Shipping: LH Thomson Co. Inc. PO Box 10158 LH Thomson Co. … · 2017-11-01 · (5.5 ) Handlebar...
2
STEM STEM MADE IN THE WARNING: Congratulations ! Make sure there are no burrs S m o o t h R a d i u s Steerer Tube Use only specially designed Thomson shims with the Thomson Stem. Standard shims will not work. REVISION SM-04.27.2004 DESIGNED BY PRODUCTM.COM phone: 478.788.5052 fax: 478.788.1956 web: www.lhthomson.com email: [email protected] Spare Parts Available Assembling the Stem STEERER CLAMP STEERER CLAMP HANDLEBAR CLAMP BOLT STEM BODY BOLT BOLT WARNING: Torque Wrench Required for assembly. Torque Specifications Bolts that are too loose or too tight can cause failure. Torque Wrench Required Steerer clamp bolts 48 in-lb. (5.5 nm) Handlebar clamp bolts 48 in-lb. (5.5 nm) Before starting assembly, 1 2 Important: For carbon fiber steerer tubes refer to the manufacturer's specifications on how to properly cut and finish the carbon fiber steerer tube. For steel and Aluminum steerer tubes: Remove any burrs from the steerer tube; do not remove any base metal. File a smooth radius around the top edge as shown. If the Thomson stem has a burr at a point of contact with the steerer tube, handlebars, or clamp, remove them with 400 grit sandpaper. Do not remove any base metal or anodized finish. Grease all of the bolt threads and the nut threads inside the steerer clamp before assembly. All 6 bolts are identical. Degrease the steerer tube, the inside of the of the Thomson Stem and the steerer clamps before assembly. Rubbing alcohol is an effective degreaser. Grease Grease Typ. Typ. 3 4 Mailing: LH Thomson Co. Inc. PO Box 10158 Macon, Georgia USA 31297-0158 Shipping: LH Thomson Co. Inc.7800 N.E. Industrial Blvd. Macon, Georgia USA 31216-7748 THANK YOU for purchasing the Thomson Stem. The following instructions should be read completely before installation. If you have any questions regarding installation or service of this product, please contact your local dealer. We recommend that a professional bicycle mechanic install and service this product. Tested to a New Unit of Measure Degrease Carbon Fiber and Aluminum Steerers Leave no more than a 3mm gap from the top of the stem to the top surface of the steerer tube. Steerer Tube 3mm (0.118") Carbon, Aluminum or Steel
Transcript of Shipping: LH Thomson Co. Inc. PO Box 10158 LH Thomson Co. … · 2017-11-01 · (5.5 ) Handlebar...
STEMSTEM
MADE IN THE
W ARN IN G :
Congratulations !
Make sure there are no burrs
Smooth Radius
Steerer Tube
Use only specially designed Thomson shims with the Thomson Stem. Standard shims will not work.
REVIS
ION
SM-04
.27.
2004
DES
IGNED
BY PR
ODUC
TM.CO
M
phone: 478.788.5052 fax: 478.788.1956 web: www.lhthomson.com email: [email protected]
Spare Parts AvailableAssembling the Stem
STEERER CLAMP
STEERER CLAMP
HANDLEBAR CLAMP
BOLT
STEM BODY
BOLT
BOLT
W ARN IN G : Torque Wrench Required for assembly.
Torque Specifications
Bolts that are too loose or too tight can cause failure.Torque WrenchRequired
Steerer clamp bolts 48 in-lb. (5.5 nm)
Handlebar clamp bolts 48 in-lb. (5.5 nm)
Before starting assembly, 1 2 Important: For carbon fiber steerer tubesrefer to the manufacturer's specifications on how to properly cut and finish the carbon fiber steerer tube.
For steel and Aluminum steerer tubes: Remove any burrs from the steerer tube; do not remove any base metal. File a smooth radius around the top edge as shown. If the Thomson stem has a burr at a point of contact with the steerer tube, handlebars, or clamp, remove them with 400 grit sandpaper. Do not remove any base metal or anodized finish.
Grease all of the bolt threads and the nut threads inside the steerer clamp before assembly. All 6 bolts are identical.
Degrease the steerer tube, the inside of the of the Thomson Stem and the steerer clamps before assembly. Rubbing alcohol is an effective degreaser.
Grease
GreaseTyp. Typ.
3 4
Mailing:LH Thomson Co. Inc. PO Box 10158Macon, Georgia USA 31297-0158
Shipping:LH Thomson Co. Inc.7800 N.E. Industrial Blvd. Macon, Georgia USA 31216-7748
THANK YOU for purchasing the Thomson Stem. The following instructions should be read completely before installation. If you have any questions regarding installation or service of this product, please contact your local dealer. We recommend that a professional bicycle mechanic install and service this product.
Tested to a New Unit of Measure
Degrease
Carbon Fiber and Aluminum Steerers Leave no more than a 3mm gapfrom the top of the stem to the topsurface of the steerer tube.
Steerer Tube
3mm(0.118")
Carbon, Aluminumor Steel
