Small Flange Handle for 140G Circuit Breakers · Installation Instructions Small Flange Handle for...
2
Installation Instructions Small Flange Handle for 140G Circuit Breakers (Cat 140G-P1B; 140G-M1B; 140G-S1B) 1 2 Install GASKET Tools Needed: 7/16” #2 Phillips 3 Install BELLCRANK BRACKET and HANDLE 2 2 1 2 2 Position Lever Handle xx lb-in xx Nm xx lb-in xx Nm NOTE: FOR USE WITH CIRCUIT BREAKERS IN TYPE 1, 3, 3R, 4, 4X, 12 ENCLOSURES Hand tighten WARNING: WARNUNG: AVERTISSEMENT: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements). AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. Installation - Installazione - Instalación Instalação - -
Transcript of Small Flange Handle for 140G Circuit Breakers · Installation Instructions Small Flange Handle for...
Installation Instructions
Small Flange Handle for 140G Circuit Breakers(Cat 140G-P1B; 140G-M1B; 140G-S1B)
1 2Install GASKET
Tools
Needed:
7/16” #2 Phillips
3 Install BELLCRANK BRACKET and HANDLE
2
21
22
Position Lever Handle
xx lb-in
xx Nmxx lb-in
xx Nm
NOTE: FOR USE WITH CIRCUIT BREAKERS IN TYPE 1, 3, 3R, 4, 4X, 12 ENCLOSURES
Hand tighten
WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs.ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes.ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes.
Installation - Installazione - Instalación Instalação - -
PN-503264
DIR 10004078034 (Version 00)Copyright © 2018 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
Publication 140G-IN159A-MU-P - June 2018
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
7/16”
DEFEATER LEVER#2 PHILLIPS
7-11 lb-in
5 Assemble Washer and Hitch Pin
6 Tighten Nuts 7 Install DEFEATER LEVER
30-40 lb-in
4 Install Pin in Slot
Product certificates are located in the Rockwell Automation Literature Library: http://www.rockwellautomation.com/global/literature-library/overview.page. Publication No. 140G-CT009.
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 01Dr. DateG. USHAKOW 3-21-13
SPECIFICATIONS FOR1 OR 2 PAGE INSTRUCTION SHEET4-1/4” W x 5-1/2” H - FINAL FOLD
MATERIALSIZE
FOLD
BODY STOCK WHITEBODY INK BLACK
FLAT
8-1/2" W x 11" H 4-1/4" W x 5-1/2" H
10000021654
Final Fold
4-1/4”
5-1/2”
11”
8-1/2”
Note: After folding---Printed in (Country where printed*), part number(s) and barcode (when used) should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.
PN-123456DIR 10000000000 (Version 00)Printed in U.S.A.
BARCODE
