Shop Drawing Review Comments - tal-co.com...The valves shall be a Watts Series 2M2 DWB...

Bekolay & Associates Ltd. Ph: 613-723-0474 2018-04-13

200-1827 Woodward Drive, Ottawa Email:[email protected]

Shop Drawing Review Comments

Consultant: Barry J. Hobin & Associates Architects 63 Pamilla St. Ottawa On. K1S 3K7

Project: Boys & Girls Club P.O.W. 1463 Prince of Wales

Contractor: Tal-Co BAL No.: 2017-17

Attn: Doug van den Ham

Sandy Davis Date: 2018-04-13

Mech Shop Drawing Review Comments

1. General: The documents in the list have been examined for general conformance with the Contract Documents prepared by

Bekolay & Associates Ltd. (BAL) for this project. This review may not be extended to any other contract, trade, division or

project. Review by BAL does not imply approval or verification of information presented in these drawings and the

responsibility for installation and performance lies solely with the Contractor submitting the documents including

dimensional conformance and co-ordination with other trades. All changes, comments and notes by BAL shall be

incorporated (at no cost to the Owner) into actual installation when indicated “Reviewed As Follows” or be included in a

re-submission (when requested).

2. Shop Drawings: submitted in the attached files

Item Description Submitted File Comments

2.1 Washing Machine box RESUB Boys & Girls Club Reno. Prince Of Wales.pdf

Reviewed, see 3.1

2.2 Lavatories L-1 Ditto Reviewed, see 3.2

2.3 Kitchen Sink KS-1 Ditto Reviewed, see 3.3

2.4 Kitchen Sink KS-2 Ditto Reviewed, see 3.4

2.5 Hand sink Ditto Reviewed, see 3.5

2.6 Water Closet WC-1 Ditto Reviewed, see 3.6

2.7 Mop Sink Ditto Reviewed, see 3.7

2.8 Floor Drain Ditto Reviewed, see 3.8

2.9 Urinal Ditto Reviewed, see 3.9

2.10 Water Closet WC-2 Ditto Reviewed, see 3.10

2.11 SGL Laundry Tub Ditto Reviewed, see 3.11

(Con’t)

Bekolay Gamble & Associates Ltd. Ph: 613-723-0474 2018-04-13

200-1827 Woodward Drive, Ottawa Email: [email protected]

3. Additional Notes:

3.1. No comment, prior submission, reviewed (2018-03-09)









3.10. No comment

3.11. No comment

For Residential and Commercial ApplicationsES-2-M2-DWB

Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––

Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––

Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. –––––––––––––––––––––––––––––––––––

Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––

2M2 DWB

2M2 DWB Rough-In Kit

2M2 DWB Finish Kit

Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.

2M2 DWB Rough-In Kit-BR

Series 2M2 DWBDuo-Clozure™ Washing MachineShutoff ValvesSize: 1⁄2" (15mm)Series 2M2 DWB Duo-Clozure™ Washing Machine ShutoffValves consist of a molded plastic enclosure with top and sideknockouts that accept the hot and cold water supply piping aswell as a 11/2" and 2" (40 and 50mm) drain knockout to accom-modate the waste drain pipe. The Duo-Clozure™ incorporates aWatts Model 2M2 Duo-Cloz™ washing machine shutoff valvethat simultaneously controls the flow of both hot and cold waterto the appliance. The Duo-Clozure™ trim plate can be decorat-ed to blend in with the wall finish. The Series 2M2’s ball-typedesign allows it to be opened to any position to throttle waterflow and minimize harmful water hammer and banging pipescaused by fast closing washing machine solenoid valves.

Features

• Decorative white faceplate that can be painted or papered tomatch wall décor

• Used to manually eliminate water pressure on supply hosesand prevent catastrophic water damage

• Connects to 11/2" or 2" (40 or 50mm) drain piping

• Side or top water supply piping

• Supplied with water pressure test plugs

• Easy to install. Models 2M2 DWB and 2M2 DWB Rough-InKit-BR. Complete with adjustable stud mounting brackets

Models

2M2 DWB Size 1/2" (15mm) ell solder con-nections for concealed piping. Contains all of the components fora complete installation.

2M2 DWB Rough-In Kit Contains components to rough-inand test piping and drain system

2M2 DWB Rough-In Kit-BR Contains components to rough-inand test piping and drain systemwith brackets

2M2 DWB Finish Kit Contains the 2M2 washing machineshutoff valve and finish trim

ES-2-M2-DWB.qxd 1/9/08 7:36 AM Page 1

WASHING MACHINE BOX

Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales

sburgess

Accepted

Dimensions — Weights

MODEL DIMENSIONS (APPROX.) WEIGHT

A A1 A2 A3 B B1 B2 Min. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kg

2M2DWB 63/16 158 6 153 53/16 132 103/16 259 77/32 183 65/8 168 721/32 195 21/2 64 3 1.4

Top View Front View Side View

Finished Wall

M

A2

A1

A

B2 B

B1

A3

ES-2-M2-DWB 0802 ©Watts Regulator Company, 2008

USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com

Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca

W a t e r S a f e t y & F l o w C o n t r o l P r o d u c t s

Typical Installations

41" min.to bottomof bracket

42" min.to box centerline

Duo-Clozure wall box supplied withadjustable stud mounting brackets foreasy installation.2M2 DWB and2M2 DWB Rough-In Kit BR

Duo-Clozure wall box roughed in with decorative faceplate installed.

SpecificationsThe contractor shall install a single-handle wash machine shut-off valve. The ball-type valve shall simultaneously control theflow of both hot and cold water to the appliance and be fittedin a decorative recessed wall box. The decorative wall box shallhave a provision for 11/2 inch and 2 inch (40 and 50 mm) drainpiping and a decorative cover.

The valves shall be a Watts Series 2M2 DWB Duo-Clozure™

Washing Machine Shutoff Valve.

Pressure — TemperatureMaximum Pressure: 150psi (10.3 bar)

Maximum Temperature: 180°F (82°C)

ES-2-M2-DWB.qxd 1/9/08 7:36 AM Page 2

WASHING MACHINE BOX


sburgess

Accepted

MEZZO™SEMI-COUNTERTOP SINK

FIRECLAY

MEZZO SEMI - COUNTERTOP SINK• Space saving design installs on a minimum

countertop depth of 13”• Fireclay china• Rear overflow• Recessed self-draining deck• Barrier-free design• Self rimming with sealant• Cutout template and mounting kit provided(Faucet shown not included)

❏ 9960.803faucet holes on 203mm (8”) centers (Illustrated)

❏ 9960.403faucet holes on 102mm (4") centers

❏ 9960.001center hole only

Nominal Dimensions:22" (559mm) wide, 21-1/2" (546mm) deepBowl sizes:19" (482mm) wide, 15” (381mm) front to back,6-7/8" (175mm) deep

Fixture Dimensions conform to ANSI Standard A112.19.9M

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.9M for Non-Vitreous China Fixtures• CAN/CSA B45 series• A1995 National Building Code, section 3.7 andCAN/CSA-B651-02 and OBC 3.8

To Be Specified

❏ Color:

❏ Faucet*:

❏ Faucet Finish:

❏ Supplies & Stops:

❏ Trap 1-1/4" (32 mm):

NOTES:DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND "P" TRAP ARE SUG-GESTED.FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEM-PLATE SUPPLIED WITH SINK.These measurements are subject to change or cancellation. No responsibility isassumed for use of superseded or voided pages.

* See faucet section for additional models available

19"(482mm)

1-3/8" (35mm) Dia.1 Hole for CHO

9960 0011-3/8" (35mm) Dia. 3 Holesfor 8" (203mm) centres9960 803

1-1/4" (32mm) Dia. 3 Holesfor 4" (102mm) centres9960 403

2-3/4"(70mm)

8"(203mm)

22"(559mm)

4"(102mm)

8"(203mm)

15"(381mm)

21-1/2"(546mm)

Countertop

10-1/2"(267mm)

11"(279mm)

13" min.(330mm)

10-1/2"(267mm)

2-1/2"(64mm)

10-1/2"(267mm)

(cut out size)

CountertopBy Others

Finished Floor

FinishedWall

8-1/4"(210mm) 6"

(152mm)

34"(864mm)

IN ONTARIO33"

(838mm)

1-3/8"(35mm)

4-3/8"(111mm)10-5/8"

(270mm)

12-7/8"(327mm)

1-1/4 O.D.WASTE

SUPPLY

SCREWNUTFLAT WASHER

#10 SCREW

MOUNTING BRACKET

COUNTERTOP - BY OTHERS

WATERPROOFBASIN

© 2002 American Standard Inc.

LAV-000SPS 9960

Top of front rim mounted 864mm (34") from finished floor.MEETS THE AMERICAN DISABILITIES ACT GUIDE-LINES AND ANSI A117.1 ACCESSIBLE AND USEABLEBUILDINGS AND FACILITIES - CHECK LOCAL CODES.

Revised 9/02

BARRIER FREE

White

L-1


sburgess

Accepted

sburgess

Accepted

L

Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.

DSP–DEMD-100 Rev. H

DEMD SeriesElectronic Lavatory Faucets (Infrared)

Note: Measurements may vary ± 6mm (0.25")

Refer to www.specselect.com for individual models. Note: Use this page as a product submittal sheet.

113 mm(4.46")

486 mm(19.13")

65 mm(2.56") 38 mm (1.50") MAX.

DECK THICKNESS

RED/BLUE TEMPERATURE INDICATORS ON NON-REMOVABLE EXTERNAL MIXER HANDLE

O-RING TO SEAL FAUCET TO DECK

175 mm(6.89")

116 mm(4.55")

DECK

32º

SENSOR, ELECTRONICS AND BATTERY

For above deck mounted sinks, the sensor requires a clearance.

For sensor clearance:

38 mm (1.5”) maximum sink lip height from deck.

SENSOR CLEARANCE

DEMD-111LF (BATTERY OPERATED WITH USER MIX)SPECIFICATION: (example)• Deck mount electronic lavatory faucet• Sensor detects user’s hand to activate

water flow• One 9V lithium battery inside spout (included)• Above deck battery and electronics• Red light indicator blinks when battery is low• Vandal resistant (wrench flat)• 0.5 gpm (1.9 L/min) spray outlet

DEMD-111 SERIES• Electronic faucet with mixer to adjust

temperatureo DEMD-111LF (Chrome)o DEMD-111LF-NS (Nickel Stainless)

OPERATIONSensing Range: • Factory set to 8.0" ± 1.5" (200 mm ± 40 mm)• Adjustable from 3.15" to 11.8" (80 mm to

300 mm) with optional remote controlMaximum Run Time: • 90 seconds, adjustable with remote con trol

OPTIONAL ACCESSORIES (Order Separately)

o 060967A• Remote Control – allows adjustment of

sensor range, maximum run time, delayedclose time, temporary shut-off for cleaningand factory settings reset

o 063256A (Chrome Only)• 0.35 gpm (1.32 L/min) spray outlet

o 060961A (Chrome)o 060961ANS (Nickel Stainless)

• 1.0 gpm (3.8 L/min) aerator

o 061118A (Chrome)o 061118ANS (Nickel Stainless)

• 1.5 gpm (5.7 L/min) Careguard®

laminar outlet

2.5

2

1.5

1

.5

000

1

2

3

4

5

6

7

8

9

10 20 30 40 50 60 70 80

STANDARD

OPTIONAL

OPTIONAL

OPTIONAL

Line Pressure (psig)

FLOW(L/min.)

FLOW(GPM)

FLOW RATE vs PRESSURE

Outlet Flow Rates

Approvals:• IAPMO certified• Complies to ASME A112.18.1/CSA B125.1• Indicates compliance to

ICC / ANSI A117.1• Verified compliant with 0.25% weighted average Pb

content regulations(Contact Delta Representative for State and/or Local Approvals.)

HARDWIRE CONVERSION OF DEMD-100 SERIES

A One 060958A DEMD plug in power supply, output 9VDC

plusOne 061168A connector kit

B One 060704A hardwire 20VA transformer (120VAC to 24VAC)

plus One 060974A DEMD converter (24VAC to 9VDC)

plusOne 061168A connector kit

Requires SEPARATE order of either:

OR

L-1


sburgess

Accepted

Description:OFFSET LAVATORY DRAIN P.O. SHALL BE SUPPLIED WITH 19 HOLE GRID PAT-TERN, CHROME FINISH, CAST BRASS, 17 GAUGE 1-1/4” X 8-3/8” BRASS TAIL-PIECE, LOCKNUT, HEAVY RUBBER GASKET, CERTIFIED BY CSA

Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.

T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.

All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.

www.osb.ca

3700WCP.O PLUG - OFFSET OPEN GRID

Certification

114"

32mm

514"

132mm

838"

213mm

218"

55mm

238"

59mm

Top View

L-1


sburgess

Accepted

Description:P-TRAP SHALL BE 1-1/4” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 7”BRASS WALLBEND, CHROME FINISH, BRASS NUTS, DEEP BELL FLANGE,LESS CLEANOUT,CERTIFIED BY CSA




www.osb.ca

110BDCP1-1/4” 20GA P-TRAP, LESS CLEANOUT

Certification

114"

32mm

10"254mm

114"

32mm43

8"

112mm

L-1


sburgess

Accepted

L-1


sburgess

Line

sburgess

Line

DROP IN SINK: LBD7508P-1LBD7508P-1 | 2000102007

Double compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2 mm), type 304 (CNS 18/10),18-10 stainless steel.Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fittings, factory applied rimseal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center back waste location. Includes 3 1/2" (89 mm) crumb cup strainer with 1 1/2" (DN38) brass tailpiece. Sink has Spillway® partition.

Model Options: LBD7508P-1/1, 1 faucet hole, 1 1/2" diameterLBD7508P-1/3, 3 faucet holes, 1 1/2" diameter, 4" centers, 8" centersetLBD7508P-1/4, 4 faucet holes total, 1 1/2" diameter, 4" centers, 8" centerset, plus 1 faucet hole 4" to the rightLBD7508P-1, Custom (non-returnable)

TECHNICAL DATA

type of basin Double Compartment

bowl depth 8''

Bowl finish satin finished

Bowl front to back 17''

Bowl left to right 15''

gross weight 10.58 kg

material stainless steel

material code 1.4301 Chrome Nickel steel V2A

material thickness grade 18 gauge (1.2 mm)

Overall front to back 22''

Overall left to right 33 1/4''

overflow no

spillway yes

faucet ledge yes

type of waste kit 3 1/2" crumb cup strainer

undercoated yes

waste hole position centre back

PROJECT INFORMATIONItem Location

Project

Number

Quote Number

Notes

Engineer’s Approval

Franke Commercial Systems | [email protected] | www.franke-commercial.com | 2016-06-22

KS-1


mailto:[email protected]

www.franke-commercial.com

sburgess

Accepted

sburgess

Accepted

net weight 7.86 kg

Franke Commercial Systems | [email protected] | www.franke-commercial.com | 2016-06-22

KS-1


mailto:[email protected]

www.franke-commercial.com

Description:P-TRAP SHALL BE 1-1/2” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 20GAUGE 7” WALLBEND, ROUGH BRASS FINISH, BRASS NUTS, LESS FLANGE,LESS CLEANOUT,CERTIFIED BY CSA




www.osb.ca

114BRBLF1-1/2” 20GA P-TRAP, LESS CLEANOUT

Certification

1012"

267mm

112"

38mm5"

127mm

KS-1


sburgess

Accepted

CCOOMMPPLLIIEESS WWIITTHH::• ASME A112.18.1/ CSA B125.1

Indicates compliance toICC/ANSI A117.1

KITCHEN FAUCETS� Signature® Pull-Out Series� Single Handle Deck Mount� Single or 3 Hole Sink Applications

Submitted Model No.: _______________________________________________Specific Features: __________________________________________________

STANDARD SPECIFICATIONS: • Single handle kitchen faucets for exposed mounting onsingle and three hole sinks.

• Centermount or 8" (203 mm) centers with optionalincluded 10 3/4" (273 mm) long escutcheon.

• 8" (203 mm) high, 9" (229 mm) long spout [includes 61/4 (159 mm) long pull-out spray] nestled in all metal hub assembly, swings 120°.

• Spout is connected to valve body with a 53" (1346 mm)long hose that extends to 34" (864 mm) usable length.

• Pull-out spout operates in an aerated or spray modevia an easy side-to-side push lever.

• Lever or loop handle shall return to neutral positionwhen faucet is turned off.

• Control mechanism shall be the diamond coatedceramic cartridge.

• Red/blue graphics on handle button to indicatehot/cold temperature.

• Touch-Clean® sprayhead.• 3/8" O.D. straight, staggered pex supply tubes –35" (889 mm) and 36" (914 mm) long.

• Standard 3/8” (10 mm) compression gasket fittings.• Integral double check valves in spout.

DSP-K-470-DST Rev. C

2 1/2" (64 mm)Max. DeckThickness

3/8” Compression Fitting

0

1

2

3

4

5

0 10 20 30 40 50 60 70 80 90

Pressure (PSI)

Flo

w (

U.S

. Gal

lon

s P

er M

inu

te) 6

0 69 138 207 276 345 414 483 552 621

0

3.8

7.6

11.4

15.1

18.9

22.7

Pressure (kPa)

Flo

w (L

iters Per M

inu

te)

WE Models

470-DST, 470-WE-DST

®

®

U P C

Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinuemodels, both without notice or obligation. Dimensions are for reference only. See current full-line price book orwww.specselect.com for finish options and product availability.

8" (203 mm)Centers 36"

(914 mm)35"

(889 mm)

9"(229 mm)

10"(254 mm)

6 5/8"(168 mm)

8"(203 mm)

1 15/16"(50 mm)

470-DST/472-DST

470-DST/472-DST


36"(914 mm)35"

(889 mm)

6 5/8"(168 mm)

2 5/16"(59 mm)Dia.


9"(229 mm)

10"(254 mm)

55 E. 111th Street, Indianapolis, Indiana 46280395 Matheson Blvd. E., Mississauga, ON L4Z 2H2© 2009 Masco Corporation of Indiana

WARRANTY• Lifetime Faucet and Finish Limited Warranty to theoriginal consumer purchaser to be free fromdefects in material and workmanship.

• 5 Year Limited Warranty for usage in all industrial,commercial and business applications.

472-DST

10 3/4" (273 mm)

KS-1


sburgess

Accepted

sburgess

Accepted

KP

C

ST

PC

CLA

SS

SY

MB

OL

KS-1


sburgess

Line

sburgess

Line

sburgess

Oval

KS-1


sburgess

Line

sburgess

Line

Franke Kindred Canada Limited P.O. Box 190, 1000 Kindred Road, Midland, Ontario, Canada, L4R 4K9 Phone: 800-465-6085 Fax: 800-361-8408

PRINTED

IN CAN

ADA

Franke Kindred Canada Limited

0106

20

7˝ [18cm]

18 9

/16˝

[47

cm]

14˝

[36c

m]

16˝ [41cm]

ø1 1/2˝ [ø4cm] TYP

18 1/8˝ [46cm]

9 1/16˝ [23cm]

8 1/16˝ [20cm]

4˝ [10cm] TYP

L B S 4 6 0 7 –19" x 18" x 7"

SpecificationModel________________________: Single bowl sink with faucet ledge.20 gauge, type 302, 18-8 stainless steel. Self rimming. Exposedsurfaces are satin finished. Underside is fully sound dampened andundercoated. Includes factory applied rim seal, installation kit, and[3-1/2"] or [1-1/2"] waste assembly.

O.D.: 18-9/16" x 18-1/8" x 7" (47cm x 46cm x 18cm)

LBS4607-1: Includes 3-1/2" crumb cup waste assembly, waste location center.

LBS4607-3: Includes 1-1/2" duplex waste assembly, waste location center.

Faucet Hole Drilling❏ 1-hole, 1-1/2" diameter❏ 3-hole, 1-1/2" diameter on 4" centers, 8" widespread❏ Other (non-returnable): _____________________________________

_________________________________________________________

To be specified:

❏ Faucets

❏ Supplies

❏ Trap

❏ Other

Vandal resistant grid:❏ 1300G (for 3-1/2" waste)❏ 100NR (for 1-1/2" waste)

C O M M E R C I A L

LBS4607-1

KS-2


sburgess

Accepted

sburgess

Accepted





www.osb.ca


Certification

1012"

267mm

112"

38mm5"

127mm

KS-2


sburgess

Accepted

CCOOMMPPLLIIEESS WWIITTHH::• ASME A112.18.1/ CSA B125.1

Indicates compliance toICC/ANSI A117.1

KITCHEN FAUCETS� Signature® Pull-Out Series� Single Handle Deck Mount� Single or 3 Hole Sink Applications

Submitted Model No.: _______________________________________________Specific Features: __________________________________________________

STANDARD SPECIFICATIONS: • Single handle kitchen faucets for exposed mounting onsingle and three hole sinks.

• Centermount or 8" (203 mm) centers with optionalincluded 10 3/4" (273 mm) long escutcheon.

• 8" (203 mm) high, 9" (229 mm) long spout [includes 61/4 (159 mm) long pull-out spray] nestled in all metal hub assembly, swings 120°.

• Spout is connected to valve body with a 53" (1346 mm)long hose that extends to 34" (864 mm) usable length.

• Pull-out spout operates in an aerated or spray modevia an easy side-to-side push lever.

• Lever or loop handle shall return to neutral positionwhen faucet is turned off.

• Control mechanism shall be the diamond coatedceramic cartridge.

• Red/blue graphics on handle button to indicatehot/cold temperature.

• Touch-Clean® sprayhead.• 3/8" O.D. straight, staggered pex supply tubes –35" (889 mm) and 36" (914 mm) long.

• Standard 3/8” (10 mm) compression gasket fittings.• Integral double check valves in spout.

DSP-K-470-DST Rev. C



0

1

2

3

4

5

0 10 20 30 40 50 60 70 80 90

Pressure (PSI)

Flo

w (

U.S

. Gal

lon

s P

er M

inu

te) 6

0 69 138 207 276 345 414 483 552 621

0

3.8

7.6

11.4

15.1

18.9

22.7

Pressure (kPa)

Flo

w (L

iters Per M

inu

te)

WE Models

470-DST, 470-WE-DST

®

®

U P C

Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinuemodels, both without notice or obligation. Dimensions are for reference only. See current full-line price book orwww.specselect.com for finish options and product availability.

8" (203 mm)Centers 36"

(914 mm)35"

(889 mm)

9"(229 mm)

10"(254 mm)

6 5/8"(168 mm)

8"(203 mm)

1 15/16"(50 mm)

470-DST/472-DST

470-DST/472-DST


36"(914 mm)35"

(889 mm)

6 5/8"(168 mm)

2 5/16"(59 mm)Dia.


9"(229 mm)

10"(254 mm)

55 E. 111th Street, Indianapolis, Indiana 46280395 Matheson Blvd. E., Mississauga, ON L4Z 2H2© 2009 Masco Corporation of Indiana

WARRANTY• Lifetime Faucet and Finish Limited Warranty to theoriginal consumer purchaser to be free fromdefects in material and workmanship.

• 5 Year Limited Warranty for usage in all industrial,commercial and business applications.

472-DST

10 3/4" (273 mm)

KS-2


sburgess

Accepted

sburgess

Accepted

KP

C

ST

PC

CLA

SS

SY

MB

OL

KS-2


sburgess

Line

sburgess

Line

sburgess

Oval

KS-2


sburgess

Line

sburgess

Line

03/03 KINDRED 1-800-465-6085 • FAX 1-800-361-8408 15

13 3

/4˝

[35c

m]

ø1 1/2˝ [ø4cm] TYP 4˝ [10cm] TYP

5 5/8˝ [14cm]

9 1/4˝ [23cm]

6 13/16˝ [17cm]

11 5/8˝ [30cm]

13 5/8˝ [35cm]

6˝ [15cm]

L B S 9 1 0 6 –14" x 14" x 6"

SpecificationModel________________________: Single bowl sink with faucet ledge.20 gauge, type 302, 18-8 stainless steel. Self rimming. Exposed surfacesare satin finished. Underside is fully sound dampened and undercoated.Includes factory applied rim seal, installation kit, and [3-1/2"] or [1-1/2"] waste assembly.

O.D.: 13-3/4" x 13-5/8" x 6" (35cm x 35cm x 15cm)

LBS9106-1: Includes 3-1/2" crumb cup waste assembly.

LBS9106-3: Includes 1-1/2" duplex waste assembly.

Faucet Hole Drilling❏ 1-hole, 1-1/2" diameter❏ 2-hole, 1-1/2" diameter on 4" centers❏ Other (non-returnable): ______________________________________

_________________________________________________________

To be specified:

❏ Faucets

❏ Supplies

❏ Trap

❏ Other

Vandal resistant grid:❏ 1300G (for 3-1/2" waste)❏ 100NR (for 1-1/2" waste)

LBS9106-1 is shown hereLBS9106-3 has same drain location

C O M M E R C I A L

LBS9106-1/3

3 Holes 8" CC

HAND SINK


sburgess

Accepted

sburgess

Accepted

Job Name ________________________________________________

Item Number _____________________________________________

Section/Tag ______________________________________________

Model Specified ___________________________________________

Architect _________________________________________________

Engineer _________________________________________________

Contractor ________________________________________________

[ ] Submitted as Shown [ ] Submitted with Variations

Date _____________________________________________________

MECHANICAL FAUCETS

2300-8ABCP

Manual and Metering Faucets

Product Type___________________________________________________Deck Mounted 8" Fixed Centers Single Lever Hot and ColdWater Mixing Sink Faucet

Features & Specifications___________________________________________________• 8" Fixed Centers• 2.2 GPM (8.3 L/min) Aerator• 4-5/8" Lever Handle• Ceramic Volume Control and Hot Water Limit StopCartridge• 3/8" Compression Flexible Stainless Steel Supply Hoses• 10" Center to Center Integral Cast Brass Swing Spout• ECAST® design provides durable brass construction withtotal lead content equal to or less than 0.25% by weightedaverage• CFNow! Item Ships in 5 Days

Performance Specification___________________________________________________• Rated Operating Pressure: 20-125 PSI• Rated Operating Temperature: 40-140ºF

Warranty___________________________________________________• Lifetime Limited Faucet Warranty• 5-Year Limited Cartridge Warranty• 1-Year Limited Finish Warranty

Codes & Standards___________________________________________________• ASME A112.18.1/CSA B125.1• California Health and Safety Code 116875 (AB1953-2006)• Vermont Bill S.152• NSF/ANSI 372 Low Lead Content• ADA ANSI/ICC A117.1

ECAST products are intended for installation where state laws and local

codes mandate lead content levels or in any location where lead content

is a concern.

Last Revision: 11/04/2013 • Date Printed: 06/13/2014 • Product specifications subject to change without notice

2100 South Clearwater DriveDes Plaines, IL

P: 847/803-5000F: 847/803-5454

Technical: 800/TEC-TRUEwww.chicagofaucets.com

HAND SINK


sburgess

Accepted

2300-8ABCPManual and Metering Faucets

Architect/Engineer Specification________________________________________________________________________________________________________Chicago Faucets No. 2300-8ABCP, Deck Mounted 8" Fixed Centers Single Lever Hot and Cold Water Mixing Sink Faucet, Chrome Plated solid

brass construction. 10" Center to Center Integral Cast Brass Swing Spout. 2.2 GPM (8.3 L/min) Pressure Compensating Softflo Aerator. 4-5/8"

Metal Lever handle(s) with Blue and Red Temperature Indicator. Ceramic quarter turn cartridge, features square tapered stem. 3/8" Compression

Flexible Stainless Steel Supply Hoses. ECAST® construction with less than 0.25% lead content by weighted average. Secondary Control Valve:

10" Center to Center Integral Cast Brass Swing Spout. This product meets ADA ANSI/ICC A117.1 requirements and is tested and certified to

industry standards: ASME A112.18.1/CSA B125.1, California Health and Safety Code 116875 (AB1953-2006), Vermont Bill S.152, and

NSF/ANSI 372 Low Lead Content.

Operation and Maintenance________________________________________________________________________________________________________Installation should be in accordance with local plumbing codes. Flush all pipes thoroughly before installation. After installation,remove spout outlet or flow control and flush faucet thoroughly to clear any debris. Care should be taken when cleaning theproduct. Do not use abrasive cleaners, chemicals or solvents as they can result in surface damage. Use mild soap and warmwater for cleaning and protecting the life of Chicago Faucet products. For specific operation and maintenance refer to theinstallation instructions and repair parts documents that are located at www.chicagofaucets.com.

Chicago Faucets, member of the Geberit Group, is the leading brand of commercial faucets and fittings in the United States,offering a complete range of products for schools, laboratories, hospitals, office buildings, food service, airports and sport facilities.Call 1.800.TECTRUE or 1.847.803.5000 Option 1 for installation or other technical assistance.

Last Revision: 11/04/2013 • Date Printed: 06/13/2014 • Product specifications subject to change without notice

2100 South Clearwater DriveDes Plaines, IL

P: 847/803-5000F: 847/803-5454

Technical: 800/TEC-TRUEwww.chicagofaucets.com

HAND SINK


http://www.chicagofaucets.com

sburgess

Accepted





www.osb.ca


Certification

1012"

267mm

112"

38mm5"

127mm

HAND SINK


sburgess

Accepted

KP

C

ST

PC

CLA

SS

SY

MB

OL

HAND SINK


sburgess

Line

sburgess

Line

sburgess

Oval

HAND SINK


sburgess

Line

sburgess

Line

M117© 2014 AS America Inc.

AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET

VITREOUS CHINA with EVERCLEAN®

AFWALL® MILLENIUM™ FloWise® ELONGATED FLUSHOMETER TOILET with EVERCLEAN®

• Wall-mountedflushometervalvetoilet• Vitreouschina• HighEfficiency,LowConsumption.Operatesintherangeof1.1gpfto1.6gpf(4.2Lpfto6.0Lpf)

• MeetsdefinitionofHET(HighEfficiencyToilet)whenusedwithahighefficiencyflushvalve(1.1gpf-1.6gpfor1.28/1.1gpfdualflush)

• MaximumPerformance(MaP)scoreof1,000gramsat1.1gpf-1.6gpf

• PermanentEverClean®antimicrobialsurfaceinhibitsthegrowthofstain-andodor-causingbacteria,mold,andmildewonthesurface

• Condensationchannel• Concealedtrapwaydesign• Elongatedbowl• Powerfuldirect-fedsiphonjetaction• 1-1/2"inletspud• Fully-glazed2-1/8"trapway• 10"x12"watersurfacearea• Staticweightloadof1,000lbs.*• 100%factoryflushtested

❏ 3351.101Elongatedbowlonly,topspud❏ 3352.101Elongatedbowlonly,topspudwith

slottedrimforbedpanholding❏ 3353.101Elongatedbowlonly,backspud❏ 3354.101Elongatedbowlonly,backspudwith

slottedrimforbedpanholding

System MaP* Score: • 1,000gramsofmiso@1.1gpfto1.6gpfwhenusedwithanAmericanStandardflushvalve

* MaximumPerformance(MaP)testingperformedbyIAPMOR&TLab.MaPReportconductedbyVeritecConsulting,Inc.andKoellerandCompany.

Component Parts: ❏ 047007-0070AInletSpud(furnishedwithbowl)

Nominal Dimensions:660x356x381mm(26"x14"x15")

Recommendedworkingpressure–between25psiatvalvewhenflushingand80psistatic

Fixtureonly,lessseat,boltcaps,andflushometervalve

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASMEA112.19.2/CSAB45.1forVitreousChinaFixtures

* Thisproductisnotrecommendedforbariatricuse.

SEEREVERSEFORROUGHING-INDIMENSIONS

Rev.2/14

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.

BARRIER FREE

To Be Specified:❏ Color:❏White❏ Seat:

❏ AmericanStandard#5901.100Heavydutyopenfrontlesscover

❏ AmericanStandard#5905.100Extraheavydutyopenfrontlesscover

❏ FlushometerValve:❏ 1.6gpf:

❏ Sensor-Operated:AmericanStandardSelectronic®

DCPower#6065.161.002(TopSpud)ACPower#6067.161.002(TopSpud)

❏ Manual:AmericanStandard#6047.161.002(TopSpud)❏ 1.28gpf:



❏ Manual:AmericanStandard#6047.121.002(TopSpud)❏ 1.6/1.1gpfDualFlush:



❏ 1.28/1.1gpfDualFlush:❏ Sensor-Operated:AmericanStandardSelectronic®


WC-1


sburgess

Accepted

sburgess

Accepted

sburgess

Accepted


NOTES:● Toilet designed to meet ADA accessibility standards when top of seat height set at 432 to 483mm (17" to 19") from finished floor.

PRODUCT3351AND3353SHOWN,3352AND3354SAMEEXCEPTWITHSLOTTEDRIMFORBEDPANHOLDING.WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING NOT RECOMMENDED).SUGGESTED2mm(1/16)CLEARANCEBETWEENFACEOFWALLANDBACKOFBOWL.TOCOMPLYWITHAREACODEGOVERNINGTHEHEIGHTOFVACUUMBREAKERONTHEFLUSHOMETERVALVE,THEPLUMBERMUSTVERIFYDIMENSIONSSHOWNFORSUPPLYROUGHING.FLUSHOMETERVALVENOTINCLUDEDWITHFIXTUREANDMUSTBEORDEREDSEPARATELY.CARRIERFITTINGASREQUIREDTOBEFURNISHEDBYOTHERS.PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORT.

IMPORTANT:DimensionsoffixturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.2.Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages

FINISHED WALL

FINISHEDFLOOR

(4) Ø 22mm(7/8") HOLES

73m

m(2

-7/8

")

660mm(26")

470mm(18-1/2")

333mm(13-1/8")

356mm(14")

191mm(7-1/2")

133mm(5-1/4")

229mm(9")381mm

(15")

41mm(1-5/8")

FINISHED WALL

FINISHEDFLOOR

660mm(26") (4) Ø 22mm

(7/8") HOLES470mm(18-1/2")

333mm(13-1/8")

356mm(14")

191mm(7-1/2")

90mm(3-9/16")

133mm(5-1/4")

229mm(9")381mm

(15")

41mm(1-5/8")

281mm(11-1/16")

321mm(12-5/8")

3351.101/3352.101

3353.101/3354.101

AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET


Rev.2/14

BARRIER FREE

WC-1


sburgess

Accepted

© 2016 AS America Inc. 9/16

SELECTRONIC® SENSOR-OPERATEDTOILET FLUSH VALVE

HARD-WIRED AC POWER, BASE MODEL

Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for accessible and usable building facilities - check local codes

SUPPLYDN 25mm(1" I.P.S.)

108 mm - 134 mm(4-1/4" - 5-1/4")

FINISHED WALL

FINISHEDFLOOR

73 mm (2-7/8")

409 mm(16-1/8")

TYPICAL WATER CLOSET INSTALLATION:AFWALL® TOILET SHOWN

293 mm(11-1/2")

-C-L-

COVER &ELECTRICAL

BOX

160 mm(6-1/4")

86 mm(3-3/8")

BASE MODEL: (Does Not Include Power Supply)

❑ 606B.161 Base Model, 1.6 gpfFor use with Hard-Wired AC or Multi-ACpower kits. 11-1/2" rough-in

❑ 606B.121 Base Model, 1.28 gpfSAME AS ABOVE


❑ 606B.761 Base Model, Dual Flush 1.6 / 1.1 gpfSAME AS ABOVE

❑ 606B.721 Base Model, Dual Flush 1.28 / 1.1 gpfSAME AS ABOVE

POWER KITS: (Must be Purchased Separately)

❑ PK00.HAC Hard-Wired AC transformer, 10’ extensioncable and capacitor module

❑ PK00.MAC Multi-AC adapter and 10” extension cable

OPERATING PRESSURE:25 psi (flowing) - 80 psi (static)

FLOW REQUIREMENT:25 gpm (94.6 L/min.)

GENERAL DESCRIPTION:Exposed, Sensor Operated Selectronic® Water Closet Flush Valve for floor-mounted or wall-hung 1-1/2" top spud bowls.Inlet includes 1" I.P.S. angle stop with back-flow protection, vandal-resistant cap, sweat solder kit, cover tube and wall flange.Outlet includes 1-1/2" vacuum breaker, spud couplingand flange.

PRODUCT FEATURES:• Electronic flush valve with Selectronic® proximity system

for “Hands Free” operation• Self-Cleaning Piston operation with integral wiper spring

prevents clogging and reduces maintenance• Piston operation delivers superior flush accuracy and

repeatability• Adjustable tailpiece• Chemical resistant EPDM seals are unaffected by chloramines and ammonia

• Valve remains closed and does not need to be reset after loss of power or water pressure

• Stadium Feature: Valve automatically switches to waterconservation mode during periods of heavy usage

• Fully Mechanical Manual Override Button can flush toilet during a power outage

• Vandal-resistant metal cover plate (for 2-gang electric box supplied by others) with no visible fasteners

• Sensor & electronic controls are fully enclosed and waterresistant

• Range can be adjusted manually or by remote control• Sanitary Flush - Valve automatically flushes after 24 hours

of non-use to clean fixture & maintain trap seal• No external volume adjustment• 5 second Arming Delay prevents unintentional flushing• 3-second Flush Delay• Can be installed left or right-handed

RECOMMENDED SPECIFICATION:Electronic proximity infrared sensor activated toilet flush valve shall feature self-cleaning piston valve. Includes a UL listed hard-wired power supply that provides 6 VDC power to run system. Includes a fully mechanical manual over-ride that can provide a complete flush without power.Includes cast brass valve body and metal cover with chrome finish and vandal resistant stop cap. Angle stop with back-flow protection and vacuum breaker included. Flush valve shall be American Standard Model # 606B.___.002

WC-1


sburgess

Accepted

sburgess

Accepted


SELECTRONIC® SENSOR-OPERATEDTOILET FLUSH VALVE


Roughing-in Dimensions

Right or Left Hand Installation

*Note: The Critical Line (-C-L-) on Vacuum Breakermust typically be 6" min. (152 mm) above fixture.Consult Codes for details.

TOP OFFIXTURE

409 mm(16-1/8")

293 mm(11-1/2")

-C-L-

116 mm(4-5/8")

86 mm(3-3/8")

72 mm(2-7/8")

DETECTION ZONE400 mm-800 mm

(15-3/4" TO 31-1/2")

2-GANG ELECTRICALBOX BY OTHERS

SUPPLYDN 25mm(1" I.P.S.)

15˚

FINISHED WALL

51 mm (2") HOLEFOR CONDUIT

108 mm-134 mm(4-1/4" TO 5-1/4")

FOR 1-1/2" TOPSPUD FIXTURES

MANUALOVERRIDE

BUTTON

*CRITICALLEVEL

45˚

180 ˚

305 mm(12" MAX.)

160 mm(6-1/4")

160 mm(6-1/4")

57 mm (2-1/4") -137 mm (5-3/8")

LISTINGS:• ASSE 1037• ANSI/ASME A112.19.2• ADA Compliant


WC-1


ES-WD-ISCA-101-LR CANADA 0535 (Dimension) Denotes Millimeters

Job Name

Job Location

Engineer

Contractor

Contractor's P.O. No.

Representative

B3

Tag:

WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manfacturing tolerances.

© Watts Drainage 2004

CANADA

CANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca

CANADA

ISCA-101-L/R Industry StandardSingle Horizontal

Adjustable Closet Carrier

SPECIFICATION: Watts Drainage Products ISCA-101-L/R Industry Standard single horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4"(102) no hub waste and 2"(51) no hub vent connections, epoxy coated cast iron patent pending compression seal faceplate assembly, epoxy coated cast iron foot supports adjustable for standard and wheelchair height, adjustable ABS nipple with integral test cap and neoprene bowl gasket, plated hardware and chrome cap nuts.

Notes:Siphon jet (4 bolt) arrangement shown. Invert faceplate assembly for blow-out (3 bolt) bowls.

Anchor legs to concrete floor with minimum 1/2" lag bolts (by others).

Options (Select One or More)Suffix Description

-M1 ABS Extended Nipple (Up to 24")

-M11 Tiling Frame

-M20 Flush Valve Support

-36 36" Long Barrel Fitting

CA-100-EXT Aux. Support System w/Extended Nipple

X = 5-3/4" Maximum with Standard Nipple

2-3/4" 6"

10-1/2"

1"

2-3/16"

3"

"X"

5/16"

NO HUB FITTING

0" MIN.4" MAX.

9"

15"

7-1/2"

4-7/8" MIN.9-1/2" MAX.

17-3/4"

FACEPLATEASSEMBLYW/COMPRESSIONSEAL

REMOVABLE LUGSFOR SHALLOW ROUGH-IN

DUAL SLOTTEDLEGS

REAR ANCHOR SUPPORT

ASTM C564COMPRESSIONGASKET

ABS NIPPLEW/INTEGRALTEST CAP

Note:Left hand carrier shown; right hand carrier is mirror image.

11-1/2 MIN."17-1/4" MAX.

5-5/16"

-M3 Galvanized Steel Nipple 7"

WC-1 CARRIER


sburgess

Accepted


MADERA™ FloWise® 16-1/2" HEIGHT 1.28 GPF FLUSHOMETER TOILET


MADERA™ FloWise® 16-1/2" HEIGHT with EVERCLEAN®

• Floor mount flushometer valve toilet• Vitreous china• Meets definition for HET (High Efficiency Toilet)• High Efficiency (4.8 Lpf/1.28 gpf)• Will also function at 1.1gpf and 1.6gpf with a

properly set dual flush valve• EverClean® surface inhibits the growth of

stain- and odor-causing bacteria, mold,and mildew on the surface

• 10" or 12" roughing-in• 16-1/2" rim height for accessible application• Condensation channel• Elongated bowl• Powerful direct-fed siphon jet action• Fully glazed 2-1/8" trapway• 10" x 12" water surface area• 1-1/2" top spud• 2 bolt caps• 100% factory flush tested

❏ 3461.128 Elongated bowl only, top spud❏ 3461.001 Same as above, Universal Bowl❏ 3462.128 Elongated bowl only, top spud with

slotted rim for bedpan holding (White only)❏ 3462.001 Same as above, Universal Bowl❏ 3465.128 Elongated bowl only, top spud

with 4 bolts❏ 3465.001 Same as above, Universal Bowl❏ 3466.128 Elongated bowl only, top spud with

slotted rim for bedpan holding with 4 bolts(White only)

❏ 3466.001 Same as above, Universal Bowl❏ 3463.128 Elongated bowl only, back spud❏ 3463.001 Same as above, Universal Bowl❏ 3464.128 Elongated bowl only, back spud with

slotted rim for bedpan holding (White only)❏ 3464.001 Same as above, Universal Bowl

Component Parts:❏ 047007-0070A Inlet spud (furnished with bowl)❏ 481310-100 Bolt caps with retainers

(furnished with bowl)

Nominal Dimensions:718 x 356 x 419mm (28-1/4" x 14" x 16-1/2")

Recommended working pressure–between25 psi at valve when flushing and 80 psi static

Fixture only, less seat and flushometer valve

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2-2008 / CSA B45.1-08 for Vitreous

China Fixtures

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.

To Be Specified:❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black❏ Seat:

❏ American Standard #5901.100 Heavy duty openfront less cover

❏ American Standard #5905.100 Extra heavy dutyopen front less cover

❏ Flushometer Valve:❏ American Standard Selectronic™ #6065.121.002

DC Power (Top Spud)❏ American Standard Selectronic™ #6065.221.007

DC Power (Back Spud)❏ American Standard Selectronic™ #6067.221.007

AC Power (Back Spud)❏ American Standard Selectronic™ #6068.221.007

Multi AC Power (Back Spud)

Revised 4/10

BARRIER FREE

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

WC-2


sburgess

Accepted

sburgess

Accepted

sburgess

Accepted


NOTES:PRODUCT 3461 AND 3463 SHOWN, 3462 AND 3466 SAME AS EXCEPT WITH SLOTTED RIM FOR BED PAN HOLDING.TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON THE FLUSHOMETER VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY ROUGHING.THIS TOILET DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10") AND A MAXIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.FLUSHOMETER VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. FLUSHOMETER VALVE REQUIREMENTS FOR 12" (305MM) ROUGH-IN: SWEAT EXTENSION NIPPLE IS REQUIRED. REFER TO VALVE MANUFACTURER AND LOCAL CODES.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

238mm(9-3/8")

419mm(16-1/2")

438mm(17-1/4")

470mm(18-1/2")

356mm(14")

338mm(13-5/16")

150mm(5-7/8")

254mm(10")

13mm(1/2")

76mm(3")

718mm(28-1/4")

C/L OF SEAT POST HOLES140mm (5-1/2") CENTERS

FINISHED WALL

FINISHED FLOOR

C/L OF OUTLET

MADERA™ FloWise® 16-1/2" HEIGHT 1.28 GPF FLUSHOMETER TOILET


711mm(28")

1-1/2"SPUD

121mm(4-3/4")

238mm(9-3/8")

419mm(16-1/2")

470mm(18-1/2")

356mm(14")

338mm(13-5/16")

150mm(5-7/8")

254mm(10")

13mm(1/2")

25mm(1")

102mm(4")

718mm(28-1/4")

C/L OF SEAT POST HOLES140mm (5-1/2") CENTERS

FINISHED WALL

FINISHEDFLOOR

C/L OF OUTLET

1" N.P.T. OR 1" C.W.T. SUPPLYTO FLUSH VALVE

3461.128/3462.128/3465.128/3466.1283461.001/3462.001/3465.001/3466.001

3463.128/3464.1283463.001/3464.001

BARRIER FREE

Revised 4/10

WC-2


sburgess

Accepted

MODEL NUMBER:

❑ 6065.121.002 FlushValvefor11-1/2"SupplyC\Ltotopofbowl,1.28gpf

❑ 6065.122.002FlushValvefor27"SupplyC\Ltotopofbowl,1.28gpf

❑ 6065.525.002 RetrofitforExistingFlushValves,1.28gpf.Replacesindustrystandardmanualandelectronicvalves.Doesnotincludethevacuumbreakerassembly,anglestoporsweatsolderkit.

OPERATING PRESSURE:OverallRange:20-125psi**Recommended:25psi(flowing)-80psi(static)

FLOW REQUIREMENT:25gpm(94.6L/min.)

**Waterpressureover80psiisnotrecommendedformostplumbingfixtures.

BATTERY LIFE:Upto4-yearlife,(approx.200,000cycles)

ACCESSORIES:• Castwallflanges(3/4",1"&1-1/2")• Solidringpipesupports(2-1/2"&6"C-E)• Splitringpipesupports(2-1/2"&6"C-E)

RECOMMENDED SPECIFICATION:Electronicproximityinfraredsensoractivatedtoiletflushvalveshallfeatureself-cleaningpistonvalve.Includesafullymechanicalmanualover-ridethatcanprovideacompleteflushwithoutbatterypower.Includescastbrassvalvebodyandmetalcoverwithchromefinish,vandalresistantstopcapandlithiumbattery.Anglestopwithback-flowprotectionandvacuumbreakerincluded.1.28gpf/4.8LpfFlushvalveshallbeAmericanStandardModel#6065.12_.002.

GENERAL DESCRIPTION:Exposed,BatteryPowered,SensorOperatedSelectronic™WaterClosetFlushValveforfloor-mountedorwall-hung1-1/2"topspudbowls.

Inletincludes1"I.P.S.anglestopwithback-flowprotection,vandal-resistantcap,sweatsolderkit,covertubeandwallflange.

Outletincludes1-1/2"vacuumbreakerwithadjustabletailpiece,spudcouplingandflange.

PRODUCT FEATURES:• ElectronicflushvalvewithSelectronic™proximitysystemfor“HandsFree”operation• Self-CleaningPistonoperationhelpspreventcloggingandreducesmaintenance

• Positivesealensuresleak-freeperformance• FullymechanicalManualOverrideButtoncanflushtoiletduringapoweroutage

• Rangecanbeadjustedmanuallyorbyremotecontrol

• Sensor&electroniccontrolsarefullyenclosedandwaterresistant

• Automaticallyflushesafter24hoursofnon-usetomaintaintrapseal• Safetytimerhelpspreventvandalismbyturningoffthevalveifsensoriscoveredformorethan1minute

• 3-secondFlushDelay• LowBatteryindicator• Batterycanbechangedwithoutturningoffthewater• Factory-installed6Vlithiumbatteryincluded• Canbeinstalledleftorright-handed• ADAcompliant

SELECTRONIC™ FloWise®

TOILET FLUSH VALVEBATTERY POWERED, SENSOR OPERATED, 1.28 GPF

©2008ASAmericaInc.L115

Revised10/09

WC-2


sburgess

Accepted

SELECTRONIC™ FloWise®

TOILET FLUSH VALVEBATTERY POWERED, SENSOR OPERATED, 1.28 GPF

LISTINGS:• ASSE1037• ANSI/ASMEA112.19.2• ADACompliant

©2008ASAmericaInc.L116

WC-2


DETAILS500CCHeavy Duty open front less cover for elongatedbowl. Plated steel check hinge with PVC wash-ers and plastic nuts.

500CCSSHeavy Duty open front less cover for elongatedbowl. Plated steel self sustaining check hingewith PVC washers and plastic nuts.

500STSCCHeavy Duty open front less cover for elongatedbowl. Stainless steel check hinge with PVCwashers, metal flat washers, lock washers andstainless steel nuts.

500STSCCSSHeavy Duty open front less cover for elongatedbowl. Self sustaining stainless steel checkhinge with PVC washers, metal flat washers,lock washers, stainless steel nuts and self sustaining check hinge.

Standard Features:• Corrosion free steel hinge posts• Check hinge posts• Extended back with concealed hinge• Integrally molded permanent and sanitary

color keyed bumpers• Corrosion free hardware• Withstands cleansers, strong chemicals• Easy clean

I n s t i t u t i o n a l C o m m e r c i a l

Solid Plastic Seats

DETAILS

SPECIFICATIONS

500 SERIES

Seats shall be Centoco No.________________Seat and cover shall be injection molded ofhigh strength, impact resistant thermoplasticwith integrally molded permanent bumpersand steel reinforced check hinges standard.

Color to be ___________________.

WC-2

500STSCC

White


sburgess

Accepted

1© 2012 Fiat Products

FIATPRODUCTS

®

Customer Service Canada1-800-387-0369www.fiat.ca

Customer Service United States1-800-442-1902

www.fiatproducts.com

MOLDED-STONE® UTILITY SINK

MOLDED STONE® UTILITY SINKDL-17-20 & DL17-206

DL-17-20• Molded Stone self-rimming, single bowl utility sink• Standard 3-1/2" (89mm) drain opening• 9-1/2" deep (24mm)

DL-17-206Same as model DL-17-20 in a six pack quantity

9/12

15"(381mm)

20"(508mm)

1-3/4"(44mm)

7-1/2"(191mm)

10"(254mm)

1-1/4"(32mm)

1-3/4"(44mm)

8"(203mm)

2"(51mm)

2"(51mm)

4"(102mm)

17"(432mm)

14"(356mm)

3-1/2"(89mm)

11"(279mm)

9-1/4"(235mm)

SERVICE SINK


sburgess

Accepted

TWO HANDLE LAUNDRY FAUCETS

COMPLIES WITH:

Suggested Specifications

Two handle deck faucet with 10.2 cm (4”) centre and 15.24 cm (6”) swing spout.

Valve mechanisms shall be of the rotating compression type.

Hot and cold stem units are interchangeable.

All operating parts above the deck are replaceable.

All exposed metal surfaces shall be chrome-plated.

Valves shall be used with replaceable chrome-plated brass seats.

Chrome handles.

Aerator

Flow restricting, 8.3 litres per minute maximum (2.2 gpm), chrome plated brass housing.

DELTA FAUCET CANADA(a division of Masco Canada Limited)420 Burbrook PlaceLondon, Ontario N6A 4L6www.deltafaucet.com

WSP-K-29W211

ASME A112.18.1 / CSA B125.1

29W211 / 29W221

Acme threads engaged at all times for long lifeLubrication lasts and water is sealed out

Buna N Nitrile Radial Seal “O” ring

Buna N Nitrile seat washer

Stainless steel screw

Nickel chrome-plated renewable brass seats

1

2

3

4

5

Brass Stem - Compression

Compression

Direct Copper Inlets

Flexible Supply Inlets

Spout End Hose Adapter

Trap Seal Primer

29W211 29W221

X XX

X

Model ModelFeatures

27W411

Model27W411

XX

XX

X X

2.0”(5.0 cm)

5.0”(11.6 cm)

1.9”(4.9 cm)

6.0”(14.0 cm)

1-1/4” (3.1 cm)max. deck thickness

4.0”(10.2 cm) 6.2”(15.8 cm)

X

SERVICE SINK


sburgess

Accepted

sburgess

Accepted

SB850 24"x24"x12"MOP SINK


sburgess

Accepted

FIATR

255 Hutchings St. • Winnipeg, MB • R2X 2R4 • Ph. 800-665-7531 • 204-633-6122 • Fx. 204-632-4854e-mail: [email protected] • website: www.fiat.ca

A subsidiary of CR/PL, L.L.C. Company – Evanston, IL

Service-Sink FaucetModel: 830-AA

General:

Material:Finish:

Specificationsand Codes:

830-AA Service Faucet - Chrome plated withvacuum breaker, integral stops, adjustable wallbrace, pail hook and 3/4” hose thread on spout.Body inlets 8” center to center, four armhandles. Valves contain renewable hub,renewable seats, swivel discs, encased washersand brass washer screws.

Commercial red brass alloy casting-rough finish.

Chrome plating exceeding requirements ofANSI/ASTM B-456-71. Indicators cold (blue) andhot (red) are included.

In the U.S.A., meets or exceeds requirements ofANSI-A112.18.1M-1979 for “Finished andRough Brass Plumbing Fixture Fittings.” InCanada, meets or exceeds the requirements ofCSA standards B125 - “Plumbing Fittings,”B64.1.1 - “Vacuum Breakers - AtmosphereType” and B64.0 - “General Requirements forBackflow Preventers and Vacuum Breakers,”and is approved under Product Class No. 681101 under Report #LM57412-1. Conforms toASSE 1001.

NOTE: These roughing measurements mayvary 1/4” (plus or minus).

3/4” (19) HOSE THREAD

VACUUM BREAKER

9-3/8” (238)2-7/8” (73)

3/4” (19)

1/2” (13) I.P.S.MALE THREADS

1/8” (3) ECCENTRIC

9” (229)APPROX.

BUCKETHOOK

1-1/2”(38)

SIDE VIEW

FRONT VIEWINTEGRAL STOPS

2-3/8” (60) DIA.

HOT COLD

8” (203)

33888_830-AA Faucet Spec. Sheet 2/27/2003 4:32 PM Page 1

MOP SINK


sburgess

Accepted

ES-WD-FD-100-C-A CANADA 0403 (Dimension) Denotes Millimeters

FD-100-C-A

SPECIFICATION: Watts Drainage Products FD-100-C-A epoxy coated cast iron floor drain with anchor flange, reversible membrane clamp with primary and secondary weepholes,1/4"(6) thick (specify diameter) adjustable nickel bronze (standard) strainer, and no hub (MJ) (standard) outlet.

Floor Drain withRound Strainer

Job Name

Job Location

Engineer

Contractor


Representative

Components:FC-1B3

* The load classifications are in accordance with the American National Standards ASME A112.21.1MASME Ratings are as follows:MD - Safe Live Load 2000-4999 lbs.(900-2250kg)The above categories are given as a guide only. Please consult factory.

BLT3-XYC

Tag:

A

8-1/8"(206)5-1/8"(130) 6"(152)

7"(178) 8"(203)

PIPE SIZE2"(51), 3"(76), 4"(102)

6"(152) NH (MJ) only

FULL 4" (102) THROATPRIMARY WEEPHOLES

REVERSIBLE MEMBRANE CLAMP

SECONDARY WEEPHOLESSEEPAGE COLLECTION SUMP

SERRATED FLANGE

B3 BODY

(P) PUSH-ON GASKET(ASTM C-564)

1/2"(13) NPT

PIPE STOP

"A" 1/4" (6)NICKEL BRONZE STRAINER

2-1/4"(57)

See Chart A

See Chart B

5"(127) Diameter, Nickel BronzeA5-1 A6-1 6"(152) Diameter, Nickel Bronze

7"(178) Diameter, Nickel BronzeA7-1 A8-1 8"(203) Diameter, Nickel Bronze

WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manufacturing tolerances.


CANADA


Std. P T X 60/61No Push Female Inside PVC/Pipe

Size Hub On Thread Caulk ABS

2"(51) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 3-3/4"(95)3"(76) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 3-3/4"(95)4"(102) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 4"(102)6"(152) 3-1/2"(89)

Chart B

Str. Dia. Min. Max.

Chart ALoad Free Area

Rating Sq. In.

5"(127)6"(152) 2-3/4"(70)

13/16"(21)7/8"(22)

2-1/2"(64) *MD 8*MD 9

7"(178)8"(203) 2-7/8"(73)

11/16"(17)7/8"(22)

2-1/2"(64) *MD 12*MD 18

-5 Sediment Bucket-6 Vandal Proof

-8

-13 All Galvanized-15 Strainer Extension (DD-50)

-F4-50 4" Round Cast Iron Funnel

-F4-1 4" Round Nickel Bronze Funnel-F6-1 6" Round Nickel Bronze Funnel

-G-50 4x9" Oval Cast Iron Funnel

-G-1 4x9" Oval Nickel Bronze Funnel


No Hub (MJ)Push On PThreaded Outlet TInside CaulkX

Backwater Valve (3" / 4" Only)

Outlet Type (Select One) Suffix Description

2"(51) Pipe Size23"(76) Pipe Size 34"(102) Pipe Size 46"(152) Pipe Size6

Pipe Sizing (Select One)Suffix Description

PVC Body w/Socket Outlet-60ABS Body w/Socket Outlet-61

Optional Body Material (NH Only)Suffix Description

NH

Ex. FD-102P-C-A5-1

Strainer (Select One)Suffix Description

Order Code: FD-10 - - -C-

-113M Special Epoxy from 3M Range

-SO Side Outlet-Z Elastomeric Flange

TRAP PRIMER CONNECTION

PUSH-ON SHOWN

-12 Galvanized Top

2

CANADA

FLOOR DRAIN


sburgess

Accepted

sburgess

Accepted

sburgess

Accepted

sburgess

Accepted

sburgess

Accepted

sburgess

Accepted

WASHBROOK™ FloWise®

UNIVERSAL URINALVITREOUS CHINA

WASHBROOK™ FloWise® UNIVERSAL URINAL

� 6590 001 Universal Top Spud

� 6515 001

6515 001

6590 001

Universal Back Spud

Nominal Dimensions: 480 x 360 x 664mm(18-7/8" x 14-1/8" x 26-1/8")

Recommended working pressure-- between 20 psi at valve when flushing and 80 psi static.

© 2011 American Standard COM-210

�When installed so top of rim is 387mm (15-1/4") from finished floor.MEETS THE AMERICAN DISABILITIES ACT GUIDELINES ANDANSI A117.1 ACCESSIBLE AND USEABLE BUILDINGS AND FACILITIES - CHECK LOCAL CODES.

• Vitreous china• Ultra High Efficiency, Low Consumption operates

in the range of 0.10 to 0.8gpf (0.5 to 3.8Lpf)• Flushing rim• Elongated 14-1/8" (360mm) rim from finished wall• Washout flush action• Extended sides for privacy• 3/4" inlet spud• Outlet connection threaded 2" inside (NPTF)• 2 Wall hangers• Fixture only, (Flush valve shown not included)• Meets ANSI flush requirements at 0.10 to 0.8gpf

(0.5 to 3.8Lpf)

BARRIER FREE

13mm(1/2)

102mm(4)

GASKET

2" N.P.T.INSIDE THREADSFINISHED WALL

13mm(1/2)

DETAIL OF OUTLET CONNECTION

To Be Specified� � �

Meets or Exceeds the Following Specifications:Compliance Certifications -• ASME A112.19.2-2008/CSA B45.1-08 for VitreousChina Fixtures

White Bone Colour:

NOTES:FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerancesestablished by ANSI Standard A112.19.2.These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

02/11

3/4"SPUD

464mm(18-1/4")

51mm(2")

238mm(9-3/8")

360mm(14-1/8")

2" N.P.T. FEMALE OUTLET CONNECTION

13mm(1/2")

387mm(15-1/4") MAX

610mm (24")

OPTIONAL

121mm(4-3/4")

3/4"SPUD

3/4" S.P.S. OR 3/4" C.W.T.SUPPLY TO FLUSH VALVE

438mm(17-1/4")

664mm(26-1/8")

REF.

464mm(18-1/4")

292mm(11-1/2")

83mm(3-1/4")

102mm(4")

480mm(18-7/8")

343mm(13-1/2")

C/L OFOUTLET

K2 HANGERS

8mm X 25mm(5/16" X 1")SLOT

64mm(2-1/2")

238mm(9-3/8")

360mm(14-1/8")

2" N.P.T. FEMALE OUTLET CONNECTION

13mm(1/2")

FINISHED FLOOR

FINISHEDWALL

387mm(15-1/4") MAX

610mm (24")

OPTIONAL

� Flush Valve:

0.8 gpf/3.8Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063101.002 DC Power (Top Spud) � Selectronic® 6062310.007 AC Power (Back Spud)0.8 gpf/3.8Lpf Flush Valve: Manual-Operated: � 6045101.0020.4 gpf/1.9Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063051.002 DC Power (Top Spud) � Selectronic® 6062305.007 AC Power (Back Spud)0.4 gpf/1.9Lpf Flush Valve: Manual-Operated: � 6045051.0020.10 gpf/0.5Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063013.002 DC Power (Top Spud) � Selectronic® 6062301.007 AC Power (Back Spud)0.10 gpf/0.5Lpf Flush Valve: Manual-Operated: � 6045013.002

� Stainless Steel Strainer: 047068-0070A

URINAL


sburgess

Accepted

sburgess

Accepted

sburgess

Accepted


BASE MODEL: (Does Not include Power Supply)

❑ 606B.101 Base Model, 1.0 gpfFor use with Hard-Wired AC or Multi-ACpower kits. 11-1/2" rough-in



❑ 606B.013 Base Model, 0.125 gpgSAME AS ABOVE

POWER KITS: (Must be Purchased Separately)

❑ PK00.HAC Hard-Wired AC transformer, 10’ extensioncable and capacitor module

❑ PK00.MAC Multi-AC adapter and 10” extension cable

OPERATING PRESSURE:20 psi (flowing) - 80 psi (static)

FLOW REQUIREMENT:10 gpm (37.9 L/min.)

RECOMMENDED SPECIFICATION:Electronic proximity infrared sensor activated toilet flush valve shall feature self-cleaning piston valve. Includes a fully mechanical manual over-ride that can provide a complete flush without power. Includes cast brass valve body and metal cover with chrome finish and vandal resistant stop cap. Angle stop with back-flow protection and vacuum breaker included. Flush valve shall be American Standard Model # 606B.___.002

57 mm (2-1/4") -76 mm (3") 115 -134 mm

(4-1/2" TO 5-1/4")

FOR 3/4" TOPSPUD FIXTURES

SUPPLYDN 20 mm(3/4" I.P.S)

292 mm(11-1/2")

FINISHED FLOOR

FINISHEDWALL

-C-L-

CRITICALLEVEL

152 mm(6") MIN.

160 mm(6-1/4")

COVER &ELECTRICAL

BOX

86 mm(3-3/8")

SELECTRONIC® SENSOR OPERATEDURINAL FLUSH VALVE


GENERAL DESCRIPTION:Exposed, Sensor Operated Selectronic® Urinal Flush Valve for 3/4" top spud urinals.Inlet includes 3/4" I.P.S. angle stop with back-flow protection, vandal-resistant cap, sweat solder kit, cover tube and wall flange.Outlet includes 3/4" vacuum breaker, spud couplingand flange.

PRODUCT FEATURES:• Exclusive Pressure Compensation feature eliminates the

need for the installer to adjust the stop valves, saving timeand money and ensuring water savings

• Electronic flush valve with Selectronic® proximity systemfor “Hands Free” operation

• Self-Cleaning Piston operation with integral wiper springprevents clogging and reduces maintenance

• Piston operation delivers superior flush accuracy andrepeatability

• Adjustable tailpiece• Chemical resistant EPDM seals are unaffected by chloramines and ammonia

• Valve remains closed and does not need to be reset afterloss of power or water pressure

• Stadium Feature: Valve automatically switches to waterconservation mode during periods of heavy usage

• Fully Mechanical Manual Override Button can flush toiletduring a power outage

• Vandal-resistant metal cover plate (for 2-gang electricbox supplied by others) with no visible fasteners

• Sensor & electronic controls are fully enclosed and waterresistant

• Range can be adjusted manually or by remote control• Sanitary Flush - Valve automatically flushes after 24 hours

of non-use to clean fixture & maintain trap seal• No external volume adjustment• 5 second Arming Delay prevents unintentional flushing• 3-second Flush Delay• Can be installed left or right-handed


URINAL


sburgess

Accepted

sburgess

Accepted

9/16

TOP OFFIXTURE

LISTINGS:• ASSE 1037• ANSI/ASME A112.19.2• ADA Compliant

Roughing-in Dimensions

Right or Left Hand Installation

*Note: The Critical Line (-C-L-) on Vacuum Breakermust typically be 6" min. (152 mm) above fixture.Consult Codes for details.

409 mm(16-1/8")

152 mm(6") MIN.

293 mm(11-1/2")

-C-L-

-C-L-

116 mm(4-5/8")

86mm(3-3/8)

72 mm(2-7/8")

DETECTION ZONE400 -800 mm

(15-3/4 TO 31-1/2)

SUPPLYDN 20 mm(3/4"" I.P.S.)

15˚

FINISHED WALL

51 mm (2") HOLEFOR CONDUIT

115 -134 mm(4-1/2" TO 5-1/4")

FOR 3/4" TOPSPUD FIXTURES

MANUALOVERRIDE

BUTTON

*CRITICALLEVEL

45˚

180 ˚

305 mm(12") MAX.

160 mm(6-1/4")

160 mm(6-1/4")

57 mm (2-1/4") -76 mm (3")

2-GANG ELECTRICALBOX BY OTHERS

SELECTRONIC® SENSOR OPERATEDURINAL FLUSH VALVE


© 2016 AS America Inc.


URINAL


ES-WD-CA-311,321 CANADA 0403 (Dimension) Denotes Millimeters

CA-311, 321

CA-311

Urinal Carriers

Job Name

Job Location

Engineer

Contractor


Representative

Tag:

SPECIFICATION: Watts Drainage Products CA-311 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate, and plated hardware.

CA-321 SPECIFICATION: Watts Drainage Products CA-321 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate and bottom bearing plate, and plated hardware.

42"(1067)

20-1/2"(521)

4-1/2"(114)

3-1/4"(83)

FIXTURE HANGERSUPPORT PLATECA-311 ASSEMBLYWHEN USED WITHOUTLOWER PLATE.CA-321 ASSEMBLYWHEN USED WITH LOWER PLATE

TO SUITFIXTURE

ROUGH-IN

LOWERBEARING PLATE

BACK OFSUPPORTBRACKET

FRONT OFSUPPORTINGPLATE

RECTANGULARSTEEL STRUCTURALUPRIGHTS

HEAVY DUTYSTEEL FOOT SUPPORTS

FIXTUREHANGERSUPPORTINGSTUDS

BEARING STUDSNOT ATTACHEDTO FIXTURE

1" x 2"(25 x 51)

NOTE: FOOT SUPPORTS SHOULD BESECURELY ANCHORED TO FLOORWITH 1/2" BOLTS AND ANCHORSBY OTHERS.

NOTE: Recommended for support of wall-hung urinals independent of wall.



CANADA


Order Code:CA-321-

Ex. CA-311-M51


Wall Thickness over 5", per add inch (single)

-M51

Wall Thickness over 12", per inch(Back to Back)

-M52

Vandal Proof Trim, Single-M53Floor to Ceiling Adaptor, Single-M59Valve Supporting Plate, Single-M60Valve Supporting Bar, Single-M61Flush Valve Piping Support, Single-M62

CA-311-OR

272

CANADA

URINAL


sburgess

Accepted

ES-WD-WUCO CANADA 0403 (Dimension) Denotes Millimeters

WUCO

SPECIFICATION: Watts Drainage Products WUCO wall cleanout with two-piece expandable cleanout plug, stainless steel access cover, and vandal proof stainless steel screw.

Expandable Line Cleanoutwith Wall Access Cover

Job Name

Job Location

Engineer

Contractor


Representative

Tag:

1-1/8"(29)(STANDARD)

"B"

EXPANDABLE PLUG

STAINLESS STEEL COVER

1-1/2"(38) Plug Size11/22"(51) Plug Size 23"(76) Plug Size 34"(102) Plug Size4

Plug Sizing (Select One)Suffix Description



CANADACANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca

Ex. WUCO-11/2

Order Code: WUCO-

1-1/2" (38)

2" (51)

3" (76)

4" (102)

4" (102)

4" (102)

6" (178)

7" (178)

"B" COVER SIZEPLUG SIZE

6" (152) 9" (229)

6"(152) Plug Size 6

197

CANADA

URINAL


sburgess

Accepted

sburgess

Accepted

sburgess

Accepted

Shop Drawing Review Comments - tal-co.com...The valves shall be a Watts Series 2M2 DWB...

Documents

Transcript of Shop Drawing Review Comments - tal-co.com...The valves shall be a Watts Series 2M2 DWB...