Small Products Technical Manual

Small Products Technical Manualfor Powered and Passive Panels

2

Active (Powered) Panels Part # Page4SourceSwitcherPanel SH-4SWSS 25MicPreampPanel SH-MIC 26MicPreampw/PTTPanel SH-MICPTT 27MicPreampw/PTTPanel* SH-MICPTT 28HeadphoneAmplifierPanel SH-HPB 29DualHeadphoneAmp.Panel SH-HPDUAL 30MonitorLevelControlPanel SH-LEVEL 31MonitorAmpPanel SH-AMPw/oSpeaker 32 SH-AMPSPKRw/Speaker 32Ampw/Headphone SH-AMPHPN 33DualVUMeterPanel SH-VUV(Vertical) 34 SH-VUH(Horizontal) 343MixerPanel(Input) SH-MIXER 353MixerPanel(Output) SH-MIXER 36LCDDisplayPanel SH-LCDV(Vertical) 37 SH-LCDH(Horizontal) 37In/OutBalancedMatchJack SH-DUALMATCH 38In/OutBalancedMatchJack SH-MATCHPANEL 39On/Off/CoughPanel SH-ONOFFCOUGH 40

Warranty/RepairPolicy/Returns

Table of Contents

* Obsolete Part

Part # PageStudioHub+ Standard Pinout & Power Consumptions Illustration 3HowtoPowerStudioHub+-viaPS-Cube 4HowtoPowerStudioHub+-viaaHuborWall-Wart 5

Active (Powered) MatchJacksMatchJackPreamp,Input MJ-IN 6MatchJackPreamp,Output MJ-OUT 7AES/EBUtoS/PDIFConverter MJ-SPDIFIN 8S/PDIFtoAES/EBUConverter MJ-SPDIFOUT 9 AnalogtoDigitalConverter MJ-AD 10DigitaltoAnalogConverter MJ-DA 11DigitalDistributionAmplifier MJ-DDA 12

Passive PanelsDualXLRFemaleAdapterMono/Stereo SH-2XLRF 13DualXLRMaleAdapterMono/Stereo SH-2XLRM 14DualXLRMale-FemalePanel SH-2XLRMF 15SingleXLRFemalePanel SH-1XLRF 16SingleXLRMalePanel SH-1XLRM 17SingleXLR5-PinFemalePanel SH-1XLRF5PIN 181/4”&MiniTRSPanel(Unbalanced) SH-1/4UNBAL 191/4”&MiniTRSPanel(Balanced) SH-1/4BAL 204SourceSwitcherPanel SH-4SW* 21 BreakoutAdapter ADAPT-BO 22BreakoutAdapter ADAPT-GPI 23PS-CUBE“DC-Link”PowerInserter PS-CUBE 24 MicSingleXLRFemalew/PTTPanel SH-MICPTTPAS 27

3(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StudioHub+Standard Pinout

(T568B Standard)

Current consumption for each StudioHub+ active device. Refer to this list when calculating the total number of devices that can be run together on any individual power supply.

Part # Description Current MJ-OUT Analog MatchJack Out (IHF to Pro) 75ma MJ-IN Analog MatchJack In (Pro to IHF) 35ma MJ-SPDIFOUT SPDIF OUT (S/PDIF and Optical to AES) 100ma MJ-SPDIFIN SPDIF IN (AES to S/PDIF) 0 (passive)MJ-AD Digital MatchJack A to D 150ma MJ-DA Digital MatchJack D to A 150ma MJ-DDA Digital MatchJack Distribution Amplifier 165ma* SH-DUALMATCH Dual Match Panel 100ma SH-HP Headphone Panel 100maSH-MIC Mic Pre-Amp Panel 55maSH-MIXER 3 Input Stereo Mixer with mix-minus 125ma SH-AMPSPKR Monitor Amp Panel (w/ Speaker) 1400maSH-LEVEL Monitor Panel 145maSH-VUV Dual VU Meter Panel 150maSH-LCDV LCD Display Panel 75maDA6-DC DA Hub (Single) 575maSUM4-DC Combiner Hub (Single) 175ma

+ - G - +LEFT RIGHT

Stand-Alone VersionsSome active StudioHub+ products were previously available in “Stand-Alone” versions with barrier strip connectivity for audio I/O. The following illustrates the pinout for this barrier strip.

* Powered via 9v DC (single ended) wall wart or +/-15vDC StudioHub+ power supply

+1 (615) 763-3033 • www.studiohub.com

Revised 4-21-10

4

Powering StudioHub+ Active Devices

Many StudioHub+ devices are active and are powered by +/- 15vDC. Power can be supplied via the StudioHub+ “DC-Link”system that uses CAT-5 pair #4 (White/Brown) for power, or power can be supplied via a separate power supply.See the current consumption chart to determine how many devices can be powered with different systems.

II - Powering Via a Hub (for up to 16 devices)

I - Powering via PS-Cube (for up to 4 devices)

Use any Hub in which the model number ends in “DC”(HUB18-DC or HUB36-DC or HUB8-DC or HUB16-DC

PS-EXTU

Headphone amps linktogether for audio & DC

SH-HP SH-HP

SH-MICMatchJack

D to AConverter

From 4 separateaudio sends or feeds


SH-HP

SH-MIC

MatchJack

SH-HP

PS-Cube

Power a PS-CUBE from aRadio Systems Console

Use cable # 16998(6') / 15884(1')(3-pin MTA to 3-pin MTE)

MatchJack

III - Powering via a “Wall Wart” or Desk-Top Power Supply

SH-HPSH-HP

Headphone amps link together for audio & DC.Power up to 4 headphone amps from one PS-WWU

and up to 2 headphone amps from 1 PSWW

D to AConverter

3 amp bi-polar15vDC power supply

Power a PS-CUBE from aRS Console Power Supply

Use cable # 16600(16-pin MR-16 to 5-pin MTA)

Power a PS-CUBE from aPS-EXTU Power Supply(the cable is included)

(4-pin MR-4 to 5-pin MTA)

1 Amp

1 Amp3 Amps 400 ma

Power a PS-CUBE from aPS-WWCUBE Power Supply(the captive cable is included)

(captive to 3-pin MTE)

200 ma

NOTE – All power supplies shown are Universal Voltageswitching supplies and accept from 100 to 240VAC input

power EXCEPT the “non Universal Wall-Wart”PS-WWCUBE and PS-WWSH supplies

which are 110VAC input power only.Power an individual MatchJack or Panel

from a PSWW-SH Power Supply(the captive 3-pin to MTA cable

is included)

Power multiple Panelsfrom a PSWWU-SH Power Supply

(the captive 3-pin to MTA cableis included)

Power a PS-CUBE from aPS-WWUCUBE Power Supply(the captive cable is included)


5-pin MTA & 3-pin MTEpower connectors (in parallel)

How to Power StudioHub+ - via PS-Cube

Revised 4-21-10

5

Powering StudioHub+ Active Devices

Many StudioHub+ devices are active and are powered by +/- 15vDC. Power can be supplied via the StudioHub+ “DC-Link”system that uses CAT-5 pair #4 (White/Brown) for power, or power can be supplied via a separate power supply.See the current consumption chart to determine how many devices can be powered with different systems.

II - Powering Via a Hub (for up to 16 devices)

I - Powering via PS-Cube (for up to 4 devices)

Use any Hub in which the model number ends in “DC”(HUB18-DC or HUB36-DC or HUB8-DC or HUB16-DC

PS-EXTU


SH-HP SH-HP

SH-MICMatchJack

D to AConverter

From 4 separateaudio sends or feeds


SH-HP

SH-MIC

MatchJack

SH-HP

PS-Cube

Power a PS-CUBE from aRadio Systems Console

Use cable # 16998(6') / 15884(1')(3-pin MTA to 3-pin MTE)

MatchJack

III - Powering via a “Wall Wart” or Desk-Top Power Supply

SH-HPSH-HP

Headphone amps link together for audio & DC.Power up to 4 headphone amps from one PS-WWU

and up to 2 headphone amps from 1 PSWW

D to AConverter

3 amp bi-polar15vDC power supply

Power a PS-CUBE from aRS Console Power Supply

Use cable # 16600(16-pin MR-16 to 5-pin MTA)

Power a PS-CUBE from aPS-EXTU Power Supply(the cable is included)

(4-pin MR-4 to 5-pin MTA)

1 Amp

1 Amp3 Amps 400 ma

Power a PS-CUBE from aPS-WWCUBE Power Supply(the captive cable is included)


200 ma

NOTE – All power supplies shown are Universal Voltageswitching supplies and accept from 100 to 240VAC input

power EXCEPT the “non Universal Wall-Wart”PS-WWCUBE and PS-WWSH supplies

which are 110VAC input power only.Power an individual MatchJack or Panel

from a PSWW-SH Power Supply(the captive 3-pin to MTA cable

is included)

Power multiple Panelsfrom a PSWWU-SH Power Supply

(the captive 3-pin to MTA cableis included)

Power a PS-CUBE from aPS-WWUCUBE Power Supply(the captive cable is included)


5-pin MTA & 3-pin MTEpower connectors (in parallel)

How to Power StudioHub+ - via a Hub or Wall-Wart

6

Revised 4-21-10

Part # MJ-IN StudioHub+ MatchJack Preamp, Input(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU1 Install to connect shield ground to power ground

Leftleveladjust

Rightleveladjust

AudioandpowerinputprovidedonRJ-45

Directpowerinput+/-15voltsDC

RightoutputRCAPowerLEDLeftoutputRCA


7

Revised 4-21-10

Part # MJ-OUT StudioHub+ MatchJack Preamp, Output(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com


Leftleveladjust

Rightleveladjust


RightinputRCALeftinputRCA

AudioandpowerinputprovidedonRJ-45

PowerLED


8

Revised 4-21-10

ASM STAND ALONE 12342ASM STUDIOHUB+ 12341

J1

J2

J3

R2

ASM

JU1

R1 R1

T1

Part # MJ-SPDIFIN StudioHub+ S/PDIF to AES/EBU Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

*RCAS/PDIFoutput

StudioHub+AES/EBURJ-45input

JU1

Install to connect shield ground to power ground


9

Revised 4-21-10

Part # MJ-SPDIFOUT StudioHub+ S/PDIF to AES/EBU Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

Directpowerin+/-15voltsDC

*RCAS/PDIFinput *OpticalInput

StudioHub+AES/EBUoutputandpowerin

JU1


*Useonlyone


10

Revised 10-30-15

Part # MJ-AD StudioHub+ Analog to Digital Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

DCpowerin+/-15voltsDCincluded(RadioSystemsPart#PS-UCUBE)UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s.

JU7, JU8

Install to connect RJ-45 shield to ground to power ground

Unbalanced InputsBalanced

InputAES/EBUOutput

Left Right

JU3 JU4 JU5 JU6

Set Input Level

Pro Level Input

IHF

CD

CD

CD

PRO

Set Nominal Input Sensitivity*

Shortalllowerpins

0dBuShortUpperPins ShortLowerPins ShortNoPins

+4dBu +8dBu

JU1 JU2 JU1 JU2 JU1 JU2

JU3 JU4 JU5 JU6

Set Input Level

Consumer Level Input

IHF

CD

CD

CD

PRO

Set Nominal Input Sensitivity*

Shortallupperpins

-15dBvShortUpperPins ShortLowerPins

*Setforstationstandardreferenceleveltoprovideunitoutputheadroomof20dB.

ShortNoPins-10dBv -6dBv

JU1 JU2 JU1 JU2 JU1 JU2

+15vG-15v

REDBLUWHT

PowerSupplyConnector


11

Revised 10-30-15

Part # MJ-DA StudioHub+ Digital to Analog Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

AES/EBU InputTOSlink InputCoaxial InputAnalog Output

+15vG-15v

REDBLUWHT

PowerSupplyConnector

JU1 and Ju2

Install to connect RJ-45 shield to ground

DCpowerin+/-15voltsDCincluded(RadioSystemsPart#PS-UCUBE)UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s.


12

Revised 10-30-15

(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

AESOutput#1 AESOutput#2 AESOutput#3

AESInput

AESOutput#4

JU1 - Ju5

Install to connect RJ-45 shield to ground

DCpowerin+9voltsDCincluded.(RadioSystemsPart#16213).UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s

Part # MJ-DDA StudioHub+ Digital Distribution Amplifier+1 (615) 763-3033 • www.studiohub.com

13

Revised 4-21-10

Part # SH-2XLRF StudioHub+ Dual XLR Female Adapter Mono/Stereo(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

Install JU3 to connect Left XLR pin 1 to chassis ground

Install JU4 to connect Right XLR pin 1 to chassis ground

JU1 JU2

Left RightInstall to connect XLR Pin 1 to RJ-45 shield

StudioHub+RJ45“A”formonoonlyorstereooperation

When programmed for stereo operation:L&RXLRfeedbothRJ45’sinstereo.

When programmed for Mono Operation: LeftXLRfeedsRJ45-1,pins1&2only.RightXLRfeedsRJ45-2,pins1&2only.

StudioHub+RJ45“B”forstereooperation

To configure for stereo operation

JU5

JU6

JU7, JU8, JU9, JU10

To configure for mono operation

JU5

JU6

JU7, JU8, JU9, JU10

JU1 JU2 Install to connect XLR Pin 1 to RJ-45 power ground (RJ-45 pin 4)

RJ45 shield and ground select jumpersXLR PIN1 select jumper

87654321

2 1

3

2 1

3

87654321

2 1

3

87654321

LeftXLR

RightXLR

LeftXLR

RJ-45 #1

CHASSISGROUND

RJ-45 #2JU1

JU2

RJ-45 #1

87654321

2 1

3

RightXLR

RJ-45 #2

87654321

2 1

3

2 1

3

87654321

LeftXLR

RightXLR

CHASSISGROUND

RJ-45 #2

JU3

JU1

RJ-45 #1

JU2

JU4

CHASSISGROUND

CHASSISGROUND

JU3

JU1

JU4

JU2

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

87654321

2 1

3

2 1

3

87654321

2 1

3

87654321

LeftXLR

RightXLR

LeftXLR

RJ-45 #1

CHASSISGROUND

RJ-45 #2JU1

JU2

RJ-45 #1

87654321

2 1

3

RightXLR

RJ-45 #2

87654321

2 1

3

2 1

3

87654321

LeftXLR

RightXLR

CHASSISGROUND

RJ-45 #2

JU3

JU1

RJ-45 #1

JU2

JU4

CHASSISGROUND

CHASSISGROUND

JU3

JU1

JU4

JU2

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND


14

Revised 4-21-10

Part # SH-2XLRM StudioHub+ Dual XLR Male Adapter Mono/Stereo(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StudioHub+RJ45“A”formonoonlyorstereooperation

When programmed for stereo operation:L&RXLRfeedbothRJ45’sinstereo.

When programmed for mono operation: LeftXLRfeedsRJ45-1,pins1&2only.RightXLRfeedsRJ45-2,pins1&2only.

StudioHub+RJ45“B”forstereooperation

To configure for stereo operation

JU5

JU6

JU7, JU8, JU9, JU10

To configure for mono operation

JU5

JU6

JU7, JU8, JU9, JU10

87654321

2 1

3

2 1

3

87654321

2 1

3

87654321

LeftXLR

RightXLR

LeftXLR

RJ-45 #1

CHASSISGROUND

RJ-45 #2JU1

JU2

RJ-45 #1

87654321

2 1

3

RightXLR

RJ-45 #2

87654321

2 1

3

2 1

3

87654321

LeftXLR

RightXLR

CHASSISGROUND

RJ-45 #2

JU3

JU1

RJ-45 #1

JU2

JU4

CHASSISGROUND

CHASSISGROUND

JU3

JU1

JU4

JU2

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

87654321

2 1

3

2 1

3

87654321

2 1

3

87654321

LeftXLR

RightXLR

LeftXLR

RJ-45 #1

CHASSISGROUND

RJ-45 #2JU1

JU2

RJ-45 #1

87654321

2 1

3

RightXLR

RJ-45 #2

87654321

2 1

3

2 1

3

87654321

LeftXLR

RightXLR

CHASSISGROUND

RJ-45 #2

JU3

JU1

RJ-45 #1

JU2

JU4

CHASSISGROUND

CHASSISGROUND

JU3

JU1

JU4

JU2

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND

JU1 JU2

JU1 JU2

Left Right

JU1 JU2

Install to connect XLR Pin 1 to RJ-45 shield

Install to connect XLR Pin 1 to RJ-45 power ground (RJ-45 pin 4)

RJ45 shield and ground select jumpers

Install JU3 to connect Left XLR pin 1 to chassis ground

Install JU4 to connect Right XLR pin 1 to chassis ground

XLR PIN1 select jumper


15

Revised 4-21-10

Part# SH-2XLRMF StudioHub+ Dual XLR Male/Female Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

RJ45-1 RJ45-2

FemaleXLR MaleXLR

Install JU1 to connect XLR(s) pin 1 to chassis ground

JU2

Install to connect XLR(s) pin 1 to StudioHub+ RJ45 shield

JU2

Install to connect XLR(s) pin 1 to StudioHub+ RJ45 power ground (RJ-45 pin 4)

2 1

3

87654321

FemaleXLR

RJ-45 #1

87654321

2 1

3

MaleXLR

RJ-45 #2

CHASSISGROUND

JU1

JU2

JU1

JU2

CHASSISGROUND

CHASSISGROUND

CHASSISGROUND


16

Revised 4-21-10 (Note-Thereisastereoonlyversionofthisproduct.

Seewww.studiohub.com/legacy.php)

ASSEMBLY 12044B

STUD

IOHU

B+

F XL

R TO

RJ4

5

JU4JU3

JU1

JU2

J1

J2

Part # SH-1XLRF StudioHub+ Single XLR Female Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU1

Install to connect XLR pins to chassis ground

JU2

Install to connect XLR pins to power ground

Install to connect XLR pin 1 to shield ground

JU3, JU4

Install for left and right in parallel Remove for left only

XLR


17

Revised 4-21-10(Note-Thereisastereoonlyversionofthisproduct.


ASSEMBLY 12044B

STUD

IOHU

B+

M X

LR TO

RJ4

5

JU4JU3

JU1

JU2

J1

J2

Part # SH-1XLRM StudioHub+ Single XLR Male Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU1

Install to connect XLR pins to chassis ground

JU2

Install to connect XLR pins to power ground

Install to connect XLR pin 1 to shield ground

JU3, JU4

Install for left and right in parallel Remove for left only

XLR


Modified 6-18-14

18Part # SH-1XLRF5Pin StudioHub+ Single XLR 5Pin Female Panel


JU4

Install to connect XLR pins to XLR chassis ground

Install to connect external power to light mic boom LED (5-15VDC) via pins 3 & 4 on barrier strip connector

Install to connect external power to light mic boom LED (15VDC) via pin 8 of RJ-45 when connected to a standard StudioHub+ powered Cube or Hub.

JU1, JU2

Install both jumpers to apply left and right mic audio in parallel on RJ-45 connector (StudioHub+ standard pins 1 & 2 for left, and pins 3 & 6 for right). Remove both jumpers to apply mic audio to left channel only.

5-PinXLR(Mating5-pinmalein-linemale

XLRconnectorincluded)

5-Pin XLR Pin Out

1 - Ground2 - Audio+3 - Audio–4 - LED–5 - +DCV

NOTE:UnusedStudioHub+RJ-45pin5(CAT-5wht/bluwire)isconnectedtolightmicboomLEDwhenconnectedtoground(DCvoltagemustbeprovidedeitherviabarrierstrippin4orStudioHub+pin8.ProgramJU3accordingly).

JU3

+5-1

5VDC

Gnd

Pull-

to-G

nd t

olig

ht L

EDGnd

Made for Yellowtec Mic Arms


19

Revised 4-21-10

ASSEMBLY 12362

UNBAL WORLD

GND

SHLD

SHLD

GND

SLV

L-

R-

STUDIOHUB+

JU6

JU4

JU5

JU3

JU1 JU2

J4J3

J6J5

J2J1

Part # SH-1/4UNBAL StudioHub+ 1/4” & Mini TRS Panel (Unbalanced)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU1 and JU2* Install to tie StudioHub+ RJ45 right - connection to StudioHub+ shield.

Install to tie StudioHub+ RJ45 right - connection to StudioHub+ power ground.

JU3 and JU4* Install to tie StudioHub+ RJ45 left - connection to StudioHub+ shield.

Install to tie StudioHub+ RJ45 left - connection to StudioHub+ power ground.

JU5 and JU6* Install to tie 1/4” and mini TRS sleeve to StudioHub+ RJ45 shield.

Install to tie 1/4” and mini TRS sleeve to StudioHub+ RJ45 power ground.

*Improper use of JU1, JU2, JU3, JU4 may result in no output, excessive noise, crosstalk, oscillation, or circuit failure.

StereounbalancedStudioHub+RJ45.Signalto/fromJ4andJ6

StereounbalancedStudioHub+RJ45.Signalto/fromJ3andJ5

1/4”andminiTRSJ3andJ5areinparallel.Useonlyoneatatime.

Stereounbalanced1/4”

StereounbalancedminiTRS

Stereounbalanced1/4”

StereounbalancedminiTRS1/4”andminiTRSwiring

Tip=Left+StudioHub+RJ45connection

Ring=RightStudioHub+RJ45connection

Sleeve=SeeJU5andJU6

1/4”andminiTRSJ4andJ6areinparallel.Useonlyoneatatime.


20

Revised 4-21-10

ASSEMBLY 12007

STUDIOHUB+

1/4" AND MINI TRS

JU1

J4J3

J6J5

J2J1

Part # SH-1/4BAL StudioHub+ 1/4” & Mini TRS Panel (Balanced)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

1/4”TRS&miniTRS,(J3/J4andJ5/J6)areinparallel.Useonlyoneatatime.

Leftbalanced1/4”TRS

LeftbalancedminiTRS

RightbalancedminiTRS

Rightbalanced1/4”TRS

1/4”miniTRS(J3,J4,J5,J6)wiringTip=+Ring=—Sleeve=SeeJU1pinoutsbelow

JU1 (upper pins)

Install to connect sleeve of all 1/4” and mini jacks to StudioHub+ RJ45 shield

JU1 (lower pins)

Install to connect sleeve of all 1/4” and mini jacks to StudioHub+ RJ45 power ground

2StereoStudioHub+RJ45(s)inparallel


21

Revised 01-02-13

ASSEMBLY 12013

FOUR SELECT BOARDSTUDIOHUB+

J4J3 J5J2J1

SW1

JU8JU7JU6JU5JU4JU3JU2JU1

(Obsolete Part) SH-4SW StudioHub+ 4 Source Switcher Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StereoStudioHub+RJ45

Jumpers JU1-JU8 tie +15volt and –15volt from input RJ45(s) to the output RJ45 J5

JU1 –15voltsinput1JU2 +15voltsinput1JU3 –15voltsinput2JU4 +15voltsinput2JU5 –15voltsinput3JU6 +15voltsinput3JU7 –15voltsinput4JU8 +15voltsinput4

1 2 3 4

input1 input2 input3 input4 output

Inputselects

Note:

This part obsolete as of September 2012.

Replaced by active modelSH-4SWA


22

Revised 4-21-10

ASSEMBLY 12009

STUD

IOHU

B+ B

REAK

OUT

+15V +15V

-15V

+15V-15V

-15V

SHIELD

SHIELDSHIELD

JU1

JU6JU4

JU9JU8

JU3JU2

JU7

JU5

R5R3

J1

R6R4

J3

R2R1

J2

Part # ADAPT-BO StudioHub+ Breakout Adapter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

These internal buses and jumpers allow +15volts, –15volts and shield to be connected from the two studioHub+ RJ45(s) and the termi-nal block. Acircuitpathrequiresatleasttwojumpers.

JU1installtotieterminalblockshieldtointernalshieldbus.

JU2 installtotieterminalblock–15voltstointernal–15voltbus.

JU3 installtotieterminalblock+15voltstointernal+15voltbus.

JU4 installtotieStudioHub+RJ45J2+15voltstointernal+15voltbus.

JU5 installtotieStudioHub+RJ45J2–15voltstointernal–15voltbus.

JU6 installtotieStudioHub+RJ45J3+15voltstointernal+15voltbus.

JU7 installtotieStudioHub+RJ45J3–15voltstointernal–15voltbus.

JU8 installtotieStudioHub+RJ45J2shieldtointernalshieldbus.

JU9 installtotieStudioHub+RJ45J3shieldtointernalshieldbus.

2StudioHub+RJ45withpinsbelowinparallel

1.Left+orAES/EBU+2.Left–orAES/EBU–3.Right+6.Right–4.PowerGround5.Future


Revised 3-30-11

23Part # ADAPT-GPI StudioHub+ Breakout Adapter


STUD

IOHU

B+ A

DAPT

-GPI

J3

J1J2

• • • • • • • • • • • • • • • •

RJ-45 #1 (J1)Pins 1-8

RJ-45 #2 (J2)Pins 1-8

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1RJ-45 ADAPT-GPI Pin Out for Wheatstone BLade GPIORJ-45 Pin1- Audio Ground

RJ-45 Pin2- Logic 7 In/Out






RJ-45 Pin8- +5V Digital


Revised 01-02-13

24Part # PS-CUBE StudioHub+ “DC-Link” Power Inserter


J1 J2 J3 J4

J7 J8 J9 J10

J5

J6

R1R2

R3 R4 R5 R6 R7R8

Ch. 1Aud In

Ch. 2Aud In

Ch. 3Aud In

Ch. 4Aud In

Ch. 1Aud OutPwr Out

Ch. 2Aud OutPwr Out

Ch. 3Aud OutPwr Out

Ch. 4Aud OutPwr Out

+15V-15VG

n/c +15V-15VG

n/cPowerSupply+/-15vIn(or)Out.Maxpowerprovided3amps.

PowerSupply+/-15vIn(or)OutMaxpowerprovided3amps.

PS-WW Cube Power Connector. AllowsP/NPS-WWCubeorPS-WWUCubedesktoppowersupplytoprovidepower.Maxpowerprovided400ma.

Loop-Thru Power Connector. PowersupplycableP/N11516(1ft.)required.Contactthefactorytoacquireatnochargeifneeded.

Notes:Powerisaddedtoaudioconnectionsandavailableonthe4outputRJ-45’s(J1-J4).Thefourstereoaudiofeedsarekeptseperatedandisolated.

Channelsareindependent,isolatedandindependentlyfusedwithselfresettingthermalfuses.

Powered-Side Feed to Devices

Non-Powered Input Side

PS-EXTU Power Connector. AllowsP/NPS-EXTUwall-toppowersupplytoprovidepower.Maxpowerprovided3amps.


Tomakeinputsmonosetbothjumperstolowerposition

JU1PWR

LOGIC OUTPUT

JU2

I/O B I/O A I/O 4 I/O 3 I/O 2 I/O 1

J5 J7J6

J8

JU12JU11 JU10JU9JU8JU7JU6JU5JU4JU5

J3

(I/O A & I/O B are in parallel)

1 2 3 4 G

1 2 3 4 G

DaisyChain

PGMONLY

25

Revised 07-22-15 (Note-Thereareolderversionsofthisproduct.


Part # SH-4SWSS StudioHub+ 4 Source Switcher Panel

Shielding Jumpers:JU1 –inserttoconnectpowergroundtochassisgroundJU2 –inserttoconnectpowergroundtoshield

Mono/Stereo Jumpers JU5-JU12:Tomakeinputsstereosetbothjumperstoupperposition

1 2 3 4Stereo

Mono

StudioHub+ 4 Source Switcher

TheSH-4SHSSisanactivedeviceandmustbepoweredvia+/-15VDC.PowerflowsviaStudioHub+“DC-Link”ifconnectedtoanyCat-5cablewith+/-15VDCactiveonPins7&8.Or,utilizeoptionalpowersupplyispart#PS-WWUSH.

Inputselectswillbemaintainedintheeventofapowerfailure.

InputselectswitchesmayberemotecontrolledviapinsonconnectorJ4.

Theunitisfullybidirectionalandmayswitch4inputsto1outputor1inputto4outputs

Thiscircuitboardispackagedaloneforsingle1x4use,orupto4maybeinterconnectedforuptoa1x16switchingapplication.

J5 – Programing(Note-powermustbecycledformodechange)


SpecialPurposeLogicOutputJ8(SpecialPROMrequired)

Supports3 SH-4SHSS

boards

Supports4 SH-4SHSS

boards

a b c4 switches

total

8 switchestotal

12 switchestotal

16 switchestotal

Supports1 SH-4SHSS

board

Supports2 SH-4SHSS

boards

a b c a b c a b c

a b c

Install C for momentary operation(default)

Remove C for holding

operation

a b c

1 +5VDC2 NC3 PulltoGround#1

4 PulltoGround#25 GND


26

Revised 05-06-09

3 2 1

Part # SH-MIC StudioHub+ Mic Preamp Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StudioHub+RJ45Outputandpowerin.Outputappearsonbothleft(1&2)andright(3&6)connectorpins


PowerLED XLRMicrophoneinput

JU2

XLR pin 1 select

Install to connect XLR pin 1 to RJ-45 shield.

Install to connect XLR pin 1 to power ground & J1 pin 3

JU3

Phantom Power

Off

On (+15 Volts)

JU1 Gain

26dB

46dB

66dB

OutputAudioOutput+

Output–

PowerG

round


27

11-23-16

JU1 JU2

JU5

JU12

JU8JU10

JU9

JU11

JU7

JU13

JU3JU6

JU4

10 9 8 7 6 5 4 3 2 1

Part # SH-MICPTTPLUS StudioHub+ Mic Preamp Panel with selectable mic preamplification and push-to-talk logic


JU11

Remote Barrier Strip


XLRMicrophoneInput

JU9

Push OnPush Off

Power Up with

Audio Off

JU9

Power Up with

Audio On

A A

B

JU10

A

AB

B

B

JU11

Push To Talk

JU10

A

AB

B JU11

Push To Mute

JU10AB

Push On/Push Off Jumper Settings

Mono(Pins 1, 2)

Dual Mono(Pins 1, 2, & 3, 6)

JU1 JU1

Dual Mono Jumper Settings

JU2 JU2

No Connect No Chassis Gnd

To Chassis Gnd

To DC Gnd

To RJ-45 Shield

JU4

JU4

JU4

JU6

JU6

A

A

A

B

B

B

XLR Pin 1 Ground Jumper Settings

Pre Amp Out Pre Amp In

JU3

JU5

A

A

B

B

Mic Pre In/Out Jumper Settings

JU12

JU13

A B

JU3

JU5

A

A

B

B

JU12

JU13

Off +15VDC

JU8A B

Phantom Voltage Settings

JU8

26dB 46dB 66dB

JU7AB

Mic Sensitivity Settings

JU7 JU7A AB B

Push-To-TalkSwitch

StudioHub+RJ-45Output

XLRMicrophoneOutput

• Push-To-Talk Logic• XLR Pin 1 Grounding• Dual Mono Send• Power-Up State

• Phantom Voltage• Mic Gain• Mic Pre In/Out

Set Programming Jumpers For:

Pin 1 Audio On/Off Input (pull to Gnd)Pin 2 Relay n.o. (audio not muted)Pin 3 Relay n.c. (audio muted)Pin 4 Relay CommonPin 5 Audio Output +Pin 6 Audio Output -Pin 7 Chassis GroundPin 8 GroundPin 9 -15VDCPin 10 +15VDC

A B

A

B

A B A B

A B


28

Revised 11-16-16

Part # SH-MICPTT StudioHub+ Mic Preamp w/PTT Panel Also Available with no preamplification Part # SH-MICPTTPAS StudioHub+ Mic Connector w/PTT Panel


JU1 & JU2

Isolated dry N. O. switch contacts JU4

Install to connect XLR pin 1 to chassis ground

JU1 Gain

26dB 46dB 66dB

JU2 XLR pin 1 select Install to connect XLR pin 1 to shield ground

Install to connect XLR pin 1 to power ground

Install jumper to defeat push to talk (on/off switching of mic output) Pushtotalk

Note:SpecifyonorderPushOn/PushOfformomentaryoperation

Switch“pushed”LED

JU3

Phantom Power Off On (+15 volts)

StudioHub+RJ45Outputandpowerin.Outputappearsonbothleft(1&2)andright(3&6)connectorpins

Outputaudioprovidedonbarrierstrip


Output+

Output–

ShieldGround

XLRMicrophoneinput

Note: This part obsolete as of November 2016.

Replaced by active model SH-MICPTT


29

Revised 11-23-16 (Note-Thereareolderversionsofthisproduct.


JU1

JU2

JU3

J3

J1 J2

J5

Part # SH-HPB StudioHub+ Headphone Amplifier Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

2StudioHub+RJ45inputandpoweronconnectorsinparallel


BluePowerLED

Headphonelevel 1/4”headphonejack


Gain Jumper Settings (added 3/17)

1/8”(mini)headphonejack

JU2

JU3

17.3dB 7.4dB Gain Gain


Gain Jumper Settings (added 3/17)

JU2

JU3

17.3dB 7.4dB Gain Gain

Revised 11-23-16

JU1

JU2 JU3

J1

J3 J4

30Part # SH-HPDUAL StudioHub+ Headphone Amplifier Dual Plate


J2TwoStudioHub+RJ45inputandpoweronconnectorsinparallel

J1 Directpowerinput+/-15voltsDC

PowerLED

HeadphonelevelHPAMP#1

HeadphonelevelHPAMP#2

1/4”headphonejackHPAMP#2


1/4”headphonejackHPAMP#1

StudioHub+ Heaphone Amplifier Dual Output Version

RJ-45 input jacks remain in parallel (there is only 1 input.)

Each output is isolated and at full power (with separate output amplifier chips.)

Current consumption is 100ma. All other specifications are identical to single (SH-HP) model.

30+1 (615) 763-3033 • www.studiohub.com

31

Revised 4-21-10

Part # SH-LEVEL StudioHub+ Monitor Level Control Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StereoStudioHub+RJ45(s)stereooutputandpowerin

StereoStudioHub+RJ45(s)monooutputandpowerin

LevelPowerLED

2StudioHub+RJ45inputandpowerinconnectorsinparallel


JU1

Install to connect shield ground and power ground

JU2

Install to connect shield ground and chassis ground

JU9, JU10

2 mute control connectors in parallel. Short the pins on either connector together for mute

JU3, JU4 gain select

Unity - no jumper

+10dB

+20dB

Audioandpowerinputprovidedonbarrierstrip


32

Revised 4-21-10

2 StudioHub+ RJ45 Input and power in connectors in parallel


JU2 Install to connect shield ground to chassis ground

JU4, JU5 Gain Straps Unity +10dB +20dB Gain

JU7 Mono - Stereo jumper Stereo operation

Mono operation

Left output is a mix of left and right inputs. Right output is muted

StudioHub+ Monitor Amp PanelPart # SH-AMP w/o Speaker

Part # SH-AMPSPKR w/Speaker

(Accessory Speaker) StudioHub+ Speaker Part # SH-SPKR


JU6 Mute Short these pins together to mute

J7 Left speaker

J8 Right speaker

JU3 Install for stereo operation

JU6 and JU8 Power limit

Full power

Medium power

Low powerSignalPresentLED

Levelcontrol

Directpowerin+/-15voltsDC

SpeakerOutputs

Left

Ground

Ground

Right


StudioHub+ Amp w/Headphone Part # SH-AMPHPN

StudioHub+ Speaker Part # SH-SPKR

Revised 8-02-17

33

JU1

J2

J1

J3

JU1

Install to connect RJ-45 power ground to chassis ground

J3 Speaker out (floating output - DO NOT GROUND)

16” MTE connector

J1 2 StudioHub+ RJ45 Input and power in connectors in parallel

Power LED

Level control

1/4” Headphone Output 1/8” Headphone Output (both connectors mute speaker output)

}in parallel


J2 Direct power input +/- 15 volts DC


34

Revised 4-21-10

Part # SH-VUV Dual VU Meter Panel (Vertical)

Part # SH-VUH Dual VU Meter Panel (Horizontal)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU3

Top row/left row LED input select.

Left input

Right input

JU1


JU2

Install to connect shield ground to chassis ground

2StudioHub+RJ45Inputandpowerinconnectorsinparallel

Bottomrow/rightrowLEDlevelcontrol

Toprow/rightrowLEDlevelcontrol


JU4 Bottom row/right row LED input select

Right input

Left input


35

Revised 4-21-10

No jumper for unity gain normal for +4dBu applications

+10dB gain

+20dB gain

Part # SH-MIXER StudioHub+ 3 Mixer Panel (Input Board)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StudioHub+RJ45input1andpowerin

StereoStudioHub+RJ45input2andpowerin

GainStraps(pre-fader)

JU3,JU4Input1

JU5,JU6Input2

JU7,JU8Input3


StudioHub+RJ45Input3andpowerin

JU1


JU2



36

Revised 4-21-10

ASSE

MBL

Y ST

AND

ALO

NE 1

2103

A

ASSE

MBL

Y ST

UDIO

HUB+

121

02A

STUDIOHUB+ 3 MIXER OUTPUT

J5J6

J8J7

C17

C16

C18

C19

C7C6

C5C4

U1

U3

U5

U2

U6

U4

J10

J9

J4

C2

C1

C3

J2J3

J1

D2D3

D1D4

C20

R1

C8 C12

R14

R9

R5

R10

R6

C22

R3

C10

C14

C21

R13

R2

C9 C13

R19

R16

R11

R8R7

R18

R17

C23

R15

R12

R4

C11

C15

Part # SH-MIXER StudioHub+ 3 Mixer Panel (Output Board)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

StudioHub+RJ45mixminusoutput.Mixofinputs1and2only.Alsopowerin

Inpu

t1m

ixle

vel

Inpu

t2m

ixle

vel

Inpu

t3m

ixle

vel

StudioHub+RJ45mainoutput.Mixofinputs1,2and3.Alsopowerin


37

Revised 4-21-10

Part # SH-LCDV StudioHub+ Vertical LCD Controller PanelPart # SH-LCDH StudioHub+ Horizintal LCD Controller Panel


JU1


JU2


JU3

Install/remove to reverse direction of rotary encoder

StudioHub+RJ45datainput,dataoutputandpowerin.

Directpowerinput

+/-15voltsDC

ThisboardmustbeusedinconjunctionwiththeLCDdisplayboard.

LCD DISPLAY BOARD

STUDIOHUB+

ASSEMBLY 12145A

S1C1

S2

C3

C2

ThisboardtobeusedinconjunctionwiththeLCDmicroboard

InterfacePin-Outs

RJ-45Pin-Outs Function1 TxD+2 TxD-3 RxD+6 RxD-8 +15volt4 ground


38

Revised 4-21-10

Part # SH-DUALMATCH StudioHub+ In/Out Balanced Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

JU3



JU1 and JU2

(install both the same)

Board power from J5

Board power from J4

JU4


Left Right Left RightIHFUnbalancedInput IHFUnbalancedOutput

PowerLED

RightLevel

LetLevel

RightLevel

LetLevel

BalancedOutput

andPowerIn

BalancedInputand

PowerIn

Audioin/outandpowerinputprovidedonRJ-45’s


39

Created 9-28-11

Part # SH-MATCHPANEL StudioHub+ In/Out Balanced Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com


JU1


1/8”(mini)TRSPhoneIHF

UnbalancedInput

Left&RightRCAIHF

UnbalancedInput

1/8”(mini)TRSPhoneIHFUnbalancedOutput

Left&RightRCAIHFUnbalancedOutput

PowerLED

RightLevel

LetLevel

RightLevel

LetLevel

BalancedOutput

andPower

BalancedInputand

Power

AudioinandoutandStudioHub+“DC-Link”+/-15VDCpowerprovidedonRJ-45’s


40

J2 1

2

3

4

5JU1

Created 9-13-17

Part # SH-ONOFFCOUGH StudioHub+ On/Off/Cough Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com

J2 Direct power input +15VDC (-15VDC not used)

JU1 Install to connect mic ground to chassis ground

J1 Connect Pins 4 & 5 across mixer mic input to mute audio for ON/OFF/COUGH effect.

ON/OFF/COUGH Control Panel

For use when controlling microphone when connected to music mixers (non-broadcast style consoles without GPIO control).

ON/OFF buttons will switch the mic on/off and the “COUGH” button will momentarily mute the mic audio. All buttons are LED lit to indicate status.

The panel must be provided with +15VDC. RJ-45 (StudioHub+) and barrier strip I/O connections are provided as well as +15VDC in parallel with the ON lamp to close a remote relay for speaker MUTE control.

Ground

ON (+15VDC when ON button illuminated) (use to activate muting relay)MIC Shield (in parallel with RJ-45 Shield)

MIC + (in parallel with RJ-45 Pins 1 & 3)

MIC - (in parallel with RJ-45 Pins 2 & 6)

Pin-1 – MIC +Pin-2 – MIC -Pin-3 – MIC + (in parallel with Pin-1)Pin-4 – GroundPin-5 – not usedPin-6 – MIC - (in parallel with Pin-2)Pin-7 – not usedPin-8 – +15VDC

Recommended Accessory:Use the StudioHub+ CABLE-XLRMF (or ADAPT-XLRMF) to loop the Mic signal through the panel.

RJ-45 Pin-Out



Warranty RadioSystems,Inc.,warrantsthisequipmenttobefreefromdefectsinmaterialsandworkmanshipforaperiodofone(1)year.

Thiswarrantyextendstofirstusersoftheproductandfutureownerswhopurchasetheproductwithinthewarrantyperiod.

Thetermsofthiswarrantyarenullandvoidifthisproductisstoredoroperatedinanenvironmentnotconducivetoelectronicequipment,orshowssignsofmisuseormodificationswhichaffecttheproperfunctioningoftheproduct.Thiswarrantydoesnotapplytodamagecausedbyfire,smoke,flood,lightning,oractsofnatureandphysicalabuse.

RadioSystems,Inc.,anditsassociatedcompanies,authorizeddistributors,andpersonnelarenotliableforlossofrevenuesorotherdamages,oreffectstothebroadcastsignalqualityorcoveragewhichmayresultfromthefromtheimproperfunctioningofthisproduct.

Repair Policy Technicalassistanceisavailableatanytime,atnocharge,byphoneorcorrespondence.

Duringthewarrantyperiod,therewillbenochargeforpartsorservicemadetounitswhichshownosignofmisusebycustomerorlightningcauseddamage.ThecustomerisresponsibleforthecostofshippingtheirunitbacktoRadioSystemsforrepair.

Duringthewarrantyperiod,shipmentofsmallpartsandassembliesmayalsobemadeatachargetotheuser.Emergencyshipmentsofreplacementpartsandcircuitswillbemadeattheuser’srequestforanextrashippingandservicecharge.ChargeableserviceswillbemadeCODoronNet-30daytermstouserswithestablishedaccounts.

Duringthewarrantyperiod,fullcreditorreturnofCODcharges(lessanyserviceandexpeditedshippingcharges)willbemadetouserswhoreturnthedefectivepartsorcircuitswithin30days,ifthedamageiscoveredunderthetermsofthewarranty.

Return Instructions ContactRadioSystemsforareturnauthorizationnumber.Packallitemscarefullyandshipprepaid,viaUPSinsured,to: RadioSystems,Inc.

Attn:R.A.#__________ 601HeronDrive LoganTownship,NewJersey08085-1741

Encloseanotewhichincludesyourname,company,phonenumber,theserialnumber,returnaddress(noboxnumbers),andacompletedescriptionoftheproblem.


601 Heron Drive • Logan Township, New Jersey 08085 • (856) 467-8000 • Fax (856) 467-3044

www.studiohub.com • www.radiosystems.com

Revised 08-02-2017

128 Holiday CT STE 118 • Franklin, TN 37067 +1 (615) 763-3033 • [email protected]

www.angryaudio.com • www.studiohub.com

Small Products Technical Manual

Documents

Transcript of Small Products Technical Manual