Sensor Report - MQ3 Gas sensor - NYIT Logo (New York...
Transcript of Sensor Report - MQ3 Gas sensor - NYIT Logo (New York...
Project Report
Alcohol Detecting System
EENG-491-w02
Advisor: Tao Zhang
Member: Haotian Kong, Rui Xue, And Ji Dai
May 13, 2013
Table of Contents
1. Introduction ………………………………………………… 3-4
1.1 Background ………………………………………………... 3
1.2 Motivation ………………………………………………………...… 3
1.3 Objective ……………………………………………………………… 3
2. Design Approach ………………………………………….…. 4-5
3. Key factors on the research ………………………….…………...5-9
3.1 Influence of alcohol on human ……………………..………….....5-6
3.2 Alcohol Concentration change in weight…………………………..6-8
3.3 The time after one drank ……………….………………….…….8
3.4 Law of different countries ………………………….…………………..9
4. Hardware ……………………………………………………...…9-14
4.1 MQ3-sensor ………..………………………….…………………….....9-11
4.2 Arduino Mega …………………………………………………….12-13
4.3 BlueSmirf Silver Module ………………………….…………………13-14
2
5. Software……………………………….…………..……………15-18
5.1 Software part—Arduino software ……..……………….………………….15-16
5.2 Android Programming ……………………………..……………….…..16-18
6. Project Demonstration …………………………………………..19-20
7. Future Plan ………………………………………………...20-22
8. Cost …………………………………………………………22
9. Summary …………………………………………………....22
10.References and Attachments ………………………………….…23-29
1. INTRODUCTION
1.1 Background
Drunk driving is a very dangerous behavior. People will become slow in reacting and
can’t control their actions. Drunk drivers’ aren’t able to deal with the emergency
situations when they are driving. The investigation done by the World Health
Organization in 2008 shows that about 50%-60% of traffic accidents are related to
drunk driving. The drunk driving has been listed as the main reason for the fatal car
accident.
1.2 Motivation
These years, the cases of traffic accident caused by drunk driving have increased
rapidly. More and more people have realized that the drunk driving does great harm to
public security. It’s time to develop a kind of system which can stop the drunk driving
effectively. As this kind of system hasn’t been popularized, we try to develop this
system which is available on every car. This system won’t cost much, but it will bring
much for it concentrates on human’s safety. This system has a preventative effect
which can stop accidents from the beginning.
3
1.3 Objective
We want to design a kind of system which can detect the alcohol concentration in the
cars to prevent the behavior of drunk driving. The system consists of these parts:
1. Sensor Part--used to detect the concentration of alcohol in the air and send the
concentration in the form of voltage signals to the following part.
2. Processing Part—used to receive the voltage signals and process the signal to
analog signals that can be standard for the concentration of alcohol.
3. Display Part—used to get the processed signal and show the data to users in the
form of diagrams.
The sensor will be fixed near the driver’s seat. The driver should breath to the system
before he (she) starting the car. If the concentration of alcohol detected is below the
allowable standard, the car can be started normally. If the concentration of alcohol is
above the allowable standard, the system will send alarm to the driver. The
concentration of the alcohol will be showed in diagrams which can be seen on the
driver’s cellphone.
The system should be safe, sensitive, accurate, convenient and cheap. This kind
of system can be fixed on every car to ensure the driver’s driving safety and can
protect the passengers’ walking safety.
2. DESIGN APPROACH
The following block diagram shows the sketch how we design the system.
4
Figure 1.flow chart of Alcohol detecting system
The flow chart above shows the main structure of the alcohol detecting system. From
this chart we can briefly know the components we have used and how to connect
them. Here is the introduction of the usage of each component:
1. MQ-3 alcohol sensor: This sensor can detect the value of the alcohol
concentration in the air and transform this value to voltage signals. The sensor
should be powered and the pin on the sensor which is used to send out the voltage
signals should be connected with the analog-in pin on the Arduino board.
2. Arduino board: We chooses the Arduino Mega ADK as the developing board for
it has more pins and has more advanced chip with more flash memory which can
reach almost all of our requirements in the research period. With the help of
Arduino board, we can transform the uncountable voltage signals to countable
analog signals which range from 0 to 1023. The operating voltage is 5V. So the
real voltage of the input voltage is: (Output analog value/1024)*5V. After the
Arduino board has completed the data processing part, it would send the signals to
the cellphone with the help of Bluetooth module.
3. Bluetooth module: Bluetooth module can help the system reach wireless
connection. This means we needn't take pains to try to connect the cellphone with
5
Arduino board by cockamamie wires. This design can let the system become more
humanized.
4. Android phone: Smart phone is a wide platform for developers to design
applications. We have designed an application that can let the value of alcohol
concentration showed in visual diagrams instead of analog signals. And because
the cellphone is a good medium that can contact with others by messages or the
Internet, the statistics can be shared easily.
3. KEY FACTORS ON THE RESEARCH
—Blood Alcohol Concentration
3.1 Influence of alcohol on human
Alcohol will influence human’s behavior. One drinks more, one would be dizzier.
Terrible traffic would occur because of drunk driving. From the chart blows, we can
see the influence of alcohol on human behavior in details.
0.02 — 0.03 BAC: No loss of coordination, slight euphoria and loss of shyness.
Depressant effects are not apparent. Mildly relaxed and maybe a little lightheaded.
0.04 — 0.06 BAC: Feeling of well-being, relaxation, lower inhibitions, sensation of
warmth. Euphoria. Some minor impairment of reasoning and memory, lowering of
caution. Your behavior may become exaggerated and emotions intensified (Good
emotions are better, bad emotions are worse)
0.07 — 0.09 BAC: Slight impairment of balance, speech, vision, reaction time, and
hearing. Euphoria. Judgment and self-control are reduced, and caution, reason and
memory are impaired (in some*states .08 is legally impaired and it is illegal to drive
at this level). You will probably believe that you are functioning better than you really
are.
0.10 — 0.125 BAC: Significant impairment of motor coordination and loss of good
judgment. Speech may be slurred; balance, vision, reaction time and hearing will be
impaired. Euphoria. It is illegal to operate a motor vehicle at this level of intoxication
6
in all states.
0.13 — 0.15 BAC: Gross motor impairment and lack of physical control. Blurred
vision and major loss of balance. Euphoria is reduced and dysphoria is beginning to
appear. Judgment and perception are severely impaired.
0.16 — 0.19 BAC: Dysphoria predominates, nausea may appear. The drinker has the
appearance of a "sloppy drunk."
0.20 BAC: Feeling dazed/confused or otherwise disoriented. May need help to
stand/walk. If you injure yourself you may not feel the pain. Some people have nausea
and vomiting at this level. The gag reflex is impaired and you can choke if you do
vomit. Blackouts are likely at this level so you may not remember what has happened.
0.25 BAC: All mental, physical and sensory functions are severely impaired.
Increasing risk of asphyxiation from choking on vomit will seriously injure you by
falling or other accidents.
0.30 BAC: STUPOR. You have little comprehension of where you are. You may pass
out suddenly and be difficult to awaken.
0.35 BAC: Coma is possible. This is the level of surgical anesthesia.
0.40 BAC and up: Onset of coma, and possible death due to respiratory arrest.
In sum, alcohol will negatively affect your behavior. The more you drink, you will be
more easy to be wild.
3.2 Alcohol Concentration change in weight
There are far variables involved to accurately estimate or predict a person’s BAC
simply based on gender. The data is so important for us to build a accurate project
design.
7
Figure 17.Concentration of alcohol vs. consume number and weight-men
Figure 18.Concentration of alcohol vs. consume number and weight-women
The drink chart displayed above provides a rough estimate of a person's blood
8
alcohol level (BAC). it is based on the number of drinks consumed and the person's
weight. The red number in men chart shows you cannot drive in such a concentration.
The purple number in women chart means you have out of control and driving skills
have been significantly affected. The bigger you are, the more difficult you will get
drunk. Our design is open to all people, so we consider the weight into account.
3.3 The time after one drank
As the following figure19, it’s also an important factor for calculating the
concentration of alcohol in one’s body. From the chart above we find the relationship
versus the weight and the consumed number. One will get lower concentration of
alcohol as time passes, which will affect the measurement of our system. Based on the
chart, we calculate the relationship between the concentrations of alcohol and the time
after you drank.
Figure 19. Hours to zero BAC for men and women
9
3.4 Law of different countries
Figure 20. Different standard among different countries
The standard of legitimate centration of alcohol before driving is different among
different countries. If one is from the USA and one is from China, they will under
different limitation.so it’s also an important factor. After our calculation, we find, for
Chinese, if the display is larger than 75, our system will make an alarm.(for
USA:140,for Canada:104)
4. HARDWARE
4.1 MQ3-sensor
4.1.1 Introduction of MQ3
In this sensor, there’s a little white tube in the middle of sensor. Basically, this tube is
a heating system that is made of aluminum oxide and tin dioxide and inside of it there
are heater coils, which practically produce the heat. And you can also find 6 pins. 2
pins that I called Pin H are connected to the heater coils and the other ones are
connected to the tube.
The core system is the cube. As you can see in this cross-sectional view, basically,
10
it is an Alumina tube cover by SnO2, which is tin dioxide. And between them there is
an Aurum electrode, the black one. And also you can see how the wires are connected.
Basically, the alumina tube and the coils are the heating system, the yellow, brown
parts and the coils in the figure2
Figure 2. Inside the sensor
The MQ-3 is an alcohol gas sensor that is available for about $5 from sparkfun.
It’s easy to use and has sparked the imagination of anyone who has dreamed of
building their own Breathalyzer device for measuring the amount of alcohol in the
human body. We got five MQ-3 sensors a couple of months ago and have spent a lot
of time trying to figure out how to do this. After lots of “data gathering”, we found
that this task is not as easy as it sounds.
4.1.2 Circuit of sensor connection of MQ3
As shown in Figure3, The
other part of the circuit is
essentially a variable
resistor inside the sensor.
The resistance across an A
pins and a B pin varies
depending on how much
alcohol is in the air in the
11
sensor. The more alcohol, the lower the resistance is. We measure alcohol in the
breath by measuring this resistance. Instead of measuring the resistance directly, we
measure the voltage level at the point between the sensor and a load resistor.
First, we use 5v. And as you can see one of H pins goes to the power and the
other one is connected to the ground. And the pin A is connected between the power
and the pin H and the pin B is goes to the microcontroller. Also between the ground
and the Arduino, you need the resistor. Before you connect the resistor if you use the
pot, you can tune the resistor for getting more accurate values. In the datasheet they
say you can used 100k om to 470k om. So we use 220k om in our circuit.
It will react that depending on the environment, it gives us little bit of different values.
But in our experiment, it gives me 200 as the lowest value and 700 as the highest
value. And when it detects the alcohol in the air, actually it is pretty sensitive, the
value gets higher very quickly but you have to wait for about 10 seconds to reset it. So
that means getting values is fast. And the sensitivity of this sensor is affected by time
span. When I used three different sensors, the range of value was a little smaller than
the new one's. But it doesn’t affect the whole experiment.
4.1.3 Reaction Theory of MQ3
SnO2 ceramics will become the semi - conductor, so there are more movable
electrons, which means that it is ready to make more current flow.
Then, when the alcohol molecules in the air meet the electrode that is between
alumina and tin dioxide, ethanol burns into acetic acid then more current is produced.
So the more alcohol molecules there are, the more current we will get. Because of this
current change, we get the different values from the sensor.
4.1.4 Detail of Sensor Connection
As the figure 4 shown, We put the H (left)
connect the 5.0V and H (right) to the ground
(GND). We can choose either A or B as one
of the analogin pin to connect the Arduino
board. And use another one, B or A, just
12
opposite to the former one, we can only use 4 of 6 pins in the project.
4.2 Arduino Board
4.2.1 Introduction of Arduino mega
Arduino Mega2560 microcontroller board is an easy-to-use development board based
on the Atmel ATmega2560 MCU. The ATmega2560 has 256 KB of flash memory for
storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM, and 4 KB of
EEPROM. The Arduino Mega2560 microcontroller board has 54 digital input/output
pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs
(hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack,
an ICSP header, and a reset button. The Arduino Mega2560 contains everything
needed to support the MCU. Simply connect it to a computer with a USB cable or
power it with a AC-to-DC adapter or battery to get started. This Arduino development
board is compatible with most shields designed for the Arduino Duemilanove or
Diecimila. The Arduino Mega2560 differs from all preceding boards in that it does
not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8U2
programmed as a USB-to-serial converter. The Arduino MCU board includes a
number of facilities for communicating with a computer, another Arduino, or other
MCUs.
4.2.2 Sampling rate in the Design
Delay() is a key function to arrange the frequency of reading in the while loop.
Once the loop starts, the analogRead() function will sample the data from sensor and
by delay(100) function, delay 100ms, then next sample data comes in.
In our project, we use the analogread() in the
arduino, the Arduino board contains a 16 channel
(8 channels on the Mini and Nano, 16 on the
Mega), 10-bit analog to digital converter. It will
map input voltages between 0 and 5 volts into
integer values between 0 and 1023. It gives us
readings of: 5 volts / 1024 units or, .0049 volts
13
(4.9 mV) per unit. The input range and resolution can be changed using
analogReference().
It takes about 100 microseconds (0.0001 s) to read an analog input, so the
maximum reading rate is about 10,000 times a second. It returns int (0 to 1023).
4.3 Bluetooth Silver Module
The baud rate is quite important to be set in Arduino code part. At the first, we use the
blue tooth module to test, the baud rate we
set is 9600, that is suitable for the
connection. But when using Bluetooth silver
module, the baud rate should be 115200 .
Here’s the Connection the bluesmirf silver
Bluetooth, as shown in the figure 6. There’re
6 pins in the Bluetooth Silver Module, we use the middle of them, the sequence is
VCC, GND, TX and RX, TX and RX means the transmit port and receive port which
should be connect to the receive port and transmit port in the arduino board.
As the following figure 7 and figure 8, BlueSmirf Bluetooth Module should
have 115200 baud rate which should modify before we use it. When the BlueSmirf
14
Bluetooth Module paired with your device, the green light is on. The picture Figure 7,
shows the baud rate in the arduino code, the figure 8, shows the reading board in the
computer.
5. Software part
5.1 setting of environment
5.1.1 Arduino software
It is the most complicated part of this experiment. We get the detailed tutorial from
http://arduino.cc/en/main/software. There’re four kinds of operating system for you to
choose. Basically, the software helps us input the code into the arduino board, which
shows the corresponding alcohol reading result of MQ3 (sensor).
As shown in figure 9, after placing the folder into the libraries folder, we should
be able to access all the amarino files through the arduino programming environment
and then open the code in arduino board.
Figure 9: SensorGraph code in Arduino
5.1.2 Installing Amarino
We download the following
applications on your mobile phone
1. Amarino – Android Application- to
be installed on phone.
15
2. Amarino Plug-in Bundle- to be installed on phone.
3. Amarino Library- To be kept in Java Project
5.1.3 Eclipse and ADT
It is the most complicated part of this experiment. The basic idea is to Install the
Eclipse first (follow the system requirements), then install the android SDK, then
install ADT plugin for Eclipse IDE. Codes still need to be changed to realize the
function and is shown in the end of the manual.
5.2 Android Part
5.2.1 Structure of Android programming
Android programming based on the Java SE platform, we design the project as seven
parts, Alarm, Amarino, AmarinoIntent, Country, GraphView, SensorGraph and
StartingPart.
Figure 11. The brief structure in Android programming
The Country.java and StartingPart.java, we set these activities to let the user
16
choose the country they have to fit the different criteria the application has. As you
can see in the following picture:
When you want to arrange the sequences of your
activities (it’s the name of android interface), it should be
set in the AndroidManifest.xml, that’s the different
between Java and Android.
And In order to let the country.java become the first,
we should press the following code, let the <intent-
filter></intent-filter>inside the first activity we want to
show to the user.
Then the GraphView.java and SensorGraph.java shows the actual diagram can show
to the user,
17
Finally, we set the criteria as 500 to alarm because it can show you the brief
change in each time. Once the reading touches 500, it will alarm at once.
18
Then open the apk file and install the application “alcohol detection” into smart
phone. We use the Samsung S1 GT-I9100 android version is 4.2.2, processor is
ARmv7 Processor rev 1(v71).
5.2.2 Problems in software design
1. In the code part, in order to make the activity act like a window, not extend the
whole screen, we can set the androidManifest.xml as /theme.Dialog.
Figure 15. Theme.Dialog in xml file
2. When we use the application in virtual smart phone, it may show us the error
process, as shown in the figure 16.
3. We should check the androidManifest.xml to make sure that each activity has
settled already.
4. Layout is a very important part in
android design, the label and
arrangement of buttons and texts are all
depend on these file, when we set the
function in activity, we should set the
corresponding part in Layout, and then,
it will yield the ID in the “R.class” in
Gen fold. And during the programming,
R.class will disappear automatically,
then we found if you have unlogical
code in layout.xml, it can be done.
19
6. PROJECT DEMONSTRATION
Figure 21. Alcohol detecting system
From the demonstration we can see that our alcohol detecting system has the
following advantages:
1. The materials are cheap and are easy to acquire. The cost of this system is one of
the important factors we are considering. Because if we want to popularize this
system, we should make it as cheap as possible so that every driver can afford of
20
this useful system.
2. It doesn’t some large measuring instruments which mean it can be made small
enough and can be put into production without any challenging technological
problems.
3. We used the Bluetooth module. It can realize the wireless communication. It is a
significant design because we can use the smart phone to receive the signals and
do further designs.
4. Smart phone is a wide platform for us to design more humanized applications to
fulfill user’s requirements. In our system, we have transformed the abstract analog
signals to visual diagrams. And the smart phone will send alarm to users when the
alcohol concentration reaches a certain value.
5. We can also share the value of alcohol concentration from the drivers to their
relatives, friends or the police. Because the data can be showed on cellphones, we
can send the date by the Internet or message.
7. FUTURE PLAN
These are what we have done up to now. In the future, we will:
7.1 Try to reduce the cost of the system when it can be made as a product.
This is a system that can be used in everyday life for everyone. So users must be
concerned with the cost of the alcohol detection system. The cheaper it is, the more
chance it will be popularized. Because our system is in the period of experiment and
design, the cost may be higher than the modified products. We are using Arduino
Mega ADK as the developing board. It is expensive because it is appropriate for us to
learn how to use developing board and is convenient to connect the wires with the
sensor and the Bluetooth module. In future, we can design a printed circuit board to
simplify the circuit and use a small chip instead of the developing board. Based on the
technology of manufacture nowadays, the total cost of a finished product will be less
than $20. This price is low enough which almost every driver can afford of this
21
system.
7.2 Make it small enough and more convenient to use.
The smaller and more convenient the
alcohol detection system is, the more likely
drivers will accept it. Up to now we have
come up with several options to place it on
the car:
1. The first option is that we can set it on
the keychain, the system is as small as a
key and the driver can blow it directly.
So the drivers won’t take pains to refit the car.
2. Another option is that we can put a cable near the driver’s seat and the cable is
connected with the ignition of the car. This means the alcohol detection system
can be another key to the car. The driver should blow to the system before he/she
start the car. If the value of the alcohol concentration is above a certain value, the
system will stop the car starting. So a drunk driver won’t be able to start the car
which will prevent the behavior of drunk driving. It is not only safe to the driver,
but can ensure the passengers won’t be hit because of the driver’s drunk driving.
Figure 22. Connect with car ignition
3. We can also design it as a plug-in unit. It can be plugged with a cellphone or on
the console of the car. This design can ensure a tiny size of the system. And the
system can be used as an USB stick that means the data can be stored in it and we
22
can plug it with relevant terminal to do more calculations.
Figure 23. Plug the iphone
4. Fixing the alcohol detection system on the driver’s seat is also a wise choice.
Because the sensor near the seat can detect the driver’s breathe alcohol
concentration easily and the driver won’t take pains to blow to any system
intentionally.
Figure 24. Fix on the back
7.3 Improve its efficiency and accuracy to let it become more reliable.
Whether the system is accurate and sensitive can affect whether the users are satisfied
with it. Our system should tell the drivers the real alcohol concentration and whether
they can control their driving skill after they have drunk some wines. Our system
shouldn’t bring trouble to the users. Such as the system sends alarm continually and
can’t be stopped.
23
7.4 Raise its popularity by advertisements so that it can be used on every car.
It is no doubt that if a product is wanted to be popularized, it should be advertised
well. Our system is focus on detecting the driver’s alcohol concentration which can be
used on everyday life. So we should tell drivers how dangerous the drunk driving will
be and how to avoid this by fixing a tiny, cheap and accurate system. We are always
thinking about how to construct a safe driving environment to drivers.
8. COST
Figure 25. Total cost for project
24
9. SUMMARY
In this project, the most important thing is that the sensor can detect all the conditions
when driver has drunk already no matter how much they did. Secondly, connecting to
the car ignition is a proper way to force driver do so every time they want to drive.
Thirdly, user can get the data on their android phone in time when they do breathing
test every time.
We predict that alcohol detecting system can use in all cars to serve for the people
who need.
10. REFERENCES AND ATTACHMENT
1. "Sensor Report - MQ3 Gas sensor", April 27, 2008
http://sensorworkshop.blogspot.com/2008/04/sensor-report-mq3-gas-sensor.html
2. "The Jacket That Tells You You’re Drunk", October 13th, 2011
http://arduino.cc/blog/category/sensors/mq-3-alcohol/
3. Blood/Breath Alcohol Concentration (BAC) calculator
http://www.dot.wisconsin.gov/safety/motorist/drunkdriving/calculator.htm#disclaimer
4. "Arduino Breathalyzer: Calibrating the MQ-3 AlcoholSensor"
http://nootropicdesign.com/projectlab/2010/09/17/arduino-breathalyzer/
25
5. "Building an Breathalyzer with MQ-3 and Arduino", Mar 7, 2010
http://www.danielandrade.net/2010/03/07/building-an-breathalyzer-with-mq-3-and-arduino/
Manual of Alcohol Detecting System
Alcohol detecting systemIt’s a kind of system that detect the alcohol concentration in the cars to prevent the behavior of drunk driving.
a. android smart phone (samsung galaxy S1)b. OSX operating systemc. Arduino megad. Eclipse IDE for Java EE Developerse. Android SDKf. Amarino Tookitg. Bluetooth Medium- Bluesmirf Silver
We separate it as three parts: Laptop part, hardware part, software part
26
Step 1 : Setting up connection between Arduino board and MQ3
Sensor (hardware part)
27
Connect the Arduino borar and MQ3 in the following way:
H (left)–5.0V H (right)-GNDA (one of both A) — 5.0VB — GNDWe use 4 of 6 pins
Step 2 : Set up Arduino software (Laptop part)
It is the most complicated part of this experiment.You can get a detailed tutorial from http://arduino.cc/en/main/software There’re four kinds of operating system for you to chooseBasically, the software helps us input the code into the arduino board, which shows the corresponding alcohol reading result of MQ3 (sensor)
28
Step 3 : Downloading Meet Arduino Library (Laptop part)
Download the MeetAndroid Library and place it into the libraries Folder Arduino.
After placing the folder into the libraries folder, you should be able to access all the amarino files through the arduino programming environment.
Or import the code (sensorgraph) that lists below
Step 4 : Setting up bluesmirf silver with arduino board (hardware
part)
Connect the bluesmirf silver Bluetooth adapter in the following way:
Tx–1 to Rx–0VCC — 5.0VGND — GNDTX — RX (digital pin 0 of arduino)RX — TX (digital pin 1 of arduino)
* very very important: Your BlueSmirf Bluetooth Module should have 115200 baud rate. When the BlueSmirf Bluetooth Module paired with your device, the green light is on.
29
Step 5 : Installing Amarino (software part)
Go to http://www.amarino-toolkit.net/ and download the following applications on your mobile phone
a. Amarino – Android Application- to be installed on phone.
b. Amarino Plug-in Bundle- to be installed on phone.
c. Amarino Library- To be kept in Java Project
30
Step 6 : Test the communication between Blue smirf module and
Arduino (laptop part)
Seek the open source at http://www.amarino-toolkit.net/index.php/getting-started.htmlNote: set the Serial Monitor Baud rate to 115200. Code lists in the below:
Step 7 : Set up Eclipse (software part)
It is the most complicated part of this experiment.You can get a detailed tutorial from http://developer.android.com/sdk/eclipse-adt.html#installingThe basic idea is to Install the Eclipse first(follow the system requirements), then install the android SDK, then install ADT plugin for Eclipse IDE.
Step 8 : Create new project in Eclipse (software part)
There is an open source of Sensor Graph, down load from http://code.google.com/p/amarino/downloads/detail?name=SensorGraph_02.zip&can=2&q=Codes still need to be changed to realize the function and is shown in the end of the manual.
31
Step 9 : Set up the application on the phone (software part)
NOTE: you must have ADT-Plugin installed.
Go to http://developer.android.com/sdk/eclipse-adt.html
*make sure you have your “AmarinoLibrary_v0_55.jar ” file is included. Download it
step 10 : Install the application in your phone(software part)
Your phone should already be connected via usb to your computer, In your phone settings , and install from unknown sources checked.In Samsang S1, it was in settings>applications>USB debugging.
Next, find alcohol detecting.apk that imports to your phone.
This will install the Alcohol detection app to your phone and run it.
TIPS: If your application is not installed on phone, then there is a possibility that your phone’s device driver is not installed on computer. Go to Device manager and install the driver for your phone. If you have internet connection, it searches itself for the driver. You can get more information from here:http://developer.android.com/guide/developing/device.html——————————————-
32