SHAFTWALL C-H STUDFIRE RATING

ENGINEERING CATALOG

1-800-275-2279

C-H Studs & J-Track for Shaft Wall Construction

1-800-275-2279

Design Number: Minimum "C-H" Shaped Stud Size: Min. Thickness: Fire Resistance RatingU428 2-1/2" C-H Shaped studs, 1-1/2" wide 25 GA. 2 hourU429 2-1/2" C-H Shaped studs, 1-1/2" wide 25 GA. 2 hourU438 2 1/2" C-H Shaped studs, 1 1/2" wide 25 GA. * 2 hourU459 2 1/2" C-H Shaped studs, 1 1/2" wide 20 GA. 2 hourU467 2 1/2" C-H Shaped studs, 1 1/2" wide 25 GA. * 2 hourU469 2 1/2" C-H Shaped studs, 1 1/2" wide 25 GA. * 1 hourU492 4" C-H Shaped studs, 1 1/2" wide 25 GA. 2 hour

* - Minimum thickness depends on manufacturer of drywall.

Steeler Part #: Stud Dimensions: Gauge:

0250H150-027 2 1/2" x 1 1/2" deep 220250H150-030 2 1/2" x 1 1/2" deep 20DW0250H150-033 2 1/2" x 1 1/2" deep 20

0400H150-027 4" x 1 1/2" deep 220400H150-030 4" x 1 1/2" deep 20DW0400H150-033 4" x 1 1/2" deep 20

0600H150-027 6" x 1 1/2" deep 220600H150-030 6" x 1 1/2" deep 20DW0600H150-033 6" x 1 1/2" deep 20

Steeler and Steeler, Inc. are registered trademarks of Steeler, Inc. Copyright 2007 Steeler Inc. All Rights Reserved. July 27, 2011

Phone Number: (800) 275-2279; Fax (206) 725-1300. 10023 Martin Luther King Jr. Way South, Seattle, WA 98178

www.steeler.com e-mail: engineering@steeler.com

UL Technical Services, Conformity Assessment Services (CAS) Phone Number: (847) 272-8800 ext. 42364; Fax (847) 509-6292.

http://www.ul.com/contact.html

David Jeter, Steeler Engineer.

3) All wallboard sizes specified in each system design must bear a UL classification marking.4) Note specific manufacturers standard gauge (MSG) and stud length (floor to ceiling) requirements in each system design.5) Note "J" shaped floor and ceiling runners (J Track) require unequal leg lengths of 1 in. and 2 in. and manufacturers standard gauge (MSG) requirements may vary by system design.

References:

STEELER ® INC. Shaft Walls

STEELER ® C-H Studs can be used in the Shaft Wall construction as listed below in the following UL Design Numbers. UL Certifications are available at www.ul.com, or copies

are available upon request.

1) Steeler C-H Studs conform to the manufacturers standard gauge (MSG), shape, and section property specifications listed in each UL/USG system design and Fire Resistance Rating and are therefore acceptable for use with listed wallboard gypsum products bearing the UL classification marking.2) The 2 1/2" web X 1 1/2" flange dimension for C-H Studs is a minimum requirement and larger sizes, i.e.; 4" and 6" (studs) are permitted system stud sizes under any UL certification.

0250H150-024 2 1/2" x 1 1/2" deep EU 30

0400H150-024 4" x 1 1/2" deep EU 30

0600H150-024 6" x 1 1/2" deep EU 30

STEELER ® INC. Shaft Walls C-H Studs & J-Track for Shaft Wall Construction

1-800-275-2279

J-Track Part #: Web (A): Flange (B): Stiffener flange (C): Thickness:0250J100 2 1/2" 2 1/4" 1" 18, 27, 30, 33 mils0250J200 2 1/2" 2 1/4" 2" 18, 27, 30, 33 mils0400J100 4" 2 1/4" 1" 18, 27, 30, 33 mils0400J200 4" 2 1/4" 2" 18, 27, 30, 33 mils0600J100 6" 2 1/4" 1" 18, 27, 30, 33 mils0600J200 6" 2 1/4" 2" 18, 27, 30, 33 mils

*Part # Notes: Desired thickness of J-Track is indicated by appending mil thickness to part # listed above.

Steeler and Steeler, Inc. are registered trademarks of Steeler, Inc. Copyright 2007 Steeler, Inc. All Rights Reserved.

Steeler Inc.'s Engineered C-H Stud and J-Track are an economical solution to Shaft Wall Systems. Steeler C-H shaped studs are shaped by cold-formed shaping of the steel, which increases the strength

of the C-H stud. Other competing Shaft Wall Systems use knock out tabs to hold the shaft liner in place, however these knock-out tabs reduce the strength of those Shaft Wall studs and reduce the limiting wall heights of such walls. Steeler C-H are safer and easier to work with because the edges

(except for one lip return) are hemmed and there are no sharp knock out tabs to worry about.

6" C-H Stud Diagram J - Track Diagram

Steeler J-Track is manufactured from steel meeting the requirements of ASTM C653-02a or equal, Grade 33 (fy=33KSI).

J-Track is used for top, bottom, and end of wall track in construction of Shaft Wall Systems.

Steeler J-Track is available with webs of 2 1/2", 4", and 6". The long flange is 2 1/4" and short flange (stiffener) is available with 1" and 2" flanges.

1

STEELER ® INC. J-Track PropertiesJ-Track for Shaft Wall Construction

1-800-275-2279

Web Flange Stiffener Design RadiusA B C T R May Vax Ιye Sye Aein in in in in kip-in kips in4 in3 in2

250 J100-18 2.622 2.25 1.00 0.0188 0.0843 0.8999 0.247 0.0679 0.0455 0.0366250 J100-27 2.636 2.25 1.00 0.0283 0.0796 1.5439 0.685 0.1123 0.0781 0.0754250 J100-30 2.641 2.25 1.00 0.0312 0.0782 1.7646 0.832 0.1270 0.0893 0.0896250 J100-33 2.646 2.25 1.00 0.0346 0.0764 2.0359 1.023 0.1448 0.1030 0.1073

250 J200-18 2.622 2.25 2.00 0.0188 0.0843 0.8674 0.247 0.0792 0.0439 0.0369250 J200-27 2.636 2.25 2.00 0.0283 0.0796 1.7070 0.685 0.1442 0.0864 0.0765250 J200-30 2.641 2.25 2.00 0.0312 0.0782 1.9498 0.832 0.1634 0.0987 0.0910250 J200-33 2.646 2.25 2.00 0.0346 0.0764 2.2482 1.023 0.1866 0.1138 0.1092

400 J100-18 4.122 2.25 1.00 0.0188 0.0843 1.4271 0.152 0.1807 0.0722 0.0373400 J100-27 4.136 2.25 1.00 0.0283 0.0796 3.0404 0.518 0.3395 0.1539 0.0780400 J100-30 4.141 2.25 1.00 0.0312 0.0782 3.4461 0.695 0.3818 0.1744 0.0930400 J100-33 4.146 2.25 1.00 0.0346 0.0764 3.9409 0.948 0.4326 0.1994 0.1121

400 J200-18 4.122 2.25 2.00 0.0188 0.0843 1.4113 0.152 0.2075 0.0714 0.0376400 J200-27 4.136 2.25 2.00 0.0283 0.0796 3.0457 0.518 0.4004 0.1541 0.0791400 J200-30 4.141 2.25 2.00 0.0312 0.0782 3.6946 0.695 0.4703 0.1870 0.0945400 J200-33 4.146 2.25 2.00 0.0346 0.0764 4.3807 0.948 0.5456 0.2217 0.1140

600 J100-18 6.122 2.25 1.00 0.0188 0.0843 2.1186 0.100 0.4251 0.1072 0.0377600 J100-27 6.136 2.25 1.00 0.0283 0.0796 4.6117 0.342 0.8177 0.2334 0.0794600 J100-30 6.141 2.25 1.00 0.0312 0.0782 5.6255 0.459 0.9610 0.2847 0.0949600 J100-33 6.146 2.25 1.00 0.0346 0.0764 7.0098 0.626 1.1457 0.3547 0.1146

600 J200-18 6.122 2.25 2.00 0.0188 0.0843 2.1381 0.100 0.4798 0.1082 0.0380600 J200-27 6.136 2.25 2.00 0.0283 0.0796 4.5505 0.342 0.9255 0.2303 0.0805600 J200-30 6.141 2.25 2.00 0.0312 0.0782 5.4838 0.459 1.0839 0.2775 0.0963600 J200-33 6.146 2.25 2.00 0.0346 0.0764 6.7098 0.626 1.2830 0.3396 0.1166

Steeler and Steeler, Inc. are registered trademarks of Steeler, Inc. Copyright 2003 Steeler, Inc. All Rights Reserved.

Web Depth 6.00" Lip 2.00"

Allowable Moment, Shear and Effective Section Properties

Web Depth 2.50" Lip 1.00"

Web Depth 6.00" Lip 1.00"

Web Depth 4.00" Lip 1.00"

Web Depth 2.50" Lip 2.00"

Web Depth 4.00" Lip 2.00"

SectionFy = 33 ksi, Fu = 45 ksi

2

3

4

5

6

7

8

9

10

11

12

13

14

15

S_NS– 3/5/2012 Steeler, Inc.

Potential LEED® Points for Steeler Metal Framing

Corporate Sales

P 800.275.2279

marketing@steeler.com

Engineering Services

P 206.760.7100

engineering@steeler.com

11 Potential Points

Steeler Inc. is stepping up to the environmental challenges of today and contributing to future generations by supporting green build-

ing with green products. Steeler Inc. framing systems and products are the environmentally responsible choice. Below is a list of

LEED Credits that can apply to your project and to sustainability of the built environment. Let us help you do your part by specifying

Steeler framing and products.

LEED Credit MR 2

Construction Waste Management (1-2 points) Steeler framing products are manufactured from cold-formed

steel (CFS). CFS is 100% recyclable and therefore contributes

significantly to LEED Credit MR 2. The specific contribution

amounts will vary depending on the project and construction

decisions.

LEED Credit MR 4

Recycled Content (1-2 points) Steeler framing products contain a minimum of 26% post-

consumer and 7% pre-consumer recycled steel content for a

minimum of 33% recyclable. Recycled content of materials

contributes to LEED Credits MR 4. If notified in advance, Steeler

can order steel containing higher percentages of recycled content

to meet your specific project needs. Contact Steeler technical

services prior to ordering so we can help support your project

goals.

LEED Credit MR 5

Regional Materials (1-2 points) Steeler framing products contain a large percentage of locally

sourced materials and can contribute to LEED Credits MR 5.

Materials contributing to these credits must be extracted,

harvested, or recovered, and manufactured within a 500 mile

radius OR <500 miles of total travel distance using a weighted

mileage contribution depending on the means of travel.

LEED Credit ID 1

Innovation in Design (1-2 points) Steeler framing can contribute to LEED Credits ID 1 through

Path 2 and exemplary performance for Recycled Content and/or

Regional Materials. Credit for exemplary performance may

require steel with a higher than average recycled content.

Contact Steeler technical services prior to ordering so we can

support your project goals by ordering highly recycled steel.

LEED Credit RP 1

Regional Priority (1-3 points) Steeler framing can contribute to LEED Credits RP 1 by

addressing geographic-specific environmental priorities. If your

project area has defined any of the above LEED Credits as a

regional priority, then your project qualifies for one credit per

priority met. Verify your project’s regional priority credits at the

U.S. Green Building Council (USGBC) website, www.usgbc.org

Steeler Plant Locations

• Seattle, WA • Newark, CA

Steeler Inc. supports the U.S. Green Building Council by retaining LEED knowledgeable professionals on staff. Steeler Inc. engineer-

ing services (206-760-7100) can assist you in documenting and applying LEED Certification Credits to your project. Let’s develop a

more sustainable building environment together!

*Denotes availability in zinc coating

Product Lines

FASTENERS Steeler Product Offerings

Super Steelers™*

Hi-Lo Super Steelers™

Super Woodies™*

Super Framer*

Super Lathers*

Super Hex Framers*

Super Laminating

Flat Stock

Shaftwall Studs

J Track

Z-Furring Channel

Custom Brake Shapes

Steeler Slotted Studs™

Pony Wall Supports

TOOLS & ACCESSORIES Steeler Product Offerings

Bit Tips & Bit Tip Holders

Magnetic Nut Runners

Chop Saw Blades

DeWalt

Empire Levels

Kett Tool Company

ToolPro

Pacific Laser Systems

Wal-Board Tools

Ramset Fastening Systems

3M Construction Supplies

And more...

INTERIOR FINISHING & DRYWALL Steeler Product Offerings

Hanger Wire

U-Hank Tie Wire

Engineered Slide Clips

National Gypsum

The Steel Network

Knauf Insulation

Westpac Materials

Products from USG

Murco Wall Products

Award Metals Corner Beads

Trim-Tex Drywall Products

And more...

INTERIOR & EXTERIOR FRAMING

Steeler Manufactured Products

Steel Studs & Track

Smooth Products™

Slotted Track

Sound Resilient Channel

Furring Channel

Cold-Rolled Channel

Angle

Rust Resistant Screws

Drywall Drillers*

Cement Board Screws

Super Framing Drillers*

Wafer Head Drillers*

Super Hex Drillers*

And more...

Seattle Sacramento206-725-8500 916-483-3600

206-725-1100 FAX 916-483-3018 FAX

Tacoma Newark 253-572-8200 510-505-9595

253-572-8400 FAX 510-505-0200 FAX

Portland San Diego503-231-1100 619-527-1000

503 235 2908 FAX 619 527 1005 FAX

Phoenix623-848-0007

623 848 3055 FAX

Bakersfield661-399-3333

661 399 0004 FAX

10023 Martin Luther King Jr. Way SouthSeattle, WA 98178

(206) 725-2500 (206) 725-1700 FAX (800) 275-2279 Toll Free

509-928-5741 FAX

Spokane509-926-7403

Delta, B.C.604-940-1332

STEELER ® ICC-ES REPORT ESR-2054

604-940-1334 FAX 520-292-1037 FAX

Tucson520-690-0077

marketing@steeler.com www.steeler.com

503-235-2908 FAX 619-527-1005 FAX623-848-3055 FAX661-399-0004 FAX

Redmond425-869-5555

425-869-5557 FAX