Sign Post Hardware Section - dynabrackets.com · By far the most widely used style of sign brackets...

www.dynabrackets.com Page 3 [email protected]

Sign & Post Hardware Section (catalogue pages 4‐33)

Sign & Post Hardware section contains: Sign Brackets Booklet Stainless Steel Strapping, Buckles & Tools Booklet Sign Post Accessories Booklet

Issue 23


HS-1 and HS-4 Center Mount Sign Bracket This patented bracket design is perfect for single or back-to-back sign mounting on round posts. This design also allows for easy installation with only one typical 9/16” wrench. The HS series sign bracket is reusable and 360° adjustable to mount signs in any direction. Our design does not require any labour-intensive drilling into sign posts which eliminates damage to city property. These brackets are manufactured from extruded aluminum, which is extremely strong yet flexible enough to increase clamping pressure for a more safe and secure installation.

HS-1 Installation Specifications:

For Center-Mounting Signs

Part No: Fasteners Included:

HS-1 (U) None

HS-1-ZP Zinc Plated Nuts and Bolts

HS-1-SS Stainless Steel Nuts and Bolts

Pre-assembled as shown for convenience Additional 3/8” nuts and bolts are available for back-to-back sign mounting Vandal resistant nuts are available to reduce theft and vandalism

• Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting • Clamps To 2-3/8” Round Posts

HS-4 Installation Specifications:

For Center-Mounting Signs • Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting • Clamps to 4” Round Posts


HS-4 (U) None

HS-4-ZP Zinc Plated Nuts and Bolts

Pre-assembled as shown for convenience Additional 3/8” nuts and bolts are available for back-to-back sign mounting Vandal resistant nuts are available to reduce theft and vandalism

HS-4-SS Stainless Steel Nuts and Bolts


Z238-4.5R1.00 Center Mount Sign Bracket This interlocking sign bracket is used to center mount signs onto 2 3/8” round posts. It features a built-in 4.5” sign support and ribs incorporated into the design for increased clamping pressure to prevent the sign from spinning. A back-to-back attachment is also available. This sign bracket is reusable and 360° adjustable to mount signs in any direction. Our design does not require any labour-intensive drilling into sign posts which eliminates damage to city property. These brackets are manufactured from extruded aluminum, which is extremely strong yet flexible enough to increase clamping pressure for a more safe and secure installation.

Z238-4.5R1.00 Installation Specifications:



Z238-4.5R1.00 (U) None

Z238-4.5R1.00 (ZP) Zinc Plated Nuts and Bolts

Z238-4.5R1.00 (SS) Stainless Steel Nuts and Bolts

Built-in 4.5” backing for extra sign support Z238-4.5BB1.00 bracket is available for back-to-back sign mounting Vandal resistant nuts and bolts are available to reduce theft and vandalism

• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting • Clamps To 2-3/8” Round Posts

Z238-4.5BB1.00 Installation Specifications:

For Back-to-Back Sign Mounting


Z238-4.5BB1.00 (U) None

Z238-4.5BB1.00 (ZP) Zinc Plated Nuts and Bolts

Z238-4.5BB1.00 (SS) Stainless Steel Nuts and Bolts

Built-in 4.5” backing for extra sign support Works with Z238-4.5R1.00 series brackets Vandal resistant nuts are available to reduce theft and vandalism

• Sign-to-Bracket Installation • 5/16” Bolt Thru Sign Mounting • Bolts to Z238-4.5R1.00


BB-12 Installation Specifications:


Fits Up To 3/4” Wide Band


BB-12 (U) None

BB-12 (ZP) Zinc Plated Nuts and Bolts

BB-12 (SS) Stainless Steel Nuts and Bolts

12” sign support backing Vandal resistant nuts and bolts are available to reduce theft and vandalism

• Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting: - 10” Center to Center • Straps To 1-1/2”+ Round, 1-1/2”+ Square, All Lamp Posts

SB-008 Installation Specifications:


Fits Up To 3/4” Wide Band


SB-008 (U) None

SB-008 (SS) Stainless Steel Bolts and Washers and Nylon Washers

Holes of bracket are threaded so there is no need for nuts Vandal resistant bolts are available to reduce theft and vandalism

• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting • Straps To 4”+ Round, 2-1/2”+ Square, All Lamp Posts

FB-021 D021 Installation Specifications:

For Center-Mounting Signs • Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting • Straps To 4”+ Round, 2-1/2”+ Square, All Lamp Posts Dyna Brand

Fits Up To 3/4” Wide Band Band-It Brand Fits Up To 3/4” Wide Band

Part No: Part No: Fasteners Included:

FB-021 (U) - None

FB-021 (SS) D021 Stainless Steel Bolts and Washers and Nylon Washers

Center hole of bracket is threaded so there is no need for a nut Vandal resistant bolts are available to reduce theft and vandalism

SB-001 D001 Installation Specifications:

For Center-Mounting Signs • Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting • Straps To 2-4” Round, 2”+ Square, All Lamp Posts Dyna Brand

Fits Up To 3/4” Wide Band Band-It Brand Fits Up To 3/4” Wide Band


SB-001 (U) - None

SB-001 (SS) D001 Stainless Steel Bolts and Washers and Nylon Washers

Center hole of bracket is threaded so there is no need for a nut Vandal resistant bolts are available to reduce theft and vandalism


All-Sign Top Mounts & Crosspieces This unique line of top mounts and crosspieces use a bolt thru style sign mounting without a sign slot. This way it is compatible with both standard flat and extruded signs as well as any thickness of other signs.

4-CA45 Installation Specifications:

For Stacking Signs At 45°

Sign Angle: 45°


4-CA45 (U) None

4-CA45 (ZP) Zinc Plated Nuts and Bolts

4-CA45 (SS) Stainless Steel Nuts and Bolts

7” Sign Holder Vandal resistant nuts and bolts are available to reduce theft and vandalism

• Sign-to-Sign Installation • 3/8” Bolt Thru Sign Mounting: - 5” Center to Center - 1/2” From Bottom Edge to Center

2-RA238 3-RA238 Installation Specifications:

For Top Mounting Signs • Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting - 5” Center to Center - 1/2” From Bottom Edge to Center • Clamps to 2-3/8” Round Posts


2-RA238 (U) 3-RA238 (U) None

2-RA238-ZP 3-RA238-ZP Zinc Plated Nuts and Bolts

2-RA238-SS 3-RA238-SS Stainless Steel Nuts and Bolts


2-CA90 3-CA90 Installation Specifications:

For Stacking Signs At 90° • Sign-to-Sign Installation • 3/8” Bolt Thru Sign Mounting - 5” Center to Center - 1/2” From Bottom Edge to Center

Sign Angle: 90°

Sign Angle: 90°


2-CA90 (U) 3-CA90 (U) None

2-CA90 (ZP) 3-CA90 (ZP) Zinc Plated Nuts and Bolts

2-CA90 (ZP) 3-CA90 (SS) Stainless Steel Nuts and Bolts


2-RA238

3-RA238

2-CA90

3-CA90


5-1/2” Top Mounts & Crosspieces By far the most widely used style of sign brackets in North America, Dyna Engineering’s line of 5-1/2” sign brackets are manufactured from high-pressure die cast aluminum. All brackets undergo a low-sheen vibratory polishing allowing for easy handling without sharp corners while leaving an attractive surface finish. Brackets are available in this style for post mounting signs to round, U-channel or square posts. Designed with a bolt clearance hole, these brackets can mount signs by bolt thru or set screw. For sign installations using set screws, only 25-40 inch pounds of torque is required to safely secure a sign.

5-CX90 Installation Specifications:

• Sign-to-Sign Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center

Sign Angle: 90° Slot Width: 0.305”



5-CX90 (U) 5-CF90 (U) None

5-CX90 (ZP) 5-CF90 (ZP) Zinc Plated Set Screws

5-CX90 (ZPV) 5-CF90 (ZPV) Zinc Plated Vandal Resistant Set Screws*

5-CX90 (ZPVB) 5-CF90 (ZPVB) Zinc Plated Vandal Resistant Bolts*

5-CX90 (SS) 5-CF90 (SS) Stainless Steel Set Screws

5-CX90 (SSV) 5-CF90 (SSV) Stainless Steel Vandal Resistant Set Screws*

5-CX90 (SSVB) 5-CF90 (SSVB) Stainless Steel Vandal Resistant Bolts*

5-1/2” Sign Holder *HK-532P pin-hole hex key included with every order of brackets with vandal resistant fasteners


5-CF90

5-RX238 Installation Specifications:

• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 2-3/8” Round Posts

Slot Width: 0.305”



5-RX238 (U) 5-RF238 (U) None

5-RX238 (ZP) 5-RF238 (ZP) Zinc Plated Set Screws

5-RX238 (ZPV) 5-RF238 (ZPV) Zinc Plated Vandal Resistant Set Screws*

5-RX238 (ZPVB) 5-RF238 (ZPVB) Zinc Plated Vandal Resistant Set Screws and Bolts*

5-RX238 (SS) 5-RF238 (SS) Stainless Steel Set Screws

5-RX238 (SSV) 5-RF238 (SSV) Stainless Steel Vandal Resistant Set Screws*

5-RX238 (SSVB) 5-RF238 (SSVB) Stainless Steel Vandal Resistant Set Screws and Bolts*


For Top-Mounting Signs

5-RF238


5-SX134 Installation Specifications:

• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 1-3/4” Square Posts




5-SX134 (U) 5-SF134 (U) None

5-SX134 (ZP) 5-SF134 (ZP) Zinc Plated Set Screws

5-SX134 (ZPV) 5-SF134 (ZPV) Zinc Plated Vandal Resistant Set Screws*

5-SX134 (ZPVB) 5-SF134 (ZPVB) Zinc Plated Vandal Resistant Set Screws and Bolts*

5-SX134 (SS) 5-SF134 (SS) Stainless Steel Set Screws

5-SX134 (SSV) 5-SF134 (SSV) Stainless Steel Vandal Resistant Set Screws*

5-SX134 (SSVB) 5-SF134 (SSVB) Stainless Steel Vandal Resistant Set Screws and Bolts*



5-SF134


• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 2” Square Posts




5-SX200 (U) 5-SF200 (U) None

5-SX200 (ZP) 5-SF200 (ZP) Zinc Plated Set Screws

5-SX200 (ZPV) 5-SF200 (ZPV) Zinc Plated Vandal Resistant Set Screws*

5-SX200 (ZPVB) 5-SF200 (ZPVB) Zinc Plated Vandal Resistant Set Screws and Bolts*

5-SX200 (SS) 5-SF200 (SS) Stainless Steel Set Screws

5-SX200 (SSV) 5-SF200 (SSV) Stainless Steel Vandal Resistant Set Screws*

5-SX200 (SSVB) 5-SF200 (SSVB) Stainless Steel Vandal Resistant Set Screws and Bolts*



5-SF200


5-UX90 Installation Specifications:

• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center • Bolts To U-Channel, 1-3/4”+ Square Posts




5-UX90 (U) 5-UF90 (U) None

5-UX90 (ZP) 5-UF90 (ZP) Zinc Plated Set Screws and Bolts

5-UX90 (ZPV) 5-UF90 (ZPV) Zinc Plated Vandal Resistant Set Screws and Bolts*

5-UX90 (ZPVB) 5-UF90 (ZPVB) Zinc Plated Vandal Resistant Bolts*

5-UX90 (SS) 5-UF90 (SS) Stainless Steel Set Screws and Bolts

5-UX90 (SSV) 5-UF90 (SSV) Stainless Steel Vandal Resistant Set Screws and Bolts*

5-UX90 (SSVB) 5-UF90 (SSVB) Stainless Steel Vandal Resistant Bolts*


For Top-Mounting Signs At 90°

5-UF90


• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 3-1/2” Center to Center - 3/8” From Bottom Edge to Center • Bolts To U-Channel, 1-3/4”+ Square Posts




5-UX180 (U) 5-UF180 (U) None









5-UF180


5” Notched Top Mounts & Crosspieces A great design to keep signs held more securely inside of the sign slot. These notched style locking brackets are designed so that the sign blade must be loaded into the bracket by sliding the sign into the slot sideways instead of from the top. Dyna Engineering’s line of 5” sign brackets are manufactured from high-pressure die cast aluminum. All brackets undergo a low-sheen vibratory polishing allowing for easy handling without sharp corners while leaving an attractive surface finish. Brackets are available in this style for post mounting signs to round, U-channel or square posts. For sign installations using set screws, only 25-40 inch pounds of torque is required to safely secure a sign.


For Stacking Signs At 90° • Sign-to-Sign Installation • 5/16” Set Screw Sign Mounting



8-CX90 (U) None

8-CX90 (ZP) Zinc Plated Set Screws

8-CX90 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-CX90 (ZPHB) Zinc Plated Hex Bolts

8-CX90 (SS) Stainless Steel Set Screws

8-CX90 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-CX90 (SSHB) Stainless Steel Hex Bolts

5” Sign Holder *HK-532P pin-hole hex key included with every order of brackets with vandal resistant fasteners


For Top-Mounting Signs • Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Set Screws To 2-3/8” Round Posts



8-RX238 (U) None

8-RX238 (ZP) Zinc Plated Set Screws

8-RX238 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-RX238 (ZPHB) Zinc Plated Hex Bolts

8-RX238 (SS) Stainless Steel Set Screws

8-RX238 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-RX238 (SSHB) Stainless Steel Hex Bolts




For Top-Mounting Signs • Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Set Screws To 1-3/4” Square Posts



8-SX134 (U) None

8-SX134 (ZP) Zinc Plated Set Screws

8-SX134 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-SX134 (ZPHB) Zinc Plated Hex Bolts

8-SX134 (SS) Stainless Steel Set Screws

8-SX134 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-SX134 (SSHB) Stainless Steel Hex Bolts



For Top-Mounting Signs • Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Set Screws To 2” Square Posts



8-SX200 (U) None

8-SX200 (ZP) Zinc Plated Set Screws

8-SX200 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-SX200 (ZPHB) Zinc Plated Hex Bolts

8-SX200 (SS) Stainless Steel Set Screws

8-SX200 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-SX200 (SSHB) Stainless Steel Hex Bolts




For Top-Mounting Signs At 90° • Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Bolts To U-Channel, 1-3/4”+ Square Posts



8-UX90 (U) None

8-UX90 (ZP) Zinc Plated Set Screws

8-UX90 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-UX90 (ZPHB) Zinc Plated Hex Bolts

8-UX90 (SS) Stainless Steel Set Screws

8-UX90 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-UX90 (SSHB) Stainless Steel Hex Bolts



For Top-Mounting Signs At 180° • Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Bolts To U-Channel, 1-3/4”+ Square Posts



8-UX180 (U) None

8-UX180 (ZP) Zinc Plated Set Screws

8-UX180 (ZPV) Zinc Plated Vandal Resistant Set Screws*

8-UX180 (ZPHB) Zinc Plated Hex Bolts

8-UX180 (SS) Stainless Steel Set Screws

8-UX180 (SSV) Stainless Steel Vandal Resistant Set Screws*

8-UX180 (SSHB) Stainless Steel Hex Bolts



12” Top Mounts & Crosspieces Designed for the need of increasingly larger signs, these brackets can accommodate standard 9” tall street name signs. Dyna Engineering’s line of 12” length sign brackets are manufactured from high-pressure die cast aluminum. All brackets undergo a low-sheen vibratory polishing allowing for easy handling without sharp corners while leaving an attractive surface finish. Brackets are available in this style for post mounting signs to round, U-channel or square posts. Designed with a bolt clearance hole, these brackets can mount signs by bolt thru or set screw. For sign installations using set screws, only 25-40 inch pounds of torque is required to safely secure a sign.


• Sign-to-Sign Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center




12-CX90 (U) 12-CF90 (U) None

12-CX90 (ZP) 12-CF90 (ZP) Zinc Plated Set Screws

12-CX90 (ZPV) 12-CF90 (ZPV) Zinc Plated Vandal Resistant Set Screws*

12-CX90 (ZPVB) 12-CF90 (ZPVB) Zinc Plated Vandal Resistant Bolts*

12-CX90 (SS) 12-CF90 (SS) Stainless Steel Set Screws

12-CX90 (SSV) 12-CF90 (SSV) Stainless Steel Vandal Resistant Set Screws*

12-CX90 (SSVB) 12-CF90 (SSVB) Stainless Steel Vandal Resistant Bolts*



12-CF90


• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 2-3/8” Round Posts




12-RX238 (U) 12-RF238 (U) None

12-RX238 (ZP) 12-RF238 (ZP) Zinc Plated Set Screws

12-RX238 (ZPV) 12-RF238 (ZPV) Zinc Plated Vandal Resistant Set Screws*

12-RX238 (ZPVB) 12-RF238 (ZPVB) Zinc Plated Vandal Resistant Bolts*

12-RX238 (SS) 12-RF238 (SS) Stainless Steel Set Screws

12-RX238 (SSV) 12-RF238 (SSV) Stainless Steel Vandal Resistant Set Screws*

12-RX238 (SSVB) 12-RF238 (SSVB) Stainless Steel Vandal Resistant Bolts*



12-RF238



• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 1-3/4” Square Posts




12-SX134 (U) 12-SF134 (U) None

12-SX134 (ZP) 12-SF134 (ZP) Zinc Plated Set Screws and Bolts

12-SX134 (ZPV) 12-SF134 (ZPV) Zinc Plated Vandal Resistant Set Screws and Bolts*

12-SX134 (ZPVB) 12-SF134 (ZPVB) Zinc Plated Vandal Resistant Bolts*

12-SX134 (SS) 12-SF134 (SS) Stainless Steel Set Screws and Bolts

12-SX134 (SSV) 12-SF134 (SSV) Stainless Steel Vandal Resistant Set Screws and Bolts*

12-SX134 (SSVB) 12-SF134 (SSVB) Stainless Steel Vandal Resistant Bolts*



12-SF134


• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center • Set Screws To 2” Square Posts




12-SX200 (U) 12-SF200 (U) None

12-SX200 (ZP) 12-SF200 (ZP) Zinc Plated Set Screws and Bolts

12-SX200 (ZPV) 12-SF200 (ZPV) Zinc Plated Vandal Resistant Set Screws and Bolts*

12-SX200 (ZPVB) 12-SF200 (ZPVB) Zinc Plated Vandal Resistant Bolts*

12-SX200 (SS) 12-SF200 (SS) Stainless Steel Set Screws and Bolts

12-SX200 (SSV) 12-SF200 (SSV) Stainless Steel Vandal Resistant Set Screws and Bolts*

12-SX200 (SSVB) 12-SF200 (SSVB) Stainless Steel Vandal Resistant Bolts*



12-SF200



• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center • Bolts To U-Channel, 1-3/4”+ Square Posts




12-UX90 (U) 12-UF90 (U) None









12-UF90


• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Bottom Edge to Center • Bolts To U-Channel, 1-3/4”+ Square Posts




12-UX180 (U) 12-UF180 (U) None









12-UF180


6-WPX4 Installation Specifications:

• Sign-to-Post Installation • 5/16” Set Screw Sign Mounting • Screws To Nominal 4” Wood Posts (Actual Up To 3.58” SQ)




6-WPX4 (U) 6-WPF4 (U) None

6-WPX4 (ZP) 6-WPF4 (ZP) Zinc Plated Set Screws

6-WPX4 (ZPV) 6-WPF4 (ZPV) Zinc Plated Vandal Resistant Set Screws*

6-WPX4 (SS) 6-WPF4 (SS) Stainless Steel Set Screws

6-WPX4 (SSV) 6-WPF4 (SSV) Stainless Steel Vandal Resistant Set Screws*


For Top-Mounting Or End-Mounting Signs

6-WPF4


Windless® Overhead Sign Mounts These extremely strong and durable overhead sign brackets are constructed from high tensile aluminum alloy and assembled with stainless steel fasteners for complete corrosion resistance. We’ve also equipped the bracket with specialized oil-impregnated brass Oilite® bushings to self-lubricate the swinging components for a low-maintenance overhead sign system. In comparison to other cast aluminum overhead brackets which have a higher likelihood to crack or fracture under high stress windloads, Dyna Engineering’s Windless® Overhead Sign Mount brackets are designed to withstand extreme winds in all weather conditions.

®

7-OM-A-2.5 7-OM-A-4

7-OM-F-2.5 7-OM-F-4

7-ADAPTER-5-1 (U) Add-on available for sign box mounting!

7-OM-A-2.5 7-OM-A-4 7-OM-F-2.5 7-OM-F-4 Installation Specifications:

• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting - 1-1/2” Center to Center • Straps To Any Overhead Mast Arms

Strap To Post Fits Up To 3/4” Wide Band 2-1/2” Saddle Size Adjustable Length

Strap To Post Fits Up To 3/4” Wide Band 4” Saddle Size Adjustable Length

Strap To Post Fits Up To 3/4” Wide Band 2-1/2” Saddle Size Fixed Length

Strap To Post Fits Up To 3/4” Wide Band 4” Saddle Size Fixed Length

Part No: Part No: Part No: Part No: Fasteners Included:

7-OM-A-2.5 (U) 7-OM-A-4 (U) 7-OM-F-2.5 (U) 7-OM-F-4 (U) No Sign Fasteners But Includes Pre-Assembly (shown below)

7-OM-A-2.5 (SS) 7-OM-A-4 (SS) 7-OM-F-2.5 (SS) 7-OM-F-4 (SS) Stainless Steel Sign Fasteners And Includes Pre-Assembly

Easily convert to free-swing style by removing springs Easily adjustable for leveling signs to streets Complete corrosion resistant assembly Pre-assembled as shown for convenience Windless® design to release stress on posts and signs during high windloads Additional 7-ADAPTER-5-1 (U) available for backlit / sign box mounting

For Overhead Mounting Signs Equipped With Windless® Dampening System


All-Sign End Mounts This convenient line of end mounts use a bolt thru style sign mounting without a sign slot. This way it is compatible with both standard flat and extruded signs as well as any thickness of other signs. With the bolt-to-post hole centers lining up with 1” hole centers, these brackets can be mounted directly to standard 1” hole center telespar square posts without any labour-intensive drilling into sign posts which eliminates damage to city property. Similar to our other end mounts, these brackets can also be mounted to a post with stainless steel strapping.

LB-007 Installation Specifications:

For End-Mounting Signs • Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting • Bolts/Straps To 2-3/8”+ Round, 1-1/4”+ Square, All Lamp Posts

Part No:

Fasteners Included:

LB-007 (U) None

LB-007 (SS) Stainless Steel Nuts, Bolts and Washers

Requires 2 brackets to mount 1 sign Vandal resistant nuts and bolts are available to reduce theft and vandalism

SS-50 Installation Specifications:

For End-Mounting Signs

Overall Length: 6”


SS-50 (U) None

SS-50 (ZP) Zinc Plated Nuts and Bolts

SS-50 (SS) Stainless Steel Nuts and Bolts

Requires 2 halves to mount 1 sign Vandal resistant nuts and bolts are available to reduce theft and vandalism

• Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting - 4-3/4” Center to Center - 3/4” From Edge To Center • Straps To 2-7/8”+ Round, 2”+ Square, All Lamp Posts

SS-3CC5 SS-3CC5.25 SS-10CC7 SS-10CC8 Installation Specifications:

• Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting - Sign Hole Centers Shown In Left-Side Table - 3/8” From Edge To Center (If Bolting To Post) - 1/2” From Edge To Center (If Strapping To Post) • Bolts/Straps To 2-3/8”+ Round, 1-1/2”+ Square, All Lamp Posts

Sign Hole Centers: 5”

Sign Hole Centers: 5-1/4”




SS-3CC5 (U) SS-3CC5.25 (U) SS-10CC7 (U) SS-10CC8 (U) None

SS-3CC5 (ZP) SS-3CC5.25 (ZP) SS-10CC7 (ZP) SS-10CC8 (ZP) Zinc Plated Nuts and Bolts

SS-3CC5 (SS) SS-3CC5.25 (SS) SS-10CC7 (SS) SS-10CC8 (SS) Stainless Steel Nuts and Bolts

Can bolt directly to telespar posts without any extra drilling Vandal resistant nuts and bolts are available to reduce theft and vandalism



SS-406 SS-409 Installation Specifications:

For End-Mounting Signs • Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting - Sign Hole Centers Shown In Left-Side Table - 1/2” From Edge To Center • Straps To 2-3/8”+ Round, 2”+ Square, All Lamp Posts

Slot Width: 0.330” Sign Hole Centers: 5” Overall Length: 6”



SS-406 (U) SS-409 (U) None

SS-406 (ZP) SS-409 (ZP) Zinc Plated Nuts and Bolts

SS-406 (SS) SS-409 (SS) Stainless Steel Nuts and Bolts

Vandal resistant nuts and bolts are available to reduce theft and vandalism

SS-104 SS-106 SS-107 SS-109 Installation Specifications:

• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting - Sign Hole Centers Shown In Left-Side Table - 3/8” From Edge To Center • Straps To 2-3/8”+ Round, 2-1/2”+ Square, All Lamp Posts






SS-104 (U) SS-106 (U) SS-107 (U) SS-109 (U) None

SS-104 (ZP) SS-106 (ZP) SS-107 (ZP) SS-109 (ZP) Zinc Plated Nuts and Bolts

SS-104 (SS) SS-106 (SS) SS-107 (SS) SS-109 (SS) Stainless Steel Nuts and Bolts

SS-104 can also be used to end mount 6” tall extruded street name signs SS-107 can also be used to end mount 9” tall extruded street name signs Vandal resistant nuts and bolts are available to reduce theft and vandalism





Slot Width: 0.330” Overall Length: 9”


SS-209 (U) None




• Sign-to-Post Installation • 3/8” Bolt Thru Sign Mounting - 8” Center to Center - 1/2” From Edge To Center • Straps To 4”+ Round, 3-1/4”+ Square, All Lamp Posts



Slot Width: 0.185” Overall Length: 12”


SS-312 (U) None




• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting - 8” Center to Center - 3/8” From Edge To Center • Straps To 1-3/4”+ Square, All Lamp Posts


Windless® End Mounts Manufactured with the same Windless® design as Dyna Engineering’s Windless® Overhead Sign Mounts, these end mounts share the same characteristics - extremely strong, durable, and completely corrosion resistant. These end mounts are also equipped with specialized oil-impregnated brass Oilite® bushings to self-lubricate the swinging components to provide a low-maintenance solution.

7-SM-F-B 7-SM-F-S

®

7-SM-F-B 7-SM-F-S Installation Specifications:

• Sign-to-Post Installation • 5/16” Bolt Thru Sign Mounting - 1-1/2” Center to Center - 1” From Top Edge to Center

Bolt To Post 6” Saddle Size Fixed Length

Strap To Post Fits Up To 3/4” Wide Band 4” Saddle Size Fixed Length


7-SM-F-B (U) 7-SM-F-S (U) No Sign Fasteners But Includes Pre-Assembly

7-SM-F-B (SS) 7-OM-F-S (SS) Stainless Steel Sign Fasteners And Includes Pre-Assembly

7-SM-F-B Backing design ideal for post mount to 1-3/4”+ square, all lamp posts, and any flat surfaces Can bolt directly to telespar posts without any extra drilling 7-SM-F-S Backing design ideal for post mount to 2-3/8”+ round, 2-1/2”+ square, and all lamp posts Complete corrosion resistant assembly Pre-assembled as shown for convenience Windless® design to release stress on posts and signs during high windloads Windless® design also prevents signs from bending or causing damage to moving vehicles and objects passing by



15-CB1450 Installation Specifications:



15-CB1450 (U) None

15-CB1450 (ZP) Zinc Plated Set Screws

15-CB1450 (SSVB) Stainless Steel Vandal Resistant Bolts*

Can bolt directly to telespar posts without any extra drilling *HK-532P pin-hole hex key included with every order of brackets with vandal resistant fasteners

• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - sign hole locations shown in specification sheet • Bolts/Straps To 2-3/8”+ Round, 2”+ Square, All Lamp Posts

15-CB1450 (ZPV) Zinc Plated Vandal Resistant Set Screws*

15-CB1450 (SS) Stainless Steel Set Screws

15-CB1450 (SSV) Stainless Steel Vandal Resistant Set Screws*

15-CB1450 (ZPVB) Zinc Plated Vandal Resistant Bolts*




15-CB2400 (U) None

15-CB2400 (ZP) Zinc Plated Set Screws

15-CB2400 (SSVB) Stainless Steel Vandal Resistant Bolts*

Can bolt directly to telespar posts without any extra drilling *HK-532P pin-hole hex key included with every order of brackets with vandal resistant fasteners

• Sign-to-Post Installation • 5/16” Set Screw or Bolt Thru Sign Mounting - sign hole locations shown in specification sheet • Bolts/Straps To 2-3/8”+ Round, 2”+ Square, All Lamp Posts

15-CB2400 (ZPV) Zinc Plated Vandal Resistant Set Screws*

15-CB2400 (SS) Stainless Steel Set Screws

15-CB2400 (SSV) Stainless Steel Vandal Resistant Set Screws*

15-CB2400 (ZPVB) Zinc Plated Vandal Resistant Bolts*


For Offset Post Sign Mounting • Bracket-to-Post Installation • 2-3/8” Round Sign Bracket Set Screws To Mounting Base • Straps To 4-1/2”+ Round, 4-3/4”+ Square, All Lamp Posts


15-CB2050 None

AR-238R-278R adapter ring is available to convert from 2-3/8” mounting base to 2-7/8”


POST CLIP-SC Installation Specifications:

For Extruded Highway Signs • Sign-to-Post Installation • Clamp Sign Mounting • Clamps To Highway Sign Supports


POST CLIP-SC (U) None

POST CLIP-SC (SS) Stainless Steel Lock Nuts, T-Bolts, and Washers

Aluminum Alloy 356-T6

SC-180AL6 Installation Specifications:

For Side / Vertical Sign Stacking

Sign Angle 180°


SC-180AL6 (U) None

SC-180AL6 (ZP) Zinc Plated Nuts and Bolts

SC-180AL6 (SS) Stainless Steel Nuts and Bolts

Conveniently used to stack signs horizontally or vertically parallel

• Sign-to-Sign Installation • 3/8” Bolt Thru Sign Mounting - 3” Center to Center

SC-180AL2.25 Installation Specifications:

For Side / Vertical Sign Stacking

Sign Angle 180°


SC-180AL6 (U) None

SC-180AL6 (ZP) Zinc Plated Nuts and Bolts

SC-180AL6 (SS) Stainless Steel Nuts and Bolts

Conveniently used to stack signs horizontally or vertically parallel

• Sign-to-Sign Installation • 3/8” Bolt Thru Sign Mounting - 1-1/4” Center to Center


Examples of Various Sign Mounting Options

14-RF278 Installation Specifications:



14-RF278 (U) None

14-RF278 (ZP) Zinc Plated Set Screws

14-RF278 (SSV) Stainless Steel Vandal Resistant Set Screws

Twin sign panel mounting system *HK-532P pin-hole hex key included with every order of brackets with vandal resistant fasteners

• Bracket-to-Post Installation • For Use With 14-SEPBRKT-F And 14-SEPBRKT-A • Set Screws To 2-7/8” Round Posts

14-RF278 (SS) Stainless Steel Set Screws

14-RF278 (ZPV) Zinc Plated Vandal Resistant Set Screws

14-SEPBRKT-F Installation Specifications:

For Top-Mounting Signs • Sign-to-Bracket Installation • Clamp Sign Mounting • Clamps To 14-RF278

Slot Width 0.180”


14-SEPBRKT-F None

Twin sign panel mounting system Requires 2pcs 14-SEPBRKT-F to mount 1 sign

14-SEPBRKT-A Installation Specifications:

For Stacking Signs At 90° / 180° • Sign-to-Sign Installation • Clamp Sign Mounting • For Use With 14-RF278 And 14-SEPBRKT-F

Slot Width 0.180”


14-SEPBRKT-A None

Twin sign panel mounting system Requires 2pcs 14-SEPBRKT-A to stack each additional sign


ISOTM Strapping Type 201 stainless steel

Part No: Width Gauge Coil Length

BA204 1/2” 0.030” 100’

BA205 5/8” 0.030” 100’

BA206 3/4” 0.030” 100’

LG181 1/2” 0.020” 100’

LG171 5/8” 0.020” 100’

LG161 3/4” 0.020” 100’

To be used with ISOTM buckles

BA206-BLK 3/4” 0.030” 100’

Color

-

-

-

Black

-

-

-

ISOTM Buckles Type 200/300 stainless steel

Part No: Width

BU254 1/2”

BU255 5/8”

BU256 3/4”

To be used with ISOTM strapping

Band-ItTM Strapping Type 201 stainless steel

Part No: Width Gauge Coil Length

C204 1/2” 0.030” 100’

C205 5/8” 0.030” 100’

C206 3/4” 0.030” 100’

To be used with Band-ItTM buckles

Band-ItTM Buckles Type 200/300 stainless steel

Part No: Width

C254 1/2”

C255 5/8”

C256 3/4”

To be used with Band-ItTM strapping

ISOTM Wing Seals Type 200/300 stainless steel

Part No: Width

WS154 1/2”

WS155 5/8”

WS156 3/4”

To be used with ISOTM strapping

BA206-BLK Now in stock!


Bucklestraps ISOTM Strapping - Type 201 stainless steel

Part No: Width Gauge Finished Length

BA204-BU-##* 1/2” 0.030” Any

BA205-BU-##* 5/8” 0.030” Any

BA206-BU-##* 3/4” 0.030” Any

LG181-BU-##* 1/2” 0.020” Any

LG171-BU-##* 5/8” 0.020” Any

LG181-BU-##* 3/4” 0.020” Any

Set-up fee and 300’ total finished minimum length will apply *## denotes the finished length in inches - specified by customer

Bucklestraps Band-ItTM Strapping - Type 201 stainless steel


C204-BU-##* 1/2” 0.030” Any

C205-BU-##* 5/8” 0.030” Any

C206-BU-##* 3/4” 0.030” Any

Set-up fee and 300’ total finished minimum length will apply *## denotes the finished length in inches - specified by customer

Bucklestraps ISOTM Strapping - Type 201 stainless steel


BA204-BU-34 1/2” 0.030” 34”

In stock No set-up fee and only standard minimum order amounts will apply

BA205-BU-34 5/8” 0.030” 34”

Pre-fabricated Bucklestraps Our machine shop is capable of manufacturing pre-fabricated strapping hardware using standard stainless steel strapping cut to length with a tapered end on one side and a permanently attached buckle on the other. This allows for quick and easy installation, saving approximately 3 minutes per sign, and reduces the number of tools brought to a job site. We have added a feature to our cutting tools which taper the ends of the strapping in order to protect the installer from any sharp or jagged edges caused by cutting the strapping with basic shears. The tapering also allows for easier entry into the bracket and the buckle when fastening.


Part No: Brand Minimum

Width Maximum

Width Maximum

Gauge Tensioning

Force

T-001 Standard 3/16” 3/4” 0.030” 2400 LBS

C-001 Band-ItTM 3/16” 3/4” 0.030” 2400 LBS

Strap Tensioning Tool

Spin Handle Tensioning Tools

Part No: Brand Minimum

Width Maximum

Width Maximum

Gauge

T-101 Standard 3/8” 3/4” 0.030”

Strap Tensioning Tool Recommended For Tensioning On Flat Surfaces

Ratchet Handle Tensioning Tools


BC2 Series Breakaways Universal Breakaway System • Anchor-to-Post Installation

• 5/16” Set Screw Mount To Anchor • 5/16” Set Screw Mount To Post Available In All Common Post Sizes

Part No: Post Type 1 Post Type 2

BC2-178R-178R 1-7/8” Round 1-7/8” Round

BC2-178R-238R 1-7/8” Round 2-3/8” Round

BC2-178R-134SQ 1-7/8” Round 1-3/4” Square

BC2-178R-200SQ 1-7/8” Round 2” Square


BC2-238R-238R 2-3/8” Round 2-3/8” Round


BC2-238R-200SQ 2-3/8” Round 2” Square


BC2-134SQ-134SQ 1-3/4” Square 1-3/4” Square

BC2-134SQ-200SQ 1-3/4” Square 2” Square


BC2-200SQ-200SQ 2” Square 2” Square

BC2-200SQ-214SQ 2” Square 2-1/4” Square


Pre-assembled as shown for convenience Sign post breakaway system protects the post anchor in the ground from damage

Installation Specifications:

BC2 Cups Only Installation Specifications:

Replacements - Cups Only Extends cup reusability when fasteners are replaced with each use

Part No: Post Type

BC2-178R (U) 1-7/8” Round

BC2-238R (U) 2-3/8” Round

BC2-134SQ (U) 1-3/4” Square

BC2-200SQ (U) 2” Square

BC2-214SQ (U) 2-1/4” Square

BC2-HW-KIT hardware kit is available for re-assembling couplers

BC2 Centerpiece Only Installation Specifications:

Replacements - Centerpiece Only Best results when the contact surfaces between the centerpiece and cups are free of debris

Part No: Post Type

BC2-CENTER-7 Works With All Combinations

More cost-effective replacement option than traditional 1-piece designs

BC2 Fasteners Only Installation Specifications:

Replacements - Fasteners Only This convenient fastener kit includes enough hardware to completely re-assemble 1 breakaway coupling

Part No:

BC2-HW-KIT Stainless Steel Nuts, Bolts, Set Screws, Washers & Galv. Cable

Stainless steel and galvanized hardware extends re-usability of the cups

Fasteners Included:

Square to Square Round to Round Round to Square

Round and Square Cups

Centerpiece - Easily Replaceable Break Portion

Fastener Kit - Complete For 1 Breakaway Coupling

A truly universal design that can easily couple any combination of sign posts together so there is no need to search for odd size combinations anymore! This easy-to-use 3-piece design allows you to mix-and-match any sign post types, in essence, you create your own “build-to-fit” coupler for whatever you need. Another benefit of this 3-piece design is that you only have to replace components as necessary. The cups can be reused and replaced as needed and the centerpiece is just a fraction of the replacement cost of traditional 1-piece designs.

Useful Tip:Useful Tip: Keep some preKeep some pre--assembled sets on hand when heading out to repair fallen assembled sets on hand when heading out to repair fallen sign posts. There’s no need to resign posts. There’s no need to re--assemble onassemble on--site.site. Bring all of the used components back to your workshop to salvage, repair Bring all of the used components back to your workshop to salvage, repair and reand re--assemble reusable parts in a more comfortable environment.assemble reusable parts in a more comfortable environment. Some threaded holes may need reSome threaded holes may need re--threading. Enjoy the savings!threading. Enjoy the savings!


BC1-238R-238R Installation Specifications:

2-3/8” Breakaway Coupling • Anchor-to-Post Installation • 5/16” Set Screw Mount To Anchor • 5/16” Set Screw Mount To Post

Part No: Post Type 1 Post Type 2

BC1-238R-238R 2-3/8” Round 2-3/8” Round

Sign post breakaway system protects the post anchor in the ground from damage

D-238 Installation Specifications:

2-3/8” Aluminum Dome Rain Cap • Press Fit Installation • Fits On Outside Of Post

Part No: Post Type 1

D-238 2-3/8” Round

Prevent water build up and corrosion inside posts Adds decorative dome-top appearance

P-238-O Installation Specifications:

2-3/8” Plastic Flat-Top Rain Cap • Press Fit Installation • Fits On Outside Of Post


P-238-O 2-3/8” Round

Prevent water build up and corrosion inside posts Adds decorative low profile appearance UV stabilizers added into plastic to extend life

P-238-I Installation Specifications:

2-3/8” Plastic Plug Rain Cap • Press Fit Installation • Fits On Inside Of Post


P-238-I 2-3/8” Round

Prevent water build up and corrosion inside posts Won’t be seen when viewed from the ground UV stabilizers added into plastic to extend life


DR-38AL1 Installation Specifications:

Aluminum Drive Rivet • Sign-to-Post or Post-to-Anchor Installation • Body Diameter: 3/8” • Head Diameter: 1” • Grip Range: 0.233” to 0.330”

Aluminum Body and Pin


DR-38AL1 (U) None

Jumbo head 1” diameter provides substantially greater surface area clamping support Head installs flush with sign face to increase vandal resistance Easy installation with a typical hammer When using drive rivets to install signs to posts: Drive rivets can be used to clamp just about any type of sign to a post including aluminum, plastic, or wood signs. Use nylon washers to protect the reflective sheeting on the signs Minimum sign thickness combinations with sign post and washer: 0.066” minimum sign thickness when combined with 12GA post and 0.062” thick washer* 0.088” minimum sign thickness when combined with 14GA post and 0.062” thick washer* *An additional nylon washer can be added to mount thinner signs Maximum sign thickness combinations with sign post and washer: 0.163” maximum sign thickness when combined with 12GA post and 0.062” thick washer** 0.185” maximum sign thickness when combined with 14GA post and 0.062” thick washer** **Nylon washer can be excluded to mount thicker signs When using drive rivets to install sign posts to anchors: Can mount either one 12GA or 14GA sign post to one or two layers of 12GA or 14GA anchors Use steel washers to adjust the clamping tension Standard telespar post / anchor thicknesses: 12 GA = 0.105” 14 GA = 0.083”

DR-38ZP1

Zinc Plated Steel Drive Rivet

Steel Body and Pin

Part No:

DR-38ZP1 (U)

DR-38ZP1 (NL) DR-38AL1 (NL) Nylon Washers (standard 0.062” thick)

A-238R Installation Specifications:

2-3/8” Round Adapter • Bracket-to-Post Installation • 2-3/8” Outside Diameter Mounting Base • Bolt Thru Mount To Post • Sign Bracket Can Set Screw Mount To Adapter


A-238R None

Adapts any square or U-channel post to transform to 2-3/8” OD

AR-238R-278R Installation Specifications:

2-3/8” to 2-7/8” Round Adapter • Bracket-to-Post Installation • 2-3/8” Inside Diameter x 2-7/8” Outside Diameter • Set Screw Mount To Post • Sign Bracket Can Set Screw Mount To Adapter


AR-238R-278R (U) None

Adapts any 2-3/8” OD round post or mounting base to transform to 2-7/8” OD

AR-238R-278R (ST) Oilized Carbon Steel Set Screws


CRB CMB Installation Specifications:

For Erecting Signs on Concrete Barriers • Concrete Barrier-to-Post Installation • CRB for 210mm and CMB for 240mm Concrete Barriers • 2-3/8” Inside Diameter


CRB (GA) CMB (GA) Galvanized Threaded Rod, Washers, Nuts and SS Hex Bolt

SP-238R63 sign post, D-238 rain cap, and HS-1 sign brackets are available for a complete assembly.

CRB CMB SP-238R63 Installation Specifications:

Sign Post for Concrete Barrier • Barrier-to-Bracket Installation • 2-3/8” Outside Diameter

Part No: Length:

SP-238R63 63” (5ft 3in)

Designed for use with CRB and CMB

SPB-278GA10 Installation Specifications:

Surface Mount Sign Post Base • Ground-to-Post Installation • 2-3/8” Inside Diameter • 8”x8” Base With 6” Hole Centers 10” Height


SPB-278GA10 (SS) Stainless Steel Set Screw

Stainless steel hex bolts are available upon request

SPB-278GA12 Installation Specifications:

Surface Mount Sign Post Base • Ground-to-Post Installation • 2-3/8” Inside Diameter • 6”x6” Base With 3.5” Hole Centers 12” Height


SPB-278GA12 (SS) Stainless Steel Set Screw


63” (5’3”) length designed for use with CRB and CMB

SPA-278GA12 SPA-278GA18 Installation Specifications:

Concrete-Embedded Sign Post Anchor • Ground-to-Post Installation • 2-3/8” Inside Diameter 12” Length 18” Length


SPA-278GA12 (SS) SPA-278GA18 (SS) Stainless Steel Set Screw



S-38AL1.125 Installation Specifications:

Solid Aluminum Sign Spacer • Sign-to-Post Installation • 5/16” or 3/8” Bolt Thru Sign and Post Mounting • 1.125” length


S-38AL1.125 (U) None

S-38AL1.125 (ZP) Zinc Plated Nuts, Bolts, and Washers (3/8” Included)

Adds support for signs on U-channel posts Shape fits into all types of U-channel posts (check U-channel depth and use appropriate length) 5/16” fasteners available

S-38AL1.125 (SS) Stainless Steel Nuts, Bolts, and Washers (3/8” Included)

S-38GA1.125 Installation Specifications:

Galvanized Steel Sign Spacer • Sign-to-Post Installation • 5/16” or 3/8” Bolt Thru Sign and Post Mounting • 1.125” length


S-38GA1.125 (U) None

S-38GA1.125 (ZP) Zinc Plated Nuts, Bolts, and Washers (3/8” Included)


S-38GA1.125 (SS) Stainless Steel Nuts, Bolts, and Washers (3/8” Included)

S-38NL1.275 Installation Specifications:

Nylon Sign Spacer • Sign-to-Post Installation • 5/16” or 3/8” Bolt Thru Sign and Post Mounting • 1.275” length


S-38NL1.275 (U) None

S-38NL1.275 (ZP) Zinc Plated Nuts, Bolts, and Washers (3/8” Included)

Nylon with UV stabilizers Adds support for signs on U-channel posts Shape fits into all types of U-channel posts (check U-channel depth and use appropriate length) Spacer will compress as the bolts are tightened 5/16” fasteners available

S-38NL1.275 (SS) Stainless Steel Nuts, Bolts, and Washers (3/8” Included)

S-38AL1.350 Installation Specifications:

Solid Aluminum Sign Spacer • Sign-to-Post Installation • 5/16” or 3/8” Bolt Thru Sign and Post Mounting • 1.350” length


S-38AL1.350 (U) None

S-38AL1.350 (ZP) Zinc Plated Nuts, Bolts, and Washers (3/8” Included)


S-38AL1.350 (SS) Stainless Steel Nuts, Bolts, and Washers (3/8” Included)

Sign Post Hardware Section - dynabrackets.com · By far the most widely used style of sign brackets...

Documents

Transcript of Sign Post Hardware Section - dynabrackets.com · By far the most widely used style of sign brackets...