SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A”...
-
Upload
phungkhanh -
Category
Documents
-
view
232 -
download
1
Transcript of SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A”...
![Page 1: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/1.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 Plus
Application
Instructions
![Page 2: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/2.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 Plus
Two-component, polymer-modified,
portland cement based.
Fast-setting, trowel-grade mortar.
High performance repair mortar for
horizontal and vertical surfaces (with
forms).
Offers the additional benefit of FerroGard
901- A penetrating corrosion inhibitor.
![Page 3: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/3.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 Plus
Where to use:
• On, above, and below grade on concrete and mortar.
• On horizontal surfaces.
• As a structural repair material for: – Parking structures.
– Industrial plants.
– To level concrete surfaces.
– Walkways, bridges, tunnels, dams, ramps, etc.
![Page 4: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/4.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 Plus
Packaging:
• “A” Comp: 1 gal Jug of
Dispersion.
• “B” Comp: 61.5 lb
Multi-wall bag.
Coverage:
• .51 cu. ft / unit mortor.
• .864 cu. inches per
unit.
![Page 5: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/5.jpg)
Co
nstr
ucti
on
Sika Corporation
Surface Preparation
Cementitious Substrates: • Should be clean and sound.
• Remove contaminants and bond
inhibiting materials from repaired
area.
• Obtain exposed/fractured aggregate
surface ~1/16 to 1/8 inch profile
(ICRI CSP 5 & above).
• Substrate must be saturated surface
dry (SSD) with no standing water.
![Page 6: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/6.jpg)
Co
nstr
ucti
on
Sika Corporation
Surface Preparation
Cementitious Substrates:
• Surface should be
cleaned and
roughened to
create a profile.
![Page 7: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/7.jpg)
Co
nstr
ucti
on
Sika Corporation
Surface Preparation
Saw cut around perimeter of repair area to achieve a minimum 3/8” shoulder.
Eliminates feathered edges giving a clean repair transition
![Page 8: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/8.jpg)
Co
nstr
ucti
on
Sika Corporation
Surface Preparation
Steel: • Remove all corrosion and
contaminants from exposed steel.
• Surface should be cleaned thoroughly by blast cleaning or mechanical means.
• Exposed steel should be cleaned to white steel.
• If half of the diameter is exposed, chip behind bar ½” minimum for mortar only.
![Page 9: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/9.jpg)
Co
nstr
ucti
on
Sika Corporation
Steel Preparation
Steel should be cleaned to a bright
metal finish.
![Page 10: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/10.jpg)
Co
nstr
ucti
on
Sika Corporation
Tools Required
½” Drill Motor.
Low speed drill 400-600 rpm.
Large mixing paddle
Margin trowel
![Page 11: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/11.jpg)
Co
nstr
ucti
on
Sika Corporation
Mixing
Pour approximately
7/8 “A” Component
into clean pail.
Leave approximately
1” of “A” Component
in jug.
![Page 12: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/12.jpg)
Co
nstr
ucti
on
Sika Corporation
Mixing
Add “B” Component
to pail with “A”
already inside, while
mixing continuously.
![Page 13: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/13.jpg)
Co
nstr
ucti
on
Sika Corporation
Mixing
1. Dispersion ¾ -1 gallon of
dispersion/Bag.
2. Start with adding liquid to
the mixing container.
3. Slowly add powder.
4. Once all the powder is
added mix for 3 minutes.
5. Do not add any more than
the recommended liquid.
![Page 14: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/14.jpg)
Co
nstr
ucti
on
Sika Corporation
1. While mixing for 3
minutes stop to scrape
after 1.5 minutes down the
sides to insure all material
is fully mixed.
2. Add additional “A”Comp.
liquid for desired
consistency.
3. Most cases you will have liquid left.
4. Thorough mixing and proper proportioning is
necessary.
Mixing
![Page 15: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/15.jpg)
Co
nstr
ucti
on
Sika Corporation
Apply the mortar to
the patch area while
the Armatec 110
EpoCem is still wet.
If Armatec is not used
as a bonding agent,
SSD the surface and scrub coat the repair mortar
into the substrate filling all pores and voids.
ST 122 PLUS Application
![Page 16: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/16.jpg)
Co
nstr
ucti
on
Sika Corporation
ST 122 PLUS Application
Apply SikaTop
repair mortar to
patch.
Press mortar
behind rebar and
make sure the
material is
consolidated and
compacted fully.
![Page 17: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/17.jpg)
Co
nstr
ucti
on
Sika Corporation
ST 122 PLUS Application
Complete filling
patch area.
Work mortar from
the center of the
patch to the
outside.
![Page 18: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/18.jpg)
Co
nstr
ucti
on
Sika Corporation
Min / Max application thickness
Neat
• Min 1/8 inch
• Max 1.0 inch
Extended
• Min 1.0 inch
• Max 4.0 inch
![Page 19: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/19.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 PLUS Finish
After filling patch section, allow
mortar to set to desired stiffness.
Then finish with steel, wood, or
sponge float to attain a smooth
surface, or broom or burlap-drag for
a rough finish.
![Page 20: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/20.jpg)
Co
nstr
ucti
on
Sika Corporation
Sikatop 122 PLUS Finish
To assist in the
finishing of the
SikaTop use
SikaFilm.
• SikaFilm is a
finishing aid that
also retards
moisture
evaporation.
![Page 21: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/21.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 PLUS Finish
You can use a
steel trowel to
attain a smooth
surface.
![Page 22: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/22.jpg)
Co
nstr
ucti
on
Sika Corporation
Sponge Float Finish
You can use
Sponge float to
attain a textured
surface.
![Page 23: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/23.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop Curing
Cure as per ACI recommendations.
Curing is required.
Moist cure with wet burlap
and polyethylene, a fine
mist of water or water based
curing compound.
Moist curing should
commence immediately after finishing.
Protect newly applied material from
direct sun light, wind, rain and frost.
![Page 24: SikaTop 122 Plus Application Instructions Sika Corporation SikaTop 122 Plus Packaging: •“A” Comp: 1 gal Jug of Dispersion. •“B” Comp: 61.5 lb Multi-wall bag. Coverage:](https://reader031.fdocuments.net/reader031/viewer/2022021504/5aa64ebf7f8b9ae7438e9e80/html5/thumbnails/24.jpg)
Co
nstr
ucti
on
Sika Corporation
SikaTop 122 Plus
Sika Product Data Sheets can be
obtained via:
www.sikaconstruction.com
Refer to data sheets for specific
information on each Sika product.