SL BEAM 300 FX LED Luminaire - Philipsimages.philips.com/is/content/PhilipsConsumer/PDF... · 2017....
Transcript of SL BEAM 300 FX LED Luminaire - Philipsimages.philips.com/is/content/PhilipsConsumer/PDF... · 2017....
SL BEAM 300 FXLED Luminaire
SL BEAM 300 FX LED Luminaire installation & User’s Manual
Version as of: 23rd Sep, 2015 Rev1.1
2015 Philips Group. All rights reserved.
Showline Offices
Showline - Dallas10911 Petal StreetDallas, TX 75238
Tel: 214-647-7880Fax: 214-647-8030
Showline - EuropeMarssteden 152
Enschede 7547 TDThe Netherlands
Tel: +31 53 4500424Fax: +31 53 4500425
Showline - Auckland19-21 Kawana Street
Northcote, Auckland 0627 New Zealand
Tel: +64 9 481 0100Fax: +64 9 481 0101
Showline - AsiaUnit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong RoadKwai Chung, N.T., Hong Kong
Tel: +852 2796 9786Fax: +852 2798 6545
Website:www.philips.com/showline
The material in this manual is for information purposes only and is subject to change without notice. Showline assumes no responsiblitity for any errors or omissions which may appear in this manual. For comments and suggestions regarding corrections and/or updates to this manual, please visit the Showline website at or contact yourwww.philips.com/showlinenearest Showline office.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of this document for all other purposes is specifically prohibited.
Document Number: SL BEAM 300 FX User’s Manual
Additional Resources for DMX512For more information on installing DMX512 control systems, the following publication is available for purchase from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guidefor Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT315 South Crouse Avenue, Suite 200Syracuse, NY 13210-1844Phone: 1.800.938.7488 or 1.315.463.6463www.usitt.org
Showline Limited Two-Year WarrantyShowline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the date of delivery. A copy of Showline two-year limited warranty containing specific terms and conditions can beobtained by contacting your local Showline office.
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not use outdoors.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended use.
Refer service to qualified personnel.
WARNING: You must have access to a mains circuit breaker or other power disconnect device before installing any wiring. BE sure that power is disconnected by removing fuses or turning the mains circuit breaker off before installation. Installing the device with power on may expose you to dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code����and local codes for cable specifications.Failure to use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the Nation ElectricCode and local regulations. It is also intended for installation in indoor applications only. Beforeany electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid shock or damage to the control. It is recommended that a qualified electrician perform this installation.
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
TABLE OF CONTENTS
Showline Offices Inside Front CoverIMPORTANT INFORMATION
Warnings and NoticesAdditional Resources for DMX512Showline Limited Two-Year Warranty
TABLE OF CONTENTSPREFACE
About this Manual
Included ItemsAccessories
SL BEAM 300 FX LED LUMINAIRE OVERVIEW
SL BEAM 300 FX LED Luminaire Components
SL BEAM 300 FX LED Luminaire Menu System
INSTALLATION AND SET UP
Connecting PowerConnecting SL BEAM 300 FX LED Luminaires to AC Power
Connecting to the DMX512 Network
Mounting Luminaire
OPERATION AND PROGRAMMING
LCD Display and Menu System
LCD Display and Menu System OperationSL BEAM 300 FX LED Luminaire Menu Options
PresetRecalling or Editing presets
Color Filter
Effect
Edit user Chases
Edit Rainbow
Master / Slave Operational Mode
Settings/Security
Settings/Artnet Settings
Settings/General
Settings/Display
Settings/Factory Default
Lock Fixture
Status
Settings/DMX
Password (PASSPIN)
Quick Selection Button
DMX Address
Harmonize Color CalibrationDimming Curve Selection
Strobe/Timing
Table of contents
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
2
111
4
44
5
6
78
9
10
11
1112
1212
13
13
13
1414
17
16
17
16
17
18
16
18
18
18
19
19
20
15
DMX CONTROL
Simple 8-Bit Mode
RGBW 16-Bit Mode
Simple 8-Bit Group Modes
RGBW 16-Bit Group Modes
RGBW 8-Bit Mode
RGBW 8-Bit Group Modes
SL BEAM 300 FX LED Luminaire DMX Mapping
21
28
22
32
23
27
21
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
RDM PARAMETER IDs
HSIC Mode
Pattern Mode
HSIC Group Modes
Pattern Group Modes
DMX Timing Channel Detail
SL BEAM 300 FX LED Luminaire RDM Parameter IDsCLEANING AND CARE
Special Cleaning and Care Instructions
Front Lens Cleaning
Service and Maintenance
TECHNICAL SPECIFICATIONS
Operational Specifications
Luminaire Dimensions
33
3534
38
39
45
48
48
48
49
50
3Table of contents
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
Please read all instructions before installing or using this product. Retain this manual for future reference. Additional product information and descriptions may be found on the product specification sheet.
Note: The SL BEAM 300 FX LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).
2. Included Items
3. Accessories
Each SL BEAM 300 FX LED Luminaire includes the following items:
SL BEAM 300 FX LED Luminaire
SL BEAM 300 FX LED Luminaires
Quick Start Guide
About this Manual
PC1BE - AC Power Input Cable (39 inches / 1 meter), Powercon with Bare End* (*Note, user supplies and installsown AC input connector)
SL BEAM 300 FX
QuickStart Guide
Omega Mounts
SL BEAM 300 FX LED Luminaire Accessories
Part Number Description
MC Mega Claw, Black, Anodized
SC Molded Yoke C-Clamp
HC Light Weight Half Coupler
82003 Safety Cable
Figure 1: Included Items
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
4
AC Input Cable(1m)(USA, Canada & LatinAmerica Markets Only)
AC Input Cable(1.5m)(International Markets Only)
SL BEAM 300 FX LED Luminaire Overview
1.
Major Luminaire Components
SL BEAM 300 FX LED LUMINAIRES OVERVIEW
SL BEAM 300 FX LED Luminaire Components
Snoot (Undetachable)
Luminaire Head
Luminaire Yoke
Luminaire Base Handle (x2)
Luminaire Base
LCD Display / Menu System
RJ45 Port For ArtNet
AC Output
AC Input
DMX512 / RDM Input
DMX512 / RDM Output
Bottom of Fixture Base
105mm / 4.1 in
140mm / 5.5 in4 Camlock Positions
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
5
2. LCD Display / Menu System
LCD Display / Menu System
Figure 2: LCD Display & Menu System
Note: For Menu operation and programming details, refer to "LCD Display and Menu System" on page 9..
SL BEAM 300 FX
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
CHECK MARK (Accept) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE: Menu rotates with orientation of luminaire and menu buttons are always in
the same position (with rotation of menu)
To rotate menu 180 degrees from current orientation, press and hold the two center buttons for 2 seconds.
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
6
Installation and Set Up
INSTALLATION AND SET UP
1. Power Requirements
WARNING! SL BEAM 300 FX LED Luminaires do not contain an ON/OFF switch. Always disconnect power input cable to completely remove power from the luminaire when not in use.
AC Power Operation
When connected to an AC source, the luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains an auto-ranging power supply. Each luminaire can draw up to 360 Watts.
WARNING! The maximum amount of fixtures that may be daisy-chained is (A) 4 units 100 ~ 120VAC or (B) 10 units 230 ~ 240VAC (15 Amps).
Note: For wiring of AC input connector, refer to "Connecting SL BEAM 300 FX LED Luminaires to ACPower" on page 7.
The SL BEAM 300 FX LED Luminaries operate on AC input voltages from 100 to 240 VAC.
Table 1: SL BEAM 300 FX LED Luminaire Voltage (VAC) vs. Current*
100 1803.60 2.004 7
4 7
5 8
5 9
6 9
6 10
7
5 8
110 1903.27 1.89
160 2402.25 1.50
150 2302.40 1.56
140 2202.57 1.63
130 2102.77 1.71
120 2003.00 1.80
170 2.12
Voltage (AC)
Voltage (AC)
Total Current(A)
Total Current(A)
Maximum number of units that can be linked together*
Maximum number of units that can be linked together*
WARNING! *These figures are based on the Maximum Allowable Input Current of 15 Amps (and the maximum power supply limit of 360 Watts for each connected unit). Do not overload circuits!
IMPORTANT AC POWER CONNECTION NOTE:
a. When using the daisy-chain connection method, ONLY connect SL BEAM 300 FX LED Luminaires to AC Output Connection of SL BEAM 300 FX LED Luminaires. DO NOT CONNECT OTHER TYPES OF LUMINAIRES OR DEVICES!b. Use only use approved cable types. c. Do not overload circuits!d. Do not connect SL BEAM 300 FX LED Luminaires to dimmed circuits.e. The MAXIMUM allowable number of SL BEAM 300 FX LED Luminaires which can be “daisy-chained” on one power feed are listed in Table 1, above. DO NOT EXCEED!
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
7
Connecting SL BEAM 300 FX to AC Power
Connecting SL BEAM 300 FX LED Luminaires to AC Power
If the luminaire is supplied with an AC input cable but you did not order an AC input connector, Table 2 describes how toconnect power to your SL BEAM 300 FX LED Luminaire. Field wiring of the SL BEAM 300 FX LEDLuminaire is straightforward. A total of 3 wires/conductors need to be brought to the luminaire. The following wiringscheme is required:
Figure 3: SL BEAM 300 FX LED Luminaire AC Input & Output Connections
CAUTION: In the event the AC input cable of this luminaire is damaged, it must be replaced, with an approved cable through an Authorized Showline Dealer or Service Center.
Brown Main/Line(100 to 240VAC)
Blue Neutral
Green/Yellow Ground (Earth)
Table 2: SL BEAM 300 FX LED Luminaire (IP20 Rated Models) AC Input Connections
Wire Color Purpose
2. Connecting Power
Luminaires can be powered in one of two ways:
Direct connection to a AC power source using an AC input cable. For wiring of AC input connector, refer to
Connection from the AC output of another SL BEAM 300 FX LED Luminaire. When using this method, it is very important not to connect any other type of equipment device.
WARNING! Only connect other SL BEAM 300 FX LED Luminaires to the AC Output (Thru) connector of a SL BEAM 300 FX LED Luminaire.
"Connecting SL BEAM 300 FX LED Luminaires to AC Power" below.
AC InputAC Output
Neutral
AC Input Connector (on unit)
Main /
Ground / Earth
Line
AC Connector(on side of unit)
AC Output Connector (on unit)
NeutralMain /
Ground / Earth
Line
AC Connector(on side of unit)
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
8
Connecting to the DMX512 Network
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple SL BEAM 300 FX LED Luminaires together (up to32 luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to theDMX connector on the first SL BEAM 300 FX LED Luminaire. Another cable runs from the other DMXconnector on the first unit to a DMX connector on the next SL BEAM 300 FX LED Luminaire (or DMX512device to be controlled).
Figure 4: SL BEAM 300 FX LED Luminaire DMX512 Input / Output Connections
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1 "DMX CONTROL" on page 20. For SL BEAM 300 FX LED Luminaire DMX Mapping, refer to .
Figure 5: SL BEAM 300 FX LED Luminaire - DMX512 Connections
DMX512 / RDM DMX512 / RDM
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next luminaire or DMX512
controlled device)
(from console orcontrol device)
Input ConnectorOutput Connector
DMX512 Conections
SL BEAM 300 FX LED Luminaires
DMX512 Signal
Common (Drain)
DMX512-
DMX512+
XLR Pin
Note: Remaining pins on each connector are not used.
1
2
3
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
9
Mounting Luminaire
4. Mounting Luminaire
Note: Mounting hooks, clamps, safety cables, etc. are sold separately or by others. For mounting accessoriesavailable for this product, refer to "Accessories" on page 3 .
Figure 6: Mounting the Fixture - Hanging Applications
SAFETY CABLE: Is sold separately and recommended for all hanging installation and may be required by
national and local codes. Use enclosure handles for safety cable anchor points for this fixture.
The SL BEAM 300 FX LED Luminaires are provided with the ability to hang via truss hooks, clamps, etc. (soldseparately) or floor mounted (sitting on fixture base). Securely attach a hook, clamp, etc, to each Omega Mount (twosupplied with luminaire). Attach the Omega Mounts to the luminaire base as illustrated in Figure 6 via the Camlocks.
It is recommended (and may be required by local and national safety codes) to use and install a safety cable (sold separately).
Whether hanging the fixture or free-standing on its base, be sure to leave enough space around the luminaire to allow proper, uninterrupted airflow for cooling and fixture head movement.
Luminaire Base
Omega Mount (x2)(supplied with luminaire)
Luminaire Yoke
Luminaire Head
Bottom of Fixture Base
105mm / 4.1 in
Omega Mounts
140mm / 5.5 in4 Camlock Positions
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
10
Operation and Programming
OPERATION AND PROGRAMMING
LCD Display and Menu System
The SL BEAM 300 FX LED Luminaire’s LCD Display and Menu System provides local control for accessingthe following fixture’s settings:
Presets (Standard and User Defined)
Color Filter
Effects (Chases - preloaded and user defined)
Strobe / Timing
Settings
Lock Fixture (to prevent changes)
Password
Status
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired.
Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.
SL BEAM 300 FX LED Luminaires
1.
LCD Display and Menu System Operation
The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and make changes tothe menu items. When the desired menu item is reached, press the desired Menu Button to display the menu optionsand to navigate and configure the menu options as required.
To navigate and access menu settings/selections:
Step 1. Make sure unit is powered and turned on.
Step 2. Press the desired button (as shown in Figure 7) to access menu categories.
Step 3. Use UP | DOWN | LEFT | RIGHT arrow buttons to navigate through the various options and settings.
Step 4. Make changes as desired.
Press CHECK MARK (OK) button to accept changes.
2.
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
11
LCD Display and Menu System Operation
Figure 7: LCD Display and Menu System
SL BEAM 300 FX
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
OK (Check Mark) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE: Menu rotates with orientation of Luminaire and
menu buttons are always in the same position (with rotation of menu)
To rotate menu 180 degrees manually from current
orientation, press and hold the two center buttons for 2
seconds.
3. SL BEAM 300 FX LED Luminaire Main Menu Options
Preset
Recalling or Editing Presets
Presets are stored values of the luminaire’s LED settings that can be recalled via the menu system or DMX. You can
customize up to 31 presets via the menu system.
Step 1. Select Preset from the main menu or from the preset shortcut key.
Step 2. The top left field indicates the current preset or Off, when this field is
selected (highlighted in blue), use the left and right buttons to scroll
through all presets.
Step 3. If you wish to edit the preset, use the Up and Down keys to scroll through
the parameters. Once a parameter is selected, use the left and right arrow
buttons to make adjustments.
To recall or edit presets
Edit a PresetH
S
I
C
12%
0%
43%
HSI Mode
Edit a Preset
Notes:
. If security features are enabled, the Up and Down arrows will have no effect. See “Settings/Security” on page 15.
. Depending on the DMX map set assigned the DMX menu, different either RGBW or HSIC parameters will be available.
Step 4. Once all values are adjusted as desired, press the Check Mark button to save the preset.
Step 5. The Save Preset Menu option will appear. Use the left and right arrow buttons to select the preset number to save to.
Note: This function allows you to save your current edits to a different preset number than you began editing. This is helpful to create copies of existing presets.
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
12
Step 6. Press the Check Mark button to save the preset. You will be asked to confirm your saving operation.
Step 7. The preset is now saved and can be recalled via the menu or DMX.
To recall a color filter from the menu:
Step 1. Select Color Filter from the main menu.
Step 2. The top indicates the current color filter or Off, when this field is selected (highlighted in blue), use the left
and right buttons to scroll through all color filters.
Step 3. Use the Up and Down arrow keys to toggle to the Master Intensity field. use the Left and Right arrow keys
to adjust the Master Intensity.
Step 4. The menu will display a graphical indication of the color along with the color name.
Note: The color filter will remain ON until you select a preset, chase, other color filter or send the unit DMX.
Color Filter
Effects
Editing User Chases
Color filters are 43 factory made colors that utilize the Harmonize Color Calibration system (refer to “HarmonizeColor Calibration” on page 19 for more information). They can be recalled via the menu system or DMX.
Effects are chases stored values of the luminaire’s LED settings that can be recalled via the menu system or DMX.
There are 10 factory defined chases and eight user adjustable chases. You can adjust the master intensity, speed, and
fade values for any of the 18 chases.
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the different general
fixture settings. When finished, press the Check button to exit the menu level. The adjustable parameters are
described in Table 3.
Eight User chases can be further customized to create different effects on the
fixture. To edit a User Chase, first use the up and down arrows to scroll to the Edit
User Chase field and then press the Check Mark button. The Edit User Chase
window will be displayed:
Use the Up and Down buttons to select parameters and the Left and Right buttons
to assign the different general fixture settings. When finished, press the Check
button to exit the menu level. The adjustable parameters are described in Table 4.
Table 3: Effects parameters
Table 4: User Chase parameters
ParameterUser Chase / Built-in Chase Select from the 18 different chases.
Master Intensity Ajust the master intensity for ALL chases.
Total Steps Displays the total steps used by the chase. This field is not editable.
Speed The total time each step of the chase will be recalled.
Fade The percentage of the time assigned by the speed that is crossfaded between steps.
Description
Parameter
User Chase Select which chase you wish to edit.
Press the Check mark button to display the Rainbow Chase editor.
Total Steps Displays the total steps used by the chase. This field is not editable.
Edit Step Select a step to edit with the left right arrow buttons. Press the Check Mark button to edit the step. (see )To edit and save a Step
New Step Add a step to the end of the chase. Press the Check Mark button to edit the new step (see )To edit and save a Step
Delete Step
Rainbow
Delete the currently selected step in the Edit Step field. Press the Check mark button to delete the current step.
Description
Built In Chase 8
Total Steps
Speed
Fade
24
8 S
70%
Edit a Chase
Operation and Programming
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
13
To edit and save a Step:
Edit Rainbow:
Strobe/Timing
Step 1. Select Edit Step or New Step from the Edit User Chase menu.
Step 2. The top left field indicates the preset or color filter to be used for the step. When set to OFF no preset or
color filter is to be used. Use LEFT and RIGHT buttons to scroll through all presets and color filters.
Step 3. Use the Up and Down keys to scroll through the output parameters. Once a parameter is selected, use the
left and right arrow buttons to make adjustments.
If security features are enabled, the Up and Down arrows will have no effect. See “Settings/Security” on page 13.
Fixtures with multiple pixel control include a parameter titled “Pixel” that allows you to independently adjust the output of each individual pixel or the entire fixture.
Depending on the DMX map set assigned the DMX menu, different either RGBW or HSIC parameters will be available.
Step 4. Once all values are adjusted as desired, press the Check Mark button to return to the
Step 5. Continue editing steps as needed. When complete, press the Return to Main Menu
button or up one level (as shown to the right). to exit the Edit User Chase window.
Step 6. The user chase is now saved and can be recalled via the menu or DMX.
Notes:
An additional option in the Edit User Chase options is to have the fixture generate a multi-colored chase using
different pixels from the fixture. When you select Rainbow from the Edit Step window the Edit Rainbow window
will display the following options.
Table 5: Edit Rainbow parameters
Parameter
Direction
Mode
Select either right or left to define the direction the rainbow effect runs.
Select from Mode 1 / Mode 2.
Number of Color Select the number of colors used in the rainbow effect.
Current Color Will display the values of the current color selected. Press the Check Mark button to edit the selected color.
Description
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the settings. When
finished, press the Check button to exit the menu level.
The bottom of the Edit Rainbow window displays a graphical representation of the current
rainbow effect. When finished editing the Rainbow, press the Main Menu button (as shown
to the right). You will be asked to confirm that you wish to save the rainbow. Select Yes to
save and return to the Edit a Chase window.
The Strobe/Timing menu allows you to assign strobe and timing values from the menu system. These settings are instantly applied to any active Preset, Color filter, or Chase.
Use the Up and Down buttons to select parameters and the Left and Right buttons to adjust the currently selectedparameters. The adjustable parameters are described in Table 6 on page 13.
Operation and Programming
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
14
Edit User Chase screen.
Return to Main Menu Button
Return to Main Menu Button
Table 6: Strobe/Timing Parameters
Table 8: PIN Level Parameters
Table 7: Security Lock Levels
ParameterMaster Intensity Overall fixture output intensity level.
Strobe: X Strobe mode and rate value settings following DMX map (see for details).DMX CONTROL
Duration The time each strobe flash remains ON.
RotateMode The way how the fixture will rotate.
Position The exact position for the INDEX from Rotate Mode (0-255)
Description
ParameterEnter Pass PIN Enter a PIN code matching the level codes assigned in the Settings/Security menu to
toggle the current security level.
Level 1 PIN Edit the PIN code used to toggle the Level 1 security.
Edit the PIN code used to toggle the Level 2 security.
Edit the PIN code used to toggle the Level 3 security.
Level 2 PIN
Level 3 PIN
Power-up Level Select the security level to default to when the fixture is powered ON.. Disable PIN will disable all security functions.. Lock will lock all functions.
Description
Lock LevelLevel 1 Edit Presets, Edit Chases, and Settings Menu
Level 2 Settings Menu
Level 3 All
Menu Functions Affected
Settings/Security
All Showline fixtures have a multiple level locking feature. This allows you to configure the fixture and allow
different menu access to multiple users. The menu system can be lock instantly or assigned to power on to a
particular lock level. You can assign three different 4-digit PIN(personal identification number) codes to each
unlock specific levels of functionality within the menu system.
Anytime the fixture is locked, each PIN code will unlock all functions except the pertaining features assigned
via the security level.
Use the Up and Down buttons to select security PIN codes. Press the Check button and then use Left and Right and
Up Down buttons to assign the pin code. Press the Check button to save the new PIN code.
The Power-Up Level parameters assigns a lock level to the fixture when power is applied. use the Up and Down
buttons to select the Power-Up Level, and then use the Left and Right buttons to select the Power-up Level option.
Operation and Programming
Note: The Level 3 PIN will always unlock all functions.
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
15
Settings/General
Settings/Factory Default
Settings/DMX
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the different general
fixture settings. When finished, press the Check button to exit the menu level. The adjustable parameters are
described in Table 9.
Factory default menu settings can be recalled through this menu option. You can select if you wish to overwrite the user edited presets and chases.
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the different settings. When finished, press the Check button to exit the menu level. The adjustable parameters are described in Table 10.
DMX configuration options are available in the DMX menu.
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the fixture’s DMX settings.
When finished, press the Check button to exit the menu level. The adjustable parameters are described in Table 11.
Table 9: General Level Parameters
Table 11: DMX Setting Parameters
ParameterPower-Up
Mode Select either Master/Slave (see for more information).Master / Slave Operational Mode
Select the action of the fixture when the unit is powered ON. You can select from Off, Last Set, Color filters, presets, and chases.
Dim Response
Select Normal or Incandescent dimming response.
Normal: Fixture LEDs dim with a normal response.
Incandescent: Fixture LED’s dim with an incandescent emulation response. The response to dimming commands will be slightly delayed at lower intensities.
Dimming Curve Select one of four dimming curve choices (see for more information).Dimming Curve Selection
Calibration
Fan Control
Toggle Harmonize Color Calibration on or off ( see for more information).Harmonize Color Calibration
Select Auto or Off fan operation (see DMX CONTROL for more information).
Description
ParameterDMX Enable
Address Assigns the fixture’s DMX start address.
Map Select the DMX map for the fixture to use (see DMX CONTROL section for more information).
Off - Turn off all LED output.
Enable - Fixture will respond to DMX commands/signals.
disable - Fixture will ignore DMX commands/signals.
Last Action - restore the last menu action.
Power-up - follow the power-up value in the settings menu.
Hold - continue with the last DMX values received.
When no DMX
Selects the action of the fixture when the unit is powered ON and not receiving DMX
LED Group
Pan/Tilt Setting
Select the number of LED groups to control via DMX (see DMX CONTROL section for more information).
Set the parameters for Pan/Tilt
Description
Table 10: Facotry Default Parameters
Parameter
ProtectedNo - all menu items are able to be restored to factory defaults.
No - no action.
Preset & Chase - user edited Presets and Chases are not able to be restored to factory defaults.
Yes - restored to factory default menu settings.
Load Factory
Description
Operation and Programming
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
16
Settings/ArtNet Settings
Settings / Display
Lock Fixture
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the different general
fixture settings. When finished, press the Check button to exit the menu level. The adjustable parameters are
described in Table 12.
Options of the fixture’s LCD display can be adjusted in the Display menu.
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the fixture’s DMXsettings. When finished, press the Check button to exit the menu level. The adjustable parameters are described in Table 13.
Note: When the fixture is powered off, the Lock fixture function will be disabled. To assign fixture power-up
security refer to (see “ Settings/Security” on page 13 for more information).
You can lock all fixture functions, requiring a PIN code to access the menu functions. When you select this menu
item, you are asked to confirm that you wish to lock the fixture. Once locked, all menu items can only be accessed
by entering one of the three PIN codes assigned in the Settings/Security menu. (see “ Settings/Security” on page 15
for more information). The PIN code used to unlock the fixture will only unlock the functionality assigned to that
particular PIN code.
Table 12: ArtNET Parameters
Table 13: LCD Display Parameters
ParameterFlip Display
Off TimeAssign a time for the display to automatically turn off after the last button press. A value of ON will leave the display on indefinitely.
Language Selected English is the only language supported.
Yes - The display will be inverted.
No - The display will not be inverted.
Auto - The display will automatically invert depending upon fixture orientation.
Description
ParameterIP Address
Net Select a Net number from 0-255
Set the IP address for the fixture.
Sub-Net Select a Sub-Net number from 0-15
Universe Select a Universe number from 0-15.
DMX > ArtNET - DMX will run first priority.
ArtNET > DMX ArtNET - ArtNET will run first priority.Protocol Priority
Description
Operation and Programming
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
17
Password (PassPIN)
Quick Selection Buttons
DMX Address
To edit the DMX start address:
Status
The Password menu item will display an Enter PassPIN dialog box. Use the Up Down Left Right buttons to enter a
PIN code matching the codes assigned in the Settings/Security menu to toggle the current security level.
The Showline menu system includes four quick selection buttons on the top of the menu. These keys provide direct access to common functions and act as shortcut to main menu items as described in Table 14
You can display and edit the current DMX start address for the fixture by
pressing the Quick Select button on the top of the menu system (as shown right).
The current DMX start address will be display in large digits.
Step 1. Press the Check Mark button to begin the DMX start address editing.
The last digit will change to a blue color.
Step 2. use the UP and Down arrows to change the value of the currently
selected digit.
Step 3. Use the Left and Right arrows to select another digit to adjust.
Step 4. Press the Check Mark button to save the new DMX Start Address.
The Status screen displays the current value of the master intensity and each LED of the luminaires. The number of
pixels will vary depending upon fixture type. The Up Down Left Right arrows to scroll through the different
LEDs and view their levels.
The last Status item displayed shows the RDM UID and current Firmware VersionPress the Check Mark button to exit the Status screen.
Table 14: General Level Parameters
Quick select Button
Main Menu
Return to Main Menu / Return Up a Menu Item
Edit a Preset
Effects / Edit a Chase
DMX Start Address
Refer to for more information.Settings/General
Refer to for more information.Recalling or Editing Presets
Refer to for more information.Effects Editing User Chasesand
Refer to for more information.DMX Address
Description
Address
255
DMX Address
Operation and Programming
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
18
4. Harmonize Color Calibration
Harmonize is a proprietary, advanced LED color matching system,
consisting of 3 correction modules: RGB, RGBW and Cool White/Warm
White. Every Showline fixture undergoes rigorous testing to provide you
with consistent control of color and intensity as well as output of the highest
quality.
When enabled either via DMX or the fixture’s menu, the Harmonize technoloy
will ensure that colors match from fixture-to-fixture and pixel-to- pixel.
As the Harmonize system matches Showline products, they will all operate
in the same color space. Use the Harmonize system when perfect color matching
is an essential requirement.
Figure 8: SL BEAM 300 FX LED Luminaire Dimmer Curves
Through the menu, you are able to select one of four dimming curves:
Linear Curve
PL_Curve
S_Curve
Square Curve
Linear Curve
S_Curve
PL_Curve*
Square Curve
DMX Value
DMX Value
Lu
men
Ou
tpu
tL
um
en O
utp
ut
Lu
men
Ou
tpu
tL
um
en O
utp
ut
DMX Value
DMX Value
*PL Curve follows the dimming curve of Philips SeleconPL series LED luminaires.
DIMMING CURVE SELECTION
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
19
R G B
x 0.670 0.225 0.173
y 0.31 0.65 0.069
Master / Slave Operational Mode
6. Master / Slave Operational Mode
The Master / Slave Operational Mode allows one SL BEAM 300 FX LED Luminaire to act as the "Master" unitand all other connected units are controlled by this unit. When a unit is set to "Slave" mode, it will only listen to andfollow any commands sent from a "Master" unit. Only one "Master" unit is allowed in this type of operation.
Figure 9: SL BEAM 300 FX LED Luminaire - Master / Slave Configuration
Master Unit
Slave Unit
Slave Unit
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on page 1. "DMX CONTROL" on page 19. For SL BEAM 300 FX LED Luminaire DMX Mapping, refer to
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next luminaire or DMX512
controlled device)
(from console orcontrol device)
SL BEAM 300 FX LED Luminaires
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
20
68%-100% =DMX 173-225 Reserved for future use37%-67% =DMX 94-172 Index Mode6%-36% =DMX 15-93 Spin Mode0-5% =DMX 0-14 OFF (Action same as Home)
DMX CONTROL
This section contains information for operating the luminaire using DMX control in Simple 8-bit, RGBW 8-bit, RGBW 16-bit, HSIC (Hue, Saturation, Intensity and Color Correction) or Pattern modes. For Menu options and detailed information, see "LCD Display and Menu System” on page 6.
Note: These tables assume a DMX start address of 1. When a different starting address is used, this address becomeschannel 1 function and other functions follow in sequence.
1. SL BEAM 300 FX LED Luminaire DMX Mapping
Simple 8-Bit Mode
Table 15 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LED
Luminaire is in simple 8-bit DMX512 mode (as set by the luminaire’s menu system).
Table 15: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Simple 8 - Bit Mode)
DMX CONTROL
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
21
DMX Channel
Parameter Range DMX Range% Default Description
Pan - High Byte
Tilt - High Byte
Master Intensity
Strobe
Zoom
Rotate Mode
Position/Speed
Control
Red 1-19
Green 1-19
Blue 1-19
White 1-19
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
128
128
0
0
0
0
127
0
0 8 bit control of Red LEDs from 0 to full.
8 bit control of Green LEDs from 0 to full.
8 bit control of Blue LEDs from 0 to full.
8 bit control of White LEDs from 0 to full.
0
0
0
8-bit control of Pan
8-bit control of Tilt
Controls strobe operations as follows:
8-bit control of Intensity of LED settings
1
2
3
4
5
6
7
8
9
10
11
12
Open
Closed
Slow Rand
Med Rand
Fast Rand
Strobe Range
Pulse + Slow Rand
Pulse + Med Rand
Pulse + Fast Rand
Pulse + Range
Pulse - Slow Rand
Pulse - Med Rand
Pulse - Fast Rand
Pulse - Range
DMX 0-2
DMX 1976-197
DMX 194-195
DMX 192-193DMX 134-191
DMX 132-133
DMX 130-131
DMX 128-129
DMX 13-127(fastest)
DMX 11-12
DMX 8-10
DMX 6-7
DMX 3-5
DMX 198-255
Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
Default Setting on ConsoleDIM Response_NormalDIM Response_IncandescentDimming Curve_linear Dimming Curve_SquareDimming Curve_S-CurveDiming Curve_PL-CurveCalibration_OFFCalibration_ONFan_AutoFan_OffReserved(Future Use)
=DMX 0-4
=DMX 85-89=DMX 80-84=DMX 75-79=DMX 70-74=DMX 45-49=DMX 40-44=DMX 35-39=DMX 30-34=DMX 10-14=DMX 5-9
=DMX 90-250
Variable control of zoom from 55 - 5.
Spin Mode: 49%-51% Home
52% - 100%: Spin Speed Clockwise
48% - 0 : Spin Speed Counter Clockwise
Index Mode: 49% - 51% Home 0 Degree
52%-100% Index Clockwise
Home 0 degree to +180 degrees
48% - 0 Spin Index Counter Clockwise
Home 0-180degrees
Simple 8-Bit Group Modes
Simple 8-Bit Group Modes
Table 16 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LEDLuminaire is operated in various Simple 8-bit DMX512 Group Control Modes.
Table 16: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Simple 8-Bit Group Modes)
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
22
1
DMX CHANNEL 19 Group Mode 1 Group Mode
23456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384
Pan
Tilt
Master Intensity
Simple 8 bit mode
Strobe
Zoom
Rotate Mode
Position/Speed
ControlRed_1
Green_1
Blue_1
White_1
Red_2
Green_2
Blue_2
White_2
Red_3
Green_3
Blue_3
White_3
Red_4
Green_4
Blue_4
White_4
Red_5
Green_5
Blue_5
White_5
Red_6
Green_6
Blue_6
White_6
Red_7
Green_7
Blue_7
White_7
Red_8
Green_8
Blue_8
White_8
Red_9
Green_9
Blue_9
White_9
Red_10
Green_10
Blue_10
White_10
Red_11Green_11
Blue_11
White_11
Red_12
Green_12
Blue_12
White_12
Red_13
Green_13
Blue_13
White_13
Red_14
Green_14
Blue_14
White_14
Red_15
Green_15
Blue_15
White_15
Red_16
Green_16
Blue_16
White_16
Red_17
Green_17
Blue_17
White_17
Red_18
Green_18
Blue_18
White_18
Red_19
Green_19
Blue_19
White_19
Pan
Tilt
Master Intensity
Strobe
Zoom
Rotate Mode
Position/Speed
ControlRed_1-19
Green_19
Blue_19
White_19
RGBW 8 - Bit Mode
RGBW 8 - Bit Mode
Table 17 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LED
Luminaire is in RGBW 8-Bit DMX512 mode (as set by the luminaire’s menu system).
Table 17: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 8-Bit Mode)
3
1
4
2
Color Presets
Pan 128
128
0-255
0
0
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
Tilt
Master Intensity
DMX Channel
Parameter Range DMX Range% Default Description
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
23
4
Table 17: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 8-Bit Mode)
RGBW 8 - Bit Mode
DMX Channel
Parameter Range DMX Range% Default Description
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
24
CF_22_Double C.T Blue
CF_25_Full C.T Blue
DMX 113-114
DMX 119-120
4
5
6
Strobe
Duration
Table 17: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 8-Bit Mode)
RGBW 8 - Bit Mode
DMX Channel
Parameter Range DMX Range% Default Description
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
25
Table 17: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 8-Bit Mode)
RGBW 8 - Bit Mode
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
26
DMX Channel
Parameter Range DMX Range% Default Description
8
9
10
11
12
13
14
15
16
7
Rotate Mode
Position/Speed
Focus Timing
Timing
Control
Red1-19
Green1-19
Blue1-19
White1-19
Zoom
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100% 8 bit control of Red LEDs from 0 to full
8 bit control of Green LEDs from 0 to full
8 bit control of Blue LEDs from 0 to full
8 bit control of White LEDs from 0 to full
0-100%
0-100%
0-100%
0-100%
0
0
255
255
0
0
0
0
0
0
68%-100% =DMX 173-225 Reserved for future use
37%-67% =DMX 94-172 Index Mode
6%-36% =DMX 15-93 Spin Mode
0-5% =DMX 0-14 OFF (Action same as Home)
Spin Mode: 49%-51% Home52% - 100%: Spin Speed Clockwise48% - 0 : Spin Speed Counter ClockwiseIndex Mode: 49% - 51% Home 0 Degree52%-100% Index Clockwise Home 0 degree to +180 degrees 48% - 0 Spin Index Counter ClockwiseHome 0-180degrees
Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
Default Setting on Console
DIM Response_Normal
DIM Response_Incandescent
Dimming Curve_linear
Dimming Curve_Square
Dimming Curve_S-Curve
Diming Curve_PL-Curve
Calibration_OFF
Calibration_ON
Fan_Auto
Fan_Off
Reserved(Future Use)
=DMX 0-4
=DMX 85-89
=DMX 80-84
=DMX 75-79
=DMX 70-74
=DMX 45-49
=DMX 40-44
=DMX 35-39
=DMX 30-34
=DMX 10-14
=DMX 5-9
=DMX 90-250
1
DMX CHANNEL 19 Group Mode 1 Group Mode
2345
9
6
10
7
11
8
1213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788
Pan
Tilt
Master Intensity
RGBW 8 bit mode
Color Presets
Strobe
Position/Speed
Duration
Focus Timing
Zoom
Timing
Rotate Mode
Control
Red_1
Green_1
Blue_1
White_1
Red_2
Green_2
Blue_2
White_2
Red_3
Green_3
Blue_3
White_3
Red_4
Green_4
Blue_4
White_4
Red_5
Green_5
Blue_5
White_5
Red_6
Green_6
Blue_6
White_6
Red_7
Green_7
Blue_7
White_7
Red_8
Green_8
Blue_8
White_8
Red_9
Green_9
Blue_9
White_9
Red_10
Green_10
Blue_10
White_10
Red_11Green_11
Blue_11
White_11
Red_12
Green_12
Blue_12
White_12
Red_13
Green_13
Blue_13
White_13
Red_14
Green_14
Blue_14
White_14
Red_15
Green_15
Blue_15
White_15
Red_16
Green_16
Blue_16
White_16
Red_17
Green_17
Blue_17
White_17
Red_18
Green_18
Blue_18
White_18
Red_19
Green_19
Blue_19
White_19
Pan
Tilt
Master Intensity
Color Presets
Strobe
Position/Speed
Duration
Focus Timing
Zoom
Timing
Rotate Mode
Control
Red_1-19
Green_19
Blue_19
White_19
RGBW 8-Bit Group Modes
RGBW 8-Bit Group Modes
Table 18 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LEDLuminaire is operated in various RGBW 8-bit DMX512 Group Control Modes.
Table 18: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 8-Bit Group Modes)
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
27
RGBW 16 - Bit Mode
RGBW 16 - Bit Mode
Table 19 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LED
Luminaire is in RGBW 16-bit DMX512 mode (as set by the luminaire’s menu system).
Table 19: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 16-Bit Mode)
DMX Channel
Parameter Range DMX Range% Default Description
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
28
7 Color Presets
Table 19: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 16-Bit Mode)
RGBW 16-Bit Mode
DMX Channel
Parameter Range DMX Range% Default Description
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
29
CF_22_Double C.T Blue
CF_25_Full C.T Blue
DMX 113-114
DMX 119-120
7
8
9
Color Presets
Strobe
Duration
Table 19: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 16-Bit Mode)
RGBW 16 - Bit Mode
DMX Channel Parameter Range DMX Range% Default Description
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
30
17 Control 0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0
127
0
0
11
12
13
14
15
16
10
Rotate Mode
Zoom
255
255
255
255Focus Timing
Intensity Timing
Table 19: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 16-Bit Mode)
RGBW 16 - Bit Mode
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
31
DMX Channel Parameter Range DMX Range% Default Description
Timing
Position/Speed
68%-100% =DMX 173-225 Reserved for future use
37%-67% =DMX 94-172 Index Mode
6%-36% =DMX 15-93 Spin Mode
0-5% =DMX 0-14 OFF(Action same as Home)
180 - 65535
0 - 65535
0 - 65535
0 - 65535 0 - 100%
0 - 100%
0 - 100%
0 - 100%19
2021
2223
2425
Red 1-19 - High ByteRed 1-19 - Low Byte
Green 1-19 - High ByteGreen 1-19 - Low Byte
Blue 1-19 - High ByteBlue 1-19 - Low Byte
White 1-19 - High ByteWhite 1-19 - Low Byte 0
0
0
0 16 bit control of Red LEDs from 0 to full
16 bit control of Green LEDs from 0 to full
16 bit control of Blue LEDs from 0 to full
16 bit control of White LEDs from 0 to full
Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
Default Setting on Console
DIM Response_Normal
DIM Response_Incandescent
Dimming Curve_linear
Dimming Curve_Square
Dimming Curve_S-Curve
Diming Curve_PL-Curve
Calibration_OFF
Calibration_ON
Fan_Auto
Fan_Off
Reserved(Future Use)
=DMX 0-4
=DMX 85-89
=DMX 80-84
=DMX 75-79
=DMX 70-74
=DMX 45-49
=DMX 40-44
=DMX 35-39
=DMX 30-34
=DMX 10-14
=DMX 5-9
=DMX 90-250
Allows for timing control of intensity. Channel should default to 255 for smoothest actions using console and/or manual fades. - See Timing chart for more details.
Allows for timing control of color. Channel should default to 255 for smoothest actions using console and/or manual fades. - See Timing chart for more details.
Spin Mode: 49%-51% Home
52% - 100%: Spin Speed Clockwise
48% - 0 : Spin Speed Counter Clockwise
Index Mode: 49% - 51% Home 0 Degree
52%-100% Index Clockwise
Home 0 degree to +180 degrees
48% - 0 Spin Index Counter Clockwise
Home 0-180degrees
Allows for timing control of zoom
RGBW 16-Bit Group Modes
RGBW 16-Bit Group Modes
Table 20 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LEDLuminaire is operated in various RGBW 16-bit DMX512 Group Control Modes.
Table 20: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (RGBW 16-Bit Group Modes)
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
32
DMX CHANNEL 19 Group Mode 1 Group Mode
RGBW 8 bit mode
1
2
3
45
6
7
89
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
Pan - High Byte Pan - High Byte
Pan - Low Byte Pan - Low Byte
Tilt - High Byte Tilt - High Byte
Tilt - Low Byte Tilt - Low ByteMaster Intensity - High Master Intensity - High
Master Intensity - Low Master Intensity - Low
Color Presets Color Presets
Strobe Strobe Duration Duration
Zoom Zoom
Rotate Mode Rotate Mode
Position/Speed Position/Speed
Focus Timing Focus Timing
Intensity Timing Intensity Timing
Color Timing Color Timing
Zoom Timing Zoom Timing
Control Control
Red_1 - High Byte Red_1-19 - High Byte
Red_1 - Low Byte Red_1-19 - Low Byte
Green_1 - High Byte Green_1-19 - High Byte
Green_1 - Low Byte Green_1-19 - Low Byte
Blue_1 - High Byte Blue_1-19 - High Byte
Blue_1 - Low Byte Blue_1-19 - Low Byte
White_1 - High Byte White_1-19 - High Byte
White_1 - Low Byte White_1-19 - Low Byte
Red_2 - High Byte
Red_2 - Low Byte
Green_2 - High Byte
Green_2 - Low Byte
Blue_2 - High Byte
Blue_2 - Low Byte
White_2 - High Byte
White_2 - Low Byte
Red_3 - High Byte
Red_3 - Low Byte
Green_3 - High Byte
Green_3 - Low Byte
Blue_3 - High Byte
Blue_3 - Low Byte
White_3 - High Byte
White_3 - Low Byte
Red_4 - High Byte
Red_4 - Low Byte
Green_4 - High Byte
Green_4 - Low Byte
Blue_4 - High Byte
Blue_4 - Low Byte
White_4 - High Byte
White_4 - Low Byte
Red_5 - High Byte
Red_5 - Low Byte
Green_5 - High Byte
Green_5 - Low Byte
Blue_5 - High Byte
Blue_5 - Low Byte
White_5 - High Byte
White_5 - Low Byte
Red_6 - High Byte
Red_6 - Low Byte
Green_6 - High Byte
Green_6 - Low Byte
Blue_6 - High Byte
Blue_6 - Low Byte
White_6 - High Byte
White_6 - Low Byte
Red_7 - High Byte
Red_7 - Low Byte
Green_7 - High Byte
Green_7 - Low Byte
Blue_7 - High Byte
Blue_7 - Low Byte
White_7 - High Byte
White_7 - Low Byte
Red_8 - High Byte
Red_8 - Low Byte
Green_8 - High Byte
Green_8 - Low Byte
Blue_8 - High Byte
Blue_8 - Low Byte
White_8 - High Byte
White_8 - Low Byte
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
Red_9 - High Byte
Red_9 - Low Byte
Green_9 - High ByteGreen_9 - Low Byte
Blue_9 - High Byte
Blue_9 - Low Byte
White_9 - High Byte
White_9 - Low Byte
Red_10 - High Byte
Red_10 - Low Byte
Green_10 - High Byte
Green_10 - Low Byte
Blue_10 - High Byte
Blue_10 - Low Byte
White_10 - High Byte
White_10 - Low Byte
Red_11 - High Byte
Red_11 - Low Byte
Green_11 - High Byte
Green_11 - Low Byte
Blue_11 - High Byte
Blue_11 - Low Byte
White_11 - High Byte
White_11 - Low Byte
Red_12 - High Byte
Red_12 - Low Byte
Green_12 - High Byte
Green_12 - Low Byte
Blue_12 - High Byte
Blue_12 - Low Byte
White_12 - High Byte
White_12 - Low Byte
Red_13 - High Byte
Red_13 - Low Byte
Green_13 - High Byte
Green_13 - Low Byte
Blue_13 - High Byte
Blue_13 - Low Byte
White_13 - High Byte
White_13 - Low Byte
Red_14 - High Byte
Red_14 - Low Byte
Green_14 - High Byte
Green_14 - Low Byte
Blue_14 - High Byte
Blue_14 - Low Byte
White_14 - High Byte
White_14 - Low Byte
Red_15 - High Byte
Red_15 - Low Byte
Green_15 - High Byte
Green_15 - Low Byte
Blue_15 - High Byte
Blue_15 - Low Byte
White_15 - High Byte
White_15 - Low ByteRed_16 - High Byte
Red_16 - Low Byte
Green_16 - High Byte
Green_16 - Low Byte
Blue_16 - High Byte
Blue_16 - Low Byte
White_16 - High Byte
White_16 - Low Byte
Red_17 - High Byte
Red_17 - Low Byte
Green_17 - High Byte
Green_17 - Low Byte
Blue_17 - High Byte
Blue_17 - Low Byte
White_17 - High Byte
White_17 - Low Byte
Red_18 - High Byte
Red_18 - Low Byte
Green_18 - High Byte
Green_18 - Low Byte
Blue_18 - High Byte
Blue_18 - Low Byte
White_18 - High Byte
White_18 - Low Byte
Red_19 - High Byte
Red_19 - Low Byte
Green_19 - High Byte
Green_19 - Low Byte
Blue_19 - High Byte
Blue_19 - Low Byte
White_19 - High Byte
White_19 - Low Byte
HSIC Mode
HSIC Mode
Table 21 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LED Luminaire is in HSIC (Hue, Saturation, Intensity, and Color Correction) DMX512 mode (as set by the luminaire’s menu system).
Table 21: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (HSIC Mode)
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
33
DMX Channel Parameter Range DMX Range% Default Description
16-bit control of Pan
16-bit control of Tilt
8 bit control of Intensity of LED settings
1
3
4
5
6
7
8
9
10
11
12
13
16
17
18
14
15
2
Pan - High Byte
Tilt - High Byte
Tilt - Low Byte
Master Intensity
Strobe
Duration
Zoom
Rotate Mode
Position/Speed
Focus Timing
Timing
Control
Saturation1-19
Intensity1-19
CCT1-19
Hue1-19 - High Byte
Hue1-19 - Low Byte
Pan - Low Byte
0-65535
0-65535
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-65535
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
32768
32768
0
0
0
0
127
255
255
0
0 8 bit control of Saturation
8 bit control of Intensity0
0
0 16 bit control of Hue 0-359°
0
Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
Default Setting on ConsoleDIM Response_NormalDIM Response_Incandescent
Dimming Curve_linear
Dimming Curve_SquareDimming Curve_S-CurveDiming Curve_PL-Curve
Calibration_OFFCalibration_ON
Fan_Auto
Fan_OffReserves(Future Use)
=DMX 0-4
=DMX 85-89
=DMX 80-84
=DMX 75-79=DMX 70-74
=DMX 45-49=DMX 40-44=DMX 35-39
=DMX 30-34
=DMX 10-14=DMX 5-9
=DMX 90-250
Allows for timing control of intensity. Channel should default to 255 for smoothest actions using console and/or manual fades. - See Timing chart for more details.
68%-100% =DMX 173-225 Reserved for future use37%-67% =DMX 94-172 Index Mode6%-36% =DMX 15-93 Spin Mode0-5% =DMX 0-14 OFF (Action same as Home)
Spin Mode: 49%-51% Home
52% - 100%: Spin Speed Clockwise
48% - 0 : Spin Speed Counter Clockwise
Index Mode: 49% - 51% Home 0 Degree
52%-100% Index Clockwise
Home 0 degree to +180 degrees
48% - 0 Spin Index Counter Clockwise
Home 0-180degrees
Timing Control of Pan/Tilt
HSIC Group Modes
HSIC Group Modes
Table 22 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LEDLuminaire is operated in various HSIC DMX512 Group Control Modes.
Table 22: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (HSIC Group Modes)
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
34
1
HSIC MODEDMX CHANNEL 19 Group MODE 1 Group MODE
2345678910111213141516171819202122232425262728
29303132
333435363738394041424344454647484950
51525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108
Pan - High Byte Pan - High BytePan - Low Byte Pan - Low ByteTilt - High Byte Tilt - High ByteTilt - Low Byte Tilt - Low ByteMaster Intensity Master IntensityStrobe StrobeDuration DurationZoom ZoomRotate Mode Rotate ModePosition/Speed Position/SpeedFocus Timing Focus TimingTiming TimingControl ControlHue_1 - High Byte Hue_1-19 - High ByteHue_1 - Low Byte Hue_1-19 - Low ByteSaturation_1 Saturation_1-19Intensity_1 Intensity_1-19CCT_1 CCT_1-19Hue_2 - High ByteHue_2 - Low ByteSaturation_2Intensity_2CCT_2Hue_3 - High ByteHue_3 - Low ByteSaturation_3Intensity_3CCT_3
Hue_4 - High ByteHue_4 - Low ByteSaturation_4Intensity_4
CCT_4
Hue_5 - High ByteHue_5 - Low ByteSaturation_5Intensity_5CCT_5Hue_6 - High ByteHue_6 - Low ByteSaturation_6Intensity_6CCT_6Hue_7 - High Byte
Hue_7 - Low ByteSaturation_7Intensity_7CCT_7Hue_8 - High ByteHue_8 - Low Byte
Saturation_8Intensity_8CCT_8Hue_9 - High ByteHue_9 - Low ByteSaturation_9Intensity_9CCT_9Hue_10 - High ByteHue_10 - Low ByteSaturation_10Intensity_10CCT_10Hue_11 - High ByteHue_11 - Low ByteSaturation_11Intensity_11CCT_11Hue_12 - High ByteHue_12 - Low ByteSaturation_12Intensity_12CCT_12Hue_13 - High Byte
Hue_13 - Low ByteSaturation_13Intensity_13CCT_13Hue_14 - High ByteHue_14 - Low ByteSaturation_14Intensity_14 CCT_14Hue_15 - High ByteHue_15 - Low ByteSaturation_15Intensity_15CCT_15Hue_16 - High ByteHue_16 - Low ByteSaturation_16Intensity_16CCT_16Hue_17 - High ByteHue_17 - Low ByteSaturation_17Intensity_17CCT_17Hue_18 - High ByteHue_18 - Low ByteSaturation_18Intensity_18CCT_18Hue_19 - High ByteHue_19 - Low ByteSaturation_19Intensity_19CCT_19
Pattern Mode
Pattern Mode
Table 23 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LED Luminaire is in Pattern mode (as set by the luminaire’s menu system). For a lists of Pattern effects, refer to the
Table 23: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Pattern Mode)
DMX Channel
Parameter Range DMX Range% Default Description
5
60�-�65535
32768
32768
0 - 65535
0 - 65535
12
Pan - High Byte
Pan - Low Byte
3
4
Tilt - High Byte
Tilt - Low Byte
16 bit control of Pan
16 bit control of Tilt
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
35
appendix.
Pattern Mode
Table 23: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Pattern Mode)
DMX Channel
Parameter Range DMX Range% Default Description
Color Presets7
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
36
CF_22_Double C.T Blue DMX 113-114
CF_25_Full C.T Blue DMX 119-120
Defaults DescriptionRange%Range DMXParameterDMX
Table 23: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Pattern Mode)
Pattern Mode
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
37
8
9
11
14
15
16
17
18
19
20
22
24
26
21
23
25
27
13
12
10
Strobe
Duration
Rotate Mode
Intensity Timing
Color Timing
Zoom Timing
Control
Pattern
Pattern Step
Red1-19 - High Byte
Green1-19 - High Byte
Blue1-19 - High Byte
White1-19 - High Byte
Red1-19 - Low Byte
Green1-19 - Low Byte
Blue1-19 - Low Byte
White1-19 - Low Byte
Focus Timing
Position/Speed
Zoom
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-65535
0-65535
0-65535
0-65535
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0
0
01x85
DMX0DMX 1-3(DMX Value-1)/3+1DMX253-255
Strobe’s duration Range is 0-85
0
255
255
255 Allows for timing control of zoom
0
0 Pattern Select DMX0-5DMX5-255
Pattern disablePattern 1-32
0
0
0
0
0 16 bit control of White LEDs from 0 to full
16 bit control of Blue LEDs from 0 to full
16 bit control of Green LEDs from 0 to full
16 bit control of Red LEDs from 0 to full
Pattern Step DMX0-5DMX6-200DMX201-255
No usedPattern step selectPattern running speed 2s-0
255 Timing control of Pan/Tilt
0
0
=DMX 0-4
=DMX 85-89
=DMX 80-84
=DMX 75-79=DMX 70-74
=DMX 45-49=DMX 40-44=DMX 35-39
=DMX 30-34
=DMX 10-14=DMX 5-9
=DMX 90-250
Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
Default Setting on ConsoleDIM Response_NormalDIM Response_Incandescent
Dimming Curve_linear
Dimming Curve_SquareDimming Curve_S-CurveDiming Curve_PL-Curve
Calibration_OFFCalibration_ON
Fan_Auto
Fan_OffReserved(Future Use)
Allows for timing control of intensity. Channel should default to 255 for smoothest actions using console and/or manual fades. - See Timing chart for more details.
Allows for timing control of color. Channel should default to 255 for smoothest actions using console and/or manual fades. - See Timing chart for more details.
68%-100% =DMX 173-225 Reserved for future use37%-67% =DMX 94-172 Index Mode6%-36% =DMX 15-93 Spin Mode0-5% =DMX 0-14 OFF (Action same as Home)
Spin Mode: 49%-51% Home
52% - 100%: Spin Speed Clockwise
48% - 0 : Spin Speed Counter Clockwise
Index Mode: 49% - 51% Home 0 Degree
52%-100% Index Clockwise
Home 0 degree to +180 degrees
48% - 0 Spin Index Counter Clockwise
Home 0-180degrees
Pattern Group Modes
Table 24 provides DMX channel mapping of all DMX512 control values when the SL BEAM 300 FX LEDLuminaire is operated in various Pattern DMX512 Group Control Modes.
Table 24: SL BEAM 300 FX LED Luminaire DMX Channel Mapping (Pattern Group Modes)
Pattern Group Modes
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
38
1DMX CHANNEL
Pattern Mode
23456789101112131415161718192021222324252627
Pan - High BytePan - Low ByteTilt - High ByteTilt - Low ByteMaster Intensity - HighMaster Intensity - LowColor PresetsStrobe DurationZoomRotate ModePosition / SpeedFocus TimingIntensity TimingColor TimingZoom TimingControlPattern Pattern StepRed_1-19 - High ByteRed_1-19 - Low ByteRed_1-19 - High ByteRed_1-19 - Low ByteRed_1-19 - High ByteRed_1-19 - Low ByteRed_1-19 - High ByteRed_1-19 - Low Byte
x Group Mode
DMX Timing Channel Detail
2. DMX Timing Channel DetailTiming channel control improves the timed moves of certain groups of parameters. The SL BEAM 300 FX LEDLuminaire provides timing channels in 16-bit mode (one for intensity time and one for color time) and one timing channel in 8-bit (color and intensity timing combined). The luminaire uses its timing channel value to calculate asmooth continuous operation for a given time and transition.
Guidelines:
Timing channels support time values from zero to 60 minutes.
To use a timing channel instead of console timing, it is recommended to set the timing channel to the desired value and set cue and/or console cue fade time to zero. A combination of time controls can produce unexpected results.
The default value setting in the profile should be 255 (proportional control) to allow smooth operation when using console timing.
The timing channel data should chan ge as a snap. A zero value will give the fastest operation, however, withoutany smoothing this can appear "steppy" in console timed moves.
Refer to for more information."DMX Timing Channel Detail"
Table 25: SL BEAM 300 FX LED Luminaire Timing Channel Detail
% Value DMX= Seconds(unless noted)
0 0 0 (Full Speed)
1 0.2
2 0.4
1 3 0.6
4 0.8
2 5 1
6 1.2
7 1.4
3 8 1.6
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
39
4
% Value DMX= Seconds(unless noted)
1.89
210
5
6
8
10
12
13
14
15
16
17
18
19
20
21
22
23
11
9
7
2.211
2.412
2.814
2.613
315
4.422
4.221
420
3.819
3.618
3.417
3.216
4.623
6.432
6.231
630
5.829
5.628
5.427
5.226
525
4.824
6.633
8.442
8.241
840
7.839
7.638
7.437
7.236
735
6.834
8.643
10.452
10.251
1050
9.849
9.648
9.447
9.246
945
8.844
10.653
10.854
11.658
11.457
11.256
1155
11.859
Table 25: SL BEAM 300 FX LED Luminaire Timing Channel Detail
DMX Timing Channel Detail
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
40
Table 25: SL BEAM 300 FX LED Luminaire Timing Channel Detail
60 12
6124 12.2
62 12.4
63 12.6
65 13
6425 12.8
6626 13.2
73 14.6
72 14.4
7128 14.2
70 14
6927 13.8
68 13.6
67 13.4
7429 14.8
83 16.6
8232 16.4
81 16.2
80 16
7931 15.8
78 15.6
77 15.4
7630 15.2
75 15
8433 16.8
93 18.6
9236 18.4
91 18.2
90 18
8935 17.8
88 17.6
8734 17.4
86 17.2
85 17
9437 18.6
103 23
10240 22
101 21
100 20
9939 19.8
98 19.6
9738 19.4
96 19.2
95 19
104 24
10541 25
109 29
108 28
10742 27
106 26
11043 30
% Value DMX= Seconds(unless noted)
DMX Timing Channel Detail
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
41
Table 25: SL BEAM 300 FX LED Luminaire Timing Channel Detail
111 31
11244 32
113 33
114 34
116 36
11545 35
11746 37
124 44
123 43
12248 42
121 41
12047 40
119 39
118 38
12549 45
134 54
13352 53
132 52
131 51
13051 50
129 49
12850 48
127 47
126 46
13553 55
144 64
14356 63
142 62
141 61
14055 60
139 59
13854 58
137 57
136 56
14557 65
154 74
15360 73
152 72
151 71
15059 70
149 69
14858 68
147 67
146 66
155 75
15661 76
160 80
159 79
15862 78
157 77
16163 81
% Value DMX= Seconds(unless noted)
DMX Timing Channel Detail
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
42
Table 25: SL BEAM 300 FX LED Luminaire Timing Channel Detail
162
16364
164
165
167
16665
16866
175
174
17368
172
17167
170
169
17669
185
18472
183
182
18171
180
17970
178
177
18673
195
19476
193
192
19175
190
18974
188
187
19677
205
20480
203
202
20179
200
19978
198
197
20681
207
211
210
20982
208
21283
83
82
84
93
92
91
90
89
88
87
86
85
94
103
102
101
100
99
98
97
96
95
104
105
109
108
107
106
110
111
112
113
114
116
115
117
124
123
122
121
120
119
118
125
131
130
129
128
127
126
132
% Value DMX= Seconds(unless noted)
DMX Timing Channel Detail
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
43
Note: DMX values 250 to 255 provide smoothing when using console fade timing. DMX value 255(recommended
default) will provide the smoothest timing.
Table 25: SL BEAM 300 FX Luminaire Timing Channel Detail
134
133
135
144
143
142
141
140
139
138
137
136
145
154
153
152
151
150
149
148
147
146
155
156
160
164
159
163
158
162
157
161
165
5 Minutes
60mS
15 Minutes
80mS
30 Minutes
100mS
140mS
60 Minutes
120mS
160mS
213
21484
215
216
218
21785
21986
226
225
22488
223
22287
221
220
22789
236
23592
234
233
232
231
23090
91
229
228
23793
246
24596
244
243
24295
241
24094
239
238
24797
255*100
254*
253*
252*99
251*
250*98
249
248
(Default)
% Value DMX= Seconds(unless noted)
DMX Timing Channel Detail
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
44
Model ID Manufacturer Model Description Product Category
0x1228
MSB of ESTA LSB of ESTA
Category - Network Management
Category - Status Collection
Category - RDM Information
RDM Parameter IDs Value Comment ImplementedGet Set
Allowed Allowed
1st of 2nd of 3rd of 4th of Unique Seq Unique Seq Unique Seq Unique Seq
UID
Philips Entertain. Lighting Asia SL BEAM 300FX (RGBW) 0x0509
50H 41H
0x0001
0x0020
0x0002
0x0030
0x0011
0x0033
0x0050
0x0051
0x0010
0x0032
0x0003
0x0031
0x0015
DISC_UNIQUE_BRANCH
QUEUED_MESSAGE
DISC_MUTE
STATUS_MESSAGES
DISC_UN_MUTE
STATUS_ID_DESCRIPTION
PROXIED_DEVICES
CLEAR_STATUS_ID
SUPPORTED_PARAMETERS
PARAMETER_DESCRIPTION
COMMS_STATUS
PROXIED_DEVICES_COUNT
SUB_DEVICE_STATUS_REPORT_THRESHOLD
Support required only if supporting Parameters beyond the minimum required set.
Support required for Manufacturer-Specific PIDs exposed in SUPPORTED_PARAMETERS message.
1. SL BEAM 300 FX LED Luminaire RDM Parameter IDs
The following tables outline and describe all the RDM parameters IDs associated with SL BEAM 300 FX LEDLuminaires.
Table 26, “SL BEAM 300 FX LED Luminaire RDM Product Parameters IDs”
Table 27, “SL BEAM 300 FX LED Luminaire RDM UID”
Table 28, “SL BEAM 300 FX LED Luminaire RDM Parameters IDs”
Table 29, “SL BEAM 300 FX LED Luminaire RDM Manufacturer IDs” on page 34
Table 30, “SL BEAM 300 FX LED Luminaire RDM Manufacturer Specific PIDs” on page 34
Table 31, “SL BEAM 300 FX LED Luminaire RDM Manufacturer Specific PIDs for sub device” on page 34
Table 26: SL BEAM 300 FX LED Luminaire RDM Product Parameters IDs
SL BEAM 300 FX RDM Parameters
Table 27: SL BEAM 300 FX LED Luminaire RDM UID
Table 28: SL BEAM 300 FX LED Luminaire RDM Parameters IDs
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
45
RDM PARAMETER IDS
Table 28: SL BEAM 300 FX LED Luminaire RDM Parameters IDs
Category - Product Information
Category - DMX512 Setup
Category - Sensors 0x02xx
Category - Dimmer Settings 0x03xx - FUTURE USE
Category - Power / Lamp Settings 0x04xx
Category - Display Settings 0x05xx
Category - Configuration 0x06xx
Category - Control 0x10xx
RDM Parameter IDs Value Comment ImplementedGet Set
Allowed Allowed
0x0060DEVICE_INFO
0x00C1BOOT_SOFTWARE_VERSION_ID
0x0121SLOT_DESCRIPTION
0x0201SENSOR_VALUE
0x0401
0x0601
0x0404
0x1000
0x0500
0x00C0SOFTWARE_VERSION_LABEL
0x0120SLOT_INFO
0x0200SENSOR_DEFINITION
0x0400
0x0600
0x0403
0x0603
0x00B0LANGUAGE
0x00F0DMX_START_ADDRESS
0x00A0LANGUAGE_CAPABILITIES
0x00E1DMX_PERSONALITY_DESCRIPTION
0x0090FACTORY_DEFAULTS
0x00E0DMX_PERSONALITY
0x0082DEVICE_LABEL
0x0081MANUFACTURER_LABEL
0x0080DEVICE_MODEL_DESCRIPTION
0x0070PRODUCT_DETAIL_ID_LIST
0x00C2BOOT_SOFTWARE_VERSION_LABLE
0x0122DEFAULT_SLOT_VALUE
0x0202RECORD_SENSORS
0x0402
0x0602
0x0405
0x1001RESET_DEVICE
REAL_TIME_CLOCK
PAN_TILT_SWAP
TILT_INVERT
DISPLAY_LEVEL
LAMP_ON_MODE
DEVICE_POWER_CYCLES
PAN_INVERT
DISPLAY_INVERT
LAMP_STATE
LAMP_STRIKES
LAMP_HOURS
DEVICE_HOURS
IDENTIFY_DEVICE
0x0501
Required if device uses a DMX Slot
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
46
RDM PARAMETER IDS
Table 28: SL BEAM 300 FX LED Luminaire RDM Parameters IDs
Table 29: SL BEAM 300 FX LED Luminaire RDM Parameter Status IDs
Table 30: SL BEAM 300 FX LED Luminaire RDM Parameter Specific PIDs
Table 31: SL BEAM 300 FX LED Luminaire RDM Parameter Specific PIDs for sub device
RDM Parameter IDs Value Comment ImplementedGet Allowed Set Allowed
0x1010POWER_STATE
0x1020PERFORM_SELFTEST
0x1030CAPTURE_PRESET
0x1021SELF_TEST_DESCRIPTION
0x1031PRESET_PLAYBACK
Manufacturer Specific messages are in the range of 0x8000 - 0xFFDF. Each Manufacturer-specific Status ID shall have a unique meaning, which shall be consistent across all products having a given Manufacturer ID. See Table B-2, ANSI E1.20-2010
Status ID Message Value Data Value 1 Data Value 2 Status ID Description
8100H 00H 00H ALL OK
Type Length Unit Prefix Min Max Default DescriptionGet Allowed Set Allowed RDM Parameter IDs
1 NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
NONE NONE
100 1008A00H U8 0 DIMMER
1 4 08AA0H U8 0 Backlight Off time
1 3 08A0CH U8 0 DMX FAIL MODE
1 3 08AA1H U8 0 Dimming Curve
1
1
1
1
0
0
8A42H
8AD3H
U8
U8
0
0
Incandescent Effect
PAN/TILT FEEDBACK
1
1
1
1
0
0
8A40H
8A41H
U8
U8
0
0
Link Mode
Lock Fixture
1
1
255
1
255
0
8AC2H
8A44H
U8
U8
0
0
Color Timing
Calibration ON/OFF Setup
1
1
255
94
255
0
8AC0H
8AA2H
U8
U8
0
0
Intensity Timing
Power UP Setup
1 1 08A97H U8 0 Fan AUTO/OFF Setup
1 255 08A93H U8 0 Zoom
1 65535 327688A96H U16 0 Tilt
1 65535 327688A95H U16 0 Pan
1 255 08A94H U8 0 Duration
1 255 08A92H U8 0 Strobe
1 31 08AB1H U8 0 Preset
1 43 08AB0H U8 0 Color Filter
1 18 18AB2H U8 1 Chase
Category - Manufacturer Defined PIDs - Range is 0x80000-0xffdf(See ANSI E1.20-2010 Standard, Table A-3)
Type Length Unit Prefix Min Max Default DescriptionGet Allowed Set Allowed RDM Parameter IDs
1 NONE NONE
NONE NONE
NONE NONE
NONE NONE
100
100
100
100
100
100
100
100
8A04H U8 0 Dimmer Red
18A07H U8 0 Dimmer White
18A06H U8 0 Dimmer Blue
18A05H U8 0 Dimmer Green
Category - Manufacturer Specific PIDs for sub device - Range is 0x80000-0xffdf(See ANSI E1.20-2010 Standard, Table A-3)
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
47
CLEANING AND CARE
Being a solid-state fixture, and unlike most fixtures, the SL BEAM 300 FX LED Luminaire requires very littleroutine maintenance by the user. This section covers portions of the luminaire that can be removed for cleaning.
The SL BEAM 300 FX LED Luminaries requires special care when it comes to cleaning front lens assembly. Additional care needs to be taken with the plastic components because they are much easier to scratch or damage
than glass. The following is a list of cleaning materials required to care for your SL BEAM 300 FX LED Luminaire:
Note: *Reagent grade isopropyl alcohol is good to use on the SL BEAM 300 FX LED Luminaire plastic optics with anti-reflection coatings.
WARNING! Under no circumstances should ammonia-based cleaners, acetone, or other harsh solvents be used on or near the SL BEAM 300 FX LED Luminaire. These types of cleaners or solvents can permanently damage theoptics or housings of the fixture.
If you have any questions regarding the use or care of your SL BEAM 300 FX LED Luminaire, please contactShowline technical support or your local Authorized Dealer.
WARNING! All cleaning should be performed with power completely removed from the luminaire. Never removeprotective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when cleaning the fixture. All service and maintenance, other than described herein, should be performed by a qualified technician or Authorized Service Center.
Lint free lens tissue
Lint or powder free gloves
Reagent grade isopropyl alcohol*
A mild soap solution
If the lens is still dirty after using isopropyl alcohol, for instance if fingerprints or oil is just redistributed and not cleaned off the optic, then a mild soap and water solution can be used to gently wash the lens. Repeat the cleaningwith isopropyl alcohol to eliminate streaks and soap residue.
Step 1. Turn off luminaire and allow to cool completely.
Step 2. Apply a small amount of reagent grade isopropyl alcohol to lint-free lens tissue.
Step 3. Wipe all debris, dirt, fingerprints, etc. from lens.
Step 4. Using a second lint-free lens tissue, wipe off any alcohol residue.
For all other service and maintenance issues, please contact your local Showline office or an Authorized Service Center.
1. Special Cleaning and Care Insturctions
2. Front Lens Cleaning
3. Service and Maintenance
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
48
Technical Specifications
TECHNICAL SPECIFICATIONS
1. Operational Specifications
19 Osram 4-in-1 RGBW LED Array
100V to 240V(+/- 10%, auto-ranging)2700 - 6500K (user adjustable)
Source:
540 degrees (end to end less than 2.5s)
CE / C-Tick marked and ETL listed
Pan:
Compliance:
Die Cast aluminium with Powder CoatingHousing:14.5kg (31.9 lbs) - Luminaire only (no mount, AC input cable or accessories)Weight:Forced Air CoolingCooling:5%-95% Non condensingHumidity:-20 to 40 Degrees C ( -4 to 104 Degrees F)Ambient Temperature:DMX512(1990) / DMX512A (RDM) / On-Board MenuControl Protocols:50/60HzFrequency:
360 Watts(max).Power Consumption:Input Voltage:Color Temerature:
4500 lumensLight Output:5-55 Degrees(4-40 degrees at 50% of max illumination) Zoom Range:
230 degrees (end to end less than 1.5s)
IP20
Tilt:
IP Rating:
Note: Common model specifications shown. For specific model specifications, features, and accessories, refer to the product specification sheet for more details.
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
49
Luminaire Dimensions
2. Luminaire Dimensions
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
50
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
51NOTE
NOTE
Pattern Details
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
52
Appendix
All patterns can be selected via external DMX/RDM console by their corresponding DMX value on Channel 18 and 19.
DMX Channel 18 will select the pattern group and DMX Channel 19 will select an individual pattern. The combination
of DMX channel 18 and 19 will locate the desired pattern precisely. Details are as below.
Channel 18
Channel 18
Channel 18
Channel 18
5-12 29-36
29-36
29-36
29-36
29-36
29-36
29-36
29-36
29-36
29-36
21-28
21-28
21-28
21-28
21-28
21-28
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
13-20
5-12 165-180 135-147
174
5-12 149-164 176122-134
161-173
5-12 133-148 157-175109-121
5-12 117-132 138-15696-108
5-12 101-116 119-13783-95
5-12 85-100 100-11816570-82
5-12 69-84 81-99133-16457-69
5-12 53-68 62-80101-13244-56
5-12 37-52 43-6169-10031-43
5-12 21-36 24-4236-6818-30
5-12 181 148-160
5-20 5-235-365-17
Channel 19
Channel 19
Channel 19
Channel 19
Pattern PatternPatternPattern
Orientation: Patterns are shown when looking at the front of a standing fixture; Head faced in direction of fixtures front label:DMX Pan @75, Tilt @230.
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
53
Channel 18
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
37-44
125-136
161-172
185
113-124
149-160
173-184
101-112
89-100
77-88
65-76
53-64
41-52
29-40
17-28
137-148
5-16
Channel 19
Pattern Channel 18
Channel 18
Channel 18
45-52
45-52
45-52
45-52
45-52
45-52
45-52
45-52 53-60
53-60
53-60
53-60
53-60
53-60
53-60
53-60
53-60
53-60
61-68
61-68
61-68
61-68
61-68
61-68
61-68
61-68
61-68
61-68176 176
157-175 157-175
173 138-156 138-156
149-172 119-137 119-137
125-148 100-118 100-118
101-124 81-99 81-99
77-100 62-80 62-80
53-76 43-61 43-61
29-52 24-42 24-42
5-28 5-23 5-23
Channel 19
Channel 19
Channel 19
Pattern Pattern Pattern
Pattern Details
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
54
Channel 18
77-84
77-84
77-84
77-84
77-84
77-84
77-84 167
140-166
113-139
86-112
59-85
32-58
5-31
Channel 19
Pattern
Channel 18
85-92
85-92
85-92
85-92
85-92
85-92
85-92
85-92
85-92
85-92
85-92
85-92
165-180
149-164
133-148
117-132
101-116
85-100
69-84
53-68
37-52
21-36
181
5-20
Channel 19
Pattern
Channel 18
93-100
93-100
93-100
93-100
93-100 161
122-160
83-121
44-82
5-43
Channel 19
Pattern
Channel 18
69-76
69-76
69-76
69-76
69-76
69-76
69-76
69-76 173
149-172
125-148
101-124
77-100
53-76
29-52
5-28
Channel 19
Pattern Channel 18
101-108
101-108
101-108
101-108
101-108
101-108
101-108
101-108
101-108
101-108 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern
Pattern Details
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
55
Channel 18
109-116
109-116
109-116
109-116
109-116
109-116
109-116
109-116
109-116
109-116
109-116
109-116
165-180
149-164
133-148
117-132
101-116
85-100
69-84
53-68
37-52
21-36
181
5-20
Channel 19
Pattern Channel 18
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
117-124
125-136
173-184
113-124
161-172
101-112
149-160
89-100
77-88
65-76
53-64
41-52
29-40
17-28
137-148
185
5-16
Channel 19
Pattern Channel 18
125-132
125-132
125-132
125-132
125-132
125-132
125-132
125-132
125-132 173
152-172
131-151
110-130
89-109
68-88
47-67
26-46
5-25
Channel 19
Pattern Channel 18
133-140
133-140
133-140
133-140
133-140
133-140
133-140
133-140
133-140
133-140 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern
Pattern Details
Channel 18
141-148
141-148
141-148
141-148
141-148
141-148
141-148
141-148 173
149-172
125-148
101-124
77-100
53-76
29-52
5-28
Channel 19
Pattern Channel 18
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
149-156
105-114
165-174
95-104
155-164
85-94
145-154
75-84
135-144
65-74
125-134
55-64
45-54
35-44
25-34
15-24
115-124
175
5-14
Channel 19
Pattern Channel 18
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
157-164
105-114
165-174
95-104
155-164
85-94
145-154
75-84
135-144
65-74
125-134
55-64
45-54
35-44
25-34
15-24
115-124
175-184
185
5-14
Channel 19
Pattern Channel 18
165-172
165-172
165-172
165-172
165-172
165-172
165-172
165-172
165-172 173
152-172
131-151
110-130
89-109
68-88
47-67
26-46
5-25
Channel 19
Pattern
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
58 Pattern Details
Channel 18
173-180
173-180
173-180
173-180
173-180
173-180
173-180
173-180
173-180 173
152-172
131-151
110-130
89-109
68-88
47-67
26-46
5-25
Channel 19
Pattern Channel 18
181-188
181-188
181-188
181-188
181-188
181-188
181-188
181-188 173
149-172
125-148
101-124
77-100
53-76
29-52
5-28
Channel 19
Pattern Channel 18
189-196
189-196
189-196
189-196
189-196
189-196
189-196
189-196
189-196
189-196 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern Channel 18
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
197-204
105-114
165-174
95-104
155-164
85-94
145-154
75-84
135-144
65-74
125-134
55-64
45-54
35-44
25-34
15-24
115-124
175
5-14
Channel 19
Pattern
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
57Pattern Details
Channel 18
205-212
205-212
205-212
205-212
205-212
205-212
205-212
205-212
205-212 173
152-172
131-151
110-130
89-109
68-88
47-67
26-46
5-25
Channel 19
Pattern Channel 18
213-220
213-220
213-220
213-220
213-220
213-220
213-220
213-220
213-220
213-220
213-220
158-174
175
141-157
124-140
107-123
90-106
73-89
56-72
39-55
22-38
5-21
Channel 19
Pattern Channel 18
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
75-81
117-123
68-74
110-116
61-67
103-109
54-60
96-102
47-53
89-95
40-46
33-39
26-32
19-25
12-18
82-88
124-130
5-11
Channel 19
Pattern
221-228
221-228
221-228
221-228
221-228
221-228
221-228
221-228
Channel 18
180
173-179
166-172
159-165
152-158
145-151
138-144
131-137
Channel 19
Pattern
Installation & User’s Manual SL BEAM 300 FX LED Luminaires
58 Pattern Details
Channel 18
229-236
229-236
229-236
229-236
229-236
229-236
229-236
229-236
229-236
229-236 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern Channel 18
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
237-244
135-147
174
122-134
161-173
109-121
96-108
83-95
70-82
57-69
44-56
31-43
18-30
148-160
5-17
Channel 19
Pattern Channel 18
245-252
245-252
245-252
245-252
245-252
245-252
245-252
245-252
245-252
245-252 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern Channel 18
253
253
253
253
253
253
253
253
253
253 176
157-175
138-156
119-137
100-118
81-99
62-80
43-61
24-42
5-23
Channel 19
Pattern
Installation & User’s ManualSL BEAM 300 FX LED Luminaires
59Pattern Details
Dallas
10911 Petal Street
Dalls, TX 75238
Tel: +1 214-647-7880
Fax: +1214-647-8031
Asia
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road
Kwai Chung, N.T., Hong Kong
Tel: +852 2796 9786
Fax: +852 2798 6545
Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: +64 9 481 0100
Fax: +64 9 481 0101
Europe
Rondweg zuid 85
Winterswijk 7012 JD
The Netherlands
Tel: +31 (0) 543-542516
2015 Philips GroupC