Shield 200 EasyProtect Kit - English Manual
Transcript of Shield 200 EasyProtect Kit - English Manual
I N S T A L L A T I O N A N D U S E R M A N U A L
G S M V O H 1 0 0 1
1 . S t at u s / G S M S i g n al I n d i c at o r2 . P o w e r s t a t u s I n d i c a t o r3. P an i c ( S O S )4 . P an e l5 . S t an d6 . M o n i t o r i n g M I C
SIM 1 . S I M C a r d S l o t2 . C o n n e c t 3. P o w e r 4 . A d a p t e r I n t e r f ac e5 . U S B U p g r ad e P o r t
2 3
- 32 - b i t h i g h s p e e d p r o c e s s o r , r e l i a b l e c ap ab i l i t y- 1 0 0 % w i r e l e s s D . I . Y . - B u i l t - i n 1 , 0 0 0 , 0 0 0 R F c o d e s- S u p p o r t s 1 0 r e m o t e c o n t r o l s an d 1 0 0 w i r e l e s s s e n s o r s .- T h e a l ar m s y s t e m c an b e c o n t r o l l e d b y S M S , A p p o r p h o n e c al l - S t o r e s 5 p h o n e n u m b e r s an d 5 S M S n u m b e r s f o r al ar m al e r t - S u p p o r t s e x i t an d e n t r y d e l a y ar m / al e r t- W i r e l e s s s e l f - l e ar n i n g c o d e- A d d i n g n e w ac c e s s o r i e s f a s t an d e a s y- S u p p o r t s ar m an d d i s ar m b y A p p- S u p p o r t s r e m o t e m o n i t o r b y A p p- S u p p o r t s r e m o t e c o n t r o l / ar m / d i s ar m / m o n i t o r b y p h o n e- S M S f o r p o w e r p o w e r r e c o v e r y an d l o w - S u p p o r t s g l o b a l G S M 85 0 / 90 0 / 1 80 0 / 1 90 0 M H z
C o n tro l P an e l F e atu re s
F e atu re s
1 . S tatu s / L o w P o w e r I n d i c ato r
B l u e s y s t e m i s ar m e dB l u e t h e al ar m h as b e e n t r i g g e r e d
2 . P o w e r / G S M S i g n al I n d i c ato r
P r o d u c t S h i e l d 2 0 0
P o w e r s u p p lI n p u t A C 1 1 0 ~ 2 4 0 V / 5 0 ~ 6 0 H z
D C 1 2 V / 1 A
G S M w o r k i n g f r85 0 / 90 0 / 1 80 0 / 1 90 0 M H z
S t an d b y c u r r e n6 0 m A h
A l ar m c u r r e n1 2 0 m A h
B u i l t - i n 7 . 4 V 6 0 0 m A h l i t h i u m
S u p p o r t w i r e l e s s 1 0 r e m o t e c o n t r o l , 1 0 0 w i r e l e s s d e t e c t o r s
W i r e l e s s r e c e i v i n g f r 4 33M H z ( ± 7 5 K H z )
S i r e n v 90 d B
H o u s i n g m a tA B S
T e m p e r a t u r - 1 0 ° C ~ + 5 5 ° C ≤80%
( n o n - c o n d e n s i n g )
4 5
Quick Start-up Guide
First
Store a phone numberTo interact with the control panel by SMS, by phone call and/or from the app, at least one phone number must be stored in the control panel. Please refer to the on “Store Phone Numbers” on page 7 of this manual.
Change the languageBy default the language of the kit control panel is set to English. If you wish to change the system language, refer to the “Change system language” on page 12 of this manual. “System language” refers to the language of the SMS you receive from the control panel.
Arm / Disarm the system
The alarm system can be armed or disarmed by SMS, by App and by phone call.
By SMS To arm the system: Send “1” by SMS to the number of your system’s SIM card.To disarm the system: Send “0” by SMS to the number of your system’s SIM card.
By appClick on “Arm” in the app to arm the system, and “Disarm” to disarm the system. The app is available for download on the App Store and Google Play.
Register wireless accessories
Control by Phone Call
Method 1When an alarm has been triggered, the control panel dials the pre-stored phone numbers. When you pick up the phone, control the panel from distance according to the in the table below).
Method 21. Dial the telephone number of the SIM card in your control panel.2. Enter your user code, followed by ”#”. ey you press on your phone, you hear one beep
3. Select the to control the panel (see in the table below).
NoteThe call will end ally if you do not send any command within 30 seconds.
Voice
Command
Press “1“ Arms the system
Press “0“ --
--
--
- Stops monitoring without hanging up
Press “ “
Press “6“ Turns all sirens
Press “9“
Press “#“ -- Exits control by phone call
- Stops call recycles
NoteIn GSM mode, the audio monitoring is not limited in
Hard Reset
Press the Connect and the Panic (SOS) simultaneously. Release them 3 beeps. Wait 10 seconds. The panel beeps twice: the system is restored to default Stored phone numbers and accessories will also be deleted.
successful.
If the accessory has already been registered, the control panel will beep twice. The first accessoryregistered is assigned to zone 1, the second accessory registered is assigned to zone 2, etc. Zones
learn how to rename zones).
Disarms the system and turns the siren off
Stops the built-in siren and the wireless siren (if connected to the control panel)
Turns the wireless siren on (if connected to the control panel)
Turns all sirens off
6 7
Zone setup of accessories
Every detector can be assigned to 4 t categories of zones: Home Mode Zone, Delay Zone, Normal Zone and 24-H Zone. To assign a detector to a zone, open its case and move its jumpers according to the drawing below:
D0
D3
D0
D3D0
D3 D3
D0
A. Home Mode Zone B. Delay Zone C. Normal Zone D. 24-H Zone
Normal zoneWhen the system is armed, if a sensor is triggered, the siren rings out. When the system is disarmed, sensors do not trigger an alarm.
24h zoneRegardless the system is armed or disarmed, sensors assigned to the 24h zone can trigger an alarm. It is recommended to set smoke detectors, gas detectors and outdoor beam sensors in the 24-H zone.
Delay zoneAn entry and an exit delay can be set. In such case, sensors assigned to the “Delay Zone” will not trigger an alarm during the of delay set. For example, if you assign a detector to the Delay zone and you set the Entry/Exit Delay to 30 seconds, the detector will not trigger an alarm within 30 seconds you enter your home and within 30 seconds before you leave it so that you can leave and enter your home without triggering an alarm. Refer to the on page 6 of this manual to learn how to set the entry and exit delay. It is recommended to assign the Door / Window Contact to the Delay zone.
Home zoneWhen the system is armed in Home Mode, the sensors assigned to the Home zone do not trigger an alarm. It is recarmed in Home Mode when you are home and move inside your home without triggering any alarm.
SMS
IMPORTANT: BEFORE USING FOR THE FIRST TIME
SAVE A PHONE NUMBER FOR SMS NOTIFICATIONS. (Refer to on the opposite column)Only stored numbers can control and
INSERT A SIM CARD IN THE CONTROL PANEL
Each SMS opera in this user manual will be illustrated as follows:
You send:
SMS Command
command sent by the user.
The control panel replies:
Control panel’s reply
by the control panel.
The speech bubbles that follow are the dialogue between the user and the control panel (SMS sent by the user are in pink, SMS sent by the control panel are in grey).
The system is in English by default. To change the system’s language, refer to page 12 of this manual.
Store Phone numbers for SMS
Send:
6
SMS numbers:1.2.3.4.5.
Copy, Paste, then Edit(case
SMS numbers:1. 0678900332. 0678900223. 0678900114. 0678900005.
Ok
7
BEFORE STARTING SMS OPERATIONS .
MAKE SURE THE SIM CARD DOES NOTREQUIRE ANY PIN CODE .
8 9
Disarm the System
Send:
0
System disarmed.
Arm the System
Send:
1
System armed.
Home Mode
Send:
2
System in home mode.
Enquiry
Send:
00
System:DisarmedAC power:onEntry delay Exit delay Siren Disarm password:1234
NoteThe value of default will be changed
er having set up the system.
Store Phone Numbers
Send:
5
Phone numbers:1.2.3.4.5.
Copy, Paste, then Edit(case e):
Phone numbers:1. 0678900332. 0678900223. 0678900114. 0678900005.
Ok
Change Zone Name
Send “91~99”. For example for zone 1, send:
91
Zones names:1.
Copy, Paste, then Edit(case e):
Zones names:1.Entrance door alarm
Ok
NoteZones 1 to 9 can be renamed. The name of the zone cannot consist of more than 30 characters per line due to SMS character limit. Zones 10 to 99 cannot be renamed.
10 11
SMS Alert for Accessory Low ery(available for two-way acessories such as
Detectors)
For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + low ery”.
Bedroom PIR low
For accessories assigned to zones that have not been renamed, an SMS will be sent under the format “Zone number + low ery”.
Zone 10 low
SMS Alert for Accessory Tamper Alarm (available for two-way acessories such as
Detectors)
For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + tamper alarm”.
Bedroom PIR tamper alarm.
For accessories assigned to zones that have not been renamed, an SMS will be sent under the format “Zone number + tamper alarm”.
Zone 10 tamper alarm.
Entry and Exit Delay Time
Send:
11
Entry delay Exit delay
Copy, Paste, then Edit(case
Entry delay Exit delay
Ok
NoteThis can be used if you do not want to bring a remote control or RFID tag with you. When the system is armed, you hear one beep every second to remind you to leave. The beep rhythm speeds up during the last 10 seconds. If an intruder is detected, the alarm will be delayed accordingly.
Siren Volume and Ringing Time
Send:
12
Siren volume(0=Mute,1=High):1Siren ringing
Copy, Paste, then Edit(case
Siren volume(0=Mute,1=High):0Siren ringing
Ok
Disarm Password
Send:
13
Disarm password (4 digits):1234
Copy, Paste, then Edit(case
Disarm password (4 digits):8888
Ok
Set Ringing Times
Send:
19
Ringing
Copy, Paste, then Edit(case
Ringing
This enables you to the number of the control panel rings before taking the call.
Ring can be set from 0 to 9. When set to 0, the alarm system will not ring when being called.
1312
Call repe
If the user does not pick up his phone when the alarm detects an intrusion, the alarm will keep re-dialing the number a certain amount of
Send:
20
Call
Copy, Paste, then Edit(case
Call
The number of call can be set from 1 to 9.
Delete all Wireless Accessories
Send:
21
Ok
Change system language
Send the code of the language. For example, for English, send “0001”.
0001
Ok
Refer to the table below for the full list of languages:
0001 English0002 French0004 Danish0006 Italian0007 Swedish0008 German
0009 Spanish0010 Finnish0011 Norwegian
Restore System to Factory by SMS
Send:
0000
Ok
The will be restored to default values. Stored phone numbers and connected accessories will also be deleted.Only stored numbers can send the SMS to restore factory
Accessories
Wireless Remote Control
Home ModeArm
SOSDisarm
LED indicator
Arm the system
Press the Arm " " to arm the alarm system. The LED indicator lights up (the siren rings out once). The system is armed.
If an intruder is detected, the siren rings out. (The siren turns 5 minutes as per default In the the system dials the pre-stored phone numbers
Disarm the system
Press the Disarm " " to disarm the alarm system. The LED indicator turns (the siren rings out twice). The system is disarmed.
Home Mode
Press the Home Mode " " on the remote control. The system state LED is on. All the sensors in regular zones are armed except those in the Home Mode zone. The sensors in the Home Mode zone are disarmed so that users can move inside their home.
0016 Czech
1514
Emergency Mode
Regardless the status of the system, the alarm is triggered when the SOS "SOS" is pressed on the remote control.At the same the control panel sends a
by SMS and dials the pre-stored phone numbers.
Register in the control panelPress the at the back of the control panel to enter the mode. Press any on of the remote control.
Power supply:DC 3V (CR2025 on ba x1)
Oper current:≤7 mA
St current:10 uA
Transmission distance≤ 80 m (in open area)
Radio-frequency:433MHz (±75KHz)
Housing material:ABS plas
cTemperature: -10°C ~ +55°CR Humidity: ≤80% (non-condensing)
Dimensions:57 x 31 x 11 mm
Wireless Detector
With automa temperature compensa and turbulence technology, it easily adapts to environmental changes.
Design
Features
3
1
2
1. LED indicator2. Detection window3. Bracket
PCB Layout
Alarm zone setupTamper switch*
Infrared sensor**
AA 1.5V LR6
Antenna
LED working indicator
*Tamper switchWhen the alarm system is armed, the tamper switch will trigger the alarm if the case isopened.
**Infrared sensorDetects the infrared rays released by humanbody Do not touch the surface. Keepthe surface clean.
LED
Blinks self Blinks once: an intruder is detectedBlinks twice: self is complete; entering working mode.Blinks once every 3 seconds: under-voltage indica the eries must be replaced. (You will be informed by SMS when the eries are low if the detector is registered in the control panel.)
The PIR motion detector is a high performance wireless motion detector boasting a digital dual-core fuzzy logic infrared control chip with intelligent analysis. This technology identifies interferences created by body motion and reduces the false alarm rate.
1716
Usage
Open the case and remove the strip. will start for 30 seconds.
When the sensor is in operation, if it is triggered more than twice within 3 minutes, it will switch to standby mode to save power. If no movement is detected within the next 3 minutes, the sensor goes back to working mode.
Connect
Register in the control panel
Press the at the back of the control panel to enter the mode. Press the connect at the back of the sensor or trigger the sensor (by moving in front of it).
Avoid the detector close to windows, air , heater, refrigerator, oven, sunshine and places where the temperature changes fast or where the air stream s frequently.
If two detectors are installed in the same det scope, adjust the loca to avoid interferences and false alarms.
Fix the bracket on the wall with screws and ach the detector to the bracket. Adjust the bracket to change the det distance and angle. It is recommended to mount the detector 2m from the ground.
Top
Ground
2.2 m
The detector is more sensitive to cross movements than vertical movements.
Side viewTop view
A. the inst turn the detector on. one minute of self-t press the test walk in the scope of det and watch the LED indicator to make sure the detector
is working.
B. The LED indicator blinks once when body movement is detected.
C. Adjust the detector angle to achieve the best de performance.
Power supplyDC 3V (AA 1.5V LR6 Ba x 2)
St current≤ 30uA
Alarm current≤ 15 mA
De scope8m / 110°
T distance≤ 80m (in open area)
Radio-frequency 433 MHz (±75 KHz)
Housing materialABS plas
cTemparature: -10°C~55°CR humidity: ≤ 80% (non-condensing)
Detector dimensions (L x W x H)107 x 53 x 32 mm
Bracket dimensions (L x W x H)52 x 30 x 26.5 mm
Scope
110°
Top view
0m 2m 4m 6m 8m2m
0m
Side view
1918
Wireless Door / Window Contact
Features
signals to the control panel when the
Thanks to the tamper switch, any t to remove the cover of the Door / Window Contact will trigger the alarm.
Design
Magnet
Transmitter
LED indicator
PCB Layout
LED working indicator
Zone setting
AAA 1.5V Battery
AAA 1.5V Battery x 1
Tamper switch
LED
Blinks once: the door or window is open and the sends a signal to the control panel.Blinks quickly: Low power indica the eries must be replaced.
Register the detector in the alarm system
Press the at the back of the control panel to enter the mode. Then separate the magnet from the er.
To check if the registr is complete, arm the system and separate the magnet from the again by opening the door or window on which it is installed. If the siren rings out,
the regis is successful.
- Open the case and remove the ery strip.- Mount the sensor on the door and the magnet on the
door frame.- Make sure the magnet is placed above the er.- Mount the magnet max. 1 cm away from the
and secure the and magnet with double-sided tape or screws.
- Avoid the sensor in areas with a large amount of metal or electrical wiring such as a furnace or room.
Power supply
current≤ 30 uA
Alarm current≤ 15 mA
Tr distance≤80 m (in open area)
Radio-frequency 433 MHz (±75 KHz)
Housing materialABS
Oper temperature-10°C~55°C
humidity≤80% (non-condensing)
T dimensions (LxWxH)60 x 45 x 18 mm
Magnet dimensions (LxWxH)45 x 19 x 17,5 mm
The door/window contact can be installed on doors, windows, and any other objucts that open and close. The sensor sends signals to the control panel when the magnet is separated from the
20 21
This keyboard enables you to arm and disarm your alarm system, or arm it in Home Mode.
27
22 23
It
24 25
The MS-10A operates under 4modes
26 27
Maxsmart
Maxsmart
MaxsmartMaxsmart
It
.
28 29
30 31
32 33
Maxsmart
34 35
36 37
38 39
VIEWONHOME This product bears the selective sorting symbol for waste electrical and electronic equipment(WEEE).This means that this product must be handled pursuant to European.Directive 2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment.For further information,please contact your local or regional authorities.Electronic products not included in the selective sorting process are potentially dangerous for the environment and human heath due to the presence of hazardous substances. In compliance with European law. This product was designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and of the Council on the restriction of use of certain hazardous substances in electrical and electronic equipment (RoHS Directive - Rohs) and is deemed to comply with the maximum concentration values set by the European Technical Adaptation Committee(TAC).Made in CHINA
Standard
Local language user manuals can be downloaded from www.viewonhome.eu or by scanning this QR code