September 2011 HI-Tech Project Magazine (1)
description
Transcript of September 2011 HI-Tech Project Magazine (1)
HI-Tech Projects
September 2011
Over 100 Project Profile
SELECT AND START OWN INDUSTRY
Egg a food item which is very much nutritious and also good for health. A food item which is to be eaten in the breakfast with the bread thus acts as a perfect healthy product which makes us to remain fit and fine. The important aspect is egg products can be alternatively turned into a powder. Two main parts of an egg the egg yolk and the egg white are pasteurized before they are sent for drying. Egg whites are very much known to carry lots of sugar which is also known as glucose with which they are fermented to remove the sugar and then the product is evaporated under high temperature using the drying chambers. The hot air thus evaporates and thus also removes the moisture by producing the egg powder which is then placed in the hot chamber for pasteurization. In this way and in this process the egg powder is procured.
EGG POWDER
Cost EstimationPlant Capacity 10,00,000 EGGS PROCESSING/Day Land & Building (Area 10 Acres) Rs. 6.07 Cr.Plant & Machinery Rs. 10 Cr. W.C. for 1 Months Rs. 8.57 Cr. Total Capital Investment Rs. 27.34 Cr. Rate of Return 67% Break Even Point 34%
A common enzyme known as papain is obtained from the green papaya (pawpaw) fruit. Enzymes are proteins that can increase the rate of biological changes such as the ripening of fruit. At the end of an enzyme catalysed reaction the enzyme itself is unchanged and is able to react again. Enzymes can be generally recognized by the ending -ase. This either indicates the nature of the substance affected by the enzyme (e.g. carbohydrase acts on carbohydrate material and proteases acts on proteins) or to indicate the nature of the reaction e.g. transferases catalyse the transfer of atoms or groups of atoms within a substance.
PAPAIN FROM PAPAYA
Cost EstimationPlant Capacity 40 KGS/Day Land & Building (Area 2 Acres) Rs. 60 LacsPlant & Machinery Rs. 14 Lacs W.C. for 1 Months Rs. 10 Lacs Total Capital Investment Rs. 1.03 Cr. Rate of Return 45% Break Even Point 47%
Castor oil obtained by a combination of pressing and extraction from the seeds of the castor oil plant (Ricinus communis) consists of upto 90% of triglyceride of ricinoleic acid, 12 hydroxy oleic acid. The hydroxyl number of castor oil is 161-169. The component glycerides of castor oil (% mole) comprise saturated-diricinoleins (7.3%) oleo-diricinoleins (2.5%) Linoleo diricinoleins (13.4%), Dihydroxy Stearo diricinoldins (2%) Triricinolein (74.8%).
CASTOR OIL AND ITS DERIVATIVES OLEO RESINS, TURKEY RED OIL, DCO, HCO,
SEBACIC ACID, 12-HYDROXY STEARIC ACID
Cost EstimationPlant Capacity 16.94 MT./Day Land & Building (Area 3 Acres) Rs. 81 LacsPlant & Machinery Rs. 88 Lacs W.C. for 3 Months Rs. 11 Cr. Total Capital Investment Rs. 12.90 Cr. Rate of Return 114% Break Even Point 14%
Gin, vodka, and related spirits like aquarit are distinguishable from whisky, rum and brandy which themselves have a number of common characteristics. The most evident difference is in colour, with gin an vodka normally being colourless white whisky, rum and brandy vary in shade from straw-coloured to the deepest brown. This immediate difference is linked with distinguishing features of composition and flavour which are reflected in the methods of production of the two troup of sprits. The aurd whisky comes from the Gaelic word wisge-beatha, as the Irish called it, incoming the water of life. The colour in whisky, rum and brandy oves it origin to the practice of ageing or maturing these spirits in wooden casks, which as containers have previously used for transporting some compatible liquid such as slerry, wine or molasses. Residues of previous contents, together with substance extracted from the wood itself, serve to give the maturing spirit a brown colour which in interest of standardization, is supplmented by the addition of caremel. The requirement for maturation in wood is now codified in lay standing whisky is the potable spirit obtained by distillation of an aquons extract of an infusion of matted barly and after cereals that has been ferriented with strains of sacctromyus ceramisial. Various types of whisky are produced in a number of different countries in the world. They differ principally in the nature and proportion of the cerels used as a raw materials along with matted barly and also in the type of still used for distillation. The principal types of whisky are also characterised of particular geographical regions of the world.
WHISKY (IMFL)
Cost EstimationPlant Capacity 30000 Lit/Day Land & Building (Area 6 Acres) Rs. 3.56 Cr.Plant & Machinery Rs. 11.05 Cr. W.C. for 1 Months Rs. 3.77 Cr. Total Capital Investment Rs. 21 Cr. Rate of Return 164% Break Even Point 26%
Don't Waste Time Call Immediately09811437895
TIME IS MONEY
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 3 :-
Patrons you can deposit the amount
in EIRI Account
HDFC BANKCA-05532020001279(RTGS/NEFT IFSC :HDFC 00005531)
Face fresher tissue paper, when applied on the face, it removes the dirts, soils from face skin and freshen the face and keep it moist. The skin becomes glossy and fresh appearance. In a modern age people are more prone to sophisticate modes of maintaining health and hygienic conditions of their body through the contingencies of cosmetics and other allied measures which promote these functions effectively. This is eleganthy achieved by the application of wet face freshner tissue. This is very economical item and portable. It can be easily carried out in pocket while going in a car, flight, rail etc. This is a product of recent times as a nice out come of innovation in cosmetology. After the use of this item one feel very much fresh, comfortable, cosy. Now a days it is even a part of fashion to use such a handy item in the upper stetra of society. Where grace is often exhibited. By using this item people feel highly dignified while attending seminar, meetings conferences, symposium, congregations, debates, gettogether marriage parties and other parties, social function etc. Even it is very much acceptable item by the modern working lady, models, filmstars, air hostess, college girls, opera dancers, business executives, corporate executives etc.
PAPER NAPKINS
Cost EstimationPlant Capacity 200 KGS/Day Land & Building (Area 500 sq.mt.) RENTED Plant & Machinery Rs. 10 Lacs W.C. for 3 Months Rs. 18 Lacs Total Capital Investment Rs. 30 Lacs Rate of Return 39% Break Even Point 52%
Wet face freshner tissue paper contains cream or lotion, when applied on the face, it removes dirts & soils from face skin and freshens the face and keeps it moist. The skin becomes glossy and fresh. In modern age people are more prone to sophisticat modes of maintaining health and hygienic conditions of their body through the contingencies of cosmetics and other allied measures which promote these functions effectively. This is eleganthy achieved by the application of wet face freshner tissue. This is very economical item and portable. It can be easily carried in pocket while going in a car, flight, rail etc.
WET FACE FRESHNER TISSUE
Cost EstimationPlant Capacity 200 KGS/Day Land & Building (Area 500 sq.mt.) RENTED Plant & Machinery Rs. 10 Lacs W.C. for 3 Months Rs. 18 Lacs Total Capital Investment Rs. 30 Lacs Rate of Return 39% Break Even Point 52%
Coal tar pitch is a byproduct of turning coal into coke or coal gas. It is a sticky, dark brown or black liquid that resists flowing and has a very strong smell. In most cases, the volume of coal tar pitch used in medicinal preparations is very small in comparison to the amounts produced. As a result, most of the pitch is further processed to remove useful chemicals or is simply burned. Crude Coal Tar received from by-product coke oven plants is heated to temperatures up to 400oC in specially designed distillation stills. This removes moisture, Naphthalene, Light Creosote Oil and Heavy Creosote Oil from the Coal Tar. The resultant product is called Coal Tar Pitch. Depending on the blend of Crude Coal Tar and the temperatures to which the distillation is carried out different grades of Coal Tar Pitch are produced.
COAL TAR PITCH
Cost EstimationPlant Capacity 25 MT./Day Land & Building (Area 1 Acre) Rs. 1.27 Cr.Plant & Machinery Rs. 75 Lacs W.C. for 3 Months Rs. 5.49 Cr. Total Capital Investment Rs. 7.65 Cr. Rate of Return 73% Break Even Point 29%
Caustic soda lye, also known as sodium hydroxide (NaoH) is an important industrial chemical product produced on a tonnage basis in both solid and liquid form. It is deliquescent, absorbing water vapour and carbon dioxide from the air. It is also extremely corrosive and should be handled with great care. Adequate protection from body contact with the solid form or concentrated solutions should be provided. It is also a fire hazard compound as it heats spontaneously and may ignite combustible materials that are nearly. A large part of the huge amount used annually in the U.S. (About 21/2 million tons) is produced by the electrolysis of the sodium chloride solutions in the electrolylic cells, such as the Hooxer, Nelson, Force, or Allen-Moore. Chlorine is a by product of the reaction. Alternative process is the soda-lime method.
CAUSTIC SODA FROM SODIUM CHLORIDE (CAUSTIC SODA LYE)
Cost EstimationPlant Capacity 10 Ton/Day Land & Building (Area 1 Acre) Rs. 1.32 Cr.Plant & Machinery Rs. 80 Lacs W.C. for 3 Months Rs. 1.10 Cr. Total Capital Investment Rs. 3.43 Cr. Rate of Return 91% Break Even Point 31%
Barium Carbonate is a is white amorphous powder. It is one of the basic Barium salts and finds applications in many areas. Natural barium carbonate, was formerly mined com merially in England. Precipitated barium car bonate is the most widely used barium chemical with the exception of natural barite. It is a fine white powder with an absolute density of 4.25 and bulk density varying from 0.80 to 2.16 g/em3 (50-135 lb/ft3). depending on the grade. The commercial material assays 99% BaCO3. 0.06-0.12% total sulfur as S.Particle size varies with the grade.
BARIUM CARBONATE
Cost EstimationPlant Capacity 1 MT./Day Land & Building (Area 1500 sq.mt.) RENTEDPlant & Machinery Rs. 21 Lacs W.C. for 1 Months Rs. 9 Lacs Total Capital Investment Rs. 32 Lacs Rate of Return 32% Break Even Point 72%
Aluminium is a metal with high strength-to-weight ratio, better formability, high ductility, anti-corrosive properties, with thermal and electrical conductivity. Because of these unique combinat ion of propert ies, aluminium(including its al loys) has substantially replaced a number of traditional materials from their established uses e.g. steel, copper, lead and zinc among metals and glass. Wood and paper among non-metals. Aluminium is crucial for expansion of power availability and electrification programme. It has a significant role to play in saving energy in transportation sector, thus help reducing the consumption petroleum products.
ALUMINIUM INGOTS FROM ALUMINIUM SCRAP
Cost EstimationPlant Capacity 20 Tons/Day Land & Building (Area 2000 sq.mt.)Rs. 1.67 Cr.Plant & Machinery Rs. 1.41 Cr. W.C. for 1 Months Rs. 10.19 Cr. Total Capital Investment Rs. 13.52 Cr. Rate of Return 34% Break Even Point 40%
TECHNO ECONOMIC DETAILED PROJECT REPORTS FROM EIRI
Just Call Eiri &
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 4 :-
Contact
for required Project report apart from this list.
These properties have made aluminium highly useful in manufacture of aircraft, passenger cars, railway rolling stock, ship building, electrical eng. manufacture of cine and photographic equipments, radio components, window frames and doors, railings, refinery equipments, foils, extruded sections and pipes for a wide range of uses. Aluminium powder is also used in paints and anodising industries. Extruded aluminium products are finding growing exports prospects. Aluminium extruded products are mainly tubes, pipes and blanks. These are manufactured in various forms and can be broadly classified in (a) rods & (b) sections. Sections include leath hollow and solid sections. In extrusion, the cylindrical rod called billet, is squeezed hydraulically into any shape by forcing the hot billet through the die orifice. Extrusion presses of various sizes are available ranging from 200 ton to 5000 tons capacity. These presses can be designed from simple to very complicated type with intricate and most sophisticated components equipments.
ALUMINIUM EXTRUSION
Cost EstimationPlant Capacity 20 MT./Day Land & Building (Area 5 Acres) Rs. 5.02 Cr.Plant & Machinery Rs. 6.12 Cr. W.C. for 1 Months Rs. 8.62 Cr. Total Capital Investment Rs. 21.28 Cr. Rate of Return 29% Break Even Point 65%
High-density polyethylene (HDPE) or polyethylene high-density (PEHD) is a polyethylene thermoplastic made from petroleum. It takes 1.75 kilograms of petroleum (in terms of energy and raw materials) to make one kilogram of HDPE. HDPE is commonly recycled, and has the number “2” as its recycling symbol. In 2010, the global HDPE market reached a volume of more than 50 million tons. HDPE has little branching, giving it stronger intermolecular forces and tensile strength than lower-density polyethylene. The difference in strength exceeds the difference in density, giving HDPE a higher specific strength. It is also harder and more opaque and can withstand somewhat higher temperatures (120 0C/ 248 0F for short periods, 110 0C /230 0F continuously). High-density polyethylene, unlike polypropylene, cannot withstand normally-required autoclaving conditions. The lack of branching is ensured by an appropriate choice of catalyst (e.g., Ziegler-Natta catalysts) and reaction conditions. HDPE contains the chemical elements carbon and hydrogen.
H.D.P.E. BOTTLES
Cost EstimationPlant Capacity 480000 Nos./Day Land & Building (Area 5000 sq.mt.)Rs. 2.17 Cr. Plant & Machinery Rs. 1.49 Cr. W.C. for 1 Months Rs. 78 Lacs Total Capital Investment Rs. 4.88 Cr. Rate of Return 105% Break Even Point 26%
The mineral graphite is one of the allotropes of carbon. It was named by Abraham Gottlob Werner in 1789 from the Ancient Greek ????? (graph?), “to draw/write”,for its use in pencils, where it is commonly called lead (not to be confused with the metallic element lead). Unlike diamond (another carbon allotrope), graphite is an electrical conductor, a semimetal. It is, consequently, useful in such applications as arc lamp electrodes. Graphite is the most stable form of carbon under standard conditions. Therefore, it is used in thermo chemistry as the standard state for defining the heat of formation of carbon compounds. Graphite may be considered the highest grade of coal, just above anthracite and alternatively called meta-anthracite, although it is not normally used as fuel because it is difficult to ignite.
GRAPHITE MINING AND BENIFICATION PLANT
Cost EstimationPlant Capacity 12 MT./Day Land & Building (Area 5 Acres) Rs. 96 LacsPlant & Machinery Rs. 2.74 Cr. W.C. for 3 Months Rs. 81 Lacs Total Capital Investment Rs. 4.76 Cr. Rate of Return 76% Break Even Point 30%
Energy is becoming a scarce and costly input in the world. Oil which accounts for a sizeable portion of our energy consumption, has been making a very heavy tax on our foreign exchange resources. Other than coal, we must also find alternate resources of energy centred around solar, wind, tidal and bio-gas. An effective bio-gas programme leads to efficient use of cow dung for gas recovery and partial supplement to plant nutrient requirement. Bio-gas programme leads to improvement in rural living including rural sanitation. Convertional bio-gas digesters set up in India were predominently of the Khadi Village Industries Commission Model. Recently Janta Bio-gas plant designed by Planning Research and Action Division (PRAD) of State Planning Institute, Lucknow based on bio gas technology has proved to be comparatively more economical. Several Janta Biogas plants have been constructed in Uttar Pradesh and a few in Haryana.
BIO GAS PLANT
Cost EstimationPlant Capacity 120 CUM/Day Land & Building (Area 800 sq.mt.) Rs. 15 LacsPlant & Machinery Rs. 3 Lacs W.C. for 2 Months Rs. 3 Lacs Total Capital Investment Rs. 23 Lacs Rate of Return 20% Break Even Point 68%
The mineral graphite is one of the allotropes of carbon. It was named by Abraham Gottlob Werner in 1789 from the Ancient Greek ????? (graph?), “to draw/write”,for its use in pencils, where it is commonly called lead (not to be confused with the metallic element lead). Unlike diamond (another carbon allotrope), graphite is an electrical conductor, a semimetal. It is, consequently, useful in such applications as arc lamp electrodes. Graphite is the most stable form of carbon under standard conditions. Therefore, it is used in thermo chemistry as the standard state for defining the heat of formation of carbon compounds. Graphite may be considered the highest grade of coal, just above anthracite and alternatively called meta-anthracite, although it is not normally used as fuel because it is difficult to ignite.
GRAPHITE MINING AND BENIFICATION PLANT
Cost EstimationPlant Capacity 12 MT./Day Land & Building (Area 5 Acres) Rs. 96 LacsPlant & Machinery Rs. 2.74 Cr. W.C. for 3 Months Rs. 81 Lacs Total Capital Investment Rs. 4.76 Cr. Rate of Return 76% Break Even Point 30%
Hi-Tech ProjectsAn Industrial Monthly Magazine on
Hi-Tech Projects & developed and under developing Technologies with lucrative
Project opportunitiesEditor
Sudhir Gupta (Industrial Consultant)
SUBSCRIPTION RATESFOR INDIA: Single Copy Rs. 20/-
One Year Rs. 225/- Three Years Rs. 650/-
(Add Rs. 50/- for outstation cheques. Please make the Draft/Cheque in favour of “Engineers India Research Institute, Delhi”
FOR OVERSEAS: Single Copy US$ 5/- One Year US$ 60/-
Three Years US$ 170/-
Project Reports/Profiles provided in this issue had been prepared on data available at the time of preparing these reports. Entrepreneurs / Industrialists are requested to please update the data before venturing into any project mentioned herein. However efforts have been made to provide Correct information even then no guarantee can be given about the authenticity of the matter. All disputes are subject to Delhi Jurisdiction only.
CAUTION
You can startYour Own
INDUSTRY
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 5 :-
Rs.975/-
Rs.2500/-
Dextrose (D-Glucose, Corn sugar, starch sugar, blood sugar, grape sugar) is by far the most abundant sugar in nature and occurs either in free state (monosaccharide form) or chemically linked with other sugar varieties. In the free state it occurs in substantial quantities in honey, fruits, and berries. As a polymer of anhydrous dextrose units it occurs in starch, cellulose and glycovsl. Sucrose is a disaccharide of dextrose and fructose. Commercial production of dextrose by hydrolysis of starch yields white crystalline sugars that are either anhydrous (C6H12o6) or hydrated (C6H12O6. H2O). Starch hydrolysis was first practised commercially in the united states in the year 1842 while methods of crystallisation of crystalline dextrose were developed in 1920 crystalline dextrose became a main industrial product afterwards Dextrose is manufactured from a variety of starches from wheat potato, sweet potato and tapioca as well as corn. Commercial dextrose product include crystalline monohydrate or anhydrous dextrose and liquid dextrose.
Cost EstimationPlant Capacity 1 Ton./Day Land & Building (Area 1000 sq.mt.) Rs. 44 LacsPlant & Machinery Rs. 24 Lacs W.C. for 3 Months Rs. 53 Lacs Total Capital Investment Rs. 1.25 Cr. Rate of Return 35% Break Even Point 62%
DEXTROSE MONOHYDRATE & DEXTROSE ANHYDROUS
POWDER FROM TAPIOCA STARCH
Prior to go ahead first one can think as what is a Battery. Battery is a device to change the chemical energy in electrical energy through chemical reaction. It consist of two plates i.e. Cathode & Anode & electrolyte. During the reaction with the plates (electrodes) this electrolyte produces the electrons on the negative electrode which goes to positive electrode (anode) via-outer load circuit. One can ask a question as when the cathode after reacting with electrolyte produces the electron i.e. means the reaction will continue whether the battery is in operation will continue whether the battery is in operation or not means there is a loss of energy but it is not in actual practice as the electron produced during off period remains there on the electrode & prevent the further chemical reaction.
Cost EstimationPlant Capacity 200 Nos./Day Land & Building (Area 1000 sq.mt.) Rs. 78 LacsPlant & Machinery Rs. 74 Lacs W.C. for 3 Months Rs. 6.29 Cr. Total Capital Investment Rs. 7.97 Cr. Rate of Return 63% Break Even Point 28%
STORAGE BATTERY
Particle board is as the name suggests a board made of particles of bagasse. Thus particle board is a board made from bagasse which is bonded by means of a resin under the application of pressure and temperature. The organic binder resin used are normally urea formaldehyde if the particle board is to be used for interior use, or phenol formaldehyde is used if this is used in external exposurer or under severe internal conditions. Melamine formaldehyde is also used. The first plant to produce particle board commercially was built in Bremen, West Germany in 1941. The first three layer particle board was marketed in Switzerland in 1945. Particle boards find extensive use in the building industry furniture industry cabinets and automobile construction large size panels can also be manufactured at economic costs.
Cost EstimationPlant Capacity 2 Ton/Day Land & Building (Area 3000 sq.mt.) Rs. 2.79 Cr.Plant & Machinery Rs. 37 Lacs W.C. for 2 Months Rs. 88 Lacs Total Capital Investment Rs. 4.14 Cr. Rate of Return 27% Break Even Point 70%
PARTICLE BOARD FROM BAGASSE
Sodium formate (sodium salt of formic Acid) HCOONa is an important compound having versatile field of application and the material shall be in the form of white granules or crystalline powder or aqueous solution with slight odour of formic acid. It finds its application in the manufacture of formic acid, oxalic acid, organic chemical and in the manufacture of sodium dithionite. It is used as a reducing agent and analytical chemistry as a precipitant for the noble metals it also act as a buffering agent. The demand of the product is increasing day by day.
Cost EstimationPlant Capacity 5 MT./Day Land & Building (Area 2000 sq.mt.) Rs. 88 LacsPlant & Machinery Rs. 29 Lacs W.C. for 3 Months Rs. 68 Lacs Total Capital Investment Rs. 1.93 Cr. Rate of Return 33% Break Even Point 48%
SODIUM FORMATE
Vermicelli is a popular instant food product. It falls under the category of extruded product and is made from wheat flour. At times tapioca or soybean or groundnut flour is also added. Thus, it is rich in proteins and liked by people from all walks of life, irrespective of age. It is basically a snack food item and at times it is also used as a table enricher. With changing lifestyles, greater awareness about health and preference for instant food items have made vermicelli very popular and an item of mass consumption.
Cost EstimationPlant Capacity 10000 Packets/Day Land & Building (Area 2000 sq.mt.) Rs. 1.06 Cr.Plant & Machinery Rs. 26 Lacs W.C. for 3 Months Rs. 98 Lacs Total Capital Investment Rs. 2.34 Cr. Rate of Return 45% Break Even Point 43%
VERMICELLI
J. Darius Bikoff, a self-proclaimed health nut born on September 21, 1961, first conceived of the idea of vitamin enhanced water in 1996. According to him, he was feeling “run down” and concerned he was catching a cold, so he took some Vitamin C and drank some mineral water. As he consumed the items, he started thinking about the idea of having them together instead of having to take them separately. He founded Energy Brands in May 1996 using his personal savings and contracting with an aquifer in Connecticut for the base water used. The individual products carried the Glaciau name, with the company’s first product being Glaciau Smartwater.
Cost EstimationPlant Capacity 5000 Ltr./Day Land & Building (Area 20000 sq.mt.)Rs. 6.85 Cr.Plant & Machinery Rs. 13.20 Cr. W.C. for 3 Months Rs. 60 Lacs Total Capital Investment Rs. 20.95 Cr. Rate of Return 18% Break Even Point 62%
VITAMIN WATER
MODERN
TECHNOLOGY
OF
EXTRUSION
& EXTRUDED
PRODUCTSRs. 800/-
Patrons you can deposit the amount in EIRI Account
ICICI BANK LTD.CA-038705000994
(RTGS/NEFT/IFSCCode : ICIC0000387)
Just published in 2011
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 6 :-
Rs. 1250/-
Rs. 975/-
New 2011 Edition
57. PAPER BAGS (SHOPPING BAGS) 32 Lacs 58. PAPPAD PLANT (AUTOMATIC) 30 Lacs 59. PICKLES, MURABBAS AND
SAUCES ETC. (E.O.UNIT) 46 Lacs 60. PLASTIC TOYS (E.O.UNIT) 7 Lacs 61. POTATO WAFFERS/CHIPS (E.O.U) 97 Lacs 62. PAINT INDUSTRY (E.O.UNIT) 37 Lacs 63. PAPER CARRY BAGS 98 Lacs 64. P.V.C. PIPES AND FITTINGS 1.57 Cr.65. PRESSURE COOKER (E.O.U) 42 Lacs 66. POTATO POWDER (E.O.UNIT) 1.96 Cr. 67. RUBBER GOODS FROM
WASTE RUBBER 29 Lacs 68. READYMADE GARMENT (E.O.U) 75 Lacs 69. RICE MILL 4.11 Cr.70. SOCKS KNITTING 25 Lacs 71. SOYABEAN PRODUCTS (E.O.U) 4.68 Cr.72.SHAMPOO (E.O.UNIT) 29 Lacs 73. SUGAR PLANT (E.O.UNIT) 23.61 Cr.74. SAFED MUSLI CULTIVATION
& PROCESSING (EXTRACT & POWDER) (E.O.U) 62 Lacs
75. STEVIA CULTIVATION & EXTRACTION (E.O.UNIT) 1.24 Cr.
76. THINNERS 30 Lacs 77. TABLET, CAPSULES,
(PHARMACEUTICAL UNIT) 48 Lacs 78. TEA BAGS (E.O.UNIT) 69 Lacs 79. TEA PACKING & DISTRIBUTION 4.50 Cr.80. TOILET SOAP (E.O.UNIT) 84 Lacs 81. TOMATO PRODUCTS IN
POUCHES (E.O.UNIT) 58 Lacs 82. WOODEN FURNITURE (E.O.U) 1.81 Cr.83. ZARDA KIMAM & TOBACCO 12 Lacs
PROJECT NAME PROJECT COST
Each Project Report covers in this CD contains Introduction, Uses, Market,
Process with Product Formulae, Suppliers of Plant and Equipments, Cost Economics with Profitability Analysis, BEP, Resources of Finance etc. Price of this CD containing
all above 83 Project Reports is just Rs. 20000/- or US$ 600/-. Payable fully in
advance through Draft/M.O./At Par Cheque in favour of ENGINEERS INDIA RESEARCH INSTITUTE, DELHI. Delivery within 1 day.
(To Order please dial : 98114-37895)
A standard steel fabrication workshop consists of a shed with (L x W x H) 100m x 20m x 12m and all facilities for fabricating all kinds of universal steel. It includes, steel shearing, punching, forming, welding, rolling, sandblasting, plasma cutting and painting. It can be used in making structural steel and equipment. Such as, Flats, Angles, T Bars, Channels, Angle, Posts, Universal Beams & Columns, Sub Floor Access Doors, wide flange columns and beams, structural HSS and channel shapes, welded wide flange, deep girder beams, open web steel joists, etc. Planning is a continuous movement towards desired goals. While preise formulation of our five year plans objectives have varied from plan-to-plan, the essential goals have remained unchanged.
Cost EstimationLand & Building (Area 2000 sq.mt.)s. 1 Cr.Plant & Machinery Rs. 33 Lacs W.C. for 3 Months Rs. 82 Lacs Total Capital Investment Rs. 2.25 Cr. Rate of Return 108% Break Even Point 28%
STEEL FABRICATION WORKSHOP
A standard steel fabrication workshop consists of a shed with (L x W x H) 100m x 20m x 12m and all facilities for fabricating all kinds of universal steel. It includes, steel shearing, punching, forming, welding, rolling, sandblasting, plasma cutting and painting. It can be used in making structural steel and equipment. Such as, Flats, Angles, T Bars, Channels, Angle, Posts, Universal Beams & Columns, Sub Floor Access Doors, wide flange columns and beams, structural HSS and channel shapes, welded wide flange, deep girder beams, open web steel joists, etc. Planning is a continuous movement towards desired goals. While preise formulation of our five year plans objectives have varied from plan-to-plan, the essential goals have remained unchanged.
Cost EstimationLand & Building (Area 2000 sq.mt.)s. 1 Cr.Plant & Machinery Rs. 33 Lacs W.C. for 3 Months Rs. 82 Lacs Total Capital Investment Rs. 2.25 Cr. Rate of Return 108% Break Even Point 28%
STEEL FABRICATION WORKSHOP
831. ACTIVATED CARBON FROM
SAW DUST, RICE HUSK AND COCONUTSHELL 77 Lacs
2. AGARBATTI SYNTHETIC PERFUMERY COMPOUNDS 74 Lacs
3. AIR CONDITIONERS & PARTS 49 Lacs 4. AUTOMATIC BISCUIT PLANT 69 Lacs 5. AFTER SHAVE LOTION 33 Lacs 6. AYURVEDIC MEDICINES 69 Lacs 7. ALUMINIUM UTENSILS 3.61 Cr.8. BEER PLANT 15.33 Cr.9. BUFFALOW MEAT PROCESSING 2.37 Cr.10. BANANA POWDER (E.O.UNIT) 69 Lacs 11. CEILING FAN (E.O.UNIT) 42 Lacs 12. COCONUT OIL FROM COPRA 1.06 Cr.13. COLD DRINKS 5 Lacs 14. COMPUTER SOFTWARE (E.O.U) 2.61 Cr.15. CONFECTIONERY INDUSTRY
(TOFFEE & CANDY) (E.O.UNIT) 64 Lacs 16. CORN FLAKES 78 Lacs 17. CHEWING TOBACCO (KHAINE) 21 Lacs 18. CALCIUM CARBONATE 3.36 Cr.19. COSMETICS INDUSTRY
(MODERN) (E.O.UNIT) 3.29 Cr.20. CEMENT PAINT 11 Lacs 21. C.P. BATHROOM FITTINGS 89 Lacs 22. CARBON PAPER 43 Lacs 23. CYCLE TYRES & TUBES (E.O.U) 3 Cr.24. DISPOSABLE PLASTIC SYRINGES
(STERILIZED) (E.O.UNIT) 1.29 Cr.25. DAIRY PRODUCTS & MILK
PACKAGING (E.O.UNIT) 1.84 Cr.26. DETERGENT CAKE & POWDER 6 Lacs 27. DETERGENT POWDER (E.O.U) 9 Lacs 28. EXTRACTION OF ESSENTIAL OILS
(CARDAMOM, JEERA, AJOWAN, GINGER OIL ETC) & PACKING OF GROUND SPICE (E.O.UNIT) 58 Lacs
29. EXERCISE NOTE BOOK & REGISTER (E.O.UNIT) 30 Lacs
30. FLORICULTURE (CUT FLOWERS) 1.45 Cr.31. FRUIT JUICE MAKING &
PACKING IN PLASTIC CONTAINERS (POUCHES) (E.O.UNIT) 3.66 Cr.
32. FOOD DEHYDRATION (E.O.U) 2.24 Cr.33. FOOD PROCESSING 1.13 Cr.34. GARLIC OIL ——--— 35. GINGER OIL 69 Lacs 36. GINGER PROCESSING (PEELING,
DRYING, GRINDING, BLEACHING OF FRESH GINGER) (E.O.UNIT) 1.24 Cr.
37. GUAR GUM 2.86 Cr.38. HAND MADE PAPER (E.O.UNIT) 55 Lacs 39. HERBAL COSMETIC (E.O.UNIT) 76 Lacs 40. HERBAL EXTRACTS (E.O.UNIT) 7.58 Cr.41. JAM, JELLY, CHUTNEY, PICKLES
AND SQUASHES (E.O.UNIT) 53 Lacs42. LEATHER, GARMENTS, SHOES
& CHAPPALS (E.O.UNIT) 2.64 Cr.43. LATEX RUBBER CONDOMS (E.O.U) 52 Lacs 44. MINIATURE CIRCUIT BREAKER 88 Lacs 45. MANGO PROCESSING & CANNING
(MANGO PULP) (E.O.UNIT) 49 Lacs 46. MEDICINAL PLANT EXTRACTS 71 Lacs 47. MENTHOL BOLD CRYSTALS 22 Lacs 48. MINERAL WATER (IN POUCHES
& PLASTIC BOTTLES) (E.O.U) 2.89 Cr.49. MUSHROOMS (CULTIVATION &
PROCESSING UNIT) (E.O.UNIT) 54 Lacs 50. MASALA/SPICES (E.O.UNIT) 51 Lacs 51. MUSTARD OIL (EDIBLE OIL) 3.51 Cr. 52. NAMKEEN INDUSTRY (BHUJIA,
CHANA CHUR ETC.) (E.O.UNIT) 8 Lacs 53. NUTS, BOLTS, RIVETS & WASHERS 66 Lacs 54. OIL SEALS (E.O.UNIT) 36 Lacs 55. PAPER GLASSES FOR
BEVERAGE (E.O.UNIT) 68 Lacs 56. PAN MASALA IN POUCH AND
TIN PACK SODA, MEETHA, ZARDA & KIMAM (E.O.UNIT) 72 Lacs
Export Orinted Units
(100% EOU/EOU)
Projects
(83 Project Reports)
Rs. 20,000/-PROJECT NAME PROJECT COST
Contact
for required Project report apart from this list.
Patrons you can deposit the amount in EIRI Account
STATE BANK OF INDIACA-30408535340
(IFS Code : SBIN 0001067)
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 7 :-
The book Modern Technology of Modern Technology of Acid Slurry, Surfactants, Soap and Detergents with Formulae covers Soap, Fatty Acids and Synthetic Detergents, Detergent Components, Surfactants, Builders, Raw Materials, Analysis and Testing, Manufacture of Acid Slurry, Manufacture of Soap, Technology of Surfactants, Manufacture of Synthetic Detergents, Detergent Soap and Additives.
Rs. 850/-
New 2011 Edition
281. BANANA POWDER 69 Lacs 2. CURCUMIN & TURMERIC OIL
FROM TURMERIC 61 Lacs 3. DEHYDRATION OF JACK FRUIT
81 Lacs 4. DEHYDRATION OF FIGS
BY SUN DRYING METHOD 63 Lacs 5. DEHYDRATION OF ONION
AND GARLIC 6.79 Cr.6. DESICCATED COCONUT
POWDER 71 Lacs 7. DRY GINGER POWDER AND
OLEORESIN 84 Lacs 8. DRY GINGER (GINGER POWDER) 50 Lacs 9. FRUIT JUICES, SQUASHES ETC. 1.13 Cr.10. ONIONS & ONION POWDER 98 Lacs 11. EGG POWDER 25.40 Cr.12. FRUIT JUICE POWDER 3.21 Cr.13. FRUITS AND VEGETABLE
DEHYDRATION 1.64 Cr.14. GLUCOSE-D POWDER 98 Lacs 15. GARLIC FLAKES AND
POWDER (DEHYDRATED) 71 Lacs 16. GRAPE DEHYDRATION 73 Lacs 17. INSTANT FOOD 40 Lacs 18. MANGO POWDER 88 Lacs 19. MUSTARD POWDER 1.12 Cr. 20. MILK POWDER & GHEE 81 Lacs 21. MANGO JUICE 1.36 Cr. 22. ORANGE JUICE 2.93 Cr.23. PINE APPLE JUICE 1.48 Cr.24. POTATO POWDER 48 Lacs 25. TURMERIC POWDER
(EDIBLE GRADE) 33 Lacs 26. TAMARIND JUICE POWDER 69 Lacs 27. TOMATO POWDER 64 Lacs 28. YEAST DRY POWDER
FROM MAIZE 1.14 Cr.
Price of this CD containing all above 28 Project Reports is Rs. 16000/- or US $ 600/-. Payable fully in advance through Draft/M.O.
in favour of ENGINEERS INDIA RESEARCH
INSTITUTE, DELHI. Delivery within 2 days. (To Order please dial mobile: 098114-37895
Sudhir Gupta).
FRUIT JUICES, FOOD
DEHYDRATION ANDALLIED PROJECTSRs. 16,000/- ONLY
FOR CD
PROJECT NAME PROJECT COST
Electrical Tower sub station Structural Telecom Tower are the important structural members and is the back bone Telecommunication sector. These towers are fabricated by means of bolted joints only.The structural steels of well specified quality only are used in construction of towers and structure to ensure the permissible stresses and other design details. Practices followed in material selection, design, fabrication, testing and must suit the field conditions of this country. Various design considerations are adopted in the design of self-supporting steel lattice towers for overhead transmission lines, including loads, combination of loads, permissible stresses, wind pressures likely to be experienced during service and atmospheric corrosion intensity.
Cost EstimationPlant Capacity 50 MT./Day Land & Building (Area 6000 sq.mt. Rs. 4.04 Cr.Plant & Machinery Rs. 1.51 Cr. W.C. for 3 Months Rs. 16.94 Cr. Total Capital Investment Rs. 22.70 Cr. Rate of Return 21%
STATION STRUCTURE TELECOM TOWER STRUCTURAL STEEL MEMBERS
Alum is available in solid form as powder, granular, kibbled & lump form. It can also be purchased and fed as a liquid. Alum can be effective in the pH range of 5.5. to 7.8, but seems to work best in most water supplies in a pH range of 6.8 to 7.5. Below a pH range of 5.5, alkalinity in the water supply is generally insufficient. The aluminum ions become soluble rather than insoluble and do not participate in the hydration and reactions necessary to make the alum effective as a coagulant. In these instances the plant may experience higher than normal filtered water turbidites, and much of the aluminum will pass through the filters. When the pH level of the water is above 7.8 after the addition of the alum, the aluminum ions again become soluble, and the efficiency of coagulation is decreased. Under these condition, aluminum ions again penetrate the filters, and post filtration alum coagulation can occur in the clear well and in the distribution system in some cases.
Cost EstimationPlant Capacity 20 MT./Day Land & Building (Area 4000 sq.mt.)Rs. 1.92 Cr.Plant & Machinery Rs. 70 Lacs W.C. for 2 Months Rs. 61 Lacs Total Capital Investment Rs. 3.55 Cr. Rate of Return 20% Break Even Point 67%Break Even Point 47%
FERRIC ALUM
Bottling plant is a plant where beverages are put into bottles with a cap. These bottles are widely used for storage purposes. Liquefied petroleum gas (LPG) consists mainly of propane, propylene, butane, and butylene in various mixtures. However, in the United States, the mixture is mainly propane. It is produced as a by-product of natural gas processing and petroleum refining. The components of LPG are gases at normal temperatures and pressures. LPG bottling plant is a plant where LPG is put into bottles for storage. The plant has the facility to recieve bulk LPG by pipeline from a reliable source or any area. This is the safest and the cheapest way of transporting bulk LPG. The plant is equipped with hydraulic cylinder testing equipment for periodic testing of the cylinders. To ensure safe and accurate filling of the cylinders well experienced technical people should only be employed in the working of the plant.
Cost EstimationPlant Capacity 10000 Cylinders/Day Land & Build. (Area 10000 sq.mt.)Rs. 10.26 Cr.Plant & Machinery Rs. 2 Cr. W.C. for 2 Months Rs. 5.24 Cr. Total Capital Investment Rs. 24.77 Cr. Rate of Return 39% Break Even Point 33%
L.P.G. BOTTLING PLANT
Liquid Chlorine is produced by electrolysis of brine solution and during the process Sodium Hydroxide & Hydrogen gas are produced. Caustic soda, also known as sodium hydroxide (NaoH) is an important industrial chemical product produced on a tonnage basis in both solid and liquid form. It is deliquescent, absorbing water vapour and carbon dioxide from the air. It is also extremely corrosive and should be handled with great care. Adequate protection from bodly contact with the solid form or concentrated solutions should be provided. Liquid Chlorine is produced by the electrolysis of the sodium chloride solutions in the electrolylic cells, such as the Hooxer, Nelson, Force, or Allen-Moore. Chlorine is a by product of the reaction.
Cost EstimationPlant Capacity 5 Ton/Day Land & Building (Area 3000 sq.mt.) Rs. 80 LacsPlant & Machinery Rs. 3.43 Cr. W.C. for 1 Months Rs. 14 Lacs Total Capital Investment Rs. 4.51 Cr. Rate of Return 23% Break Even Point 61%
LIQUID CHLORINE BY ELECTROLYSIS OF BRINE
Processing of textile materials involves the use of diverse types of compounds to perform various functions. The compounds are variously known as textile auxiliaries, textile chemicals, textile process chemicals etc. They may be broadly classified depending on he purpose for which they are used into two groups (1) Those which are used in textile processing to serve some purpose or purposes and after these purposes are served, they have to be removed from the textile material being processed and (2) those which continue to form an integral part of the materials being processed by way of either chemical reaction with the textile substrate or mechanical deposition of water soluble or water insoluble substances in the textile substrate and are expected to remain on the material more or less permanently with standing the subsequent rigorous action of varying degrees exerted on the end products during the use by the consumers.
Cost EstimationPlant Capacity 1 MT./Day Land & Building (Area 500 sq.mt.) Rs. 39 LacsPlant & Machinery Rs. 21 Lacs W.C. for 1 Months Rs. 13 Lacs Total Capital Investment Rs. 79 Lacs Rate of Return 47% Break Even Point 61%
DYE LEVELLING AGENT
Contact
for required Project report apart from this list.
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 8 :-
Potato is widely consumed as food all over the world. Cooked potatoes, in various forms are offered in restaurants and refreshment stalls and variety of processed potato products are available in the market. Surplus and cull potatoes are used as feed for livestock and also as raw material for the manufacture of starch, ethyl alcohol and a few other industrial products. Potatoes are consumed not only as a fresh vegetable, but also in a variety of processed forms. Dehydrated potato products have been known for long and are especially valued because they afford convenience for use; they have good storage stability and are relatively any to transport. In recent years, there has been, a great spurt in the consumption of processed products, such as potato chips, dehydrated meshed potatoes, and frozen potato products.
Cost EstimationPlant Capacity 1200 KGS/Day Land & Building (Area 2000 sq.mt.) Rs. 96 LacsPlant & Machinery Rs. 1.64 Cr. W.C. for 1 Months Rs. 38 Lacs Total Capital Investment Rs. 3.40 Cr. Rate of Return 96% Break Even Point 34%Break Even Point 47%
POTATO CHIPS
Sugarcane juice in tetra pack must be a demandable product as there are few units which are producing mango juice, guava juice, mixed juice and orange juice in tetra packs but not sugar cane. Tetrapack sugar cane juice will fetch the good market as this is a new concept for our country. Preservation is done when Juice or food is kept for longer period without any deteriorated or spoils the juice by the direct contact with atmosphere. Juice are spoiled by decomposition due to aqueous content in the Juice itself and oxygen and other gases plus moisture in the atmosphere. This content provides healthy condition for micro organisms to growth which spoils the food. The oxygen present in atmosphere or air also helps the microorganisms to grow.
Cost EstimationPlant Capacity 20000 Nos./Day Land & Building (Area 3 Acres) Rs. 1.91 Cr.Plant & Machinery Rs. 12.75 Lacs W.C. for 1 Months Rs. 36 Lacs Total Capital Investment Rs. 15.46 Cr. Rate of Return 19% Break Even Point 65%
SUGARCANE JUICE IN TETRAPACK
Milk is an Important human food. It is palatable, easy to digest and highly nutritives. It contains proteins, fat, sugar, minerals and a liberal quantity of different kinds of vitamins. In World milk production, India ranks next only to the United States of America and the U.S.S.R. But the milk produced in India is far from adequate for its vast population as the daily average consumption per head comes to even less than half of the optimum requirement of about 310 grams. The importance of milk in human diet especially for children and expectant and nursing matters is vital. To meet the demand of the increasing population milk production in India has to be increased upto about 64 million tonnes by 2000 Ad. It is neither possible nor desirable to increase the cattle and buffalo population to achieve this target. This can only be achieved by stepping up milk production of our bovine population by cross breeding of cows and use of improved cows and buffaloes.
Cost EstimationPlant Capacity 50000 Ltr./Day Land & Build (Area 25000 sq.mt.) Rs. 14.63 Cr.Plant & Machinery Rs. 4.98 Lacs W.C. for 13 Months Rs. 5.75 Cr. Total Capital Investment Rs. 26.68 Cr. Rate of Return 60% Break Even Point 39%
DAIRY PRODUCTS - MILK PACKAGING IN POUCH (50,000 LTR/DAY) MILK PROCESSING (GHEE, BUTTER,
PANEER, CASEIN, FLAVOURED MILK, CHEESE, YOGHURT AND ICE CREAM)
Modern days are changes with the advance of scientific discovery. Due to the scarcity of time now human beings changes their food habits. No body can pay much more time for their preparation of food, every body wants to get ready made fresh food, such that human being can save their time. They do not want to loss their valuable time in the preparation of daily food. By this thiming now a days these different kind of food materials developed, like instant tea, instant coffee, instant milk, instant rice etc. On the above point of view bakery products are cheaper, largely accepted ready made food. Now the advancement of age use of bakery foods will gradually increases and utilisation will be around the proportional of certain percentage of population increase.
Cost EstimationLand & Building (Area 4000 sq.mt.) Rs. 1.63 Cr.Plant & Machinery Rs. 60 Lacs W.C. for 3 Months Rs. 1.84 Cr. Total Capital Investment Rs. 4.24 Cr. Rate of Return 63% Break Even Point 30%
AUTOMATIC BREAD AND BISCUIT PLANT
241. BRAKE OIL 32 Lacs 2. BITUMEN 30 Lacs 3. CALCIUM BASE GREASE 96 Lacs 4. DOT-4 BRAKE OIL ——— 5. EMULSIFIERS FOR CUTTING OILS 27 Lacs 6. EXTRA HIGH TEMPERATURE
LUBRICATING GREASE 93 Lacs 7. FOOD GRADE GREASE
OR LUBRICANT 1.79 Cr.8. FUEL OIL 2.76 Cr.9. LITHIUM BASED GREASES 84 Lacs 10. LUBE OIL & GREASES 25 Lacs 11. MOLYBDENUM BASED LUBRICANT 67 Lacs 12. PETROLEUM JELLY 32 Lacs 13. REFINERY PETROL/DIESEL ETC. 68 Lacs 14.RECLAMATION OF
TRANSFORMER OIL ——— 15. RECLAMATION OF
HYDRAULIC OIL ——— 16. RECLAMATION OF USED ENGINE OIL
(BY CLAY AND VACUUM DISTILLATION PROCESS) 94 Lacs
17. RUST PREVENTION LUBE OIL 1.40 Cr.18. SILICON GREASE 2.54 Cr.19. SOLUBLE CUTTING OIL 5.14 Cr.20. TEFLON GREASE 4.02 Cr.21. TRANSFORMER OIL 86 Lacs 22. TURBINE OIL 78 Lacs 23. WIRE DRAWING LUBRICANTS 43 Lacs 24. WHITE OIL FROM KEROSENE OIL 75 Lacs
Price of this CD containing all above 24 Project Reports is Rs. 22,000/- or US $ 700/-. Payable fully in advance through Draft/M.O. in favour of ENGINEERS INDIA RESEARCH
INSTITUTE. Delivery within 2 days. (To Order dial: 098114-37895 Gupta).
LUBRICATING OILS, GREASES, BRAKE
OILS, BITUMEN, TRANSFORMER OIL,
RECLAMATION OF USED ENGINE OILS, CUTTING OILS AND ALLIED PROJECTS
IN CD
PROJECT NAME PROJECT COST
In the processing of tea, a certain percentage of the total tea produced accumulates as tea waste in the form of sweepings or fluff, stacks and leaves. This waste has a caffeine content of 1.5-3.5% and presents itself as an attractive raw material for production of a very valuable product - caffeine. Caffeine is widely used in pharmaceuticals both as a free base and as mixture (e.g. citrated caffeine and caffeine/sodium benzoate) The Regional Research Laboratory, jorhat has developed a process for extraction of caffeine from tea waste. Presently one firm uses this technology commercially and produces about 25-30 tonnes of caffeine per annum.
Cost EstimationPlant Capacity 40000 KGS/Day Land & Building (Area 1500 sq.mt.) Rs. 1.14 Cr.Plant & Machinery Rs. 94 Lacs W.C. for 3 Months Rs. 1.85 Cr. Total Capital Investment Rs. 4.02 Cr. Rate of Return 51% Break Even Point 37%
CAFFINE FROM TEA WASTE
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 9 :-
CANDLE MAKINGPROCESSES AND FORMULATIONS
HAND BOOKRs. 380/-
Contact Eiri for any
PROJECT REPORT/
INDUSTRIAL BOOK
09811437895
Potato is widely consumed as food all over the world. Cooked potatoes, in various forms are offered in restaurants and refreshment stalls and variety of processed potato products are available in the market. Surplus and cull potatoes are used as feed for livestock and also as raw material for the manufacture of starch, ethyl alcohol and a few other industrial products. Potatoes are consumed not only as a fresh vegetable, but also in a variety of processed forms. Dehydrated potato products have been known for long and are especially valued because they afford convenience for use; they have good storage stability and are relatively any to transport. In recent years, there has been, a great spurt in the consumption of processed products, such as potato chips, dehydrated meshed potatoes, and frozen potato products.
Cost EstimationPlant Capacity 1200 KGS/Day Land & Building (Area 2000 sq.mt.) Rs. 96 LacsPlant & Machinery Rs. 1.64 Cr. W.C. for 1 Months Rs. 38 Lacs Total Capital Investment Rs. 3.40 Cr. Rate of Return 96% Break Even Point 34%Break Even Point 47%
POTATO CHIPS
231. BUTTER MILK 100 Lacs2. CASEIN FROM MILK 22 Cr.3. CONDENSED SWEETENED MILK WITH
CONTAINERS MANUFACTURING 41 Cr.4. CONDENSED MILK SWEETENED 53 Cr.5. DAIRY FARM TO PRODUCE
MILK & GOAT FARM 56 Cr.6. DAIRY FARMING & DAIRY PROD. 204 Lacs7. DAIRY FARM TO PRODUCE MILK
(JERSEY COW) 45 Lacs8. DAIRY FARM TO PRODUCE MILK
(BUFFALOE) 24 Lacs 9. DAIRY DEVELOPMENT 185 Lacs10. FLAVOURED MILK (STERILIZED) 62 Lacs11. GHEE AND BUTTER 106 Lacs12. ICE CREAM OF DIFF. FLAVOURS 78 Lacs 13. LACTOSE AND BY-PRODUCTS
PROCESSING FROM MILK 14 Lacs14. MILK TOFFEE MANUFACTURES 12 Lacs15. MITHAI/HALWAI (SW. & NA.) 46 Lacs16. MILK POWDER & GHEE 145 Lacs17. MILK CHILLING PLANT 73 Lacs 18. MILK PROCESSING PLANT 162 Lacs 19. PROCESSED CHEESE 68 Lacs20. PEANUT MILK, KEFIR, FLAVOURED
PEANUT MILK MILK BEVERAGE 13 Lacs 21. SOYA MILK & PANEER 148 Lacs 22. TONED MILK 6.66 Cr.23. YOGHURT 2.38 Cr.
Each Project Report covers in this CD contains Introduction, Uses, Market, Process with Product
Formulae, Suppliers of Plant and Equipments, Cost Economics with Profitability Analysis, BEP,
Resources of Finance etc. Price of this CD containing all above 23 Project
Reports is Rs. 18000/- or US $ 500/-. Payable fully in advance through Draft/M.O. in favour of ENGINEERS INDIA RESEARCH INSTITUTE,
DELHI. Delivery within 1 day. (To Order please dial : 98114-37895).
DAIRY FARMING (BUFFALLO & COWS.) DAIRY PRODUCTS &
OTHER MILK PROCESSING INDUSTRIES
PROJECT NAME PROJECT COST
COST RS. 18,000/- FOR ALL 23 PROJECTS REPORTS IN CD
New materials and processing routes provide opportunities for the production of advanced high performance structures for different applications. Ceramic fibers is one of these promising materials. Ceramic fiber is an insulation made of an alumina-silica composition, held together by an inorganic binder. It’s commonly used as a refractory material. Its lightweight, low-density properties make it ideally suited for high temperature applications requiring low thermal mass. Due to it superior heat resistant properties, ceramic fibers are used widely in industrial plants where heat resistance is required. Some of common applications are in foundries, power plants , furnaces & kilns .some of common products made are rolls, blankets and hardboards. There are major 2 types of ceramic fibers. 1. Vitreous Ceramic fiber 2. crystalline ceramic fibers. Most high temperature insulation materials like ceramic fibers have to be applied in extremely large thicknesses to achieve such values. Hence it is produced in large quantities. Increasing adoption of products like bio low persistent ceramic fibers is analyzed.
Cost EstimationPlant Capacity 7000 KGS/Day Land & Building (Area 5 Acres) Rs. 5.24 Cr.Plant & Machinery Rs. 15 Cr. W.C. for 3 Months Rs. 3.44 Cr. Total Capital Investment Rs. 25 Cr. Rate of Return 16% Break Even Point 65%
FIBRE BLANKET, CERAMIC FIBRE BOARD
AND CERAMIC FIBRE ROPE
The term alcohol was first applied to the spirits of wine, ethyl alcohol, and now it refers to a series of substances with similar characteristics Ethyl alcohol is the active constituent of all intoxicating liquars obtained by the fermentation of saccharine materials. It is present in the form of esters in several volatile oils. It is now a days prepared in immense quantities, chiefly by fermentation and finds numerous industrial uses, and is also being used as a motor fuel.
Cost EstimationPlant Capacity 40000 Lts./Day Land & Building (Area 70 Acres) Rs. 12 Cr.Plant & Machinery Rs. 2.02 Cr. W.C. for 3 Months Rs. 5.02 Cr. Total Capital Investment Rs. 19.36 Cr. Rate of Return 64% Break Even Point 26%
DISTILLERY
Calcination of Pyrophyllite and Diaspore mineral by using vertical shaft Kiln is a important process to produce the calcined product o frespective minerals. Pyrophyllite Al2 S14 O10(OH) is a hydrous aluminium silicate found in metamorphic rocks and is genera l ly found in Nor th Carb ina California,New foundLand & Japan. Diaspore Al2O3 H2o ia a natural hydrous aluminium oxide occurring inbauxite and with corundum and dolmite and found in Arkansa Missouri, Pennsylvana,Switzerland & Czechoslovaki. The calcined Pyrophyllite (Aluminium Silicate) and calcined diaspore (aluminium Oxide or Alumina) have found versatile application in chemical process industries.
Cost EstimationPlant Capacity 100 MT./Day Land & Build. (Area 10000 sq.mt.) Rs. 4.45 Cr.Plant & Machinery Rs. 1.10 Cr. W.C. for 3 Months Rs. 7.23 Cr. Total Capital Investment Rs. 12.92 Cr. Rate of Return 40% Break Even Point 32%
CALCINATION PLANT FOR PYROPHYLLITE &
DIASPORE MINERALS BY VERTICAL STAF KILN PROCESS
A plastic is any one of a large and varied group of materials which consists of an essential ingredient combinations of carbon with oxygen, hydrogen, nitrogen and other organic and inorganic elements. While solid in the finished state, at some stage in its manufacture it has been or can be formed into various shapes by flow-usually through the application singly or together of heat and pressure.
Cost EstimationPlant Capacity 2400 KGS/Day Land & Building (Area 1000 sq.mt.) Rs. 45 LacsPlant & Machinery Rs. 12 Lacs W.C. for 3 Months Rs. 39 Lacs Total Capital Investment Rs. 97 Lacs Rate of Return 26% Break Even Point 62%
PLASTIC WASTE RECYCLING PLANT (RUFIA WASHING)
Contact
for required Project report apart from this list.
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 10 :-
Among the alcoholic drinks, Beer is quite common and popular in almost every Country of the World. People of different Countries take beer in varying much like a soft drink in European Countries it is just a substitute of water. The alcoholic contents and main source stuff also keep varying according to the tests of the major part of population of the particular country although it is a fashion to ask for beer of every origin in every Country. Formulations of beer manufacturing are done with the view of availability of the raw materials in that particular part of the World where the brewery is proposed to be established. In most of the parts of the world, barley is a universal source of beer extraction. But, beers are manufactured from Chamomile flowers and powdered gingers etc. as well. Separate formulations have been adopted for every major ingredient used in brewing & distillation of beer.
Cost EstimationPlant Capacity 16666 Ltr./Day Land & Building (Area 38 Bighas) Rs. 6.04 Cr.Plant & Machinery Rs. 24 Lacs W.C. for 3 Months Rs. 10.57 Cr. Total Capital Investment Rs. 55.09 Cr. Rate of Return 31% Break Even Point 53%
BEER INDUSTRY
Tie-rod ends are used for steering control wheel alignment in automobile industries. This is adjusted with tie-rod during tie-in assembling. Different types and Dimensions of tie rod ends are manufactured ascending to the vehicles like Car, Metador, Tractor, Truck etc. First of all it must be understood that the entire matter of steering control is dependent upon the tyres maintaining a close and intimate contact with the rod surface. This close contact is influenced by tyre tread, tyre inflation, wheel balance, weight on the wheel, shock absorber conditions, spring action and wheel angularity. This applies to all four wheels and also to the individual wheels. It may be readily understood that unbalanced forces will exist if one front tyre has a wide flat tread and other front tyre has a narrow non-skid pattern in contact with the road.
Cost EstimationLand & Building (Area 500 sq.mt.) Rs. 26 LacsPlant & Machinery Rs. 9 Lacs W.C. for 3 Months Rs. 21 Lacs Total Capital Investment Rs. 57 Lacs Rate of Return 22% Break Even Point 62%
TIE-ROD ENDS
Aluminium si l icate are exceedingly numerous & important. They contain different proportions of Al2O3 & S1O2. As an anhydrous silicate, with silicate of iron, calcium Magnesium etc., Aluminium occurs is in varieties of garret, crystallizing in the regular system. As silicates of aluminium, calcium & sodium it is used firmerly as ultra marine. As silicates of Aluminium combined with potassium & Magnesium it occurs is micas. As double silicates of Aluminium, potassium Sodium Magnesium or calcium, it forms varieties of felspar which occurs in immense quantity. But the decomposition of felspar by carbonic acid in the atmosphere & in rain or spring water, the alkaline compounds are removed, leaving Kaolin or clay of more or less purity which under pressure, become hardened & laminated forming shade & finally state. Many of the islicates of aluminium are of great importance
Cost EstimationPlant Capacity 2 Ton./Day Land & Building (Area 1000 sq.mt.)Rs. 24 LacsPlant & Machinery Rs. 7 Lacs W.C. for 2 Months Rs. 36 Lacs Total Capital Investment Rs. 69 Lacs Rate of Return 90% Break Even Point 26%
ALUMINIUM SILICATE
O r g a n i c c o m p o u n d s o t h e r t h a n carbohydrates that taste sweet have been known for centuries. The amino acid, glycerines whose name derives from its taste is a familiar examples. The sweetening compound must be water soluble sine water insoluble substances have no taste Reasonable solubility and a rapid rate of solution are necessary for some application. On the other hand the sweetener should not be hygroscopic since this wound impede manufacturing packaging, distribution & use. Ideally the product should cost less than sucrose on an equivalent sweetners. Saccharin Sodium is a sodium derivative of O-benzoic Sulphimide. It contain not less 98% and not more than the equivalent of 100.5% of C7H4O3 NS Na Calculated into reference to the substances drived to constant weight at 105oC. Saccharin is a white crystalline powder odourless or with a faint aromatic odour taste intensely sweet even in dilute solution. It is efforcescent in nature.
INSOLUBLE SACCHARINE (USING SOLID INGREDIENTS)
Cost EstimationPlant Capacity 50 KGS/Day Land & Building (Area 700 sq.mt.) Rs. 33 LacsPlant & Machinery Rs. 7 Lacs W.C. for 3 Months Rs. 8 Lacs Total Capital Investment Rs. 50 Lacs Rate of Return 34% Break Even Point 49%
Elastic Waist Band (Latex - Based) is used for inner lining of dress material viz. night suits, trousers, panties, undergarments, bra-straps, readymade garments & stockings etc. and their field of application is quite extensive in the arena of garment and apparel. As their field of application is far-stretched, eventually their market potential calls forth for bright future scope. The manufacture of Elastic Waist Band (Latex Based) takes recourse to the raw material as Rubber Thread (Latex Based) which is subjected to certain mechanical operations including formation of continuous rows links from Rubber Threads. stiching on the stitching machine etc. The demand of the product is increasing considerably.
Cost EstimationPlant Capacity 3000 Mtr./Day Land & Building (Area 300 sq.mt.) Rs. 8 LacsPlant & Machinery Rs. 19 Lacs W.C. for 3 Months Rs. 13 Lacs Total Capital Investment Rs. 45 Lacs Rate of Return 32% Break Even Point 52%
ELASTIC WAIST BAND (LATEX BASED)
Dyes are classified by a variety of schemes. Classes based on usage, or method of application are of greatest value to the dyes, classes based on chemical composition are of more use to the chemist. Dyes can also be classified with regards to the substrates, e.g. wool dyes include acid, direct, lencovat and metal complex dyes. Polyamides can be dyed with these same colorants in addition to disperese dyes. Dyes are classified in the following manner.
Cost EstimationPlant Capacity 10 MT./Day Land & Building (Area 3000 sq.mt.) Rs. 46 LacsPlant & Machinery Rs. 1.24 Cr. W.C. for 3 Months Rs. 6.33 Cr.Total Capital Investment Rs. 8.14 Cr. Rate of Return 42% Break Even Point 32%
BETA - NAPHTHOL (100% E.O.U.)
Over30,000
PROJECTS REPORTS
Aailablewith
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 11 :-
Exercise books & registers are used in large quantities in schools, colleges, Research Laboratories & other educational Institutions. Private & Goverment organisations use these products of necessity for accounting & record keeping purposes with increased population & overall development. Demand for exercise Books & Registers is increasing continuously. Two types of paper are used for making exercise Books & Registers viz. ruled & plane. For ruling, the paper is passed through a double sided disc rulling machine. The required number od sheets are then stucke with printed cover. Due to rapid industrealisation taking place in the country the demand for office stationary is increasing day by day.
Cost EstimationPlant Cap. 6000 Nos/Day Note Books (200 Pages) 1560 Nos/Day Registers (96 Pages) Land & Building (Area 600 sq.mt.) Rs. 18 LacsPlant & Machinery Rs. 9 Lacs W.C. for 1 Months Rs. 15 Lacs Total Capital Investment Rs. 43 Lacs Rate of Return 98% Break Even Point 23%
NOTE BOOK AND REGISTER MAKING
Among various kinds of adhesives Starch Based Adhesives constitute their paramount significance. These are generally clasified according to the processing they receive prior to compounding them into adhesives. These are vegetable adhesives. However there are innumerable variety of starch adhesives depending upon their origin and processing condition.
Cost EstimationPlant Capacity 2 Ton./Day Land & Building (Area 500 sq.mt.) Rs. 13 LacsPlant & Machinery Rs. 7 Lacs W.C. for 3 Months Rs. 32 Lacs Total Capital Investment Rs. 54 Lacs Rate of Return 34% Break Even Point 42%
INDUSTRIAL ADHESIVE BASED ON STARCH GUM,
DEXTRINE SILICATE
Essential power cables used for transmission and distribution purposes consist of conductors stranded from plain high conductive annealed copper wires insulated with oil-impregnated paper tapes. The single or multicore assemble in them enclosed in an impermeable metal sheath, and where necessary depending on installation conditions, the assembly is protected by steel armourings. Modern cable technology is still pursuing the above ideal, but today many other additional factors have also to be considered, as indicated in the following notes (dealing with oil impregnated paper insulated cables), which are divided into three main parts, the Ist dealing with cable design, the second part outlines modern manufacturing methods and the third section discusses installation requirements.
Cost EstimationPlant Capacity 1600 Mtrs/Day Land & Building (Area 1000 sq.mt.) Rs. 19 LacsPlant & Machinery Rs. 23 Lacs W.C. for 3 Months Rs. 91 Lacs Total Capital Investment Rs. 1.35 Cr. Rate of Return 29% Break Even Point 59%
PVC WIRE AND CABLES
2401. DETERGENT POWDER
(EXPORT ORIENTED UNIT) 47 Lacs 02. DETERGENT WASHING POWDER
(ARIEL TYPE) 93 Lacs 03. DETERGENT PASTE
(TEXTILE GRADE) 24 Lacs 04. DETERGENT (ANIONIC) 30 Lacs 05. DETERGENT CAKE & POWDER 6 Lacs 06. (IDET 10) DETERGENT
CONCENTRATE 24 Lacs 07. LIQUID DETERGENTS FOR WOOL 26 Lacs 08. LAUNDRY SOAP FROM
SOAP FLAKES 47 Lacs 09. LIQUID SOAP 25 Lacs 10. LIQUID TOILET CLEANER
(HARPIC TYPE) 63 Lacs11. METAL POLISH SOAP ——— 12. NEROL LAUNDRY SOAP 47 Lacs 13. NON-IONIC LIQUID DETERGENTS ——— 14. PHENYL 43 Lacs 15. SYNTHETIC DETERGENT
(BLUE POWDER) 25 Lacs 16. SCOURING POWDER CLEANING
POWDER (VIM TYPE) 28 Lacs 17. SCOURING BAR 69 Lacs 18. SOAP COATED PAPER 71 Lacs 19. SHAVING CREAM 25 Lacs 20. TOILET SOAP INDUSTRY
(SOAP FROM SOAP STOCK) 84 Lacs 21. TOILET SOAP FROM
SOAP NOODLES 68 Lacs 22. ULTRA MARINE BLUE (LIQUID) 81 Lacs 23. WASHING & LAUNDRY SOAP 50 Lacs 24. ZEOLITE-A (FOR DETERGENT) 4.47 Cr.
Each Project Report covers in this CD contains Introduction, Uses, Market, Process with Product
Formulae, Suppliers of Plant and Equipments, Cost Economics with Profitability Analysis, BEP,
Resources of Finance etc. Price of this CD containing all above 24 Project Reports is Rs. 18000/-. Payable fully in advance
through Draft/M.O. in favour of ENGINEERS INDIA RESEARCH INSTITUTE, DELHI. Delivery within 1
day. (To Order please dial : 98114-37895).
SOAP & DETERGENTS
(scouring Powder, Toilet Cleaner, Laundry Soap,
Detergants Cake & Powder, Toilet Soap,
Enzyme Based Detergant, Phanyl &
Soap Coated Paper) Rs. 18,000/- For All 24
Projects Reports In Cd.
PROJECT NAME PROJECT COST
Herbal Capsules is a new innovative concept, which are now being introduced in lieu of the conventional Gelatin Capsules. For the manufacture of Gelatin Capsules the raw material used Gelatin is from bones which is of animal orgin which in view of certain ethical and religiions considerations is acceptable to certain sect of people. So, the concept of Herbal Capsules is being promulgated in pharmaceutical preparation. The Herbal Capsules are redeemed from such ethos and invite a congenial acceptability by all. Being herbal in nature they ensure safty and no side e f f e c t s t o h u m a n s y s t e m a n y contraindicatious during the course of treatment for certain ailments. Their availability encompasses variegated shapes as of the conventional capsules prevelant in the market the common shapes being spherical also the range bigger. The capsules are intended for enclosing medicine ingredients meant for oral administration.
Cost EstimationPlant Capacity 200000 Nos./Day Land & Building (Area 2500 sq.mt.) Rs. 65 LPlant & Machinery Rs. 38 Lacs W.C. for 1 Months Rs. 6 Lacs Total Capital Investment Rs. 1.14 Cr. Rate of Return 35% Break Even Point 53%
HERBAL CAPSULES
0 9 8 1 1 4 3 7 8 9 5
For Any
Enquiry About These
ProjectsJust Call
4449, Nai Sarak, Main Road, Delhi-110 006 (India)Ph. : 91-11-23918117, 23916431Fax : 91-11-23916431, 23918117
E-Mail : [email protected], [email protected]
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 12 :-
Rs.
1150/-
Rs.
1900/-
1001. ACRYLIC SHEET AND
MOULDED PRODUCTS 2. AUDIO CASSETTES PARTS BY
INJECTION MOULDING 3. AUDIO CASSETTE ASSEMBLY
& RECORDING 4. AUTOMOBILE INJECTION
MOULD PLASTIC COMPT. 5. ABS GRANULES 6. AIR BUBBLE PACKAGING FILM 7. BALL PEN 8. BATH TUB (ACRYLIC) 9. BLOW MOULDED PLASTIC
CONTAINER 10. BLOW MOULDING MACHINE
FABRICATION 11. B.O.P.P. FILM 12. B.O.P.P SELF ADHESIVE TAPES 13. BLISTER FILM P.V.C 14. BALL POINT PEN, REFILLS & INK 15. COLOUR MASTER BATCHES
FOR VARIOUS PLASTICS 16. COMPACT DISK 17. DOUGH MOULDING
COMPOUND (DMC), BULK MOULDING COMPOUND (BMC), SHEET MOULDING COMPOUND (SMC)
18. DISPOSABLE PLASTIC CUPS, GLASSES ETC.
19. DISPOSABLE PLASTIC SYRINGES (STERILIZED)
20. DISCOUNT/CREDIT CARD 21. ELECTRIC SWITCHES, PLUGS,
SOCKETS ETC. 22. EVA (ETHYLENE VINYL
ACETATE) SHEET 23. EGG TRAYS FROM PLASTICS 24. EVA (ETHYLENE VINYL
ACETATE FOOT WEAR INJECT 25. EXPANDED CELLULAR
POLYETHYLENE SHEET 26. FIBER GLASS 27. FIBRE GLASS SHEETS 28. F R P PRODUCTS 29. H.D.P.E/P.P. BOX STRAPINGS 30. HDPE/PP SACKS (BAGS) 31. HDPE FISHING NET 32. H.D.P.E PIPES 33. HELMET 34. H.D.P.E. AND FITTING PIPES 35. INJECTION & BLOW MOULDED
PLASTIC PRODUCTS 36. INTRAVENOUS FLUID
PLASTIC BOTTLE 37. INJECTION MOULDED
PLASTIC BALLS 38. INJECTION MOULDING FOR
PLASTIC COMPONENTS WITH TOOL ROOM
39. LAMINATION OF CO-EXTRUSION MULTI LAYER FILM IN ROLL FORM
40. LAMINATION ON HDPE WOVEN CLOTHES
41. MULTI LAYER CO-EXTRUSION, 3 LAYER - FILM WITH LAMINATION & PRINTING
42. NYLON GRANULES FROM NYLON WASTE 43. NYLON NET FOR GIVING SHADE TO TEA
PLANT IN NURSERY
44. PET BOTTLES FROM PRE-FORM (CAPSULES)
45. PET GRANULES (DANA) 46. PLASTIC INJECTION
MOULDING PRODUCTS
PROFITABLE PLASTIC
POLYMERS AND ALLIED PROJECTS
(100 PROJECT REPORTS
IN CD
PROJECT NAME
47. PLASTIC BANGLES BY INJECTION MOULDING
48. PLASTIC MAT 49. PLASTIC MOULDED
FURNITURE 50. P.V.C. PIPES AND FITTINGS 51. PLASTIC FILMS AND SHEETS
WITH PRINTING (FLEXO AND ROTO) LDPE/HDPE/PP/HM/PVC
52. PLASTIC COLLAPSIBLE TUBES
53. PLASTIC GRANULES 54. PLASTIC GRANULES FROM
FRESH RESIN 55. PLASTIC (NYLON) NIWAR 56. PLASTIC BUTTONS BY
INJECTION MOULDING METHODS
57. PLASTIC ROPE 58. PLASTIC CORRUGATED
SHEET & BOXES 59. PLASTIC TOOTH PICK 60. P.V.C. FILMS 61. POLY-VINYL FLOORING 62. PVC LEATHER CLOTH 63. P.V.C. BATTERY SEPARATOR 64. POLYURETHANE FOAM
(P.U. FOAM) 65. PVC FOOT WEAR 66. PLASTIC TARPAULIN 67. PLASTIC MILK CRATE AND
PLASTIC FISH CRATE 68. POLYTHENE BAGS 69. POUCH MAKING AND
GRAVURE PRINTING 70. PLASTTIC SUTLI OR
POLYPROPYLENE SUTLI 71. POLYMER PENCIL 72. PLASTIC JERRY CANS 73. PVC EXTRUSION PROFILES
(WIRING CHANNELS) 74. POLY CARBONATE SHEET 75. PVC/PLASTICS (SOFT/RIGID)
FILMS/SHEET 76. POLYSTER FILM 77. POLY PACKS OF POLYETHENE
FILM 78. P.V.C. FLEXIBLE PIPES 79. PVC RESIN FROM CALCIUM
CARBIDE 80. PVC NON-WOVEN MAT 81. PLASTIC WATER STORAGE
TANKS (HDPE) (SINTEX TYPE) 82. POLYMERIC ROOFING FELT 83. P.V.C. CONDUIT PIPES 84. POLYSTER YARN FROM WASTE 85. PET PRE-FORM, PET BOTTLES
-CUM-MINERAL WATER 86. PVC WIRES AND CABLES 87. PVC COVER & FILES 88. POLYESTER ZIP FASTENERS 89. POLYPROPYLENE & MULTI
FILAMENT SPINNING YARN 90. PLASTIC TOYS 91. PLASTIC DOORS & WINDOWS 92. SPOONS (PLASTIC) 93. SYNTHETIC FELT (PLASTIC
BASED) USED IN PAPER MILL 94. SPORT SHOES (IMPORTED
AUTOMATIC PLANT) 95. THERMOCOLE BASED
DISPOSABLE GLASS, CUPS & PLATES
96. TEFLON - COATED - ELECTRIC CABLES
97. TOOTH BRUSH 98. THERMOCOLE
PROJECT NAME
Price of this Cd is Rs. 21000/- containing all above 100 Project Reports. Each Project Report covers Manufacturing Process,
Market, Manufacturers, Flowsheet, Formulae, Cost Economics, Land and
Building Required, Raw Materials required, Profitability, Resources of Finance, BEP,
List, Cost and Suppliers of Plant & Machinery and Raw Materials etc. Just
contact on 09811437895 to avail CD.
RS. 21,000/- FOR CD
Non-Coking Coal (steam coal) is heated in an oven for 36 hours when it is converted into coking coal lumps. Regarding coking of coal the two main types of coking procedures are beehive coking and co-products coking. Beehive coking is the primitive method. The beehive oven consist of beehive - shaped brick chamber provided with a charging hole at the done and a discharging hole in the circumference ofthe ower part of the wall. The coal is introduced through the hole in the top of the done and spread over the floor. The heat reaction in the oven is sufficient to start the distillation.The gases given off from the coal mix with the air entering at the top of the discharge door abd burn the heat of combustion is sufficient for pyrolysis and distillation.
Cost EstimationPlant Capacity 100 MT./Day Land & Building (Area 10 Acres) Rs. 2.13 Cr.Plant & Machinery Rs. 92 Lacs W.C. for 1 Months Rs. 77 Lacs Total Capital Investment Rs. 4.05 Cr. Rate of Return 48% Break Even Point 39%
NON-COKING COAL TO COKING COAL
Pyridine and derivatives of pyridine occur widely in nature as components of alkaloids, v i tamins and coenzymes. These components are of contuining interest to theore t i ca l , phys ica l o rgan ic and biochemistry. They have many commercial uses eg herbicides and pesticides pharmaceutical feed supplement,solvent and reagents and chemical for the polymer and textile industries. Pyridine is a hygroscopic colorless liquid with a characteristic unpleasant smell. The compound a tertiary amine is a somewhat stronger base than aniline and readily forms quaternary ammonium salts. Pyridine in the parent of a series of compounds that is important in medicinal agricultural and industrial chemistry. Although many polysubstituted pyridine compounds like heterocyclic compounds are synthesized with their functional groups present from acylic compounds most derivatives are prepared by manipulation of pyridine and its simple homologued in a mannr similar to the chemistry of the benzenoid aromatics. However the simple pyridine compound are prepared by cyclization of aliphatic raw material.
Cost EstimationLand & Building (Area 3000 sq.mt.) Rs. 66 LacsPlant & Machinery Rs. 70 Lacs W.C. for 1 Months Rs. 14 Lacs Total Capital Investment Rs. 1.62 Cr. Rate of Return 84% Break Even Point 30%
PYRIDINE & ITS DERIVATIVES
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 13 :-
Humic Acid is a bio-chemical which is a very complex mixture of organic constitents which have their counterpart in biological tissue of plants. It is a brown polymeric constituent of soils lignite and beat. It contains brownish-black pigment melanin and peat. Humic Acid acts as a chelating agent a growth stimulant and catalyst and buffer against harsh conditions in the soil affecting the plants. It unlocks and chelates major and minor nutrients for plant uptake. In the absence of chelates in the Soil, Iron, Zinc, Manganese, Copper and Magnesium are converted to insoluble hydroxides. It keep trace elements in solution available for growing plants. It buffers high and low pH’s to allow nutrient uptake to less than optimum conditions. Humic Acid has the ability to resist a change in the hydrogen ion concentration. Thus buffering capacity ranges between 5.5 and 6.5. It contains wide variety of major and trace elements several amino acid and has pH of not less than 7.0. The degradation and transformations of post-mortal plant and animal material to humic substance is also attributed to the transfrormation function. Humic substances have been found in materials that have undergone coalification such as peat lignites and lignites.
Cost EstimationLand & Building RENTED Plant & Machinery Rs. 38 Th. W.C. for 1 Months Rs. 74 Th. Total Capital Investment Rs. 1.15 Lac Rate of Return 88% Break Even Point 66%
HUMIC ACID
Manufacturing of steel tubes & pipes is, basically a Heavy Mechanical Engineering industry and is mostly produced in large scale. Mainly there are 1) Black & Galvenised welded tubes & pipes 2) ERW -Steel tubes and 3) Seamless Steel tubes. ERW steel tubes are chiefly used in bicycles, transformers, L.P. Boilers, furnitures industries etc. While seamless steel tubes are used in oil exploration, fertilizer, boiler & chemical industries. Normally, the plant capacity of Indian steel tube units ranges from 5,000 M.T. to 25,000 M.T. per annum. The industry of even smaller capacity is possible which can suit the S.S.I. parameters but the economy of scales is always there. The improving industrial climate, greater emphasis on oil exploration, power generation and the nuclear programme have improved prospects for the Indian steel pipes and tubes industry, despite some temporary difficulties created by official policy. It now manufacturers items like seamless tubes and speciality pipes for use in oil exploration and drilling, conveyance of petroleum and gas, the chemical and fertiliser industries, nuclear plants etc. a and more speciality products are on the cards.
Cost EstimationPlant Capacity 10 Ton./Day Land & Building (Area 1500 sq.mt.) Rs. 88 LacsPlant & Machinery Rs. 68 Lacs W.C. for 3 Months Rs. 1.86 Lacs Total Capital Investment Rs. 3.50 Cr. Rate of Return 26% Break Even Point 53%
OXYGEN LANCING PIPES
A dairy is a place for handling milk and milk products. Technology refers to the application of scientific knowledge for practical purposes. Dairy technology has been defined as that branch of dairy science which deals with the processing of milk and the manufacture of milk products on an industrial scale. In developed dairying countries such as the U.S.A., the year 1850 is seen as the dwiding line between form and factory scale production. Various factors contributed to this change in these countries, viz concentration of population in cities where jobs were plentiful, rapid industrialisation, improvement of transportation facilities, development of machines etc, whereas the rural areas were identified for milk production, the urban centres were selected for the location of milk processing plants and product manufacturing factories.
Cost EstimationPlant Capacity 10000 Ltr./Day Land & Building (Area 1.5 Acre) Rs. 1.05 Cr.Plant & Machinery Rs.18 Lacs W.C. for 1 Months Rs. 29 Lacs Total Capital Investment Rs. 1.61 Cr. Rate of Return 32% Break Even Point 47%
MILK PROCESSING PLANT (TONED/DOUBLE TONED MILK, CREAM, BUTTER MILK, BUTTER CREAM,
KHOYA, BUTTER, PANEER, GHEE
Xanthates are a class of organic salts formed by treatment of an alcohol with carbon disulphide in the presence of an alkali. The term is derived from the Greek workd Xanthos or “Yellow” in reference to the compound potassium ethyl Xanthate C2H5OCS2K which gives a yellow precipitate when combined with copper sulphate. The most important group of Xanthates are the sodium salts produced from cellulose. These materials are spun to the synthetic fibre rayon or processed to the transparent film cellophane. The xanthates of some low molecular weight alcohols are used as floatation agents for the concentration of ores.
Cost EstimationPlant Capacity 1 MT./Day Land & Building (Area 1000 sq.mt.) Rs. 24 LacsPlant & Machinery Rs. 24 Lacs W.C. for 1 Months Rs. 14 Lacs Total Capital Investment Rs. 68 Lacs Rate of Return 55% Break Even Point 41%
SODIUM ISOPROPYL XANTHATE
Magnesium does not occur free in nature but its compounds are widely distributed.Its imported minerals are magnesite MgCO3, Dolomite MgCO3, Carnallite Kcl.MgCl2-6H2O, Asbestos CaMg3 (Sio3)4. The term Dolomite is referred to commercially as rocks containing the minerals dolomite calcite and magnesite. Magnesium Hydroxide Mg(OH)2 can be manufactured from dolomite Magnesium Hydroxide is a white powder almost insoluble in water and alcohol.
Cost EstimationPlant Capacity 2 MT./Day Land & Building (Area 2000 sq.mt.) Rs. 46 LacsPlant & Machinery Rs. 30 Lacs W.C. for 1 Months Rs. 38 Lacs Total Capital Investment Rs. 1.18 Cr. Rate of Return 87% Break Even Point 27%
MAGNESIUM HYDROXIDE FROM DOLOMITE
The great importance of the industrial gas, oxygen is due to the usefulness of the acetylene torch for steel welding and steel cutting, and for the welding of other metals, to lesser degree to the oxyhydrogen flame. Oxygen gas in the breathing apparatus for a visitors at high altitudes and for oxygentents in hospitals is a high altitudes and for oxygentents in hospitals is a more recent development. An extension of of the use of oxygen lies in the increased intensity and speed of reactions brought about by oxygen enriched air instead of ordinary air; the reduction of the cycle time so achieved in chemical or metallurgical process permits a greater yield per volume of equipment, and brings about lower costs. Oxygen as a raw mater ial for synthesizing chemical compounds is in daily use (ethylene oxide, sodium peroxide). Liquid oxygen mixed with
Cost EstimationLand & Building (Area 2 Acres) Rs. 1.55 Cr.Plant & Machinery Rs. 2.85 Cr. W.C. for 1 Months Rs. 13 Lacs Total Capital Investment Rs. 8.17 Cr. Rate of Return 37% Break Even Point 43%
OXYGEN CARBON DIOXIDE AND ARGON GAS
MODERN
TECHNOLOGY OF
NON FERROUS
METALS AND
METAL
EXTRACTION
TECHNOLOGY OF
PRODUCTSFROM
WASTES(INDUSTRIAL,
AGRICULTURE, MEDICAL,
MUNICIPALITY, ORGANIC &
BIOLOGICAL)
Rs. 900/-Book your copy today.
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 14 :-
Rs. 1100/-2011 Edition
551. ACRYLIC SHEETS 36 Lacs 2. ACTIVATED CARBON FROM SAW DUST,
RICE HUSK & COCONUT SHELL 77 Lacs 3. ACTIVATED CARBON FROM WOOD 69 Lacs 4. BIO FERTILISERS 58 Lacs 5. BEES WAX REFINING & BLEACHING 23 Lacs 6. BIOCOAL BRIQUETTES FROM
AGRICULTURE CELLULOSIC WASTE 53 Lacs 7. FUEL BRIQUETTES FROM
AGRO WASTE 37 Lacs 8. CAFFEINE FROM TEA WASTE 1.12 Cr. 9. CARPET FROM COTTON WAST 2.79 Cr.10. COIR PITH 1.49 Cr. 11. CEMENT FROM RICE HUSK 2.84 Cr.12. COTTON YARN 1.57 Cr. 13. CRUDE OIL BLEACHING
FOR PETROLEUM JELLY 54 Lacs 14. FURFURAL 11.46 Cr.15. FATTY ACID FROM WASTE VEGETABLE
———16. GOBAR GAS PLANT 10 Lacs 17. HAND MADE PAPER 1.04 Cr.18. HARD BOARD FROM RICE HUSK 33 Lacs 19. KRAFT PAPER BY WASTE
CARTON BOX 1.43 Cr. 20. KRAFT PAPER FROM
WASTE PAPER 3.57 Cr.21. MICROCRYSTALLINE WAX 3.25 Cr.22. OXALIC ACID FROM RICE HUSK 95 Lacs 23. OSSEIN AND GELATINE 2.44 Cr.24. PAPER WASTE RECYLING PLANT 3.62 Cr. 25. PARTICLE BOARD 1.39 Cr. 26. PECTIN FROM MANGO PEELS 81 Lacs 27. POLYSTER YARN FROM WASTE 42 Lacs 28. POWER PLANT 10.52 Cr.29. POWER PLANT (HYDRO BASED) 1.78 Cr. 30. PLASTIC GRANULES 7.97 Cr.31. PAPER CONES & TUBES 40 Lacs 32. PARAFFIN WAX FROM SLACK WAX 6.81 Cr.33. PAPER FROM RICE
HUSK/WHEAT HUSK 2.63 Cr.34. RECYCLING OF WASTE CELLULOSE
ACETATE INTO CELL. ACETATE SHEETS 1.58 Cr.
35. RUBBER RECLAIMING 2.34 Cr.36. RE-REFINING OF USED
ENGINE OIL 25 Lacs 37. RECLAMATION OF USED
BLEACHING EARTH 88 Lacs 38. RECOVERY OF LEAD FROM DISPOSED
LEAD ACID BATTERIES 1.52 Cr.39. RECOVERY OF GOLD FROM P.C.B
& OTHER ELECTRONIC WASTE 41 Lacs 40. RE-CONDITIONING OF
PICTURE TUBE 38 Lacs 41. RECONDITIONING OF
FLUOROSCENT TUBE 17 Lacs 42. RUBBER POWDER 23 Lacs 43. RECLAMATION OF NICKEL FROM
SPENT CATALYST OF VANASPATI INDUSTRIES 88 Lacs
44. RUBBER GOODS BY WASTE RUBBER 29 Lacs
45. RECOVERY OF SILVER NITRATE FROM PHOTOGRAPHIC WASTE FIXER ———-
46. SILVER EXTRACTION FROM WASTE HYPO SOLUTION X-RAY FILM AND CINEMA FILM 7 Lacs
47. SILICON FROM RICE HUSK 72 Lacs 48. SECONDARY LEAD EXTRACTION FROM
SCRAP BATTERY PLATES, PIPE, SHEET 5.10 Cr.
49. SILK WASTE PROCESSING & SPINNING ———
50. TREAD RUBBER 48 Lacs 51. TOLUENE & SBP FROM
CRUD NAPTHA 18.21 Cr.52. VODKA 2.30 Cr. 53. VERMI-COMPOSTING 3.20 Cr. 54. ZINC METAL FROM ZINC ASH 1.26 Cr.55. ZINC & COPPER SULPHATE
FROM BRASS ASH 1.16 Cr.Each Project Report covers in this CD contains
Introduction, Uses, Market, Process with Product Formulae, Suppliers of Plant and Equipments, Cost
Economics with Profitability Analysis, BEP, Resources of Finance etc.
Price of this CD containing all above 55 Project Reports is Rs. 18000/- or US $ 650/-. Payable fully in advance through Draft/M.O. in favour of ENGINEERS
INDIA RESEARCH INSTITUTE, DELHI. Delivery within 1 day. (To Order please dial : 98114-37895).
55 PROFITABLE PRODUCTS
FROM AGRO & OTHER
INDUSTRIAL WASTE IN CD
RS. 18,000/- OR US$ 650/-
PROJECT NAME PROJECT COST
The Chinese herb mixture “Ma Huang” has been used empirically by native physicians for more than 5000 years. “Ma Huang”, which contains ophedrine, has also been wideley used in U.S.S.R.in the treatment of various disorders. While the mydriatic activity of the alkaloid ephedrine was first demonstrated in 1887 by Miura, the use of ephedrine as a mydriatic enjoyed only a passing vogue. International interest in the drug was stimulated in 1924 by the classical investigations of Chen and Schmidt, who reported its cardiovascular effects, its similarity to epinephrine, and its absorption from the intestinal tract. Ephedrine (1-phenyl-2-methylaminopropanol) (C6 H5 CH COH) CH (NH. CH3). CH3 is optically active (Levorotatory) form, which is white to colourless granules, pieces or crystals, hygroscopic in nature and gradually decomposes on exposure to light. It is soluble in water, alcohol, ether, chloroform and oils. Its major use in medicine is as bronchodilator.
Cost EstimationPlant Capacity 75 Kgs/Day Land & Building (Area 500 sq.mt.) Rs. 13 LacsPlant & Machinery Rs. 6 Lacs W.C. for 3 Months Rs. 15 Lacs Total Capital Investment Rs. 35 Lacs Rate of Return 32% Break Even Point 58%
EPHEDRINE HYDROCHLORIDE
Testing Laboratory is an unit which is established in the industrial sectors, in Educational Institutions, Engineering Colleges and in Commercial establishments to serve the different Industrial & Medical sector. The Laboratory becomes as sophisticated as it possess the number and quantity of bulk sophisticated instruments such like ultraviolet spectro photometer, Micrometer vertical Laminer flow etc. Laboratory is key House where a lot of ana ly t i ca l tes t chemica l ana lys i s identification and detections of unknown elements etc. are carried out most scientifically with a view of invention and research. By performing the number of trails and observations, the scientists are able to assess both quantitatively and qualitatively the merits of most economical as feasible scientific procedures and techniques which ultimately serves as stepping stone to accomplish higher objectives in research work.
Cost EstimationLand & Building (Area 500 sq.mt.) Rs. 35 LacsPlant & Machinery Rs. 14 Lacs W.C. for 1 Months Rs. 3 Lacs Total Capital Investment Rs. 57 Lacs Rate of Return 57% Break Even Point 41%
TESTING LAB
Elevators are the most important material handling equipment and are mainly used for handling raw material and finished product in process industrries. The market of the elevator is related to the scope and prospect of process industries like chemical, mining, fertilizers, coal, etc. At present there are few manufacture in organised sector and there is a good scope for new investment.
Cost EstimationPlant Capacity 300 Nos./Annum Land & Building (Area 5000 sq.mt.) Rs. 2.20 Cr.Plant & Machinery Rs. 32 Lacs W.C. for 3 Months Rs. 56 Lacs Total Capital Investment Rs. 3.13 Cr. Rate of Return 36% Break Even Point 41%
ELEVATORS
Cost EstimationPlant Capacity 40 Nos./Day Land & Building (Area 1500 sq.mt.)Rs. 99 LacsPlant & Machinery Rs. 5 Lacs W.C. for 3 Months Rs. 14 Lacs Total Capital Investment Rs. 1.23 Cr. Rate of Return 34% Break Even Point 46%
FIRE EXTINGUISHERS
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 15 :-
The book Aloe Vera Cultivation, Processings, Formulations and Manufacturing Technology covers Introduction, Cultivation, Aloe vera Leaf Processor, Aloe vera Gel Extracting Apparatus, Aloe vera Plant Gel Separator, Aloeferon, Manufacturing and its Application, Stabilized Aloe Vera Gel, Hypoallergenic Stabilized, Aloe vera Gel Toothpaste, Protective Hand Lotion of Aloe vera Gel and Vitamin E-Gel, Cosmetic Facial Preparation Containing Aloe vera, Cosmic Lotion, Cosmetic Composition, Conditioner that provides skin like an Angel, Hair Cleanser, Hair Products, Dyeing Composition of Hair, Therapeutic shampoo Composition, Whitening Compound, Organic Toothpaste, Shaving Composition, Detergent Compositions, Disinfectant Cleaning Composition, Slimming Soap, cleansing Composition with Orange Oil, Aloe vera Ointment, Therapeutic Composition for Treatment of Mucositis and Mucosal Disorder, Herbal Composition for Treating Muscle Aches and Joint Pain, Immunomodulatory Polysaccharides from Aloe Softening Composition, Antimicrobial Agents Isolated from Aloe Vera, Antioxidant Compositions for the Eye, Burn Treatment, Decongestant Composition Containing Aloe vera, Extracts of Aloe for Oral Administration, Herbal Formulation, Nasal Spray, Non-irritating Antiperspirant, Non-Toxic Mucosal Disinfectant, Aloe vera Opthalmic Solution, Aloe Pectins and its Pharmaceutical Composition, Scar Reducing and Massage Emollients, Skin Therapeutic Mixture, Topical Analgesic Formulation, Topical Composition for Relief of Pain and Minor Skin Irritations,Transdermal Formulation, Herbal Formulation Useful for Treatment of Skin Disorders, Neutraceutical Treatments for Diabetic and Non-Diabetic Wound healing, Therapeutic Composition for Treatment of Arthritis and other Afflictions, Therapeutic Cream, Wound Healing, Clear Juice from the Leaves of the Aloe vera Plant, Drink Containing Mucitaginous Polysacchardes, Healthy Baby Beverage, Nutritional Composition, Aloe vera Glove, Aloe vera Processed Leather and Leather Gloves, Garments, Shoes and Sandals, Gloves Containing Dry Aloe Powdered, Treating Textiles and Articles of clothing, Additives for Sanitary Napkins, Insect Repellent, Uses of Denture Adhesive Containing Aloe Extract, Adhesive Agent and its use, Scale Inhibitor from Aloe, Coating containing Denatured Aloe vera.
Aloe Vera Cultivation,
Processings, Formulations
and Manufacturing
Technology
By : Dr. H. Panda2011-12 Edition
Rs. 2500/-
India is marching ahead with its populace-men, women and children working almost round the clock to take it forward to the advanced status by the turn of the century. Time has come when like western countries India’s population too has to increasingly rely on Frozen Food products to serve and eat hygienically cooked & well preserved food. Modern technology has also brought in better more hygienic and more economical ways of cooking and preserving food. New companies are entering in the market with new products and more and more companies are diversifying and expanding faster win the processed food items than in their traditional products. Curry meals Indian Bread (Frozen) Indian snacks, sweets & Dessorts are gaining enormous eminence in modern era. It is consumed by the all strata of society in an appreciable quantity. These foods also serve the ease of their availability to people during outing, in picnics etc, where they relish these food. The future scope of these food is very Bright.
Cost EstimationPlant Capacity 4000 KGS/Day Land & Building Rs. 24.97 Cr.Plant & Machinery Rs. 3.57 Cr. W.C. for 1 Months Rs. 89 Lacs Total Capital Investment Rs. 29.81 Cr. Rate of Return 43% Break Even Point 32%
FROZEN FOOD PRODUCTS
Alpha Amino Acetic Acid (Glycine) is a non essential amino acid and is available in white very sweet odorless crystal m.p.-232-236oC,specific gravity -1.1607. It is generally occurs in many protein and is especially abundant in silk fibroin gelation and sugar cane as a principal amino acid in sugar cane. The main uses and application of Alpha Amino Acetic Acid are in oraganic synthesis, medicines, biochemical research, feed additives, nutrient and dieltary supplemant and as a buffering agent. All the amino acids except glycine have two optically active isomers symbolized by D or L before their nanes. The history of amino acid discoveries is closely related to advances in analytical methods initially, quantitative and qualitative analysis depended exclusively upon crystallization from protein hydrolysates.
Cost EstimationPlant Capacity 2 MT./Day Land & Building (Area 1000 sq.mt.) Rs. 59 LacsPlant & Machinery Rs. 26 Lacs W.C. for 1 Months Rs. 39 Lacs Total Capital Investment Rs. 1.29 Cr. Rate of Return 70% Break Even Point 31%
(ALPHA) AMINO ACETIC ACID
Among various kinds of adhesives Starch Based Adhesives constitute their paramount significance. These are generally clasified according to the processing they receive prior to compounding them into adhesives. These are vegetable adhesives. However there are innumerable variety of starch adhesives depending upon their origin and processing condition.
Cost EstimationPlant Capacity 2 Ton./Day Land & Building (Area 500 sq.mt.) Rs. 13 LacsPlant & Machinery Rs. 7 Lacs W.C. for 1 Months Rs. 11 Lacs Total Capital Investment Rs. 32 Lacs Rate of Return 91% Break Even Point 29%
ADHESIVE FOR PAPER BOARD
Iso -borneol is a important product having wide application in perfumery and chemical esters. The demand of hte product is entirely related to the growth of end user industries. At present there are few manufacture of iso-borneol in india and the demand of the products is increasing day by day. For the economic production of iso - borneol it would be necessary to select a cheap raw material. Howeever i t is possible to import pinene/camphene at economic from U.S.A. So as long as pinene is available at economic rate manufacture of iso - borneol will be must profitable.
Cost EstimationPlant Capacity 500 KGS/Day Land & Building (Area 1000 sq.mt.) Rs. 44 LacsPlant & Machinery Rs. 16 Lacs W.C. for 1 Months Rs. 18 Lacs Total Capital Investment Rs. 81 Lacs Rate of Return 82% Break Even Point 28%
ISO - BORNEOL
In the modern era the packaging and printing industries are playing a vital role for Packaging of various commodities for customer appeal and acceptancence in all over world for marketing of various products. We are proposing to manufacture mono cartons, of various sizes for our various customers.
Cost EstimationPlant Capacity 3.50 Ton./Day Land & Building (Area 1012.5 Cr.) Rs. 87 LacsPlant & Machinery Rs. 62 Lacs W.C. for 1 Months Rs. 35 Lacs Total Capital Investment Rs. 1.87 Cr. Rate of Return 56% Break Even Point 32%
MONO CARTONS WITH PRINTING
The materials now available for packaging are paper and paper products, metal containers and foils, glass, plastics-rigid and flexible, cellulosic films, textiles including jute, woven plastics and wood. Among the packaging materials, paper and paper based products continue to occupy a predominent place. Paper based materials used for packaging include bleached and unbleached kraft, corrugated and solid fibre boards, and a large variety of conveted items like wax coated, plastic coated, bitumen coated etc. Corrugated and solid fibre board boxes have replaced the conventional wooden boxes as transport containers because of thier light weight and satisfactory strength. There are, however, several areas in which this sector is laggin behind the developed countries, They include mainly production of parchment paper for use in packaging of biscuits etc. Sack kraft paper and high strength kraft for producing corrugated fibre board of good strength characteristics.
Cost EstimationPlant Capacity 2650 KGS/Day Land & Build (Area 1012.50 sq.mt.) Rs. 82 LacsPlant & Machinery Rs. 11 Lacs W.C. for 1 Months Rs. 14 Lacs Total Capital Investment Rs. 1.12 Cr. Rate of Return 62% Break Even Point 32%
PRINTED CORRUGATED BOXES
The state of a country’s iron and steel industry products an index as its industrial progress. A universaly aecepteal yardstate formeasuring a cointerators level of eaenoine elevelopment is is per capita onsumption of steel. Judg by the yordexick the depressing fact remains that. India is among the countries with the loeoest per capta consunpoeon of steel in the world, with only 14 bg Developed cournes such as sweeden, west Germany Japan and U.S.A. hous high percapita consumption figeres. The histary of iron & steel making in India goes bade to over 2500 years, making India of of the carliest usess of iron and sted in the world. In ancient times, India has ettained a remarkafly high degree of skill in iron of iron products smelting and the making.
Cost EstimationPlant Capacity 50 MT./Day Land & Building (Area 10 Acres) Rs. 10 Cr.Plant & Machinery Rs. 3.24 Cr. W.C. for 3 Months Rs. 7.19 Cr. Total Capital Investment Rs. 21.10 Cr. Rate of Return 32% Break Even Point 39%
SPONGE IRON WITH PELLETIZATION PLANT
YOU CAN ESTABLISH YOUR OWN INDUSTRY
YOU CAN ESTABLISH YOUR OWN INDUSTRY
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 16 :-
Fung ic ides fa l l i n to two gene ra l classifications. Agricultural and industrial. Fungicides for plants act by direct contact and often injume the host as well as the fungus. Fungi are parasitic plants comprising of molds, muldews, rusts, smuts, mushrooms, and allied forms that are capable of destroying higher plants. They may attack seeds, the growing plant and plant materials. Fungicides are used as dusts sprays or pastes for destroying pathogen on dormant plant parts disinfection or disinfectation) . They also give protective cover to plant parts to prevent subsequent infection. The quality of a fungincide is therefore judged by the extent to which these twin objectives are achieved. The chemical control of plant deseases is moderately expensive and to achieve good results it should be carried out according to the advice tendered by technical experts of this field. The treatment should be given at the right time and with an approved fungicide.
Cost EstimationPlant Capacity 2500 KGS/Day Land & Building (Area 2000 sq.mt.) Rs. 95 LacsPlant & Machinery Rs. 39 Lacs W.C. for 3 Months Rs. 1.27 Cr. Total Capital Investment Rs. 2.67 Cr. Rate of Return 68% Break Even Point 27%
COPPER OXCHLORIDE
Calcium Fluoride Ca,F2 is a most versatile Chemical which is Precisely used in the manufacture of special glasses,enamels & welding flux, etc. There are two convenient method for its manufacturing:- 1. By powdering pure fluoride or fluorspar. 2. By the interaction of soluble Calcium Salt Sodium Fluoride. At present there are few manufacturers of clacium fluoride in organised sector and the current production is not sufficient to meet the current demand. Calcium fluoride is a white powder and occur in nature as a fluorite.
Cost EstimationPlant Capacity 2 MT./Day Land & Building (Area 1500 sq.mt.)Rs. 70 LacsPlant & Machinery Rs. 14 Lacs W.C. for 1 Months Rs. 14 Lacs Total Capital Investment Rs. 1.01 Cr. Rate of Return 56% Break Even Point 40%
CALCIUM FLUORIDE
Cold storage industry is a very important and essential industry. In India, fruits and vegetables are produced in plenty. A large number of fruits and vegetables are exported to other countries and even in India itself fruits and vegetables are transported from one place to another. This transportation business takes some time. So, it is desirable that fruits should be kept at a place where they can remain safe, other wise a lot of its will be wasted. For this purpose, Cold Storage is used. Cold Storage is a special kind of room the temperature of which is kept very cold with the help of machines and instruments. The temperature is maintained low with the help of precision instruments. In deciding the scale of a cold storage plant, all the external condition locational conditions stored, object etc. must be considered. When the scale of plant is larger however running costs would generally be less and automation would become more exact.
Cost EstimationPlant Capacity 5000 MT./Annum Land & Building (Area 3000 sq.mt.) Rs. 2.16 Cr.Plant & Machinery Rs. 53 Lacs W.C. for 2 Months Rs. 17 Lacs Total Capital Investment Rs. 3.05 Cr. Rate of Return 15% Break Even Point 70%
COLD STORAGE
While PET bottle development was proceeding in the US, a large manufacturer of injection moulding machines in Japan, was leading a project to develop a machine to make biaxially oriented PP (polypropylene) containers. They recognized that the prototype machine could be used to produce the new PET bottles and, in December 1975, the One-stage ASB-150 injection stretch blow moulding machine for making the new biaxial oriented PET bottles was unveiled. All one-stage injection stretch blow moulding machines derived from this original Stretch Blow design are referred to as classic one-stage machines, as the concept has long since been extended into other PET developments. The classic one-stage machines design is extremely versatile in that the same basic machine design can be used to make a wide variety of bottles and jars in all shapes and sizes, which was the standard single-stage machine in the early years, had eight cavities for 1.5 litre bottles.
Cost EstimationPlant Capacity 120000 Bottles/Day Land & Building (Area 2500 sq.mt.) RENTED Plant & Machinery Rs. 1.16 Cr. W.C. for 1 Months Rs. 51 Lacs Total Capital Investment Rs. 1.82 Cr. Rate of Return 24% Break Even Point 69%
PET BOTTLES FOR PHARMACEUTICAL INDUSTRY ON SINGLE STAGE BLOW
MOULDING MACHINE
Sugar is a universal sweetening agent and sugar - cane is the primary age - old source of it. Sugar cane is a very important industrial crop, accounting for about 60% of sugar production in the world. From the times immemorial the word “sugar” is being used variously to express delight as well as distrust sarcastically. Sugar has been used in human diet through the functions of pancreas, depending on the quantity6 of sugar consumed. It is must for human diet when taken directly or indirectly through various carbohydrate containing food stuffs. Sugar as sucrose is important for energy and metabolic activities. The main raw material for sugar production, i.e. sugarcane grows widely and efforts are constantly being made to bring more area under cultivation. The process chemicals required are also available. Sugarcane is grown in tropical and sub-tropical countries. Another sugar yielding material, the best is grown in temperate regions. The best is an important raw material in many European Countries. Of the total sugar production in the world, cane sugar constitutes nearly 55 per cent. Two third of the total cane sugar comes from Cuba, Brazil India, Australia, Mexico, China, Phillipines and U.S.A., South Africa, Argentina, Mauritius and Egypt are also important cane producers.
Cost EstimationPlant Capacity 3000 TCD/Day Land & Building (Area 70 Acres) Rs. 1610 LacsPlant & Machinery Rs. 400 Lacs W.C. for 3 Months Rs. 4753 Lacs Total Capital Investment Rs. 6863 Lacs Rate of Return 66% Break Even Point 20%
SUGAR PLANT
Modern Technology
of Non Ferrous
Metals andMetal
Extraction
Rs. 1100/-
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 17 :-
The foundation of the modern Indian pharmaceutical Industry was laid at the start of the current century when in 1901, a small factory known as the Bengal Chemical & Pharmaceutical works was established in Kolkata. Though the two world Wars gave a Phillip to the development of industry, the progress made under British rule was not significant except the British introduced into this country the allopathic system of medicine. The country depended largely for its requirements on U.K., France and Germany. The development of Indian Drugs and pharmaceuticals Industry was not commonsurate with the size of this country and the growing needs of people, when Indian embarked on its planned economic expansion industry has been substantial and many sides with the result that it has becomes one of the leading industries. India is now producing a larger quantity of varied pharmaceuticals products. In 1948, the sale of pharmaceuticals products. In 1948, the sale of pharmaceutical products amounted to just Rs. 100 million. By 1954 the figure had rised to Rs. 540 million and by 1960 to Rs. 700 million. The figure stood at between Rs. 1500 million in 1965 and Rs. 4000 millions in 1975, Rs. 12000 millions in 1980 and above Rs. 18,500 millions presently.
Cost EstimationPlant Capacity 4000 Nos./Day Land & Building (Area 6000 sq.mt.) Rs. 2.13 Cr.Plant & Machinery Rs. 53 Lacs W.C. for 3 Months Rs. 1.29 Cr. Total Capital Investment Rs. 4.02 Cr. Rate of Return 136% Break Even Point 27%
PHARMACEUTICAL UNIT WITH CHEMICALS TABLET, CAPSULES,
SYRUPS, LOTION ETC.
Lacquers in general are solutions of resins in organic solvents. Which harden only as a result of the evaporation of the solvent. Lacquer is used for protective or decorative coating that dries primarily by evaporation of solvent with no molecular change occuring e.g . Oxidat ion or polymerizat ion. Polyurethane (PU) Lacquer (water based) in liquid form for electrophoretic coating application on metal plates is finding a wide field of applicability in modern times. The speciality of this sort of lacquer coating is a very good uniformity of deposition/coating on the metal surface.
Cost EstimationPlant Capacity 1000 KGS/Day Land & Building (Area 750 sq.mt.) Rs. 21 LacsPlant & Machinery Rs. 34 Lacs W.C. for 1 Months Rs. 27 Lacs Total Capital Investment Rs. 91 Lacs Rate of Return 115% Break Even Point 25%
POLYURETHANE (PU) LACQUER
Jewellery casting investment powder is a well organised industry to cater jewellery manufacture for jewellery casting which is a important lucrative business to produce precision jewellery. Investment casting is a metal csting process which employ an expandable pattern and one piece non metallic mold and elimate the parting line and reduce the machining cost. All metalls manely ferrous and non ferrous can be casted by this process and is most suitable for expensive hard and high strength metals and alloys which are difficult to machine. The number of unit engage in this field are negligible. Hence in view of the obove there is a immense scope for setting up new units in the small scale sector.
Cost EstimationPlant Capacity 500 KGS/Day Land & Building (Area 500 sq.mt.) Rs. 24 LacsPlant & Machinery Rs. 4 Lacs W.C. for 1 Months Rs. 2 Lacs Total Capital Investment Rs. 32 Lacs Rate of Return 35% Break Even Point 52%
JEWELLERY CASTING INVESTMENT POWDER
The pineapple is botanically known as Ananas Comusus. It is one of the most important fruits of the eastern region especially in Assam, Tripura, Darjeeling, Nagaland etc. The fruit is delicious when fully ripe, and is very rich in Vitamin A, B and C and mineral salts. It is not only used as a fresh fruit, but also preserved as canned pineapple rings or slices, jam, squash, etc. Pineapple products are in great demand and are sent to the soil and climate. The pineaple is rather exacting in its requirement of soil and climate. The sweetness of the fruit depends on these factors. The soils most suitable for pineapple are the well-drained loam or sandy loam soils of the plains and laterite soils of the hills, which are rich in organic matter. It needs an acid soil of pH 4.5 to 5. It grows both in tropical and subtropical climates up to an altitude of about 3,000 feet, with the temperature ranging from 60o to 90oF. An altiutde up to 800 feet might be considered safe for its cultivation. It requires a rainfall varying from 30 to 200 inches annually, particularly where the crop is dependent on natural precipitation.
Cost EstimationPlant Capacity 2000 KGS/Day Land & Building (Area 1000 sq.mt.) Rs. 47 LacsPlant & Machinery Rs. 31 Lacs W.C. for 1 Months Rs. 18 Lacs Total Capital Investment Rs. 1 Cr. Rate of Return 37% Break Even Point 50%
PINE APPLE PULP & JUICE
Sugar is a universal sweetening agent and sugar - cane is the primary age - old source of it. Sugar cane is a very important industrial crop, accounting for about 60% of sugar production in the world. From the times immemorial the word “sugar” is being used variously to express delight as well as distrust sarcastically. Sugar has been used in human diet through the functions of pancreas, depending on the quantity of sugar consumed. It is must for human diet when taken directly or indirectly through various carbohydrate containing food stuffs. Sugar as sucrose is important for energy and metabolic activities. When sugar was prepared from sugar cane in the beginning cannot be definitely stated, but brown sugar or gur (Jaggery) was the first known form of sugar manufactured from sugar cane as well as from wild date palm (phonnix sulvestris), palmyra palm (Borassus Flapellifar), toddy palm (Caryota urens) and other palms contains 12-14% sugar in their sap tapped for the purposes.
Cost EstimationPlant Capacity 300 Ton/Day Land & Building (Area 2.5 Acres) Rs. 2.05 Cr.Plant & Machinery Rs. 1.35 Cr. W.C. for 3 Months Rs. 6.26 Cr. Total Capital Investment Rs. 9.80 Cr. Rate of Return 33%
MINI SUGAR PLANT BY VACUUM SYSTEM
Sugar is a universal sweetening agent and sugar - cane is the primary age - old source of it. Sugar cane is a very important industrial crop, accounting for about 60% of sugar production in the world. From the times immemorial the word “sugar” is being used variously to express delight as well as distrust sarcastically. Sugar has been used in human diet through the functions of pancreas, depending on the quantity of sugar consumed. It is must for human diet when taken directly or indirectly through various carbohydrate containing food stuffs. Sugar as sucrose is important for energy and metabolic activities. When sugar was prepared from sugar cane in the beginning cannot be definitely stated, but brown sugar or gur (Jaggery) was the first known form of sugar manufactured from sugar cane as well as from wild date palm (phonnix sulvestris), palmyra palm (Borassus Flapellifar), toddy palm (Caryota urens) and other palms contains 12-14% sugar in their sap tapped for the purposes.
Cost EstimationPlant Capacity 300 Ton/Day Land & Building (Area 2.5 Acres) Rs. 2.05 Cr.Plant & Machinery Rs. 1.35 Cr. W.C. for 3 Months Rs. 6.26 Cr. Total Capital Investment Rs. 9.80 Cr. Rate of Return 33% Break Even Point 38%
MINI SUGAR PLANT BY VACUUM SYSTEM
For any Enquiry about these projectsJust Call
0 9 8 1 1 4 3 7 8 9 5
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 18 :-
Steel is a generic name for a group of ferrous metals which due to their abundance durability versatility and low cost are most useful metallic material known to mankind. Re-rooling Mills produce various types of rolled section such as Round, Tor Rod Angles Z section among these products M.S.Round Rod Tor Steel are the most popular product any construction works where there is civil or structural require rolled section like round, Tor Steel, etc. Steel in the form of Bars/Tor/Rod is used in the construction of buildings. The principle operation involves heating of billets/ingots to proper counters, dimension and shape.
Cost EstimationPlant Capacity 15 MT./Day Land & Building (Area 1.5 Acre) Rs. 1.30 Cr.Plant & Machinery Rs. 1.03 Cr. W.C. for 3 Months Rs. 3.98 Cr. Total Capital Investment Rs. 6.48 Cr. Rate of Return 52% Break Even Point 34%
RE-ROLLING MILL (REINFORCEMENT
AND STRUCTURAL MEMBERS)
Handicraft Industry is cottage Industry giving employment to many thousands of artisans and craftmens also employing thousands of unskilled workers supporting the packing and finishing process. This Industry promoted by EXPORT PROMOTION COUNCIL FOR HANDICRAFTS UNDER THE AEGIES OF DEVELOPMENT COMMISSIONER OF HANDICRAFT AND THE GOVENRMENT OF INDIA. In recent years importance of Handicrafts,imitation and costume jewellery has acquired prominance over their monetary value, it is now valued for their delicate design workmanship. Various types of imitation and costume jewelleries are being made through out the country. These are produced in various good attractive designs and colours. It is manufactured with b a s e m e t a l s a n d a l l o y s l i k e aluminium,brass,lead, tin etc by fixing beads or minakari work. Particularly costume jewellery is manufactured by attaching a cluster of beads (horn, glass, stone, bone, plastic, wool) either categorically or mixed with the help of plastic (nylon of P.P.) threads a s r e q u i r e d q u a l i t y, c o l o u r a n d designs.These jewelleries are produced in the forms of necklace, ear-rings, ear-top, brooches, chain, bangles etc.
Cost EstimationPlant Capacity 20 KGS/Day IMITATION JEWELLERY 30 KGS/Day COSTUME
JEWELLERYLand & Building (Area 4050 sq.mt.) Rs. 2.63 Cr.Plant & Machinery Rs. 8 Lacs W.C. for 3 Months Rs. 64 Lacs Total Capital Investment Rs. 3.40 Cr. Rate of Return 42% Break Even Point 39%
ARTIFICIAL/ IMITATION/ COSTUME JEWELLERY AND
HANDICRAFTS OF ALL TYPES
Car Seat Covers and related products are most vibrant and demandable Automobile accessories. The sizes and Dimension is depends upon the different cars available in the market and is manufacture in different sizes. PVC leather Cloth/Rexine is also known as artificial leather which is becoming popular all over the world because of shortage of actual leather and high cost of hte same. Artificial leather is specially suitables for Car Seat red related products. IT is water repellent and is chemiclly inert. It is much cleaner oth in producttion and in use eside being competive in price. Present inductions show that artificial leather goods viz car seat covers and related products have good export potential.
Cost EstimationPlant Capacity 100 Set/Day Land & Building (Area 450 sq.mt.) Rs. 37 LacsPlant & Machinery Rs. 12 Lacs W.C. for 1 Months Rs. 40 Lacs Total Capital Investment Rs. 90 Lacs Rate of Return 90% Break Even Point 33%
CAR SEAT COVERS AND RELATED PRODUCTS
Auto Body Pasrts of Plastic are made by Injection Moulding Process, Raw Materials used for this purpose are ABC,PP, Polycabonate,etc. in the form of granules which are passed through an Injection Moulding Machine and as the die design and shape the reequired Auto Part is fabricated. Pressure die casting in aluminium alloy offers means for very rapid production of engineering and other related component even or intricate design. The technique has obvious advantage when a component is required in large quantities. However for engineering components such as those required for aeronautic space defence and automot ive appl icat ion mechanical propperties and durability are of primary importance. It is therefore essential that the best features of design should be employed and optimum casting technique with minimum cost be adopted. Pressure die cast products are used in domestic as well as industrial field.
Cost EstimationPlant Capacity 1250 Kg./Day Land & Building (Area 450 sq.mt.) Rs. 39 LacsPlant & Machinery Rs. 41 Lacs W.C. for 1 Months Rs. 28 Lacs Total Capital Investment Rs. 1.15 Cr. Rate of Return 66% Break Even Point 34%
PLASTIC AUTO PARTS
Paper tubes should be of uniform weight, size and strength as it would make it possible to deternmine the weight of the thread often winding. The basic material used for paper tubes and composite cans is a board/paper. The body of usually is paper board and the ends usually are of metal, paperboard or plastics. The construction of the body may be one of three general type:- spiral wound tubes and cans, convolutely wound tubes and cans or laminated or lab seam cans. Spiral wound bodies are made on a spiral winder, which consists of a stationery cylindrical mandrel. An end less belt is looked over one end of the mandrel and a fraveling saw defines the other end the raw stock is slit into narrow rools which are fed into the winder from either side. Each web passes overs a glue roll, around the mandrel and under endless belt at 25-85.
Cost EstimationLand & Building (Area 1800 sq.mt.) Rs. 1.54 Cr.Plant & Machinery Rs. 57 Lacs W.C. for 3 Months Rs. 1.28 Cr. Total Capital Investment Rs. 3.60 Cr. Rate of Return 23% Break Even Point 47%
PAPER PACKAGING
The gloves are made from latex by dipping method. In the same plant of hand gloves, other products like finger stalls, baloons, etc. can also be manufactured. Deposition of rubber by dipping an article in rubber solution in order to obtain thin walled articles in and old process, toy baloons, gloves for surgical and household use were made by dipping forms in milled rubber solution as cements. A single dip was sufficient for producing very thin articles, but in case of heavy ones the dipping and drying operations had to be repeated several times. The solution uses as of high viscosity, yet it contain only a very small percentage of rubber, consequently the usage of solvent was high and the method of solvent recovery were very inefficient. It was not surprising that when latex become commercially available attempts were made to use it in place of rubber solutions. Dipped goods from latex especially surgical gloves, industrial gloves, finger stalls etc.
Cost EstimationPlant Capacity 1245 Million/Day Land & Building (Area 20000 sq.mt.)Rs. 8.90 Cr.Plant & Machinery Rs. 4.56 Cr. W.C. for 3 Months Rs. 9.17 Cr. Total Capital Investment Rs. 23.13 Cr. Rate of Return 46% Break Even Point 30%
LATEX GLOVES, CONDOMS & CATHETER
4449, Nai Sarak, Main Road, Delhi-110 006 (India)
Ph. : 91-11-23918117, 23916431Fax : 91-11-23916431, 23918117
E-Mail : [email protected], [email protected]
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 19 :-
Hand Book of DAIRY
FORMULATIONSProcesses &
Milk ProcessingIndustriesR
s.
75
0/-
Rs.
1100/-
Rs.
1100/-
AXIS Bank Ltd....... .....
....... .....C A-054010200006248
ICICI Bank Ltd. ...... ....
....... ....... ...C A-038705000994
Union Bank of India...
....... ....C A-307201010015149
State Bank of India....
....... ....... .....C A-30408535340
HDFC Bank....... ....... ..
....... ......C A-05532020001279
Yo
u c
an
de
po
sit
th
e a
mo
un
t in
E
IRI a
cc
ou
nts
eit
he
r in
Zari Colouring and coating is a important part to produce zari which is Acid resistance and Heat resistant. Surat Jari is one of the important product produced in Surat. This product is sold in both national and international market to cater the sari industries. There are a large number of peop le who a re engaged i n t he manufacturing of Surat Jari. The art of manufacturing Surat Jari Flourished during the Moghal period, and Jari articles from Surat were exported from the port to all parts of the world. When the East India Company landed in Surat in 1614, the town was a busy trading centre frequented also by Haj Pilgrims with their penchart for gilt-edged cloth. In subsequent years the French Jari started making its appearance in India. These imports, by the turn of the 19th century, all but killed the industry as Europes power driven machines made the french goods cheaper than what was produced here. The way the Jari makers tell it, the trade was saved by the first world war when French imports were banned. Following this the trade bounced back in all its splendour, a short-lived respite when the war ended, and imports resumed. The next shot in the arm, after 1920, came from an unlikely source, the British Govt. The view of few manufacturers regarding the Jari industries as follow.
Cost EstimationPlant Capacity 200 KGS/Day Land & Building (Area 300 sq.mt.) Rs. 15 LacsPlant & Machinery Rs. 2 Lacs W.C. for 1 Months Rs. 3 Lacs Total Capital Investment Rs. 21 Lacs Rate of Return 48% Break Even Point 54%
ZARI COLOURING
Re-refining of used oils is now accepted and recognised as a legitimate source of supplementing petroleum oils. Prior to the escalation of oil prices, petroleum lubricants and other industrial oils were very cheap and their conservation and saving was not economically attractive. Users did not care to recovery and preserve used oils, which were allowed to be lost or were disposed of by easiest possible means. Rise in Oil prices has compelled the users firstly to economise the use of oils and secondly to recover, grade and store the used oils. Attractive prices and ready acceptability have given a boost to this industry. The current production of re-refined oils in the country is around 30,000 tonnes per year. This is hardly five per cent of the oil consumed, therest 95 percent is lost. In most of the applications, lubricants only degrade and are not destroyed. Around 10 lakh tonnes/year of oils are therefore lost in the environment, and pollute ground and water. This therefore, requires and urgent look into the design of machines, and machine lubrication systems. The design criterion is required to be changed from used lubricant drain out to preservation and collection.
Cost EstimationPlant Capacity 1 MT./Day Land & Building (Area 2400 sq.mt.) Rs. 24 LacsPlant & Machinery Rs. 7 Lacs W.C. for 2 Months Rs. 23 Lacs Total Capital Investment Rs. 55 Lacs Rate of Return 45% Break Even Point 53%
RE-REFINING OF USED ENGINE OIL
All Laboratories in Schools,Collages, Universities, Research Institutions, Medical and Pathalogical Laboratories industrial Laboratories use these Glassware for various operations and experiments. The different types of Laboratory Glassware are tubes, beakers conical flask. measuring flask,pipette, burette etc. With the advancement in science and technology and the increasing trends in Schools & Colleges and also in the testing Laboratories (Medical & Industrial) leads to increase in the demand of laboratory glassware. Glass is one of man’s most valuable and versatile materials. About 700 different glass compositions are in commercial use. These are fabricated into tens of thousand of different articles that have combinations of properties for about a thousand essentially different uses. Laboratory Glassware manufacturing occupies an important role in the glassmanufacturingindustry.Theprocess of laboratoryglass ware manufactur ingcanbe d iv idedin to the continous production process and the batch process. Former is a process in which processes from the input of raw materials through the moulding of glass are conducted continuously and in equipose utilizing the tank furnace.
Cost EstimationPlant Capacity 15 Ton./Day Land & Building (Area 3000 sq.mt.) Rs. 1.38 Cr.Plant & Machinery Rs. 67 Lacs W.C. for 3 Months Rs. 1.37 Cr. Total Capital Investment Rs. 3.50 Cr. Rate of Return 32% Break Even Point 46%
LABORATORY GLASSWARE
Technology ofSynthetic Resins
&Emulsion Polymers
2011 Ed.
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 20 :-
Rs. 975/-
Street light fitting (Indoor & outdoor) is pricisely used by Govt Department i.e. Electricity Board, Development Authorities and rate contractors, etc. The fluorescent lamp is also a gaseous discharge lamp, the ‘gas’ being actually mercury vapour at low pressure. A large part of the light emitted by this discharge, however, falls in ultra-violet part of the spectrum and thus invisible; apart of this glass will not transmit ultra-violet rays to any extent. So that very little passes through the outside of the envelope. In order to arrive at a really efficient and economical source of light, the principle of fluorescence was introduced; by fluorescence is meant the phenomenon arising from the capacity of certain substances for absorbing short-wave radiations and re-emitting them as radiations of a longer wavelength. If for convenience we refer to the emissions just beyond the red and blue extremities of the spectrum by somewhat paradoxical term “invisible light.
Cost EstimationLand & Build (Area 1000 sq.mt.) Rs. 40 LacsPlant & Machinery Rs. 1.39 Cr. W.C. for 3 Months Rs. 3.14 Cr. Total Capital Investment Rs. 5.11 Cr. Rate of Return 58% Break Even Point 31%
LUMINARLIGHT FITTING (INDOOR & OUTDOOR)
There are two types of yeast as compressed yeast. It is convenient to use dry yeast powder for bakeries because its handling is simple and its preservation easy. Dry yeast which can be contained in the form of pillets or flakes in packets or tins. Can be kept for some time in cool, dry conditions. It is important to remember that: a. Approximately half as much dried yeast as fresh is required in any recipe. b. Reconstitution is necessary before using dried yeast. This is done by soaking the yeast is luke warm water at 85oF containing ½ oz, sugar to ½ pint water, the water and sugar used for reconstitution should be substracted from the quantities given in the receipt. Sugar can be omitted, but the proving is necessary with fresh yeast.
Cost EstimationPlant Capacity 5 MT./Day Land & Building (Area 2000 sq.mt.) Rs. 85 LacsPlant & Machinery Rs. 91 Lacs W.C. for 3 Months Rs. 1.25 Cr. Total Capital Investment Rs. 3.14 Cr. Rate of Return 45% Break Even Point 40%
YEAST FROM MOLASSES
Through out the commercial life time of a hydrocarbon fuel, from production at the weelhead to combustion in chamber, considerations of fuel storage movement, loss, safety and contamination apply. These are determined largely by the properties of the fuel itself and are therefore controlled by suitable property specifications. They are also influenced significantly by the design of the handling equipment, the procedures adopted and in some cases by the use of appropriate fuel additives. Bulk petroleum and hydrocarbons generally are most commonly stored in cylindrical tanks of welded steel construction up to about 100.000 Ton capacity mounted vertically on simple formulations of rubble and sand bituminmix.
Cost EstimationPlant Capacity 5555 Nos./Day Land & Building (Area 10000 sq.mt.)Rs. 79 LacsPlant & Machinery Rs. 1.37 Cr. W.C. for 3 Months Rs. 8.97 Cr. Total Capital Investment Rs. 15.94 Cr. Rate of Return 30% Break Even Point 35%
L.P.G. CYLINDER BOTTLING PLANT
Potable spring waters containing, sulphur iron, magnesium and other mineral salts occuring in certain regions are claimed to be beneficial to human matabolism. They occur in specific and widely scattered locations best known of which are white sulphur springs (Virginia) Hot springs (Arkansas), saragoge springs (New York) Vichy (France Baden (Germany) and (U.S.S.R.) The therapitic value of such waters is questionable carbonate mineral waters also contain lithium salts. Natural fresh water supplies are derived indirectly from the oceans; Clouds form by solar evaporation and the winds move the moisture overland to precipitate as rain, snow or hail. The water flows back to the oceans, completing the hydrological cycle. Water supplies are classified as surface supplies and underground waters. Surfaces waters are rivers, lakes, creeks, ponds, and reservoirs, wells & springs are the sources of underground water.
Cost EstimationPlant Capacity 30,000 Jars (20
ltr)/Annum 9,00,000 Bottles (1/2 ltr)/Annum 1,50,000 Bottles (1/2 ltrs)/Annum 6,00,000 Bottles (600 ml)/Annum 3,60,000 Glasses (250 ml)/Annum
Land & Building (Area 4 Kanals) Rs. 47 LacsPlant & Machinery Rs. 44 Lacs W.C. for 1 Months Rs. 6 Lacs Total Capital Investment Rs. 1 Cr. Rate of Return 69% Break Even Point 33%
MINERAL WATER WITH SODA WATER
The Kitchen equipments & gas tandoor are the roots of any Hotel and the quality of items produced in the equipments depends on proper fabrication and structural material etc. Catering industry, a specialized industry of paramount importance & bridges the gap between the main producer of steel and its consumers. This industry is essentially of a jobbing type and covers a vast range of widely different structural. Attempt may be made to find the broad limits of the industry in terms of the basis processes undertakes, which include cutting, welding and rivetting, primarily, and casting, forging and machining as subsidiary process. Steel fabrication find extensive use in various developmental activities though the range and extent of their utilization may vary from one sector to another. Traditionally the most important fabrications are the general use for all types of residential kitchens factories, offices, shops, schools, hospitals for conventional uses.
Cost EstimationPlant Capacity 5 Nos./Day Land & Building (Area 100 sq.mt.) Rs. 12 LacsPlant & Machinery Rs. 11 Lacs W.C. for 3 Months Rs. 15 Lacs Total Capital Investment Rs. 40 Lacs Rate of Return 50% Break Even Point 53%
KITCHEN EQUIPMENTS & GAS TANDOOR
Polymer’s today have become a part of every day life. They are processed so widely that their presence and availability is taken for granted. Infact it is hard to think of any field of endever where they are not used in one form or the other. They find wide application in almost all field and no exemption for electronics, medicine, packaging and building industries. Poly propylene has now joined polyethylene as one of the big new stars. The significant land mark of polypropylene is that it has penetrate into almost all field of application where H.D.P.E. can be and but if one can Judge by the rate new manufacturing capacity is being, a great many companies one belting on successful market penetration. On the other hand, facilities are usually also suitable for low pressure polyethylene manufacture, so risks may not be so great as they soon.
Cost EstimationPlant Capacity 8 Ton./Day Land & Building (Area 1000 sq.mt.) Rs. 25 LacsPlant & Machinery Rs. 1.09 Cr. W.C. for 3 Months Rs. 4.17 Cr. Total Capital Investment Rs. 5.64 Cr. Rate of Return 70% Break Even Point 25%
P. P. FILM
0 9 8 1 1 4 3 7 8 9 5
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 21 :-
Rs.
1050/-
Rs.
975/-
PVC Pipe fittings are integral and essential part of PVC piping systems. The are required where ever PVC pipes are used. The efficiency of various PVC piping systems depend largely upon the quality of the fittings used in pipe assembly. The most commonly used PVC pipe fittings are Sockets, Tees elbows, Bends, Joints etc. PVC pipes are fast replacing the conventional metallic pipes in many applications such as electrical conduits, irrigation, sanitary fittings, portable water etc. They are also used in tube wells and due to their chemical resistance properties they find applications in chemical plants too.
Cost EstimationPlant Capacity 4080 KGS/Day Land & Building (Area 2000 sq.mt.)Rs. 93 LacsPlant & Machinery Rs. 1.21 Cr. W.C. for 3 Months Rs. 1.56 Cr. Total Capital Investment Rs. 3.83 Cr. Rate of Return 45% Break Even Point 35%
RIGID PVC PIPES, HDPE PIPES & FITTINGS
Compressor Oils as the name implies are used for the lubrication of air, gas or refrigeration compressor. The compressor oil are usually naphthenic oil as these brake down to a fluffy soot. Paraffin oil though more stable are undesirable because they tend to form a hard deposit on decomposition which clogs the value. The compressor oils may be compounded as in many application relatively heavy contamination with water is almost certain. The oil used may have viscosity in the range of 150-550 SUS at 100oF. The demand and prospect of compressor oil is directly related to the growth of compressor in India.
Cost EstimationPlant Capacity 2 MT./Day Land & Building (Area 1000 sq.mt.) Rs. 51 LacsPlant & Machinery Rs. 15 Lacs W.C. for 1 Months Rs. 1.23 Cr. Total Capital Investment Rs. 1.92 Cr. Rate of Return 90% Break Even Point 18%
COMPRESSOR OILS
Sulphamic acid IUPAC recommendation amido sulphonic acid has the formula NH2 SO2H. It is a white crystalline solid non-volatile Non-hygroscopic D-2.1 m.p.205oC (decomposes) solubles in water slighty soluble in organic solvent odorless aqueous solution are highly ionized giving pH values lower than solution of formic phosphoric and oxalic acids. All the common salts (including calcium barium and lead) are extremaly soluble in water combustible.
Cost EstimationPlant Capacity 5 MT./Day Land & Building (Area 2000 sq.mt.) Rs. 95 LacsPlant & Machinery Rs. 33 Lacs W.C. for 1 Months Rs. 17 Lacs Total Capital Investment Rs. 1.50 Cr. Rate of Return 62% Break Even Point 32%
SULPHAMIC ACID (DESCALANT & TECHNICAL
GRADE, S.R.GRADE)
Electrophoretic lacquers are newwly innovated concept preusely used to protect precious metals like gold silver to protect from weather and moisture and empart shining. Electrophoretis involves the motion of electrically charged particles in an electric field lacquer (Electrophoretic) of suitable elielectric constant many be electrically polarized so that they attracted to a opposiotely charged surface. These lacquers are suitable for complex bodies and uneven surface. The demand of the product is bound to increase in the near future and there is good scope for new investment.
Cost EstimationPlant Capacity 250 KGS/Day Land & Building (Area 200 sq.mt.) Rs. 10 LacsPlant & Machinery Rs. 3 Lacs W.C. for 1 Months Rs. 8 Lacs Total Capital Investment Rs. 23 Lacs Rate of Return 87% Break Even Point 33%
LACQUER ELECTROPHORETIC FOR GOLD JEWELLERY POLYURETHANE BASED
When detergent is mentioned, the cake, bar or powder usually comes to mind. For small manufacturers, the best advice on making liquid detergents is to purchase from primary producers. Generally, there are two types of liquid detergents. 1. Light duty liquid detergent. 2. Heavy duty liquid detergent. Light duty detergents are in general use, although heavy duty liquid detergents are also being made but this has not captured the market to any serious extent. Liquids detergents, which actually proceeded powders, are used mainly for fine wash and dish washing. It can undoubtly be said that liquid detergents are an important part of today cleanser markets of developed countries. In India, liquid detergents is under development stage, except that is used in large quantities in textile mills for wet processing for textile goods.
Cost EstimationPlant Capacity 500 KGS/Day Land & Building (Area 400 sq.mt.) Rs. 20 LacsPlant & Machinery Rs. 6 Lacs W.C. for 3 Months Rs. 12 Lacs Total Capital Investment Rs. 39 Lacs Rate of Return 28% Break Even Point 54%
DISH WASHING LIQUID DETERGENT SLES BASED
Copper Lugs are the important item used in electrical industries as terminals cables and wires. In the past, the selection of terminals has been more a matter of individual preference, manufacturing technique, types of terminals in stock, and mechanical design, than it has been a question of electrical or electronic design. For years design engineers considered the selection of terminals and terminations to be not their problem but rather a function of the equipment manufacturer. With the stress that has recently been put on equipment reliability, however design engineers are giving more attention to the selection of terminals than they have in the past. Copper lugs are made in many basic designs and several variations of each design. These terminals also called lug. Wire terminals are divided into two major classes, the solder type and the pressure or crimp type. The solder type has a cup in which the wire is permanently held by solder.
Cost EstimationPlant Capacity 1 Ton/Day Land & Building (Area 600 sq.mt.) Rs. 31 LacsPlant & Machinery Rs. 9 Lacs W.C. for 3 Months Rs. 2.47 Cr. Total Capital Investment Rs. 2.90 Cr. Rate of Return 60% Break Even Point 22%
COPPER LUGS
MODERNTECHNOLOGY
OF ACID SLURRY
SURFACTANTS,SOAP AND
DETERGENTSWITH FORMULAE
Rs.850/-
Project Reports and Books on
PRINTING & PRINTING MATERIAL
is also available
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 22 :-
New 2011-12 Edition
Industrial park is intended to promote the stainless steel sector for hot and cold rolled product. Steel Cercles & Profiles, stainless Steel Utencil & Kitchenware, Hardware product, etc. and provide basis infrastructure facilities like power,water. Residential Block,Health care facility, office space Hospital and other basis aminities viz were house, shopping mall,etc for the benefit of the promoter. Stainless Steel is a high grade steel to which has been alloyed such elements as Manganesse (MN) silicon (Si) Phosphorus (P) chromium (Cr) Nickel (Ni) and Molybednum (Mo). Of these elements chromium and nickel are in the largest quantities. According to the particular type of steel, it will combain 10 to 30% of chromium and 10-25% of nickel.
Cost EstimationLand & Build. (Area 300 Acres) Rs. 5380 LacsPlant & Machinery Rs. 2185 Lacs W.C. for 3 Months Rs. 17 Lacs Total Capital Investment Rs. 28389 Lacs Rate of Return 39% Break Even Point 28%
INDUSTRIAL PARK FOR STAINLESS STEEL MANUFACTURING SECTOR
C.R.C. sheets are useful for manufacturing Auto parts trolly components electric components ets. Metallic parts are mass- produced in engineering. There are alot many similar simple sheet metal hardwares components parts used in automobiles electrical & housing constructions. For exapmle, the handle of the door is made in several pieces. A 3 to 5 mm thick sheet piece of disired contours, is inserted in a sufficiently strong & long rod. This rod with hanle slides in a formed space. But, the total axial movement of this bolting rod is limited by the space within which the handle strip can move (say 60 mm__ to 100 mm__). The enclosure, within which the handed bolt reciprocates, is made of steel sheet.
Cost EstimationPlant Capacity 144 Ton/Annum Land & Building (Area 450 sq.mt.) Rs. 32 LacsPlant & Machinery Rs. 17 Lacs W.C. for 1 Months Rs. 9 Lacs Total Capital Investment Rs. 62 Lacs Rate of Return 46% Break Even Point 47%
SHEET METAL PARTS/COMPONENTS
Construction Adhesives are the important part of construction application the bond of construction adhesives must retain the structural integrity through the life of the structure. Hence long term durability is an important requirement but limits choice of adhesive while many of these adhesives possess the necessary strength their working properties are often such that they cannot be used directly.
Cost EstimationPlant Capacity 500 KGS/Day Land & Building (Area 1200 sq.mt.) Rs. 61 LacsPlant & Machinery Rs. 9 Lacs W.C. for 3 Months Rs. 6 Lacs Total Capital Investment Rs. 82 Lacs Rate of Return 25% Break Even Point 56%
CONSTRUCTION ADHESIVE
Aluminium Exrusion dies are the important tools for aluminim industry and may be described as the heart of engineering industry. In fact for several extrusion products the know How lies in the design and making of extrusion dies and rapid industrilization has revolutionized the concept of aluminium extrusion. Aluminum extrusion is a necessity for production of extruded products viz pipes, rods, chanels profiles etc. for all diciplines of engineering industry and it has become imperative to produce various type of ALuminium extrusion die for aluminum extrusion plant.
Cost EstimationPlant Capacity 4 Nos./Day Land & Building (Area 600 sq.mt.) Rs. 25 LacsPlant & Machinery Rs. 65 Lacs W.C. for 1 Months Rs. 8 Lacs Total Capital Investment Rs. 1.05 Cr. Rate of Return 34% Break Even Point 49%
DIE MAKING FOR ALUMINIUM EXTRUSION
Nylon screen cloth with wooden frame is a important item used in screen printing and the versatile used screen printing has lent itself increasingly to advances in graphics and industrial technology screen printing play an important part in everyday living. It has played important role in the growth of plastic and electronic industries. The rapid growth of advertising has given a great a boost to the printing and production of display and increase in sales volume.
Cost EstimationPlant Capacity 2000 sq.mt./Day Land & Building (Area 1000 sq.mt.) Rs. 52 LacsPlant & Machinery Rs. 13 Lacs W.C. for 3 Months Rs. 90 Lacs Total Capital Investment Rs. 1.59 Cr. Rate of Return 41% Break Even Point 34%
NYLON SCREEN CLOTH WITH WOODEN FRAME
Ayurvedic Hair Oil for Colouring of Hair is gaining an immense prominence in modern times. The herbal/ayurvedic and medicated hair oils are used as medicine hair tonic. The herbal oil like banphool oil is exhibiting its versality owing to its embalming effect in alleviating headache and cause soothing effect. In allophatic field of medicines, those drugs used for analgesic purpose way have some side effects, but as the oil is basically made from herbs extracts which are naturally occurring, so it is free from any side effects or contra indications. The contents used in the preparation or this oil are extracts or lawanga,chandan (sandal wood oil),kewara, jatamansi. Colouring or tinting of hair is however in a great form from earliest antiquity. Henna was also used to obtain auburn tints.
Cost EstimationPlant Capacity 1000 KGS/Day Land & Building (Area 500 sq.mt.) Rs. 21 LacsPlant & Machinery Rs. 17 Lacs W.C. for 1 Months Rs. 83 Lacs Total Capital Investment Rs. 1.25 Cr. Rate of Return 53% Break Even Point 32%
AYURVEDIC HAIR OIL FOR COLOURING OF HAIR
Now-a-days engine oil has become an important factor for automobile and other purposes and since the prices of all petroleum products have gone up. It has become extremely necessary to refine used engine oil which could be reused as original. Keeping this view Defence Research (Materials), Kanpur has developed a very simple process which envisages utilization of sulphuric acid, activated clay and filter aid as the raw materials and the suggested reclaimed economical unit for this industry is 200 tons per annum, and estimated capital outlay is Rs.1.5 lacs. Engine oil becomes contaminated with foreign material in service. In circulating systems, where a substantial quantity of oil is involved, it is desirable to maintain it as clean as possible to provide maximum working efficiency and to keep wear and damage of lubricated parts to a minimum.
Cost EstimationPlant Capacity 5 KLS/Day Land & Building (Area 1000 sq.mt.) Rs. 15 LacsPlant & Machinery Rs. 21 Lacs W.C. for 1 Months Rs. 19 Lacs Total Capital Investment Rs. 60 Lacs Rate of Return 59% Break Even Point 53%
BLACK PETROLEUN PRODUCTS IN OIL FORM TO BE CONTERTED TO WHITE (THIN FILM DISTILLATION)
Rs. 650/-Technology of
SYNTHETIC & MAIZE AND
ALLIED CORNPRODUCTS
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 23 :-
AXIS Bank Ltd....... .....
....... .....C A-054010200006248
ICICI Bank Ltd. ...... ....
....... ....... ...C A-038705000994
Union Bank of India...
....... ....C A-307201010015149
State Bank of India....
....... ....... .....C A-30408535340
HDFC Bank....... ....... ..
....... ......C A-05532020001279
Yo
u c
an
de
po
sit
th
e a
mo
un
t in
E
IRI a
cc
ou
nts
eit
he
r in
www.eiriindia.org
The lubrication of the wire during passage through the die plays an important role, particularly with regard to lessening the amount of die wear. The subsequently applied lubricants for wire drawing may be dry soap (with a calcium stearate or sodium stearate base) or an oil with Extreame Pressure (E.P) additives. E.P. additives are chemicals which react with hot spots on the wire surface that result from lubricants breakdown. The resulting local surface compound has a low shear strength and functions as a provisional lubricant. Wire drawing lubrication is an extreemly complicated, often poorly understood subject. Whatever the chemical complexity of wire and rod drawing lubrication, some rather definite physical behaviour can be cited. At one extreme, the absence of lubrication, local or general, can lead to adhesion of the die. In such cases the surface of the wire is stripped off and a torn, rough, heavily striated finish results. The value of the friction is theoretically about 0.5, but value of about 0.25 are more relalistic averaged over the whole surface. When a minimal possibly monomolecular lubricant film exists, sticking no longer occurs and the wire assumers the contour of the die on a microscopic scale. This mode is called boundary, or thin film lubrication.
Cost EstimationPlant Capacity 600 KGS/Day Land & Building (Area 500 sq.mt.) Rs. 9 LacsPlant & Machinery Rs. 4 Lacs W.C. for 1 Months Rs. 8 Lacs Total Capital Investment Rs. 24 Lacs Rate of Return 45% Break Even Point 57%
WIRE DRAWING POWDER
Metallurgical knowledge had its beginnings in the stone age when same ancient craftsman first recognized the difference in behaviour amongst certain of the “rocks” with which he was working. The stones familiar to this primitive aetisan were hard and brittle, and were capable of being fashioned into tools and weapons only by fedious shaping, chip by chip. His first encoumter with metal then, undoubtedly native copper or gold, must have been an exciting experiences. Here was a susbstance which, instead of fructuring, yields to the blows of this stone hammer. Here was a material which could be formed much more precisely, which was pleasing to the eyes, which could be worked to a keener edge, and which more over some how acquired greater atrength the more it was worked.
Cost EstimationPlant Capacity 160 MT./Day Land & Building (Area 5 Acres) Rs. 400 LacsPlant & Machinery Rs. 290 Lacs W.C. for 1 Months Rs. 1307 Lacs Total Capital Investment Rs. 2067 Lacs Rate of Return 85% Break Even Point 29%
FERRO MANGANESE (LOW & HIGH CARBON)
As the name itself implies the readymade garments are garments ready for wearing. Wearing garment is a basic need for every human being. The trend for using ready made garments is increasing day by day. Ready to wear garments have been finding more and more acceptance in the indigenous as well as export markets mainly due to low cost of fabrication. Sewing, of cloth as well as saving of time. Manufacture of readymade garments is very simple and easily manageable. Machinery and Raw Materials required to start this industry are indegineously available. The scheme envisages for setting up a unit of ready made garments. viz. Cotton Shirts, Pyjamas, Petticoats and blouses which shall be quite acceptable in the rural markets.
Cost EstimationLand & Building (Area 2000 sq.ft.) RENTEDPlant & Machinery Rs. 1 Lac W.C. for 3 Months Rs. 22 Lacs Total Capital Investment Rs. 27 Lacs Rate of Return 36% Break Even Point 61%
FASHION GARMENTS RETAILING (BUDGET SHOP)
Rock Phosphate upgradation and process plant is a important plant due to its versatile uses in the process industries. The Rock phosphate is commonly known as phosphate pebbler is effectively extracted from adhered clay only after intensive wet attritioning screening and scrubbing with log washer at the plant. This product amount to about 15 wt % of mined matrix and contains about 30 wt % P2 O5 and 2.5 wt % iron and aluminium impurities. Rock phosphate is the primary source of super phosphate and is mainly consist of calcium phosphate. The main uses of Rock phosphate are in the manufacture of Phosphoric Acid Phosphate Fertilizer animal feed etc. The demand of the product is totally related to the growth and prospect of end user industries which is bound to increase in the near future. Hence there is a good scope for new investment and a new entrepreneur can well venture in this field. Rock Phosphate when very finely pulverized has limited use as a fertilizer itself chiefly because of the relatively below availability of the P2 O5. Its main consumption however is as a raw materials for the manufacture of phosphoric acid superphosphate,phosphorus and phosphorus compound. Florida has been the principal producing area for phosphate rock.
Cost EstimationPlant Capacity 100 MT./Day Land & Building (Area 10000 sq.mt.)Rs. 4.45 Cr.Plant & Machinery Rs. 1.45 Cr. W.C. for 3 Months Rs. 5.23 Cr. Total Capital Investment Rs. 11.32 Cr. Rate of Return 25% Break Even Point 44%
ROCK PHOSPHATE UPGRADATION & PROCESS PLANT
HI-Tech Projects, Sep'2011 www.eiriindia.org -: 24 :-
• Ayurvedic/Herbal Pharmacy • Blood Bags • Bandage Cloth Weaving On Power Loom • Crepe Bandage • Disposable Surgical Caps & Masks • Dextrose Saline (I.V. Fluid) In Plastic Bottle• Dextrose Saline (I.V. Fluid) • Disposable Needles for Syringes • Disposable Plastic Syringes • Diagnostic Centre • Electronics Blood Pressure Measuring
Instrument • Hospital Cum Nursing Home • Homeopathic Medicines • I. V. Fluids (FFS Technology) • I.V. Set- Cannula • Intravenous • Medical College • Plastic I.V. Bottles • Plaster Of Paris Bandages • Pharmaceuticals (Tablet, Capsule, Syrups And
Ointments)• Repacking Of Medicines • Surgical Cotton & Bandage • Surgical Examination Gloves • Surgical Bandage • Surgical Adhesive Tape On Cloth Surface • Surgical Methylated Spirit • Sodium Phosphate Enema • Veterinary Medicines
SURGICAL & DISPOSABLE MEDICAL PROJECTS
ALCOHOL, BEER, IMFL, COUNTRY LIQUOR, WINE & OTHER RELATED PROJECTS• Alcohol From Rice Straw • Alcohol From Molasses • Alcohol From Potatoes • Alcoholic Beverages And Vinegar From Coconut
Water • Alcoholic Drinks From Ethyl Alcohol By Mixing Of
Various Flavours (Flavoured Alcoholic Beverages)
• Beer Plant (E.O.U.) • Country Liquor • Cider Plant • Ethanol (Biofuel) • Grape Wine • Herbal Beer • Mineral Water (Packed In Bottles, Glasses, Jars) • Rectified Spirit For Potable Alcohol Industrial
Alcohol & Medical Alcohol • Rectified Spirit From Rice/Paddy Straw • Indian Made Foreign Liquor • IMFLl (Whisky) From Potatoes • Octanol (Octyl Alcohol) From Molasses • Potable Beer (Alcoholic) Based On Potato &
Barley/Malt • Vodka From Potatoes • Whisky • Wine From Dates • Wine From Mahua Flowers
MARKET SURVEY CUM DETAILED TECHNOECONOMIC FEASIBILITY REPORT
To get Loan/Finance from Banks/Financial Institutes. To set up your own industry/Unit To have detailed & Exhaustive Data on any Project
Eiri project reports are prepared by highly qualified & experienced consultants & Market Research and Analysis supported by a panel of experts and computerised.Data provided are reliable and uptodate collected by manufacturers/suppliers, plant already commissioned by India.
Each detailed projects report contain :
• INTRODUCTION : Project Mix, Uses and Applications, Quality Control Measure & their introduction for attaining required properties economy and Productivity Competence.
• MARKET SURVEY : Market position, Installed Capacity Production, Anticipated demand, Present Manufacturers, Statistics of Imports & Exports, Estimated Demand, Demand & Supply gap (if available). LI/IL Issued recently
• PROCESS OF MANUFACTURE : Inventory controls & Tests, Comparative study of process for Manufacturing the product formulations, Process flow Sheet Diagram, Process detail in stages from Raw Materials to Finished products.
• RAW MATERIALS : Raw Material specifications, Market Codes and Raw Material Prices, Sources of Procurement of Raw Materials (Imported/Indigenous).
• PLANT AND MACHINERY : Range of Machineries required, Detailed Specifications of Machines & Equipments, Prices of Machineries, Suppliers of Plant and Machineries.
• LAND & BUILDING : Total Land area requirement with rates, Covered Area break up with estimated costs of construction.
• PROJECT ECONOMICS : Land and Building, Plant, Machinery and Other Fixed Assets, Total Capital Investment, Working Assessment, Raw material & Consumable stores, Staff Salaries and Wages, Utilities and Overheads, Total Cost of Project, Sources of Finance/Refinance, Break Even Point Determination.
• ANNEXURES OF CHARTS /FINANCIAL ASPECTS : Repayment Schedule for 5 yrs. Result of Performance, Depreciation Chart for 5 Years, Cash Flow Statement for 5 years, Project Balance Sheet, Land Man Ratio etc.
For assessing Market Potential, Corporate Diversifications, Planning, InvestmentDicision Making and to start own setup, Entrepreneurs and Industrialists are
most welcome to contact EIRI at www.eiriindia.org
Eiri Technocratesand Engineers have just
prepared
"MARKETSURVEY CUM
DETAILEDTECHNO ECONOMIC
FEASIBILITY REPORTS"
on following lucrative projects which
are most viable and profitable and having bright
future scope Each report
Rs. 11700 to Rs. 25000/- only
www.eiribooksandprojectreports.com
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Agricultural Equipments• AAC & ACSR Aluminium Conductors (All
Aluminium Conductors)• Agricultural Equipments Including Threshers• Air Brake Helical Coil• Air Cooler• Air Filters (For Scooter Car & Excavators etc.)• Aluminium & Aluminium Alloys From Aluminium
Scrap To Make Utensils (Induction Furnace Melted)
• Aluminium Alloy Wheels• Aluminium Alloys From Aluminium Scrap To
Make Utensils (Induction Furnace )• Aluminium Hot & Cold Rolling Mill• Aluminium Conductors• Aluminium Bottle Manufacturing (Cold Extrusion
Of Aluminium)• Aluminium/Copper Cable Lugs• Aluminium Cans For Beer Packaging• Aluminium Cans For Capacitors• Aluminium Caps For Injection Vials• Aluminium Extrusion • Aluminium Furniture & Hardware• Aluminium Sheet Rolling Mill • Alloy Steel Casting (Foundry)• Aluminium Utensils• Aluminium Utensils & School Boxes • Aluminium Wire Drawing And Super Enamelling
For Winding• Anodised Aluminium Utensils• Anodizing Of Aluminium• Antimony Oxide From Lead Scrap• Anti Scale Compound For Adding In Sugar
Boilers• Arc Welding Filter Glass• Aluminium Foil Cutting & Roll Making• Auto Flaps For Trucks & Buses• Automobile Workshop (Garage & Service
Centre)• Auto Bulb• Auto Electrical Parts (Armature)• Auto Gears• Auto Horns• Auto Leaf Spring• Auto Tubes • Auto Piston Ring• Auto Piston• Auto Parts (Electrical And Electronic)• Auto Rubber Parts And Turned Components
Silent Block Bush And Ceiling Fan Shaft+• Auto Wire Outer (Outer For Auto Wire)• Bakery And Biscuits Equipments Fabrication• Ball Point Pen Refills• Ball Roller & Taper Bearing• Band Saw Blades• Barbed Wire• Barrels (Oil)/(Metallic Barrels)• Bath Fittings, Turned Components (All Type)
Sheet Metal (Job Work) And HDPE/PP Moulded Articles
• Battery For Car (Dry)• Battery Operated Three Wheelers• Benefication of Chromite Ore Processing
Charge Chrome• Bicycle Spokes• Bicycle Assembly• Brake Lining Asbestos/Resin Based & Asbestos
Free• Brass Artware/Hollow Ware Casting (With The
help Of Phenolic Resin)• Brass Casting • Brass Pipes From Brass Sheet With
Longitudinally Welding Brass Ware By Casting Method (Brass Articles Viz. Brass Pooja
• Lamps And Other Casted)• Bright Bars• Buffing And Polishing Industry (Job Work)• Butt Hinge (Brass Sheet)• Carbon Brush Holder & Slip Ring• Co2 Welding Wire Electrodes (Copper/Copper
Alloy Coated• M.S. Wire)• Carbon Film Resistors• Car Dealership (Hyundai)• Carburettors• Cast Steel Body Valve• Cast Steel Panes For Melting Furnace• Ceramic Coated Steel Pipes• Chemical Etching Of Stainless Steel• Chemical Resistant Iron & Steel• Concast Steel Bars• Cold Form Section Mill• Cold Rolled Forming Of Section And Other
Sections• C o ld Ro ll I n g Of M s S t r ip• Cold Twisted De-Formed Ribbed Steel• Cold Rolling Mill• Compressor (Hermetic) For Air Conditioners• Compressed Natural Gas (Cng Kit) For
Autovehicle• Continuously Cast Steel Wire Rods (5 Mm)• Continuous Casting Copper Wire Rods• Conveyor Beltings• Conveyor Belt, Transmission Belt & V Belts• Cooking Ranges• Copper/Brass Sheets, Circle & Utensils• Copper Foil• Copper Ingots, Rods Making & Wire Drawing• Copper Powder• Copper Products From Copper Scrap• Copper Smelting Plant• Copper Wire Rods From Copper Scrap• Corrugated Box Making Machinery And Other
Their Parts• Cylinder Liner For Automobiles• Disposable Plastic Razors• Door Locks/Pad Locks• Drill Bits & Tool Bits• Drum Closures• Erw Steel Pipes And Tubes• Erw Steel Conduit Pipe• Earth Moving Equipments• Engine Valves For Automobiles• Fabrication Of Heat Exchanger• Fabrication Of Storage Tanks And M.S. Drum• Ferrous Alloy Ni-Hardy I.V Casting• Ferrous Mn Alloy Casting By Alumina Thermic
Process• Ferro Alloys• Ferro Silicon & Ferro Manganese From Dolomite
(Sms Grade)• Fire Extinguishers• Fire Fighting Equipments And Appliances• Flip-Tone Cans• Forged Conecting Rod• Forging Unit• Fountain Pen Nibs• Foundry Sand
• Free Wheels, Free Wheel Bushes And Free Wheel Plates For Autorickshaws
• Fuel Briquettes From Agro Waste• Fuel Injection System• Fused Magnesia• Generator Canopy• Galvanized M.S.Strips• Galvanizing Plant• Galvanized Iron Wire (G.I. Wire)• G.I. Pipes• Gas Welding Torches And Nozzles• Gasket Sheet • Gate Grills & Window Frames• Generating Set (Diesel)• Hard Anodised Aluminium• High Pressure Cylinder• Hollow Concrete Spun Pole• Hospital Wares• Hospital Furnitures• Hot Rolling Of Stainless Steel Sheet• Hot Dip Galvanizing • Hot Forged Fasteners• Hot Mix Plant • Industrial, Petroleum And Nuclear Filter• Ignition Coil For Automobiles• Injection Moulded Plastic Compounds With Tool
Room• Injection Moulded Plastic Components And
Metal Pipe Spinning Unit• Investment Casting • Iron Ore Pelletization Plant• Iron Ore Mining And Manufacture Of Sponge
Iron• Iron/Steel Wire Gauge• Iron Tawa• Knives (S.S.Knives)• Kitchen Sink (S.S.)• Lead Tube• Lead Alloy From Battery Scrap• L.P.G Regulators• Lpg Cylinder• Lpg Stove• Lpg Bottling Plant (Gas Filling)• M.S. Pipe (Mild Steel Pipe) - Welded• Machine Screws & Self Tapping Screws• Machinery For Cold Rolling Mill• Maruti Workshop Cum Service Station• Magnesium Ingots & Bullets Casting• Manufacture Of Tin Containers• Manufacture Of Storage Tanks, Pressure
Vessels, Heat Exchangers• Mark Ii Hand Pumps• Maruti Workshop Cum - Service Station• Mechanical Jacks• Medical Oxygen Gas Cylinder• Metal Cable Trays• Metal Cutting Die Design• M e t a l C u t t i n g O f A n d G r i n d i n g
Wheels(Abbrasive Cutting Wheels)• Metal Foundry Flux For Aluminium• Metal Foundry Flux For Cast Iron Casting• Metal Hooks & Clips • Metal Separation (Copp- Er , Tin, Lead) From
Spent Wash Acid• Metallic Ring Joints• Metallic Gasket (Spiral Wound)• Microvee & Absolute Filter• Microwave Oven• Mild Steel Ingots• Mini Steel Plant/M.S. Ingot By Induction Furnace• Mini Steel Plant• Modern Vehicle Workshop• Moped• Mild Steel Nuts• M.S.Hinges• M.S.Ingot And Hr. Steel Structurals• M.S.Ingot By Induction Furnaces• M.S. Pipes
AUTOMOBILES, MECHANICAL,
STEEL & IRON & METALLURGICAL
www.eiribooksandprojectreports.com
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
CHEMICAL (ORGANIC & INORGANIC)
WITH PETROLEUMPRODUCTS
• M.S. Tubes And Pipes• M.S. Welding Electrode• Mufflers & Silencers For Three Wheelers• Nail Cutter With Filer & Manicure• Nichrome Wire• Nickel Lined Screens• Non-Ferrous Alloy Rolling• Non-Ferrous Forging • Non-Ferrous Foundry• Non Pressure• Incandescent Lamp• Number Combination Locks For Luggages• Nuts & Bolts• Oxygen Lancing Pipes• Paper Coated Aluminium And Copper Wire• Perforated Metal Sheets• Petromax Container Photo Etching Of Stainless
Steel Plates• Pipe Galvanizing Plant • Piston Ring-Automobile• Plant Protection Equipments• Platinum Laboratory Apparatus• Pressure Cooker & Aluminium Utensils • Pressure Cooke(Aluminium)• Pressure Die Casting• Printed Aluminium Collapsible Tubes• Printed Tin Containers• Printing Press (Cylinder Machine)• Pumps For Chemical Industry (Special)• Railway Sleepers (M.S.)• Razor Twin Blade• R.C.C Spun Pipes• Reconditioning Of M.S. Drums/Barrels• Re-Rolling Copper And Brass Sheet And Rods• Re-Rolling Mills• Resin Coated Sand• Resin Cored Soft Solder Wires• Rolling Mill• Rolling Mill (By Induction Furnace) &
Manufacture Of Bars, Angles, Squares, Tubes And Others
• Roller Bearing & Forging • Rolling Of Stainless Steel Patta• Rollinf Mill By Tmt Technology• Rubber Insulated Pliers (Hand Tools)• Rubbing Compound For Automobiles• Scientific Laboratory Equipments• Scooter Assembling• Secondary Lead Extrac -Tion By Scrap Battery
Plates, Pipes & Sheet • Seamless M.S. Tubes & Pipes • Self Tapping Steel Screw• Sewing Needles• S.G. Iron & Alloy Steel• Sheet Metal Products, (Ferrous/Non-Ferrous)• Steel Drums And Barrels• Ship/Marine Container• Shock Absorbers• Shoe Eyelets• Shot And Grits By Automization Process• Shovels• Silico Manganese Alloys• Silencers (Mufflers) Exhaust & Tail Pipe For All
Types Of Vehicles• Sintered Bearing• Sintered Bushes• Sintered Metal Products• Soft And Hard Ferrites• Spanners• Spark Plugs• Spin On Filters And Spin On Filters Components
(Including Bowls)• Sponge Iron From Iron Ore• Steel Plant (Electric Arc Furnace Based- Eaf)• Spheriodal Graphite Cast Iron• Spray Dryer• Stainless Steel Casting By Induction Furnace• Stainless Steel Hinges
• Stainless Steel Fasteners (Nut And Bolts)• Stainless Steel Sheet Rolling• Stainless Steel Pipes• Stainless Steel Patta• Stainless Steel Sheet Rolling To Produce
Stainless Steel Utensils • Stainless Steel Utensils• Stainless Steel Wire Drawing• Staple Pins,Paper Pin , Gem Clips Etc.• Steering Wheel And Connecting Rod• Steel Castings• Steel Chain• Steel Foundry• Steel Furnitures And Electrical Appliances• Steel Furniture And Room Cooler• Steel Nipple For Bicycles• Steel Plant (Mini)• Steel Re Rolling Mill • Steel Rods And Coils From Scraps• Steel Rolling Mill (Reinforcement Bars)• Steel Rolling Mill• Steel Strips (Cold Rolled) Silicon With Grain
Riented For Electric Use• Steel Tubular Poles• Steel Transmission Line Towers & Rolling Mill To
Produce Steel Section• Steel Furnitures And Electrical Appliances• Steel Furniture And Fire Fighting Equipments• Steel Furniture And Room Cooler• Steel Wire Drawing And Galvanizing• Steel Wire/Rod• Steel Wool• Ston Scrusher And Screening Plant• Submerged Arc Welded Pipes• Submersible Pump Manufacturing• Super Enamelled Copper Wire• Super Enamelled Copper Wire (From Copper
Cathode Rod)• Three Wheelers• Tie-Rod Ends• Tin Containers• Toolroom And Sheet Metal Products• Trolley (Shopping) For Carrying Of Stores At
Super Market And Ware Houses• Tractor Trailers• Transmission Power Fitting• Tubular Poles• Tyre Retreading By Cold Process• Super Enamelled Copper Wires• Trolley (Shopping) For Carrying Of Stores At
Super Market & Ware Houses• Tmt Bars• Tubular Poles For Electrical Transmission (By
Fabrication Process)• Tubular Poles Of M.S. & High Tensile Steel• V- Belt• Vacuum Cleaners• Vacuum Flask (Stainless Steel)• Valves For Refrigeration And Air-Condition• Vehicle Welding & Painting• Venetion Blind• Washing Machines (Automatic & Computerised)• Water Controller (Automatic)• Watch Straps/Chains/ Bracelets/Belt Brass &
Stainless Steel• Water Coolers• Welded Wire Mesh • Welding Electrodes• Wheel Barrow• Wick Stoves• Wind Mill Window Frame (Ferrous & Non-
Ferrous)• Wrist Watch
• Acetic Anhydride• Acetic Acid (Glacial)• Acetic Acid From Ethanol• Acetone• Acetylene Black• Acetyl Chloride• Acetylene Gas• Acetylene Gas & Oxygen Gas (Integrated Unit)• Acid Black Dye• Acid Slurry • Activated Alumina• Activated Bleaching Earth (Activated Fullers
Earth) • Activated Carbon From Cashewnut Shell• Activated Carbon From Rice Husk• Activated Carbon From Rice Husk, Coconut
Shell & Coconut Powder• Activated Carbon From Wood • Activated Carbon Powder & Granules From
Coconut Shell• Activated Carbon & Sodium Silicate From Paddy
& Rice Husk• Alcohol From Broken Rice• Alum For Water Treatment• Adhesive (Fevicol Type)• Aerosol Insecticides Spray (Baygon, Hit,
Mortein Type)• Agarbatti Synthetic Perfumery Compounds• Alcohol From Potato• Alcohol From Rice Grains• Alcohol From Rice Husk• Alcohol From Molasses• Alcohol, Beer, Starch, Liquid Glucose, Dextrose,
Sorbitol, Vitamin-C,• Alcoholic Beverages And Vinegar From Coconut
Water• Germ Oil, Cattle Feed Etc. From Maize• Alkyd Resin• Alkylated Phenol Likenonyl Phenol, Dodecyl
Phenol• Alum (Non Ferric) • Alum (Ferric)• Aluminium Chloride From Aluminium Ore• Alum Cake• Alum From Aluminium Hydrate• Aluminium Ingot By Bauxite • Aluminium Phosphide• Aluminium Phosphate• Aluminium Sulphate (Non Ferric Alum) 17% -
18% Alumina Content In Granules (2 Mm To 4 Mm) And Flakes
• Amines & Allied Products• Amino Acid• Ammonia Gas• Ammonia Gas Bottling• Ammonia Liquor• Ammonium Nitrate• Ammonium Chloride (Pure & Technical)• Ammonium Sulphate• Annato Seed Extraction And Processing• Anti Corrosion Chemicals
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Anthranilic Acid From Phthalic Anhydride• Anesthesia (All Types) Used In Hospitals• Aniline• Argon Gas• Ariel Type Detergent Powder • Anthraquinone• Antimony Trioxide• Atenolol• Auramine “O”• Azodicarbonamide• Baking Soda From Ash• Barium Carbonate• Barium Compounds• Barium Nitrate• Barium Peroxide• Barium-Thio-Sulphate Banzene• Baryte Powder• Bar Soap (All Varieties) Using Soap Noodles• Beer Plant• Belt Paste • Beneficiation Of Chromite Ore Processing
Charge Chrome• Benzyl Acetate, Benzyl Benzoate, Benzyl
Alcohol• Beta Naphthol• Bentonite Powder• Benzoic Acid• Benzidine• Biofertiliser From Mother Culture• Bio Oil For Power Generation From Coffee Husk• Bio Gas Plant• Bio Gas Filling In Cylinder• Bio Tech Unit• Bi-Chromate Of Sodium, Potassium &
Ammonium• Bi-Functional Black Mfgr.Reactive Dye (Dye
From Cotton Yarn Dyeing)• Bio-Fuel (Jatropha Cultivation And Extraction)• Bituminous Roademulsion • Black Phenyl• Black Sulphur• Bleaching Powder (Stable)• Blue Detergent Powder• Bone Crushing Plant• Bone Meal (Calcined) Enrichment With Calcium
& Phosphorus• Boric Acid• B.O.N. Acid• Bromine Gas Plant• Brandy• Butanol• Butyl Rubber For The Manufacture Of Tubes For
Truck And Car Tyres• 1,4, Butanediol• Butyl Acetate• Caffein From Tea Waste• Calcined Lime (Dead Burnt Dolomite)• Calcined Petroleum Coke• Calcining Of Magnesite & Dead Burnt Magnesite• Calcium Aluminate• Calcium Based Grease• Calcium Carbide• Calcium Carbonate • Calcium Carbonate (Precipitated) From By
Product (Lime Slurry & Carbon Dioxide)• Calcium Carbonate (Activated & Precipitated)• Calcium Chloride• Calcium Gluconate• Calcium Nitrate• Calcium Silicate Bricks• Calcium Stearate By Fusion Process• Camphor Powder (Synthetic)• Construction Chemicals (With Detailed Market
Survey And Formulae Etc.)• Carbon Dioxide• Carbon Black From Fertilizer Waste• Carbon Black (Petroleum Based)
• Carboxy Methyl Cellulose (Cmc)• Casein And By Products• Casein From Milk• Cationic Softner (Stearic Acid Based)• Caustic Soda• Caustic Soda From Soda Ash By Soda Lime
Process• Caustic Soda (Liquid) By Electrolytic Process• Caustic Soda From Trona• Caustic Soda, Chlorine And Hydrogen Gas By
Electro-Lysis Of Brine Solution• Cellulose Acetate Moulding Powder• Cellulose Powder & Micro Crystalline Cellulose
Powder • Cement Admixture• Cement Colour• Cement Water Proofing Compound• Cement From Fly Ash & Lime• Cement Tiles (Glazed) • Chlorinated Paraffin Wax (Cpw)• Citric Acid From Lemon• Citric Acid From Molasses• Double Firing (Heating)• Chelated Zinc (Zn Edta)• Chemicals From Prawn Head• Chitin & Chitosan From Prawn Shell Waste• Chloral Hydrate• Chloramphenicol• Chromic Acid (With Pollution Control)• Chromic Acid (Oxide) & Blue Oxide• Chlorinated Paraffin Wax (Cpw)• Chromic Acid• Cement Paint & Distemper • Citric Acid From Lemon• Citric Acid From Molasses• Cleaning Of Cooling System And Boiler• Coal Tar Distillation• Coal Washing Plant• Cobalt Octoate• Compost For Mushroom• Construction Chemicals Copper Oxychloride• Coolant (Engine)• Copper Phthalocyanine Blue & Green• Correction Fluid• Cupric Chloride• Crude Oil Bleaching For Petroleum Jelly• Cutting Oil• Cyanuric Chloride• Cyanoacrylate Adhesive• Cutting Oil• Defoaming Agent For Paper Industry• De-Nickeling (Electrolytic Process)• Detergent Cake & Powder• Detergent Powder• Detergent Concentrate (Idet 10)• Dextrose Monohydrate & Dextrose Anhydrous
Powder From Tapioca Starch• Di-Basic Lead Stearate• Di Calcium Phosphate• Diclofenal Sodium Slow Release (Sr) Tables
100mg.• Di Ethyl Oxalate• Di Methyl Orthophthalate• Di-Methyl Phthalate• Diclofenac Gel• Dioctyl Phthalate (Dop)• Di Phenyl Glycerine• Di Phenyl Oxide• Dinitro-Chloro Benzene• Distillery • Distilled Water• Dodecyl Benzene Sulphonate• Dustless Chalk• Edta & Its Salts• Electroless Nickel Plating On Plastics• Electrolyte (Like Sulphuric Acid) For Lead Acid
Dry Rechargable 5.5.Ah. Battery• Electropolishing On Gold Jewellery• Electropolishing On Various Metals• Endosulfan• Enzyme Based Detergent Powder• Ephedrine Hydrochloride• Epoxy Resin Based Compound • Ethanol (Biofuel)• Ethyl Alcohol From Molasses• Ethyl Acetate• Ehtyl Ether• Ethyl Alcohol (Potable Liquor)• Ethyl Hexanol• Extra Temperature Lubricating Grease• Extraction Of Essential Oils By Sugar Critical Fluid
(Carbon Dioxide) Method From Flowers, Herbal & Spices
• Fabric Stain Remover• Fatty Acid• Ferric Alum• Ferric And Non Ferric Alum (Aluminium Sulphate)• Ferro Chrome Ligno Sulphonate• Ferro Manganese• Ferro Silicone• Ferro Vanadium From Vanadium Sludge• Ferrous Silicate• Ferrous Sulphate• Ferrous Sulphide• Fertilizer From Animal Blood & Leather Waste• Fluorescent Tube Light Powder• Foamed Pvc Compounding & Its Products • Formaldehyde• Food Grade Grease Or Lubricant• Fractional Distillation Of D.M.O (Dementholized
Oil)• Fractional Distillation Of Essential Oil &
Medicinalplant Extract• Friction Dust (Liquid & Powder) From Cnsl• Fruit Flavours• Furfural From Rice Husk• Fumaric Acid• Gas Filling Of Lpg Cylinder • Garlic Acid• Ginger And Garlic Paste• Ginger Processing• Gasket Shellac Compound• Gear Oil• Gibberellic Acid• Glass Putty• Gluconic Acid• Glucose D- Powder• Glycerine • Gossypol (Poly Phenol) From Cotton Seed Oil• Greases (Lithium Based)• Guar Gum Powder• Hair Fixer (Hair Gel Type)• High Temerature Grease• Hard Grease• H - Acid• Henna Paste Making• Henna Powder Repackaging• Heptal Dehyde• Herbal Beer• High Carbon Ferro Chrome• Humid Acid• Hydrated Calcium Silicate Brick• Hydrated Lime From Sea Shell• Hydrochloric Acid• Hydro Fluoric Acid• Hydrogen Peroxide (By Auto-Oxidation Process)• Ice Packs (Solutions Type, White Gel Type, Violet
Semi Solid Polymer Type)• Improving Drop Point Paraffin Wax From 45-500c
To 75-800c• Industrial Alcohol• Integerated Complex Of Easter & Allied Products
(D.O.P, D.B.P, Ethyl Acetate Wire Enamel & Cable Jelly)
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Insta Whitening System (Ujala Type)• Imfl (Whisky) & Country Liquor• Imfl (Whiskey) From Potato• Iron Oxide For Making Feritte• Iron Sulphide• Jatropha (Biodiesel) Cultivation And Extraction• J. Acid• Jute Batching Oil• Kesh Kala Tel (Hair Dye Lotion) (Vasmol 33,
Black Nite Type)• L-Lysine Monohydrochloride• Lactic Acid From White Sugar By Fermentation
Process• Ldpe Granules From Virgin (Ldpe Resin) • Lead Extraction From Battery Scrap• Lead Oxide (A) Lead Monoxide • (B) Lead Tetra Oxide • (C) Greylead Oxide• Liquid Glucose & Its By Products• Liquid Gold (In Paste Form)• Lemon Oil From Lemon• Liquid Oxygen Bottling Plant• Liquid Shoe Polish• Liquid Floor Polish• Lithium Based Grease• Linear Alkyl Benzene Sulphonate• Lube Oil Viscosity Improved For P.P.G/P.E.G.• Lube Oil And Greases• Lube Oil From Cnsl To Reduce Friction• Lubricants Ashless 100% Combustion• Maize Oil• Magnesium Carbonate And Magnesium
Bicarmonate• Magnesium Hydroxide Powder• Magnesium Silicate• Magnesium Sulphate• Malachite Green• Maleic Acid• Maleic Anhydride• Manganese Sulphate• Manufacturing Of Carbon Mono-Oxide Water
Gas• Menthol Bold Crystals From Flakes• Menthol Crystal & Mentha Oil• Mercuric Oxide• Metal Pre-Treatment Chemicals • Methyl Chloride• Methyl Cinnamate• Methane Gas By Sodium Acetate & Soda Lime • Methyl Acetyl Ricinolate• Methyl Parathion 2% Dust Powder• Methyl Stearate• Metol• Metol From Hydroqui-None & Methylamine• Micanite• Micro Crystalline Wax• Micro Nutrient Mixture• Mineral Water• Mineral Water And Pet Bottilng Plant• Mineral Water In Bottles, Glass And
Pouches• Mini Cement Plant (By Rotary Kiln Process)• Mixed Fertilizer• Mosquito Repellent Vaporiser (Liquid Mosquito
Destroyer)• Mosquito & Flies Repellent Agarbatti (Incense
Sticks)• Monochloro Acetic Acid• Monocrotophos (Technical)• Mosquito Coil • Mosquito Coil & Mat• Mosquito Mat• Mosquito Net• Mosquito Coil Agarbatti• Mother Tincture & Bio Chemic Medicines• Naphthalene & Phenyl (Integrated Unit) • Natural Mineral Water By Reverse Osmosis
Process• Nickel Plating Brightner (Primary Or Carrier
Brightner & Secondary Brightner)• Nickel Sulphate• Nicotine From Tobacco Waste• Nicotine Sulphate From Tobacco Waste• Nitro Benzene• Nitro Cellulose Sanding Sealer/Lacquer• Nitro Musk• Nitrogen & Oxygen Gas Plant• Non-Ionic Surfactant (Wetting Agent)• No-Carb Paste• Npk Mixed Fertilizer (Molasses Based)• N.P.K Fertilizer• Octanol• Oleoresin From Chilly And Ginger (Extraction)• Oleoresins From Marigold Petals (Extraction)• Organic Fertiliser• Ortho Nitro Phenol• Ortho Phthalic Polyester• Oxalic Acid From Molasses• Oxalic Acid From Rice Husk• Oxalic Acid From Tree Bark• Oxalic Acid From Waste Vegetables• Oxygen Gas Plant• Oxygen And Nitrogen Gas Plant• Oxygen Gas Plant (Air Seperation Method)• Para-Amino Benzoic Acid• Para-Amino Phenol• Para Toluene Sulphonic Acid• Pectin From Raw Papaya• Pectin From Apple Pomace• Pectin From Mango Peel• Pectin From Oranges• Pectin From Citrus/Lemon• Perfume (Lemon & Others) • Perfume Spray Deodorant (Non-Alcoholic)• Pest Control• Pesticide Preparation Using Neem Fruit &
Seeds (Margosa)• Pet Bottles From Pre-Form• Pet Granules (Dana)• Pet Preform From Resin For Pet Bottles• Petroleum Jelly• Phenol• Phenyl Acetic Acid• Phenyl• Phenyl (Black) In Liquid Form• Phthalic Anhydride• Phosphoric Acid From Rock Phosphate• Phosphorus By Chemical Process• Photo Emulsion For Rotary Screen Printing• Phthalocyanine Blue• Pigment Emulsion For Textile• Pigment Gum• Plant Growth Reagen Based Chlorothyltrimethyl
Ammonium Chloride• Plant Harmones Based On 2,4-Dichlorphenoxy
• Acentic Acid & Naphthalene• Plastazote Polythylene Foam Used For Fibre
Cable Joint• Plasticine (Modelling Clay)• Plastic Waste Reprocessing• Plaster Of Paris Bandages• Polyester Resin (G.P. Grade Laminate Grade,
Electrical Grade)• Polyol From Propylene Oxide• Poly Vinyl Acetate• Polyvinyl Acetate Emulsion• Polyvinyl Alcohol• Polyurethene Foam • Potassium Dichromate/Bichromate• Potassium Iodate• Potassium Nitrate• Potassium Permagnate• Potassium Per Sulphate
• Potassium Sulphate (Fertilizer Grade)• Potassium Per Oxy Di-Sulphide• Potassium Silicate By Ion Exchange Process• Potassium Silicate• Potassium Stearate• Processing Of Datura Stramonium Into
Hyosyamina And Atropin• Power Alcohol• Pvc Resin From Ethyl Alcohol• Pyridine & Its Derivatives• Rapid Fast Dyes (Only Process) • Reactor (Chemical)• Resorcinol• Reclamation Of Used Engine Oil (By Clay &
Vacuum Distillation Process)• Refinery Petrol/Diesel Etc.• Reclamation Of Spent Bleaching Earth• Reclamation Of Nickel Spent Catalyst From
Vanaspati Industry• Rectified Spirit From Molasses & Mahua Flowers• Rectified Spirit From Rice Straw• Red Oxide Paint/Primer (Anti Corrosive) Based
Organic Red Pigments• Refinery Petrol/Diesel Etc.• Removal Of Antimony From Lead Scrap• Resorcinol• Rice Bran Oil (Rbo)• Rosin Sizing Agent• Resorcinol• Rust Prevention Lube Oil• Saline And Injection Water• Salicylic Acid• Santonin• Sennosides From Senno Leaf• Silicone Grease• Shoe Polish • Silica Gel (Blue Self Indicating Process)• Silica Ramming Mass• Silicone Emulsion• Silicone From Rice Husk• Silicon From Silica (Semi Conductor Grade)• Silicon Grease• Silicone Oil• Silicone Resins• Silicone Spray • Silver Brazing Foil• Silver Extraction From Waste Hypo Solution• Silver Nitrate • Silver Parts For Ceramic Capacitor Single Super • Phosphate & Mixed Fertilizer (Npk)• Single Super Phosphate (S.S.P) & Sulphuric Acid• Soda Ash• Soda Ash From Natron• Soda Water Bottling Plant (Carbonated
Beverage)• Sodium Aluminate• Odium Benzoate• Sodium Bi-Carbonate (Baking Soda) From Soda
Ash• Sodium Chlorite• Sodium Chromate• Sodium Cyclamate• Sodium Di-Chromate• Sodium Di-Chromate & Sodium Sulphate As Bye
Products• Sodium Hexa Meta Phosphate• Sodium Hydrosulfite • Sodium Hypo Chloride (Bleach Liquor)• Sodium Iso-Propyl Xanthate• Sodium Lauryl Sulphate• Sodium Lauryl Sulphate & Sodium Lauryl Ether
Sulphate• Sodium Nitrate • Sodium Petroleum Sulphonate (Emulsifier)• Sodium Silicate From Silica & Soda Ash• Sodium Silicate From (1) Paddy Silk Husk 2) &
Silica
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Sodium Silicate By Hydro Thermic Process Using Quartz And Caustic Lye
• Sodium Carbonate & Silica • Sodium Sulphate • Sodium Sulphide By Barium Sulphate Process• Sodium Sulphide From Ammonia & Sodium
Chloride• Sodium Sulphite• Sodium Tri-Poly Phosphate• Soluble Cutting Oil• Softener (Cationic Anionic & Non-Ionic)• Spirit From Pine Apple• Stannous Chloride• Stearic Acid• Stearates Manufacture (Calcium, Zinc,
Aluminium, Magnesium Stearates)• Sulfanilic Acid In Powder Form• Sulphur From Pyrites & Slag• Sulphur Crystals/Lumps• Sulphuric Acid• Sulphuric Acid From Dcda Process• Super Phosphate (S.S.P)• Synthetic Iron Oxide (Yellow)• Synthetic Red & Wellow Iron Oxide From Iron
Filling & Pickle Liquor• Synthetic Zeolite• Tannic Acid• Tartaric Acid• Teflon Grease• Textile Marker Pen/Tube• Toilet Cleaner• Toluene And Sbp From Crude Naphtha• Trimethyl Ammonium Chloride• Triphenyl Phosphite (T.P.P)• Ultramarine Blue (Liquid)• Urea Formaldehyde & Melamine Formaldehyde
Powder• Undecylinic Acid• Vinyl Acetate Monomer• Vitamin C• Vitamin E• Waste Water Treatment Plant For Industrial
Sector In India (Only Marker Survey)• Washing Soap And Powder• Wall Putty• Water Proofing Chemicals• Water Treatment Plant• Weedicide• Wire Drawing Lubricants• Wire Enamels• Wood Polish (Non Alcoholic)• Xanthates• Yellow Dextrin• Zinc Chloride• Zinc Oxide• Zinc Phosphating By Cold Process• Zinc Silicate• Zinc Stearate• Zinc And Copper Sulphate From Brass Ash• Zinc Sulphate• Zinc Sulphate Monohydrate• Acid Black • Auramine’o’• Azo Dyes Stuff• Dye & Dye Intermediate• Dye Intermediates• Malachite Green• Methylene Blue• Phthalocyanine Blue• Phthalocyanine Blue & Green• Reactive Dyes• Sulphur Black Dye • Vat Dyes• Water Chilling Plant• Water Treatment Chemicals• Water Treatment Plant• Wadding Oil (100%) For Wadding Of Cotton • Hosiery Cloth In The Dyeing Process• White Oil• Wax Floor Polish
ELECTRICAL, ELECTRONICS, COMPUTERS & INFOTECH / IT
PROJECTS• Air Conditioning • Aluminium Alloy Conductor• Aac And Acsr Aluminium Conductors• Aluminium Cable• Aluminium Electroytic Capacitors• Audio Cassette Assembling & Recording• Audio Cassettes Duplicating Recording• Audio Cassettes & Audio Studio• Audio Cassettes Plane & Recorded• Audio Magnetic Heads• Audio Magnetic Tape• Audio/Video Cassettes• Auto Bulb/Lamps• Automatic Voltage Stabilizer• Battery Plates• Business Process Outsourcing (Bpo)• B/W Tv & Computer Monitor Picture Tube• Bread Boards• Call Centre• Call Centre – International• Camera (35 Mm)• Capacitors• Carbon Electrode Used For Battery Cell• Carbon Potetiometers• Ceiling Fan• Ceiling Fan (Stainless Steel)• Ceramic Insulator• Children Infotech Training Institute (Rs. 10000/-)• Choke And Patti• Choke And Starter• Choke Used For Fluorescent Lamps• Colour Television• Colour And Black & White Television• Compact Disc• Compact Disc Player (Audio/Video)• Computer Education Institute• Computer Assembly• Computer Hardware• Computer Keyboard• Computer Peripherals• Computer Printers• Computer Ribbon• Computer Ribbon Reinking Or Refilling• Computer Stationery• Computer Stationery & Imported Hardware
Parts• Computer Terminals• Computerised Washing Machine (Automatic)• Computer Software• Condenser For Motor Using Mpp Film• Control Panel Board• Cooling Coil For Air Conditioners• Copper Strip Coil From Scrap• Cordless Telephones• Cyber Cafe• Cyberkiosk • Data Processing Centre • D.C. Micro Motors
• D.G.Sets• Display Systems (Led Type)• Dish Antenna And Cable T.V. Network
Equipment• Distribution Transformers & Repairs• Domestic Electrical Appliances- Room Cooler,
Washing Machine, Water Heater, Electric Room Heater
• E-Commerce/Business• Electric Energy Meter• Electric Fans• Electric Horn For Automobile• Electric Lamp/Gls (Incandescent Lamp)• Electric Mixer• Electric Motors Up To 10 Hp. Rewinding Of All
Types Of Motors Water Pumps • Electric Motor Winding (For Fan, Mixies, Etc.)• Electric Steam Iron• Electrical Appliances• Electrical Fixtures• Electrical Stamping• Electrolytic Capacitors• Electromagnetic Relay• Electronic Balast/Chok• Electrical Choke• Electronic Digitalwatches• Electronic Digital Weighing Machine• Electronic Fire Alarm• Electronic Gas Stove Lighters• Electronic Phones, Dry Battery Packs And
Chargers/Adapters• Electronic Pressure Indicators, Electricals,
Electronic Liquid Level Indicators, Electronic Temperature Indicator, Digital Tachometer
• Electronic Telephone Instruments• Electronic Toys• Electronic Watches & Clocks• Fax Machines• F.H.P Motors• Floppy Diskettes• Fluorescent Lamp Starter• Fluorescent Tubular Lamps With Introduction To
Mercury Vapour Lamp• Franchisee Computer Education Centre (Rs.
10000)• Gas Detector (L.P.G)• Generator Set & Pump Sets• Generator (Battery Operated)• Gis Service Centre (Geographical Information
Systems) • Hardware Fitting For Transmission Line
(Overhead Line Material• Headers For Transistor Ics Semi Conductor• H.T & L.T Insulators• H.T & M.V Industrial Cubical Switch Board• Information Moving Display (L.E.D Type)• Insurance Claim Processing Centre (Eou) (Rs.
10000/-)• Integrated Circuits• Internet Based Stock Trading (Rs. 10000/-)• Internet Service Provider (I.S.P.)• Jelly Filled Telephone Cables• Lap Top Computers• Lead Acid Batteries• Lead Acid Battery Plates And Assembling Of
Battery• Legal Transcription & Secretarial Services Center (Eou)(Rs. 15000/-)• Light Emitting Diodes (L.E.D)• Linear Ics Trainer Kit• Loud Speaker• L.T Transformer Repairing• Medical Transcription Centre• Metal Film Resistors• Metallised Polypropylene, Polyester Film
Capacitor• Mica Base Electronic Components
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Mica Paper Waste Paper From Mica Waste• Micro Processors Trainer Kits Based On Micro
Processors• Mini Computer (Personal Computer)• Miniature Circuit Breaker (M.C.B)• Miniature Watch Batteries (Button Cell)• Mixer/Grinder (Mixi)• Mono Chrome Computer Monitor• Motor Start Electrolytic Capacitor• Multi Layer P.C.B• Multiple Relay For Low Voltage• Neon Indicator• Neon Sign Manufacture• Optical Fibre Cables• On Line Shopping Mall (Rs. 10000/-)• Opto Mechanical & Electrical Equipments• Photo Colour Lab• Picture Tube (B/W)• Plain Paper Copier• Plastic Film Capacitors• Polyester Capacitors• Portable Generator Set• Portal• Portable Television(Tv)• Power Capacitors• Power Inverters• Power Plant (Gas Based)• Power Plant (Hydro Based)• Power Transformers Up To 600 Kva• Printed Circuit Board • Pvc Wires & Cables• Pvc Pipe And Fitting• Re-Conditioning Of Picture Tube• Resin Cast Ct & Pt (1 Kv)• Semi Conductor Device• Semi Conductors For Transistors & Diodes• Setting Up Of A Video Studio• Smoke Detectors• Solar Cells• Solar Modules• Solar Power Plant (Energy)• Solar Photo Voltaic System• Solder Fluxes• Solar Water Heating Panels• Steel Furniture & Electrical Appliances• Stereo Amplifiers• Stereo Cassette Recorders/Players• Street Light Fittings Surge Suppressor• Tantalum Capacitors• Teflon Coated Electric Cable• Telemedicine (Distance Health Care) (Rs.
10000/-)• Telephone Cord/Cable• Telephone (Push Button Type)• Telephone (Push Button & Cordless)• Television (Ctv & B/W)• Television (3-D)• Television Deflection Components• Television Signal Boosters• Television Tuners• Traction Batteries• Training Institute Of Medical Transcription• Transformer For B/W Tv• Transformer For Voltage Stabilizer & E.H.T• Transmission Power Line Fitting• Transmission Tower Fitting• T.V. News Channel• Tv Audio Equipment Cabinets & Their
Assembling Unit• Un-Interrupted Power Supply (U.P.S)• Variable Frequency• Variable Voltage A.C. Drive• Video Cassettes (Complete Manufacturing &
Assembling)• Video Cassettes Recorder (V.C.R)• Video Film Studio• Voltage Regulator For Automobiles
• Voltage Stabilizers• Voltage Stablizer & T.V. Gain Booster• Wax And Chemical Coated, Braided Tinsel Wire• Website Design & E-Mail Registering• Welding Electrodes• Wind Energy Power Project (10 Mw) • Wire Wound Potentiometers• Wire Wound Resistance
• Alcoholic Beverages & Venegar From Coconut Water
• Alcohol Drinks From Ethyl Alcohol By Mixing Of Various Flavours
• Amla Fruit Products With Preservation Tomato Sauce, Pickles Jam And Jellies
• Anti Scale Compound For Adding Into Sugar Juice Boiling
• Apple Juice Concentrated & Dehydrated Fruit & Vegetables
• Artificial Fish Meal For Poultry Feed• Automatic Biscuit Making Plant• Automatic Bread Making Unit• Baby Cereal Food And Milk Powder• Baby Corn• Bacteria For Cane Juice• Baker’s Yeast• Bakery Industry• Banana Puree• Barley Malt• Beer & Wine• Beer Plant (Brewery)• Bidi• Bidi & Cigarette• Biscuit Plant• Bread (Automatic Plant)• Black Pepper (Spices)• Bread And Biscuits• Breeding Farm• Broiler Chicken• Button Mushroom• Cultivation & Processing• Canning Of Rasagullas In Metal Cans • Caffein From Tea Waste• Canning Of Fruits & Vegetables• Casein From Milk• Casein And By-Products• Cashew Fruit Juice From Cashew Fruit Apple • Cashewnut Kernel Extraction From Cashewnut
Fruit• Cashewnut Shell Liquid & Kernel Processing• Cashew Feni• Catecheu (By Chemical Process)• Cattle Feed From Tapioca• Chewing & Bubble Gum
FOOD, AGRO FOOD, PROCESSED FOOD, AGRO
PLANTATION, CULTIVATION, FARMING, DAIRY/MILK, TOBACCO/PAN MASALA, BREWERY & DISTILLERY,
EDIBLE OILS, EOU FOOD PRODUCTS
AND ALLIED PRODUCTS
• Chicken/Sheep Meat Processing• Chocolate (Milk)• Cigarette And Beedies• Cocoa Butter From Cocoa Mass• Coconut Water (Coco Jal) - Packed• Coconut Products & By Products Process
Complex• Cold/Soft Drinks• Collection Of Milk And Milk Making Powder• Collection Of Milk And Packing In Polythene
Pouch (1/2 Kg.1 Kg. & 2 Kg.)• Condensed Milk (Sweetned)• Cold Storage• Confectionery Industry (Toffee & Candy, Semi-
Automatic Plant)• Confectionery Unit With Toffee, Candy, Chewing
Gum And Bubble Gum• Corn Flakes• Cottonseed Oil and Cake• Country Liquor From Molasses• Custard Powder• Cigarette• Dairy Farm And Dairy (Milk) Products
(Pasteurised Milk, Butter, Ghee, Paneer)• Dairy Farm To Produce Milk & Packing In
Pouches (50%) & Can(50%)• Dairy For Milk Processing• Dairy Farming (Buffalo)• Dairy Farming (Jersey Cow)• Dal (Pulse) Mill Unit• Dehydration Of Carrot & Garlic• Dehydration & Canning Of Fruits & Vegetables• Dehydration Of Figs• Dehydration Of Fruits And Vegetables By
Vacuum Drying Method• Dehydration Of Fruits And Vegetables By Iqf
Technology• Dehydrated Onions And Onion Powder• Drinking Water (Packaged)• Dry Ice By Breaking Of Air• Drying Of Red Chillies, Haldi, Dhania, And
Green Peas• Egg Powder (40,000 Eggs Processing Per Day)• Export Of Processed Foods And Marine
Products• Fish Canning & Pouching• Fish Farming (Prawn & Other Marine Products)• Fish Meal• Flour Mill And Mustard Oil • Flavoured Milk• Food Colour & Orasted Groundnut Gram Peas,
Etc In Pouches• Frog Legs Processing• Frozen Meats Processing• Food Flavours (Whisky) Vodka, Grape, Butter
Scotch)• Food Products Complex (Dehydrated Onions,
Garlic Powder & Flakes, Cattle Feed, Tomato Powder, Tomato Products, Canned Fruits & Vegetables, Tomato Pure, Ground Nut Oil, Refined Oil, Dehydrated Grapes Etc.
• Banana Powder & Waffers) • Freeze Drying Coffee Manufacturing Unit
(Processing) And Packaging In Glass Bottles• Fruit Juice, Jam, Jellies & Allied Products• Fruit Juice, Pickles Processing And Canning• Fruit Juice Making & Packing In Plastic
Container/Pouches• Fruit Processing (Jam & Jellies)• Fruit Pulp & Juice Concentrates• Fruit & Vegetable Drying (Freeze Drying
Method)• Ginger Oil• Ginger Paste• Ginger And Garlic Paste• Goat Farm
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
GUMS & ADHESIVES
• Goat & Sheep Farming• Gram Dall/Pulse Mill• Grape Dehydration• Hard Boiled Candy (Toffee & Candy)• Herbal Cigarettes• Honey Processing & Packaging• Honey Coated Cashewnuts, Peanuts And Other
Nuts• Ice Cream Of Different Flavours• Ice Cream Stabilizer• Ice Making Plant• Icing Sugar• Indian Made Foreign Liquor (I.M.F.L)• Instant Food (Idli Mix, Dosa Mix, Gulab Jamun
Mix)• Instant Food (Instant Food & Fast Food Parlour)• Instant Noodles• Instant Tea• Instant Tea From Black Tea• Integerated Starch Baking Powder/Yeast Industry• Integrated Unit Of Dairy Farming, Milk Collection
And Processing, Fish Farming, Poultry Farming And Hatchery
• Iodized Salt• Iodized Salt (Ordinary Moisture-Less/Free
Flowing In Plastic Bags And Containers)• Jam, Jellies, Fruit Juice & Allied Products• Katha and Cutch• Khandsari Sugar• Khandsari Sugar • Lactic Acid From White Sugar By Fermentation
Process• Lactose & By Products Processing From Milk• Liquid Glucose And Its Bye Products• Macroni And Vermicilli• Malt Extraction From Barley• Mango Processing (Mango Pulp, Juice & Slices)• Mayur Brand Type Chewing Tobacco• Mineral Water• Milk Preservation & Marketing To Whole Sellers
(Inpouch Packing By Uht Technology)• Milk Processing And Packaging Of Milk Products• Milk Products (Casein, Lactose, Ghee & Whey
Powder)• Milk Toffee • Mini Flour Mill• Mini Sugar Plant• Misri (Pearl Sugar Candies)• Modern Rice Mill• Murabba• Mustard Oil Extraction & Refining• Mutton Tallow• Namkeen Industry (Bhujia, Chana Chur etc.) • Namkeen (Kurkure Type Snack Food• Namkeen With Kurkurre Type Snack Food• Namkeen & Sweets• Natural Mineral Water and PET Bottles• Non-Basmati Rice From Paddy• Oleoresin, Essential Oil, Dyes & Powder Of
Spices• Oleoresin Extraction From Diptero-Carput
Turminatus And Pinus Khasyana• Oleoresin Extraction From Chilli• Pan Masala With Packing In Pouches And Tin
Cans• Pan Masala, Tobacco, Zarda & Kimam• Packaged Drinking Water• Packaged Coconut Water (Coco Jal)• Paneer From Milk• Pappad Plant• Pectin from Orange Peels• Papain From Papaya (Papaya Latex)• Pectin From Mango Peel Pectin From Apple
Pomace• Phyto Tea (Herbal Tea)• Pickles And Sauces• Pickles Murabba etc. (Veg. & Non. Veg.Pickles)• Piggery Meat Process
• Acrylic Adhesive• Adhesive (Different Types)• Adhesive (Fevicol Type)• Adhesive For Stickers• Adhesive Based On Vinyl Acetate• Adhesive Based On Polyurethane• Adhesive For Band Aid (Johnson & Johnson
Type)• Adhesive Industries (Laminated, Sticker,Ddl &
Other Types)• Adhesive For Gasket (Liquid/Paste)• Araldyte Type Adhesive• Alkyd Resin• Bopp Self Adhesive Tapes• Cyanoacrylate Adhesive• Ester Gums• Fevicol Type Adhesive• Guar Gum• Gum Bottle (Pvc)• Gum For Pasting Labels• Leather To Leather Adhesive• Liquid Adhesive For Corrugated Boxes• Office Paste• Poly Amide Resin• Pressure Sensitive Adhesive• Pvc Indulation Tapes• Printing Gums (Guar Gum Based)• Rubber Adhesive• Self Adhesive Labels• Starch And Dextrin Based Afhesive• Surgical Adhesive Plaster• Synthetic Rubber Adhesive• Synthetic Adhesive For Decorative Laminate
Bonding • Tapioca Starch Adhesive• Vinyl Ester Adhesive• Vulcanising Adhesive Formulation Vulcanizing
Rubber Solution/Cement For Automobile Tyre• Urea Formaldehyde Resin• Water Based Latex Adhesive
• Handmade Leather• Leather Auxillaries & Chemicals• Leather Dyes• Leather Washers • Leather Board From Leather Waste• Leather For Upholstry(Sofa)• Leather Finishing Lacquer (Nitrocellulose
Lacquer For Leather)• Leather Garments• Leather Goods• Leather Shoes• Leather Shoe & Chappal• Leather Footwears• Leather Suitcases, Briefcases & Travelling Bags• Leather Goods And Garments• Leather Garments, Shoe & Chappal• Leather Pigment Used For Colouring Of Leather• Leather Tanning• Leather Tanning & Garments (Eou)• Sheep Skin Pickling Plant• Shoe Upper• Sport Shoes (Plastic)
LEATHER AND LEATHER PRODUCTS
• Pine-Apple Juice Preparation & Packaging• Potato Chips/Waffers• Potato Powder• Pouch Filling & Packaging Of Edible Oil & Ghee• Poultry Feed• Processed Foods & Spices (Eou)• Processed Readymade Food• Processing Of Fruits & Vegetables• Puree, Paste, Juice And Ketchup From Khajoor
(Dates)• Rabbit Farming• Rasgullas Making & Canning In Metal Cans• Ready To Eat Processed Cooked Food• Ready To Eat Retort Packed Food• Ready To Eat Snack Food (Crax, Roll & Ball
Type)• Rice & Corn Flakes• Rice Noodles• Roasted/Salted/Masala,Cashew Nuts, Almonds
& Peanuts• Roller Flour Mill (Atta, Suja And Maida)• Salt Licks For Cattle• Sattu• Sausages Food Casing• Soft Drinks (Cold Drinks)• Soft Drinks Essences• Soft Drinks (Non Carbonated) Mango,Licchi,
Pineapple Flavours Frooti Type In Tetrapack)• Softy Ice Cream Cones (Fully Automatic)• Soft/Cold Drinks (Cola, Orange, Lemon Etc.
Flavours)• Soyabean Products• Soyabean Bariyan• Soya Milk & Paneer• Spices/Masala With Formulae• Spices And Namkeen (Integrated Unit)• Snack Food (Kurkure Type)• Starch & Allied Propduct From Broken Rice• Strawberry Cultivation & Processing• Sugarcane Juice Preservation• Sugar Cubes From Cane Sugar• Sugar Plant• Supari (Sweet) – Betel Nut (Synthetic)• Sweet Aroma Betel Nut• Synthetic Tallow• Tamarind Juice Powder• Tamarind Juice Concentrates• Tea & Coffee Processing & Packaging• Toffees, Golies, Candy (Hard Boiled)• Tomato Products• Tomato Ketchup, Tomato Puree and Tomato
Juice• Tomato Ketchup, Tomato Puree And Tomato
Juice (Tomato Products)• Trading Business Of Spices & Pan Masala• Tuity Fruity• Vermicilli (Including Roasted Vermicilli)• Virgin Coconut Oil• Vodka From Potatoes• Wallnut Processing• Wine, Brandy, Whisky &Champagne• Wine From Dates• Yeast From Molasses• Zarda, Kimam No. 60,90,120,160,240,300 &
400 (Tobacco)• Zarda Kimam And Tobacco• Zarda-Zafrani (Babachhaptype)
Call or SMS us on 0981143789509811151047
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
MISCELLANEOUS PRODUCTS
• Agarbatti (Insence Stick)• Abrasive Paper• Agarbatti (Mosquito Repellent)• Agarbati Bamboo Stick• Agarbatti Synthetic Perfumery Compound• Air Freshner(Odonil Type)• Air Taxi• Amusement Park• Anodic Aluminium Label• Aquaculture Prawn Farming (100% Eou)• Aqua Culture Shrimp Farming (100% Eou)• Artificial Flowers• Artificial Jewellery• Asbestos Yarn• Ash Trays For Maruti Vehicle• Air Bubble Packaging• Asphaltic Roofing Sheet (Metal Components)• Automatic Book Binding • Alkyd Resin• Apple Juice Concentrate • Ball Point Pen Fefills (Jotter Type)• Bank Branch Building• Banquet Hall• Bio-Coal Briquettes From Agriculturalcellulose
Waste• Boot Cream/Polish• Buffing & Polishing Compound• Brass Badges By Etching • Briquetted Fuel From Agro Waste• Briquetting Of Lignite Coal• Buffalo Horn Tip, Hoof• Banquet Hall• Button • Calcined Petroleum (C.P) Coke• Canvas Shoes• Canvas Shoes, Jungle Boots• Carbon Brush, Brush Holder & Slip Ring• Cement Sheets With Coir Fibre & Other
Segments• Ce ram ic Ti l es (G lazed ) By Doub le
Firing/Heating• Children Recreation Centre • Coal Briquettes • Cold Storage & Ice• Cold Storage For Fruits And Vegetables • Compressor (Hermetic) For Air Conditioner• Costume Jewellery/Imitation Jewellery• Decorative Laminated Sheet (Sunmica)• Dental Colleges• Diamond Cutting & Exports• Drinking Straw From Propylene• Engineering College• Engineering College, Management Institute,
Cbse School, Hostel (Boys And Girls), Medical College With Hospital And Research Institute
• Electropolishing On Gold Jewellery (Gold Ornaments)
• Entertainment Club• Fashion Technology Institute• Fast Food Parlour• Fast Food (Instant Food & Fast Food Parlour)• Fire Extinguishers (Soda Acid Type)• Fish Net• Floriculture (Cut Flower Rose) With Green
House• Floor Covering Sheet• Film Studio (Video)• Flush Door, Chip Board, Wood Wool & Other
Insulating Boards• Gas Detectors Of L.P.G • Gems Manufacturing
• Glass Bottle By Scrap• Glass Jars Manufacturing Plant For Packaging
Of 50, 100, 150, 200 Grams Coffee Packaging• Goat & Sheep Farming• Gold Electroplating• Gold Jewellery (E.O.U)• Gold Plated Silver Jewellery & Cutlery• Granite Slab And Tiles• Granite Mining• Green House• Hard Chromium Plating• Health Club And Beauty Parlour Cum Hair
Saloon With Sona Bath• Health Club Cum Beauty Parlour Training
Institute• Horn Tip,Hoove Button• Hospital• Hospital (100 Beds)• Hospital (200 Beds)• Ice Making Plant• Imitation And Costume• Jewellery (Necklace, Earrings Ear Top Etc.)• Initmate Scent Chemicals From All Types Of
Flavour• Investment Casting• Jute, Coir, Glass Rope/ Sutli• Jute Twine• Jute Bags From Yarn Without Spinning Process• L.P.G Bottling Plant• L.P.G Regulator (Domestic Purpose)• Laminated Particle Board & Hard Board• Laminated Safety And Toughened Glass• Leasing & Hire Purchase• Lichen (Charila)• Manila Ropes• Medical College• Medical University• Metal Pretreatment Chemicals Powder, Coating
Chemicals• Match Unit From Waxed Paper• Medium Density Fibre Board• Melamine Crockery• Mineral Water• Mini Cement Plant• Mirror Silver, Golden, Pink, Black & Smokes• Modern Advertising Agency With Dtp & Film
Studio• Motel/Small Hotel• Multi Colour Printing• Multi Purpose Cold Storage And Dehydration
And Canning Of Fruits And Vegetables• Multi Storey Commercial Complex Alongwith
Residential And Delux Flats For Foreign Tourists & Revolving Restaurent At The Top
• Multiple Lamination Industry • Mushroom Growing And Processing (By Deep
Freezing Method)• News Paper Printing• Nickel Lined Industrial Screen• Non Coking Coal To Coking Coal• Nursing Home• Offset Colour Printing Press (Six Colour)• Offset Printing Press• Old Age Home• P.C.C Electric Poles• Photographic Developer & Fixer• Pvc Extrusion Profile (Door & Windows)• Pop-Corn• Photo Etching Of S.S.• Pre Stressed Cement Concrete Pipes• Pilfer Proof Caps• Pilfer Proof Caps And Crown Cap • Pouch Making & Gravure Printing (Roto Printing) • Poultry & Fish Farming (Integerated Unit)• Printing Of Tin Sheets• Radio Station• Radio Taxi
• Readymade Garments• Refractories With Ceramics• Restaurant• Rose Plantation And Rose Oil Extraction • Rotogravure Printing• Safety Belts• Safety Matches• School• School With Hostel• Shoe Laces• Silk Cocoon Cultivation (Growing Of Silk
Cocoon Warm)• Silk Screen Printing Formulations For Plastic,
Paper & Cloth• Spikenard (Jatamansi)• Stencil Coating Solution• Sugar Candy (Misri)• Sugar Cane Plantation• Sugar Cane Juice Preservation• Super Speciality Diagnosis Centre• Surat Zari• Synthetic Shoes & Soles• T.V. News Channel• Tea Packaging Industry• Toughened Glass• Tennis Balls• Three Star Hotel• Travelling Agency• Trays, Trolleys For Hospital With Scratchless
Coating• Wax Extracts (Tanning Powder)• Wire Rope Slings• Wood Wool Slab• Wooden Cane Furniture With Export Potential• Wooden Door And Windows• Wooden Furniture • Wooden Panel Including Kiln Seasoning• Wooden Furniture• Watch Case Buffing• Watch Dial• Wrist Watches• Watches (Electronic)• Zedoary (Kachur)
Over30,000
PROJECTS REPORTS
Aailablewith
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
EDIBLE OILS, ESSENTIAL OILS LURICATING OILS, GREASES,
VEGETABLE OILS, WAXES, CAMPHOR, PERFUMES &
PERFUMERY COMPOUNDS AND REFINED OILS ETC.
EDIBLE OILS, ESSENTIAL OILS,
LURICATIING OILS, GREASES, VEGETABLE OILS,
WAXES, CAMPHOR, PERFUMES & PERFUMERY COMPOUNDS
AND REFINED OILS ETC.• Aromatic Perfumery Compound• Aerosol• Agarbatti Perfumery Compound• Bees Wax Manufacture• Camphor• Cardanol From Cashew Nut Shell Liquid• Castor Oil• Castor Oil Derivative Oleoresins• Chilli Oil• Citronella Oils• Clove Oil• Concentrate Of Rose Jasmine & Lily Etc.• Coloured Flame Candle• Candles (Semi-Automatic)• Corn Oil (Maize Oil)• Dehydrated Castor Oil • Eugenol From Cinnamon Leaf Oil• Extraction Of Essential Oil (Cardamon, Jeera,
Ajowan, Ginger Oils Etc. & Packaging Of Ground Spices)
• Extraction Of Jasmine Essence• Extraction Of Essential Oils By Super Critical
Fluid Method From Flowers, Herbs & Spices• Eucalyptus Oil • Extraction Of Oil From Oil Seed Expander
Extrusion Technology)• Fat Liquor Sulphated Oil• Flavours For Food• Fish Oil• Garlic Oil & Powder• Ginger Oil, Sandalwood Oil And Nagarmotha Oil• Ginger Oil• Ginger Oil & Ginger Dust• Ground Nut Oil• Integerated Wax Complex• Ionone From Lemon Grass Oil• Jasmine & Lilly Flower Oil• Lemon Grass Oil• Liquid Paraffin• Lube Oil & Grease • Lubricating Oil • Menthol Crystals• Menthol Oil & Crystal• Micro Crystalline Wax• Mustard Oil (Edible Oil)• Oleoresin From Spices• Oil From Artemisia Herbs• Palm Oil Crushing Unit
• Pan Masala• Paraffin Wax• Paraffin Wax From Slack Wax• Perfume For Food Industries With Pan Masala
Perfume• Pouch For Oil And Ghee Packaging• Refined Oil-Sun Flower Oil, Groundnut Oil, Staff
Flower Oil & Cotton Seed Oil• Refined Vegetable Oil• Reclamation Of Used Engine Oil• Rice Bran Oil (R.B.O)• Rose Oil Extraction• Smoke Less Candle• Spice Oil & Oleoresins• Solvent Extraction Plant (Oil Cake Based)• Synthetic Almond Oil• Synthetic Wax• Synthetic Tallow• Synthetic Ghee• Synthetic Musk• Turmeric Oil Oleoresin • Vanilla Cultivation And Extraction/Processing• Vegetable Oil Extraction & Refining
• Nickel Plating Brightener • PCB With Grasphite & Silver Coating • Rainbow Colours On Metal • Silver Refining By Electrolysis & By Acid • Silver Extraction • Silver Extraction From Waste Hypo Solution • Silver & Gold Plating On PVC & Nylon-6 • Tin Printing • Titanium Jewellery Plating • Vacuum Metallizing • Zinc Electroplating Brightner • Zinc Electroplating On Nut, Bolts,
ELECTROPLATING, ANODIZING &
ALLIED PROJECTS
PAINT, ENAMEL, SOLVENTS, THINERS, INKS & VARNISH PAINT, ENAMEL, SOLVENTS, THINNERS, INKS & VARNISH• Acrylic Emulsion Paints• Acrylic Cement Paint (Dry Powder)• Aluminium Paint• Automobile Paints• Ball Point Pen Refill Ink• Bituminious Road Emulsion• Bitumen• Bituminious Felts For Water & Damp Proofing• Bituminious Road Emulsion Rapid Medium &
Slow Setting• Buffing & Polishing • Cement Paint For White & Grey Cement• Dispersant• Dry Distemper• Dry Distemper & Cement Paint• Duplicating Ink Black For Gestner Duplicator• Emulsion Paints (Water Based)• Hammertone Paint• Insulating Varnish & Wire Enamel• Iron Oxide Pigments• Insulating Varnish (Poly Vinyl Butyral Based, Ffc
Grade)• Lime Colour (Cement Colour)• Synthetic Red Oxide For Floorings• Solvent & Thinners• Marking Inks (Water Proof)• Metal Naphthanate (As Drier For Paints)• N.C. Putty• Offset Printing Ink• Oil Bound Distemper Paint• Paint Brushes• Paint Manufacture For Rolling Coating Of
Aluminium And Steel Coil• Paint Removers• Paint Industry• Paint & Varnish• Picture Varnish• Powder Coating Paint• Printing Inks (Offset,Flexo & Roto Gravure)• Primer Paint & Enamel Paint• Putty & Water Proofing Paint• Printing Inks (Flexo-Graphic Ink)• Putty (Metal Casement) • Red Oxide Primer (Anti Corrosive)• Refractory Paint (Graphite Based)• Screen Printing Inks• Silk Screen Printing Ink Formulation For Plastic,
Paper, Cloth• Stamp & Pad Ink• Stoving Paint • Spirit Soluble Maleic Resin• Texture Paint• Thinners And Its Allied Products• Toner Ink • Varnish Thinner (Solvent)• Vacuum Metallizing Lacquers• Wood Primer
FISH FARMING AND FISHERY PRODUCTS
• Aquaculture Prawn Farming (Fresh Water)• Chitin & Chitosan from Prawn Shell Waste • Chemicals From Prawn Fish Head • Developing Trout Fish Preservation &
Storage And Marketing Infrastructure • Fish Farming • Fish Canning And Pouching • Fish Processing (Blast Freezing Process)• Fish Net • Fish Oil Soap • Fish Meal • Hdpe Fishing Net • Plastic Milk Crate And Plastic Fish Crate• Trout Fish Farming, Canning & Preservation
With Aqua Feed Manufacturing (Integrated Complex)
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
4449, Nai Sarak, Main Road, Delhi-110006 (India)
Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361 Email : [email protected],
[email protected] Website : www.eiriindia.org, www.eiri.in,
www.eiribooksandprojectreports.com
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
PHARMACEUTICAL, DRUGS, AYURVEDIC/HERBAL COSMETICS & MEDICINES, HOMOEOPATHIC MEDICINES, HOMOEOPATHIC
MEDICINES, DISPOSABLE SYRINGE, DENTAL COLLEGE
& FINE CHEMICALS ETC. MEDICINES, HOMOEOPATHIC
MEDICINES, DISPOSABLE SYRINGE, DENTAL COLLEGE
& FINE CHEMICALS ETC.
• Aromatic Pills • Alumina From Bauxite• Aspirin • Ayurvedic Pain Balm Ointments• Ayurvedic Churan And Tablets• Ayurvedic Tablets (Hajmola Type)• Ayurvedic/Herbal Pharmacy• Ayurvedic Sherbats• Ayurvedic Products• Bulk Drugs (E.O.U)• Blood Bags• Calcium Gluconate• Capsule, Tablet & Injection With Modern
Instruments • Cashew Feni• Chloroquinone Phosphate (Bulk Drugs)• Clinical Thermometer• Dental Clinic• Dental College• Dental Grade Eugenol• Dextrose Monohydrate, Liquid Glucose• Dehydrated Onion & Onion Powder• Dextrose Powder (Anhydrous From Starch)• Dextrose Saline Solution• Distillery (I.M.F.L)• Disposable Needles For Syringes• Disprin• Distilled Water• Empty Hard Gelatin Capsules• Fairness Cream• Filling & Packing Of Capsules• Glucose - D - Powder• Glycerine • Hair Colour Mate (Formulations And Process
Only)• Herbal Cosmetics• Herbal Shampoo• Herbal Shampoo And Cream• Herbal Hair Oils (Ayurvedic)• Homoe & Bio-Medicines With Mother Tincture• Homoepathic Medicines• Hypodermic Needles • I.V. Fluids• Ibuprofen• Infusion & Transfusion Sets (I.V. Set)• Injectable For Pharmaceuticals• Injection Ampoules Packaging Box• Integerated Surgical Cotton
• Ice Making Plant• Ice & Cold Storage• Lactose & By Products Processing From Milk• Lichen (Jatamansi Charila)• Liquid Glucose And Its By-Products• L-Lysine Monohydro Chloride• Liquid Glucose From Potatoes• Medical College• Methanol (Hpcl Grade)• Nicotine From Tobacco Waste• Ointment-Ayurvedic (Yellow & White)• Pharmaceutical And Food Grade Gelatine• Pharmaceutical Industry (Tablets, Capsules,
Liquid, Gel, Ointment Powder Injectable)• Pharmaceutical Unit (Eou) With Formulations,
Injectables, Etc. Pyridine & Derivatives• Salt (Iodized Salt)• Saline & Injection Water• Saline Water & Dextrose Solution (I.V.Fluid In
Plastic Bottles)• Sorbitol• Starch (Maize)• Surgical Adhesive Plaster • Surgical Bandages• Surgical Gloves• Surgical Cotton• Surgical Cotton And Bandage• Synthetic Camphor Powder• Tablets & Capsules • Tissue Culture• Tincture From Rectified Spirit• Trimethopime• Veterinary College With Hospital• Veterenary Medicines (Only Formulations)• Vitamin ‘C’, Sorbitol’ Anhydrous Dextrose, Starch
• Ammonia Paper• Automatic Book Binding • Adhesive (Fevicol Type)• All Pin & Gem Clips• Ball Pen• Ball Pen Refill Ink• Ball Pen Ink Remover• Carbon Paper• Card Board• Carbon Less Paper • Cellphane Paper• Computer Continuous Stationery• Computer Forms & Security Printing Press• Corrugated Board & Box (Printed & Laminated)• Corrugated Board And Boxes From From Card
Boards• Corrugated Cartons From Plain Papers• Corrugated Paper• Corrugated Packing & Material (Bulb & Tubes
Packing)• Desk Top Publishing • Defoaming Agent For Paper Plant• Drinking Straw Paper
PULP, PAPER, STRAW/GREY BOARD, KRAFT PAPER, PACKAGING, PAPER CARRY BAG,
PAPER FROM AGRO WASTE &
STATIONERY ETC.
• Duplex Board• D.T.P Cum Offset Press• Egg Trays From Pulp• ECG Paper• Exercise Note Book, Register And Pad • Flexographic Ink• Greeting Card By Offset Press• Hand Made Paper Filter Paper• Hard Board• Hard Board From Bagasse• Injection Ampoules Packaging Boxes• Insulatiing Paper• Kraft Paper• Kraft Paper From Bagasse• Laminated Packaging Paper With Printing • Lamination & Coating On Paper• M.G. Paper From Waste Paper• Mill Paper From Waste Paper• Mill Board From Rice & Wheat Straws• Mill Board From Waste Paper• Mini Paper Plant From Sisal• Mini Paper Plant• Multi Wall Paper Sacks• News Paper For Children• N e w s P r i n t P a p e r F r o m R i c e
Straw/Bagasse• News Paper Childrens • News Print Paper• Offset And Treadle Type Printing Press• Mill Board Based On Rice Straw• Paper And Board From Straw• Paper & Paper Products• Paper Envelopes• Paper Carry Bags • Paper Board Carton• Paper Cones For Loud Speakers• Paper From Akra• Paper From Bagasse With Corrugated Board &
Boxes• Paper From Bamboo• Paper And Pulp• Paper Glasses For Beverages• Paper From Rice Husk & Wheat Husk• Paper From Tree Bark, Eucalyprus Wood• Paper Products• Paper Plant (White Writing & News Paper For
Pulp & Waste Paper)• Paper Plates, Paper Glass• Paper Cones & Tubes• Paper Plant With Dtp & Printing & Publishing
Unit• Paper Based Phenolic Sheet• Paper Waste Recycling (Paper Mill)• Paper Cup For Ice Cream• Paper Tubes Spiral Winding Composite
Container• Paper Lable For Beer Bottles• Particle Board & Block Board With Sanding &
Lamination Of Particle Board• Particle Board From Rice Husk• Pouch Filling & Making For Tomato Sauce• Pouch Making & Gravure Printing• Processing Of Paper For Feeding In Computer• Pulp From Bamboo & Wood• Paper Files• Playing Cards• Rosin Sizing Agent (For Paper Plant)• Sand Paper• Sanitary Napkins• Silicon Coated Paper• Stencil Paper• Straw Board And Grey Board• Straw Board & Mill Board• Straw Board And Paper Board • Tissue Paper Facial• Tissue Moist Toiletery Cleansing Tissue And
Related Products
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Tissue Paper Rolls• Tetra Pack For Milk Packaging, Ghee & Other
Liquids• Toilet Paper Rolls• Toilet Paper & Napkins• Wax Coated Printed Paper • Wet Face Freshner Tissue• White Writing & Printing Paper• Writing & Printing Paper (Paper Mills)
• Abs Granules From Abs Scraps • Acrylic Beads• Acrylic Copolymer Emulsion• Acrylic Latex• Acrylic Sheet• Acrylic Sheet & Moulded Products• Acrylic Teeth• Air Bubble Packaging Film• Audio Cassettes Parts By Injection Moulding• Audio Cassettes Assembly And Recording• Auto Tubes• Auto Flaps For Trucks & Buses• Auto Tyre & Tubes• Baby Bottles (Plastic) With White silicon Rubber
Nipples• B.O.P.P. Film• B.O.P.P. Pressure Sensitive Self Adhesive Tape• Baby Nipple (Silicon)• Baby Nipple (Big Size)• Ball Pen Manufacturing (Automatic Plant)• Bath Tub (Acrylic)• Balloon Plastic Advertising• Blister Film PVC• Blister Packaging & Pouch Packaging• Blow Moulding Plastic Container• Coating On Metalized Polyester Film/Metallized
Paper/Aluminium Foil• Coating On Plastic (Electrolysis) & Glass• Co-Extruded Multilayer (5-Layer) Film with
Printing• Coir Foam (Rubberised)• Colour Coating On Plastics• Colour Master Batches For Various Plastics• Crumb Rubber• Cycle Tyres And Tubes• Discount/Credit Card• Disposable Plastic Cups Glasses, Etc.• Disposable Plastic Syringes & Needles• Disposable Plastic Syringes• Disposable Plastic Razor• Dough Moulding Compound (D.M.C)• Egg Trays From Plastic• Epoxy Resin• Expanded Polyestrene Moulding (Thermocole)• Fibre Glass Sheet
PLASTIC, B.O.P.P. ACRYLIC, DISPOSABLE PLASTIC PRODUCTS,
PET PRODUCTS, P.V.C. H.D.P.E. P.P. L.D.P.E. P.U. A.B.S.
THERMOFOARMING, MASTER BATCHES & POLYMER AND RUBBER PRODUCTS, TYRE,
TUBE, ADHESIVE, SHEET, COIR & MANY OTHERS
• F.R.P Auto, Scooter Roofs & Ceilings• FRP Pipes And Products• F.R.P Products (Helmet, Washbasin Sheets,
Roofing Sheets)• Fibre Reinforced Plastic (High Pressure
Moulding With SMC BMC And DMC)• Field Rubber Converted To The 60% Latex
Rubber• Flexible P.U. Foam• Formaldehyde Crockery & Other Items• Formaldehyde Resin (Urea, Phenol, Melamine)• Gasket Sheet• Gum Bottle (PVC)• Glass Beads• Helmet• HDPE Coated Paper Sack• H.D.P.E. Bags• H.D.P.E. Containers (Blow Moulding)• H.D.P.E. Container, Poly Jars By Injection
Moulding (Food Grade)• Hdpe Fishing Net• H.D.P.E. Jerry Cans• Hdpe Manufacturing From Ethyl Alcohol• H.D.P.E Pipe And Fittings• H.D.P.E. Pipes• H.D.P.E Printed Bags• H.D.P.E Twines And Ropes• H.D.P.E. & L.D.P.E Pipes And Fittings• H.D.P.E/Pp Box Strapping• H.D.P.E/Pp Woven Sacks Using Plain Looms• Hologram Stickers-3d• H.M Bag Plant With Printing Unit• Hawai Chappals (Rubber)• I.V Plastic Bottle• Ice Cream Cup (Plastic)• Injection Moulded Auto Components• Injection & Blow Moulded Plastic Products• Injection Moulded Plastic Products • Integerated Complex Ester’s & Allied Products
(D.O.P,D.B.P, & Ethyl Acetate, Buytl Acetate, Wire Enamels, Jelly Cable Compound)
• L.D.P.E. (Low Density Poly Ethylene) Granules From Virgin (L.D.P.E. Resin)
• Integerated Surgical Rubber Goods Industry• Injection Moulded Plastic Balls• L.D.P.E From Ethyl Alcohol• Ldpe Moulded Products• Lamination Ofcoextrusion Multilayer Film In Roll
Form• Latex Rubber• Latex Rubber Condom• Master Batches (Coloured, P.V.C, L.D.P.E,
H.D.P.E, Etc.)• Melamine Formalhyde Resin• Melamaine Crockery• Moulded Luggage• Multi-Layer (3 Layer Bags)• Multi-Layer (3 Layer) Film With Lamination &
Printing• Nylon Net For Giving Shade To Tea Plant In
Nursery• Oil Seal• Pet Bottle/Containers• Pet Bottles And Caps• Pet Bottles From Pre Form• Pet Bottle & Mineral Water• Pet Granules (Dana)• Pet Pre-Form From Pet Resin• Pet Pre-Form Cum Pet Bottles• Pet Pre-Form Pet Bottles Cum Mineral Waters• Plastic Crayon• Poly Carbonate Resin • Ptfe Components• Polythene Shopping Bags• Pu/Pvc Sole For Sport Shoe By Imported M/C.• Pvc Battery Separator• P.V.C Compounds (Fresh)
• P.V.C Compounds (Scrap)• P.V.C Electrical Insulating Tape• P.V.C. Extrusion Profiles• Pvc Film• P.V.C Fittings• P.V.C Flexible Fusible Powder Heat Fusible
Powder• PVC Footwear• P.V.C Granules (For Insulation & Sheets
Grades)• P.V.C Granules From Pvc Scraps (With Pollution
Control)• P.V.C Hoses• P.V.C Leather Cloth• P.V.C Flexible Pipes• P.V.C Pipes And Fittings • Polythene Bags (Printed)• Pvc Plastics Film Sheet Soft/Rigid• PVC Resin And Compound • PVC Rular• PVC Stablizers (Single Pack System)• PVC Wire And Cables• Paper Based Phenolic Sheet For Electrical • Phenol Formaldehyde Resin• Phenolic Resin• Plastic Beads From Plastic Scraps • Plastic Buttons• Plastic Cans• Plastic Collapsible Tube• Plastic Corrugated Sheet & Boxes • Plastic Film And Sheets With Printing Flexo &
Roto/LDPE/HDPE/PP/HM/PVC• Plastic Filter Masterbatch & Other Master
Batches For Various Plastics • Plastic Doors (Sintex Type)• Plastic Jerry Cans• Plastic Granules Or Powder From Plastic Scrap• Plastic Injection Moulded T.V. Cabinets• Plastic Items Manufacture From Powder
Melamine• Plastic Goods • Plastic Pipes & Tarpaulins• Plastic Sheet From Scrap• Plastic Plant (Blow Moulding & Injection
Moulding)• Plastic Products (Gold, Silver, Nickel)• Plastic Toys • Polyester Beading • Polyester Film • Polythene Bags & Automatic Printing• Polythene Printed Bags• Polyurethane Foam And Its Products• Propylene Film (Printed) & Bag Manufacturing• Plastic Mats• PVC Wire And Cable• PVC Pipe And Fitting• Polythene Shopping Bags• PVC Profiles (Door and Windows)• Resin Coated Sand • Rexine• Rexine Cloth & Allied Products• Rubber Adhesive• Rubber Auto Parts• Rubber Belting• Rubber Powder• Rubber (And Metal Bonded) Auto Parts• Rubber Moulding Unit Including Lining Rubber
Sheeting• Rubber Reclaiming• Rubber Rollers For Textile Mills & Paper
Industries• Rubber & Plastic Sheets, Mats & Flaps• Rubber Sheet And Allied Hospital Rubber Goods• Rubberized Pvc Gasket• Rubberised Coir• Rubber Compound For Automobiles• Safety Belts• Silver And Gold Plating On Pvc And Nylon-6
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Silicone Rubber Nipples/ Teats• Smart Card• Spectacle Frames (Plastic)• Spunge Rubber• Surgical Examination Gloves• Synthetic Pearl Coating On Polystyrene Beads• Synthetic Rubber Adhesive • Teflon Manufacturing• Teflon Tape• Teflon Tapes & Cables• Thermocole Sheet And Moulded Products
Expanded Polyesterene Extrusion Profiles• Thermoformed Packaging (Blister Packaging &
Pouch Packaging)• Thermoplastic Polyurethane• Thermoformed Cups, Plates & Glass With Hips
Sheet• Thermocole• Thermocole Based Disposable Glass, Cups &
Plates• Tooth Brushes• Toy Balloon, Decora Tive & Industrial Balloons• Tread Rubber• Tyre Retreading (Hot)• Tyre Retreading By Cold Process• Tyre Tubes & Flaps• Tyre & Tubes• Unsaturated Polyester Resin• Unsaturated Polyester For Rexine• V-Belt And Fan Belt• Vinyl Asbestos And Pvc Wall Paper• Viton (Fluoro Elastomer)
• Acid Slurry, Synthetic Detergent Powder• Acid Slurry• Agarbatti Synthetic, Perfumery Compound+• Aromatic Perfumery Compound• After Shave Lotion• Antiseptic Cream• Bath Soap (Various Types)• Beta Ionone• Bleaching Powder • Blue Detergent Powder• Cleaning Powder (Vimtype)• Cold Cream• Coloured Flame & Perfumed Candles (Red,
Blue, Green Flame)• Cosmetic Industry (Modern)• Cosmetic Industry (Shampoo, Spray Perfume,
Talcum Powder• Detergent Powder (Ariel Type)• Detergent Powder (Nirma Type) Fully Automatic
Plant• Detergent Washing Powder• Detergent Cake And Powder• Fairness Cream• Fish Oil Soap• Glycerine Transparent Soap• Hair Removing Cream• Herbal Cosmetics• Herbal Shampo & Cream• Herbal/Ayurvedic Cosmetics• Incense Powder,Incense Sticks & Incense
Cake• Nerol Soap• Oil Soap• Optical Whiteners• Rose Oil Extraction • Shampoos (Coconut Oil Based Cold Process)• Shaving Cream• Sindur (Kumkum)
SOAP, DETERGENTS, COSMETICS & PERFUMES
• Soap Coated Paper• Spray Dried Detergent Powder• Stain Remover• Synthetic Detergent (Blue Powder)• Toilet Soap And Glycerine Soap• Toilet Soap From Soap Noodles• Talcum Powder (Face & Toilet Powder)• Toilet And Herbal Soap• Tooth Paste & Powder• Washing Detergent Powder And Washing Soap• Washing Powder Liquid Detergents,Lotion &
Shampoo
• Angora Rabbit Wool• Bed Sheet, Bed Cover, Sofa Cloth, Curtain Cloth
(Home Furnishing)• Buckram• Canvas Shoes, Jungle Boot, Boot Rubber
Knees & Boot Combat• Carpet From Cotton Waste• Ceramic Thread Guide• Cotton Buds/Swabs• Cotton From Waste Yarn• Cotton Rolls• Cotton Saree• Cotton Spiders For Loud Speakers• Denim Cloth• Denim Cloth (Integerated Unit With Bleaching,
Dyeing And Printing)• Dispersent For Textile• Dyeing & Bleaching• Dyeing Of Hank Yarn• Emulsifier For Wool Batching Oil• Embroidery On Fabrics• Garment Dyeing, Washing & Stitching (Jeans,
Jackets, Skirts & Shirts)• Goves Knitting• Gunny Bags • Hdpe/Pp Woven Sacks• Hdpe Tarpaulins Using Plain Loom With
Lamination• Hdpe/Pp Woven Sacks Using Circular Looms• Hosiery Cloth (Cotton) Processing (Bleaching,
Dyeing, Finishing Of Cloth)• Hosiery Industry • Hosiery Mercerising• Hosiery Products Like Vest, Brief, T-Shirts &
Socks• Jacquard Fabrics• Jute Coir, Grass Rope/Sutli Making• Jute Felt• Jute Twines• Knitted Fabrics
TEXTILE INDUSTRIES, READYMADE GARMENTS,
COTTON, DYEING, BLEACHING, CLOTH,
HOSIERY, POWER LOOM, HAND LOOM,
WOOLLEN, SILK, SOCKS, SURGICAL
COTTON & MANY OTHERS
• Laminated Jute Bags• Lamination Of Hdpe Woven Cloth (Jute,Cotton,
Paper)• Nylon Yarn Crimping, Doubling And Bleaching• Pigment Binder For Textile Printing• Polyester Resin For Wire Enamel• Polyester Resin• Polyester Yarn From Waste Polyester Zip
Fasteners• Power Loom• Printing On Saree• Readymade Garments & Hosiery• Readymade Garments Merchandise• Readymade Garments & Covers• Readymade Garments & Embroidery Of Gowns,
Shirts, Blouses, T-Shirts Etc. (Only Ladies)• Readymade Salwar Suit• Ready Made Garments• Recovery Of Nylon From Nylon Waste• Rotary Printing And Dyeing On Cotton, Synthetic
Textile• Sanitary Napkins• Screen Printing On Cotton Cloth• Sewing Thread Reels & Balls Making Industries• Screen Printing On Cotton, Polyester & Acrylic• Shawls (Woollen)• Shoe Laces• Silk Fabrics On Handloom• Socks Knitting• Spinning, Doubling Dyeing, Mercerising &
Bleaching Of Cotton Yarn• Spinning & Carding Of Wool Into Yarns• Starch Book Binding Cloth• Surat Jari• Surgical Cotton & Bandage• Synthetic Textile Industry (Suiting, Shirting,
Sarees) Terry Cloth• T-Shirts• Towels, Bed Sheet Covers• Terry Towel• Terry Fabrics Weaving Unit• Textile Auxilliaries & Chemicals• Textile Bleaching, Dyeing & Finishing & Printing
Of Cotton Fabrics• Textile And Finishing Agent• Textile (Hosiery)• Textile Mill• Textile Dyeing & Printing• Textile Printing (Job Work)• Textile Pigment Printing Binder• Towel (Terry)• Velvet Cloth By Flocking Process• Viscose Staple Fibre• Wadding Oil (100%) For Wadding Of Cotton
Hosiery Cloth In The Dyeing Process• Weaving Of Dasuti Cloth With Printing, Dyeing,
Embroidery & Finishing • Washing Of Jeans & Other Garments• Worsted Woollen Yarn Cloth• Zari Glitter Salma Sitara Of Plastic Film
AXIS Bank Ltd............
............CA-054010200006248
ICICI Bank Ltd. ..........
.................CA-038705000994
Union Bank of India...
...........CA-307201010015149
State Bank of India....
...................CA-30408535340
HDFC Bank................
.............CA-05532020001279
Yo
u c
an
de
po
sit
th
e a
mo
un
t in
EIR
I a
cc
ou
nts
eit
he
r in
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Amusement Park• Aided School• Amusement Park Cum Water Park • Banquet Hall• B.Ed And Law College• Business Process Outsourcing (Bpo)• Call Center (Domestic)• Call Center (International)• Children Recreation Centre• Cold Storage• Community Hall• Community Centre• Computer Education Institute• Computer Software• College• Club• Cyber Café• Data Processing Centre• Dental Clinic• Dental College• Diagonostic Centre• E-Commerce/Business• E-School (Rs. 10,000/-)• Engineering College• Entertainment Club• Entertainment Club, Holiday Resort, 4 Star
Hotel, Amusement Park Cum Water Park, Mushroom & Its Products, Fish Farming, Lake For Boating, Deer Park
• Fashion Technology Institute• Fast Food Parlour• Five Star Hotel• Food Parlour• Franchise Training Programme For Iit &
Engineering Entrance Exams.• Golf Course• Health Club, Beauty Parlour• Health Club And Fitness Center• Health Resorts• Holiday Resorts• Holiday Resort Cum Entertainment Club With 4
Star Hotel• Hospitals• Hospital Cum Research Centre• Hospital (400 Beds)• Ice Cream Parlour• Internet Service Provider (I.S.P.)• I.T. Park (Infotech Park)• Maternity Nursing Home• Medical College• Medical College, Hospital & Research Institute• Medical Transcription Centre• Mental Retardation Hospital & Cerebral Palsy• Motel/Small Hotel• Multistorey Commercial Complex• Multistorey Residential Complex• Multiplex Cum Entertainment Centre• Nursery School• Nursing School/College• Nature Care Centre• Nursing Home• Old Age Home• Online Shopping Mall (Rs. 10,000/- Report)• Portal
INFOTECH/IT, HOSPITALITY, HOSPITAL, COLLEGE, SCHOOL, MEDICAL, ENTERTAINMENT,
CLUB, WARE HOUSING & REAL ESTATE PROJECTS.
• Pre-Fabricated Building• Prenursery School• Rehabilitation Centre For Aged & Needy
Persons• Residential Cum Commercial Complex• Restaurant• Restaurant With Pub • Senior Secondary School• Special Economic Zone (Sez)/Industrial Park• School (Primary)• School (Higher Secondary)• School With Hostel• School Of Nursing• Three Star Hotel• Township• Tourist Club• Training Institute For Medical Transcription• Video Film Studio• Vetenary College With Hospital• Ware House• Website Design & E-Mail Registering
• Alcohol From Potatoes • Dextrose Powder From Potatoes • Frozen Finger Chips • I M F L (Whisky) From Potatoes • Liquid Glucose From Potato • Potato Chips/Waffers • Potato Powder (Automatic Plant) • Potato Starch • Potato Chips (Automatic Plant) • Potato And Onion Flakes • Potable Beer (Alcoholic) Based On Potato &
Barley/Malt • Potato Powder • Sago Seeds (Saboo Dana) • Vodka From Potatoes
POTATO AND POTATO BASED PRODUCTS
• Coal Briquettes From Agrowaste • Furfuralfrom Ricehull• Mushroom Cultivation & Processing (Button)• Mushroom Growing & Processing With Air
Conditioning• Mushroom Cultivation & Processing Unit
Dehydration & Packaging Of Oyster & Paddy Straw Mushrooms
• Organic Manure• Papaya Cultivation• Papaya & Tomato Cultivation• Processing & Utilisation Of Coconut• Processing Of Sheep Hair To Produce Wool• White Oats
AGRO BASED INDUSTRIES
• Agrolactor Soya Milk • Automatic Biscuit Naking Plant• Automatic Bread Making Plant• Apple Fruit Juice With Canning Bottling• Ayurvedic Sharbat• Bakery Unit (Pastries, Bread, Buns, Cake, Toffee
Etc.)• Baking Powder • Banana & Its By Products• Banana Powder• Banana Wafers
BAKERY, CONFECTIONERY & FOOD PRODUCTS
• Banana Cultivation• Beer Industry • Dehulling Of Jaun For Beer• Beer & Wine• Beer, Alcohol, Imfl• Besen Plant• Biscuit Plant• Bread & Biscuit Plant• Bottling Plant (Country Liquor) From Rectified
Spirit• Bottling Plant (Imfl And Country Liquor)• Brandy • Bread Rusks• Buffalo Meat/Frozen Meat With Slaughter House• Canned Fruits & Vegetables• Canning & Preservation Of Meat • Canning & Preservation Of Vegetables• Canning Of Mango Pulp & Mango Slices• Carbonated Beverags• Cashew Feni• Cashew Nut (Dried & Fried)• Cashew Nut Shell Liquid And Kernel • Cattle Breeding• Cattle Breeding & Dairy Farm To Produce Milk • Cattle Feed From Tapioca• Chewing Ginger & Amloki• Chewing Gum• Chilli Sauce• Chilli Powder• Chicken Processing With Slaughter House• Chocolate• Cider Plant• Cocoa Powder• Cocoa Butter & Cocoa Powder• Coconut Shell Powder• Coconut Water • Coconut Sweet (Watery)• Coconut Milk Powder (Dehydrated)• Coconut Products & By Products (Integrated
Plant)• Cold Drink • Curry Powder• Dairy For Milk Processing (Ghee, Butter &
Paneer)• Dairy Products• Dairy Products Milk Packaging In Pouch (Ghee,
Butter, Etc.• Dairy Farm To Prduce Milk With Packaging
(Cow) • Dairy Farm To Prduce Milk With Packaging
(Bufalloe) • Dairy Farm & Milk Products• Dal Moth, Chanachur & Bhujiya• Dall Mill (Pulse)• Dehydration Of Fruits & Vegetable • Dehydration Of Fruits And Vegetables By
Vacuum Drying Method• Desiccated Coconut Powder From Coconuts• Dehydration & Canning Of Fruits & Vegetables• Dry Fruit Roasting & Packaging• Drying Of Red Chillies, Haldi, Dhaniya, Peas &
Ground Nut • Dry Ginger (Ginger Powder)• Egg Powder• Fish Canning In Tin & Pouches• Fish Dehyration (Drying Of Fish)• Fish Meal • Fish Processing (Beast Freezing Processes)• Flavours For Food Industries• Flour Mill (Roller)• Frozen Meat• Food Dehydration (Fruits & Vegetables)• Fried & Roasted Ground Nut, Grams, Pear Etc.• Fruit Juice Making & Packaging In Plastic
Container• Fruit Juice In Tetra Pack (Drinks)• Fruit Juice, Squashes, Sauce & Ketchup, Jam,
Jelly, Vinegar Etc.
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Garlic Flakes• Garlic Powder• Ghee & Butter• Ginger (Pulverised)• Ginger Glazing & Preservation• Ginger Storage• Ginger Processing• Ginger Oil & Ginger Dust• Ginger Powder (Dry) & Oleoresin• Grape Dehydration• Grape Cultivation• Grape Juice • Grape Wine• Groundnut Processing• Honey Processing & Packaging • Ice Cream & Ice Candy• Ice Cube• Invert Sugar• Idli Mix, Dosa Mix Sambhar Mix, Vada Mix,Gulab
Jamun Mix• Instant Coffee & Instant Tea• Instant Noodles• Instant Soups• Iodized Salt From Crude Salt• Jam Chutney Pickles & Squashes• Katha Manufacturing • Lecithin (Soya Based)• Lemon & Its Products• Macaroni Manufacturing • Macaroni, Spaghetti, Vermicelli & Noodles• Maize & Its By Products Malting Plant• Mango Pappad (Aam Pappad)• Mango Powder Ripe• Mango Powder• Mango Processing & Canning (Mango Pulp)• Meat Processing (Chicken Mutton)• Meat Processing (Buffalo)• Menthol Bold From Menthol Flakes• Milk Powder• Milk Powder & Ghee• Milk Powder, Ghee & Spices• Milk Preservation & Marketing To Whole Sellers • Milk Preservation & Marketing To Whole Sellers
(In Pouches)• Milk Toffee Manufactures• Mineral Water• Mineral Water In Pouches• Mini Flour Mill Atta Maida, Suji & Wheat Bran • Mithai/Halwai (Sweet & Namkeen)• Mutton Processing• Pan Masala (Meetha, Sada, Zarda) Making &
Packing• Pan Masala And Pouch Making • Paneer (Cheese)• Papad & Bariyan• Papad Plant• Pepsicola In Polytubes • Petha Packaging • Pickles• Piggery/Meat/Chicken Processing• Pine Apple Juice Manufacturing And Canning• Potato & Onion Powder• Potato & Onion Flakes• Potato Chips• Potato Granules• Pouch Filling For Saunf Supari Ilaichi Etc.• Preservation Of Raws Mango Juice• Processed Cheese & Marine Pdts.• Pulp From Tarmarind • Readymate Processed Food • Rice & Corn Flakes • Rice Basmati (Trading)• Rice Polishing & Packaging In Pouch• Roasted/Salted/Masala/Cashew Nuts Almonds
& Pea Nut• Roller Flour Mill • Vanaspati Unit
• Medical Transcription• Business Process Outsource (BPO)+• Data Processing Centre• E-Commerce• Cybercafe• Computer Software• Internet Service Provider (Isp)• I.T. Park• Computer Education Centre• Portal (Website Design)• Call Centre (Domestic)• Call Centre (International)
INFOTECH/IT PROJECTS
• Activated Carbon • Adhesive (Fevicol Type) • Agarbatti Perfume Compound • Air Conditioners • Aluminium Foil • Automatic Biscuit Plant • Acid Slurry • Aluminium Wire Drawing • After Shave Lotion • Ayurvedic Medicine • Aluminium Utensils• Auto Tube • Bakery Unit• B. Ed & Law College
• Beer Plant • BOPP Self Adhesive Tape • Brick • Buffaloe Meat • B.P.O. • Bread • Banana Powder • Cattle & Poultry Feed • Ceiling Fan • Call Centre • Candle • Castor Oil • Coconut Oil • Cold Drink • Computer Software • Confectionery • Corn Flake • Corrugated Box • Cyber Cafe • Chewing Tobacco • Calcium Carbonate • Coolant • Cigarette • Cosmetic • Cement • C.P. Bathroom Fitting • Chrome Plating • Copper Wire Drawing • Coated Paper • Carbon Paper • Cycle Tyre & Tube • Disposable Syringe • Dairy Products • Detergent Cake & Powder • Detergent Powder • Ethanol • Extraction Of Essential Oil • Emulsion Paint• Eucalyptus Oil
160 NEW EXPORT ORIENTED UNITS & MOST PROFITABLE PROJECTS
• Eva Inject • Exercise Note Book & Register • Egg Tray • Electric Switch Etc. • Foundry • Fiber Glass • Floriculture • Fruit Juice • Food Dehydration • Fish Farm • Food Procesing • Garlic Oil • Goat & Sheep Farm • Gold Electroplating • Gold Cyanide Powder • Ginger Oil • Ginger Process • Guar Gum • G.I. Wire • Handmade Paper • Herbal Cosmetic • Holiday Resorts • Hdpe/Pp Bag • Herbal Extracts • Ice Cream • Isp • Jam, Jelly, Chutney Etc. • Denim Cloth • Leather, Garments, Shoes & Chappals • Lube Oil And Greases • Liquid Adhesive• Leather Adhesive • Latex Condom • Mcb • Musical Bell • Mini Flour Mill • Mango Processing • Medicinal Plant Extracts • Medical Transcription • Menthol Crystal • Mineral Water • Mosquito Coil • Motel • Mushroom • Masala • Mustard Oil • Management Institute For Mba, Bba, Bca,
B.Com• N.C.Putty • Namkeen Industry • Nut, Bolt, Rivets And Washers• Oleoresin • Oil Seals • Paper Glass • Processed Cheese • Pan Masala • Paper Bag • Pappad • Pet Bottles • Pet Bottles From Pre-Form • Pickle, Muraba & Sauce • Plastic Toy• Plywood • Ply-Bamboo From Bamboo (Bamboo Panel/Boards/Floorings)• Potato Chips • Pouch • Poultry Farm • Paint • Paper Carry Bags • Plastic Injection Moulding • Plastic Tanks H.D.P.E • Plastic Mat • P.V.C. Pipe/Fittings • P.V.C. Film • Pressure Cooker • Potato Powder
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in
LIST OF ALL THE AVAILABLE FOLLOWING PROJECT REPORTSPROJECT REPORTS
PROJECT PROPOSALS FOR SELECTION OF A GOOD INDUSTRY
• Amla Plantation • Amla Plantation, Processing & Preservation • Bio Fertilisers • Coffee Plantation • Coconut Plantation • Dairy Farming • Eucalyptus Tree Plantation • Floriculture - Gladiolus • Goat Farming • Green House • Hybrid Seeds • Herbs Cultivation • Jatropha (Bio Diesel) Cultivation & Extraction • Mushrooms • Mushroom Growing And Processing With Air
Condition • Medicinal Plantations (Neem) • Nursery Farms • Organic Manure • Papaya & Tomato Cultivation • Papaya Cultivation • Poplar Plantation • Rubber Plantation • Strawberry Cultivation & Processing • Safed Musli Cultivation & Processing (Extract
& Powder) • Stevia Cultivation & Extraction • Sunflower Plantation • Sugar Cane Plantation • Teak Plantation • Turmeric Plantation • Tea Plantation • Vermi-Composting
PROFITABLE PLANTATION, CULTIVATION AND
FARMING PROJECTS
• Adhesive For Stickers • Adhesive For Corrugation Dry Powder & Paste • Adhesive Based On Polyure Thane• Adhesive Industries (Laminated, Favicol,
Sticker, Dda & Other Types Of Adhesives)• Adhesive For Corrugation (Dry Powder)• Alkyd Resins • Adhesive Manufacturing For Joining Hdpe Pipes & Joints • Adhesive Based On Vinyl Acetate (Fevicol Type)• B.O.P.P Self Adhesive Tapes • Cnsl Based Resin In Liquid & Powder Form • D.O.P And Other Plasticizers • Ester Gums (Food Grade) • Epoxy Resin • Guar Gum • Glue Stick • Latex Rubber Based Adhesive • Leather Based Adhesive • Liquid Adhesive For Corrugated Board & Boxes • Leather To Leather Adhesive (Latex Based
Adhesives) • Melamine Formaldehyde Powder • Office Paste • Paper Label For Beer Bottles • Polyester Resins • Phenol Formaldehyde Resin • Potato Starch
PROFITABLE GUMS, ADHESIVES &
RESINS PROJECTS
• Poly Amide Resin • Printing Gums (Guar Gum Based)• Rubber Adhesive • Synthetic Adhesive For Decorative Laminates
Bonding • Starch & Dextrin Based Adhesive• Thermosetting Adhesive • Urea Formaldehyde Resin • Urea Formaldehyde Moulding Powder • Unsaturated Polyester Resins • Water Based Latex Adhesives
• Caffeine From Tea Waste • Decaffineated Tea • Instant Tea And Coffee (Premixed With Sugar
And Milk) • Instant Tea From Black Tea • Tea Bags (Dip - Dip Types) • Tea Botique • Tea Packaging Industry• Tea Bags • Tea Packaging & Distribution• Tea Industry
TEA PLANTATION AND PROCESSING BASED
INDUSTRIES
• Aluminium Powder • Aac & Acsr Aluminium Conductors • Aluminium Silicate • Aluminium Utensil • Aluminium Wire Drawing • Aluminium Paint • Aluminium Ingots From Scrap • Aluminium Alloy & Ingots • Anodizing Of Aluminium • Aluminium Chloride • Aluminium Channels • Aluminium Rolling Mill • Aluminium Bottles • Alumnium Foil Cutting & Roll Making • Aluminium End Caps • Aluminium Door And Windows • Aluminium Collapsible Tubes • Aluminium Phosphide • Aluminium Ingots From Bauxite • Aluminium Caps • Aluminium Furniture & Hardware • Aluminium Beverage Cans • Aluminium Cans For Capacitors • Aluminium & Aluminium Alloys From Aluminium
Scraps To Make Utensils (Induction Furnace Melted)
• Aluminium Hot & Cold Rolling Mill (Aluminium Sheets & Circles)
• Anodic Aluminium Labels • Aluminium Slugs & Circles • Alluminium Printing Plate For Offset Printing
Machine • Aluminium Foils • Aluminium Wire And Rods • Brass and Aluminium Hinges • Hard Anodizing On Aluminium • Pilfer Proof Caps • Piston Assembly (Aluminium Alloy) • Pressure Die Casting (Aluminium) • Paper Coated Aluminium Wire • Pressure Cooker
ALUMINIUM AND ITSBASED INDUSTRIES
TERMS AND
CONDITIONSPrice of Rs. 11700/- for
Each MARKET SURVEY CUM DETAILED
TECHNO ECONOMIC FEASIBILITY REPORT
or Rs. 25000/- for EXHAUSTIVE
DETAILED PROJECT REPORT Payable in
advance through Bank Draft/Cash in favour of
ENGINEERS INDIA RESEARCH INSTITUTE, Delhi. Delivery by Regd. Post/Courier within 3-4
days.
4449, Nai Sarak, Main Road, Delhi-110006 (India)
Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361 Email : [email protected],
[email protected] Website : www.eiriindia.org, www.eiri.in,
www.eiribooksandprojectreports.com
AXIS Bank Ltd............
............CA-054010200006248
ICICI Bank Ltd. ..........
.................CA-038705000994
Union Bank of India...
...........CA-307201010015149
State Bank of India....
...................CA-30408535340
HDFC Bank................
.............CA-05532020001279
Yo
u c
an
dep
osit
th
e a
mo
un
t in
EIR
I acco
un
ts e
ith
er
in
www.eiribooksandprojectreports.com
Market Survey Cum Detailed Techno Economic Feasibility Report on all Projects are available contact:
ENGINEERS INDIA RESEARCH INSTITUTE4449, Nai Sarak, Main Road, Delhi-110006 (india) Ph. : 9811437895, 9811151047, 91-11-23918117, 23916431, 23947058, 45120361
Email : [email protected], [email protected] Website : www.eiriindia.org, www.eiribooksandprojectreports.com www.eiri.in