Instruction Manual Model 2010

Sewconsult.com 2002 Div. Sewing Educational Warehouse

Table of Contents

Parts of your machine page 4-5 Winding a bobbin page 6-7 Changing a bobbin page 8 Threading page 10-13 Stitch selection page 14 Top tension page 15 Over riding stitches page 16-19 Width page 20 Balance page 21 Blind hems page 22 Buttonholes page 23-27 Care of your machine page 28-29 Troubleshooting guide page 30-33

1

1

User

Text Box

6

User

Text Box

7

3

User

Text Box

9

4

4

User

Text Box

12

5

6

6

7

User

Text Box

17

User

Text Box

18

User

Text Box

19

9

9

10

10

11

11

User

Text Box

26

User

Text Box

27

13

13

30

SINGER FUTURA TROUBLESHOOTING GUIDE

In most cases poor sewing results and breakdowns are caused by three main factors: 1. The condition of the needle. 2. Threading and the quality of thread being used. 3. Mechanical breakdown or damaged parts. The condition of the needle is the most common problem. Bent or damaged needles will cause many different sewing problems. The way the needle is inserted into the needle clamp is also very important.

On most machines you install the needle so the flat is to the back of the machine. Side load machines (bobbin case is inserted on the left side of the machine) the flat is to the right. On some older Singer machines the flat is to the left. The needle should be inserted flat to the back on your machine. Thread quality and the type of thread being used can be a problem. Always use good quality thread and try to avoid thread that is old or knotted. When ever possible use the same thread in the top and bobbin tensions. Thread the machine as shown in your manual and make sure the thread is between the tension discs. If you start with a new needle (inserted properly) and the machine is threaded as per instructions, sewing problems may be mechanical breakdown or damaged parts.

31

For best results your machine should be serviced before every large project. This will increase the life of your machine and give you problem free results when sewing. Here is a checklist we have put together for your type of machine. If you have problems while you are sewing run through the list to correct the problem. POOR STITCH QUALITY 1. The needle is incorrectly inserted. Check that the flat of the needle

is to the back of your machine. 2. The needle is blunt or bent. Your needle should be changed

before each large project or if it hits the needle plate or hook. A damaged needle can also snag most fabrics.

3. The tension is not correct. In most cases the top tension is set to a medium number for regular sewing. Make sure the thread is between the tension discs. Make sure the pressure foot is up when threading your machine. (this will release the tension discs) Check for lint or thread caught in the discs.

4. Type of thread being used can cause problems. Always use good

quality thread. When using heavy thread in the top you will have to use a larger needle. The groove in the needle must fit the thread.

UPPER THREAD BREAKS 1. Check that the needle is inserted correctly and not damaged.

Check size of needle for thread. 2. Check your threading. There should be free movement of the

thread from spool to needle. 3. Make sure the top tension is not too tight.

32

4. Check the needle plate for damage.

5. Check the hook for damage.

LOWER THREAD BREAKS 1. Make sure the bobbin is inserted correctly and the right bobbin for

your machine is being used. 2. Check that the thread is in the bobbin tension and the tension is

not too tight. Also check for thread or lint caught in the tension spring.

3. Make sure the bobbin is evenly wound. Bobbins not wound evenly

in your machine could be a damaged bobbin or damaged hook. 4. Check the needle plate for damage. BOBBIN THREAD NOT BEING BROUGHT UP 1. Check that the needle is inserted correctly. 2. Check threading of the machine. If the take-up lever is not

threaded properly the thread will not come up.

33

3. Hook timing may be out. The hook must pick up the thread from

the scarf of the needle.

STITCH LENGTH VARIES OR WILL NOT FEED 1. Check that your feed dogs are coming up above the needle plate. 2. Check the pressure foot pressure. There must be some pressure

on the foot to feed the fabric. Set the pressure to normal for most types of fabric.

3. Check for lint caught in the feed dogs. 4. Is the pressure foot tight on the pressure bar? Make sure the foot

is pushed up all the way and tight. 5. If all points check out the feed timing may be off. SKIPPING STITCHES 1. Check your threading. 2. Check for needle damage or type of needle being used. 3. Check your hook/needle timing.

34

Notes

Tune-up Guide Model 2000 2001 2005 2010

Sewconsult.com 2002 Div. Sewing Educational Warehouse

Table of Contents

Removing covers and lubrication page 1 – 3 Hook timing page 4 Feed timing page 5 Tensions page 6 Troubleshooting guide page 7 – 10

1

Tuning up your machine There are three main points to a tune-up on a sewing machine. -Cleaning and oiling -Hook and feed timing -Internal tension adjustment Start by removing the covers on your machine.

DO NOT START ANY REPAIRS WITH OUT UNPLUGGING THE MACHINE FROM THE WALL OUTLET

Removing Covers and Lubrication

Loosen the screw on the back of the needle bar cover 2 – 3 turns. Remove the screw behind the foot lifter. Now you can remove the needle bar cover and clean all lint from the area.

2

Oil all parts in the needle bar area including the needle bar and pressure bar. Be very careful not to use too much oil in this area as the oil will find its way onto your fabric. Clean off any excess with a soft cloth.

To remove the slide plate, push down on the spring and pull the plate off. To replace the plate, push the plate on while pushing down on the spring. To get at the spring the base must be removed first.

To remove the bobbin case, loosen the set screw on the front of the machine (shown in the picture above) and remove the nut from the clearance bracket. Lift out the bracket and remove the bobbin case. Clean all lint and replace the bobbin case and bracket. Do not push the clearance pin down further than the nut.

3

Removing Covers and Lubrication Continued

Remove the screws from the base as shown and pull of the bottom cover. Remove all lint from the bottom and the gears. Oil all moving parts and grease the gears with light sewing machine gear grease.

Push the top cover to the right to remove. Model 2005 and 2010 have a screw by the hand wheel on the top cover to remove first. Be sure to have the machine unplugged because the main circuit board is under the top cover.

Oil the top shaft at the points shown. Do not get oil on the wires.

4

Hook Timing

Your machine has timing marks on the needle bar to check the timing. With the needle in the lowest position the upper timing mark must line up with the pressure bar bushing as shown above. Then slowly turn the hand wheel towards you until the lower (bottom) timing mark lines up. At this point the tip of the hook should pass the back of the needle above the eye. If the hook and needle do line up adjust as follows:

Loosen the two screws on the timing belt pulley. Move the hook to line up the tip with the needle as shown. Tighten the screws and recheck the timing.

5

Feed Timing

When the hook timing is set and the lower timing mark is lined up with the pressure bar bushing, the feed timing marks should line up also.

If these marks do not line up, loosen the two screws on the feed eccentric. Move the eccentric until the marks line up. Tighten the screws and recheck the feed timing.

The feed dogs must be down below the plate when the needle is down. If not, move the feed timing 180°.

6

Tensions

From the open top of the machine, locate the top tension unit. The normal top tension for your machine should be 3 – 4 on the tension dial. The bobbin tension should not require adjusting. Stitch out a test seam. The knot should meet in the center of the fabric.

If adjustment is required, loosen the nut on the tension unit and turn the adjusting screw ½ turn at a time and test stitch again. Continue until the right tension is achieved. Make sure the dial is set at normal after you turn the screw and before you test stitch.

Turning the adjusting screw clockwise will tighten the top tension (increase). Retighten the nut and replace the covers on the machine.

7

SINGER FUTURA TROUBLESHOOTING GUIDE

In most cases poor sewing results and breakdowns are caused by three main factors:

1. The condition of the needle. 2. Threading and the quality of thread being used. 3. Mechanical breakdown or damaged parts. The condition of the needle is the most common problem. Bent or damaged needles will cause many different sewing problems. The way the needle is inserted into the needle clamp is also very important.

On most machines you install the needle so the flat is to the back of the machine. Side load machines (bobbin case is inserted on the left side of the machine) the flat is to the right. On some older Singer machines the flat is to the left. The needle should be inserted flat to the back on your machine. Thread quality and the type of thread being used can be a problem. Always use good quality thread and try to avoid thread that is old or knotted. When ever possible use the same thread in the top and bobbin tensions. Thread the machine as shown in your manual and make sure the thread is between the tension discs. If you start with a new needle (inserted properly) and the machine is threaded as per instructions, sewing problems may be mechanical breakdown or damaged parts.

8

For best results your machine should be serviced before every large project. This will increase the life of your machine and give you problem free results when sewing. Here is a checklist we have put together for your type of machine. If you have problems while you are sewing run through the list to correct the problem. POOR STITCH QUALITY 1. The needle is incorrectly inserted. Check that the flat of the needle

is to the back of your machine. 2. The needle is blunt or bent. Your needle should be changed

before each large project or if it hits the needle plate or hook. A damaged needle can also snag most fabrics.

3. The tension is not correct. In most cases the top tension is set to a medium number for regular sewing. Make sure the thread is between the tension discs. Make sure the pressure foot is up when threading your machine. (this will release the tension discs) Check for lint or thread caught in the discs.

4. Type of thread being used can cause problems. Always use good

quality thread. When using heavy thread in the top you will have to use a larger needle. The groove in the needle must fit the thread.

UPPER THREAD BREAKS 1. Check that the needle is inserted correctly and not damaged.

Check size of needle for thread. 2. Check your threading. There should be free movement of the

thread from spool to needle. 3. Make sure the top tension is not too tight. 4. Check the needle plate for damage.

9

5. Check the hook for damage.

LOWER THREAD BREAKS 1. Make sure the bobbin is inserted correctly and the right bobbin for

your machine is being used. 2. Check that the thread is in the bobbin tension and the tension is

not too tight. Also check for thread or lint caught in the tension spring.

3. Make sure the bobbin is evenly wound. Bobbins not wound evenly

in your machine could be a damaged bobbin or damaged hook. 4. Check the needle plate for damage. BOBBIN THREAD NOT BEING BROUGHT UP 1. Check that the needle is inserted correctly. 2. Check threading of the machine. If the take-up lever is not

threaded properly the thread will not come up.

10

3. Hook timing may be out. The hook must pick up the thread from

the scarf of the needle.

STITCH LENGTH VARIES OR WILL NOT FEED 1. Check that your feed dogs are coming up above the needle plate. 2. Check the pressure foot pressure. There must be some pressure

on the foot to feed the fabric. Set the pressure to normal for most types of fabric.

3. Check for lint caught in the feed dogs. 4. Is the pressure foot tight on the pressure bar? Make sure the foot

is pushed up all the way and tight. 5. If all points check out the feed timing may be off. SKIPPING STITCHES 1. Check your threading. 2. Check for needle damage or type of needle being used. 3. Check your hook/needle timing.

11

Notes