Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
of 12
Transcript of Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
1/12
Group Check Point No. Rule No. Group Rule / Crtiteria
T/M 1 2.1.2 General Vehicle Dimentions
1.1 Max width of vehicle with wheels pointing forward direction
1.2 Length of vehicle (front to rear bumper max extenedlength with parts projecting)
T 2 2.1 General Towing Hitch Point
T 2.1 2.10.1 General Front Hitch Point -
M 2.1.1 General Maximum OD
Q 2.1.2 General If, Hitch Plate
T 2.2 2.10.2 General Rear Hitch Plate -
M 2.2.1 General Maximum thickness
M 2.2.2 General Minimum Hole Diameter
M 2.2.3 General Radial clearance maximum from hole
M 2.2.4 General Hole to tube minimum clearance
T/Q 3 3.2 General Unstability of vehicle (handling or other vehicle dynamics)
T/Q 4 3.10.1 General Maximum time for a driver to egress the vehicle
T 5 3.10.6 General Throttle - Type
Q 5.1 General Stopper
Q 5.2 3.10.6.1 General Throttle extension (e.g. blocks of wood etc.)
T 6 3.3.2 Roll Cage Lateral Space
M 6.1 Roll Cage Driver's helmet minimum clearance from top of roll cage
M 6.2 Roll Cage Driver's body parts minimum clearance from car structure envelop
T 7 3.3.3.1 Roll Cage Elements of Roll Cage
T 7.1 Roll Cage Type
T 7.1.1 Roll Cage Primary Members
M 7.1.1.1 Roll Cage Minimum OD
M 7.1.1.2 Roll Cage Minimum Wall Thickness
M 7.1.1.3 Roll Cage Carbon Content
M 7.1.1.4 Roll Cage Yield strength /Bending stiffness
T 7.1.2 Roll Cage Secondary MembersM 7.1.2.1 Roll Cage Minimum OD
M 7.1.2.2 Roll Cage Minimum Wall Thickness
M 7.2 Roll Cage Maximum length of unsupported memebers which are not straight (bend radii < 152 mm/ 6')
T 7.2.1 Roll Cage Maximum angle between two ends of non-straight tubes
BAJA SAEINDIA 2013 SELF-CERTIFICATI
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
2/12
T 14 3.3.3.9 Roll Cage Roll Hoop Bracing (FAB)
Q 14.1 Roll Cage Location
Q 14.2 Roll Cage Type
M 14.3 Roll Cage Maximum length between attachment points if triangulated with straight member.
M 14.4 Roll Cage Minimum angles of triangulation.
M 14.5 Roll Cage Maximum length of tube between attachment points if bent tube is used for bracing.
T 15 3.3.4 Roll Cage RHO/FBM Gusseting
Q 15.1 Roll Cage Type
M 15.2 Roll Cage Minimum Length
M 15.3 Roll Cage Minimum Thickness
Q 15.4 Roll Cage Welding
T 16 3.3.5 Roll Cage Butt Joints
Q 16.1 Roll Cage Type of sleeve
M 16.2 Roll Cage Length of extension to each side of joint
T 17 3.5 Roll cage Driver Head Clearance
M 17.1 Roll cage Minimum clearance from seating surface to bottom of upper roll cage tube
M 17.2 Roll cage Minimum vertical clearance of helmet of team tallest driver to bottom of upper roll cage
T 18 3.6.1 Roll cage Roll Cage Material
Q 18.1 Roll cage Type
M 18.2 Roll cage Bending strength
M 18.3 Roll cage OD (outer diameter)
M 18.4 Roll cage Wall thickness
M 18.5 Roll cage Minimum Carbon Content
T 18.6 Roll cage Steel tube with exceeding bending stiffness & strength compare to above material
M 18.6.1 Roll cage Mimimum wall thickness
T 19 3.9 Roll cage Bolted Roll Cages - Rule
Q 19.1 Roll cage Type of mounting flanges.
M 19.2 Roll cage Minimum thickness of the flange.
M 19.3 Roll cage Minimum diameter of the flange.
M 19.4 Roll cage Minimum flush-gaps between the mating faces of the flanges.
M 19.5 Roll cage Minimum welded length of tab mounts with the tubing.
Q 19.6 Roll cage Area of the tab/ flange through which the bolts pass.
T 20 3.10.1 Roll cage Driver' s seat
Q 20.1 Roll cage Types of seats RECOMMENDED
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
3/12
M 24.3 Safety Maximum distance from helmet
M 24.4 Safety Padded with closed cell foam density
T/Q 25 3.8 Safety All sharp edges which might endanger the driver, crew, or officials, including "the Wraps", must b
T 26 3.10.4 Safety Kill Switch
Q 26.1 Safety Type
Q 26.2 Safety RECOMMENDED options
Q 26.3 Safety NOT ALLOWED
Q 26.4 Safety Working condition
Q 26.5 Safety Mounting
Q 26.6 3.10.4.2 Safety Location
Q 26.6.1 Safety Position - Cockpit
Q 26.6.2 Safety Position - External
T 27 3.10.4.5 Safety Fire extinguisher
Q 27.1 Safety Type
M 27.2 Safety Minimum Capacity
M 27.3 Safety Quantity
Q 27.4 Safety Mounting Position
Q 27.5 Safety Labeled with
Q 27.6 Safety Calibration & Validity
T 28 3.11.1 Safety Driver Restraint System
Q 28.1 Safety Type
Q 28.2 Safety Gap when seat belt is in pulled condition
Q 28.3 Safety Anchoring
Q 28.4 Safety Mounting for all belts.
T/Q 29 3.11.2 Safety Release Mechanism
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
4/12
M 32.5 Safety Min thickness of frame tabs that accept lap belt
M 32.6 Safety Weld length in the tabs mounted to the frame to accept lap belt
M 32.7 Safety Minimum length of material in radial direction from edge of mounting bolt hole to the closest out
T 33 3.14 Safety Arm Restraint
Q 33.1 Safety Location
Q 33.2 Safety Specification
Q 33.3 Safety Type
M 33.4 Safety Expiry
T 34 3.20 Safety Driver's Helmet
Q34.1
Safety Type
Q34.2
Safety Specifications
T 35 Safety GogglesType
T 36 Safety Neck support
Q 36.1Safety Type
Q 36.2 Safety Rating
M 36.3 Safety Expiry
T 37 Safety Driver Clothing
Q 37.1Safety Type of clothing
Q 37.2 Safety Rating
M 37.3 Safety Expiry
T 38 Guards Guards
Q 38.1 3.19 Guards Parts to be shielded
Q 38.2 Guards Type of material
T 38.3 3.19.1.1 Guards Intent
T 39 2.3.11 Engine Exhaust system
Q 39.1 Engine Exhaust system and muffler condition
M 39.2 Engine Exhaust System Location with minimum distance between its extremities and vehicle perimeter
T 40 2.3.14 Engine Engine Governor
M 40.1 Engine Governor Spring Setting
T 41 2.3.15 Engine Hybrid electric power system
T 42 2.5 Engine Battery requirements
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
5/12
Q 49.1 Fuel system Type
Q 49.2 Fuel system Cap and gasket durability
T 50 3.15.1 Braking Braking
Q 50.1 Braking Type
Q 50.2 Braking Minimum vehicle speed
Q 50.3 Braking Brake circuits
Q 50.4 Braking Bleed point location
Q 50.5 Braking Brakes on driven axle
Q 50.6 Braking Brake Lines
Q 50.7 Braking Hand Brake
T 51 3.15.2 Braking Brake light
Q 51.1 Braking Color
Q 51.2 Braking Rating
M 51.3 Braking Minimum distance from ground
M 51.4 Braking Minimum distance for shining parallel to ground and not at an angle.
Note for Group -
T - Title /Sub Title in Group
M - Measurement Parameters
Q - Quality paramneters
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
6/12
Actual Remark
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
7/12
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
8/12
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
9/12
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
10/12
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
11/12
M/Q/T Rule No. Group Check Point No. Rule
T 2.11 General 1 Vehicle Identification
Q General 1.1 Vehicle Number Display
T General 1.1.1 TOP of VehicleQ General 1.1.1.1 Type
Q General 1.1.1.2 Numeral Type
M General 1.1.1.3 Numeral Height
M General 1.1.1.4 Minimum Line Width
Q General 1.1.1.5 Shape
Q General 1.1.1.6 Location
T General 1.1.2 BODY of Vehicle
Q General 1.1.2.1 Painted on numbers and stencils/decals mounted flush to a body panel
Q General 1.1.2.2 Numeral Type
M General 1.1.2.3 Numeral HeightM General 1.1.2.4 Minimum Line Width
Q General 1.1.2.5 Colour
Q General 1.1.2.6 Location
T 2.11.2 General 1.1.3 College Name
Q General 1.1.3.1 Type
M General 1.1.3.2 Height
M General 1.1.3.3 Width
T 2.12.2 General 2 Transponder Mounting
Q General 2.1 Orientation
M General 2.1.1 Location
Q General 2.1.2 Other details
T 3.10.2 General 3 Body Panel - Type
Q General 3.1 Material
Q General 3.2 Protection
T/Q 3.10.3 General 4 Belly Pan -Type
M General 4.1 Max portion of links exposed inside cockpit (w/o shielding)
T 3.8 Roll cage 5 Roll cage padding
Q Roll cage 5.1 Type
BAJA SAEINDIA 2013 SELF-CERTIFICATION
-
7/28/2019 Self Certi-Checksheet SCCs_BAJA SAEINDIA 2013_30th Dec 2012
12/12
Actual Remark
