SMART Board 8070ie-SMP interactive flat panel...
Transcript of SMART Board 8070ie-SMP interactive flat panel...
Guest laptopBottom connection panel
Side laptopconnection panel
Audio connectionpanel
Speakers
HDMI
j1
2
Inside connection
panel
c
e
< 52
' (16
m)
f
h
g
f
Appliance
SBID 8070ie-MP appliance
For cautions, warnings and other important product information see Important information for your SMART Board™ interactive display ( ).
b
a
1
Your SMART Board 8070ie-SMP interactive flat panel with appliance includes the following:• four terminal connection panels, enabling you to connect
speakers, the included appliance, a guest laptop, cabling for another guest laptop (installed solution) and other peripheral devices, such as DVD/Blu-ray ™ players and VCRs.
• SMART Meeting Pro™ software.• a SMART GoWire™ auto-launch cable with SMART
Meeting Pro software to connect to a guest laptop.• a CAT 5 USB extender to extend your USB connection up
to 52' (16 m).
smar
ttech
.com
/kb/
1701
66
SMART GoWire cable
CAT 5 USB extender(CAT5-XT-1100)
SMART Board 8070ie-SMPinteractive display
smarttech.com/kb/170132
Optional cables (not included)
Included cablesPower (country-specific)a
52' (16 m)
VGA c
Cat 5 h k VGA to RGB/HV
RS-232 n
HDMIj
52' (16 m)
Cat 5 h
SMART GoWireq
p
Required cables(not included)
m DVI HDMIj
SMART GoWiregCAT5-XT-1100f
CAT5-XT-1100
VGA dAppliance power (country-specific)
b
USBe
4 1/2' (1.4 m) 13' (4 m)
Standard cable connections SMART Board® 8070ie-SMP interactive flat panel cabling guide
© 2012 SMART Technologies ULC. All rights reserved. SMART Board, SMART Meeting Pro, SMART GoWire, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All third-party product and company names may be trademarks of their respective owners. One or more of the following patents: US6320597; US6326954; US6563491; US6741267; US6803906; US6829372; US6947032; US6954197; US6972401; US7151533; US7236162; US7411575; US7619617; US7643006; US7692625; US7755613; US7757001; US7880720; USD612396; USD616462; USD617332; and USD636784. Other patents pending. Contents are subject to change without notice. 05/2012. 1018099 Rev 01
smarttech.com/support smarttech.com/contactsupport *1018099*
Guest laptop (USB 2)
< 52
' (16
m)
f
h
VGA
k g
f
Remotely managing yourSMART Board™ 8070iinteractive displayConnecting your interactive display to an RS-232 system 2
Connection diagram 2Serial interface settings 3
Power modes 4RS-232 programming commands and responses 4
Interpreting the “invalid cmd” response 5Command inventory 5Designating video input source commands for a specific video input 6Designating a target interactive display 7
Commands and controls 8Power state commands 8Video input source 9Video source commands 10Audio output commands 13System information commands 14Service information 18
This document includes detailed instructions on how to set up your computer or room control systemto remotely manage your SMART Board™8070i interactive display using an RS-232 serial interface.
1
USB 2 HDMI/DVI Copyright SMART Technologies. All Rights Reserved.Header
Configuring the video and touch input for your SMART Board 8070i interactive display
OverviewYou can connect your SMART Board 8070i interactive display to up to three computers at once. Each computer must be connected to the interactivedisplay with a USB cable for touch input and a video cable for video input.
The following table shows the default touch input and video input pairings.
If you want to use a video and touch input pairing other than the default, you can change the video input settings in the Video and Touch Input Settingswindow of the SMART control panel.
N O T E
If multiple interactive displays are connected to your room computer, disconnect all but one of the interactive displays, and then configure the interactivedisplays one at a time.
Details
SMART hardware SMART Board 8070i interactive displays
SMART softwareSMART Notebook 10.8 SP1 collaborative learning software, SMART Meeting Pro 2.3 software and SMARTProduct Drivers 10.8
Operating systems Windows operating systems and Mac OS operating system software
Computer Touch input connection Default video input connection
Room computer USB 1 VGA
Guest laptop USB 2 RGB/HV
Side laptop USB 3 HDMI 2
Using the computer that’s connected to the USB 1 connection, configure the video input for each touch input connection using the Video and Touch InputSettings window.
I M P O R T A N T
You must have the latest version of SMART Notebook software or SMART Meeting Pro software installed on the computer connected to USB 1.
The interactive display status light must be green or flashing green.
The interactive display cannot be in Eco-Standby mode.
Page 1 of 3Configuring the video and touch input for your SMART Board 8070i interactive display (...
2/5/2012http://www.smarttech.com/us/Support/Browse+Support/Support+Documents/KB4/170065.a...
DVI
HDMI
DVI HDMI
jm
OR OR
1
ExtendingUSB ConnectionsSMART Board® 800 series interactivewhiteboards and systems
Roomcontrol
n
Bottom connection panel
Speakers
1
2
Inside connection
panel
c
e
Guest laptop (USB 3)
The USB drive connectsto the appliance.
Side laptopconnection panel
< 52
' (16
m)
h
HDMI
j
p
q
p
a
Audioconnection
panel
Appliance
SBID 8070ie-MP appliance
For cautions, warnings and other important product information see Important information for your SMART Board™ interactive display ( ).
12
b
a
smarttech.com/kb/160469
smar
ttech
.com
/kb/
1701
66
smarttech.com/kb/170132
smarttech.com/kb/170157
smarttech.com/kb/170065
smar
ttech
.com
/kb/
1701
66
Alternative cable connections