Sony Cfd-s35cp Ver-1.1 Sm

7/25/2019 Sony Cfd-s35cp Ver-1.1 Sm

http://slidepdf.com/reader/full/sony-cfd-s35cp-ver-11-sm 1/64

SERVICE MANUAL

Sony CorporationPersonal Audio Group

Published by Sony Engineering Corporation

AEP Model UK Model

E Model

CD RADIO CASSETTE-CORDER

9-879-598-022005E04-1 © 2005.05

Ver. 1.1 2005.05

SPECIFICATIONS

CFD-S35CP

CD player section

SystemCompact disc digital audio system

Laser diode properties

Material: GaAlAs

Wave length: 780 nm

Emission duration: Continuous

Laser output: Less than 44.6 µW

(This output is the value measured at a distance

of about 200 mm from the objective lens surface

on the optical pick-up block with 7 mm

aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm)

(CLV)

Number of channels

2Frequency response

20 - 20,000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

E Model

FM 87.5 - 108 MHz

AM MX model:

530 - 1,710 kHz

other models:

531 - 1,611 kHz (9 kHz step)

530 - 1,610 kHz (10 kHz step)

AEP, UK Model

FM 87.5 - 108 MHz

MW 531 - 1,611 kHz (9 kHz step)

530 - 1,610 kHz (10 kHz step)

LW 153 - 279 kHz

AerialsFM: Telescopic aerials

AM/MW/LW: Built-in ferrite bar aerials

Cassette-corder sectionRecording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette C-60

Frequency response

TYPE I (normal): 80 - 10,000 Hz– Continued on next page –

CD

Model Name Using Similar Mechanism CFD-S350/S350L

Section CD Mechanism Type KSM-213CDP

Optical Pick-up Name KSS-213C

TC Model Name Using Similar Mechanism CFD-S350/S350L

Section Tape Transport Mechanism Type MF-S350



CFD-S35CP

• Abbreviation

EA : Saudi Arabia model

KR : Korean model

MX : Mexican model

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN

THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS

WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS

MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

CAUTIONUse of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 °C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Notes on chip component replacement• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostatic

breakdown because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic breakdown and also use

the procedure in the printed matter which is included in the repair

parts.

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-

up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

GeneralSpeaker

Full range: 10 cm dia., 3.2Ω, cone type (2)

Outputs

Headphones jack (stereo minijack):

For 16 - 68 Ω impedance headphones

Maximum Power output

MX model: 2.3 W + 2.3 W

(at 3.2 ohms, 10% harmonic distortion)

other models: 5.2 W

Power requirements

For CD radio cassette-corder:

MX model: 120 V AC, 60 Hz

KR model: 220 V AC, 60 Hz

EA model: 220-240 V AC, 50/60 Hz

Other models: 230 V AC, 50 Hz

9 V DC, 6 R20 (size D) batteries

For remote control:

3 V DC, 2 R03 (size AAA) batteries

Power consumption

AC 14 W

Battery life

For CD radio cassette-corder:

FM recordingSony R20P: approx. 13.5 h

Sony alkaline LR20: approx. 20 h

Tape playback

Sony R20P: approx. 7.5 h


CD playback

Sony R20P: approx. 2.5 h


Dimensions

Approx. 420 × 155 × 260 mm (w/h/d)

(incl. projecting parts)

Mass

Approx. 3.7 kg (incl. batteries)

Supplied accessory

Mains lead (1)

Remote control (1)

Conversion plug adaptor (1) (UK model)

Design and specifications are subject to change

without notice.

Ver. 1.1



CFD-S35CP

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 4

2. GENERAL ................................................................... 5

3. DISASSEMBLY3-1. Cabinet Top Assy ............................................................. 7

3-2. Cabinet Front Assy, Cabinet Rear Assy ........................... 7

3-3. Wires................................................................................ 8

3-4. MD Block ........................................................................ 8

3-5. Holder Cassette................................................................ 9

3-6. POWER KEY Board ....................................................... 9

3-7. MAIN Board.................................................................... 10

3-8. TUNER Board, POWER Board ...................................... 10

3-9. CD Lid ............................................................................. 11

3-10. LCD Block Assy .............................................................. 11

3-11. CD Block Assy ................................................................ 12

3-12. Optical Pick-up ................................................................ 12

3-13. R/P Head (HRP301), Erase Head (HE301), TC Board ... 13

3-14. Motor Assy (M801), RF Belt .......................................... 13

4. MECHANICAL ADJUSTMENTS ......................... 14

5. ELECTRICAL ADJUSTMENTSTape Section .................................................................... 14

Tuner Section................................................................... 15

CD Section ...................................................................... 17

6. DIAGRAMS6-1. Block Diagram – CD Section – ...................................... 19

6-2. Block Diagram – TUNER-2 BAND Section – ............... 20

6-3. Block Diagram – TUNER-3 BAND Section – ............... 21

6-4. Block Diagram – MAIN Section –................................. 22

6-5. Printed Wiring Board – MP3-CD Section – ................... 24

6-6. Schematic Diagram – MP3-CD Section – ...................... 25

6-7. Printed Wiring Board – TUNER-2 BAND Section – ..... 26

6-8. Schematic Diagram – TUNER-2 BAND Section –........ 27

6-9. Printed Wiring Board – TUNER-3 BAND Section – ..... 28

6-10. Schematic Diagram – TUNER-3 BAND Section – ........ 29

6-11. Printed Wiring Boards – MAIN Section – ..................... 30

6-12. Schematic Diagram – MAIN Section (1/2) – ................. 31

6-13. Schematic Diagram – MAIN Section (2/2) – ................. 32

6-14. Printed Wiring Board – TC Section – ............................. 33

6-15. Schematic Diagram – TC Section – ............................... 34

6-16. Printed Wiring Boards – CONTROL Section – ............. 35

6-17. Schematic Diagram – CONTROL Section – .................. 36

6-18. Printed Wiring Boards – POWER Section – .................. 376-19. Schematic Diagram – POWER Section – ...................... 38

7. EXPLODED VIEWS7-1. Cabinet Section................................................................ 46

7-2. Cabinet (Front) Section ................................................... 47

7-3. Cabinet (Top) (1) Section ................................................ 48

7-4. Cabinet (Top) (2) Section ................................................ 49

7-5. Cabinet (Rear) Section .................................................... 50

7-6. Tape Mechanism Section (MF-S350) .............................. 51

7-7. CD Mechanism Section (KSM-213CDP) ....................... 52

8. ELECTRICAL PARTS LIST .................................. 53

•UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.



CFD-S35CP

LASER DIODE AND FOCUS SEARCH OPERATIONCHECK

1. Turn ON the [POWER] or [OPERATE] button and press [CD]

button to CD position.

2. Open the CD lid.

3. Turn on S801 with screwdriver, etc. as following figure.

4. Press the N X (CD) button.

5. Confirm the laser diode emission while observing the objecting

lens. When there is no emission, Auto Power Control circuit

or Optical Pick-up is broken.

Objective lens moves up and down three times for focus search.

CHUCK PLATE JIG ON REPAIRING

On repairing CD section, playing a disc without the lid (CD), use

Chuck Plate Jig.

• Code number of Chuck Plate Jig: X-4918-255-1

S801

SECTION 1

SERVICING NOTES



CFD-S35CP

SECTION 2GENERAL This section is extracted

from instruction manual.

4

Playing an audio CD or MP3 files

Connect the supplied mains lead (see page 23).

1 Press CD.

(On the remote, press OPERATE

(POWER, see page 2) and then press

FUNCTION repeatedly until "CD"

appears in the display.)

2 PressZ PUSH OPEN/CLOSE downto open the CD compartment and

place the CD on the CDcompartment.

3 Close the lid of the CD compartment.

With the label side up

1 4 2, 3

Basic Operations

B

a si c O p er a t i on s

5

Display

Playingtime

Tracknumber

To Press

adjust the volume VOLUME +*, –

(VOL +*, – on the remote.)

stop playback x

pause playback u* (X on the remote)

Press the button again to

resume play after pause.

go to the next track >

go back to the previous track .

remove the CD Z PUSH OPEN/CLOSE**

turn on/off the player OPE RATE

(or POWER, see page 2)

* The button has a tactile dot.

**Once you open the CD compartment, the track to start play will

change to the beginning of the first track.

TipPlayback starts from the

track you last stopped

playing (Resume play).

During stop, the track

number to be played are

displayed.

To cancel the resume play

to start play from the

beginning of the first track,

press x in stop mode.

u

OPERATE(POWER)

VOLUME +, –

x

Z PUSHOPEN/CLOSE

continued

4 Pressu (N on the remote).

The player plays all the tracks once.

To play a CD with MP3 files, see

page 6.

.,>

Use these buttons for additional operations

6

Note

Before playing a file, this

player reads all file and

folder information on the

CD. Depending on the file

structure, it may take more

than a minute to read them.

During this time,

“READING” is displayed.

Tip

You can use the buttons

mentioned in the table on

page 5 for additional

operations in the same way

as when playing an audio

CD.

Playing a CD with MP3 files

1 Press CD.

2 PressZ PUSH OPEN/CLOSE to open the CD

compartment and place the CD on the CD

compartment (see page 4) .

3 Close the lid of the CD compartment.

4 Pressu.

The player plays all MP3 files on the CD.

When you play a CD with MP3 files, MP3 indicatorlights up.

To select a folderPress FLDR + to go forward and FLDR – to go backward .

Press FOLDER +, – on the remote.

To select a file

Press> to go forward and. to go backward.

Track number

u

.,>

CD

After the file name isdisplayed, the playing timewill appear

Z PUSHOPEN/CLOSE

Playing an audio CD or MP3 files (continued)

FLDR +, –

MP3 indicator

B a si c O p er a t i on s

7

Example of folder structure and playingorder

The playing order of the folders and files is as follows:

Notes

• A folder that does not

include an MP3 file is

skipped.

• Maximum number of

folders: 255

Maximum number of files:

255

• Folder names and file

names can be displayed

with up to 64 characters.

• The characters A - Z, a - z,

0 - 9, and _ can be

displayed on this player.

Other characters are

displayed as “*”.

• This player conforms to

Version 1.1 of the ID3 tag

format. If the file has the

ID3 tag information, “song

title”, “artist name” and

“album name” can be

displayed.

About CD-Rs/CD-RWs and MP3 files

This player can play CD-Rs/CD-RWs recorded in the CD-

DA format* and MP3 files recorded in the CD-ROMformat, but playback capability may vary depending on the

quality of the disc and the condition of the recording

device.

* CD-DA is the abbreviation for Compact Disc Digital Audio. It is

a recording standard used for Audio CDs.

CD-R

CD-RW

3

2

1

2

4

5

3

6

7

8

4

95

06

1

Folder

MP3 file



CFD-S35CP

SECTION 3

DISASSEMBLY

3-1. CABINET TOP ASSY (Page 7)

3-2. CABINET FRONT ASSY,CABINET REAR ASSY (Page 7)

3-11. CD BLOCK ASSY (Page 12)

SET

3-3. WIRES (Page 8)

3-4. MD BLOCK (Page 8)

3-7. MAIN BOARD (Page 10)

3-5. HOLDER CASSETTE (Page 9)

3-9. CD LID (Page 11)

3-6. POWER KEY BOARD (Page 9)

3-10.LCD BLOCK ASSY (Page 11)

3-8. TUNER BOARD,POWER BOARD (Page 10)

3-13. R/P HEAD (HRP301),ERASE HEAD (HE301),TC BOARD (Page 13)

3-14. MOTOR ASSY (M801),RF BELT (Page 13)

3-12.OPTICAL PICK-UP (Page 12)

• This set can be disassembled in the order shown below.



CFD-S35CP

3-1. CABINET TOP ASSY

3-2. CABINET FRONT ASSY, CABINET REAR ASSY

Note: Follow the disassembly procedure in the numerical order given.

0 CNP804 (20 core)qa CNP802 (15 core)

3 CD lid

5 handle

qs cabinet top assy

cassette holder

2 two screws (+P (B2.6 ) )

6 three screws (+BV (B2.6 ) )

4 two screws (+BV (B2.6 ) )


8

1

9 connector (S801)

7 battery lid

1 screw (+PWH (B2.6 ) )

2 HEADPHONE board

3 CNP323 (4P)

6 CNP801 (3P)

5 CNP302 (4P)

4 CNP805 (13 core)

qs cabinet front assy

qd cabinet rear assy

0 three screws(+BV (B2.6 ) )



qa

Ver. 1.1



CFD-S35CP

3-3. WIRES

3-4. MD BLOCK

A

F G

H

C

E

from HEADPHONE board

cabinet front

cabinet bottom

B D



3 MD block



CFD-S35CP

3-5. HOLDER CASSETTE

3-6. POWER KEY BOARD

3 holder cassette

two claws

two claws

4 cassette spring

2 damper 1 screw (+BV (B2.6 ) )

4 POWER KEY board

5 power button

2

1 three screws

3 three screws

Ver. 1.1



CFD-S35CP

3-7. MAIN BOARD

3-8. TUNER BOARD, POWER BOARD


1 CNP803 (11 core)

2 CNP321 (4P)

6 MAIN board

3 CNP322 (4P)

4 HEADPHONE board

9 screw (+BV (B2.6 ) )


8 two screws (+BV (B2.6 ) ) 0 POWER board

4 two claws 6 TUNER board

5

1 screw (+P (M3 ) )

3 screw (+BV (B2.6 ) )

2 telescopic antenna

Ver. 1.1



CFD-S35CP

3-9. CD LID

3-10. LCD BLOCK ASSY

3 CD lid

1 two claws

2 two claws

CD spring

5 two screws

0 CNP407 (5P)

2 CD KEY HOLD (2) board

4 CD KEY HOLD (1) board

6 screw

7 screw

qd three screws

qf button (folder) sub assy

qa screw

8 two screws

qs mode button

qg LCD block assy

9

1 screw (+P (B2.6 ) )

3 screw (+P (B2.6 ) )



CFD-S35CP

3-11. CD BLOCK ASSY

3-12. OPTICAL PICK-UP

4 CD block assy

3 CD cover

two claws

two claws

1 two screws (+PWH (B2.6 ) )2 two screws

(+PWH (B2.6 ) )

claw

1 gear (A)

2 claw 3

4 sled shaft

5 optical pick-up



CFD-S35CP

3-13. R/P HEAD (HRP301), ERASE HEAD (HE301), TC BOARD

3-14. MOTOR ASSY (M801), RF BELT

4 lug

5

two claws

1 R/P head (HRP301)2 erase head (HE301)

3 screw (+BVTT 2 × 4)

6Remove the four solderings.

7 TC board

3 screw

6 screw

7 motor assy (M801)8 motor bracket

5 RF belt

4

1 screw (+P (B2.6 ) )

claw

2 protect chassis



CFD-S35CP

SECTION 4

MECHANICAL ADJUSTMENTS

PRECAUTION1. Clean the following parts with a denatured alcohol-moistened

swab:

record/playback heads pinch rollers

erase head rubber belts

capstan idlers

2. Demagnetize the record/playback head with a head

demagnetizer. (Do not bring the head magnetizer close to the

erase head.)

3. Do not use a magnetized screwdriver for the adjustments.

4. The adjustments should be performed with the rated power

supply voltage (9V) unless otherwise noted.

Torque Measurement

Mode Torque meter Meter reading

2.95 – 6.86 mN • m

FWD CQ-102C (30 – 70 g • cm)

(0.42 – 0.97 oz • inch)

0.15 – 0.53 mN • m

FWD CQ-102C (1.5 – 5.5 g • cm)back tension

(0.021 – 0.076 oz • inch)

more than 5.88 mN • m

FF CQ-201B (more than 60 g • cm)

(more than 0.83 oz • inch)

more than 5.88 mN • m

REW CQ-201B (more than 60 g • cm)

(more than 0.83 oz • inch)

Tape Tension Measurement

Mode Torque meter Meter reading

more than100 gFWD CQ-403A(more than 3.53 oz)

SECTION 5

ELECTRICAL ADJUSTMENTS

TAPE SECTION 0 dB=0.775V

• Standard Output Level

Output terminal HP OUT

load impedance 32 Ω

output signal level 0.25 V (–10 dB)

• Test Tape

Type Signal Used for

WS-48A 3 kHz, 0 dB tape speed adjustment

Tape Speed AdjustmentProcedure:

Mode: playback

Adjust so that the value on the digital frequency counter is

3,000 Hz.

Specification Value:

Digital frequency counter

2,910 to 3,090 Hz

Adjust so that the frequency at the beginning and that at the end of tape winding are between 2,910 to 3,090 Hz.

Adjustment Location:

i jack (J321)

set

32 Ω

test tape WS-48A(3 kHz, 0 dB)

digital frequencycounter

Tape speed adjustment control inside motor



CFD-S35CP

AM/MW IF ADJUSTMENT

Adjust for a maximum reading on level meter

T1 450 kHz

AM FREQUENCY COVERAGE ADJUSTMENT

(EA, KR, MX, SP, TH model)

Adjustment Part Frequency Display Reading on Digital Voltmeter

L4 531 kHz 1.0 ± 0.05 V

Confirmation 1,611 kHz 4.8 ± 0.7 V

AM TRACKING ADJUSTMENT (EA, KR, MX, SP, TH model)


L3 621 kHz

CT3 1,404 kHz

MW FREQUENCY COVERAGE CONFIRMATION

(CET, RU model)

Frequency Display Reading on Digital Voltmeter

531 kHz 0.9 ± 0.4 V

1,611 kHz 5.2 ± 0.5 V

MW TRACKING ADJUSTMENT (CET, RU model)


L3-1 621 kHz

CT3 1,404 kHz

LW FREQUENCY COVERAGE ADJUSTMENT (CET, RU model)


Confirmation 153 kHz 0.6 ± 0.05 V

L4 279 kHz 5.3 ± 0.5 V

LW TRACKING ADJUSTMENT (CET, RU model)


L3-2 162 kHz

CT5 261 kHz

FM IF ADJUSTMENT

Adjust for a minimum reading on level meter

T2 10.7 MHz

FM FREQUENCY COVERAGE ADJUSTMENT


L2 108 MHz 3.0 ± 0.2 V

Confirmation 87.5 MHz 1.3 ± 0.3 V

FM TRACKING ADJUSTMENT


L1 87.5 MHz

CT1 108 MHz

Adjustment and Connecting Location:

TUNER board (See page 16)

• Abbreviation CET : East European and CSI model.

EA : Saudi Arabia model.

KR : Korean model.

MX : Mexican model.

RU : Russian model.

SP : Singapore model.

TH : Thai model.

TUNER SECTION 0 dB=1 µV

[AM/MW]

Setting:

Function: RADIO

Band: AM or MW or LW

[FM]Setting:

Function: RADIO

BAND button: FM

• Repeat the procedures in each adjustment several times, and

the tracking adjustments should be finally done by the trimmer

capacitors.

• Remove FM antenna in FM adjustment.

AM/MW RF signalgenerator

30% amplitude modulation by 400 Hz signal Output level:as low as possible

Put the loop antenna close tothe set.

+ –

level meter

set

32 Ω

i jack (J321)

FM RF signal generator

75 kHz frequency deviation by 1 kHz signal Output level:

as low as possible

+ –

level meter

set

32 Ω0.01 µF

TUNER board TP (GND)

TUNER board TP-ANT(JW2)

i jack (J321)

digital voltmeter

TP (CV)TP (GND)

100 k Ω

TUNER board



CFD-S35CP

Adjustment and Connecting Location:

L3 AM TRACKING ADJUSTMENT L3-2 LW TRACKING ADJUSTMENT

L3-1MW TRACKING ADJUSTMENT CT1

FM FREQUENCY COVERAGE ADJUSTMENT

L2 FM FREQUENCY COVERAGE ADJUSTMENT

L4 AM/MW FREQUENCY COVERAGE ADJUSTMENT

CT5

LW TRACKING ADJUSTMENT

CT3 AM/MW TRACKINGADJUSTMENT

TP-ANT (JW2)

IC1

– TUNER BOARD (Component Side) –

TP (GND)

TP (CV)

TP-ANT JW2

– TUNER BOARD (Conductor Side) –

L1FM TRACKNG ADJUSTMENT

T1AM IF ADJUSTMENT

T2 FM IF ADJUSTMENT



CFD-S35CP

Q701

R 7 0 1

R702

R703

R704

R705

R 7 0 6

R707

R 7 0 8

R709R711

R

R 7 1 9

R 7 2 2

R729R 7 3 0

R 7 4 5

C 7 0 1

C 7 0 3

C 7 0 5

C706 C 7 4 0

C 7 1 0

C 7 1 1

C 7 1 2

C 7 1 3

C714

C 7 1 6

C 7 1 7

C 7 1 8

C719

C 7 2 0

C 7 4 5

C750

C 7 5 1

C 7 2 1

R710

R 7 3 1

R 7 5 5

R756

R 7 5 7

R758

R759

R 7 2 4

R 7 2 5

R726

R727R728

C708C746

C 7 4 2

C743

C 7 4 4

R 7 6 3

R764

IC7

C N P 7 0 1

M701

C704

C 7 2 3

C707

C 7 1 5

C709

TP (RF)

TP (VC)

CD SECTION

CD section adjustments are done automatically in this set.

In case of operation check, confirm that focus bias.

FOCUS BIAS CHECK

1. Connect the oscilloscope between IC701 pin 4 and pin qa(or TP (RF) and TP (VREF)).

2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)

3. Press the N X (CD) button.

4. Confirm that the oscilloscope waveform is as shown in the

figure below. (eye pattern)

A good eye pattern means that the diamond shape ( ) in the

center of the waveform can be clearly distinguished.

• RF signal reference waveform (eye pattern)

Test Point:

– MP3-CD Board (Side B) –

RF level : 0.85 ± 0.2 Vp-p

VOLT/DIV : 50 mV (10 : 1 probe in use)TIME/DIV : 500 nS

When observing the eye pattern, set the oscilloscope for AC range

and raise vertical sensitivity.



CFD-S35CP

MEMO



24 24

FD-S35CP

CFD-S35CP

. PRINTED WIRING BOARD – MP3-CD SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

I C 7 0 2

R744

R743

R 7 1 2 C

7 4 7

R704

R 7 5 7

C 7 2 3 R

7 5 5

C 7 4 4

R726

C746 R728

R764

R729

C709

R707 R709

R711

R710

R759 C 7 0 5

Q701 R 7 3 0

C706

R

7 0 8

C 7 1 0

C 7 1 1

C 7 1 2C704

C714

C719

C707

C 7 1 6

C 7 0 1

C 7 4 0

C 7 1 3

C

7 1 5

C 7 1 7

C 7 1 8

C 7 2 0

C 7 2 1

R727

C708

R702

C750

R 7 0 6

C 7 0 3

R 7 4 5

R 7 2 5

R 7 6 3

C N P 7 0 1

M702

CNP702

C1001

R760

R753 C753

C1057

C1029

R703

R705

R756

R758

R1075

R107 6

R1077

R1078

C1056

R1001

R1002

R1079

R1080

C10 31

C1044

C1010

R717

C743 IC1001

C 7 4 8

C 7 0 2

R 7 1 6

C 7 5 4

R 7 1 8

C 7 4 1

R 7 3 1 R

7 2 0

R 7 2 1

C 7 4 5

R 1 0 6 8

R 1 0 7 3

R 1 0 7 4

C 1 0 5 8

C 1 0 5 9

C 1 0 4 3

C 1 0 4 2

C762

R 7 2 4

C 7 4 2

F B 7 0 2

F B 7 0 5

F B 7 0 6

F B 7 0 7

S 7 0 1

M701

R 7 0 1

R 7 2 2

C 7 5 1

R 7 3 2

R 7 3 3

R 7 3 4

R 7 3 5

R 7 3 6

R 1 0 0 3

R 1 0 0 4

R 1 0 0 5

C 7 6 1

C 7 6 3

C 7 6 4

C 7 6 6

C 1 0 6 6

C 1 0 6 7

C 1 0 6 8

C 1 0 6 9

C 1 0 7 0

R 7 2 3

R737

C 7 6 0

C 7 6 7

R765

F B 1 0 0 1

F B 1 0 0 2

FB703

FB704

R 7 1 9

R1018

R1019

R1020C1011

C 1 0 7 4

R1082

IC701

R740

C 7 2 2

C756

C1012C1013

C1037

FB701

R766

R 7 1 3

R1017

R1081

X 7 0 1 R

7 1 4

R 7 1 5

C 7 3 2

C 7 3 3

R 7 6 1

R 7 6 2

C 7 3 7

C 1 0 1 4

C 7 2 9

C 7 3 0

C1055

C 7 3 4

C 7 3 1

C 1 0 3 0

I C 1 0 0 3

C 1 1 1 0

IC1002

C 1 0 5

4

(Page 30)CNP804

• Semiconductor

Location

Ref. No. Location

IC701 E-10IC702 C-8IC1001 D-12IC1002 C-13IC1003 B -12

Q701 F-8



25 25

CFD-S35CP

CFD-S35CP

6-6. SCHEMATIC DIAGRAM – MP3-CD SECTION –

IC B/D

IC B/D

(Page 32)

C717

C706

C707

C714

C721

C 7 2 2

R707

R731

C1042

C702

C723

R724

C747

C740

C709

C701

R712

R 7 2 5

R 7 2 6

R745

R753

R760

R762

C746

R715

R714

R744

R 1 0 1 9

R1018R1082

R1068

R759

C1110

R743

C748

C715

C710

IC702

C 7 4 4

C 7 4 3

C1011

C1012

C1043

C1031

C1055

IC1002

R713

R1001

C1014

R1081R1017

FB701

C742

R728 R727

R729R730C708

C1044

R1080

C713R711R708R710R709

C705

C719 C720

C716

IC701

IC1001

Q701C704

S701

M702

M701

R1020

CNP701

C703

C718

C754

C753

C741

C745

C751

C767

R765

R761

C756

C7 3 4 C7 31

IC1003

C1074

C1010

C1054

CNP702

X701

FB703

FB1001

FB1002FB704

C750

R766

C1059

R740

C712

C711

S L 7 0 1

S L 7 0 2

S L 7 0 3

S L 7 0 4

FB702

FB705

FB706

FB707

R706

R701

R702

R703

R704

R705

R755

R756

R757

R758

C1030

C1029

C 1 0 3 7

C 1 0 1 3

R1002

R1003

R1004

R1005

C 1 0 6 9

C 1 0 7 0

C 1 0 6 8

C 1 0 6 7

C 1 0 6 6

C766

R735

R736

R737

C764

C760

C761

C762

C763

R 7 2 3

R 7 3 2

R 7 3 3

R 7 3 4

R 7 1 6

R 7 1 7

R 7 1 8

R 7 1 9

R 7 2 0

R 7 2 1

R 7 2 2

R 7 6 3

R 7 6 4

C737

C729

C733

C730

C732

R 1 0 7 8

R 1 0 7 6

R 1 0 7 5

R 1 0 7 4

C1058

C1057

C1001

C1056

R 1 0 7 3

R 1 0 7 7

R 1 0 7 9

C

• See page 40, 41 for IC Block Diagrams. • See page 39 for Waveforms.



26 26

FD-S35CP

CFD-S35CP

. PRINTED WIRING BOARD – TUNER-2 BAND SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

BMAIN

BOARDCNP803

1-863-438- 11

MXMODEL

MXMODEL

EA,KR,SP,TH MODEL

EA,KR,SP,TH MODEL

R61

R60

R58

R59 C 6 3 I C

2

R 5 6

R 5 0

C 6 2

C 6 1

R94

C60C68

C66 R4

R91

C57

R52 C 5 2

C 5 1

C 2 6

C 2 7

R63

R10

R65

C37

R 1 1

C39

D 1 1

D 1 0

R1

C8

ANT1

FM TELESCOPIC

ANTENNA

R3

C34

C35

D 1 C4

C 3 2

R 3 2

R2

C 1

C78

C15

C 1 1

C9

C14

C80

C13

R24

R 3 1

C 3 3

R41

C 7 7

R 9 2

C 2 0

C 2 4

C 2 2

C56

C 3 0

D2

C 3 1

R 3 0

R 4 0

C 4 1

C 4 7

C 4 2

C 4 3

R 5 1

R13

C 5 5

R 5 4

C 9 5

R53

C59

R57

R 3 3

R 5

R14

R 5 5

JC33

JC34

JC2

JC4

J C 3

J C 2 4

J C 6

J C 5

J C 1 3

JC12

J C 1 1

C7

JC1

J W 1 3

C29 C 6 5

L21

C53

X1

JW3

J W 5

C 5 4

J W 7

C21

J W 9

J W 2

C10

T 1

J W 1 2

CF4

CF2

J W 1 1

T 2

L 1

L 1 1

C 1 8

C T 1

JW8

I C 1

C12

L 2

C23

J W 1 0

L 4

D 3

L3

L3

AM FERRITE BAR ANTENNA

CT3

C49

J W 4

J W 6

C N P 1

JW14

TP(GND)

TP(CV)

(Page 30)

• Semiconductor

Location

Ref. No. Location

D1 C-10D2 D-8D3 D-8D10 B-12D11 B-12

IC1 E-10IC2 F-4



27 27

CFD-S35CP

CFD-S35CP

6-8. SCHEMATIC DIAGRAM – TUNER-2 BAND SECTION –

IC B/D

IC B/D

(Page 32)

C10

C12

C18

C21

C29

C54

CF4

JC1JC2

JC3

JC4

JC5

JC6

JC33

JC34

L4

R2

R3

R4

R10

R24

R32

R41

R51

R58

R59R60R61

CF2

R92

R30

R14

R11

JC24

CT3

CT1

X1

C32

C35 C33

C34

C31

C30

C1

C8

C4

C11

C9

C24

C80

C37

C39

C20C22

C7

C77

C78

C51 C52

C95

C61 C62 C63

C57

C56

L 1

D 1

L 2

D 2

R 3 1

R 3 3

R53

R50C55

R91

C41

C42

IC1

R1

D 1 1

D 1 0

C68

C66

C60R94 R13

R56

R57

L21CNP1

ANT1

R54

IC2

T2

C 49 R 40

C43

D3

C23

R5

C53

R55

R52

C59

R63

L3

JC12 JC11C47

JC13 T1

C65

R65

C27C26

C15C14

L11

C 1 3

• See page 41, 42 for IC Block Diagrams. • See page 39 for Waveform.



28 28

FD-S35CP

CFD-S35CP

. PRINTED WIRING BOARD – TUNER-3 BAND SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

BMAIN

BOARDCNP803

1-863-438- 11

R61

R60

R58

R59 C 6 3 I C

2

R 5 6

R 5 0

C6

R18

R9

C5

C 5 8

R66

C 6 2

C 6 1

R64

R94

C60C68

C66

R93

R4

R91

C57

R52 C 5 2

C 5 1

R63

R10

R16

C 2

R 4 2

R 1 7 R

1 9

Q 1 4

R 2 2

Q41

C 3

C37

C72

C71

C 7 0

Q 1 2

R12

C93

R 1 1

C25

C 4 4

C 4 0

C39

D 1 1

D 1 0

R1

C8

ANT1

FM TELESCOPIC

ANTENNA

R3

C34

C35

D 1 C4

C 3 2

R

3 2

R2

C 1

C78

C15

C 1 1

C9

C14

C80

R24

R 3 1

C 3 3

R41

C 7 7

R 9 2

C 2 0

C 2 4

C 2 2

C56

C 3 0

D2

Q 4 2

C 3 1

C46R43

R 3 0

Q 4 3

C48C45

R 4 0

Q 4 4

C73

R7

C 4 1

C 4 2

C 4 3

R 5 1

R13

C 5 5

R 5 4

C 6 4

C 9 5

R53

C59

R57

R 3 3

R14

R 5 5

JC33

JC34

JC2

JC4

J C 3

J C 2 2

J C 2 4

J C 6

JC23

J C 5

C7

JC1

J W 1 3

C29

L21

C53

X1

JW3

J W 5

C 5 4

J W 7

C21

J W 9

J W 2

C10

T 1

J W 1 2

CF4

CF2

J W 1 1

T 2

L 1

C 1 8

C T 1

JW8

I C 1

C12

L 2

C23

J W 1 0

L 4

D 3

L3-2

L3-1

L3

MW/LW FERRITE BAR ANTENNA

CT3

C49

C T 5

J W 4

J W 6

Q61

C N P 1

JW14

TP

(GND)

TP(CV)

(Page 30)

• SemiconductorLocation

Ref. No. Location

D1 C-10D2 D-8D3 D-8D10 B-12D11 B-12

IC1 E-10IC2 F-4

Q12 F-7Q14 B-4Q41 B-5Q42 C-9Q43 C-6Q44 D-6Q61 D-3



29 29

CFD-S35CP

CFD-S35CP

6-10. SCHEMATIC DIAGRAM – TUNER-3 BAND SECTION –

IC B/D

IC B/D

(Page 32)

C10

C12

C18

C21

C29

C53 C54

CF4

D3

JC1JC2

JC3

JC4

JC5

JC6

JC22

JC33

JC34

L4

R2

R3

R4

R7

R9

R10

R12

R16

R19

R24

R32

R40

R41

R42

R43

R51

R52

R58

R59R60R61

R93

CF2

R92

R30

R14

R11

JC23

JC24

CT5

CT3

CT1

X1

C73C48

C3

C46

C45

C32

C35C33

C34

C31

C30

C1

C8

C4

C14

C11

C9

C24

C80

C2 C37

C6C5

C72

C 71 C 44 C7 0 C40

C39

C93

C20C22

C7

C15

C77

C78

C 51 C52

C95

C61 C62 C63C64

C57

C56

C58

L 1

D 1

L 2

D 2

R 3 1

R 3 3

R17

R22

C59

R55

R53

R50C55

R91

R18

C49

C41

C42

C43

IC1

R1

D 1 1

D 1 0

R66

C68

C66

C60R94 R13

R56

R57

R63

L21 CNP1

ANT1

C 2 5

R54

Q12

Q14

Q44

Q43

Q41

Q42

IC2

T1

T2

L3

C23

R64

Q61

• See page 41, 42 for IC Block Diagrams. • See page 39 for Waveform.



30 30

FD-S35CP

CFD-S35CP

1. PRINTED WIRING BOARDS – MAIN SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13

S801

PUSHOPEN/CLOSE

GRY

RED

J321

i

SP302SPEAKER

(R-CH)

SP301SPEAKER

(L-CH)

RED

BLK

BLK

RED

1-865-641-

11

(11)

11

(11)1-865-645-

A

SW1

M801(CAPSTAN/REEL)

CNP302

(LEAF SW)

MP3-CDBOARDCNP702

FPOWERBOARDCNP321

C

B TUNER

BOARDCNP1

TCBOARDCN301

4 1

D

LCD BOARD

E

POWER KEYBOARD

R246

R146

FB101

FB201

C N P 3 2 3

C N P 3 2 2

IC302

C952

D953

C951

R 9 5 4 R

9 5 5

R 9 6 0

C 1 3 9

C 2 3 9R132R232

C 1 4 6

C135

R 1 3 3

C246 C 2 3 5

R233

R 3 3 4

R 3 3 5

C329

C122

C222

C 3 3 2

C 3 3 3

C 3 3 4

C 3 3 5

R 2 3 5

R236

R 2 3 4

R 1 3 4

R 1 3 5

R136

C 1 2 9

C229

R 1 4 0

R 2 4 0

R229

R241 C 2 0 8

C 1 0 8

R141

R129

C110R143

C210R243

Q124

Q 2 2 4

R 1 4 5

R 2 4 5 D

3 2 3

C 3 2 4

R 3 2 4

R 3 3 2

C350

C352

Q 2 2 2

Q 1 2 2

R 1 3 7

R138

R139

R239

C206

C106

R323

R961R962

R963R964

Q 9 5 1

D951

D958

Q 9 5 3

R956

R957

R952R953R951

Q 8 0 8

R846

R 9 0 0

C907

I C 8 0 1

IC803

IC802

R801R802R803

R804

R 8 0 6

R 8 0 7

R 8 0 8

C804

J C 3 0 4

J C 3 0 6

J C 3 0 3

J C 3 0 5

R 8 8 2

R 8 0 9

R 8 1 0

R 8 1 1

R 8 8 3

R890

J C 3 1 0

J C 3 0 9

R 8 1 4

C839

C 8 4 0

C841

C842

C843

Q811

Q802

R 8 1 9

R 8 1 8

C 8 3 5

C 8 3 4

R 8 2 0

C836

R 8 2 1

R 8 2 2

C 8 3 7

C 8 3 8

Q 8 1 0

R 8 9 8

R 8 9 9

R 8 4 1

R891

R 8 1 5 R

8 6 8

R

8 1 6

R823

R82 6

C 8 2 0

R 8 2 5

C862

C 8 2 1 C

8 6 0C861

R 8 2 4

C863

C 8 5 8

C 8 5 9

C853

C 8 5 6

R834R833 C864

C832

R870

C822

R 8 2 7

R 8 2 8

R 8 6 9

C831

R832C857

C810

C811

R 8 3 0

R831

R 8 6 0

R 8 5 9

R 8 5 8

R 8 5 7

R 8 5 3

R 8 5 2

C803

C812

R 8 4 3

Q 8 0 4

R 8 4 2

R896

R 8 9 2

C 8 4 7

R 8 9 3

C 8 4 6

R 8 9 5

Q807

R865

R 8 9 4

Q803

R879

R333

C957

C960

R 3 2 5

R 3 2 6

D 3 2 4

C 1 4 8

C 2 4 8

Q809Q806

R887

R866

R 8 3 5

R 8 8 4

R885 R886D803

R 8 3 6

R 8 3 8

R 8 3 7

Q 8 1 4

R829

D809

D804

D 8 0 1

R851

R877 C830R876

C829R875

R874 C828

C827

R880

R 8 7 3

R 8 7 2

R 8 7 1

C826

C 8 2 5

C 8 2 4

C850

C851

C852

R848

R849

F B 8 5 5

F B 8 5 6

Q812

R 8 8 9

R

8 1 3

R

8 1 2

R 8 5 5 R

8 4 4

R 8 4 0

R 8 5 0

D957 R 9 5 9

R958

C819

C818

C813

C814

C815

R 8 1 7

Q 8 0 1

D322

R 2 3 7

R238

R 8 8 1

R 1 0 1

R 2 0 1

C227

C 1 2 7 R805

C 8 7 1

F B 8 5 4

F B 8 4 5

F B 8 6 1

F B 8 6 2

JC814

R 3 3 1

R847

C351

C353

C354

Q815

C

3 2 0

D 8 0 5

R 8 7 8

I C 3 0 4

K H 3 0 1

C953

C107

C321

C 3 2 7

C328

C 2 1 5

C 1 1 5

C211 C212

C

1 1 1 C112

C 2 0 9

C 1 0 9

C 3 2 2

C331

C325

Q955

C N P 8 0 5

C225

C125

C323

Q952

X801

L803

L804

C845

C 8 5 5

Q 9 5 7

C959

C326

C823

C882

CNP802

C N P 8 0 3

K H 8 0 1

CNP804

CNP321

CNP302

CNP801

C 8 0 1

J W 8 4 4

JW801

JW803

JW805

C881

C247

C147

JW802

J W 8 0 6JW807

JW808

JW809

JW810

JW812

JW813

JW816

J W 8 1 7

JW818

JW820

JW821

J W 8 2 2

J W 8 2 4

J W 8 2 5

JW826

JW827

JW831

J W 8 3 2

JW833

JW834

JW836

JW837

J W 8 3 8

JW839

J W 8 4 0

JW841

J W 8 4 2

JW843

JW846

J W 8 4 7

J W 8 4 8 J

W 8 4 9

J W 8 5 0

JW851

J W 8 5 2

JW854

JW855

EA,MX,SP,TH

AEP,UK,CET,MX

AEP,UK,CET,KR,RU

CET,KR,MX

EA,KR,RU,SP,TH

EA,RU,SP,TH

JW856

JW859

JW860

J W 8 6 4

J W 8 6 5

JW866

JW867

J W 8 4 5

C207

JW804

JW835JW830

JW863

JW811

JW853

JW814

JW862

JW815

JW823

JW858JW861

J W 8 5 7

C330

JW829

JW819

JW828

Q813

IC80 4

(Page 33) (Page 35) (Page 35)

(2 BAND: Page 26)

(3 BAND: Page 28)

(Page 24)(Page 37)

• SemiconductorLocation

Ref. No. Location

D322 E -4D323 G-5D 32 4 D -1 1D801 B -7D803 B -8D804 B -6D805 G-9D809 B -7D951 E -5D953 H-2D957 H-8D958 E -5

I C3 02 B -4I C3 04 G -3I C8 01 E -9

I C8 02 C -9I C8 03 D -6I C8 04 D -7

Q122 E -3Q124 F-4Q222 E -4Q224 F-4Q801 B -8Q 80 2 H -1 1Q803 F-6Q804 F-7Q806 G-8Q807 F-7Q808 D-5Q809 G-9Q810 C-8Q 81 1 G -1 1Q812 D-7Q813 D-7Q814 B -7Q815 F-7Q951 E -5Q952 D-5Q953 E -5Q955 H-2Q957 H-9

r. 1.1



3131

CFD-S35CP

CFD-S35CP

6-12. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) –

IC B/D

(Page 32)

(Page 38)

SOUND/

R952

R951

R239

Q 1 2 4

Q 2 2 4

Q951

R956

R957

CNP323

R146

R246

TP301

Q952

D324

C 1 1 1

C115

C215

R953

D323

D 9 5 7

R 1 2 9

CNP322KH301

R 3 3 4

R 3 3 5

SW1

D 9 5 8

CNP321

CN305 CNP302

C951

C229

C206

C106

C129

C320

J321

C247

C147

R143

C110 C210

R243

R140

R240

IC304

D322R238

R237

C227

C225

C127

C125

R138

R139

R137

R236R235

R234

R136R135

R134

C324R324R323C323

R245

R145

C321 C329

R884 R885

R886D803C823C325

D951C953C952

R959 R958

C957C959R333

C960

C326

R325

R326

D953

R846

R 90 0 C 90 7

C211

C 2 1 2

C 1 1 2

IC302

Q955

Q957

D801

C 35 2 C 35 0

Q808M801

Q953

C331

Q122

Q222

C 3 2 7

C 3 3 5

C 3 3 4

C 3 3 3

C 3 3 2

C 1 0 7

C 2 0 7

C 1 2 2

C 2 2 2

C 3 2 8

C 1 3 9

C 2 3 9

C 1 4 6

C 1 3 5

C 2 4 6

C 2 3 5

R 2 3 2

R 1 3 2

R 2 3 3

R 1 3 3

C 3 5 1

C 3 5 3

R 3 3 2

R 3 3 1

R 9 6 3

R 9 6 4

R 9 6 1

R 9 6 2

R 9 5 4

R 9 5 5

R 9 6 0

FB201

FB101

SP301

SP302

C 2 0 9

C 1 0 9

C 3 2 2

R 2 4 1

R 2 2 9

R 1 4 1

C 2 0 8

C 1 0 8

• See page 42 for IC Block Diagram.

Ver. 1.1



32 32

FD-S35CP

CFD-S35CP

3. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) –

IC B/D

(Page 34)

(Page 31)

(2 BAND:Page 27)

(3 BAND:Page 29)

(Page 36)

(Page 36)

(Page 25)

L803

L804

R 8 7 0

R 8 2 3

R 8 2 7

R 8 2 8

R 8 6 9

R 8 4 7

R 8 4 8

R 8 4 9

R818

R836

R838

R891

S801

C881

C882

D809

R834

R879

R832

R829

R880

Q806

X 8 0 1

KH801

R844

R850

R855

R817

CNP802

R201

R840

R851

R 8 2 6

CNP801

CNP804

CNP803

Q802

Q811

C 8 0 4

C863

C857

C803 C812

JC814

R837

R894

R895R893

C846

R892

C847

R896

C801

R 83 5 R 88 7 R 86 5

R866Q809

Q815

C856C855C845C853

C818C819

R889

C248

C148

R831R830

C810

C811

C 8 2 2

R819

R833

C864

C832

C831

R824

R825

C862

C820 C821

R877D805

R878

R871

R881

C330

C354

R899R898

CNP805

IC802

IC803

IC801

Q812

C858

C859

C860 C861

Q813

Q803

Q814D804

Q810

Q801

Q804

Q807

R101

IC804 C 8 4 3

C 8 4 2

C 8 4 1

C 8 4 0

C 8 3 9

R882

R883

R890

JC304

JC306

JC309

JC303

JC305

JC310

C828

C829

C830

R806

R807

R808

R802

R803

R804

R805

R801

R810

R811

R809

R816

R815

R814

R868

R812

R813

R 8 2 0

R 8 2 1

R 8 2 2

C 8 1 3

C 8 1 4

C 8 1 5

C 8 5 0

C 8 5 1

C 8 5 2

R843

R842

R841

C 8 3 4

C 8 3 5

C 8 3 6

C 8 3 7

C 8 3 8

C 8 7 1

R860

R859

R858

R857

FB862

FB861

FB845

FB856

FB855

FB854

R853

R852

C824

C825

C826

C827

R 8 7 6

R 8 7 3

R 8 7 5

R 8 7 4

R 8 7 2

• See page 43 for IC Block Diagrams. • See page 39 for Waveform. • See page 44 for IC Pin Function Description.

r. 1.1



33 33

CFD-S35CP

CFD-S35CP

6-14. PRINTED WIRING BOARD – TC SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1

A

B

C

D

E

F

G

2 3 4 5 6 7

C

C 1 0 3

R 2 1 0

R206

R 2 0 1

R301

BLK

R 1 0 4

R 1 0 3

R202

R 2 0 3

R 2 0 4

C 1 0 4

C 2 0 3

C 2 0 4

C 2 0 1

C 1 0 5

R 3 0 5

R 3 1 1

R 1 0 1

C 1 0 1

C308

JC304

R 3 1 0

C310

R 1 0 2

C 1 0 7

C 2 0 7

R307

C307

R306

C305

R308

C306

R303 J C 3 0 1

R 2 1 1

R 2 0 5

J C 3 0 3

R309

R304

JC302

R 1 1 1

R105

R 1 0 6

R302

R 1 1 0

JC305JC306

JC307JC308

Q 3 0 1

Q 3 0 2

Q 3 0 3 J

C 3 0 9

R 1 1 2

R 2 1 2

R 3 1 4

R 3 1 5

IC301

CN303

T301

C102

C302

C 2 0 2

C301

C304

C 3 0 3

S301

-1-2S301

(REC/PB)REC

PB

R-CH

HRP301RECORD/PLAYBACK

HEAD

L-CH

Y E L

R E D

W H T

B L K

(CHASSIS)

HE301ERASEHEAD

1-688-389- (11)

11

C 2 0 5

C 3 0 9

AEP,UK,CET,RUMODEL

MAIN

BOARDCNP805

(Page 30)

Ver. 1.1



34 34

FD-S35CP

CFD-S35CP

5. SCHEMATIC DIAGRAM – TC SECTION –

IC B/D

AEP,UK,CET,RU MODEL

R301

C301

R101

C302C309

C205R201R210

R106

R206

R302

R303

R 3 0 4

R309

C303

C304

R306

R111

R211

R203R202

R103

R102

R308

C105

C103

C203

C207

T301

C102

R104

R112

R212

R204

C202

C201

C204

IC301

JC302

JC306

JC308

JC305

JC307

JC301

J C 3 0 3

JC304R314 R315

C310 C308

R311R310

Q301

R307

R305

Q303Q302

JC309

R105

R205

CN303

C307

C306

C305

R110

HRP301

S301

C107

C104

C101

(Page 32)

• See page 43 for IC Block Diagram. • See page 39 for Waveforms.

r. 1.1



35 35

CFD-S35CP

CFD-S35CP

6-16. PRINTED WIRING BOARDS – CONTROL SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

D

1-865-644- 11

(11)

11

(11)

11

(11)1-865-643-

RED

GRY

BLK

R423R414 R 4 1 5

R417

R418R431

R432

R 4 3 3

R422

R407R408

R413R424 R 4 2 6

R428

R 4 2 9

R430

R406

R440

R443

C 4 0 1

S 4 0 5

S 4 0 7

S408

S413S414

S415S416

S417S418

S409

S410 S411

S412

JW409

I C 4 0 1

R 4 2 0

R 4 4 2

C406

R411

R412

R421

R427

C407 C 4 0 8

R438R439

C 4 0 9

C 4 1 0

C413

C 4 0 3

C 4 0 5

R404

R405

R 4 0 9

R 4 1 0

R 4 4 4

R 4 4 5

R450

JC401

R452

R403

R 4 5 1

R453

R416

S 4 0 3

S404

S421

D408

D407

S422

S423CNP401 J W 4 0 6

J W 4 0 2

J W 4 0 3

JW405

JW404

JW408

JW407

L 4 0 1

L402 JW401

1 33

MAIN BOARDCNP802

PRESET /

FLDR

FLDR

MP3

/ PRESET

TUNE / / TUNE

LCD401

LIQUID CRYSTAL DISPLAY PANELD405

OPR/BATT

MODE

REPEAT

DISP/ENT/ MEMORY

TAPE

BAND/ RADIO

AUTO RESET

S411

MEGA BASS

SOUND

CD

S402

SLEEP

S401

OPERATE

1-865-642-

VOLUME

VOLUME

D407(BACK LIGHT)

MAINBOARD

CNP801

E

(Page 30)

(Page 30)

3 1

IC402



36 36

FD-S35CP

CFD-S35CP

7. SCHEMATIC DIAGRAM – CONTROL SECTION –

(Page 32)

(Page 32)

OPERATE

R439

R438

R427

R412

R411

R 4 20 R 4 42

R406

R426

R428

R429

R430

R440

R401R402

R403 R404 R444 R445

IC401

S405S407

S412

S409

S410

S411

IC402

R443

S401S402

R 40 5 R 40 9 R 41 0

CNP401

D407D408

L402R452

C403

C 40 5 R 41 6

L401

JC401

C413

R451R453

D405

R450

C401

R424

R413

LCD401

S408

S418

S417

S413

S414

S415

S416

R423

R414

R407

R408

R422

R415

R417

R418

R432

R431

R433S422 S423S421S404S403

C410

C409

R421

C406

C407

C408



37 37

CFD-S35CP

CFD-S35CP

6-18. PRINTED WIRING BOARDS – POWER SECTION – • See page 23 for Circuit Boards Location. :Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

R E D

G R Y

G R Y

GRY

R E D

G R Y

G R Y

T901

J901

MAIN BOARDCNP321

1-725-705- (11)

11

(11)

11

(11)

11

1-865-646-1-865-647-

F

KH901

C N P 9 0 4

C901

C903

C902

C904

JW905

CNP901

D901

D902

D903

D904

F 9 0 2

J901

C906

KH902

(Page 30)



38 38

FD-S35CP

CFD-S35CP

9. SCHEMATIC DIAGRAM – POWER SECTION –

(Page 31)

D903

D904

D901

D902

J901

CNP901CNP904KH901

KH902

C901

C902

C903

C904

T901

F902

FH901

FH902

TP901

TP902

TP904

TP905

C906



CFD-S35CP

• Waveforms

1.4 Vp-p

5.0 MHz

1 IC801 ek (X2)

1 V/DIV, 50 nsec/DIV

1

IC701

4 (RF)

0.85 ± 0.2Vp-p

1.8V

4 Vp-p

16.9 MHz

Approx. 100 mAVp-p

500 mV/DIV, 0.5 µsec/DIV

4

IC701 rk (XOUT)

2 V/DIV, 0.05 µsec/DIV

2 IC701

qd (FE)

100 mV/DIV, 200 µsec/DIV

5 IC701 t; (FSX/16MIN(I))

2 V/DIV, 0.05 µsec/DIV

1.8V

Approx. 100 mAVp-p

3 IC701 qg (TE)

100 mV/DIV, 200 µsec/DIV

6 IC1001 7 (CKIN(I))

2 V/DIV, 50 µsec/DIV

6 Vp-p

59 nsec

6 Vp-p

59 nsec

– MP3-CD Board –

4 Vp-p

40 Vp-p

1

Q301C REC

0.1 V/DIV, 5 µsec/DIV

2 T301,HRP301(YEL)

10 V/DIV, 5 µsec/DIV

19.5 µsec

19.5 µsec

– TC Board –

1.0 Vp-p

75 kHz

1 IC2 w; (XOUT)

0.5 V/DIV, 5 µsec/DIV

– TUNER Board –

– MAIN Board –



CFD-S35CP

– MAIN Board –

IC302 BD3870FS-E2

IC2 LC72137M-TLM-E

11

10

9

8

7

6

5

4

3

2

1

12

13

14

15

16

19

20

UNLOCKDETECTOR

POWER ONRESET

UNIVERSALCOUNTER

CCBI/F

CE

DI

CL

DO XOUT

LP-OUT

XIN

LP-IN

PD

VSS

VDD

MO/ST

FM IN

AM IN

MUTE

MW/LW

BAND

ST-IND

BAND

IF IN

PHASEDETECTORCHARGEPUMP

REFERENCEDIVIDER

SWALLOWCOUNTER1/16,1/17

4BITS

12BITSPROGRAMMABLE

DIVIDER

D A T A

S H I F T

R E G I S T E R

L A T C H

1/2

17

18

V I N 1

V I N 2

S E L 2

S E L 1

A 1

A 2

B 1

B 2

C 1

C 2

F I L T E R

G N D

C A P

T N F 1

T N F 2

B N F 2

B O U T 2

B N F 1

B O U T 1

O U T 1

O U T 2

S I

S C

V C C

BASS1

f0=80Hz

BASS2

f0=80Hz

21 20 19 18 17 16 15 14 13

TREBLE2

f0=8kHz

22

TREBLE1

f0=8kHz

23

S U R R O U N D

24

1 2 3 4

LOGIC

VCC/2

VCC/2

VCC/2 VCC/2 VCC/2

5 6 7 8 9 10 11 12



CFD-S35CP

IC802 CAT24WC02WI-1.8-TE13

– TC Board –

IC301 TA2068N

A0

A1

A2

GND

VCC

WP

SCL

SDA

1K BIT EEPROM ARRAY

ADDRESSDECODER

HIGH VOLTAGEOCCURENCE CIRCUIT

POWER SUPPLYVOLTAGE DETECTION

DATAREGISTER

SLAVE • WORDADDRESSREGISTER

CONTROL CIRCUIT

7

6

5

8

1

2

3

4

7BIT 8BIT

7BIT

START STOP

ACK

1

2

3

6

9

10

11

12

8

7

4

5

22

T A P E

TAPE

T A P E

BUF AMP

A1

BUF AMP

A2

NAB

AMP1

NAB

AMP2

23

24

15

14

13

21

20

17

16

RADIO

BUF AMP

B1

BUF AMP

B2

MUTE

M U T E

ON

ON

O N

7dB

26dB

26dB

MONITOR

AMP

LOGIC

18

19

MUTE

7dB

MONITOR

AMP

LINE

TAPERADIO

LINE

A L C 2

A L C 1

D E T

REC

AMP1

REC

AMP2

2.1

REF

AMP

MICAMP1

VCC

R.LO

LINE

R.RAD

TAPE

R.LIN

MIC

L.LO

REC

L.RAD

MIC I/EX

L.LINAGC

L.PO

L.NF

L.RO

L.IN

REF

GND

R.IN

R.RO

R.NF

R.PO

MIC.NF



CFD-S35CP

• IC Pin Function DescriptionMAIN BOARD IC801 uPD784216AGF (SYSTEM CONTROL)

Pin No. Pin Name I/O Description

1 TU-CE O Tuner PLL chip enable signal output

2 TU-DATA O Tuner PLL data signal output3 TU-CLK O Tuner PLL clock signal output

4 TU-COUNT I Tuner PLL data signal input

5 TU-MUTE O IF mute signal output

6 SIMUKE1 I Destination port input


8 TEST B I Not used. (Pull down)

9 VDD — Power supply

10 TEST A I Not used. (Pull down)

11 EPROM-SCL O EEPROM serial clock output

12 EPROM-SDA I/O EEPROM serial data input/output


14 to 16 NC — Not used. (Open)

17, 18 ISS1, ISS2 O Tuner beat change signal output

19 TU-ON O Tuner power supply control signal output

20 TAPE-ON O Tape power supply control signal output

21 CD-ON O CD power supply control signal output

22 TEST/VPP I Not used. (Pull down))

23, 24 NC — Not used. (Open)

25 SLEEP-LED O LCD back light control signal output


28 MP3-LED O MP3 LED control signal output

29 LCD-RST O LCD driver reset signal output

30 LCD- C/D O LCD driver command data output

31 LCD CS O LCD driver chip select signal output

32 LCD DATA O LCD driver serial data output

33 LCD CLK O LCD driver serial clock signal output

34 NC — Not used. (Open)

35 FM/AM SHIFT O Tuner band control signal output


37 VDD — Power supply

38 X2 O Oscillation signal output (5 MHz)39 X1 I Oscillation signal input (5 MHz)

40 VSS — Ground

41 XT2 O Not used. (Open)

42 XT1 I Not used. (connected ground)

43 RESET I System reset signal input

44 AC-CHK I AC power supply check signal input

45 RMC IN I Remote control signal input

46 WAKE-UP I Key interrupt signal input

47 INITLI I Mode read signal input

48 CD-DOOR I CD door detection signal input

49 INTB(MP3) I Interrupt signal input from MP3 decoder

50 WRQ(CD) I CD write request data input

51 AVDD — Power supply

52 AVREF0 I A/D reference voltage input



CFD-S35CP

Pin No. Pin Name I/O Description

53 to 55 KEY1 to KEY3 I Function key signal input

56 MODE O Mode read signal output


58 REG-CHK I Regulator +6V voltage check input

59 VH I Battery voltage check signal input

60 VM I Battery center voltage check signal input

61 AVSS — Ground


64 AVREF1 I A/D reference voltage input


68 CMDOUT(MP3) O MP3 serial data output to MP3 decoder

69 CMDIN(MP3) I MP3 serial data input from MP3 decoder

70 CL(MP3) O MP3 serial clock output to MP3 decoder

71 NC — Not used. (Open)72 DRF(CD) I CD DRF signal input

73 DO(CD) I CD serial data input

74 DI(CD) O CD serial data output

75 CL(CD) O CD serial clock output

76 CE(CD) O CD chip enable signal output

77 FSEQ(CD) I CD frame synchronizing signal detection input

78 RES(CD) O CD reset signal output

79 (MP3)RESB O MP3 reset signal output

80 (MP3)CE O MP3 chip enable signal output


91 A-MUTE O Line mute signal output

92 MEGABASS O MEGABASS control signal output

93 P-CON O Power supply control signal output

94 V-DATA O E-volume control data output

95 V-CLOCK O E-volume control data clock output


97 TAPE PLAY I Tape play detection signal input

98 REC-IN I Tape recording detect signal input


100 VSS — Ground



CFD-S35CP

SECTION 7

EXPLODED VIEWS

NOTE:• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

• Items marked “*” are not stocked since they

are seldom required for routine service.

Some delay should be anticipated when

ordering these items.

• The mechanical parts with no reference

number in the exploded views are not supplied.

• Abbreviation

CET : East European and CSI model.


KR : Korean model.

MX : Mexican model.

RU : Russian model.


TH : Thai model.

• Accessories are given in the last of electrical

parts list.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

7-1. CABINET SECTION

1 3-261-973-01 LID, BATTERY (SILVER)...(SILVER)

1 3-261-973-41 LID, BATTERY (BLUE)...(BLUE)

2 3-254-140-01 SCREW (B2.6), (+) BV TAPPING (for BLUE)

2 3-254-140-11 SCREW (B2.6), (+) BV TAPPING (for SILVER)

3 2-547-157-11 COVER (HANDLE) (R) (BLUE)...(BLUE)

3 2-547-157-21 COVER (HANDLE) (R) (SILVER)...(SILVER)

4 2-547-159-11 HOLDER (HANDLE) (R) (BLUE)...(BLUE)

4 2-547-159-21 HOLDER (HANDLE) (R) (SILVER)...(SILVER)

5 3-252-827-01 SCREW (B2.6), (+) BV TAPPING6 3-254-151-01 SCREW (B2.6), (+) P TAPPING

7 2-547-158-11 HOLDER (HANDLE) (L) (BLUE)...(BLUE)

7 2-547-158-21 HOLDER (HANDLE) (L) (SILVER)...(SILVER)

8 2-547-144-11 COVER (HANDLE) (L) (BLUE)...(BLUE)(CET,RU)

8 2-547-144-21 COVER (HANDLE) (L) (SILVER)...(SILVER)

(EA,KR,MX,SP,TH)

9 2-547-124-11 HANDLE (BLUE)...(BLUE)

9 2-547-124-21 HANDLE (SILVER)...(SILVER)

10 3-252-833-01 SCREW (M3), (+) P

11 7-688-002-11 W2.6, MIDDLEANT1 1-754-376-11 ANTENNA, TELESCOPIC (FM)

The components identified by mark 0 or

dotted line with mark0 are critical for safety.

Replace only with part number specified.

1

2

2

3

4

5

5 5

5

6

7

8

9

10

ANT1

cabinet bottom section

cabinet front section

2

2

11

• Color Indicat ion of Appearance Parts

Example:

KNOB, BALANCE (WHITE) . . . (RED) R R

Parts of Color Cabinet’s Color

Ver. 1.1



CFD-S35CP


51 X-2050-349-1 CABINET (FRONT) SUB ASSY

(SILVER)...(SILVER) (EA,KR,MX,SP,TH)51 X-2050-352-1 CABINET (FRONT) SUB ASSY

(BLUE)...(BLUE) (CET,RU)

51 X-2059-483-1 CABINET (FRONT) SUB ASSY

(SILVER)...(SILVER) (AEP,UK,CET,RU)

52 3-040-916-01 FOOT (FRONT), RUBBER

53 2-547-123-11 HOLDER, CASSETTE (SILVER)...(SILVER)

53 2-547-123-21 HOLDER, CASSETTE (BLUE)...(BLUE)

54 2-547-170-01 SPRING (CASSETTE)

55 A-1101-717-A POWER KEY BOARD, COMPLETE

56 2-547-134-01 BUTTON (POWER) (SILVER)...(BLUE)

56 2-547-134-21 BUTTON (POWER) (GRAY)...(SILVER)

57 2-547-135-11 BUTTON (PAUSE) (BLUE)...(BLUE)

57 2-547-135-21 BUTTON (PAUSE) (SILVER)...(SILVER)58 3-047-468-11 DAMPER

59 3-254-070-01 SCREW

60 2-547-136-11 BUTTON (S/E) (BLUE)... (BLUE)60 2-547-136-21 BUTTON (S/E) (SILVER)...(SILVER)

61 2-547-139-11 BUTTON (REW) (BLUE).. .(BLUE)

61 2-547-139-21 BUTTON (REW) (SILVER)...(SILVER)

62 2-547-138-11 BUTTON (FF) (BLUE).. .(BLUE)

62 2-547-138-21 BUTTON (FF) (SILVER)...(SILVER)

63 2-547-141-11 BUTTON (PLAY) (BLUE)...(BLUE)

63 2-547-141-21 BUTTON (PLAY) (SILVER)...(SILVER)

64 2-547-142-11 BUTTON (REC) (BLUE)...(BLUE)

64 2-547-142-21 BUTTON (REC) (SILVER)...(SILVER)

65 3-254-151-01 SCREW (B2.6), (+) P TAPPING

66 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

SP301 1-825-690-11 SPEAKER (DIA. 10cm) (L-CH)

SP302 1-825-690-11 SPEAKER (DIA. 10cm) (R-CH)

7-2. CABINET (FRONT) SECTION

51

52

53

54

5556

5959

66

6666

66 57

60

6162

63

64

65

65

6658

SP301

SP302

Ver. 1.1



CFD-S35CP


101 3-923-736-01 COVER, CD

102 3-931-379-21 RUBBER, VIBRATION PROOF

103 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING

104 1-757-689-11 CABLE, FLEXIBLE FLAT (16 CORE)


106 3-245-709-51 SCREW

107 A-1068-202-A MP3-CD BOARD, COMPLETE

108 3-931-379-31 RUBBER, VIBRATION PROOF

109 3-253-143-01 SCREW (B2.6), (+) P TAPPING

110 3-019-395-01 PLATE, CHUCKING

111 1-452-899-11 MAGNET

112 2-547-122-31 LID, CD (BLUE)...(BLUE)

112 2-547-122-41 LID, CD (SILVER)...(SILVER)

113 2-547-171-01 SPRING (CD)

114 3-047-468-11 DAMPER

115 3-254-151-01 SCREW (B2.6), (+) P TAPPING

S801 1-692-960-11 SWITCH, PUSH (1 KEY)(Z PUSH OPEN/CLOSE)

7-3. CABINET (TOP) (1) SECTION

101

102

103

104

105

106

107

103

108

KSM-213CDP

S801109

110

111

112

113

114

115

Ver. 1.1



CFD-S35CP


7-4. CABINET (TOP) (2) SECTION

151 2-547-131-11 BUTTON (CD) (SILVER)...(BLUE)

151 2-547-131-21 BUTTON (CD) (GRAY)...(SILVER)

152 2-547-132-21 BUTTON (VOLUME) (SILVER)...(BLUE)

152 2-547-132-31 BUTTON (VOLUME) (GRAY)...(SILVER)

153 2-547-160-01 BUTTON (FUNCTION) (GRAY)...(SILVER)

153 2-547-160-21 BUTTON (FUNCTION) (SILVER)...(BLUE)


155 X-2050-351-1 BUTTON (FOLDER) SUB ASSY

156 A-1101-719-A CD KEY BOARD, COMPLETE

157 3-254-151-01 SCREW (B2.6), (+) P TAPPING

158 3-254-081-01 SCREW

159 A-1101-721-A LCD BOARD, COMPLETE

160 1-830-235-11 CABLE, FLEXIBLE FLAT (15 CORE)161 2-547-164-01 HOLDER ( LCD)

162 2-547-143-01 PLATE, LIGHT GUIDE

163 2-584-370-01 SHEET, LCD

164 2-547-133-21 BUTTON (MODE)

165 2-547-163-01 WINDOW (MP3), LCD

166 2-547-130-21 COVER (TOP) (BLUE)...(BLUE)

166 2-547-130-31 COVER (TOP) (SILVER)...(SILVER)

167 2-547-113-21 CABINET (UPPER) (BLUE)...(BLUE)

167 2-547-113-31 CABINET (UPPER) (SILVER)...(SILVER)

168 2-547-172-01 TAPE (LCD) (WINDOW)

169 2-547-165-21 ESCUTCHEON, LCD (BLUE)...(BLUE)

169 2-547-165-31 ESCUTCHEON, LCD (SILVER)...(SILVER)

170 3-250-079-01 TAPE (LCD WINDOW) (B)

171 2-594-014-01 PLATE, SUPPORT

D408 6-500-306-01 LED FA3864X (MP3)LCD401 1-805-773-11 DISPLAY PANEL, LIQUID CRYSTAL

153

152

151

154

156

157

157

171

157

157

157

155

158

158158

158

158158

159

160

169

168

170

161

162

163 164

165

166

167

LCD401not supplied

D408

157

not supplied

Ver. 1.1



CFD-S35CP

7-5. CABINET (REAR) SECTION

201

202

203

204

204

204

205

208207

206

209

210

210

210

210

211

212

213

F902

not supplied

not supplied

T901

201 2-547-120-31 CABINET (REAR) (SILVER)...(SILVER)

(EXCEPT MX)

201 2-547-120-41 CABINET (REAR) (BLUE)...(BLUE) (CET,RU)

201 2-547-120-51 CABINET (REAR) (SILVER)...(SILVER) (MX)

* 202 1-865-646-11 BATTERY-1 BOARD

203 3-240-561-02 TERMINAL (–), BATTERY

204 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING

* 205 1-865-647-11 BATTERY-2 BOARD

206 2-547-169-01 TERMINAL, ANTENNA


208 A-1098-549-A TUNER BOARD, COMPLETE (MX)

208 A-1098-590-A TUNER BOARD, COMPLETE (AEP,UK,CET,RU)208 A-1098-611-A TUNER BOARD, COMPLETE (EA,KR,SP,TH)

209 3-249-551-01 HOLDER (PWB TU)

210 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

* 211 1-725-705-11 POWER BOARD

212 A-1101-706-A HEADPHONE BOARD, COMPLETE

213 A-1101-707-A MAIN BOARD, COMPLETE (MX)

213 A-1101-730-A MAIN BOARD, COMPLETE (AEP,UK,CET)

213 A-1101-739-A MAIN BOARD, COMPLETE (EA,SP,TH)

213 A-1107-549-A MAIN BOARD, COMPLETE (KR)

213 A-1107-554-A MAIN BOARD, COMPLETE (RU)

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)

(EXCEPT MX)

0F902 1-533-469-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/250V)(MX)

0T901 1-435-917-21 TRANSFORMER, POWER (MX)0T901 1-435-918-21 TRANSFORMER, POWER (EXCEPT MX)


Ver. 1.1



CFD-S35CP

7-6. TAPE MECHANISM SECTION (MF-S350)

251

252

253254

254

255

256

257

258

HE301HRP301

M801

not supplied

C309

not supplied

not supplied

not supplied

259

260

261

251 3-237-718-01 LEVER, REC

252 3-254-022-01 SCREW


254 3-254-029-01 SCREW

255 A-1108-791-A TC BOARD, COMPLETE

256 3-252-614-01 CHASSIS, TC

257 A-1105-331-A MF-S350//C

258 3-933-825-01 ARM ASSY, PINCH ROLLER

259 3-253-143-01 SCREW (B2.6), (+) P TAPPING

260 2-189-331-01 CHASSIS, PROTECT

261 3-933-833-01 BELT, RF

C309 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

(AEP,UK,CET,RU)

HE301 1-500-813-11 HEAD, ERASE (ERASE)

HRP301 3-266-053-01 HEAD, RP (REC/PB)

M801 X-3385-048-1 MOTOR SUB ASSY (CAPSTAN/REEL)


Ver. 1.1



CFD-S35CP

7-7. CD MECHANISM SECTION (KSM-213CDP)

not supplied

M702

not supplied (M701 (SPINDLE))

303

301

302

306

304

305

0301 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)

302 2-174-500-01 SCREW (2X3)

303 2-626-908-01 SHAFT, SLED

304 2-627-003-01 GEAR (B) (RP)305 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR (SPINDLE)

(including M701)

306 2-626-907-11 GEAR (A)

M702 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)




CFD-S35CP

SECTION 8

ELECTRICAL PARTS LIST

NOTE:• Due to standardization, replacements in the

parts list may be different from the parts

specified in the diagrams or the components

used on the set.

• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

• Items marked “*” are not stocked since they

are seldom required for routine service.

Some delay should be anticipated when

ordering these items.

• CAPACITORS

uF: µF

• COILS

uH: µH

• RESISTORS

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

• SEMICONDUCTORS

In each case, u: µ, for example:

uA. . : µA. ., uPA. . : µPA. .,

uPB. . : µPB. ., uPC. . : µPC. .,

uPD. . : µPD. .

• Abbreviation

CET : East European and CSI model.


KR : Korean model.


When indicating parts by reference number,

please include the board name.

* 1-865-646-11 BATTERY-1 BOARD

***************

3-240-561-02 TERMINAL (–), BATTERY

*************************************************************

* 1-865-647-11 BATTERY-2 BOARD

***************

3-240-561-02 TERMINAL (–), BATTERY

< CONNECTOR >

CNP904 1-815-550-11 PIN, CONNECTOR (PWB) 2P

*************************************************************

A-1101-719-A CD KEY BOARD, COMPLETE

**********************

1-962-798-11 CABLE, FLEXIBLE FLAT (5 CORE)

< CAPACITOR >

C401 1-115-156-11 CERAMIC CHIP 1uF 10V

< IC >

IC402 6-600-108-01 IC RPM7140 (IR)

< RESISTOR >

R406 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R407 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R408 1-216-833-11 METAL CHIP 10K 5% 1/10W

R413 1-216-813-11 METAL CHIP 220 5% 1/10W

R414 1-216-817-11 METAL CHIP 470 5% 1/10W

R415 1-216-821-11 METAL CHIP 1K 5% 1/10W

R417 1-216-821-11 METAL CHIP 1K 5% 1/10W

R418 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R422 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R423 1-216-813-11 METAL CHIP 220 5% 1/10W

R424 1-216-817-11 METAL CHIP 470 5% 1/10W

R426 1-216-821-11 METAL CHIP 1K 5% 1/10W

R428 1-216-821-11 METAL CHIP 1K 5% 1/10W

R429 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R430 1-216-821-11 METAL CHIP 1K 5% 1/10W

R431 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R432 1-216-821-11 METAL CHIP 1K 5% 1/10W

R433 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R440 1-216-841-11 METAL CHIP 47K 5% 1/10W

R443 1-216-845-11 METAL CHIP 100K 5% 1/10W

< SWITCH >

S405 1-786-050-21 SWITCH, KEYBOARD (TAPE)

S407 1-786-050-21 SWITCH, KEYBOARD (CD)

S408 1-786-050-21 SWITCH, KEYBOARD

(RADIO•BAND•AUTO PRESET)

S409 1-786-050-21 SWITCH, KEYBOARD (SOUND)

S410 1-786-050-21 SWITCH, KEYBOARD (VOLUME –)

S411 1-786-050-21 SWITCH, KEYBOARD (MEGA BASS)

S412 1-786-050-21 SWITCH, KEYBOARD (VOLUME +)

S413 1-786-050-21 SWITCH, KEYBOARD (m /TUNE –)

S414 1-786-050-21 SWITCH, KEYBOARD (TUNE +/ M)

S415 1-786-050-21 SWITCH, KEYBOARD (. /PRESET –)

S416 1-786-050-21 SWITCH, KEYBOARD (PRESET +/ >)

S417 1-786-050-21 SWITCH, KEYBOARD (NX)

S418 1-786-050-21 SWITCH, KEYBOARD (x)

*************************************************************

A-1101-706-A HEADPHONE BOARD, COMPLETE

***************************

< CONNECTOR >

* CNP322 1-815-552-21 PIN, CONNECTOR (PWB) 4P

* CNP323 1-815-552-11 PIN, CONNECTOR (PWB) 4P

< FERRITE BEAD >

FB101 1-469-701-21 FERRITE, EMI (SMD) (1608)


< JACK >

J321 1-815-325-11 JACK (i)

< RESISTOR >

R146 1-216-809-11 METAL CHIP 100 5% 1/10W

R246 1-216-809-11 METAL CHIP 100 5% 1/10W

*************************************************************

BATTERY-1

The components identified by mark 0 or

dotted line with mark0 are critical for safety.

Replace only with part number specified.

MX : Mexican model.

RU : Russian model.


TH : Thai model.

BATTERY-2

CD KEY HEADPHONE

Ver. 1.1



CFD-S35CP


A-1101-721-A LCD BOARD, COMPLETE

********************

2-547-143-01 PLATE, LIGHT GUIDE

2-547-164-01 HOLDER (LCD)

2-584-370-01 SHEET, LCD

< CAPACITOR >

C403 1-162-974-11 CERAMIC CHIP 0.01uF 50V


C406 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V






< CONNECTOR >

CNP401 1-770-514-31 CONNECTOR, FFC/FPC 5P

< DIODE >

D405 8-719-059-97 LED L-34HD (OPR/BATT)

D407 6-500-076-01 LED SLI-343YC (BACK LIGHT)

< IC >

IC401 8-759-153-90 IC uPD7225GB-3B7

< JUMPER RESISTOR >

JC401 1-216-864-11 SHORT CHIP 0

< COIL >

L401 1-410-509-11 INDUCTOR 10uH

L402 1-414-142-61 INDUCTOR, MICRO 1uH

< LIQUID CRYSTAL DISPLAY >

LCD401 1-805-773-11 DISPLAY PANEL, LIQUID CRYSTAL

< RESISTOR >

R403 1-216-821-11 METAL CHIP 1K 5% 1/10W

R404 1-216-821-11 METAL CHIP 1K 5% 1/10W

R405 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R409 1-216-821-11 METAL CHIP 1K 5% 1/10W

R410 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R411 1-216-833-11 METAL CHIP 10K 5% 1/10W

R412 1-216-833-11 METAL CHIP 10K 5% 1/10W

R416 1-216-837-11 METAL CHIP 22K 5% 1/10W

R420 1-216-845-11 METAL CHIP 100K 5% 1/10W

R421 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R427 1-216-833-11 METAL CHIP 10K 5% 1/10W

R438 1-216-833-11 METAL CHIP 10K 5% 1/10W

R439 1-216-833-11 METAL CHIP 10K 5% 1/10W

R442 1-216-841-11 METAL CHIP 47K 5% 1/10W

R444 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R445 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR450 1-216-813-11 METAL CHIP 220 5% 1/10W

R451 1-216-813-11 METAL CHIP 220 5% 1/10W

R452 1-216-821-11 METAL CHIP 1K 5% 1/10W

R453 1-216-809-11 METAL CHIP 100 5% 1/10W

< SWITCH >

S403 1-786-050-21 SWITCH, KEYBOARD (DISP/ENT/MEMORY)

S404 1-786-050-21 SWITCH, KEYBOARD (MODE)

S421 1-786-050-21 SWITCH, KEYBOARD (FLDR +)

S422 1-786-050-21 SWITCH, KEYBOARD (FLDR –)

S423 1-786-050-21 SWITCH, KEYBOARD (REPEAT)*************************************************************

A-1101-707-A MAIN BOARD, COMPLETE (MX)

A-1101-730-A MAIN BOARD, COMPLETE (AEP,UK,CET)

A-1101-739-A MAIN BOARD, COMPLETE (EA,SP,TH)

A-1107-549-A MAIN BOARD, COMPLETE (KR)

A-1107-554-A MAIN BOARD, COMPLETE (RU)

*********************

3-254-151-01 SCREW (B2.6), (+) P TAPPING

< CAPACITOR >


C107 1-126-960-11 ELECT 1uF 20% 50VC108 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C109 1-126-947-11 ELECT 47uF 20% 35V


C111 1-104-658-11 ELECT 100uF 20% 10V

C112 1-126-926-11 ELECT 1000uF 20% 10V

C115 1-126-963-11 ELECT 4.7uF 20% 50V


C125 1-126-960-11 ELECT 1uF 20% 50V






C147 1-126-963-11 ELECT 4.7uF 20% 50V



C207 1-126-960-11 ELECT 1uF 20% 50V


C209 1-126-947-11 ELECT 47uF 20% 35V


C211 1-104-658-11 ELECT 100uF 20% 10V

C212 1-126-926-11 ELECT 1000uF 20% 10V

C215 1-126-963-11 ELECT 4.7uF 20% 50V


C225 1-126-960-11 ELECT 1uF 20% 50V






C247 1-126-963-11 ELECT 4.7uF 20% 50V



C321 1-126-926-11 ELECT 1000uF 20% 10V

C322 1-126-947-11 ELECT 47uF 20% 35V

C323 1-126-964-11 ELECT 10uF 20% 50V

C324 1-162-974-11 CERAMIC CHIP 0.01uF 50VC325 1-126-937-11 ELECT 4700uF 20% 16V

C326 1-126-923-11 ELECT 220uF 20% 10V

C327 1-126-947-11 ELECT 47uF 20% 35V

LCD MAIN

Ver. 1.1



CFD-S35CP


C328 1-126-959-11 ELECT 0.47uF 20% 50V


C330 1-126-941-11 ELECT 470uF 20% 25V

C331 1-216-923-91 ELECT 220uF 20% 10V


C333 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC334 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V







C801 1-126-947-11 ELECT 47uF 20% 35V





C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC813 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V

C814 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V







C823 1-126-964-11 ELECT 10uF 20% 50V




















C845 1-104-658-11 ELECT 100uF 20% 10V







C855 1-126-964-11 ELECT 10uF 20% 50V








C863 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC864 1-115-156-11 CERAMIC CHIP 1uF 10V


C881 1-126-963-11 ELECT 4.7uF 20% 50V

C882 1-126-963-11 ELECT 4.7uF 20% 50V



C953 1-126-925-11 ELECT 470uF 20% 10V


C959 1-126-923-11 ELECT 220uF 20% 10V


< CONNECTOR >




CNP802 1-784-776-11 CONNECTOR, FFC 15P

CNP803 1-691-043-21 HOUSING, CONNECTOR 11P



< DIODE >

D322 8-719-988-61 DIODE 1SS355TE-17

D323 8-719-988-61 DIODE 1SS355TE-17

D324 8-719-988-61 DIODE 1SS355TE-17

D801 8-719-941-86 DIODE DAN202U

D803 8-719-069-54 DIODE UDZSTE-175.1B

D804 8-719-941-09 DIODE DAP202U

D805 8-719-988-61 DIODE 1SS355TE-17

D809 8-719-988-61 DIODE 1SS355TE-17

D951 8-719-941-09 DIODE DAP202U

D953 8-719-978-33 DIODE DTZ-TT11-6.8B

D957 8-719-083-58 DIODE UDZSTE-173.9B

D958 8-719-988-61 DIODE 1SS355TE-17

< FERRITE BEAD >







< IC >

IC302 6-701-824-11 IC BD3870FS-E2

IC304 8-759-426-51 IC BA5417

IC801 6-805-405-01 IC uPD784216AGF-555-3BA-A (EXCEPT RU)

IC801 6-805-406-01 IC uPD784216AGF-556-3BA-A (RU)

IC802 6-700-336-01 IC CAT24WC02WI-1.8-TE13

IC803 6-703-285-01 IC S-812C33AUA-C2NT2G

IC804 6-705-413-01 IC BD4826G-TR

MAIN

Ver. 1.1



CFD-S35CP


< JUMPER RESISTOR >

JC303 1-216-864-11 SHORT CHIP 0 (AEP,UK,CET,KR,RU)

JC304 1-216-864-11 SHORT CHIP 0 (EA,MX,SP,TH)

JC305 1-216-864-11 SHORT CHIP 0 (EA,KR,RU,SP,TH)

JC306 1-216-864-11 SHORT CHIP 0 (AEP,UK,CET,MX)

JC309 1-216-864-11 SHORT CHIP 0 (AEP,UK,CET,KR,MX)

JC310 1-216-864-11 SHORT CHIP 0 (EA,RU,SP,TH)

JC814 1-216-864-11 SHORT CHIP 0

< COIL >

L803 1-410-509-11 INDUCTOR 10uH

L804 1-414-142-61 INDUCTOR 1uH

< TRANSISTOR >

Q122 8-729-905-40 TRANSISTOR 2SC4081T106

Q124 8-729-047-12 TRANSISTOR DTC314TU-T106

Q222 8-729-905-40 TRANSISTOR 2SC4081T106

Q224 8-729-047-12 TRANSISTOR DTC314TU-T106Q801 8-729-028-76 TRANSISTOR DTA114YUA-T106

Q802 8-729-028-76 TRANSISTOR DTA114YUA-T106

Q803 8-729-028-99 TRANSISTOR DTC114YUA-T106

Q804 8-729-028-77 TRANSISTOR DTA115EUA-T106

Q806 8-729-922-10 TRANSISTOR 2SA1577-QR

Q807 8-729-029-00 TRANSISTOR DTC115EUA-T106

Q808 8-729-905-40 TRANSISTOR 2SC4081T106


Q810 8-729-028-90 TRANSISTOR DTA143ZUA-T106


Q812 8-729-905-40 TRANSISTOR 2SC4081T106

Q813 8-729-905-40 TRANSISTOR 2SC4081T106

Q814 8-729-028-92 TRANSISTOR DTA144TUA-T106

Q815 8-729-029-00 TRANSISTOR DTC115EUA-T106

Q951 8-729-029-13 TRANSISTOR DTC143ZUA-T106

Q952 8-729-040-76 TRANSISTOR KTA1273-Y-AT

Q953 8-729-905-40 TRANSISTOR 2SC4081T106

Q955 8-729-018-99 TRANSISTOR 2SD2394-F

Q957 8-729-036-86 TRANSISTOR KTC3203Y-AT

< RESISTOR >

R101 1-216-821-11 METAL CHIP 1K 5% 1/10W

R129 1-216-817-11 METAL CHIP 470 5% 1/10W

R132 1-216-853-11 METAL CHIP 470K 5% 1/10W

R133 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R134 1-216-817-11 METAL CHIP 470 5% 1/10W

R135 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R136 1-216-821-11 METAL CHIP 1K 5% 1/10W

R137 1-216-864-11 SHORT CHIP 0

R138 1-216-817-11 METAL CHIP 470 5% 1/10W

R139 1-216-833-11 METAL CHIP 10K 5% 1/10W

R140 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R141 1-216-813-11 METAL CHIP 220 5% 1/10W

R143 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R145 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R201 1-216-821-11 METAL CHIP 1K 5% 1/10W

R229 1-216-817-11 METAL CHIP 470 5% 1/10W

R232 1-216-853-11 METAL CHIP 470K 5% 1/10W

R233 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R234 1-216-817-11 METAL CHIP 470 5% 1/10W

R235 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R236 1-216-821-11 METAL CHIP 1K 5% 1/10W

R237 1-216-864-11 SHORT CHIP 0

R238 1-216-817-11 METAL CHIP 470 5% 1/10W

R239 1-216-833-11 METAL CHIP 10K 5% 1/10WR240 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R241 1-216-813-11 METAL CHIP 220 5% 1/10W

R243 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R245 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R323 1-216-857-11 METAL CHIP 1M 5% 1/10W

R324 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R325 1-216-821-11 METAL CHIP 1K 5% 1/10W

R326 1-216-821-11 METAL CHIP 1K 5% 1/10W

R331 1-216-821-11 METAL CHIP 1K 5% 1/10W

R332 1-216-821-11 METAL CHIP 1K 5% 1/10W

R333 1-216-833-11 METAL CHIP 10K 5% 1/10W

R334 1-216-809-11 METAL CHIP 100 5% 1/10W

R335 1-216-809-11 METAL CHIP 100 5% 1/10WR801 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R802 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R803 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R804 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R805 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R806 1-216-821-11 METAL CHIP 1K 5% 1/10W

R807 1-216-821-11 METAL CHIP 1K 5% 1/10W

R808 1-216-821-11 METAL CHIP 1K 5% 1/10W

R809 1-216-821-11 METAL CHIP 1K 5% 1/10W

R810 1-216-821-11 METAL CHIP 1K 5% 1/10W

R811 1-216-821-11 METAL CHIP 1K 5% 1/10W

R812 1-216-821-11 METAL CHIP 1K 5% 1/10W

R813 1-216-821-11 METAL CHIP 1K 5% 1/10W

R814 1-216-821-11 METAL CHIP 1K 5% 1/10W

R815 1-216-821-11 METAL CHIP 1K 5% 1/10W

R816 1-216-821-11 METAL CHIP 1K 5% 1/10W

R817 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R818 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R819 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R820 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R821 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R822 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R823 1-216-821-11 METAL CHIP 1K 5% 1/10W

R824 1-216-821-11 METAL CHIP 1K 5% 1/10W

R825 1-216-833-11 METAL CHIP 10K 5% 1/10W

R826 1-216-817-11 METAL CHIP 470 5% 1/10W

R827 1-216-821-11 METAL CHIP 1K 5% 1/10W

R828 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R829 1-216-853-11 METAL CHIP 470K 5% 1/10W

R830 1-216-821-11 METAL CHIP 1K 5% 1/10W

R831 1-216-821-11 METAL CHIP 1K 5% 1/10W

R832 1-216-833-11 METAL CHIP 10K 5% 1/10W

R833 1-216-841-11 METAL CHIP 47K 5% 1/10W

R834 1-216-821-11 METAL CHIP 1K 5% 1/10W

R835 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R836 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R837 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R838 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

MAIN

Ver. 1.1



CFD-S35CP


R840 1-216-817-11 METAL CHIP 470 5% 1/10W

R841 1-216-821-11 METAL CHIP 1K 5% 1/10W

R842 1-216-821-11 METAL CHIP 1K 5% 1/10W

R843 1-216-821-11 METAL CHIP 1K 5% 1/10W

R844 1-216-817-11 METAL CHIP 470 5% 1/10W

R846 1-216-833-11 METAL CHIP 10K 5% 1/10WR847 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R848 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R849 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R850 1-216-821-11 METAL CHIP 1K 5% 1/10W

R851 1-216-833-11 METAL CHIP 10K 5% 1/10W

R852 1-216-809-11 METAL CHIP 100 5% 1/10W

R853 1-216-809-11 METAL CHIP 100 5% 1/10W

R855 1-216-817-11 METAL CHIP 470 5% 1/10W

R857 1-216-821-11 METAL CHIP 1K 5% 1/10W

R858 1-216-821-11 METAL CHIP 1K 5% 1/10W

R859 1-216-821-11 METAL CHIP 1K 5% 1/10W

R860 1-216-821-11 METAL CHIP 1K 5% 1/10W

R865 1-216-845-11 METAL CHIP 100K 5% 1/10WR866 1-216-817-11 METAL CHIP 470 5% 1/10W

R868 1-216-821-11 METAL CHIP 1K 5% 1/10W

R869 1-216-821-11 METAL CHIP 1K 5% 1/10W

R870 1-216-821-11 METAL CHIP 1K 5% 1/10W

R871 1-216-817-11 METAL CHIP 470 5% 1/10W

R872 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R873 1-216-817-11 METAL CHIP 470 5% 1/10W

R874 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R875 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R876 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R877 1-216-833-11 METAL CHIP 10K 5% 1/10W

R878 1-216-897-11 METAL CHIP 10 5% 1/10W

R879 1-216-845-11 METAL CHIP 100K 5% 1/10W

R880 1-216-849-11 METAL CHIP 220K 5% 1/10W

R881 1-216-845-11 METAL CHIP 100K 5% 1/10W

R882 1-216-845-11 METAL CHIP 100K 5% 1/10W

R883 1-216-845-11 METAL CHIP 100K 5% 1/10W

R884 1-216-817-11 METAL CHIP 470 5% 1/10W

R885 1-216-817-11 METAL CHIP 470 5% 1/10W

R886 1-216-817-11 METAL CHIP 470 5% 1/10W

R887 1-216-841-11 METAL CHIP 47K 5% 1/10W

R889 1-216-833-11 METAL CHIP 10K 5% 1/10W

R890 1-216-841-11 METAL CHIP 47K 5% 1/10W

R891 1-216-833-11 METAL CHIP 10K 5% 1/10W

R892 1-216-833-11 METAL CHIP 10K 5% 1/10W

R893 1-216-845-11 METAL CHIP 100K 5% 1/10W

R894 1-216-833-11 METAL CHIP 10K 5% 1/10W

R895 1-216-853-11 METAL CHIP 470K 5% 1/10W

R896 1-216-841-11 METAL CHIP 47K 5% 1/10W

R898 1-216-809-11 METAL CHIP 100 5% 1/10W

R899 1-216-809-11 METAL CHIP 100 5% 1/10W

R900 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R951 1-216-841-11 METAL CHIP 47K 5% 1/10W

R952 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R953 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R954 1-216-821-11 METAL CHIP 1K 5% 1/10W

R955 1-216-821-11 METAL CHIP 1K 5% 1/10W

R956 1-216-833-11 METAL CHIP 10K 5% 1/10W

R957 1-216-833-11 METAL CHIP 10K 5% 1/10W

R958 1-216-813-11 METAL CHIP 220 5% 1/10W

R959 1-216-809-11 METAL CHIP 100 5% 1/10W

R960 1-216-821-11 METAL CHIP 1K 5% 1/10W

R961 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R962 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R963 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR964 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

< VIBRATOR >

X801 1-795-526-12 VIBRATOR, CERAMIC (5MHz)

*************************************************************

A-1068-202-A MP3-CD BOARD, COMPLETE

***********************

< CAPACITOR >


C702 1-104-658-11 ELECT 100uF 20% 10V




C707 1-104-658-11 ELECT 100uF 20% 10V


C709 1-104-658-11 ELECT 100uF 20% 10V






C715 1-126-960-11 ELECT 1uF 20% 50V








C723 1-104-658-11 ELECT 100uF 20% 10V

C729 1-126-916-11 ELECT 1000uF 20% 6.3V

C730 1-126-925-11 ELECT 470uF 20% 10V














C748 1-126-925-11 ELECT 470uF 20% 10V




MP3-CDMAIN

Ver. 1.1



CFD-S35CP







C763 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC764 1-162-923-11 CERAMIC CHIP 47PF 5% 50V








C1014 1-104-658-11 ELECT 100uF 20% 10V

C1029 1 -126-916-11 ELECT 1000uF 20% 6.3V






C1054 1-126-925-11 ELECT 470uF 20% 10V













< CONNECTOR >

CNP701 1-779-553-21 CONNECTOR, FFC (LIF(NON-ZIF)) 16P


< FERRITE BEAD >










< IC >

IC701 6-701-796-01 IC LC78646E-US-E

IC702 6-701-787-11 IC BA5826FP-E2

IC1001 6-704-008-01 IC LC78684E-US-E

IC1002 6-704-009-01 IC LC32V4265CT-25-MPB-EIC1003 6-704-059-01 IC S-817B18AMC-CWHT2G

< TRANSISTOR >

Q701 8-729-054-57 TRANSISTOR KTN2907AS-RTK

< RESISTOR >

R701 1-216-841-11 METAL CHIP 47K 5% 1/10WR702 1-216-833-11 METAL CHIP 10K 5% 1/10W

R703 1-216-833-11 METAL CHIP 10K 5% 1/10W

R704 1-216-833-11 METAL CHIP 10K 5% 1/10W

R705 1-216-833-11 METAL CHIP 10K 5% 1/10W

R706 1-216-841-11 METAL CHIP 47K 5% 1/10W

R707 1-216-797-11 METAL CHIP 10 5% 1/10W

R708 1-216-833-11 METAL CHIP 10K 5% 1/10W

R709 1-216-837-11 METAL CHIP 22K 5% 1/10W

R710 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R711 1-216-813-11 METAL CHIP 220 5% 1/10W

R712 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R713 1-216-821-11 METAL CHIP 1K 5% 1/10W

R714 1-216-809-11 METAL CHIP 100 5% 1/10WR715 1-216-809-11 METAL CHIP 100 5% 1/10W

R716 1-216-809-11 METAL CHIP 100 5% 1/10W

R717 1-216-809-11 METAL CHIP 100 5% 1/10W

R718 1-216-809-11 METAL CHIP 100 5% 1/10W

R719 1-216-809-11 METAL CHIP 100 5% 1/10W

R720 1-216-809-11 METAL CHIP 100 5% 1/10W

R721 1-216-809-11 METAL CHIP 100 5% 1/10W

R722 1-216-809-11 METAL CHIP 100 5% 1/10W

R723 1-216-809-11 METAL CHIP 100 5% 1/10W

R724 1-216-841-11 METAL CHIP 47K 5% 1/10W

R725 1-216-817-11 METAL CHIP 470 5% 1/10W

R726 1-216-817-11 METAL CHIP 470 5% 1/10W

R727 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R728 1-216-833-11 METAL CHIP 10K 5% 1/10W

R729 1-216-813-11 METAL CHIP 220 5% 1/10W

R730 1-216-821-11 METAL CHIP 1K 5% 1/10W

R731 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R732 1-216-809-11 METAL CHIP 100 5% 1/10W

R733 1-216-809-11 METAL CHIP 100 5% 1/10W

R734 1-216-809-11 METAL CHIP 100 5% 1/10W

R735 1-216-809-11 METAL CHIP 100 5% 1/10W

R736 1-216-809-11 METAL CHIP 100 5% 1/10W

R737 1-216-809-11 METAL CHIP 100 5% 1/10W

R740 1-216-809-11 METAL CHIP 100 5% 1/10W

R743 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R744 1-216-845-11 METAL CHIP 100K 5% 1/10W

R745 1-216-809-11 METAL CHIP 100 5% 1/10W

R753 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R755 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R756 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R757 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R758 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R759 1-216-809-11 METAL CHIP 100 5% 1/10W

R760 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R761 1-216-805-11 METAL CHIP 47 5% 1/10W

R762 1-216-805-11 METAL CHIP 47 5% 1/10W

R763 1-216-813-11 METAL CHIP 220 5% 1/10W

R764 1-216-813-11 METAL CHIP 220 5% 1/10W

R765 1-216-841-11 METAL CHIP 47K 5% 1/10W

MP3-CD



CFD-S35CP


R766 1-216-797-11 METAL CHIP 10 5% 1/10W

R1001 1-216-809-11 METAL CHIP 100 5% 1/10W

R1002 1-216-809-11 METAL CHIP 100 5% 1/10W

R1003 1-216-809-11 METAL CHIP 100 5% 1/10W

R1004 1-216-809-11 METAL CHIP 100 5% 1/10W

R1005 1-216-809-11 METAL CHIP 100 5% 1/10WR1017 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R1018 1-216-809-11 METAL CHIP 100 5% 1/10W

R1019 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1020 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1068 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R1073 1-216-809-11 METAL CHIP 100 5% 1/10W

R1074 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1075 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1076 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1077 1-216-809-11 METAL CHIP 100 5% 1/10W

R1078 1-216-809-11 METAL CHIP 100 5% 1/10W

R1079 1-216-809-11 METAL CHIP 100 5% 1/10W

R1080 1-216-809-11 METAL CHIP 100 5% 1/10WR1081 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1082 1-216-805-11 METAL CHIP 47 5% 1/10W

< SWITCH >

S701 1-571-936-11 SWITCH, LEAF (LIMIT)

< VIBRATOR >

X701 1-795-563-21 VIBRATOR, CERAMIC (16.9MHz)

*************************************************************

* 1-725-705-11 POWER BOARD

*************

1-533-233-31 HOLDER, FUSE

< CAPACITOR >





C906 1-126-964-11 ELECT 10uF 20% 50V

< CONNECTOR >


< DIODE >

D901 8-719-063-79 DIODE 1N4002B

D902 8-719-063-79 DIODE 1N4002B

D903 8-719-063-79 DIODE 1N4002B

D904 8-719-063-79 DIODE 1N4002B

< FUSE >

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)

(EXCEPT MX)

0F902 1-533-469-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/250V)(MX)

< AC INLET >

0J901 1-526-818-11 INLET, AC (- AC IN) (MX)

0J901 1-526-838-11 INLET, AC 2P (- AC IN) (EXCEPT MX)

< TRANSFORMER >

0T901 1-435-917-21 TRANSFORMER, POWER (MX)

0T901 1-435-918-21 TRANSFORMER, POWER (EXCEPT MX)

*************************************************************

A-1101-717-A POWER KEY BOARD, COMPLETE**************************

< RESISTOR >

R401 1-216-813-11 METAL CHIP 220 5% 1/10W

R402 1-216-817-11 METAL CHIP 470 5% 1/10W

< SWITCH >

S401 1-786-050-21 SWITCH, KEYBOARD (OPERATE)

S402 1-786-050-21 SWITCH, KEYBOARD (SLEEP)

*************************************************************

A-1108-791-A TC BOARD, COMPLETE

*******************

< CAPACITOR >


C102 1-104-658-11 ELECT 100uF 20% 10V






C202 1-104-658-11 ELECT 100uF 20% 10V





C301 1-104-658-11 ELECT 100uF 20% 10V

C302 1-104-658-11 ELECT 100uF 20% 10V

C303 1-104-658-11 ELECT 100uF 20% 10V

C304 1-126-947-11 ELECT 47uF 20% 35V






< CONNECTOR >

CN303 1-784-774-11 CONNECTOR, FFC 13P

< IC >

IC301 8-759-264-71 IC TA2068N

< JUMPER RESISTOR >

JC301 1-216-864-11 SHORT CHIP 0

JC302 1-216-864-11 SHORT CHIP 0

JC303 1-216-864-11 SHORT CHIP 0

POWERMP3-CD POWER KEY TC

Ver. 1.1



CFD-S35CP


JC304 1-216-864-11 SHORT CHIP 0

JC305 1-216-864-11 SHORT CHIP 0

JC306 1-216-295-11 SHORT CHIP 0

JC307 1-216-864-11 SHORT CHIP 0

JC308 1-216-295-11 SHORT CHIP 0

JC309 1-216-864-11 SHORT CHIP 0

< TRANSISTOR >

Q301 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R

Q302 8-729-907-00 TRANSISTOR DTC114EU

Q303 8-729-907-00 TRANSISTOR DTC114EU

< RESISTOR >

R101 1-216-835-11 METAL CHIP 15K 5% 1/10W

R102 1-216-807-11 METAL CHIP 68 5% 1/10W

R103 1-216-843-11 METAL CHIP 68K 5% 1/10W

R104 1-216-835-11 METAL CHIP 15K 5% 1/10W

R105 1-216-835-11 METAL CHIP 15K 5% 1/10W

R106 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R110 1-216-809-11 METAL CHIP 100 5% 1/10W

R111 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R112 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R201 1-216-835-11 METAL CHIP 15K 5% 1/10W

R202 1-216-807-11 METAL CHIP 68 5% 1/10W

R203 1-216-843-11 METAL CHIP 68K 5% 1/10W

R204 1-216-835-11 METAL CHIP 15K 5% 1/10W

R205 1-216-835-11 METAL CHIP 15K 5% 1/10W

R206 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R210 1-216-025-11 RES-CHIP 100 5% 1/10W

R211 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R212 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R301 1-216-857-11 METAL CHIP 1M 5% 1/10W

R302 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R303 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R304 1-216-821-11 METAL CHIP 1K 5% 1/10W

R305 1-216-817-11 METAL CHIP 470 5% 1/10W

R306 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R307 1-216-797-11 METAL CHIP 10 5% 1/10W

R308 1-216-837-11 METAL CHIP 22K 5% 1/10W

R309 1-216-805-11 METAL CHIP 47 5% 1/10W

R310 1-216-857-11 METAL CHIP 1M 5% 1/10W

R311 1-216-857-11 METAL CHIP 1M 5% 1/10W

R314 1-216-817-11 METAL CHIP 470 5% 1/10W

R315 1-216-817-11 METAL CHIP 470 5% 1/10W

< SWITCH >

S301 1-786-126-11 SWITCH, SLIDE (REC/PB)

< TRANSFORMER >

T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION

*************************************************************

A-1098-549-A TUNER BOARD, COMPLETE (MX)

A-1098-611-A TUNER BOARD, COMPLETE (EA,KR,SP,TH)

**********************

2-547-169-01 TERMINAL, ANTENNA

< CAPACITOR >






C10 1-126-960-11 ELECT 1uF 20% 50V


C12 1-126-963-11 ELECT 4.7uF 20% 50V


(MX)


(EA,KR,SP,TH)


(MX)


(EA,KR,SP,TH)


(MX)

C18 1-126-923-11 ELECT 220uF 20% 10V


C21 1-126-960-11 ELECT 1uF 20% 50V


C23 1-126-960-11 ELECT 1uF 20% 50V




C29 1-104-658-11 ELECT 100uF 20% 10V













C49 1-161-051-00 CERAMIC 0.01uF 10% 25V



C53 1-137-190-11 FILM 0.22uF 5% 50V

C54 1-126-923-11 ELECT 220uF 20% 10V









TC TUNER (2 BAND)

Ver. 1.1



CFD-S35CP


C65 1-126-963-11 ELECT 4.7uF 20% 50V




(EA,KR,SP,TH)


(EA,KR,SP,TH)



< FILTER >

CF2 1-760-235-81 FILTER, CERAMIC

CF4 1-781-962-21 FILTER, CERAMIC

< CONNECTOR >


< TRIMMER CAPACITOR >

CT1 1-141-442-91 CAP, CERAMIC TRIMMER 20PF

CT3 1-141-304-21 CAP, CERAMIC TRIMMER 10PF

< DIODE >

D1 8-719-078-48 DIODE KV1471ETR-G

D2 8-719-078-48 DIODE KV1471ETR-G

D3 8-719-050-69 DIODE KV1520N

D10 8-719-988-61 DIODE 1SS355TE-17

D11 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC1 6-700-512-01 IC TA2149BN

IC2 8-759-483-40 IC LC72137M-TLM-E

< JUMPER RESISTOR >

JC1 1-216-864-11 SHORT CHIP 0

JC2 1-216-864-11 SHORT CHIP 0

JC3 1-216-864-11 SHORT CHIP 0

JC4 1-216-864-11 SHORT CHIP 0

JC5 1-216-864-11 SHORT CHIP 0

JC6 1-216-864-11 SHORT CHIP 0

JC11 1-216-864-11 SHORT CHIP 0

JC12 1-216-864-11 SHORT CHIP 0

JC13 1-216-864-11 SHORT CHIP 0

JC24 1-216-864-11 SHORT CHIP 0 (EA,KR,SP,TH)

JC33 1-216-864-11 SHORT CHIP 0

JC34 1-216-864-11 SHORT CHIP 0

< COIL >

L1 1-409-775-11 COIL, AIR-CORE


L3 1-754-117-12 ANTENNA, FERRITE-ROD (AM)

L4 1-411-234-21 COIL, AM OSC

L11 1-414-142-11 INDUCTOR 1uH (MX)

L21 1-410-509-11 INDUCTOR 10uH

< RESISTOR >

R1 1-216-817-11 METAL CHIP 470 5% 1/10W

R2 1-216-817-11 METAL CHIP 470 5% 1/10W

R3 1-216-833-11 METAL CHIP 10K 5% 1/10W

R4 1-216-833-11 METAL CHIP 10K 5% 1/10W

R5 1-216-821-11 METAL CHIP 1K 5% 1/10W

R10 1-216-805-11 METAL CHIP 47 5% 1/10W

R11 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R13 1-216-821-11 METAL CHIP 1K 5% 1/10WR14 1-216-821-11 METAL CHIP 1K 5% 1/10W

R24 1-216-813-11 METAL CHIP 220 5% 1/10W

R30 1-216-837-11 METAL CHIP 22K 5% 1/10W

R31 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R32 1-216-845-11 METAL CHIP 100K 5% 1/10W

R33 1-216-833-11 METAL CHIP 10K 5% 1/10W

R40 1-216-849-11 METAL CHIP 220K 5% 1/10W

R41 1-216-833-11 METAL CHIP 10K 5% 1/10W

R50 1-216-821-11 METAL CHIP 1K 5% 1/10W

R51 1-216-833-11 METAL CHIP 10K 5% 1/10W

R52 1-216-864-11 SHORT CHIP 0

R53 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R54 1-216-817-11 METAL CHIP 470 5% 1/10WR55 1-216-833-11 METAL CHIP 10K 5% 1/10W

R56 1-216-813-11 METAL CHIP 220 5% 1/10W

R57 1-216-809-11 METAL CHIP 100 5% 1/10W

R58 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R59 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R60 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R61 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R63 1-216-833-11 METAL CHIP 10K 5% 1/10W

R65 1-216-833-11 METAL CHIP 10K 5% 1/10W

R91 1-216-813-11 METAL CHIP 220 5% 1/10W

R92 1-216-813-11 METAL CHIP 220 5% 1/10W

R94 1-216-821-11 METAL CHIP 1K 5% 1/10W

< TRANSFORMER >

T1 1-433-741-11 TRANSFORMER, IF

T2 1-419-465-11 COIL (DET)

< VIBRATOR >

X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz)

*************************************************************

A-1098-590-A TUNER BOARD, COMPLETE (AEP,UK,CET,RU)

**********************

2-547-169-01 TERMINAL, ANTENNA

< CAPACITOR >










C10 1-126-960-11 ELECT 1uF 20% 50V


C12 1-126-963-11 ELECT 4.7uF 20% 50V

TUNER (2 BAND) TUNER (3 BAND)

Ver. 1.1



CFD-S35CP




C18 1-126-923-11 ELECT 220uF 20% 10V


C21 1-126-960-11 ELECT 1uF 20% 50V

C22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC23 1-126-960-11 ELECT 1uF 20% 50V



C29 1-104-658-11 ELECT 100uF 20% 10V









C40 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC41 1-164-230-11 CERAMIC CHIP 220PF 5% 50V







C49 1-161-772-11 CERAMIC 0.1uF 10% 25V



C53 1-137-194-81 FILM 0.47uF 5% 50V

C54 1-126-923-11 ELECT 220uF 20% 10V






















< FILTER >

CF2 1-795-426-11 FILTER, CERAMICCF4 1-781-962-21 FILTER, CERAMIC

< CONNECTOR >


< TRIMMER CAPACITOR >

CT1 1-141-442-91 CAP, CERAMIC TRIMMER 20PFCT3 1-141-304-21 CAP, CERAMIC TRIMMER 10PF

CT5 1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF

< DIODE >

D1 8-719-078-48 DIODE KV1471ETR-G

D2 8-719-078-48 DIODE KV1471ETR-G

D3 8-719-050-69 DIODE KV1520N

D10 8-719-988-61 DIODE 1SS355TE-17

D11 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC1 6-700-512-01 IC TA2149BN

IC2 8-759-483-40 IC LC72137M-TLM-E

< JUMPER RESISTOR >

JC1 1-216-864-11 SHORT CHIP 0

JC2 1-216-864-11 SHORT CHIP 0

JC3 1-216-864-11 SHORT CHIP 0

JC4 1-216-864-11 SHORT CHIP 0

JC5 1-216-864-11 SHORT CHIP 0

JC6 1-216-864-11 SHORT CHIP 0

JC22 1-216-864-11 SHORT CHIP 0

JC23 1-216-864-11 SHORT CHIP 0

JC24 1-216-864-11 SHORT CHIP 0

JC33 1-216-864-11 SHORT CHIP 0

JC34 1-216-864-11 SHORT CHIP 0

< COIL >



L3 1-754-116-12 ANTENNA, FERRITE-ROD (MW/LW)

L4 1-411-199-31 COIL, MW/LW OSC

L21 1-410-509-11 INDUCTOR 10uH

< TRANSISTOR >


Q14 8-729-905-35 TRANSISTOR 2SC4081-R

Q41 8-729-920-31 TRANSISTOR DTC343TK

Q42 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ

Q43 8-729-920-38 TRANSISTOR 2SC2059K-N

Q44 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ

Q61 8-729-106-07 FET 2SK514-H

< RESISTOR >

R1 1-216-817-11 METAL CHIP 470 5% 1/10W

R2 1-216-817-11 METAL CHIP 470 5% 1/10W

R3 1-216-833-11 METAL CHIP 10K 5% 1/10W

R4 1-216-833-11 METAL CHIP 10K 5% 1/10W

R7 1-216-853-11 METAL CHIP 470K 5% 1/10W

R9 1-216-845-11 METAL CHIP 100K 5% 1/10W

R10 1-216-805-11 METAL CHIP 47 5% 1/10W

R11 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

TUNER (3 BAND)



CFD-S35CP


R12 1-216-841-11 METAL CHIP 47K 5% 1/10W

R13 1-216-821-11 METAL CHIP 1K 5% 1/10W

R14 1-216-821-11 METAL CHIP 1K 5% 1/10W

R16 1-216-833-11 METAL CHIP 10K 5% 1/10W

R17 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R18 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR19 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R22 1-216-833-11 METAL CHIP 10K 5% 1/10W

R24 1-216-813-11 METAL CHIP 220 5% 1/10W

R30 1-216-837-11 METAL CHIP 22K 5% 1/10W

R31 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R32 1-216-845-11 METAL CHIP 100K 5% 1/10W

R33 1-216-833-11 METAL CHIP 10K 5% 1/10W

R40 1-216-853-11 METAL CHIP 470K 5% 1/10W

R41 1-216-833-11 METAL CHIP 10K 5% 1/10W

R42 1-216-845-11 METAL CHIP 100K 5% 1/10W

R43 1-216-833-11 METAL CHIP 10K 5% 1/10W

R50 1-216-821-11 METAL CHIP 1K 5% 1/10W

R51 1-216-833-11 METAL CHIP 10K 5% 1/10WR52 1-216-809-11 METAL CHIP 100 5% 1/10W

R53 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R54 1-216-817-11 METAL CHIP 470 5% 1/10W

R55 1-216-864-11 SHORT CHIP 0

R56 1-216-813-11 METAL CHIP 220 5% 1/10W

R57 1-216-809-11 METAL CHIP 100 5% 1/10W

R58 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R59 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R60 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R61 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R63 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R64 1-216-821-11 METAL CHIP 1K 5% 1/10W

R66 1-216-805-11 METAL CHIP 47 5% 1/10W

R91 1-216-813-11 METAL CHIP 220 5% 1/10W

R92 1-216-813-11 METAL CHIP 220 5% 1/10W

R93 1-216-821-11 METAL CHIP 1K 5% 1/10W

R94 1-216-821-11 METAL CHIP 1K 5% 1/10W

< TRANSFORMER >

T1 1-433-741-11 TRANSFORMER, IF

T2 1-419-465-11 COIL (DET)

< VIBRATOR >

X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz)

*************************************************************

MISCELLANEOUS

**************



111 1-452-899-11 MAGNET




0301 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)

305 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR (SPINDLE)(including M701)

ANT1 1-754-376-11 ANTENNA, TELESCOPIC (FM)


(AEP,UK,CET,RU)

D408 6-500-306-01 LED FA3864X (MP3)

HE301 1-500-813-11 HEAD, ERASE (ERASE)

HRP301 3-266-053-01 HEAD, RP (REC/PB)

M702 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)

M801 X-3385-048-1 MOTOR SUB ASSY (CAPSTAN/REEL)

S801 1-692-960-11 SWITCH, PUSH (1 KEY)

(Z PUSH OPEN/CLOSE)

SP301 1-825-690-11 SPEAKER (DIA. 10cm) (L-CH)

SP302 1-825-690-11 SPEAKER (DIA. 10cm) (R-CH)

*************************************************************

ACCESSORIES

************

0 1-590-342-12 CORD, POWER (MX)

0 1-769-412-22 CORD, POWER (EXCEPT KR,MX)

0 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)

0 1-776-985-12 CORD, POWER (KR)2-548-054-13 MANUAL, INSTRUCTION (ENGLISH)

(AEP,UK,EA,KR,SP,TH)

2-548-054-22 MANUAL, INSTRUCTION (SWEDISH) (CET)

2-548-054-32 MANUAL, INSTRUCTION (FINNISH) (CET)

2-548-054-42 MANUAL, INSTRUCTION (HUNGARIAN) (CET)

2-548-054-52 MANUAL, INSTRUCTION (CZECH) (CET)

2-548-054-62 MANUAL, INSTRUCTION (POLISH) (CET)

2-548-054-72 MANUAL, INSTRUCTION (SLOVAKIAN) (CET)

2-548-054-82 MANUAL, INSTRUCTION (RUSSIAN) (CET)

2-548-054-92 MANUAL, INSTRUCTION (SPANISH)

(AEP,SP,TH)

2-548-055-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)

(MX)

2-548-055-21 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)

(RU)

2-548-055-31 MANUAL, INSTRUCTION (ARABIC) (EA)

2-548-055-41 MANUAL, INSTRUCTION (KOREAN) (KR)

2-548-055-51 MANUAL, INSTRUCTION (FRENCH) (AEP)

2-548-055-61 MANUAL, INSTRUCTION (GERMAN) (AEP)

2-548-055-71 MANUAL, INSTRUCTION (DUTCH) (AEP)

2-548-055-81 MANUAL, INSTRUCTION (PORTUGUESE) (AEP)

3-267-151-11 LID, BATTERY (for RMT-CF15/CF15CPAD)

A-1072-200-A REMOTE COMMANDER (RMT-CF15)

(EA,KR,MX,SP,TH)

A-1127-310-A REMOTE COMMANDER (RMT-CF15CPAD)

(AEP,UK,CET,RU)

TUNER (3 BAND)

Ver. 1.1



CFD-S35CP

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision1.0 2005.04 New

1.1 2005.05 AEP and UK model addition.

Sony Cfd-s35cp Ver-1.1 Sm

Documents

Transcript of Sony Cfd-s35cp Ver-1.1 Sm