SGI Confidential 5 - 1

Power Bay

SGI Confidential 5 - 2

Power Bay Front View

AC OK LED

DC OK LED

Alarm LED

Release Latch

Power Bay 1

Power Bay 0Power BayStatus LED

Power Bay Ethernet Port

Power Supply 1

Power Supply 2

Power Supply 3

Power Supply 4

The Power Bay supplies AC and DC to the major cabinet assemblies• A Power bay will always have two Rectifiers installed in slots PS1 and PS3• When the 3rd shelf is connected to a Power Bay, PS2 and PS4 must be installed• When the 5th shelf is added to a cabinet, a second Power Bay must be installed• When the 7th shelf is added to a Power Bay, PS2 and PS4 must be installed

SGI Confidential 5 - 3

Power Bay Rear View

Site PowerCord Drops(AC0 right side)(AC1 left side)

Circuit Breaker CB1

Circuit Breaker CB0

48vdc connector(DC0 left side)(DC1 right side)

Safety Ground Connector

4 ATS AC OutletsPBx-AT-1 left sidePBx-AT-4 right side

AC OutletsPBx-AC1-1 leftPBx-AC1-2 right

AC OutletsPBx-AC0-1 leftPBx-AC0-2 right

Power BayEthernet PortPBx-NIC

SGI Confidential 5 - 4

Power Bay Internal View (1 of 2)Personality Module: Thismodule is not a FRU, butit could be. There are 3types of modules basedon customer power.

Valere Power Inc. chassis is mounted in the front of theCopan chassis and interfaces the Copan wiring blocks.

Copan chassis and internalwiring to interface the personality module.

SGI Confidential 5 - 5

Power Bay Internal View (2 of 2)

Personality Module

SGI Confidential 5 - 6

RectifierThe rectifier is a hot pluggable FRU that converts site AC to AC and DC out.

The power bay only needs one rectifier installed to provide power to the components connected to it.

AC OK LED

DC OK LED

Alarm LED

Release Latch

SGI Confidential 5 - 7

Valere Power Inc. Web Interface (1 of 5) • Most info is passed to PSM GUI and that should be the primary tool to use• Valere interface is not accessible by PSM• You must connect a laptop directly to PB or an open port on the private network switch• A crossed Enet cable may be required• Set laptop to the same subnet of PB IP• Point browser to http://<PB IP>• Browser will auto-connect to port 22096• Access with standard login/password

Note: if the connection fails, your webbrowser or its version may not be supported. Try using an older version.

SGI Confidential 5 - 8

Valere Power Inc. Web Interface (2 of 5)

SGI Confidential 5 - 9

Valere Power Inc. Web Interface (3 of 5)

SGI Confidential5 -

10

Valere Power Inc. Web Interface (4 of 5)

SGI Confidential5 -

11

Valere Power Inc. Web Interface (5 of 5)

SGI Confidential5 -

12

Valere Power Inc. CLI (1 of 4)The power bay support a low-level command line interface. To access it, you telnet to the power bay. Login is Admin and the password is 5001. The power bay supportsonly one telnet session.

The CLI usage is as follows:

usage: verb object token [data]...

where: verb is get or set

• object is a category of tokens• token is an attribute name to be printed or set• data is the value used to set an object:token

Use 'get help help' or ‘set help help’ to get a list of objectsUse 'get <object> help' to get a list of tokens

To close a session type logout

If you are unable to access the power bay, you may have to run the/usr/local/copan/bin/setps script to assign the IP address. This scriptalso sets the login and password information.

SGI Confidential5 -

13

Valere Power Inc. CLI (2 of 4)

SGI Confidential5 -

14

Valere Power Inc. CLI (3 of 4)

SGI Confidential5 -

15

Valere Power Inc. CLI (4 of 4)

SGI Confidential5 -

16

Shelf Cabinet Power Bay DC Cabling6

Sh

elf

Cab

inet

8 S

hel

f C

abin

et

SGI Confidential5 -

17

Module Review QuestionsThis completes the Power Bay module. Answer the review questions before proceeding.

01. List the Power Bay FRU?02. Which Power Bay FRUs are hot pluggable?03. Why are rectifies installed in slots 1 and 3?04. What is the path and name of the script that assign IPs, login account , and passwords?05. What is the PB default login and password?06. How may shelves does a Power Bay support?07. What voltages does the Power Bay provide?08. How can you determine what the IP of the Power Bay is?09. Describe the ATS AC Outlet operation.10. Describe the non-ATS outlet operation11. Under what conditions are rectifiers installed in slots 2 and 4?

SGI Confidential5 -

18

Lab ProjectUsing applicable service documentation, you will be given 45 minutes to:

• Perform FRU replacement procedures• Observe LEDs under normal conditions• Access the Power Bay CLI and run various commands to determine state, status, temperature, voltages, etc….• Collect Power Bay information from the PSM GUI• View the setps script• Optionally, access the Valere web interface• Examine the PB portion of the PSM GUI to see what information is provided

SGI Confidential5 -

1919