SP04EAO Modulo Analogo CIMON
-
Upload
carlos-edu -
Category
Documents
-
view
230 -
download
0
Transcript of SP04EAO Modulo Analogo CIMON
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 1/17
www.cimon.com
PLC-S Analog modules
CM3-SP04EAO
CM3-SP04EAACM3-SP04EAM
CM3-SP04EOAI
CM3-SP04EOAV
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 2/17
2 3
MEMO
Caution
To use this product safely please read the following
instructions
The power must be off whenever you are in contact with the product.
Read and understand the following technical information about the
product.
For your safety only a qualied electrician should work on this product.
1.
2.
3.
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 3/17
4 5
General Specifications
Items Specication Standards
Ambient Temp. -10°C~70°C -
Storage Temp. -25°C~80°C -
Ambient Humidity 5~95%RH, (Non-condensing) -
Storage Humidity 5~95%RH, (Non-condensing) -
Vibration
For discontinuous vibration
IEC 61131-2
Frequency Acceleration Amplitude Times10≤f<57Hz - 0.075mm
X,Y,Z
Each direction,
10 times
57≤f≤150Hz 9.8m/s2{1G} -
Contionuous vibration
Frequency Acceleration Amplitude
10≤f<57Hz - 0.035mm
57≤f≤150Hz 4.9m/s2{1G} -
Shocks
· Max. impact acceleration: 147m/S2(15G)
· Authorized time : 11ms
· Pulse wave : Sign half-wave pulse (3 times each in X, Y, Z)
IEC 61131-2
Noise
Square waveimpulse noise
± 2,000V CIMON standard
Electrostaticdischarge
Voltage : 4kV (contact discharging)IEC 61131-2
IEC 1000-2
Radiatedelectromagnetic
eld noise27~500 MHz,10V/m
IEC 61131-2
IEC 1000-4-3
Fast TransientBurst noise
Power module
Digital I/O(24V or more)
Digital I/O(lessthan 24V)
Analog I/OComm. interface IEC 61131-2
IEC 1000-4-4
2 kV 2 kV 0.25 kV
Voltage 2 kV/1min 0.5 kV/1min
Ambientconditions
No corrosive gas or dust
Cooling type Natural air cooling
PLC-S Analog Output (Specications)
Items SP04EAA SP04EOAV SP04EOAI
Analog Output point 2 points 4 points
Analog Output
Voltage: 0V~+5V, 1V~+5V,0V~+10V, -10V~+10V
Current : 0~20mA,4~20mA
0V ~ +10V.-10V ~ 10V
(switch mode)4~20mA
Output setting method Setting by CICONSwitch OFF : 0V~10VSwitch ON :-10~10V
CICON settingNot possible
Digital Input
14bit, 0~16000
16bit, 0~64000Setting by CICON
14bit, 0~16000
Accuracy ± 0.1% (Full Scale)
Conversion velocity 10ms
Absolute Max. Output± 12V24mA
± 12V ± 24mA
Insulation method Photo Coupler between Input terminal and PLC
Power supply External DC 24V
I/O occupation 16 points
I/O Terminal 12points Terminal 8points Terminal
Consump-tion
current(mA)
Internal @DC3.3V, 15mA @DC3.3V, 15mA @DC3.3V, 15mA
External @DC24V, 70mA @DC24V, 60mA @DC24V, 70mA
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 4/17
6 7
PLC-S Analog Input (Specifications)
Analog Mux Specifications (SP04EAM)
Items CM3-SP04EAO CM3-SP04EAA
Analog Input point 4 points 2 points
Analog InputVoltage: 0V~+5V, 1V~+5V, 0V~+10V, -10V~+10V
Current : 0~20mA, 4~20mA
Resolution 14bit, 0~1600014bit, 0~1600016bit, 0~64000
Setting by CICON
Accuracy ± 0.1%(Full Scale)
Conversion speed 2.1ms / 1ch
Absolute Max. input Voltage: ±12VCurrent: ±25mA
±12V±25mA
InsulationPhoto-coupler insulation between input terminal and PLC
(No insulation between channels)
I/O points occupied 16 points
Power Supply External DC 24V
Connection Terminal 12 points Terminal Block
Consumptioncurrent (mA)
Inner @DC3.3V, 15mA @DC3.3V, 15mA
External @DC24V, 60mA @DC24V, 70mA
Items Standard
Analog Input 4 Channels / 1 Module
Analog Input Voltage, RTD sensor, TC sensor
Relay
Max/Min ON TIMEMin. 0.1 sec / Max. 1000.0 sec
Insulation Method Relay
I/O points occupied 16 points
Number of Ports Input 12ports / Output 3ports
Relay Life Expectancy Number of Operation of 108
Features of Analog Module
CM3-SP04EAO is Analog Input module which has 4CH voltage/current Input.CM3-SP04EOAV is Analog Output module which has 4CH voltage output (-10~10V, 0~10V).CM3-SP04EOAI is Analog Output module which has 4CH current output (4~20mA).CM3-SP04EAA is Analog Input and Output mixed module which has 2CH voltage/current input and 2CH voltage/current output.
DA conversion module converts digital value, 16bit binary data (data: 14bit) from PLCCPU, into analog signal (voltage or current output). It converts digital value 0~16000(-8000~8000) / 0~64000(-32000~32000) to analog value 0~20mA, 4~20mA,-10~10V, 0~5V, 0V~10V, 1~5V.
AD conversion module converts input Max. and Min value into 0~16000(-8000~8000).If input value gets out of the range, it converts into -192~16191(8192~8191). If valuegets out of this, -192~16191(-8192~8191) is xed.
There are two AD conversion methods :1. Average processing 2. Sampling processing
Through “Hold Clear” function, DA module can output offset value (4mA, -10V) whenRUN mode changes to STOP mode or maintain output value being with RUN mode.
Channel that converting is prohibited will output the minimum value of each output mode.(0mA, 4mA, -10V, 0V, 1V)
User can set up Offset/Gain value through CICON Ladder Program.
Maximum 11 analog modules can be installed in one slot.
Normal status: LED On, Error status: LED blinking by 0.5sec interval.
1)
2)
3)
4)
5)
6)
7)
8)
9)
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 5/17
8 9
Input / Output Signal
Direction of Signal
(CPU ← Module)
Direction of Signal
(CPU → Module)
Input Name of Signal Output Name of Signal
X00 Module ready Y10
X01 Y11
X02Flag indicating the
operation condition set upY12
Requesting to set up
operation condition
X03
Refer to “HELP” menu
in CICON
Y13
Refer to “HELP” menu
in CICON
X04 Y14
X05 Y15
X06 Y16
X07 Y17
X08 Y18
X09 Y19
X0A Y1A
X0B Y1B
X0C Y1C
X0D Y1D
X0E Y1E
X0FFlag indicating error in
moduleY1F Requesting to clear error
SP04EAO USER MEMORY
AddressDescription Default R/W
Hexa Deci
0H 0 CH.1 Digital converted value - R
1H 1 CH.2 Digital converted value - R
2H 2 CH.3 Digital converted value - R
3H 3 CH.4 Digital converted value - R
4H 4 CH.1 Input signal value - R
5H 5 CH.2 Input signal value - R
6H 6 CH.3 Input signal value - R
7H 7 CH.4 Input signal value - R
8H 8 CH.1 Percentage value - R
9H 9 CH.2 Percentage value - R
AH 10 CH.3 Percentage value - R
BH 11 CH.4 Percentage value - R
CH 12 CH.1 Input range setting 0 R/W
DH 13 CH.2 Input range setting 0 R/W
EH 14 CH.3 Input range setting 0 R/W
FH 15 CH.4 Input range setting 0 R/W
10H 16 Raw Value Digital Output set 0 R/W
11H 17 Reserved - -
12H 18 CH.1 Average processing setting value 2000h R/W
13H 19 CH.2 Average processing setting value 2000h R/W
14H 20 CH.3 Average processing setting value 2000h R/W
15H 21 CH.4 Average processing setting value 2000h R/W
16H 22 CH.1 Max. alarm set value 0 R/W
17H 23 CH.2 Max. alarm set value 0 R/W
18H 24 CH.3 Max. alarm set value 0 R/W
19H 25 CH.4 Max. alarm set value 0 R/W
1AH 26 CH.1 Min. alarm set value 0 R/W1BH 27 CH.2 Min. alarm set value 0 R/W
1CH 28 CH.3 Min. alarm set value 0 R/W
1DH 29 CH.4 Min. alarm set value 0 R/W
1EH 30 Alarm in Max status - R
1FH 31 Alarm in Min. status - R
20H 32 CH.1 Digital Filter Constant 30 R/W
21H 33 CH.2 Digital Filter Constant 30 R/W
22H 34 CH.3 Digital Filter Constant 30 R/W
23H 35 CH.4 Digital Filter Constant 30 R/W
24H 36 Calibration Code - R/W
25H 37 Error Code - R
26H 38 OS Version - R
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 6/17
10 11
SP04EAA USER MEMORY
Hexa
0H
1H
2H
3H
4H
5H
6H
7H
8H
9H
AH
BH
CH
DH
EH
FH
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
1AH1BH
1CH
1DH
1EH
Deci
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
2627
28
29
30
-
-
-
-
-
-
-
-
0
0
0
2000h
2000h
0
0
0
0
30
30
0
0
0
0
0
0
0
00
0
-
-
R
R
R
R
R
R
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/WR/W
R/W
R
R
CH.1 Digital converted value (AD)
CH.2 Digital converted value (AD)
CH.1 Input signal value (AD)
CH.2 Input signal value (AD)
CH.1 Percentage value (AD)
CH.2 Percentage value (AD)
Alarm in Max status (AD)
Alarm in M in. status (AD)
CH.1 Input range setting (AD)
CH.2 Input range setting (AD)
Raw Value Digital output set (AD)
CH.1 Average processing setting value(AD)
CH.2 Average processing setting value (AD)
CH.1 Max. alarm set value (AD)
CH.2 Max. alarm set value (AD)
CH.1 Min. alarm set value (AD)
CH.2 Min. alarm set value (AD)
CH.1 Digital Filter Constant (AD)
CH.2 Digital Filter Constant (AD)
Enable / Disable to D/A convert setup
CH.1 DA Output type (current 2, voltage 4)
CH.2 DA Output type (current 2, voltage 4)
CH.1 DA range of Digital value
CH.2 DA range of Digital value
CH.1 DA Channel Hold / Clear
CH.2 DA Channel Hold / Clear
CH.1 Digital Output value (DA)CH.2 Digital Output value (DA)
AD / DA Resolu tion Set
Error Code
OS Version
AddressDescription R/WDefault
SP04EOAV / SP04EOAI USER MEMORY
Hexa
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
10H
11H
12H
13H
14H
15H
16H
17H
Deci
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R
R
R
R
R/W
Enable/Disable to D/A convert setup
CH.1 Digital Output value
CH.2 Digital Output value
CH.3 Digital Output value
CH.4 Digital Output value
CH.1 Range of Digital value
CH.2 Range of Digital value
CH.3 Range of Digital value
CH.4 Range of Digital value
CH.1 Channel Hold / Clear
CH.2 Channel Hold / Clear
CH.3 Channel Hold / Clear
CH.4 Channel Hold / Clear
CH.1 Range of Voltage output setup
CH.2 Range of Voltage output setup
CH.3 Range of Voltage output setup
CH.4 Range of Voltage output setup
CH.1 Status
CH.2 Status
CH.3 Status
CH.4 Status
Error Code
OS Version
DA Output Enable
(Same Function to I/O Y Signal)
AddressDescription R/WDefault
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 7/17
12 13
Features of SP04EAM
Analog Mux module receives analog values from 4 channels and outputs the samevalues to one port at a time.
Desired channels can be selected to be enabled or disabled and get operationstatus.
Different relay ON time can be set by each channel from 0.1 to 1000.0 secondsrange.
Relay count values can be checked for life expectancy for the relay.
Easy control with Auto/Manual mode.
Power LED blinks by 0.5 second interval when there’s an error with CPU
communication.
It is not suitable for current signal use since this module switches analog signalsrepeatedly.
1)
2)
3)
4)
5)
6)
Input / Output Signal of SP04EAM
** Note that I/O ags shown above are applied when the MUX module is installed in the rst slot
Flag Direction (CPU ← MUX Module) Flag Direction (CPU → MUX Module)
Input Flag Output Flag
X20 MUX Channel Change Completed Y20
X21 Settings Save Completed Y21 Mux Channel Change Request
X22 1CH Relay Open Predict Y22 Settings Save Request
X23 2CH Relay Open Predict Y23 1CH stoppage Request
X24 3CH Relay Open Predict Y24 2CH stoppage Request
X25 4CH Relay Open Predict Y25 3CH stoppage Request
X26 1CH Relay Activate Y26 4CH stoppage Request
X27 2CH Relay Activate Y27
X28 3CH Relay Activate Y28
X29 4CH Relay Activate Y29
X2A 1CH Relay Count Reset Completed Y2A
X2B 2CH Relay Count Reset Completed Y2B 1CH Relay Count Reset Request
X2C 3CH Relay Count Reset Completed Y2C 2CH Relay Count Reset Request
X2D 4CH Relay Count Reset Completed Y2D 3CH Relay Count Reset Request
X2E Module Error Y2E 4CH Relay Count Reset Request
X2F MUX Channel Change Completed Y2F Error Clear Request
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 8/17
14 15
SP04EAM USER MEMORY
AddressContents R/W
Hex. Dec.
0H 0 MUX Channel Enable / Disable R/W
1H 1 CH.1 Relay Count High R
2H 2 CH.1 Relay Count Low R
3H 3 CH.2 Relay Count High R
4H 4 CH.2 Relay Count Low R
5H 5 CH.3 Relay Count High R
6H 6 CH.3 Relay Count Low R
7H 7 CH.4 Relay Count High R
8H 8 CH.4 Relay Count Low R
9H 9 Auto/Manual Mode R/W
AH 10 Operation Status R
BH 11 CH.1 ON time setting value R/W
CH 12 CH.2 ON time setting value R/W
DH 13 CH.3 ON time setting value R/W
EH 14 CH.4 ON time setting value R/W
FH 15 Error Code R
10H 16
11H 17
12H 18
13H 19
14H 20 OS Version R
Wiring Method
► CM3-SP04EAO
► CM3-SP04EAA
Voltage Input
Voltage Input / Output
Current Input
Current Input / Output
CH 1
CH 2
CH 3
CH 4
AD Ch 1
AD Ch 2
DA Ch 1
DA Ch 2
CH 1
CH 2
CH 3
CH 4
AD Ch 1
AD Ch 2
DA Ch 1
DA Ch 2
Terminal 1
Terminal 4
Terminal 7
Terminal 10
Terminal 1
Terminal 4
Terminal 7
Terminal 10
Terminal 1
Terminal 4
Terminal 7
Terminal 10
Terminal 1
Terminal 4
Terminal 8
Terminal 11
Terminal 3
Terminal 6
Terminal 9
Terminal 12
Terminal 3
Terminal 6
Terminal 9
Terminal 12
Connect 1-2
Connect 4-5
Connect 7-8
Connect 10-11
Connect 1-2
Connect 4-5
Terminal 3
Terminal 6
Terminal 9
Terminal 12
Terminal 3
Terminal 6
Terminal 9
Terminal 12
Channel
Channel
Channel
Channel
+ Terminal
+ Terminal
+ Terminal
+ Terminal
- Terminal
- Terminal
Connection
Connection
- Terminal
- Terminal
24V Extenrnal
24V Extenrnal
24V Extenrnal
24V Extenrnal
Connection : bottom of module
Connection : bottom of module
Connection : bottom of module
Connection : bottom of module
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 9/17
16 17
Wiring Method
► CM3-SP04EOAV, CM3-SP04EOAI
► Prior to wiring Analog Input to Terminal, double check terminal (+) and (–)
CH 1
CH 2
CH 3
CH 4
Terminal 1
Terminal 3
Terminal 5
Terminal 7
Terminal 2
Terminal 4
Terminal 6
Terminal 8
Channel + Terminal - Terminal
24V Extenrnal Connection : bottom of module
► CM3-SP04EAM
CH 1
CH 2
CH 3
CH 4
Terminal 1
Terminal 4
Terminal 7
Terminal 10
Terminal 3
Terminal 6
Terminal 9
Terminal 12
Channel + Terminal - Terminal
Input Wiring
► SP04EAO Voltage Input ► SP04EAO Current Input
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 10/17
18 19
Input Wiring
► SP04EAA Voltage Input ► SP04EAA Current Input
Output Wiring
► SP04EOAI Voltage Output ► SP04EOAI Current Output
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 11/17
20 21
Output Wiring
► SP04EAA Voltage Output ► SP04EAA Current Output
SP04EAM Wiring
A1+
A1-
COM1
A2+
A2-
COM2 A1+
A1-
COM
CH1
CH2
CH3
CH4
A3+
A3-
COM3
A4+
A4-
COM4
► MUXING
► Bottom Terminal
► Analog Output
► Analog Input
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 12/17
22 23
SP04EAM Wiring Example Dimension
Unit : mm
► All analog modules are the same size.
TC sensor
► Analog Output ► Analog Input
A1+
A1-
COM
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 13/17
24 25
Dimension Revision History
Version Date Content Page
V1.0 2014-02-25 New Revision
V1.1 2015-01-26 SP04EAM added
V1.2 2015-05-27 SP04EAM Wiring / SP04EAM Wiring Example
V1.3 2015-10-27 Wiring Method
-
1 - 28
21 - 22
15
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 14/17
26 27
Product Warranty
January 2014
All Cimon products including hardware, software, and rmware (collectively called
“Products”) carry a one-year warranty against defects in materials and workmanship
beginning from the date of product receipt from seller or its appointed distributor. If a
product proves defective in materials and workmanship within one year from the date
of purchase, we will replace or repair it. Products returned under warranty after
30 days may be replaced with refurbished or remanufactured goods at Cimon’s
discretion. Cimon makes no representation or warranty, express or implied,
that the operation of the Products will be uninterrupted or error free, or that the
functions contained therein will meet or satisfy buyer’s intended use or requirements.Repaired or replaced Products provided as a result of this warranty are
warranted for a period of six (6) months from the shipment to buyer or the
remainder of the original warranty term for that particular product, whichever
is longer. Cimon’s standard policy is that all customers are responsible for freight
charges to Cimon when returning products under the warranty return policy.
This warranty will be void if Products date codes or serial numbers are removed or
defaced. Warranties do not apply to products that have been subjected to abnormal
use, abnormal conditions, improper storage, exposure to moisture or dampness,
unauthorized modications, unauthorized repair, misuse, neglect, accident, alteration,
improper installation or other acts which are not the fault of Cimon, including damage
caused in shipping. Our warranty also does not apply to any product that has
been damaged by external causes such as re, ood, sand, dirt, lightning, acts of
God, battery leakage, theft, blown fuses, improper use of any electrical source or
connection to product not recommended in writing for interconnection by Cimon.
In no event will Cimon be liable, whether in contract, tort or under any other legal
theory, for lost profits or revenues, loss of use or similar economic loss, for any
indirect, special, incidental, consequential, punitive or similar damages arising out
of or in connection with any products including non-conforming products, or for any
third party claims against you relating to the products, even if we have been advised of
the possibility of such claim. In no event will our monetary liability in respect of any
product exceed the purchase price that you paid for it.
Product Warranty
To minimize the risk of potential safety problems, you should follow all applicable
local and national codes that regulate the installation and operation of your
equipment. These codes vary from area to are and usually change with time. It is your
responsibility to determine which codes should be followed, and to verify that the
equipment, installation and operation is in compliance with the latest revision of these
codes.
CIMON SOFTWARE AND HARDWARE (COLLECTIVELY REFFERED TO AS,
“PRODUCTS”) LICENSE DISCLAIMER AND LIMITATION OF WARRANTIES
YOUR USE OF ANY CIMON PRODUCTS AND CONTENT ACCESSIBLE THROUGH
THE PRODUCTS IS ENTIRELY AT YOUR OWN RISK. EXCEPT AS DESCRIBED IN THIS
AGREEMENT, THE PRODUCTS ARE PROVIDED "AS IS." TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, CIMON, ITS AFFILIATES, AND ITS THIRD PARTY
SERVICE OR DATA PROVIDERS, LICENSORS, DISTRIBUTORS OR SUPPLIERS
(COLLECTIVELY REFERRED TO AS, "SUPPLIERS") DISCLAIM ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY THAT THE PRODUCTS ARE
FIT FOR A PARTICULAR PURPOSE, TITLE, MERCHANTABILITY, DATA LOSS, NON-
INTERFERENCE WITH OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY
RIGHTS, OR THE ACCURACY, RELIABILITY, QUALITY OR CONTENT IN OR LINKED TO
THE PRODUCTS.
CIMON AND ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT THE
PRODUCTS ARE SECURE, FREE FROM BUGS, VIRUSES, INTERRUPTION, ERRORS,
THEFT OR DESTRUCTION. FURTHER, CIMON DOES NOT WARRANT ACCESS TO
THE INTERNET OR TO ANY OTHER SERVICE, CONTENT OR DATA TRANSMITTED
THROUGH THE PRODUCTS. IF THE EXCLUSIONS FOR IMPLIED WARRANTIES DO
NOT APPLY TO YOU, ANY IMPLIED WARRANTIES ARE LIMITED TO 60 DAYS FROM
THE DATE OF PURCHASE OR DELIVERY OF THE PRODUCTS, WHICHEVER IS
SOONER.
EQUIPMENT DAMAGE OR SERIOUS INJURY TO PERSONNEL INCLUDING DEATH
CAN RESULT FROM THE FAILURE TO FOLLOW ALL APPLICABLE CODES AND
STANDARDS INCLUDING ENGINEERING STANDARDS. CIMON DOES NOT
ASSUME ANY RESPONSIBILITY FOR YOUR PRODUCT DESIGN, INSTALLATION OR
OPERATION.
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 15/17
28 29
Product Warranty
CIMON LTD AND ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY REP-
RESENTATIONS OR WARRANTIES THAT YOUR USE OF THE PRODUCTS WILL
SATISFY OR ENSURE COMPLIANCE WITH ANY LEGAL OBLIGATIONS OR LAWS OR
REGULATIONS.
LIMITATION OF LIABILITY AND INDEMNITY. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, THE ENTIRE LIABILITY OF CIMON, AND ITS AFFILIATES
AND SUPPLIERS FOR ALL MATTERS OR CLAIMS RELATING TO THIS AGREEMENT
SHALL BE LIMITED TO THE AMOUNT YOU PAID FOR THE PRODUCTS DURING THE
TWELVE (12) MONTHS PRIOR TO SUCH CLAIM.
THE STATUTE OF LIMITATIONS FOR FILING A CLAIM SHALL BE LIMITED TO THE
SHORTER OF TWELVE MONTHS, OR THE SHORTEST PERIOD ALLOWED UNDER
APPLICABLE LAW.
SUBJECT TO APPLICABLE LAW, CIMON AND ITS AFFILIATES AND SUPPLIERS ARE
NOT LIABLE FOR ANY OF THE FOLLOWING: (A) INDIRECT, SPECIAL, INCIDENTAL,
PUNITIVE OR CONSEQUENTIAL DAMAGES; (B) DAMAGES RELATING TO FAILURES
OF TELECOMMUNICATIONS, THE INTERNET, ELECTRONIC COMMUNICATIONS,
CORRUPTION, SECURITY, LOSS OR THEFT OF DATA, VIRUSES, SPYWARE, LOSS
OF BUSINESS, REVENUE, PROFITS OR INVESTMENT, OR USE OF SOFTWARE
OR HARDWARE THAT DOES NOT MEET CIMON SYSTEM REQUIREMENTS. THE
ABOVE LIMITATIONS APPLY EVEN IF CIMON AND ITS AFFILIATES AND SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND/OR THE
POSSIBILITY OF DAMAGES GREATER THAN THE LIMITATION ABOVE. THIS
AGREEMENT SETS FORTH THE ENTIRE LIABILITY OF CIMON, ITS AFFILIATES ANDYOUR EXCLUSIVE REMEDY WITH RESPECT TO THE SOFTWARE AND ITS USE.
THE PARTIES FURTHER AGREE THAT THE APPLICABLE LAW AND VENUE FOR
ANY DISPUTED ARE THE LAWS OF CALIFORNIA. TO THE EXTENT ALLOWED BY
APPLICABLE LAW, ANY CLAIMS SHALL BE BROUGHT IN LOS ANGELES CALIFORNIA
AND CALIFORNIA LAW SHALL APPLY. THE CALIFORNIA VERSION OF THE UCC IS
THE PREFERRED LAW TO BE APPLIED TO ANY WARRANT AND RELATED CLAIMS.
MEMO
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 16/17
30 31
MEMO MEMO
8/16/2019 SP04EAO Modulo Analogo CIMON
http://slidepdf.com/reader/full/sp04eao-modulo-analogo-cimon 17/17
Version:1.3
Revision Date : Oct, 2015
Printed : May, 2015
BCP18044
H.Q Address : 5F KDT B/D, #48, Beolmal-ro, Bundang-gu,Seongnam-si, GyeongGi-do, Korea
463-836
Tel : +82-31-778-3071
Homepage : www.cimon.com
USA : 3699 Wilshire Blvd suite 1250 Los Angeles CA90010
Tel : 213 384-8703
Homepage : www.cimon.com
CIMON CO.,LTD.