SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode...
-
Upload
hector-spencer -
Category
Documents
-
view
219 -
download
1
Transcript of SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode...
![Page 1: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/1.jpg)
SHIELDED METAL ARC WELDING
![Page 2: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/2.jpg)
PROCESS
Arc melts base metal and end of electrode.
Melted electrode crosses arc and is deposited in the weld pool to form weld bead.
Protective covering of electrode is melted which forms gas that protects weld from Oxygen & Nitrogen.
Slag is formed
![Page 3: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/3.jpg)
![Page 4: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/4.jpg)
DANGERS
Arc- heat, light, molten metal. Infrared & ultraviolet light
Surrounding area- clear area of combustible materials
Electrical Hazards- do not service welding machines, do not use near water
Ventilation- remove smoke and fumes, keep head out of fumes
![Page 5: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/5.jpg)
TERMINOLOGY
Crater- depression at the end of a weld
DC- current that flows in only one direction
Flux- Material used to prevent oxides
Arc blow- arc wanders from intended course. Caused by magnetism
![Page 6: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/6.jpg)
TERMINOLOGY
Reversed polarity- arrangement of arc welding leads where wok is negative pole and electrode is the positive pole
Straight polarity- arrangement of arc welding leads where work is the positive pole & electrode is the negative pole
![Page 7: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/7.jpg)
EQUIPMENT
• Power source- constant
• Work clamp
• Electrode clamp
• Lead
![Page 8: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/8.jpg)
EQUIPMENT
![Page 9: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/9.jpg)
EQUIPMENT SET-UP
Protective equipment
Prepare machine
• Connect ground
• Set voltage
• Turn on machine
• Put electrode in holder
![Page 10: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/10.jpg)
MACHINE SETTINGS
DC electrode negative (straight polarity)
105-110 amps
![Page 11: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/11.jpg)
STRIKING THE ARC
• Can use a motion like a match
• Vertical tapping
If electrode gets stuck, break loose by quick twisting motion.
![Page 12: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/12.jpg)
TECHNIQUE
Goal: Weld should be two electrode diameters wide
Arc length: one electrode diameter
Should sound like frying.
Similar to MIG welding. Slow circles! SLOW.
Work on uniformity
After completing weld you must clean with a chipping hammer and wire brush
![Page 13: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/13.jpg)
TIPS
Hold electrode nearly vertical
Reverse direction of travel at end of bead to fill crater
Remove slag before doing another bead
![Page 14: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/14.jpg)
TROUBLESHOOTING
Arc too long- uneven crackling sound, spatter, bead too wide
Arc too short- buzzing sound, electrode sticks to work, narrow bead
Travel speed too low- large bead, warped plate
Travel speed too fast- bead too narrow
![Page 15: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/15.jpg)
ADVANTAGES
• Simple
• Cheap upfront cost
• Low cost
• Great penetration
• Change quickly between applications
• Many applications- electrode choices
• Mobile
• All positions
• Outdoors
![Page 16: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/16.jpg)
DISADVANTAGES
• Doesn’t deposit as much metal as GMAW
• Frequent stops/starts (electrode length)
• Lacks efficiency- electrode stubs
• More difficult
• Time- slag removal
![Page 17: SHIELDED METAL ARC WELDING. PROCESS Arc melts base metal and end of electrode. Melted electrode crosses arc and is deposited in the weld pool to form.](https://reader030.fdocuments.net/reader030/viewer/2022032600/56649dbe5503460f94ab10a6/html5/thumbnails/17.jpg)
READING ELECTRODES