SmartSwitch Upgrade/Replacement Instructions
Transcript of SmartSwitch Upgrade/Replacement Instructions
1
KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc.
All other trademarks are property of their respective companies. The information in this document is subject to change without notice.
No company shall be liable for errors contained herein. © 2012 KVH Industries, Inc., All rights reserved. 54-0816 Rev. A
These instructions explain how to install a SmartSwitch Service/System Selector (SmartSwitch) to upgrade a TracVision HD11 system (with one HD11 antenna and ACU) or replace a previously installed SmartSwitch.
Installation Steps
Who Should Install the System?
To ensure a safe and effective installation, KVH requires that a KVH-certified marine technician install the SmartSwitch. KVH-certified technicians have the tools and electronics expertise necessary to install the system. To find a technician near you, visit www.kvh.com/wheretogetservice.
Technical Support
If you need technical assistance, please contact KVH Technical Support:
1. Inspect Parts and Gather Tools............................ 3
2. Plan the Installation............................................... 4
3. Mount the SmartSwitch........................................ 5
4. Wire the SmartSwitch ........................................... 7
5. Launch the Setup Wizard (Upgrades Only) ...... 8
Europe, Middle East, Africa, AsiaPhone: +45 45 160 180E-mail: [email protected](Mon.-Fri., 8 am-4:30 pm, +1 GMT)
North/South America, Australia, New ZealandPhone: +1 401 847-3327E-mail: [email protected](Mon.-Fri., 9 am-6 pm ET, -5 GMT)(Sat., 9 am-2 pm ET, -5 GMT)
For instructions on installing the SmartSwitch and one or two TracVision HD11 systems together, refer to the TracVision HD11 Installation Guide. For SmartSwitch operation instructions, refer to the TracVision HD11 User’s Guide.
IMPORTANT!
SmartSwitch Upgrade/Replacement Instructions
Inspect Parts and Gather Tools1
Before you begin, follow these steps to make sure you have everything you need to complete the installation.a. Unpack the box and ensure it contains everything shown on the Kitpack Contents List.
b. Carefully examine all of the supplied parts to ensure nothing was damaged in shipment.
c. Gather the following tools. You will need these tools to complete the installation.
• #1 Phillips screwdriver
• PC (preferably with Internet access)
Figure 1 SmartSwitch
Figure 2 SmartSwitch Dimensions
MULTISWITCH OUT ANTENNA INPUT
POWER PORT/A321 STBD/B
®
19.00"(48.26 cm)
16.75"(42.55 cm)
2.63"(6.68 cm)
18.31"(46.51 cm)
1.75"(4.45 cm)
0.44"(1.12 cm)
11.18"(28.40 cm)
16.31"(41.43 cm)
Side View
Front View
4 x ø.25"(0.64 cm)
Top View
Strain Relief Bracket
3
4
Plan the Installation2
Follow the steps below to plan the SmartSwitch installation.Select an Installation LocationWhen selecting an installation location, consider the following:
• Choose a belowdecks installation location that is dry, well-ventilated, and away from any heat sources or salt spray.
• The SmartSwitch must be installed within 3 feet (1 m) of the ACU A (the TracVision HD11 Antenna Control Unit (ACU) connected to Antenna A) in order to use the supplied PC data cable. However, longer cabling may be used – contact KVH for details.
Choose a Mounting OptionSelect one of the following SmartSwitch mounting options.
• You can mount the SmartSwitch in a standard 19" (48.26 cm) equipment rack, either separately or together with an ACU (see Figure 3). The SmartSwitch is 1.5U in height.
• Alternatively, you can mount the SmartSwitch to a horizontal surface; the horizontal surface mounting brackets can attach to either the top or bottom of the SmartSwitch (see Figure 3).
Figure 3 SmartSwitch Mounting Options
MULTISWITCH OUT ANTENNA INPUT
POWER PORT/A321 STBD/B
®
CONTROL UNIT MENU CHANGE ACCEPT EXIT
ANTENNA
POWER
®
T R A C K I N G S A T S
D I R E C T V 9 9 / 1 0 1 / 1 0 3
MULTISWITCH OUT ANTENNA INPUT
POWER PORT/A321 STBD/B
®
ACU/SmartSwitch Joint Rack Mount
SmartSwitch Rack Mount
Rack MountingBracket (x2)
Joint RackMounting Bracket (x2)
1.5U
3U
MULTISWITCH OUT ANTENNA INPUT
POWER PORT/A321 STBD/B
®
SmartSwitch Horizontal Surface Mount
Horizontal SurfaceMounting Bracket (x2)
Mount the SmartSwitch3
Follow the steps below to mount the SmartSwitch using the desired mounting option.Rack Mountinga. Attach the strain-relief bracket to the
SmartSwitch, as shown in Figure 4. Using a #1 Phillips screwdriver, secure the bracket in place using four #6-32 screws and #6 washers (supplied in the kitpack).
b. Secure the SmartSwitch to the rack using four M6 screws and washers (see Figure 5).
Horizontal Mountinga. Using a #1 Phillips screwdriver, remove the
six screws securing the rack mounting brackets to the SmartSwitch (see Figure 6).
b. Using a #1 Phillips screwdriver, attach the two horizontal mounting brackets to the sides of the SmartSwitch using four supplied #6-32 screws and #6 washers (see Figure 7). You can attach the brackets to either the top or bottom of the SmartSwitch, depending on your desired mounting location.
c. If you are mounting the SmartSwitch to the underside of a shelf, attach the strain-relief bracket, as shown in Figure 4. Using a #1 Phillips screwdriver, secure the bracket in place using four #6-32 screws and #6 washers (supplied in the kitpack).
d. Using fasteners appropriate for the mounting surface, secure the SmartSwitch to the mounting surface using the four mounting bracket holes.
Figure 4 Strain-Relief Bracket Mounting
Figure 5 SmartSwitch Rack Mounting
Figure 6 SmartSwitch Rack Mounting Bracket Removal
Figure 7 Horizontal Mounting
Strain-ReliefBracket
#6-32Screw (x4)
#6 Washer(x4)
MULTISWITCH OUT ANTENNA INPUT
POWER PORT/A321 STBD/B
®
MountingHole (x4)
M6 Screwand Washer (x4)
Rack MountingBracket (x2)
#6-32 Screw (x6)
Strain-ReliefBracket
HorizontalMounting Bracket (x2)
#6-32Screw (x6)
#6 Washer(x6)
5
6
Continued Mount the SmartSwitch3
Joint ACU/SmartSwitch Rack Mounting a. Using a #1 Phillips screwdriver, remove thesix screws securing the rack mounting brackets to the SmartSwitch (see Figure 6 on page 5).
b. Repeat Step a. to remove the six screws securing the rack mounting brackets to the ACU.
c. Attach the joint rack mounting brackets to the ACU and SmartSwitch, as shown in Figure 8. Secure the brackets in place using twelve #6-32 screws and washers (supplied in the kitpacks).
d. Attach the strain-relief bracket and retaining straps, as shown in Figure 8. Secure them in place using eight #6-32 screws and #6 washers (supplied in the kitpacks).
NOTE: Only the SmartSwitch strain-relief bracket must be installed. The ACU does not require a strain-relief bracket when jointly mounted with the SmartSwitch.
e. Secure the joint assembly to the rack using four M6 screws and washers.
Figure 8 ACU/SmartSwitch Joint Assembly
ACU
RetainingStrap (x2)
Joint RackMounting
Bracket (x2)
Strain-ReliefBracket
SmartSwitch
#6-32 Screw(x20)
#6 Washer(x20)
Wire the SmartSwitch4
Wiring instructions vary according to the customer’s specific system configuration and hardware. Refer to the wiring diagrams provided in Appendix A on page 9 for complete wiring instructions.NOTE: To help ensure proper cable connections, be sure to apply the cable labels (supplied in the kitpack) to the cables that will connect the SmartSwitch to other system components.
Wiring SWM and Non-SWM Hardware
Only DIRECTV® programming in North America supports SWM-compatible receivers and DVRs (see Figure 10). All linear receivers/DVRs and other circular receivers/DVRs are not SWM-compatible.
NOTE: Additional SWM-compatible receivers/DVRs might become available at any time. If your receiver or DVR model is not listed here, check its manual to see if it is SWM-compatible.
SmartSwitch Input Wiring Diagrams• One TracVision HD11 Antenna/ACU (see
page 9)
• Two TracVision HD11 Antennas/ACUs (see page 10)
SmartSwitch Output Wiring Diagrams• Overview (see page 11)
• 32 Non-SWM-compatible Tuners (see page 12)
• 16 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners (see page 13)
• 32 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners (see page 14)
Unless specified otherwise, receivers/DVRs in the following wiring diagrams are not SWM-compatible.
IMPORTANT!
Figure 9 Wiring Overview
Figure 10 SWM-Compatible Receivers/DVRs
Antenna A Antenna B(If equipped)
18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
SmartSwitch
Fuse 3.15A 250V ~ Fast Acting
Ethernet SmartSwitchController
MaintenanceRS232
To Antenna
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Red
(+48
V)
Blac
k (G
nd)
Whi
te/G
ray
Gray
/Whi
te
Whi
te/O
rang
e
Oran
ge/W
hite
Whi
te/B
row
n
Brow
n/W
hite
Whi
te/B
lue
Blue
/Whi
te
Whi
te/G
reen
Gree
n/W
hite
Red/
Oran
ge
Oran
ge/R
ed
Red/
Gree
n
Gree
n/Re
d
B (+
)
A (–
)
Wire Color/Stripe Color
WiFi
NMEASingle Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
KVH and TracVision are registered trademarks of KVH Industries, Inc.
Tested to comply with FCC Standards
Meets requirements
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
ACU A
Fuse 3.15A 250V ~ Fast Acting
Ethernet SmartSwitchController
MaintenanceRS232
To Antenna
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Red
(+48
V)
Blac
k (G
nd)
Whi
te/G
ray
Gray
/Whi
te
Whi
te/O
rang
e
Oran
ge/W
hite
Whi
te/B
row
n
Brow
n/W
hite
Whi
te/B
lue
Blue
/Whi
te
Whi
te/G
reen
Gree
n/W
hite
Red/
Oran
ge
Oran
ge/R
ed
Red/
Gree
n
Gree
n/Re
d
B (+
)
A (–
)
Wire Color/Stripe Color
WiFi
NMEASingle Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
KVH and TracVision are registered trademarks of KVH Industries, Inc.
Tested to comply with FCC Standards
Meets requirements
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
ACU B
Receiver/DVRGroup 1
Receiver/DVRGroup 3
Receiver/DVRGroup 2
*NOTE: Unlike other DVRs, the HR34 Home Media Center uses five tuners. Therefore, if you connect this DVR, be sure to reserve five tuners instead of two. Refer to the DVR’s manual for complete wiring details.
Receivers DVRs
H20 HR21, HR21 Pro
H21 HR22
H22 HR23
H23 HR24
H24 HR34/HMC*
H25 R16
D12 R20
D13 R22
7
8
Launch the Setup Wizard (Upgrades Only)5
If you are upgrading the TracVision HD11 system to include a SmartSwitch, follow the steps below to launch the Setup Wizard and reconfigure system settings. If you are replacing a previously installed SmartSwitch, the procedure is complete (your system is already configured).a. Press the power button on the front of the ACU to apply power to the TracVision system. Then wait 1 minute for system startup.
b. Open the web browser on a PC connected to the same network. Then type the ACU’s serial number into the browser’s address bar, as shown below:
http://hd11-<ACU serial number>.local
NOTE: For example, if the serial number was 123456789, you would enter the following into the browser’s address bar: http://hd11-123456789.local
TIP: The ACU serial number location is shown in Figure 12.
c. Log into the web interface:
Username: adminPassword: password
d. Select Settings/General Settings. Then select the “Launch” Button to launch the Setup Wizard (see Figure 13).
e. Follow the Setup Wizard’s onscreen instructions to reconfigure system settings (see Figure 14).
Figure 11 ACU Power Button
Figure 12 ACU Serial Number Location
Figure 13 Launch Setup Wizard Button
Figure 14 Setup Wizard
CONTROL UNIT MENU CHANGE ACCEPT EXIT
ANTENNA
POWER
®
T R A C K I N G S A T S
D I R E C T V 9 9 / 1 0 1 / 1 0 3
PowerButton
CONTROL UNIT MENU CHANGE ACCEPT EXIT
ANTENNA
POWER
®
T R A C K I N G S A T S
D I R E C T V 9 9 / 1 0 1 / 1 0 3
Serial Numberon Rear Panel123456789
Wiring DiagramsA
Wiring SmartSwitch Input: One TracVision HD11 Antenna/ACU18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
Antenna
Fuse 3.15A 250V ~ Fast Acting
Ethernet SmartSwitchController
MaintenanceRS232
To Antenna
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Red
(+48
V)
Blac
k (G
nd)
Whi
te/G
ray
Gray
/Whi
te
Whi
te/O
rang
e
Oran
ge/W
hite
Whi
te/B
row
n
Brow
n/W
hite
Whi
te/B
lue
Blue
/Whi
te
Whi
te/G
reen
Gree
n/W
hite
Red/
Oran
ge
Oran
ge/R
ed
Red/
Gree
n
Gree
n/Re
d
B (+
)
A (–
)
Wire Color/Stripe Color
WiFi
NMEASingle Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
KVH and TracVision are registered trademarks of KVH Industries, Inc.
Tested to comply with FCC Standards
Meets requirements
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Power
NetworkACU
SmartSwitch
Terminal Strip
Power/Data
18V
13V
18V/22KHz
13V/22KHz
18V 13V 18V/22KHz
13V/22KHz
SmartSwitchController
To ACU
Ferrite Clamp
Connect Cable End with Ferrite Clamp to ACU
Appendix
9
1
Continued Wiring DiagramsA
0
Wiring SmartSwitch Input: Two TracVision HD11 Antennas/ACUs
SmartSwitch
18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
Starboard Antenna (B)
Fuse 3.15A 250V ~ Fast Acting
Ethernet SmartSwitchController
MaintenanceRS232
To Antenna
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Red
(+48
V)
Blac
k (G
nd)
Whi
te/G
ray
Gray
/Whi
te
Whi
te/O
rang
e
Oran
ge/W
hite
Whi
te/B
row
n
Brow
n/W
hite
Whi
te/B
lue
Blue
/Whi
te
Whi
te/G
reen
Gree
n/W
hite
Red/
Oran
ge
Oran
ge/R
ed
Red/
Gree
n
Gree
n/Re
d
B (+
)
A (–
)
Wire Color/Stripe Color
WiFi
NMEASingle Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
KVH and TracVision are registered trademarks of KVH Industries, Inc.
Tested to comply with FCC Standards
Meets requirements
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Power
Network
Port ACU (A)
18V
13V
13V
18V/22KHz
18V/22KHz
13V/22KHz
18V 13V/22KHz
SmartSwitchController
To ACU
Fuse 3.15A 250V ~ Fast Acting
Ethernet SmartSwitchController
MaintenanceRS232
To Antenna
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Red
(+48
V)
Blac
k (G
nd)
Whi
te/G
ray
Gray
/Whi
te
Whi
te/O
rang
e
Oran
ge/W
hite
Whi
te/B
row
n
Brow
n/W
hite
Whi
te/B
lue
Blue
/Whi
te
Whi
te/G
reen
Gree
n/W
hite
Red/
Oran
ge
Oran
ge/R
ed
Red/
Gree
n
Gree
n/Re
d
B (+
)
A (–
)
Wire Color/Stripe Color
WiFi
NMEASingle Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
KVH and TracVision are registered trademarks of KVH Industries, Inc.
Tested to comply with FCC Standards
Meets requirements
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Power
Network
Starboard ACU (B)Terminal Strip
Power/Data
Port Antenna (A)
18V
13V
13V
18V/22KHz
18V/22KHz
13V/22KHz
18V 13V/22KHz
Power/Data
Terminal Strip
Ferrite Clamp
Connect Cable End with Ferrite Clamp to ACU
Continued Wiring DiagramsA
Wiring SmartSwitch Output: Overview32-Output Multiswitch*
PowerSupply
Non-SWM Receivers/DVRs(Linear, DIRECTV Latin America, DISH Network®, Bell TV, and legacy DIRECTV receivers)
Region/Service Provider #1
32-Output Multiswitch*
PowerSupply
Non-SWM Receivers/DVRs(Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
Region/Service Provider #2 DIRECTV SWM Hardware
Sat 103°/110°/119° Sat 103°/110°/119°
24 VDC IN Powerto SWM
Sat 99°/101°
+
GN
D
13V/22kHz18V/22kHz18V 13V FlexPort 1
FlexPort 2
SWM-E2
16-TunerSWM
Expander**
SWMPower
Inserter
8-Way Splitter
SWM Receivers/DVRs
SWMPower
Inserter
8-Way Splitter
SWM Receivers/DVRs
18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
SmartSwitch
Multiswitch Out 1 Multiswitch Out 2 Multiswitch Out 3
*NOTE: Similar connections apply to 16-output and 8-output multiswitches**NOTE: Similar connections apply to 32-tuner SWM expanders
Example: Wiring two non-SWM-compatible receiver/DVR groups and one SWM-compatible receiver/DVR group
11
1
Continued Wiring DiagramsA
2
Wiring SmartSwitch Output: 32 Non-SWM-compatible Tuners
18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
SmartSwitch
32-Output Multiswitch
PowerSupply
NOTE: Connections shown on this multiswitch alsoapply to 16-output and 8-output multiswitches
18V 13V
18V/22KHz
13V/22KHz
18V 13V18V/
22KHz13V/
22KHz
Additional Receivers/DVRs
SATELLITE IN
TV/ANTENNA/CABLE IN
TV SETOUT
DIGITAL AUDIOOUTPUT
S-VIDEO
ETHERNET
PHONEUSBPb Pr Y
VIDEO AUDIO R L
Receiver
Satellite In
Continued Wiring DiagramsA
Wiring SmartSwitch Output: 16 SWM-compatible Tuners and 32 Non-SWM-compatible TunersSplitter Splitter
Sat 103°/110°/119° Sat 103°/110°/119°
24 VDC IN Powerto SWM
Sat 99°/101°
+
GN
D
13V/22kHz18V/22kHz18V 13V FlexPort 1
FlexPort 2
SWM-E2
18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
SmartSwitch
16-Tuner SWM Expander
Refer to the instructions in the SWM Expander Kit for complete wiring information
Optional - To SWM Power Inserter/8-Way Splitter
VesselAC Power
SWMPower
Inserter
8-Way Splitter
SATELLITE IN(SWM-1)
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VID
EO
OU
T
DIGITAL AUDIOOUT OPTICAL
HDMI OUT
ETHERNET PHONE JACK
USB
DIRECTVSWM Receiver
Satellite In(SWM-1)
Supports up to 7 Additional TunersEach SWM Receiver = 1 TunerEach DVR = 2 Tuners
18V
13V 18V/22KHz
13V/22KHz
18V 13V
18V/22KHz
13V/22KHz
32-Output Multiswitch
PowerSupply
18V 13V18V/
22KHz13V/
22KHz
Legacy 1
Legacy 2
SWM IRD
NOTE: Connections shown on this multiswitch alsoapply to 16-output and 8-output multiswitches
Non-SWM Receivers/DVRs(Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
SWM1/PWR
SWM1/PWR
Input
Out Out
Input
Out Out
13
1
Continued Wiring DiagramsA
Wiring SmartSwitch Output: 32 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners18V 18V/22KHZ
MULTISWITCH OUT 1
13V/22KHZ13V 18V 18V/22KHZ
MULTISWITCH OUT 2
13V/22KHZ13V
18V 18V/22KHZ
PORT/A ANTENNA INPUT
13V/22KHZ13V 18V 18V/22KHZ
STARBOARD/B ANTENNA INPUT
13V/22KHZ13V
18V 18V/22KHZ
MULTISWITCH OUT 3
13V/22KHZ13V
TO ACU
SmartSwitch
Sat 103°/110°/119° Sat 103°/110°/119°
24 VDC IN Powerto SWM
Sat 99°/101°
+
GN
D
13V/22kHz18V/22kHz18V 13V
24 VDC INPowerto SWM +
FlexPort 1
FlexPort 2
SWM-E4
32-Tuner SWM Expander
Refer to the instructions in the SWM Expander Kit for complete wiring information
Optional - To SWM Power Inserter/8-Way Splitter
Optional - To SWM Power Inserter/8-Way Splitter
Optional - To SWM Power Inserter/8-Way Splitter
VesselAC Power
SWMPower
Inserter
8-Way Splitter
SATELLITE IN(SWM-1)
S-VIDEO OUT
COMPONENT OUT
AUDIO OUT
VID
EO
OU
T
DIGITAL AUDIOOUT OPTICAL
HDMI OUT
ETHERNET PHONE JACK
USB
DIRECTVSWM Receiver
Satellite In(SWM-1)
Supports up to 7 Additional TunersEach SWM Receiver = 1 TunerEach DVR = 2 Tuners
18V
13V 18V/22KHz
13V/22KHz
18V 13V
18V/22KHz
13V/22KHz
32-Output Multiswitch
PowerSupply
18V 13V18V/
22KHz13V/
22KHz
Legacy 1
Legacy 2
Legacy 1
Legacy 2SWM1/PWR
SWM IRD
NOTE: Connections shown on this multiswitch alsoapply to 16-output and 8-output multiswitches
Non-SWM Receivers/DVRs(Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
SWM1/PWR
SWM1/PWR
SWM1/PWR
4