket 10Cord Holder 10Mains Cable Support 10Potential Equlization Conductor kit 10Power Cord, Brazil 11Power Cord, EU, 6A 11

Contentsi

Power Cord, EU 10A 7,5m 11Power Cord, UK 11Power Cord, US 11Pump Crank 10

Chapter 3 - Interior, front 12

Access Pod Assy. 13ARPS Board 19ARPS Pump Assy 18ARPS Tube Assembly 14Backup Battery, 24V 18Barcode Protection 14Barcode Reader 14Battery, 12V 18Blood Pump Assy. 16CD-ROM Player 14CF Upgrade Kit 16Clamp Dampers Kit 21Discharger Clip Board “CF Class” 16Display 19Effluent Pod Assy. 13Ferrite Pinch Valves 21Filter, 130 Micron 18Filter Pod Assy. 13Hall Sensor Container, Blood Pump 16Hall Sensor Container, Slave P umps 20Hand Grip 21Heparin Fixing Block 17Heparin Pump I2C 17Knurled Knob 21Loader Arm 15Loader Board 15Loader Stepper Motor 15LVDS-RX Board 3V3 19LVDS-TX Board 3V3 19Main Switch 17Micro Switch 15O-ring, Pump Shaft 20Pinch Valve 21Pod No 5 Assy. 13Pressure Transducer ARPS 19Retaining Ring WA 12X22X4 20Return Clamp Assy. 20Return Pressure Port 14Return Pressure Port Assy. 13Scraper Ring 15


Slave Pump Stepper Motor 20Speaker and Fan Assembly 17Stepper Motor ARPS 18Syringe Pump, Calcium 17Touch Screen Controller 16

Chapter 4 - Interior, door 22

Battery Backup Kit 27Carrier Board 23Compact Flash for SW 4.00 and above 24Compact Flash SW 3.20 24CPU Battery 24DC Timer 28Door Latch 24Ethernet Board 25Isolated RS232 Board 25Log Book 26LVDS cable for PC-104 Board 9375 26LVDS cable for TX board 26LVDS RX TX Wire 26Memory Card Board 25PC104 Board PCM 9375 23PC Upgrade Kit 23PIB Board 25Power Harness 27Power Supervision Board Kit 26Power Supply 27Power Supply Battery Backup, 24V 27Protective Board 25Remote Alarm Board 28Signal Cable Harness Kit 27SODIMM Ram Memory 256MB 23SODIMM Ram Memory 512MB 23

Chapter 5 - Base 29

Antistatic Twin Wheels 30Brake Foot 30Brake Pedal 30Pneumatic Spring 30

Chapter 6 - Miscellaneous 31

Back Cabinet 36Back Cover for Base Assembly 37Calibration Tube 35Calibration Weight Kit 33Complete Base Assembly 37Empty Crate 37Front Cabinet 36Hexagonal Wrench, 8mm 33

iiHP Holder 32Inspection Tool for Slave Pump Rotor 33Jumper 34Label Canada, Training must be Performed 34Load Unload Tool 32Non Sterile Catheter 35Potential Equalization Conductor 36Preventive Maintenance Kit 35Retaining Ring Mounting Tool 33Slave Pump Centering Tool 33Spare Part Kit for Load Unload Tool 32Sticker Label English 34Support for HP Holder 32Syringe Pump Holder Kit 35Technical Data Card 35Warmer Holder 32Warning Sticker Kit (USA) 34

Chapter 7 - Manuals 38

Operators Manual CD ROW SW 6.xx 39Operators Manual CD SW 5.xx 42Operators Manual CD US SW 5.10 41Operator’s Manual on CD SW 4.xx 44Operator’s Manual SW 4.xx 43Operator’s Manual SW 5.xx 42Operator’s Manual SW 6.xx 39Operator’s Manual US SW 5.10 41Prismaflex Comm. Prog Guide 6.xx 40Prismaflex Service Manual 5.xx 43Prismaflex Service Manual ROW 6.xx 40Prismaflex Service Manual US 5.10 41Service Manual 4.xx 44Service Manual CD ROW SW 5.xx 43Service Manual CD ROW SW 6.xx 40Service Manual CD US 5.10 41Service Manual on CD SW 4.xx 44

Chapter 8 - Software 45

Software 4.10 RoW Kit 47Software 5.10 US upgrade kit (Only for US) 47Software 6.10 upgrade kit 46Software CD with 6.10 46Software CD with SW 4.10 47Software CD with SW 5.10 (Only for US) 46

Index 48


Preface

Included with each spare part are the necessary screws O-rings etc

• Refer to spare part instructions, enclosed to all spare parts were necessary, for correct exchange and configuration of the spare part.

• This Catalogue can be downloaded from the Customer Support site, if you are a registered user: https://customersupport.gambro.com/gambro_its/user/web/login.aspx

• Because of component updates the spare part pictures can differ from what you receive.

•New When this symbol is found next to a component it means it is a new component and/or that it is new in the spare parts catalogue. Sometimes a component has been available some time before the catalogue is updated.

Updated When this symbol is found next to a component it means the component is updated in a way that we belive is important to point out.


1

Chapter 1 - Exterior, front

Return podEffluent pod

Filter podAccess pod

5th pod

Effluent pump

Pre-Blood pumpDialysate pump

Replacement pump


Exterior, front - 2

Effluent ScaleMeasures the weight of the bags hanging from the scale carrying bars.Note! Each of the four scales has its own unique ID on the I2C bus. Scales are not interchangeable!

Order Number: G5042401 (Flintec)Order Number: G5048301 (Dinamica)

Pre Blood Pump ScaleMeasures the weight of the bags hanging from the scale carrying bars.Note! Each of the four scales has its own unique ID on the I2C bus. Scales are not interchangeable!


Dialysate ScaleMeasures the weight of the bags hanging from the scale carrying bars.Note! Each of the four scales has its own unique ID on the I2C bus. Scales are not interchangeable!


Replacement ScaleMeasures the weight of the bags hanging from the scale carrying bars.Note! Each of the four scales has its own unique ID on the I2C bus. Scales are not interchangeable!


Scale Carrying BarScale handle for hanging the bag onto the scale.

Order Number: G5005101


Exterior, front - 3

Scale Warning LabelCaution stickers making the user aware of opening and closing the scale properly.


O-ring 2-011The O-ring prevent liquid and dirt from coming into the machine via the tube clips.


Tube Clip KitThe tube clips are used to guide the tubes from the filter set. All tubes clips are included in this kit including the calcium clip!


Bottom CabinetBottom cover covering the scales.


Scale Tube ClipsThe tube clips are used to guide the tubes from the filter set. Only the two scale tube clips are included in this kit!



Exterior, front - 4

Right HookA useful tool to hang the scale carrying bar and fluid bag onto when attaching lines to a fluid bag.


Left HookA useful tool to hang the scale carrying bar and fluid bag onto when attaching lines to a fluid bag.


De-aeration Chamber holderHolder for the de-aeration chamber.


Slave Pump RotorsThe slave pump rotors circulates the Effluent, Pre Blood, Dialysate and the Replacement fluids.Same component for all 4 slave pumps.- This version comes as a complete unit with the screw compared to the old which was two parts including screw.


Blood Pump RotorCirculates the blood.

This version has improved bearings improving the occlusivity and an improved Pump Crank connection making it easier to manually rotate the rotor.


Updated


Exterior, front - 5

O-ring 2-029Sealing for the ABD housing.


Air Bubble Detector DoorThe lid for the ABD.


Air Bubble Detector “ABD”Detects air in blood, line in position and blood in set (during priming).


Led CoverCover for the led board.

Order number: G5044601

Led BoardAlarm light - green, yellow and red light.



Exterior, front - 6

Syringe Clip 30mlSyringe clip for the syringe pump.






Syringe Clip Holder 10-50mlSyringe clip holder for the syringe pump.


Heparin Pump Carrier 10-50mlHolds the syringe plunger. The carrier is fitted to the load cell of the heparin pump.



Exterior, front - 7

Syringe Clip 50mlSyringe clip for the syringe pump


Syringe Pump Control ButtonsControls the up and down movement of the syringe pump carrier.


Syringe Clip 50ml - B.B. PerfusorSyringe clip for the syringe pump. Works only with SW 6.10 and later softwares.


New


Exterior, front - 8

O-ring 2-008 NitrileSealing for the discharger clip.


Discharger ClipDischarges the filter set from possible electrostatic interference, connects to the discharger clip board.


Blood Leak Detector “BLD”Detects presence of blood in the effluent line.

Updated with ambient light filter.


Seals Pressure PodSeals the space between the pressure pod and the filter set.



9

Chapter 2 - Exterior, back


Exterior, back - 10

Potential Equlization Conductor kitGround connection at the back of the machine.


Mains Cable SupportProtects the mains cable from being accidentally pulled out. The kit includes two sizes.


Back PocketTo put the Operator’s manual in.


Cord HolderHang the power cord on the cord holder when you don’t use the machine.


Pump CrankIn case of a power failure you use the pump crank to return the blood and also to manually operate the pinch valves.



Exterior, back - 11

Power Cord, EU 10A 7,5mMains power cord for UK.


Power Cord, UKMains power cord for UK.


Power Cord, USMains power cord for US.


Power Cord, EU, 6AMains power cord for Europe.


Power Cord, BrazilMains power cord for Brazil


New

New


12

Chapter 3 - Interior, front


Interior, front - 13

Return Pressure Port Assy.Complete assembly including return pressure port.


Access Pod Assy.Complete Access pod assembly.Cable length 30cm.


Filter Pod Assy.Complete Filter pod assembly.Cable length 50cm.


Pod No 5 Assy.Complete Pod No5 assembly.Cable length 70cm.


Effluent Pod Assy.Complete Effluent pod assembly.Cable length 100cm.




ARPS Tube AssemblyComplete silicon tubing including connectors and clamps for the ARPS system.


Barcode ProtectionProtects the bar code reader from liquid and dirt.

Improved material, glass instead of plastic.


Barcode ReaderRecognizes the type of filter set put on the machine.


Return Pressure Port


CD-ROM PlayerThe CD-ROM player is used for software upgrade or change of language. Includes the bracket the player is mounted on and the IDE cable to connect it to the PC-104 board.




Scraper RingAllows the loader to slide smoothly.


Loader BoardControls the loader stepper motor.


Loader Stepper MotorManeuvers the loader arm.


Loader ArmLoader for the filter set.


Micro SwitchThe micro switch detects when the loader is at the end of its travel.




CF Upgrade KitGrounds the filter set. Upgrades a machine from BF to CF. BF (Body Floating) CF (Cardiac Floating). The kit includes the necessary extra cabling.

The CF card was introduced in production on machine PA3075


Hall Sensor Container, Blood PumpDetects proper movement of the blood pump rotor.


Blood Pump Assy.Drive unit for the blood pump rotor.


Discharger Clip Board “CF Class”Grounds the filter set via the discharger clip. CF (Cardiac Floating).


Touch Screen ControllerHandles the information from the touch screen to the PC-104 board.




Syringe Pump, CalciumSyringe Pump, works with all software versions from software version 4.xx.


Heparin Pump I2CSyringe Pump. Works with software versions up to 4.xx.


Main SwitchComplete assembly.


Heparin Fixing BlockThe fixing block is mounted on the syringe pump load cell. On the fixing block the syringe carrier is mounted.

This block fits both types of syringe pumps!


Speaker and Fan AssemblySpeaker and fan assembly as one unit including the metal sheet thay are mounted on.


New



Stepper Motor ARPSStepper motor for the ARPS pump.


ARPS Pump AssyThe pump is used for the ARPS system to adjust the filter pod adjustment and the level in the bubble trap. Comes as a complete assembly including the metal bracket it is mounted on. One pump segment is mounted and one as a spare segment.


Filter, 130 MicronFilters the air too the ARPS system.


Battery, 12VPower to the memory backup keeping treatment data during a shorter power loss.


Backup Battery, 24VPower to the battery backup system keeping the machine running for a period of time without mains power!




LVDS-TX Board 3V3 Transmits the video signal to the display unit.


LVDS-RX Board 3V3Display unit signal receiver.


DisplayComplete display unit including CF card (G5008202) and LVDS cable (G5041101).


ARPS BoardAutomatic Repositioning System board. All pressure transducers and the ARPS valves are connected to this board.


Pressure Transducer ARPSReference pressure meter for the ARPS system.




Return Clamp Assy.Clamps the return blood line.


Retaining Ring WA 12X22X4Stops liquid and dirt from coming into the machine via the slave pump shaft.


O-ring, Pump ShaftSupport for the rotor.


Hall Sensor Container, Slave P umpsDetects proper movement of the slave pump rotors.


Slave Pump Stepper MotorThe same stepper motor is used for:Effluent, Pre blood, Dialysate and the Replacement pump. The I2C bus ID is unique to each motors position but it can be configured using jumpers on the integrated circuit board of each motor.




Clamp Dampers KitReduces the vibration from the clamp unit.


Pinch ValveThe pinch valves makes it possible to run the treatment with pre or post dilution.


Ferrite Pinch ValvesFerrite for the Pinch Valves cabling.


Knurled KnobUsed to secure components inside the machine.


Hand GripUsed to secure components inside the machine.



22

Chapter 4 - Interior, door


Interior, door - 23

PC Upgrade KitNew PC-104 board requires software 4.xx or higher. It includes, SODIMM, Copper tape, Ferrite, adaptor for old Bar code reader, compact flash, Remote alarm board and LVDS cable for new PC board vs old display. PC board introduced in prod. from PA5858 and the new Display type on PA4532 with exception for PA4528, PA4534, PA4537, PA4541, PA4551, PA4555, PA4587, PA4666.Order Number: G5047803

PC104 Board PCM 9375Control system CPU. The new PC board was introduced in production on machine serial number PA5858.

This board requires software 4.xx or higher!


Carrier BoardInterface board between the PC-104 board and all other slave boards and devices in the machine.


SODIMM Ram Memory 256MBInternal memory for the PC-104 board (PCM-5824).This memory can’t be used on the new PC-board, PCM-9375.

Order No. G5002102

SODIMM Ram Memory 512MBInternal memory for the PC-104 board (PCM-9375).This memory can’t be used on the old PC-board, PCM-5824.

Order No. G5044101


Interior, door - 24

CPU Battery3V Lithium battery for the BIOS on the old PC-board (PCM-5824). Note! Delivered in a pack including 20pcs.


Compact Flash for SW 4.00 and aboveSituated on the PCM-5824/PCM-9375 board and storesthe machines software.

Note! Empty at delivery! Requires a software download by booting and downloading the software from the CD.


Compact Flash SW 3.20Situated on the PCM-5824 board and stores the machines software.Note! This Compact Flash contains specific Prismaflex software. A standard compact flash without the correct specification of software cannot be used with the Prismaflex machine.


Door LatchLocks the door to the cabinet.



Interior, door - 25

Ethernet BoardEnables external Ethernet communication with the machine.


Memory Card BoardTreatment data can be saved on a technical data card. Technical Data Card Order Number: G5000501.


Isolated RS232 BoardEnables external serial data communication with the machine.


PIB BoardPeripheral Interface Board (PIB).Contains the circuitry and connections for the ABD, Venous Clamp, BLD and the Pinch Valves.

Order Number:G5007001

Protective BoardProtection CPU to monitor all safety systems in the Prismaflex.



Interior, door - 26

LVDS RX TX WireCable for the video signal.For use with old Display unit and old PC104 board. Old display unit is installed on machines prior to PA4532. Old PC board is obsolete and has been withdrawn. See PC-upgrade kit G5047803


LVDS cable for TX boardCable for the video signal. For use with new Display unit and old PC104 board New display unit was introduced in production on PA4532, with exceptions for PA4534, PA4537, PA4541, PA4551, PA4555, PA4587, and PA4666. New PC-board is installed on machines from PA5858.Order Number: G5041101

Power Supervision Board KitSupervises the incoming power and alarms in case of a power failure.


LVDS cable for PC-104 Board 9375Cable for the video signal. For use with new Display unit and new PC104 board. Old display unit is installed on machines prior to PA4532. New PC-board is installed on machines from PA5858.


Log BookWhen repairing or servicing the machine, write down every action taken in the Prismaflex log book..Order Number: G5008301


Interior, door - 27

Power SupplySupplies a range of DC voltages to the machine.


Power Supply Battery Backup, 24VSupplies a range of DC voltages to the machine. If a power failure might occur the machine continues to run if the machine is equipped with this power supply together with the 24V battery and software 5.00


Power HarnessCable harness distributing power to the machine from the power supply. For CF and BF machines, one connector will not be used on BF machines.


Signal Cable Harness KitHarness connecting the components in the door to the components in the machine.


Battery Backup KitThis kit includes all hardware needed to upgrade a machine to battery backup. Requires at least software 5.xx.

Includes:Power supply battery backup (G5008702), batteries, cables etc.



Interior, door - 28

DC TimerCounts the machines running hours.


Remote Alarm BoardFor use with external alarms.



29

Chapter 5 - Base


Base - 30

Brake PedalManeuvers the brake feet.This is an improved version with a hole at the bottom as shown in the picture. The reason for the hole is to let out debris which could affect the brake/un-brake mechanism negatively! The new version has order number G5007802.


Brake FootStops the machine from moving.


Antistatic Twin WheelsWheels for the machine.


Pneumatic SpringKeeps the break pedal in its position. This version has an improved sealing compared to the previous spring. A spacer is also included in this version (Not shown in the picture) which makes the open closed position more distinct, the spacer is mounted between the base of the machine and the spring.



31

Chapter 6 - Miscellaneous


Miscellaneous - 32

Support for HP HolderThis is the part of the HP holder which is screwed to the side of the machine. It is included in the HP holder kit, G5040101.


HP HolderHP holder kit to run Hemo Perfusion. The kit includes the support for the holder, G5040601.


Spare Part Kit for Load Unload ToolIncludes; Two adjustable feet’s, Locking key for the feet’s, Four knobs (M6x30), Two rubber feet’s and two snap rings. Order Number: G5040201

Warmer HolderHolder for Gambro approved blood warmers.


Load Unload ToolTo load and unload the Prismaflex in and out of e.g. a car.


No Picture!


Miscellaneous - 33

Inspection Tool for Slave Pump RotorTool to check the occlusivity of a slave pump rotor.


Calibration Weight KitUsed to Calibrate the machines heparin pump and all scales.

The calibration weight can be stored inside the base of the machine. A kit allowing the calibration weight to be placed /stand inside the base of the Prismaflex is included.


Slave Pump Centering ToolUse this tool to center the slave pump in relation to the pump raceway.


Retaining Ring Mounting ToolUse this tool when mounting the scraper ring (G5004501).


Hexagonal Wrench, 8mmFor technical staff to open the Prismaflex door.



Miscellaneous - 34

Label Canada, Training must be PerformedLabel says; Individuals operating the Prismaflex System must be trainedprior to use by authorized Gambro personnel or the Facility’smedical personnel trained by Gambro.


Warning Sticker Kit (USA)Label says;For use with paitients weighing less than 20 kilograms an independent , higher accuracy weight measurment device must be used to verify the correctness of weight loss during treatment.


Sticker Label EnglishStickers explaining the different components on the front of the machine.

Order Number: G5032201No Picture!

JumperAdditional jumpers for e.g. the modification message 008

Order Number: 100202167

New

New


Miscellaneous - 35

Preventive Maintenance KitFor yearly maintenance of the machine.

Includes: PC-104 battery -both for new and old PC-104 board, dampers for the blood pump and slave pumps, pump segment for the ARPS pump + filter and sealing cons for the pressure pods.Order Number: G5010004

Non Sterile CatheterFor use when running a simulated treatment, with this the pressures will automatically be correct.


Not for human use!

Calibration TubeThis is a calibration tube with which you can calibrate all pressure sensors at once.


Not for human use!

Technical Data CardTechnical data can be downloaded to this card from the machine.Note! The card must be inserted in the machine before the machine is powered on.


Syringe Pump Holder KitRepair kit for the front panel in case the supports for the syringe pump is broken.



Miscellaneous - 36

Front CabinetExcept for the front it includes the display frame, sealings, hall sensors and screws. Comes as seen in the picture!


Back CabinetExcept for the back it includes the sealings, handles and screws. Comes as seen in the picture!


Potential Equalization ConductorExternal cable for connection between machine and common ground.

Order Number: K24670001

New

New


Miscellaneous - 37

Back Cover for Base AssemblyComplete assembly including brake mechanism and back cover.


Complete Base AssemblyComplete assembly including brake mechanism and back cover.


Empty CrateFor long distant transportation of the machine. By Truck or Air plane. The crate is approved for both vertical and horizontal transport.


New

New


38

Chapter 7 - Manuals


Manuals - 39

G5036003 Prismaflex op man 6xxG5036103 Prismaflex op man FR 6xxG5036203 Prismaflex op man DE 6xxG5036303 Prismaflex op man IT 6xxG5036403 Prismaflex op man PT 6xxG5036503 Prismaflex op man NL 6xxG5036603 Prismaflex op man SV 6xxG5036703 Prismaflex op man NO 6xxG5036803 Prismaflex op man DA 6xxG5036903 Prismaflex op man ES 6xxG5037003 Prismaflex op man FI 6xxG5037103 Prismaflex op man EL 6xxG5037203 Prismaflex op man PL 6xxG5037303 Prismaflex op man TR 6xxG5037403 Prismaflex op man CS 6xxG5037503 Prismaflex op man ET 6xxG5037603 Prismaflex op man LT 6xxG5037703 Prismaflex op man LV 6xxG5037803 Prismaflex op man RU 6xxG5037903 Prismaflex op man SK 6xxG5038003 Prismaflex op man SL 6xxG5038103 Prismaflex op man ZHCN 6xxG5038203 Prismaflex op man KO 6xxG5038403 Prismaflex op man ZHTW 6xxG5038503 Prismaflex op man HU 6xxG5038603 Prismaflex op man RO 6xx

Operator’s Manual SW 6.xxOperating instructions for the operator. Printed!Note, You can also download these as PDF’s from the Customer Support site!

Operators Manual CD ROW SW 6.xxAll language versions on a CD as *.PDF files


New

New


Manuals - 40

Prismaflex Comm. Prog Guide 6.xxAbout external communication. Handbook for how to receive data from the Prismaflex Ethernet and RS-232 port in order to transmit data to a Patient data management systems (PDMS). Adapting the PDMS system according to software 6.10 makes the system compatible with all softwares back to sofware version 3.20. Note! This handbook can only be ordered after an agreement is signed and a copy has been e-mailed to customer support. [email protected] See service newsletter General Information 006 for more details!


Service Manual CD ROW SW 6.xxThe service guide for the technician on a CD as a *.PDF file.


Prismaflex Service Manual ROW 6.xxThe service guide for the technician. Printed! Note, You can also download the PDF from the Customer Support site!


New

New

New


Manuals - 41

Service Manual CD US 5.10The service guide for the technician on a CD as a *.PDF file.


Prismaflex Service Manual US 5.10The service guide for the technician. Printed! Note, You can also download the PDF from the Customer Support site!


Operator’s Manual US SW 5.10Operating instructions for the operator. Printed!Note, You can also download these as PDF’s from the Customer Support site!


Operators Manual CD US SW 5.10All language versions on a CD as *.PDF files


New

New

New

New


Manuals - 42

Operators Manual CD SW 5.xxAll language versions on a CD as *.PDF files



G5036002 Prismaflex Op Manual EN 5xxG5036102 Prismaflex Op Man FR 5xxG5036202 Prismaflex Op Man DE 5xxG5036302 Prismaflex Op Man IT 5xxG5036402 Prismaflex Op Man PT 5xxG5036502 Prismaflex Op Man NL 5xxG5036602 Prismaflex Op Man SV 5xxG5036702 Prismaflex Op Man NO 5xxG5036802 Prismaflex Op Man DA 5xxG5036902 Prismaflex Op Man ES 5xxG5037002 Prismaflex Op Man FI 5xxG5037102 Prismaflex Op Man EL 5xxG5037202 Prismaflex Op Man PL 5xxG5037302 Prismaflex Op Man TR 5xxG5037502 Prismaflex Op Man ET 5xxG5037602 Prismaflex Op Man LT 5xxG5037702 Prismaflex Op Man LV 5xxG5037802 Prismaflex Op Man RU 5xxG5038002 Prismaflex Op Man SL 5xxG5038202 Prismaflex Op Man KO 5xxG5038402 Prismaflex Op Man Trad Chin 5xxG5038502 Prismaflex Op Man HU 5xxG5038602 Prismaflex Op Man RO 5xx


Manuals - 43

Service Manual CD ROW SW 5.xxThe service guide for the technician on a CD as a *.PDF file.


Prismaflex Service Manual 5.xxThe service guide for the technician. Printed! Note, You can also download the PDF from the Customer Support site!



G5036001 Operator Manual Eng 4.xx-CRRT, TPE, HPG5036101 Operator Manual Fre 4.xx-CRRT, TPE, HPG5036201 Operator Manual Ger 4.xx-CRRT, TPE, HPG5036301 Operator Manual Ita 4.xx-CRRT, TPE, HPG5036401 Operator Manual Por 4.xx-CRRT, TPE, HPG5036501 Operator Manual Dut 4.xx-CRRT, TPE, HPG5036601 Operator Manual Swe 4.xx CRRT, TPE, HPG5036701 Operator Manual Nor 4.xx-CRRT, TPE, HPG5036801 Operator Manual Dan 4.xx-CRRT, TPE, HPG5036901 Operator Manual Spa 4.xx-CRRT, TPE, HPG5037001 Operator Manual Fin 4.xx-CRRT, TPE, HPG5037101 Operator Manual Gre 4.xx-CRRT, TPE, HPG5037201 Operator Manual Pol 4.xx-CRRT, TPE, HPG5037301 Operator Manual Tur 4.xx-CRRT, TPE, HPG5037501 Operator Manual Est 4.xx-CRRT, TPE, HPG5037601 Operator Manual Lit 4.xx - CRRT, TPE, HPG5037701 Operator Manual Lav 4.xx-CRRT, TPE, HPG5037801 Operator Manual Rus 4.xx-CRRT, TPE, HPG5038201 Operator Manual Kor 4.xx-CRRT, TPE, HPG5039906 Operator Manual China 4.xx


Manuals - 44

Operator’s Manual on CD SW 4.xxAll language versions on a CD as *.PDF files.

G5040702 Operators Manual 4.00 on CD All therapiesG5040801 Operators Manual 4.00 on CD US

Service Manual on CD SW 4.xxThe service guide for the technician on a CD as a *.PDF file.

G5008605 Service Manual 4.00 on CD CRRT+TPE+HP

Service Manual 4.xxThe service guide for the technician. Printed! Note, You can also download the PDF from the Customer Support site!

G5005204 Service Manual SW 4.00 ROW


45

Chapter 8 - Software


Software - 46

Software CD with 6.10Software for the Prismaflex machine. Can be used to update the machine to 6.10 software from any earlier software revision.

Note! Software 6.10 requires at least 256MB RAM and Compact Flash memory. It also requires the new Syringe Pump (G5043901). The new syringe pump is introduced in production from PA6561 on machines delivered with Software 4.xx, 5.xx and 6.xx

The software can also be download from the Customer Support site!Order Number: G5001809

Software CD with SW 5.10 (Only for US)Software for the Prismaflex machine. Can be used to update the machine to 5.10 software from any earlier software revision.

Note! Software 5.00 requires at least 256MB RAM and Compact Flash memory. It also requires the new Syringe Pump (G5043901). The new syringe pump is introduced in production from PA6561 on machines delivered with Software 4.xx, 5.xx and 6.xx

The software can also be download from the Customer Support site!


Software 6.10 upgrade kitSoftware and hardware (Syringe pump, Calcium Clip, RAM memory, CF card) to run 6.10. Can be used to update the machine to 6.10 software from any earlier software revision.

The new syringe pump is introduced in production from PA6561 on machines delivered with Software 4.xx, 5.xx and 6.xx


New

New

New


Software - 47

Software 5.10 US upgrade kit (Only for US)Software and hardware (Syringe pump, Calcium Clip, RAM memory, CF card) to run 6.10. Can be used to update the machine to 6.10 software from any earlier software revision.

The new syringe pump is introduced in production from PA6561 on machines delivered with Software 4.xx, 5.xx and 6.xx


New

Software 4.10 RoW KitSoftware and hardware (Tube Clips). Can be used to update the machine to 4.10 software from any earlier software revision.


Software CD with SW 4.10Software for the Prismaflex machine. Can be used to update the machine to 4.10 software from any earlier software revision.



Index - 48

SymbolsG5000101 33G5000201 35G5000301 33G5000401 33G5000501 35G5000601 33G5000701 32G5000801 28G5000901 14G5001001 30G5001201 16G5001301 21G5001401 3G5001501 30G5001601 5G5001701 19G5001805 46G5002001 19G5002102 23G5002201 15G5002301 32G5002404 24G5002406 24G5002501 20G5002601 25G5002802 5G5002901 8G5003101 25G5003201 21G5003303 8G5003402 13G5003601 20G5003701 15G5003901 10G5004002 14G5004101 21G5004201 16G5004301 21G5004401 20G5004501 15G5004601 25G5004702 20

G5004802 13G5005001 16G5005101 2G5005204 44G5005205 43G5005206 40G5005301 8G5005402 5G5005502 17G5005602 15G5005703 4G5005902 14G5006001 8G5006101 4G5006202 18G5006401 18G5006501 19G5006601 13G5006701 5G5006801 20G5006901 19G5007001 25G5007101 23G5007201 25G5007401 4G5007501 4G5007603 3G5007701 35G5007802 30G5008001 15G5008102 26G5008202 16G5008301 26G5008401 24G5008605 44G5008606 43G5008607 40G5008701 27G5008702 27G5008802 28G5009001 18G5009501 10G5009601 10G5009702 30

Index


Index - 49

G5009802 13G5009902 13G5010004 35G5010201 7G5010401 37G5010801 18G5010901 11G5011001 11G5015006 40G5022801 10G5029101 6G5029202 6G5029301 6G5029402 6G5029501 6G5029602 7G5032201 34G5034701 34G5034901 16G5035004 41G5035804 17G5035903 41G5036001 43G5036002 42G5036003 39G5036101 43G5036102 42G5036103 39G5036201 43G5036202 42G5036203 39G5036301 43G5036302 42G5036303 39G5036401 43G5036402 42G5036403 39G5036501 43G5036502 42G5036503 39G5036601 43G5036602 42G5036603 39G5036701 43G5036702 42G5036703 39G5036801 43G5036802 42G5036803 39

G5036901 43G5036902 42G5036903 39G5037001 43G5037002 42G5037003 39G5037101 43G5037102 42G5037103 39G5037201 43G5037202 42G5037203 39G5037301 43G5037302 42G5037303 39G5037403 39G5037501 43G5037502 42G5037503 39G5037601 43G5037602 42G5037603 39G5037701 43G5037702 42G5037703 39G5037801 43G5037802 42G5037803 39G5037903 39G5038002 42G5038003 39G5038103 39G5038201 43G5038202 42G5038203 39G5038402 42G5038403 39G5038502 42G5038503 39G5038602 42G5038603 39G5039903 41G5039906 43G5040101 32G5040201 32G5040404 47G5040503 47G5040601 32G5040703 42


Index - 50

G5040704 39G5040802 41G5040901 14G5041101 26G5041304 19G5041401 37G5041501 34G5041601 3G5041701 33G5042101 3G5042201 27G5042302 17G5042401 2G5042501 2G5042601 2G5042701 2G5043101 17G5043201 24G5043401 27G5043501 18G5043601 27G5043701 11G5043901 17G5044001 23G5044101 23G5044201 36G5044301 36G5044501 37G5044601 5G5044701 14G5047401 26G5047501 4G5047803 23G5048001 47G5048102 26G5048201 35G5048301 2G5048401 2G5048501 2G5048601 2G5048801 3G5049101 21G5049201 11G5049401 11G5049601 7G5049701 10G5050401 46100202167 34

AAccess Pod Assy. 13Air Bubble Detector “ABD” 5Air Bubble Detector Door 5Antistatic Twin Wheels 30ARPS Pump Assy 18ARPS Tube Assembly 14

BBack Cabinet 36Back Cover for Base Assembly 37Backup Battery, 24V 18Barcode Protection 14Barcode Reader 14Battery, 12V 18Battery Backup Kit 27Blood Leak Detector “BLD” 8Blood Pump Assy. 16Blood Pump Rotor 4Brake Foot 30Brake Pedal 30

CCalibration Tube 35Calibration Weight Kit 33Carrier Board 23CD-ROM Player 14CF Upgrade Kit 16Clamp Dampers Kit 21Compact Flash for SW 4.00 and above 24Compact Flash SW 3.20 24Complete Base Assembly 37Cord Holder 10CPU Battery 24

DDC Timer 28De-aeration Chamber holder 4Dialysate Scale 2Discharger Clip 8Discharger Clip Board 16Display 19Door Latch 24


Index - 51

EEffluent Pod Assy. 13Effluent Scale 2Empty Crate 37Ethernet Board 25

FFilter, 130 Micron 18Filter Pod Assy. 13Front Cabinet 36

GG5015003 40

HHall Sensor Container, Blood Pump 16Hall Sensor Container, Slave pumps 20Hand Grip 21Heparin Fixing Block 17Heparin Pump Carrier 10-50ml 6Heparin Pump I2C 17Hexagonal Wrench, 8mm 33HP Holder 32

IInspection Tool for Slave Pump Rotor 33Isolated RS232 Board 25

JJumper 34

KK24670001 36Knurled Knob 21

LLabel Canada, Training must be Performed 34Led Board 5Led Cover 5Left Hook 4Loader Arm 15Loader Board 15Loader Stepper Motor 15Load Unload Tool 32Log Book 26

LVDS cable for PC-104 Board 9375 26LVDS cable for TX board 26LVDS-RX Board 3V3 19LVDS RX TX Wire 26LVDS-TX Board 3V3 19

MMains Cable Support 10Memory Card Board 25Micro Switch 15Motor Stepper 18

NNon Sterile Catheter 35

OOperators Manual CD ROW SW 6.xx 39Operators Manual CD SW 5.xx 42Operator’s Manual on CD SW 4.xx 44Operator’s Manual SW 4.xx 43Operator’s Manual SW 5.xx 42Operator’s Manual SW 6.xx 39O-ring 2-008 Nitrile 8O-ring 2-011 3O-ring 2-029 5O-ring, Pump Shaft 20

PPC 104 Board 23PC104 Board PCM 9375 23PIB Board 25Pinch Valve 21Pneumatic Spring 30Pod No 5 Assy. 13Potential Equalization Conductor 36Potential Equlization Conductor kit 10Power Cord, Brazil 11Power Cord, EU, 6A 11Power Cord, EU 10A 7,5m 11Power Cord, UK 11Power Cord, US 11Power Harness 27Power Supervision Board Kit 26Power Supply 27Power Supply Battery Backup, 24V 27Pre Blood Pump Scale 2Pressure Transducer ARPS 19


Index - 52

Preventive Maintenance Kit 35Prismaflex Comm. Prog Guide 6.xx 40Prismaflex Service Manual 5.xx 43Prismaflex Service Manual ROW 6.xx 40Protective Board 25Pump Crank 10

RRemote Alarm Board 28Replacement Scale 2Retaining Ring Mounting Tool 33Retaining Ring WA 12X22X4 20Return Clamp Assy. 20Return Pressure Port 14Return Pressure Port Assy. 13Right Hook 4

SScale Carrying Bar 2Scale Tube Clips 3Scale Warning Labels 3Scraper Ring 15Seals Pressure Pod 8Service Manual 4.xx 44Service Manual CD ROW SW 6.xx 41Service Manual on CD SW 4.xx 44Signal Cable Harness Kit 27Slave Pump Centering Tool 33Slave Pump Rotors 4Slave Pump Stepper Motor 20SODIMM Ram Memory 256MB 23SODIMM Ram Memory 512MB 23Software 5.10 US upgrade kit 47Software 6.10 upgrade kit 46Software CD with 6.10 46Software CD with SW 4.10 47Software CD with SW 5.10 46Spare Part Kit for Load Unload Tool 32Speaker and Fan Assembly 17Sticker Label English 34Support for HP Holder 32Syringe Clip 10ml 6Syringe Clip 20ml 6Syringe Clip 30ml 6Syringe Clip 50ml 7Syringe Clip 50ml - B.B. Perfusor 7Syringe Clip Holder 10-50ml 6Syringe Pump, Calcium 17

Syringe Pump Control Buttons 7Syringe Pump Holder Kit 35

TTechnical Data Card 35Touch Screen Controller 16Tube Clip Kit 3

WWarmer Holder 32Warning Sticker Kit (USA) 34


This page has been left blank intentionally

53


Gambro Lundia ABBox 10101, LundSE-220 10 SwedenTel +46 46 16 90 00Fax +46 46 16 96 96www.gambro.com


http:\\www.gambro.com

SIGNATURE PAGE This document has been electronically signed by: Date (UTC) UserId UserName

Justification

Justification

Justification

Justification

Justification

Justification

2011-11-16 09:17:14 sesose Severson Sofia

CN Version - Approved


Spare Parts Catalogue 2011-11 - Americas Technical...

Documents

Transcript of Spare Parts Catalogue 2011-11 - Americas Technical...