SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO: … · SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO:...

SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO: POCE16102603TRS

H Building, Hongfa Science and Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, China

Web: http://www.poce-cert.com Tel: 86-755-29113252 E-mail:[email protected] of 5

TESTING: Testing was carried out in accordance with EN 420: 2003 + A1: 2009 & EN 388: 2003.

Unless otherwise stated, samples were conditioned for at least 24 hours in a controlled environment maintained at (23 ± 2) °C and (50 ± 5) % relative humidity. Testing was carried out within the same environment REQUIREMENTS Table 1 – Levels of performance for EN 388: 2003

Performance Level 1 2 3 4 5

Abrasion Resistance ( EN 388: 2004 §6.1)

Number of cycles (minimum) 100 500 2000 8000

Blade Cut Resistance ( EN 388:2003 §6.2)

Index (I) (minimum) 1.2 2.5 5.0 10.0 20.0

Tear Resistance ( EN 388: 2004 § 6.3)

Force (N) (minimum) 10 25 50 75 ---

Puncture Resistance ( EN 388: 2004 §6.4)

Force (N) (minimum) 20 60 100 150 ---

Table 2 – Requirements for EN 420: 2003 + A1: 2009 Clause 5 Size and Dexterity

Glove size 6 7 8 9 10 11

Minimum length / mm 220 230 240 250 260 270

Performance level 1 2 3 4 5

Diameter of dexterity pin /mm 11.0 9.5 8.0 6.5 5.0




TEST RESULTS EN 420: 2003

CLAUSE / TEST

EN 420: 2003

REQUIREMENT

TEST RESULTS UoM

(See note 1)

P/F

5.1 Glove length See table 2 Size Length / mm

L: 280, R: 280

± 0.3 mm PASS

5.2 Dexterity See table 2 Size Minimum pin diameter /

mm 8

N/A Level 3

EN 388: 2003

CLAUSE / TEST

EN 388: 2003

REQUIREMENT

TEST RESULTS UoM

(See note 1)

PASS /

FAIL

6.1 Abrasion

resistance

See table 1 Sample Failure between /

cycles

1 8000 & 8500

2 8000 & 8300

3 8000 & 8500

4 8500 & 9000

Saint-Gobain A700 Abrasive paper

used

Abrasion machine compliant with

EN ISO 12947-1:1998

Clause 6.1.3

± 10 %

See note 2

Level 4

6.2 Blade cut

resistance

See table 1 Sample Cut index

Left 20.6, 20.9, 20.8

Mean = 20.8

Right 20.4, 20.3, 20.9

Mean = 20.5

Nominal width of blade is 0.3mm

± 2.33 Level 5

6.3 Tear resistance See table 1 Sample Peak force / N

1 76.9

2 75.8

3 79.9

4 77.5

± 2.1 N Level 4

6.4 Puncture

resistance

See table 1 Sample Peak force / N

1 107.8

2 106.5

3 102.9

4 103.8

± 2.1 N Leve 3




*BANNED AZO DYES (Annex XVII of EU Regulation 1907/2006 (REACH)) (BS EN 14362-1 / BS EN 14362-2 / DD CEN ISO/TS17234:2003)

SAMPLE TEST METHOD USED REQUIREMENT

52% Palm: Synthetic Leather

(60% Nyon/40% PU)

(50% Nylon, 26% Polyester,

24% PU - Outer Palm)

(86% Para-Aramid,

14% Glass - Inner Palm)

(100% Polyester - Liner)

35% Back Stretch Nylon

(95% Nylon, 5% Spandex)

13% Airprene Gauntlet

(80% Neoprene, 20% Nylon)

Maximum permitted amount:30 ppm

4-Aminodiphenyl CAS No 92-67-1 N/A Benzidine CAS No 92-87-5 N/A 4-Chloro-O-Toluidine CAS No 95-69-2 N/A 2-Naphthylamine CAS No 91-59-8 N/A O-Aminoazotoluene CAS No 97-56-3 N/A 2-Amino-4-Nitrotoluene CAS No 99-55-8 N/A P-Chloraniline CAS No 106-47-8 N/A 2,4-Diamino-Anisole CAS No 615-05-4 N/A 4,4'-Diaminodiphenylmethane CAS No 101-77-9 N/A 3,3'-Dichlorobenzidine CAS No 91-94-1 N/A 3,3'-Dimethoxybenzidine CAS No 119-90-4 N/A 3,3'-Dimethylbenzidine CAS No 119-93-7 N/A 4,4'-Diamino-3,3'-Dimethylphenyl Methane CAS No838-88-0

N/A

P-Cresidine CAS No 120-71-8 N/A 4,4'-Methylene-Bis-(2-Chloraniline) CAS No 101-14-4 N/A 4,4'-Thiodianiline CAS No 139-65-1 N/A O-Toluidine CAS No 95-53-4 N/A 2,4'-Toluylenediamine CAS No 95-80-7 N/A 2,4,5-Trimethylaniline CAS No 137-17-7 N/A O-Anisidine CAS No 94-04-0 N/A P-Aminoazobenzene CAS No 60-09-3 N/A 2,4-Dimethylbenzeneamine CAS 95-68-1 N/A 2,6-Dimethylbenzeneamine CAS 87-62-7 N/A

ADDITIONAL INFORMATION / NOTES Note 1 – ‘UoM’ denotes estimated Uncertainty of Measurement for stated test results. This uncertainty value is

based on a standard uncertainty multiplied by a coverage factor k = 2, which provides for a confidence level of

approximately 95%

Note 2 – Estimated uncertainty of measurement applied at point of test (e.g. to applied force or to tolerance limits)

to ensure product meets requirements of the standard

Note 3 – Test result(s) would meet the requirements of EN 388: 2003 for a level 5 if uncertainty of measurement

was not taken into account. However, if uncertainty (as stated in UoM column) is applied, this result may be

considered to fulfil the requirements of a level 4 only.




ANNEX A:

Photo-documentation

General Appearance of the EU for Risks

Photo 1

※※※※※END OF REPORT※※※※

SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO: … · SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO:...

Documents

Transcript of SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO: … · SHENZHEN POCE TECHNOLOGY CO., LTD. REPORT NO:...