Series MSC Sewage Chopper Pumps - A PumpMan Company · 2018-07-20 · Series MSC-Submersible...

7/21/2015 1

1144 Utica Ave, Brooklyn, NY 11203

Series MSC-Submersible Chopper Pumps

March 2015 New Catalogue Release

Bulletin 235A.1

Capacities to 450 GPM Heads to 65 Feet HP to 10 HP-1750 RPM

Series MSC Sewage Chopper Pumps

“Hardened tungsten carbide edged rotating impeller cutting and chopping against stationary chrome hardened suction plate reduce larger solids to mere particles and minimize downstream clogging that may occur when larger solids are pumped thru the impeller and into the piping system. “

7/21/2015 2




Bulletin 235A.1

Capacities to 450 GPM Heads to 65 Feet HP to 10 HP-1750 RPM

Introduction Federal Pump MSC Sewage Pumps provide for the lifting and disposal of sewage and sewage related fluids from retaining basins or concrete pits and are pumped to city waste disposal lines where these fluids cannot drain under gravity conditions alone. Typically located below grade, sewage pumps provide building owners the ability to design and locate restroom or other facilities below ground that are serviced by these sewage lift stations. In addition to their use in buildings, Federal Pump MSC chopper pumps are used in municipalities, larger residential buildings, below ground parking structures, industrial waste facilities and other areas where these sewage and waste particulates are collected and pumped to other locations. MSC chopper pumps differ from industry standard centrifugal sewage pumps that pass solids thru the impeller by actually shredding and grinding these solids within the pump; not allowing larger solids the opportunity to clog the pump, piping or disposal system. Hardened tungsten carbide edged rotating impeller cutting and chopping against stationary chrome hardened suction plate reduce larger solids to mere particles and prevent any downstream clogging that may occur when larger solids are pumped thru the impeller and into the piping system. Supported by heavy duty industrial shafts, bearings and increased motor insulation, the MSC pumps provide 20 starts per hour on/off cycle time capabilities and are supported with Federal Pump’s 3 Year Warranty.

Supported by Federal Pump’s SBS Simplex, Duplex and Triplex controls systems, the MSC sewage pump system supports 24 hour per day/7 days per week automatic operation for standard sewage pump services. Available in QD (Quick Disconnect Design) or free standing designs, the MSC product offering provides the end user with trouble free operation when designed, installed and maintained properly.



Bulletin 235A.1 1144 Utica Ave, Brooklyn, NY 11203

Neoprene power cable sheath for temperatures to 80 degree C (170 degree F)

Double inside mechanical seals with silicon carbide faces for extended seal life with nitrile-buna elastomer.

Double shielded permanently lubricated high temperature C3 ball bearings rated for B-10 bearing life of 60,000 hours.

Submersible air-filled motor copper wound-Class B insulation (available in Class F for higher temperature requirements)

Standard product provides 20 starts per hour.

Oil bath seal housing provides optimum seal lubrication and extended seal life and keeps mechanical seal away from pumped media.

Innovative triple protection motor/cable ends sealed with epoxy resin or molded rubber with built-in power cord strain relief. All units include anti-wicking block to eliminate water intrusion into the motor.

Built-in thermal motor protection prevents motor failure due to overloading, single phasing (for three phase units) or accidental extended run-dry conditions.

Sintered tungsten carbide tipped cast iron impeller rotating against high chromium cast iron field replaceable and adjustable cutter- Brinell Hardness factor of 550- plate/suction cover reduce solids to shredded particles.

(Optional) Seal failure protection senses water intrusion into seal area with auto pump shut down and alarm condition.

Stainless Steel exposed fasteners.

Rugged cast iron pump case provides for metal to metal guide rail connections where pump and discharge mating connects are sealed tight for optimum performance.

7/21/2015 3


Component Description Material Composition Material Designation

1 Pump Casing Cast Iron A-48 Class 35

2 Impeller Cast Iron A48 Class 35

3 Impeller Tip Sintered Metal Edged Tungsten Carbide

4 Suction Cover Chrome Alloy cast Iron A532 Class 3 Type A

5 Mechanical Seal Silicon carbide Seal Faces

6 Motor Bracket Cast Iron A-48 Class 30

7 Power Cable Plastic Neoprene

8 Upper Bearing Thrust Bearing Steel-Ball Bearing

9 Lower Bearing Radial Bearing Steel-Ball Bearing

10 Pump Shaft Stainless Steel AISI 403

11 Lift Lug Bolt Steel A283 Grade D




Key Pump Components

11

6

7

10

5

1

2

4 3

8

9

7/21/2015 4

MSC-4C-10-2 10




Bulletin 235A.1

Pump Performance Data Series: MSC Chopper Pumps

Item Description

Discharge Sizes 2”, 3” & 4”

HP Range 1 thru 10 HP

Performance Range

50-450 GPM

Maximum Water Temperature

104 Degree F Optional: 170 Degree F

Casing ASTM 48 Class 35 Cast Iron

Impeller ASTM 48 Class 35 Cast Iron –Tungsten Carbide Edged Impeller

Cutter Plate High Chromium Cast Iron 550 Brinell Hardness

Shaft 400 Series Stainless Steel

Motor Frame ASTM 48 Class 30 Cast Iron

Fasteners 304 Stainless Steel Optional: 316 Stainless Steel

Mechanical seals Silicon Carbide/ Nitril Buna Elastomer Optional: Viton (CE-14) Elastomer

Bearings Pre-Lubricated-Double Shielded

Motor Type Air Filled Class B Insulation (Option for Class F-Higher Temperature)

Motor Operating Performance Amperage (average)

HP RPM 220V 230V 440V 460V 480V

1 3600 3.4 3.4 1.7 1.7 1.6

2 3600 6.3 6.1 3.2 3.1 2.9

3 1800 8.8 8.6 4.4 4.4 4.3

5 1800 14.5 14.1 7.3 7.1 7.0

7.5 1800 20 19.2 10.0 9.6 9.2

10 1800 29.4 28.0 14.6 14.0 13.5

Submersible MSC Cutter Pumps can be provided with optional accessory equipment including: • Sewage/Sump basin covers and frames. • Float switches for automatic operation. • Submersible level transducers for automatic operation and

level diagnostics. • Control panels with automatic system controls and

programmable logic controllers. • High level alarms or other alarm conditions. • Guide rail or free standing type designed pumps. • Fiberglass basins and accessories. • Factory assembled and tested unit with basin, pumps, valves

and controls-preassembled and wired.

7/21/2015 5

Notes: 1. Motors designed for 20 starts per hour. Level devices and pit depths should be designed to maintain 10-12 starts per hours at maximum 104 degree F for typical sewage pump applications. 2. Float devices require 8-12 “ of water level differential from low float(off) to high float(on) position. Basins should be designed to accommodate float level differential. 3. High water alarm float (on level) should be designed to activate at 6” below bottom of invert to prevent any fluids backing into the supply lines. Float switch tilt travel of 12” should be considered. 4. For higher temperature applications (above 104 degree F) contact factory for special motor insulation, special float materials and special accessories that may be required to sustain operation in higher temperature settings. 5. Most fiberglass basins limit temperatures to less than 120 degree F. For temperatures in excess of 120 degree F where fiberglass basins are required, contact the factory for special assistance.




Fully automatic “Quick Disconnect” sewage pump system designed for ease in installation and future pump maintenance. Available in factory assembled systems or shipped loose for field assembly with fiberglass basins and “gas tight” covers. The MSC-QD provides a formidable sewage ejector system combining technological material advancements with grinding and shearing action reducing sewage waste to shredded particles.

Guide rail “QD” system allows pumps to be installed or removed by guiding the pump up and down the installed guide rails and not requiring bolted connections to the discharge piping. Tungsten carbide edged impellers rotating against hardened chrome plates grind and shear sewage waste solids to particle sizes. Complete set of “QD” accessories including lifting chains, guide rails, covers, frames, basins and “gas tight” lids , floats and associated control panel or fully integrated packaged systems are available based upon system requirements and specifications.

7/21/2015 6




Components provided for field installation or factory assembled for ease and speed in installation are available. External piping from pump discharge to system are provided for in the field by the installing contractor.

Typical installation shown with fiberglass basin (standard sizes from 24” to 72” diameter) with steel base shown for mounting base elbows to fiberglass basin floor. Installation shows hinged aluminum cover (available in steel diamond plate or other materials). Installation figure shows overhead hoist for lifting and installing quick disconnect type pumps.

Installation shown with Federal Pump Series SBS float control system for automatic operation.

7/21/2015 7

TDH (feet)

50 GPM

75 GPM

100 GPM

125 GPM

150 GPM

175 GPM

20 MSC-2C 1HP

3600RPM

MSC-2C 1HP

3600RPM

MSC-3C 2HP

3600 RPM

MSC-3C 2HP

3600 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

25 MSC-3C 2HP

3600RPM

MSC-3C 2HP

3600RPM

MSC-3C 2HP

3600RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

30 MSC-3C 2HP

3600RPM

MSC-3C 2HP

3600RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 5HP

1800RPM

35 MSC-3C 2HP

3600RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

40 MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

45 MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

50 MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

55 MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

MSC-4C 10HP

1800RPM

MSC-4C 10HP

1800RPM

MSC-4C 10HP

1800RPM

MSC Product Selection Chart* Model Number- HP- RPM




Bulletin 235A.1

Quick Selection Tables for Flow Rates to 175 GPM (Refer to attached table for flow rates to 450GPM)

*Note: Refer to pump performance curve for pump operation over its entire range. Several models available in special trim sizes for reduced HP requirements.

MSC-4C-3-QD

Pump Series (MSC-Cutter/Chopper)

Discharge Size Motor HP Quick Disconnect Design

7/21/2015 8

MSC Product Selection Chart* Model Number- HP- RPM




Bulletin 235A.1

Quick Selection Tables for Flow Rates to 450 GPM

MSC-4C-3-QD

Pump Series (MSC-Cutter/Chopper)

Discharge Size Motor HP Quick Disconnect Design

TDH (feet)

200 GPM

225 GPM

250 GPM

300 GPM

350 GPM

400 GPM

450 GPM

20 MSC-4C 3HP

1800 RPM

MSC-4C 3HP

1800 RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

25 MSC-4C 3HP

1800 RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

30 MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

35 MSC-4C 5HP

1800RPM

MSC-4C 5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

40 MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

45 MSC-4C 7.5HP

1800RPM

MSC-4C 10HP

1800RPM

50 MSC-4C 10HP

1800RPM

7/21/2015 9

*Note: Refer to pump performance curve for pump operation over its entire range. Several models available in special trim sizes for reduced HP requirements.




Bulletin 235A.1

7/21/2015 10

40 35 30 25 20 15 10 5

0 10 20 30 40 50 60 70 80 90 100 0

Head Ft

Capacity: US Gallons Per Minute

30 25 20 15 10

Eff %

Brake HorsePower

1.5 1.0 0.95 0.90 0.85

Model: MSC-2C-1 RPM: 3450 Curve No: CFP10 A Type: Cutter Impeller Release: 3.2015

BHP

Model No Curve No RPM Motor HP

MSC-2C-1-2 CFP-10A 3450 1

2” Discharge-Cutter Blade Design Sewage Pump

Brake-HP




Bulletin 235A.1

7/21/2015 11

80 70 60 50 40 30 20 10

0 20 40 60 80 100 120 140 160 180 200 0

Head Ft


50 40 30 20

Eff %

Brake HorsePower

3.5 1.8 1.6 1.4


BHP


MSC-3C-2-2 CFP-20A 3450 2


Brake-HP




Bulletin 235A.1

7/21/2015 12

80 70 60 50 40 30 20 10

0 25 50 75 100 125 150 175 200 225 250 275 300 0

Head Ft


50 40 30 20

Eff %

Brake HorsePower

3.5 3 2.5 2 1.5


BHP


MSC-4C-3-4 CFP-30A 1750 3


Brake-HP




Bulletin 235A.1

7/21/2015 13

80 70 60 50 40 30 20 10

0 50 100 150 200 250 300 350 400 450 500 550 600 650 0

Head Ft


50 40 30 20

Eff %

Brake HorsePower

6 5 4 3 2


BHP


MSC-4C-5-4 CFP-50A 1750 5


Brake-HP




Bulletin 235A.1

7/21/2015 14

80 70 60 50 40 30 20 10

0 50 100 150 200 250 300 350 400 450 500 550 600 650 0

Head Ft


50 40 30 20

Eff %

Brake HorsePower

8 7 6 5 4

Model: MSC-4C-7.5A RPM: 1750 Curve No: CFP7.5 A Type: Cutter Impeller Release: 3.2015

BHP


MSC-4C-7.5-4 CFP-47.5 1750 7.5


Brake-HP




Bulletin 235A.1

7/21/2015 15

80 70 60 50 40 30 20 10

0 50 100 150 200 250 300 350 400 450 500 550 600 650 0

Head Ft


50 40 30 20

Eff %

Brake HorsePower

9 8 7 6 5

Model: MSC-4C-10 RPM: 1750 Curve No: CFP 10 Type: Cutter Impeller Release: 3.2015

BHP


MSC-4C-10.4 CFP-410 1750 10


Brake-HP




Bulletin 235A.1

MSC-QD Dimensional Data

Discharge Model HP RPM A B C D E F G

2 MSC-2C-1-2 1 3600 17 5/16 3 1/8 4 3/4 6 5/16 4 5/16 7 7/8 9 3/16

3 MSC-3C-2-2 2 3600 21 3 3/8 6 11/16 8 11/16 6 1/8 9 13/16 9 5/16

4 MSC-4C-3-4 3 1800 24 13/16 4 3/4 6 11/16 8 11/16 6 1/8 9 13/16 11 7/16

4 MSC-4C-5-4 5 1800 27 9/16 4 3/4 6 11/16 8 11/16 6 1/8 9 13/16 11 7/16

4 MSC-4C-7.5-4 7.5 1800 35 11/16 4 5/8 7 7/8 9 13/16 7 7/8 11 7/16 11 1/4

4 MSC-4C-10-4 10 1800 36 1/2 4 5/8 7 7/8 9 13/16 7 7/8 11 7/16 11 1/4

Discharge Model HP RPM H J K L M N O Weight

2 MSC-2C-1-2 1 3600 8 13/16 2 1 15/16 7 5/8 3/8 1 2 3/4 98

3 MSC-3C-2-2 2 3600 8 7/8 3 2 3/8 8 7/8 9/16 1 1/4 3 1/8 128

4 MSC-4C-3-4 3 1800 8 7/8 4 2 3/8 10 5/8 9/16 1 1/4 3 1/8 186

4 MSC-4C-5-4 5 1800 8 7/8 4 2 3/8 10 5/8 9/16 1 1/4 3 1/8 222

4 MSC-4C-7.5-4 7.5 1800 10 7/8 4 3 3/4 13 3/4 2 3 5/16 326

4 MSC-4C-10-4 10 1800 10 7/8 4 3 3/4 13 3/4 2 3 5/16 358

A

B

C D

E

F

G

H

J Discharge Flange

K L

(4) M Diam Holes

N (Diameter)

O

7/21/2015 16




Bulletin 235A.1

Upper Guide Bar Bracket

Discharge Model HP RPM A B D E F G H J

2 MSC-2C-1-2 1 3600 9 13/16 1 15/16 7 5/16 2 3/4 3/8 1 2 3/16 3/8

3 MSC-3C-2-2 2 3600 11 5/16 2 3/8 7 11/16 3 1/8 3/8 1 2 3/16 1 1/8

4 MSC-4C-3-4 3 1800 11 5/16 2 3/8 7 11/16 3 1/8 3/8 1 2 3/16 1 1/8

4 MSC-4C-5-4 5 1800 11 5/16 2 3/8 7 11/16 3 1/8 3/8 1 2 3/16 1 1/8

4 MSC-4C-7.5-4 7.5 1800 14 1/4 3 3/4 9 5/8 3 15/16 1/2 1 3/16 2 5/8 2 5/16

4 MSC-4C-10-4 10 1800 14 1/4 3 3/4 9 5/8 3 15/16 1/2 1 3/16 2 5/8 2 5/16

A

B

D

E

(2) F Holes

G

H

J

Dimensions in inches

7/21/2015 17

Upper Guide Bar Bracket (3) 1. Locate guide bars into lower guide bar bracket (integral to cast

iron elbow mounted in basin floor.) 2. Insert guide bars into lower base elbow extending to top of

basin. 3. Insert Upper Guide Bar Bracket into guide bars and then bolt

upper guide bar bracket in place. 4. Pump mounted guide bracket slides up and down guide rails to

install pump to base elbow and to lift pump from pit using guide bar brackets as positioning devices.



Bulletin 235A.1

Discharge Model HP RPM A B C D E F G J W Weight (Lbs.)

2 MSC-2C-1-2 1 3600 8 7/8 4 7/8 16 4 7/8 4 7/8 7 11/16 5 3/4 16 1/4 2 93

3 MSC-3C-2-2 2 3600 10 1/2 4 7/8 17 1/2 4 7/8 4 7/8 9 3/16 7 1/2 19 3 120

4 MSC-4C-3-4 3 1800 13 1/4 6 1/2 23 1/2 6 5/8 6 1/2 12 15/16 8 7/8 24 1/4 4 180

4 MSC-4C-5-4 5 1800 13 1/4 6 1/4 23 11/16 6 7/8 6 1/2 13 1/8 9 1/4 27 3/16 4 215

4 MSC-4C-7.5-4 7.5 1800 15 1/4 7 5/8 27 1/16 8 7 3/4 14 5/8 13 1/4 35 3/4 4 320

4 MSC-4C-10-4 10 1800 15 1/4 7 5/8 27 1/16 8 7 3/4 14 5/8 13 1/4 36 9/16 4 350

MSC-Free Standing Dimensional Data


C A B

D

E

F

W (Discharge)

G

J

All dimensions in inches

7/21/2015 18

Mounting legs are for support only and may vary in shape and design based upon pump model selected. Support legs are not to be bolted to basin/pit bottom. Legs shown in dimensional print are for illustration purposes only. For exact details of support legs by model, contact Federal Pump for detailed dimensions. Dimensions subject to change without notice.

(Minimum Water Level)




ON

OFF

12”

SBS Liquid Level Float Control Above Ground Float Control System

7/16” 1 ¼”

Float wire compression fittings

NEMA 4 Power Junction Box Float Support Detail

A

B

C

D E

Item Description

A Metal weight maintains float position

B Plastic mechanical float switch –floats on water surface

C ¾” galvanized steel threaded rod assembly

D Threaded eye hook- holds float wire in place

E ¾” threaded “T”-part of SBS float assembly

F Allow 12” level for on/off operation

F

Varies, based upon basin or pit depth

Pumps off

Lead On

High Water

Lag On

10 1/2” Diameter

Connect to Wall Mounted Duplex/Triplex SBS Controller

(4) 1/2” Holes on 9” Bolt Circle (Note: 8” Cover Plate Opening)

Notes: 1. Allow 8” diameter opening

in cover for in installation of SBS float system.

2. Ensure gasket is installed between SBS plate and basin cover.

3. Submersible motor power cables will exit pit or basin cover from another point (refer to cover details for those locations).

4. NEMA 4 junction box shown is for float switches and power cable connections. Where possible, wire those float and pump power cables directly to the level control panel and not the junction box.

5. SBS eye hook (D) and elbow connections ( E) preset at the factory. Coordinate those with basin depth.

6. Contractor to set SBS system in place, draw float wires through eye hooks and through compression fittings and then wire to junction box or directly to control panel (refer to attached drawings for control panel).

7/21/2015 19

8”




SBS Liquid Level Float Control Above Ground Float Control System

Lowest float (A) is N/O and closes as liquid level tilts switch upward. Lead Pump (B) float is N/O and closes on liquid level tilt. Lag Pump (C) is N/O and closes upon liquid level tilt. High water float (D) is N/O and closes upon liquid level tilt. Pump operation and high water alarm requires lowest float (A) to be tilted upward to connect appropriate circuitry for pump and/or alarm conditions.

A

B

C

D

7/21/2015 20

.




A

B

C

D

Type SBS submers-a-bulb controller

H-O-A H-O-A

Pump-1 Pump-2

Pump On Pump On

Seal Fail Seal Fail

High Water Level Silence Button

Alarm Horn

24”

32”

Available in NEMA 1,12,4,4X or other enclosure styles as may be required for the installation. Simplex (single pump), Duplex ( 2 pump), Triplex (3 pump) control systems available.

Above control panel is sample only and will vary based upon options, enclosure style or other specifications.

7/21/2015 21

Control Panel shown include several options and should be reviewed in detail prior to order. Dimensions may vary based upon enclosure type, options requested and specification requirements. SBS Float Control system includes: Floats and support frame, mounting bracket, float wire compression fittings, NEMA 4 junction box, simplex, duplex or triplex control panel (for wall mounting) and provided in enclosure specified (or ordered)




Bulletin 235A.1

Sample: Duplex SBS Control Panel with fused disconnect switches and alarm indicators shown in above diagram. Wiring Diagram shown is sample only and subject to required options, additional dry contacts for link to property management systems, other power disconnect devices and options that may or may not be shown in the above diagram. The NEMA 4 junction box shown in previous data sheets is provided with the SBS control system as standard . Where possible and practical, motor power cables and float control wiring should be connected directly to the control panel and not the junction box. Contact Federal Pump when high temperatures are involved to ensure the pump, power cables, floats and other accessory fittings have been provided for properly.

7/21/2015 22




Basin ID A

Cover OD B

Bolt Circle C

Cover Thickness D

Door Width E

Door Length F

Clear Opening G

Clear Opening H

30 X 30 34 X 34 32.5 X 32.5 0.25 16 22 14 20

36 X 36 40 X 40 38.5 X 38.5 0.25 18 28 16 26

42 X 42 46 X 46 44.5 X 44.5 0.25 20 32 18 30

48 X 48 54 X 54 51 X 51 0.25 26 36 24 34

60 X 60 66 X 66 63 X 63 0.25 32 44 30 42

72 X 72 78 X 78 75 X 75 0.25 36 48 34 46

Duplex Square Pit/Basin Aluminum Cover with Hinge Door

SBS Float Plate

.

.

B A E G

H

F

D

(8) 9/16” holes on C Bolt Circle

3” Vent

Pump Connections

Note: Cover bolts directly to concrete floor or fiberglass basin (no frame required) and suitable for foot traffic. For higher loading requirements, contact Federal Pump for additional details. Specify vent size and pump discharge piping size when specifying or ordering aluminum cover. Specify “gas-tight” design for all indoor installations.

7/21/2015 23




Duplex Round Pit/Basin Aluminum Cover with Hinge Door

Note: Cover bolts directly to concrete floor or fiberglass basin (no frame required) and suitable for foot traffic. For higher loading requirements, contact Federal Pump for additional details. Specify vent size and pump discharge piping size when specifying or ordering aluminum cover. Specify “gas-tight” design for all indoor installations.

Basin ID A

Cover OD B

Bolt Circle C

Cover Thickness

D

Door Width

E

Door Length

F

Clear Opening- G

Clear Opening- H

30 34 32.5 0.25 16 22 14 20

36 40 38.5 0.25 18 28 16 26

42 46 44.5 0.25 20 32 18 30

48 54 51 0.25 26 36 24 34

60 66 63 0.25 32 44 30 42

72 78 75 0.25 36 48 34 46

24

B

A

. C

D

. (6) 9/16” Holes .

H

F

E G

7/21/2015

3” Vent




Note: When specifying fiberglass basins or designing concrete pits, useable water volume needs to be considered to minimize pump start/stop cycles and ensure float swing (12”) are taken into consideration for proper operation. Ensure basin designs (depth and diameter) are adequately sized for system flow requirements and for proper fluid storage to maintain minimum on/off pump cycling.

25

7/21/2015

Pump Model Simplex Minimum Basin

Diam.

Duplex Minimum Basin

Diam.

MSC-2C-1-2 24” 36”

MSC-3C-2-2 24 42”

MSC-4C-3-4 36” 48”

MSC-4C-5-4 36” 48”

MSC-4C-7.5-4 42” 54”

MSC-4C-10-4 42” 54”

MSN- Basin Selection

Round Basins/Concrete Pits

Basin Capacity (6’-0’ Deep)

Diameter Capacity

24” 118 Gallons

30” 184 Gallons

36” 264 Gallons

42” 360 Gallons

48” 470 Gallons

60” 735 Gallons

72” 1269 Gallons

Useable water volume area

Pump “off” area

Depth for invert location area




7/21/2015

Pumps Furnish and install where shown in the plans a Federal Pump model MSC-QD quick disconnect submersible cutter duplex sewage pump system with each pump flow (GPM) and TDH (Feet) rated as shown on the plans. Casing, impeller, discharge elbow, and motor frame shall be manufactured from gray cast iron with each pump having a field adjustable and or replaceable, high chrome iron cutter plate. Internal and external surfaces coming into contact with the fluid shall be protected by a fused polymer coating. All exposed fasteners shall be stainless steel. All units shall be furnished with a base mounted discharge elbow with discharge flange connections as shown in the plans. Pump to elbow connection shall be metal to metal. Impellers shall be of the single or two-vane semi-open solids handling design equipped with tungsten carbide vane tip and shall be slip fit to the shaft and key driven. All units shall be furnished with a dual inside mechanical shaft seal located completely out of the fluid, running in a separate oil filled chamber and further protected by an exclusionary oil seal located between the bottom seal faces and the fluid being pumped. Pumps shall be provided with silicon carbide versus silicon carbide upper and lower mechanical seal faces. Mechanical seal hardware shall be stainless steel. Motors Motors will be air-filled and provided with 20 feet of submersible power cable and shall be NEMA MG-1, design type B equivalent and rated at full load amps. Motor(s) shall have a 1.15 service factor and shall be rated for 20 starts per hour. Motor(s) shall be air filled, copper wound, class E or F insulated with built in thermal and over current protection for each winding. Motor shaft shall be 420 stainless steel and shall be supported by two permanently lubricated, high temperature ball bearings, with a B-10 life rating at best efficiency point of 60,000 hours. The bottom bearing on pumps rated 7.5 HP and below shall be a single row, double shielded, C3, deep groove type ball bearing. The top bearing on all units shall be a single row, double shielded, C3, deep groove type ball bearing. The pump power cable shall be suitable for submersible pump applications and shall be field replaceable utilizing standard submersible pump cable. The cable entrance shall incorporate built in strain relief and a combination three way mechanical compression sealing with a fatigue reducing/thermal expansion boot. The cable entrance assembly shall contain a anti-wicking block to eliminate water incursion into the motor due to capillary wicking should the power cable be accidentally damaged. Motors will be provided with thermal overload protection and seal failure sensors. Controls Pump manufacturer shall provide a Federal Pump series SBS duplex level control system including duplex control panel (for wall mounting) and accessory alarms as detailed in this specification. Duplex Sewage Pump Controller shall include: individual circuit breakers with thru-the-door disconnect handles, across-the line type magnetic starters with overload protection, hoa selector switches, pilot run lights, control circuit transformer with fused secondary , automatic lead/lag alternator, high water alarm light, seal failure alarm light and common alarm horn with silence push button, control relays and numbered terminal strip. The controls shall be provided in a NEMA 1-UL 508 approved enclosure (or as shown in the plans). The SBS control package will include a NEMA 4 junction box and mounting mechanism with float switch cable compression fittings to ensure float switches remain aligned along with (4) non-mercury type tilt level switches . The contractor shall set the level switches as shown in the plans and ensure the high water alarm is set at least 6” below the bottom of the invert. Basin/Pit Accessories The pumps will be installed as shown in the plans. The pump manufacturer will provide the appropriate sized aluminum gas tight cover assembly, spring loaded with hinged cover to allow the pumps to be lifted out of the pit for service and repair. Pump manufacturer will provide base elbows for mounting in basin bottom, guide gar brackets for mounting at upper basin position, stainless steel guide rails that connect to lower base mounted elbow and stainless steel lifting cable connected to lifting lugs provided in motor assembly. Sequence of Operation: Upon rise in liquid level to a predetermined point the lead float switch will initiate lead pump operation and complete the pumping cycle to a predetermined pumps off set point. If the influent conditions rise above a certain rate where the lead pump alone cannot satisfy demand, the lag pump will start at a predetermined set point and work in parallel with the lead pump to satisfy system conditions and pump down to pumps off level. The lead and lag pumps will alternate cycles every 24 hours for even pump loading. In the event a high water level condition occurs, the high water level alarm float switch will activate an alarm horn and light to signal the condition. In the event the lead or lag pump fails the alternate pump will maintain pump conditions until the level is reduced to pumps off set point. An alarm light will be activated along with the alarm horn should one of the pumps fail notifying the user of a failed pump condition. Start-Up Federal Pump’s manufacturer representative will review the installation and be available for start-up . Start-up will include a minimum of (4) complete run cycles and simulated alarm conditions to ensure system operation is complete and to specification.

Suggested Specifications: (Duplex Sewage Pumps-MSC-QD Quick Disconnect Design)

26




7/21/2015

Pumps Furnish and install where shown in the plans a Federal Pump model MSC free standing submersible cutter duplex sewage pump system with each pump flow (GPM) and TDH (Feet) rated as shown on the plans. Casing, impeller, discharge elbow, and motor frame shall be manufactured from gray cast iron with each pump having a field adjustable and or replaceable, high chrome iron cutter plate. Internal and external surfaces coming into contact with the fluid shall be protected by a fused polymer coating. All exposed fasteners shall be stainless steel. All units shall be furnished with a base mounted discharge elbow with discharge flange connections as shown in the plans. Pump to elbow connection shall be metal to metal. Impellers shall be of the single or two-vane semi-open solids handling design equipped with tungsten carbide vane tip and shall be slip fit to the shaft and key driven. All units shall be furnished with a dual inside mechanical shaft seal located completely out of the fluid, running in a separate oil filled chamber and further protected by an exclusionary oil seal located between the bottom seal faces and the fluid being pumped. Pumps shall be provided with silicon carbide versus silicon carbide upper and lower mechanical seal faces. Mechanical seal hardware shall be stainless steel. Motors Motors will be air-filled and provided with 20 feet of submersible power cable and shall be NEMA MG-1, design type B equivalent and rated at full load amps. Motor(s) shall have a 1.15 service factor and shall be rated for 20 starts per hour. Motor(s) shall be air filled, copper wound, class E or F insulated with built in thermal and over current protection for each winding. Motor shaft shall be 420 stainless steel and shall be supported by two permanently lubricated, high temperature ball bearings, with a B-10 life rating at best efficiency point of 60,000 hours. The bottom bearing on pumps rated 7.5 HP and below shall be a single row, double shielded, C3, deep groove type ball bearing. The top bearing on all units shall be a single row, double shielded, C3, deep groove type ball bearing. The pump power cable shall be suitable for submersible pump applications and shall be field replaceable utilizing standard submersible pump cable. The cable entrance shall incorporate built in strain relief and a combination three way mechanical compression sealing with a fatigue reducing/thermal expansion boot. The cable entrance assembly shall contain a anti-wicking block to eliminate water incursion into the motor due to capillary wicking should the power cable be accidentally damaged. Motors will be provided with thermal overload protection and seal failure sensors. Controls Pump manufacturer shall provide a Federal Pump series SBS duplex level control system including duplex control panel (for wall mounting) and accessory alarms as detailed in this specification. Duplex Sewage Pump Controller shall include: individual circuit breakers with thru-the-door disconnect handles, across-the line type magnetic starters with overload protection, hoa selector switches, pilot run lights, control circuit transformer with fused secondary , automatic lead/lag alternator, high water alarm light, seal failure alarm light and common alarm horn with silence push button, control relays and numbered terminal strip. The controls shall be provided in a NEMA 1-UL 508 approved enclosure (or as shown in the plans). The SBS control package will include a NEMA 4 junction box and mounting mechanism with float switch cable compression fittings to ensure float switches remain aligned along with (4) non-mercury type tilt level switches . The contractor shall set the level switches as shown in the plans and ensure the high water alarm is set at least 6” below the bottom of the invert. Basin/Pit Accessories The pumps will be installed as shown in the plans. The pump manufacturer will provide the appropriate sized gas-tight steel cover and frame assembly cover to allow the pumps to be lifted out of the pit for service and repair. Sequence of Operation: Upon rise in liquid level to a predetermined point the lead float switch will initiate lead pump operation and complete the pumping cycle to a predetermined pumps off set point. If the influent conditions rise above a certain rate where the lead pump alone cannot satisfy demand, the lag pump will start at a predetermined set point and work in parallel with the lead pump to satisfy system conditions and pump down to pumps off level. The lead and lag pumps will alternate cycles every 24 hours for even pump loading. In the event a high water level condition occurs, the high water level alarm float switch will activate an alarm horn and light to signal the condition. In the event the lead or lag pump fails the alternate pump will maintain pump conditions until the level is reduced to pumps off set point. An alarm light will be activated along with the alarm horn should one of the pumps fail notifying the user of a failed pump condition. Start-Up Federal Pump’s manufacturer representative will review the installation and be available for start-up . Start-up will include a minimum of (4) complete run cycles and simulated alarm conditions to ensure system operation is complete and to specification.

Suggested Specifications: (Duplex Sewage Pumps-MSC-Free Standing Design)

27




7/21/2015 28

Since 1927 Federal Pump has been a leading provider of reliable and innovative fluid handing solutions for supply water management and dewatering pump services. Its recent introduction of the SP-V and VSPV variable speed domestic water supply systems combine innovative technological advancements in premium efficient motors and innovative variable speed drive support programs that reduce energy demand, lower operating costs and provide more finely tuned water supply systems. Its VSA vertical sewage pump rated to 250 degree F provide solutions in dewatering applications where condensate or boiler feed water are collected and then cooled and pumped to city sewer connections providing continuous service where submersible pumps do not provide a sustainable solution. Oil sensing sump pumps alerting building management to potential oil leaks in the elevator areas provide additional building support solutions. High rise roof fill applications, water make-up systems for mechanical equipment utilizing rain water systems and energy efficient condensate, boiler feed and vacuum condensate units continue in that focus of energy efficiency and buildings support. In the tradition of leadership through product innovation, quality designs and reliable customer service, Federal Pump continues to be a supplier to those water management and dewatering markets where it first started that tradition of leadership in Brooklyn, NY .

Simplex Variable Speed Systems To 300 PSI

SP-V VSPV

Constant Speed Booster To 100 PSI: Type SP

Variable Speed Booster To 100 PSI: Type SP-V

Variable Speed Booster To 300 PSI: Type VSPV

Vertical Sump/Sewage To 1400 GPM and 250 Degree F

Type: VSA

Elevator Sump with Oil Sensor to 1.5HP

Type: POS

1144 Utica Avenue Brooklyn, NY 11203 718-451-2000 www.federalpumps.com

7/21/2015 29

Series MSC Sewage Chopper Pumps - A PumpMan Company · 2018-07-20 · Series MSC-Submersible...

Documents

Transcript of Series MSC Sewage Chopper Pumps - A PumpMan Company · 2018-07-20 · Series MSC-Submersible...