Smart-TiltWall&WindowSystems

W I N D O W SY S T E M S

Smart - Tilt Wall and Window SystemsSmartech’s Smart - Tilt Wall and Window System is designed to be incorporated with an internal balustrade and is an operable window which allows unobtrusive views designed to tilt and rise up out of the way. This new product allows for natural environments to flow through, so that you feel like your outside, at the touch of a button.

Features• Range of glass designs• Balanced opening system• Range of powder coat colours available• Aluminium frame and tracks• Stainless steel components• Seals around perimeter frame• Bearing guide rollers

Smart Tilt - Window SystemHeight: 1600mm to 2000mmWidth: 1000mm to 4000mm Smart Tilt - Wall SystemHeight: 2200mm to 2700mmWidth: 1000mm to 4900mm

Note:These sizes apply to the standard range. All widths are subject to

variation depending on the choice of glass design and height required.

Please consult manufacture for a Window Specifications sheet along with

the code number for ordering details.

Smart - Tilt Wall or Window System OpeningSmart - Tilt Wall and Window Systems fit within the opening. Openings are to be made to the exact finished opening sizes listed in the window specifications sheet to provide snug fit at seals, smooth operation and correct tolerances. Smart. The bottom of tilt window has a double rubber seal to seal against sub sill extrusion.

Smart - Tilt Wall or Window System ConstructionThe window is manufactured as a single item with two axles attached that are connected to running bearings that are guided within a specially extruded aluminium running guide.

Note: Smartech’s products are to be installed to the structure designed to suit our fixing requirements.

Window Frame and fittingsThe window frame is an extruded aluminium profile. The frame, running guides and fittings are made from the highest quality material. Most components and fittings are made from stainless steel and all aluminium surfaces are powder coated as standard.

GlassAll glass that is supplied and fitted by Smartech is laminate safety glass as standard. (Optional) Electric switchable glass also available, where an alternative glass is required please consult manufacturer.

Note: The use of other glass or glazing material should be referred to the manufacturer due to additional weight that may or may not be required to keep the window system operating easily.

Smart - Tilt Wall & Window System

Using the Latest control Systems, the controller knows the door position at every moment of travel.

Smartech’s motorisation system is compact and unique

Natural environments to flow through inside or out, it only takes a touch of a button to have your wall open.

Large viewing Single Pane Tilt-Wall windows

LockingSmart - Tilt Wall and Window Systems are fitted with slide bolt locks on each side of the lower window. With optional motor selection no slide bolt locks will be supplied.

OperationSmart - Tilt Wall and Window Systems are balanced according to the weight of the window thus allowing easy open and close operation. Window movement is guided by bearings attached to the frame, operating in the specially extruded aluminium guides. The axles are located half way down the sides of the frame, allowing the window to pivot half in and half out of the building line.

Motorisation (Optional)Smartech’s motorisation system is compact and unique. The drive spindle shaft is made from high grade stainless steel and is hidden to ensure smooth operation. The motor turns the spindle shaft smoothly and effortlessly. Using the latest control systems, the controller knows the window position at every moment of travel. All motorised windows can be opened or closed from the touch of a button.

Key Benefits The benefits of this window system, is that no panels are stacked to one side, If you put a balustrade inside behind the window you won’t require an outside balcony, saving money on building costs, yet offering the same benefits with an internal balustrade system.

Standard Glazing Designs Smart – Tilt Window System

Single Pane – T - Window

Standard Glazing Design Smart – Tilt Wall System

Single Pane – T - Wall Double Pane – T - Wall

Smart - Tilt Window System

Smart - Tilt Wall System

MELBOURNEBRISBANE

SYDNEYPERTH

ADELAIDEHead Office & Production Facility 9 Production Road, Melton, Victoria 3337

Phone (03) 9747 9233Mobile 0403 321 840Fax (03) 9747 9448Email sales@smartechdoorsystems.com.auWeb www.smartechdoorsystems.com.au

Available From

90

SECTION VIEW THROUGH OPENING AT WINDOW1:20

INTERNAL ELEVATION: SMART-TILT WINDOW1:20

FL

DESIGN NOTES:- SHOWN IS TYPICAL SMART -TILT WINDOW VIEWED FROM INSIDE.- REFER TO SMART -TILT WINDOW DATASHEET FOR STANDARD FINISHED OPENING SIZES MATCHING EACH WINDOW DESIGN.- TYPICALLY THE OPENING TO SUIT THE WINDOW IS CONSTRUCTED FROM 90x45 & 90x35 TIMBER STUDS. - NOTE THAT 3 x 45mm WIDE STUDS ARE REQUIRED FORMING THE SIDES OF THE OPENING.- A PLINTH IS REQUIRED TO SUPPORT THE BALUSTRADE.- AN ALUMINIUM SUB SILL FITS ONTO THE PLINTH FORMING THE OPENING, IN THE CASE SHOWN, OPENING HEIGHT IS 1800mm- CEILING HEIGHT IS TAKEN AS 2700mm AND LINTEL AT 2410 ABOVE FLOOR LEVEL ( 2400 FINISHED HEIGHT). - NOTE HOWEVER THAT CEILING CAN BE LOWER AS MINIMUM HEADROOM REQUIRED IS 165mm ABOVE LINTEL, MIN. CEILING HEIGHT CAN BE REDUCED TO 2525mm.- STUD WALL OPENING WIDTH In THIS CASE IS 2220 ( 2200mm FINISHED WIDTH)- ADDITIONAL SIDE ROOM EACH SIDE OF 210mm IS REQUIRED FOR THE TRACK SYSTEM.- NOTE THE GLASS BALUSTRADE .

115

OUT

310

1765

597

25

10

761 1007

310

1670 CLEARANCE

597

130

SUB SILL

200

90

122 WINDOW

1800 OPENING

950

60

8mm CLEAR TOUGHENED GLASSBALUSTRADE

50x25 HAND RAIL

50x50 UPRIGHTS

PLINTH

SUB SILL

226

142

210 2200 OPENING 210

2220

2200 OPENING 13510

3 x 45 STUDS10

ALUMINIUM C/WEIGHT SURROUNDFULL HEIGHT

DOOR IN OPEN POSITION

575

300

1835 OPENING IN TIMBER FRAME

2700

965965 90 9090 90

SECTION VIEW THROUGH OPENING AT WINDOW1:20

INTERNAL ELEVATION: SMART-TILT WINDOW1:20

FL

DESIGN NOTES:- SHOWN IS TYPICAL SMART -TILT WINDOW VIEWED FROM INSIDE.- REFER TO SMART -TILT WINDOW DATASHEET FOR STANDARD FINISHED OPENING SIZES MATCHING EACH WINDOW DESIGN.- TYPICALLY THE OPENING TO SUIT THE WINDOW IS CONSTRUCTED FROM 90x45 & 90x35 TIMBER STUDS. - NOTE THAT 3 x 45mm WIDE STUDS ARE REQUIRED FORMING THE SIDES OF THE OPENING.- A PLINTH IS REQUIRED TO SUPPORT THE BALUSTRADE.- AN ALUMINIUM SUB SILL FITS ONTO THE PLINTH FORMING THE OPENING, IN THE CASE SHOWN, OPENING HEIGHT IS 1800mm- CEILING HEIGHT IS TAKEN AS 2700mm AND LINTEL AT 2410 ABOVE FLOOR LEVEL ( 2400 FINISHED HEIGHT). - NOTE HOWEVER THAT CEILING CAN BE LOWER AS MINIMUM HEADROOM REQUIRED IS 165mm ABOVE LINTEL, MIN. CEILING HEIGHT CAN BE REDUCED TO 2525mm.- STUD WALL OPENING WIDTH In THIS CASE IS 2220 ( 2200mm FINISHED WIDTH)- ADDITIONAL SIDE ROOM EACH SIDE OF 210mm IS REQUIRED FOR THE TRACK SYSTEM.- NOTE THE GLASS BALUSTRADE .

115

OUT

310

1765

597

25

10

761 1007

310

1670 CLEARANCE

597

130

SUB SILL

200

90

122 WINDOW

1800 OPENING

950

60

8mm CLEAR TOUGHENED GLASSBALUSTRADE

50x25 HAND RAIL

50x50 UPRIGHTS

PLINTH

SUB SILL

226

142

210 2200 OPENING 210

2220

2200 OPENING 13510

3 x 45 STUDS10

ALUMINIUM C/WEIGHT SURROUNDFULL HEIGHT

DOOR IN OPEN POSITION

575

300

1835 OPENING IN TIMBER FRAME

2700

965965 90 9090

Internal Elevation Section View Smart-TiltWindow throughopeningatwindow

W I N D O W SY S T E M S

Smart - Tilt Window System Diagram