Series MS Miniature Slides General Specifications · 2019. 10. 12. · H Series MS Miniature Slides...
8
H Series MS Miniature Slides www.nkk.com H30 Indicators Accessories Supplement Tactiles Keylocks Rotaries Pushbuttons Illuminated PB Slides Programmable Rockers Touch Tilt Toggles Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC or 3A @ 250V AC Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level: Combines silver & gold ratings (gold over silver) Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold Contact Timing: Nonshorting (break-before-make) Total Travel: On-None-On circuit .087” (2.2mm); all other circuits .138” (3.5mm) Materials & Finishes Actuator: Glass fiber reinforced PBT resin (UL94V-0) Frame: Stainless steel for panel & PCB mount; phosphor bronze with tin plating for bracket mount Dust Cover: Phosphor bronze with nickel plating Case: Glass fiber reinforced diallyl phthalate resin (UL94V-0) Movable Contacts: Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Stationary Contacts: Silver capped copper with silver plating (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Terminals: Copper or brass with silver or gold plating Environmental Data Operating Temp Range: –30°C through +85°C (–22°F through +185°F) Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Wave Soldering recommended (PC Mount). See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 rated actuator & case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. All Single & Double Pole Double Throw models recognized at 6A @ 125V AC & 3A @ 250V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. All Double Throw & 3 Throw models certified at 6A @ 125V AC, 3A @ 250V AC, & 0.4VA maximum @ 28V DC. General Specifications
Transcript of Series MS Miniature Slides General Specifications · 2019. 10. 12. · H Series MS Miniature Slides...
H
Series MS Miniature Slides
www.nkk.comH30
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
lt To
ggle
s
Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC or 3A @ 250V AC Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level: Combines silver & gold ratings (gold over silver) Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold Contact Timing: Nonshorting (break-before-make) Total Travel: On-None-On circuit .087” (2.2mm); all other circuits .138” (3.5mm)
Materials & Finishes Actuator: Glass fiber reinforced PBT resin (UL94V-0) Frame: Stainless steel for panel & PCB mount; phosphor bronze with tin plating for bracket mount Dust Cover: Phosphor bronze with nickel plating Case: Glass fiber reinforced diallyl phthalate resin (UL94V-0) Movable Contacts: Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Stationary Contacts: Silver capped copper with silver plating (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Terminals: Copper or brass with silver or gold plating
Environmental Data Operating Temp Range: –30°C through +85°C (–22°F through +185°F) Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Processing Soldering: Wave Soldering recommended (PC Mount). See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications Flammability Standards: UL94V-0 rated actuator & case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. All Single & Double Pole Double Throw models recognized at 6A @ 125V AC & 3A @ 250V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. All Double Throw & 3 Throw models certified at 6A @ 125V AC, 3A @ 250V AC, & 0.4VA maximum @ 28V DC.
General Specifications
H
Series MSMiniature Slides
www.nkk.com H31
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
ltTo
ggle
s
Available in flat frame and bracketed PC mounting types.
Over-center actuator block and plunger design gives crisp actuation with clear indication of circuit status; this design also diminishes sparking and increases operating life.
Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability.
Antijamming design protects contacts from damage due to excessive downward force on the actuator.
High internal barriers between poles and insulating sheet between case and actuator block give added protection to contacts.
Specially composed silver alloy contacts for power applications or gold contacts for logic level applications give high contact reliability.
Prominent external insulating barriers increase insulation resistance and dielectric strength.
Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants.
Clinching of frame to case well above base and terminals provides 1,500V dielectric strength. Actual Size
Distinctive Characteristics
H
Series MS Miniature Slides
www.nkk.comH32
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
lt To
ggle
s
Actuators
A .150” (3.8mm) Wide for Single or Double Pole
B .323” (8.2mm) Wide for Double Pole
1 AMS
Gold Contacts with 0.4VA Rating
SPDT ON-NONE-ON Circuit
Circuits2 ON NONE ON
3 ON OFF ON
0 ON ON ON
Contact Materials & Ratings
W Silver; Rated 6A @ 125V AC & 3A @ 250V AC
G Gold; Rated 0.4VA max. @ 28V AC/DC max.
AGold over Silver; Rated 6A @ 125V AC & 0.4VA max. @ 28V AC/DC max.
2
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
MS12ASG30
G
.150” (3.8mm) Wide Actuator
30
Mounting
F Panel Mount (Terminal 01 only)
N PCB Mount (Terminal 03 only)
SBracket Mount (Terminals 13, 30, & 40 only)
Terminals01 Solder Lug
03 Straight PC
13 Straight with Bracket
30 Right Angle PC
40 Vertical PC
Poles1 SPDT
2 DPDTSP3T
Right Angle PC Terminals with Support Bracket
S
TYPICAL SWITCH ORDERING EXAMPLE
IMPORTANT: Switches are supplied without UL, cULus & CSA marking unless specified.UL, cULus & CSA recognized only when ordered with marking on the switch.Specific models, ratings, & ordering instructions are noted on the General Specifications page.
H
Series MSMiniature Slides
www.nkk.com H33
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
ltTo
ggle
s
Slide Position Connected Terminals Throw & Schematics
Pole Model
Left Center Right Left Center RightNote: Terminal numbers are not actually on the switch.
SPMS12MS13
ONON
NONEOFF
ONON
2-1 OPEN 2-3 SPDT
DPMS22MS23
ONON
NONEOFF
ONON
2-1 5-4 OPEN 2-3 5-6 DPDT
For 3 Throw (3-On)
Connected Terminals & Schematics
Pole Model Left Center Right External Connection
SP MS20
ON ON ON The SP3T model utilizes a double pole base.
External connections must be made during field installation.2-1 5-4 2-3 5-4 2-3 5-6
ACTUATORS
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range.
W
Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum
Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC
Gold over Silver
POLES & CIRCUITS
2 (COM)
31
1 3 4 6
2 5 (COM)
A
G
A
CONTACT MATERIALS & RATINGS
Note: Complete explanation of operating range in Supplement section.
Power Level 6A @ 125V AC or Logic Level or 0.4VA maximum @ 28V AC/DC maximum
.150” (3.8mm) Wide for Single Pole
(out)
6 3
2
14
5
(out)(out)
ExternalConn
Common(in)
.150” (3.8mm) Wide for Double Pole B .323” (8.2mm) Wide
for Double Pole Only
(3.8).150
(3.8).150
(3.8).150
(8.2).323
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External Connection
(3.8).150
(3.8).150
H
Series MS Miniature Slides
www.nkk.comH34
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
lt To
ggle
s
Epoxy Seal
(2.0).079
(2.0).079
(4.0).157
(1.1).043
Thk = (0.8) .031
MOUNTING TYPES & TERMINALS
Panel Mount(Combines with Solder Lug Terminal 01 only)
Support Bracket Mount (For Terminals 13, 30, & 40)
F
S
Straight PC Mount(Combines withStraight PC Terminal 03 only)
N
13Solder Lug01 Straight PC03
TYPICAL SWITCH DIMENSIONS
Solder Lug Terminals Single Pole
MS12AFW01 Actuator in LEFT Position
Solder Lug Terminals Double Pole
MS22BFW01 Actuator in LEFT Position
Dimension A = .268” (6.8mm) for on-none-on .319” (8.1mm) for on-off-on & on-on-on
Maximum Panel Thickness: .197” (5.0mm)
(17.53).690
(2.4) Dia Typ.094
A
(9.0).354
(17.53).690
(2.4) Dia Typ.094
A
(4.19).165
SP or DP with .150” (3.8mm) Actuator
DP only with .323” (8.2mm) Actuator
Maximum Panel Thickness: For Straight PC with Bracket Terminal 13: .197” (5.0mm) For Angle Mount Terminals 30 & 40: .177” (4.5mm)
Straight PC with Bracket
Right Angle PC30
Vertical PC40
Epoxy Seal (4.8).189
(6.35).250
(1.17).046
Thk = (0.8) .031
(3.8).150
(1.1) x (2.0) Typ.043 x .079
(0.8) Typ.031
(4.7) Typ.185
(0.5).020
(0.4).016
(5.1).201
(6.4).252
(4.5).177
ON
ON
(12.7).500
3
2
1
(0.5).020
(2.0).079
(6.1).240
(19.6).772
(17.53) .690
(1.2) R Typ.047
(8.2).323
(6.1).240
(19.6).772
(17.53) .690
(1.2) R Typ.047
(3.8).150
6
5
4 1
2
3
(2.0) Typ.079
(12.7).500
(4.8).189
(0.5).020
(11.4).449
(6.1).240
(6.6).260
(19.6).772
(17.53) .690
(1.2) R Typ.047
(3.8).150
(3.8).150
(1.1) x (2.0) Typ.043 x .079
(0.8) Typ.031
(4.7) Typ.185
(0.5).020
(0.4).016
(5.1).201
(6.4).252
(4.5).177
ON
ON
H
Series MSMiniature Slides
www.nkk.com H35
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
ltTo
ggle
s
TYPICAL SWITCH DIMENSIONS
Single Pole Straight PC Terminals with Bracket
Actuator in LEFT Position MS12ANG03
Actuator in LEFT Position MS22BNG03
Double Pole Straight PC Terminals
Single Pole Straight PC Terminals
Actuator in LEFT Position MS22BSG13
2
1
3
(1.6) Typ.063
(7.9) Typ.311
(4.7) Typ.185
(1.8) Dia Typ.073 (1.5) Dia Typ.059
(4.7) Typ.185
(1.8) Dia Typ.073
1
2
3
(4.7) Typ.185
(4.8).189
(1.8) Dia Typ.073
1
2
3 6
5
4
2
1 4
5
63
(1.6) Typ.063
(2.4) Typ.095
(7.9) Typ.311
(4.7) Typ.185
(1.8) Dia Typ.073 (1.5) Dia Typ.059CL
Double Pole Straight PC Terminals with Bracket
Actuator in LEFT Position MS12ASG13
(3.8).150
(0.8) Typ.031
(4.7) Typ.185
(4.8).189
(5.1).201
(7.6).299
(6.35) .250
ON
ON
6
5
4 1
2
3
(1.17) Typ.046
(12.7).500
(4.8).189
(0.5).020
(11.4).449
(3.8).150
(0.8) Typ.031
(4.7) Typ.185
(0.36) .014
(5.1).201
(13.1).516
(6.7).264
(15.8).622
(4.8).189 (0.4) Typ
.016
ON
ON
(12.7).500
3
2
1
(0.5).020(1.17).046
(7.1).280
(3.2).126 (1.2) Typ
.047
6
5
4 1
2
3
(1.2) Typ.047
(12.7).500
(4.8).189
(0.5).020
(11.9).469
(1.17) Typ.046
(3.2).126
(3.8).150
(0.8) Typ.031
(4.7) Typ.185
(4.8).189
(5.1).201
(6.4).252
(6.35) .250
ON
ON
(12.7).500
3
2
1
(0.5).020
(1.17).046
(8.2).323
(3.8).150
(3.8).150
(5.6).220
(3.8).150
(10.4).409
(8.2).323
(10.4).409
(3.8).150
(0.8) Typ.031
(4.7) Typ.185
(0.36) .014
(5.1).201
(14.3).563
(6.7).264
(15.8).622
(4.8).189 (0.4) Typ
.016
ON
ON
(6.6).260
(3.8).150
H
Series MS Miniature Slides
www.nkk.comH36
Indi
cato
rsA
cces
sori
esSu
pple
men
tTa
ctile
sK
eylo
cks
Rota
ries
Push
butto
nsIll
umin
ated
PB
Slid
esPr
ogra
mm
able
Rock
ers
Touc
hTi
lt To
ggle
s
TYPICAL SWITCH DIMENSIONS
Right Angle PC Terminals Single Pole
MS12ASG30 Actuator in LEFT Position
Right Angle PC Terminals Double Pole
MS22BSG30 Actuator in LEFT Position
Vertical PC Terminals Single Pole
MS12ASG40 Actuator in LEFT Position
Vertical PC Terminals Double Pole
MS22BSG40 Actuator in LEFT Position
3 2 1
(1.8) Dia Typ.073 (4.7) Typ
.185
(9.53) .375
(6.6) Typ.260
(1.5) Dia Typ.059
(1.5) Dia Typ.059
2 13
(4.7) Typ.185
(6.6) Typ.260
(12.7).500
5 46
(3.81) .150
(1.8) Dia Typ.073
(10.16) .400
(1.5) Dia Typ.059
2
1
3
(4.45) Typ .175
(3.81) Typ.150
(1.8) Dia Typ.073
(4.8).189
(1.5) Dia Typ.059
1
2
3
(12.7).500
(4.45) Typ .175
(3.81) Typ .150
4
5
6
(1.8) Dia Typ.073
(5.7).224
(9.53) .375
(1.2).047
(1.27).050
(0.5).020
(3.2).126(3.81)
.150
(3.8).150
(5.1).201
(12.7).500
1 2 3
(6.6).260
(0.8) Typ.031
(4.7) Typ.185
(6.6).260
1
2
3
(12.7).500
(0.5).020
(1.27).050
(11.4).449
1
2
36
4
5 (12.7).500
(0.5).020
(4.8).189
(1.27) Typ.050
(12.7).500
(11.4).449
4 5 6
1 2 3
(4.7) Typ.185
(0.8) Typ.031
(6.2).245
(3.2).126
(0.5).020
(3.81) .150
(1.27) Typ.050
(1.2).047
(5.7).224
(12.7).500
(8.2).323
(5.1).201
(3.8).150
(13.2).520
(0.4) Typ.016
(3.8).150
(3.8).150
(13.2).520
(0.4) Typ.016
(1.2) Typ.047
(4.45) .175
(3.8).150
(3.8).150
(0.4).016
(5.3).209
(5.1).201
(10.16) .400
(3.81) Typ .150
(0.8) Typ.031
(2.7).106
(6.9).270
ON
ON
(3.8).150
(1.2) Typ.047
(4.45) .175
(8.2).323
(1.2) Typ.047
(4.45) .175
(3.8).150
(0.4).016
(5.3).209
(5.1).201
(12.7).500
(3.81) Typ .150
(0.8) Typ.031
(2.7).106
(6.9).270
ON
ON
(0.4) Typ.016
(13.2).520
(3.8).150
Notes
www.nkk.com H37
