SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in...

144
Handbook SelectionProfessional

Transcript of SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in...

Page 1: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook

SelectionProfessional

Page 2: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Legal notice

We reserve all copyrights for this handbook. This handbook or any parts thereof cannot be printed in any form without our written permission. No liabilities will be assumed for any damages caused by SelectionProfessional or programs or files contained within. All rights are protected. Any form of duplication, in whole or in part, is prohibited.

Hettich FurnTech GmbH & Co. KG

Gerhard-Lücking-Straße 10

D 32602 Vlotho

www.hettich.com

October 2012, Printed in Germany

Page 3: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 3 / 144

Contents

1. Introduction ....................................... ......................................................................7

1.1 Basic principles...................................................................................................7

1.2 System requirements ..........................................................................................7

1.3 Innovations in SelectionProfessional 2.1 ............................................................8

1.4 Help / Infoline......................................................................................................8

1.5 Installation / Activation ........................................................................................9

2. First steps ........................................ ......................................................................10

2.1 Starting SelectionProfessional ..........................................................................10

2.2 Program components........................................................................................10

2.3 Example design ................................................................................................11 2.3.1 Starting and selecting a design...................................................................11 2.3.2 Carcase division .........................................................................................12 2.3.3 Article list / Catalogue selection..................................................................16 2.3.4 AutoCAD display ........................................................................................19

3. Designer - Functional description .................. .....................................................21

3.1 Screen layout ....................................................................................................21

3.2 Screen layout cabinet partitioning.....................................................................24

3.3 Screen layout item lists .....................................................................................25

3.4 Screen layout completed design .......................................................................26

3.5 Zone and components ......................................................................................28 3.5.1 Example of how to select zones .................................................................28 3.5.2 Changing, deleting, hiding parts .................................................................31

3.6 Front and component divisioning ......................................................................33

3.7 Item lists and favorites lists ...............................................................................37 3.7.1 Item list .......................................................................................................37 3.7.2 The favorite list ...........................................................................................39

3.8 Export ...............................................................................................................39 3.8.1 Bill of items – wood.....................................................................................40 3.8.2 Hettich order list..........................................................................................40 3.8.3 Document Manager ....................................................................................41 3.8.4 Hesse order list...........................................................................................41

3.9 Loading, saving, cabinet library.........................................................................41

3.10 Hesse Module ...................................................................................................42

3.11 Functions in the standard cabinet, sliding and folding, special designs sections43 3.11.1 “Insert centre panels" function ....................................................................43 3.11.2 “Insert construction shelves" function .........................................................44

Page 4: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

4 / 144 SelectionProf_Handbook_EN.pdf

3.11.3 “Insert shelves" function”.............................................................................45 3.11.4 “Insert drawers" function“ ............................................................................45 3.11.5 “Insert internal drawers" function ................................................................49 3.11.6 “Insert doors" function.................................................................................51 3.11.7 „Flaps“ function ...........................................................................................53 3.11.8 “Select/change knobs/handles" function .....................................................54 3.11.9 „Locking systems” function .........................................................................55 3.11.10 “Insert cabinet accessories" function” .........................................................59 3.11.11 “Insert front divider” and “Insert zone divider" function................................59

3.12 Functions in the office cabinet section ..............................................................60 3.12.1 “Insert construction shelf" function ..............................................................60 3.12.2 “Insert shelves" function”.............................................................................60 3.12.3 “Insert drawers" function“ ............................................................................61 3.12.4 “Insert internal drawer" function ..................................................................62 3.12.5 “Insert drawers with lock" function ..............................................................62

3.13 Functions in the Office-Container section .........................................................63 3.13.1 “Insert drawers" function .............................................................................63 3.13.2 “Insert drawers with lock" function ..............................................................65

3.14 Sliding and Folding Constructions in SelectionProfessional..............................65 3.14.1 Differentiation of application area ...............................................................65 3.14.2 Selection of Fittings in SelectionProfessional .............................................67 3.14.3 Fitting: TopLine 22 standard doors .............................................................68 3.14.4 TopLine 25/27.............................................................................................69 3.14.5 Fitting: TopLine 1 ........................................................................................70 3.14.6 Fitting: WingLine 770/780 ...........................................................................71 3.14.7 Fitting: WingLine 77 ....................................................................................72 3.14.8 Fitting: Wing 77...........................................................................................73 3.14.9 Integrated Sliding and Folding Door Constructions.....................................74 3.14.10 SlideLine 55 / 56 .........................................................................................75 3.14.11 TopLine 110................................................................................................76 3.14.12 WingLine 170..............................................................................................77 3.14.13 WingLine 26................................................................................................78

3.15 Placing Handles on Sliding and Folding Doors .................................................79 3.15.1 Placement Choices.....................................................................................79 3.15.2 Placement of Handles................................................................................79

3.16 Kitchen Constructions .......................................................................................80 3.16.1 Construction types ......................................................................................80 3.16.2 Full circle carousel fitting.............................................................................80 3.16.3 Segmented carousel fitting .........................................................................82 3.16.4 Three quarter carousel fitting ......................................................................82 3.16.5 Corner cabinet Revo 45 ..............................................................................84 3.16.6 Corner cabinet Revo 90 ..............................................................................87

Page 5: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 5 / 144

3.16.7 Semi circle carousel fitting ..........................................................................88

4. Selection CAD (AutoCAD) Principles ................. .................................................90

4.1 Introduction to CAD...........................................................................................90

4.2 AutoCAD surface ..............................................................................................90 4.2.1 Menu functions ...........................................................................................90 4.2.2 AutoCAD icon functions..............................................................................92

4.3 Create job .........................................................................................................93 4.3.1 Comparison of the individual save functions in SelectionProfessional .......94 4.3.2 Create job/project .......................................................................................95 4.3.3 Load job / project ........................................................................................96 4.3.4 Save job / project........................................................................................96

4.4 Measuring .........................................................................................................97 4.4.1 Dimension part ...........................................................................................97 4.4.2 View dimensioning......................................................................................98 4.4.3 Cabinet views .............................................................................................99

4.5 Printing/plotting ...............................................................................................100

5. Document manager................................... ..........................................................105

5.1 Basics .............................................................................................................105

5.2 Start Document Manager................................................................................105

5.3 Start Document Manager now ........................................................................106

5.4 Create new template.......................................................................................106 5.4.1 Sizing views..............................................................................................107 5.4.2 Layout.......................................................................................................107 5.4.3 Page format ..............................................................................................108 5.4.4 Export .......................................................................................................108

5.5 Modify template...............................................................................................108

5.6 Delete existing template..................................................................................109

5.7 Wood – Bill of Materials ..................................................................................109

5.8 Hettich Order list .............................................................................................109

6. Roomplan functions................................. ...........................................................110

6.1 Introduction .....................................................................................................110

6.2 Starting Roomplan ..........................................................................................110

6.3 Define wall ......................................................................................................111

6.4 Define windows / doors and openings ............................................................114

6.5 Modifying windows / doors / openings ............................................................115

6.6 Deleting windows / doors / openings...............................................................115

6.7 Change the wall characteristics ......................................................................116

6.8 Insert furniture or accessories.........................................................................117

Page 6: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

6 / 144 SelectionProf_Handbook_EN.pdf

6.8.1 Select cabinet ...........................................................................................117 6.8.2 Add furniture to a wall ...............................................................................117 6.8.3 Inserting furniture in an existing object (furniture or decorative object) .....118

6.9 Delete item......................................................................................................121

6.10 Move / rotate item ...........................................................................................121

6.11 Select and insert decorative elements ............................................................121

Example: Inserting a sink unit...................................................................................122

6.12 Definition of raster ...........................................................................................124

6.13 Roof pitch definition.........................................................................................127 6.13.1 Insert roof elements ..................................................................................127 6.13.2 Alignment of walls to the roof....................................................................128 6.13.3 Blending roof elements .............................................................................129

6.14 Component functions ......................................................................................129 6.14.1 Work top functions ....................................................................................129 6.14.2 Plinth functions .........................................................................................133 6.14.3 Cornice functions ......................................................................................134 6.14.4 Front panel functions ................................................................................136 6.14.5 Visible sides functions...............................................................................137

6.15 Material ...........................................................................................................139 6.15.1 Material selectionl .....................................................................................139 6.15.2 Color display of room / cabinet .................................................................141 6.15.3 Concealed display / Light symbols............................................................142

6.16 Output .............................................................................................................143 6.16.1 Wood- Bill of Materials ..............................................................................143 6.16.2 Hettich order list ........................................................................................143 6.16.3 Document manager ..................................................................................143

6.17 Examples ........................................................................................................144

Page 7: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 7 / 144

1. Introduction

1.1 Basic principles

Planning, presenting, producing with SelectionProfessional.

Planning furniture quickly and accurately, presenting plans to the client and making out orders are nowadays all part of the daily routine for cabinet-makers and interior fitters. SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful sales talks, customer presentations and furniture production.

SelectionProfessional is a joint development by Hettich FurnTech GmbH & Co. KG and imos AG. This high-performance, computer-aided furniture design package has been created on the basis of the familiar AutoCAD system from Autodesk.

1.2 System requirements

PC Intel® Pentium® 4

AMD® Athlon = 2,2 GHz (3,0 GHz Windows® VISTA / 7)

Intel® / AMD® Dual Core = 1,6 GHz (2,0 GHz Windows® VISTA / 7)

Windows®

operating system

Windows® XP (SP 3) / VISTA / Windows® 7 (32/64bit)

Computer data storage

Windows XP: 1 GB RAM

Windows® VISTA & 7: 2 GB RAM

Graphics card 128 MB (True Color), OpenGL®- capable, Direct3D®- capable

Screen resolution 1024 x 786

Hard disk capacity 4 GB (for custom setup)

5,5 GB (for complete setup)

Drive DVD-ROM

Internet browser Microsoft Internet Explorer® 6 (or higher), Mozilla Firefox

Adobe Reader® 6.0 or higher

Page 8: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

8 / 144 SelectionProf_Handbook_EN.pdf

1.3 Innovations in SelectionProfessional 2.1

In this update, special attention has been given to the compatibility of 64-bit systems and the integration of the new products.

Installation Fully compatible with 32 and 64-bit systems

Catalogue - Current product contents, e.g the platform concepts of the ArciTech and InnoTech drawer systems, also the TopLine M and TopLine L sliding door systems

Designer - New cabinet library: with ArciTech and InnoTech drawer systems

1.4 Help / Infoline

SelectionProfessional provides you with an extensive help system:

1. Manual

In addition to the main handbook, further handbooks on special topics are also available.

SelectionProf_Installation_EN.PDF

SelectionProf_Catalogue_EN.PDF

SelectionProf_Training exercises_EN.PDF

SelectionProf_Library_EN.PDF

The handbooks are present in the Selection/info/help/eng folder.

You can also get started from the Assistant construction details of the designer or

through with the symbol Help.

2. On-line help in the program

You can select to get help on any particular part of the program you happen to be working in. The Assistants provide additional information as well as a "Help" link. You will also find further information in the program menu under "Help".

3. Internet Log on to www.selection-professional.com for all the latest information, news, tips & tricks and fast answers to FAQs about SelectionProfessional.

Page 9: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 9 / 144

In addition, you will be informed about the latest updates. The manuals and further PDF documentation are constantly updated here as well. This is where you will also find the links for downloading the Internet Explorer or Adobe Acrobat programs you will need.

4. Info line Hettich also operates an info line to provide help with any unanswered questions you may have.

Tel.: +44 (0)160 - 872 95 52

Fax: +44 (0)161 - 848 76 05

E-mail: [email protected]

Internet: www.selection-professional.com

1.5 Installation / Activation

The program should be activated after installation. Activation should be carried out within 90 days. After that the designer component can no longer be used. However the registration can be implemented after 90 days. A detailed introduction for installation and activation is available in the help document “SelectionProf_Installation_EN.PDF “.

Page 10: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

10 / 144 SelectionProf_Handbook_EN.pdf

2. First steps

2.1 Starting SelectionProfessional

The programm can be started from the desktop icon or by selecting Start/Programmes/Selection/SelectionProfessional. The SelectionProfessional portal opens once the program has been started. SelectionProfessional is divided into several parts:

1) Start design component Designer & Hettich catalogue

2) Start design component Designer

3) Start Hettich catalogue

2.2 Program components

1) Start design component Designer & Hettich catalogue With this option, the designer, the CAD component and the catalogue in background would be started. This is immediately available by accessing favourites in the catalogue and does not need to be started anymore.

2) Start design component Designer Here only the Designer + CAD component would be started. If the catalogue is required only for a favourite query then it can be started later. The advantage lies in the quick start and lesser consumption of the required system resources.

3) Start Hettich catalogue Here only the Hettich catalogue would be started.

Please do not close any of these points while working with the program.

Page 11: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 11 / 144

2.3 Example design

2.3.1 Starting and selecting a design

Once you have started the Designer from the start portal, you will see "Design Assistant". The "New construction" option takes us to the construction selection window. The basic types of the furniture you are going to design are shown in the construction selection window. Selecting a "+" sign opens an option, "-" closes it again.

For the example design, let us select a "Standard cabinet / Single cabinet / Overlay". The relevant dialog is opened at the bottom right by selecting "Carcase size".

Page 12: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

12 / 144 SelectionProf_Handbook_EN.pdf

Change the height to 820 (figures are always in mm, the unit of measure does not need to be entered), width to 900.

Entered values do not have to be saved or confirmed by pressing Enter. You can switch between the different input fields using the mouse.

Now select the "Bottom shelf" and enter the "120" in the "Height offset" field. This raises the base by 120mm, with the sides continuing through to the floor.

The forward button takes you to the carcase division window.

2.3.2 Carcase division

The cabinet is displayed from the front and from the side. The Assistant shows all parts that can be incorporated into the cabinet.

Page 13: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 13 / 144

Insert centre panel

For the example design, let us use the "Insert centre panel" function to add the centre panel. A new dialogue window opens at the bottom right.

The position of the centre panel is defined in the "Division" field. The position is set to 600mm from the left by entering "600mm:1". The 600mm relate to the clear internal width. The mm must always be included for divisioning. Division is the only field that demands the "mm" unit of measure. The "1" represents a ratio and indicates the remaining available space. Details on using the division function are also provided in the section headed "Front and component divisioning".

The green ticks are used for confirming the entries you make and for inserting the centre panel.

Setting zones

As the next step, we are going to add a shelf. A so-called "Zone" must be activated so that the system knows which side to fit the shelf on. This is done by clicking the mouse inside the appropriate section of the cabinet. As we are going to put a shelf in the left-hand section / zone, this is the zone you must click the mouse in. It is highlighted in green.

Details on the subject of zones and parts are provided in the section headed "Zones and parts".

Page 14: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

14 / 144 SelectionProf_Handbook_EN.pdf

Inserting shelves

Select the "Insert shelf" function from the Assistant. A new dialog window now opens at the bottom right. We are now going to space three shelves apart at equal distances throughout the zone. To do this, enter or select the number "3" from the menu. This corresponds to a spacing of "1:1:1:1".

As before, the entry is confirmed with the green tick.

Inserting doors

As the next step, we are going to add the doors. To do this, you must once again activate the left-hand zone with the mouse so that it is displayed in green. Select "Insert doors" from the Assistant. The dialogue window opens. Select "Standard door" as the door type. Select the "+" sign to obtain further details on this door type. Two further options are opened: "Division" and "Hinge". In "Division", select "Double door" from the "Construction type" field. Options can be selected by clicking the arrow to the right of the field. Finally, confirm your entries with the green tick.

Inserting drawers

Now click on the right-hand zone, which is still blank, to activate it. This zone is then displayed in green. From the Assistant, select "Insert drawers".

The relevant dialogue opens. You can choose from a variety of drawer types. In our example, we are going to select a "Wood-box with internal drawer". This drawer is to be mounted on a "Quadro runner". This option must, therefore, be selected too. Use the "+" sign to select the "Division" option. Select three for "Number". The fronts are distributed evenly throughout the height. Entries are confirmed with the green tick.

Page 15: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 15 / 144

Inserting handles

To insert handles, you must switch from zone mode (green) to the component mode (red). This is done using the zone/component mode symbol.

After changing modes, the small front view turns from green to red.

Using the mouse, select the door fronts which are then displayed in red. Now select the "Select knobs/handles“ function from the Assistant. A new dialogue opens. The entire ProDecor product range is stored in the program. In order to make a selection in advance at this stage, let us choose a "Drilling distance" of "128" and "Stainless steel" as the "Material". Define the "Insertion point" as "Top opposite hinge". As before, confirm all entries with the green tick.

Using the mouse, now select the drawer front. This also turns red. Once again, select the "Select knobs/handles" option. The dialogue opens. The drilling distance and the materials can be accepted.

Set the "Insertion point" to "Centered". These entries, too, must be confirmed with the green tick.

The finished cabinet is displayed from the front and side.

This completes the cabinet design process. Use the "forward button" to quit the carcase divisioning section.

Page 16: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

16 / 144 SelectionProf_Handbook_EN.pdf

2.3.3 Article list / Catalogue selection

The top right-hand section of the next window displays all of the fitting groups required for the carcase in the "Article list" (1).

There are two ways of assigning exact fittings to these fitting groups:

1) Selecting from Favourites

2) Selecting from the Hettich catalogue

In order to select a fitting from the favorites, a fittings group is initially typed into the item list (2). Thereafter, the probable favorites-sets for this selection appear towards the bottom right in the “list of favorites” (3). A favorites-set consists of a favorites-header and one or more Hettich fittings. For e.g., for the concealed hinges fittings group, the Intermat 9943 TH FIX hinge is offered with a suitable mounting plate. By typing the favorites into the selection below the corresponding fittings set is assigned above the fittings group (4).

If you wish to select a fitting from the full-length Hettich catalogue, select the "Use catalogue selection" option instead of the Favourite (5). The relevant fitting group is then selected from the catalogue.

Page 17: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 17 / 144

For example, the following selection is carried out:

Pos. 1 Cup hinge > Favourite > Intermat 9943 TH Fix

Pos. 2 Cup hinge > Favourite > Intermat 9943 TH Fix

Pos. 3 Knobs and handles > Use catalogue

Pos. 8 Quadro runner > Favourite > Quadro V6/550

Pos. 11 Adjustable shelf > Favourite > Compartment shelf support for wooden shelves

To position the fittings group “handles and knobs“on “Use catalogue selection“, the entry should be initially selected with the help of the mouse in the item list. Subsequently the entry “Use catalogue selection“ is selected in favorites.

The catalgue start is executed with the green check mark . The program opens the electronic Hettich catalogue and searches for suitable products under the “handles and knobs“fittings group.

The catalogue now displays all handles that match the previously defined properties (material + drilling distance).

Page 18: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

18 / 144 SelectionProf_Handbook_EN.pdf

Three symbols appear in front of the list:

Select accessories

Transfer to CAD

Detailed information

Select accessories

The accessories that are available for the main article are selected by clicking the accessories symbol. A list of accessories shows all possible accessory types. If an accessory is an article that is essential for the design, a red exclamation mark is set in front of the relevant group. If you don't select an essential accessory article, the program automatically prompts you to do so.

Transfer to CAD

If you wish to select an article from the product list for the design, select the CAD symbol. Add the relevant article to the article list.

Detailed information

If you require additional information on the product, click the "Detailed information" button to retrieve further details. From the detailed overview, you can also display the accessory or transfer the article to the Designer.

In our example, we are going to select any random handle and click the Designer

transfer button.

The program automatically adds the handle to the article selection list. For the next item of furniture you design, there is no need to select the handle again but retrieve it directly from Favourites.

The article list changes its colour from black to green. This completes the article selection process. The item selection is thus complete and the entry of the item list is fixed. If the selection for this entry is changed, it has to be selected in the item list using the right mouse click. At the end it can again be released using “change”. One can leave the item selection using the forward arrow.

Page 19: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 19 / 144

The finished cabinet is displayed in 3D. You can now carry out a number of actions on the cabinet.

2.3.4 AutoCAD display

The CAD / Roomplan function in the Assistant allows you to switch to the AutoCAD module. The cabinet is displayed in a wire grid 3D perspective. Component dimensioning is the most important function in the AutoCAD section of the program. Let us dimension the left outer side of the carcase automatically. To do this, change to the

top view using the symbol.

This is opened by clicking the "Dimension part" symbol (left). The cursor changes into a rectangle. Using the rectangular cursor, now select the outer side. It is important to select precisely the line that represents the outer side.

The component is automatically displayed with dimensions. It can be printed out or saved in the 2D view.

Page 20: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

20 / 144 SelectionProf_Handbook_EN.pdf

The "Dimension part" symbol enables you to perform further dimensioning. Quit the dimensioning mode by clicking the "Reverse dimensioning" symbol (right).

Click the "Switch to Designer“ button in the Assistant to quit the AutoCAD part of the program and return to the Designer in the 3D view. Nothing needs to be saved in the AutoCAD part as this is all controlled through the Designer part.

Page 21: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 21 / 144

3. Designer - Functional description

3.1 Screen layout

The Designer screen is divided into several sections that are repeated at all design stages.

1) Progress bar

The Designer is divided into 4 sections that run through in succession.

Selecting a construction

Carcase division

Article list / Catalogue selection

3D display

Page 22: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

22 / 144 SelectionProf_Handbook_EN.pdf

The section activated is shown by a red line below the relevant image.

2) Assistant

The Assistants guide you through the program and display the range of functions that are available. They also provide helpful tips on the application concerned. You can get additional information by selecting "Help".

Upload standard settings

Uploads standard Designer settings. Modified values are reset to original values again.

Open

Opens an existing design. You are given the possibility of saving the active design.

CAD/Roomplan

This option is used for opening the AutoCAD part of the program. This must be done, for example, to dimension the design or to start Roomplan.

All details of the AutoCAD functions are explained later on in the manual.

End Designer

Closes the Designer as well as the AutoCAD and AutoCAD Renderer parts of the program. Alternatively, you can also close the program by selecting the "File/Exit" menu options. The program should always be closed from the Designer and not from other parts, such as the AutoCAD part.

Help

Retrieves help on the Assistant. The handbooks can be started from the overview.

3) Section change

The forward button can be used to change from one segment to the next. Use the backward button to return to the previous view. This enables to move backwards and forwards at any time and is particularly useful, for instance, if you wish to make an alteration.

4) File informations

Profile: Shows the current profile name.

Name: Name of the cabinet if saved.

Page 23: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 23 / 144

5) Menu bar

File

New: Creates a new design.

Open: Opens a cabinet that has already been designed.

Save: Saves a cabinet currently being designed. This function is only available once you reach the Carcase division part.

Delete: This is where you can delete saved cabinets.

Import: This can be used to make cabinets available to other SelectionProfessional users or save a cabinet to an external data medium (floppy disk, memory stick etc.).

Export: Reads cabinet designs in from other SelectionProfessional users or loads cabinet designs from an external data medium.

End: Exits the Designer and Selection CAD.

Profile

For some furniture designs it is often necessary to select specific settings. For kitchen base units, for example, it is generally possible to select 16 panel thicknesses, or always use grooved rear panels. All settings (e.g. cabinet height, width, base panel thickness, backset dimensions etc.) that are capable of being altered in the construction selection window can be saved under custom profiles.

Load: Loads an existing profile

Save: Saves a profile. All changes made in the construction selection window, from the standard cabinet to custom designs, are saved.

Delete: Deletes an existing profile

Help

Retrieves help on the Assistant currently being used.

Page 24: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

24 / 144 SelectionProf_Handbook_EN.pdf

3.2 Screen layout cabinet partitioning

1) Preview image

The preview image displays the cabinet in 2D in front and lateral view.

2) Action buttons

Front view

Top view

Changes to 3D mode

Changes to component mode

Changes to zonal mode

3) Assistant

Different components and fittings for the cabinet partitioning can be selected from the Assistant.

Page 25: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 25 / 144

3.3 Screen layout item lists

The designs of the suitable fittings are allocated in the item lists. They may be selected from the Hettich catalogue or from favorites.

Page 26: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

26 / 144 SelectionProf_Handbook_EN.pdf

3.4 Screen layout completed design

1) Window functions

The completed cabinet design is displayed in the window. In addition, different mouse functions are available.

Left mouse button Turns cabinet

To do this, keep the left mouse button pressed and turn the mouse in the chosen direction.

Right mouse button Magnifies / reduces the cabinet image

Keep right mouse button pressed and move mouse away from you or towards you. Moving away from you reduces the image, moving towards you magnifies it.

Left + right mouse button Shifts cabinet

Keep right+left mouse button pressed simultaneously shift in the chosen direction.

Page 27: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 27 / 144

The functions of the mouse can also be permanently assigned to the left mouse button. To do this, select one of the three symbols.

Left mouse button to reduce / magnify cabinet image

Left mouse button to turn cabinet

Left mouse button to shift cabinet

To cancel the function, all you have to do is re-select it. Now it is deactivated again.

2) Action buttons

Front view

Side view

Top view

Set standard (useful if everything has been adjusted)

Concealed cabinet display

Semi-transparent cabinet display

Wire grid model

3) Assistant

New construction

Starts a new design. There are two ways of saving the active design.

Save

Saves the active design. You can select an existing directory or create a new one.

Page 28: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

28 / 144 SelectionProf_Handbook_EN.pdf

Change functions

Alterations can be made to the cabinet designed in SelectionProfessional. This is done using the following functions:

- Change dimensions (e.g. height, panel thickness etc.)

- Change divisioning (e.g. add shelves, change doors etc.)

- Change fittings (e.g. change handle selected, select another hinge type etc.).

You can find details on the different ways of making alterations in the section headed "Altering designs".

Hesse Module

The cabinet can be displayed in different surfaces with the help of the Hesse Module.

In addition, it is possible to switch to display options with the help of the “Output“ tab.

3.5 Zone and components

3.5.1 Example of how to select zones

Selecting zones and components is an important function within the carcase divisioning section. The cabinet displayed below is to be divided into different sections.

So far, the cabinet has had three evenly spaced centre panels. We are now going to add a construction shelf to all four resultant zones.

Page 29: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 29 / 144

If you wish to activate several zones, they must be selected in succession. If you have selected the wrong zone, it can be deactivated by selecting it a second time.

If several zones were addressed and only one needs to be activated, a double click in the desired zone will deactivate all the other zones again.

If the other zones require to be activated, a right mouse click on the point “Activat all zones” in the menu will activate all cabinet domains simultaneously.

You can insert a construction shelf once all zones have been activated (green). The data for the construction shelf now applies equally to all four zones. The construction shelf will be inserted in all four zones.

Inserting the construction shelves has formed new zones. The cabinet now has a total of eight zones. Four drawers are now going to be inserted in the top zones. As we want all of the drawers to be the same, they can all be highlighted in one go. The drawers are then selected from the menu and automatically inserted in the zones. It is important to remember that drawers can only be inserted simultaneously if the zones are identical in size.

Page 30: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

30 / 144 SelectionProf_Handbook_EN.pdf

Loose shelves are now going to be added across all four bottom zones. To do this, you must once again activate all four zones and select the shelves from the Assistant. Unlike construction shelves, loose shelves do not form zones.

Now we are going to insert doors in the right and left-hand zone. As this requires the use of a left-hinged and a right-hinged door, they must be selected separately.

Highlight the zones individually and insert the appropriate door in each. Let us now insert a double door in the middle. To do this, both zones can be selected simultaneously. After selecting the door function, a double door will be inserted automatically. If you activate several zones, the program automatically tries to insert one door across all zones. If, added together, the zones are wider than 600 mm, a double door will be inserted automatically.

Page 31: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 31 / 144

The cabinet is now equipped with all elements. This is the point at which to select the handles for the fronts. To do this, you must click the "Zone mode/Component mode"

to switch to the component mode (red). First, select all drawer fronts so that all four are displayed in red. Using the "Select/change knobs/handles" function, assign a handle to all drawers.

Now highlighted in red, all drawers are fitted with the handles. In the "Insertion point – Top opposite hinge" handle setting, the program automatically places the handles in the correct position.

3.5.2 Changing, deleting, hiding parts

Any mistake that is made while configuring the cabinet can be corrected at a later stage. You can also subsequently change any part already inserted.

Example of how to change handles

In our example, we want to relocate the handles from a centred position to the upper mid-point. To do this, switch to the component mode (red) and select all drawer fronts. Now press the right mouse button and select the "Change knob/handle" option. The handle dialogue opens, allowing you to re-position the insertion point. You could, of course, also have changed other options.

Example of how to change the side on which a door is hinged

The right-hand door is to be hinged on the left side. To do this, select the door in the component mode and press the right mouse button. From the dialog, select the "Change part" option. The door dialogue opens, allowing you to change the design to "Hinge left".

Page 32: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

32 / 144 SelectionProf_Handbook_EN.pdf

Example of how to delete a shelf

To delete a component, it must be selected in the component mode. However, you cannot select the shelf directly because the door is in front of it. By pressing the right mouse button, select the "Show front panel" option. After removing the tick, the fronts will be hidden. They are not deleted, but merely no longer visible. Now, in the component mode, you can select the shelf you want to delete. Remember here that if several shelves were inserted together, they will also be deleted together. This is always the case for elements that are inserted simultaneously.

Summary

The zone selection function (green) is used for selecting cabinet sections for equipping with doors, drawers, shelves etc.

Component selection function (red) is used for changing or deleting components already inserted. It is also required for selecting handles.

In the component mode, the right mouse button can be used to perform different functions:

Activate zones Changes over to zone selection. Performs the same action as the zone/component selection button

Delete part Deletes the component selected with the mouse

Change part Opens the dialogue for changing the component concerned

Change knob/handle

Opens the knob/handle dialogue for making the relevant changes

Activate all components

Activates all components in the cabinet

Activate all fronts Activates all fronts on the cabinet

Deactivate all components

Deactivates all previously activated components in the cabinet

Show front panel No fronts are shown once the tick is removed.

Page 33: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 33 / 144

The right mouse button is equipped with other functions in the zone mode:

Activate component selection

Switch to component selection. Analogous to the Zones/Components button.

Activate all zones Activates all cabinet domains.

Deactivate all zones

Deactivates all the activated cabinet domains

3.6 Front and component divisioning

A carcase needs to be divided into sections or ratios in many different parts. The drawer front, for example, must be divided up into different height ratios. Centre panels must be spaced apart by internal widths. The hole lines are arranged in relation to depth and height. Cup drillings are positioned in the front.

Selection provides one single function for all of these operations: Division. This is used for performing all the necessary functions.

Divisioning works with exact dimensions or ratios. These two options can also be combined.

"1:1:1" is a division that splits a section into two equal parts.

"200mm:200mm:100mm" divides a 500mm section into parts at the distances specified.

„200mm:1:1“ divides a part in the lower or left section at exactly 200mm, the remainder into two equal halves.

With this, partitions are always undertaken from left to right (e.g. centre panels), bottom to top (e.g. drawers) or from front to rear (e.g. hole lines).

Below, you will find a number of divisioning examples. They may also be applied to divisioning in other application areas.

Page 34: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

34 / 144 SelectionProf_Handbook_EN.pdf

Hole-line division

A division can be used to position the hole line in terms of depth.

Default setting: 37mm:1:37mm

The first hole line now starts at 37mm from the front edge of the cabinet side, the second hole line starts at 37mm from the interior of the rear panel.

The inclusion of ":1:" shows that the depth of the cabinet is unimportant. Even if the cabinet depth were to change, the dimensions of 37mm from the front and 37mm from the back stay as they are. The ":1:" may be regarded as a variable placeholder.

If you wish to insert a third hole line exactly mid-way between the other two hole lines, enter the following division:

"37mm:1:1:37mm"

Each „:“ is present for a hole line.

Top panel / connector divisioning

Connectors can be set for the top and bottom panel.

The standard setting for "Connector division" is "37mm:1:37mm". This shows that the connection is located exactly on the hole line. By changing the divisioning, you can, for example, insert additional connectors.

Centre panel divisioning

Through the "Division", a centre panel divides a selected carcase zone from left to right.

A 1:1:1:1 divisioning inserts three centre panels. The internal widths between individual panels are identical.

Page 35: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 35 / 144

A 300mm:1:1:300mm divisioning inserts three centre panels. The first and last zone have got a clear width of 300mm. Both inner zones are automatically divided equally.

Construction shelf divisioning

Construction shelves are divided from bottom to top. Once inserted, they form new zones. The reference point for a construction shelf is therefore the bottom shelf or a construction shelf that has already been inserted. For the construction panels the inside height is defined between the bottom panels.

A 300mm:200mm:1 divisioning inserts two construction shelves. The inside distance of the bottom construction panel to bottom panel is 300mm and the inside distance between the bottom construction panel and the top construction panel is 200mm. The inside distance between the top construction panel and the top panel is calculated from the remainder.

Page 36: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

36 / 144 SelectionProf_Handbook_EN.pdf

Drawer divisioning

Drawers are divided from bottom to top. Divisioning relates to the dimensions of the front.

1:1:1

2:1:1

300mm:200mm:1

Page 37: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 37 / 144

3.7 Item lists and favorites lists

After the definition and partitioning of the cabinet is complete, the fittings should be allocated. This is carried out in the item list/favorites list section.

In this section the preassembled cabinet is examined on the basis of the available fittings group. Subsequently the potential fittings can be allocated through the favorites list or the catalogue selection of the corresponding fittings group.

It is sub divided into item list (1), favorites list (2) and front view of the cabinet (3).

3.7.1 Item list

All fittings group available in the cabinet are present in the item list (1). In the sample cabinet three complete drawers are fitted with one handle each. This leads to the formation of 3 fittings groups, one group “Handles and knobs“and 2 groups “Three sided drawer system”.

If fittings groups can be merged together, based on their similarity, then they are grouped, e.g. the fittings group „Handles and knobs“. For preassembled drawers the top drawer is considerably lower than the remaining two, which is why only the two lower drawers are grouped. The top drawer receives its individual fittings group. In contrast to both the lower drawers, no front pullouts can be fitted into the top drawer.

To switch off the grouping the right mouse button is clicked anywhere in the item list. The menu which is opened as a result displays the entry “group positioning” with a check mark, which means that the grouping is active. The grouping is switched off by clicking on the entry and all fittings groups in the item list are shown individually. To reactivate the grouping, the entry “group positioning” is clicked again. By switching off the grouping, different fittings can be allocated to the individual fittings groups.

Page 38: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

38 / 144 SelectionProf_Handbook_EN.pdf

If a fittings group is clicked on in the item list, the corresponding components in the front view of the cabinet (3) are highlighted in red and the first favorites set is automatically selected. To assign the desired fitting from catalogue selection the coreesponding fittings group should be placed on “Use catalogue selection”. Subsequently the

catalogue selection can be started with the green check mark .

In order to operate the catalogue selection it is necessary to start the Hettich catalogue. If only the design component Designer is started without the Hettich catalogue, the following message would be displayed.

This question must be confirmed with a “yes”, so that the Hettich catalogue gets started. If the field “Do not display this dialog again” is activated, then this dialogue will not appear in future and the catalogue will start immediately.

After the catalogue browser is started, the following dialog would be displayed.

This dialogue must be confirmed with “continue” to display the catalogue selection.

After closing the catalogue selection, the fittings group is displayed in green in the item list. This shows that this entry cannot be changed directly. If a new fitting requires to be assigned to this entry, it should be activated again. For this purpose the fittings group, which needs to be modified is clicked with the right mouse button. With the help of the entry “Modify” in the menu, this fittings group can be activated again. The entry is displayed in black again and a new fitting or favorite can be allocated to it again.

Page 39: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 39 / 144

3.7.2 The favorite list

All fittings, which were selected in the previous catalogue selection, are saved in favorite sets in the favorite list (2). A favorite set consists of a header and one or more fittings, which were selected during the respective catalogue selection.

If a fittings group is clicked in the item list, then all possible favorite sets for this positioning are displayed in the favorites list and the first favorite set is automatically assigned to the fittings group. If any other favorites set should be assigned to the fittings group, it should be clicked in the favorites list.

In order to view the contents in the individual favorite sets, the entry can be expanded with the help of the plus symbol. A favorite set cannot be modified. If a fitting does not match with a set, then a new favorites set can be selected from the catalogue selection.

A favorite set can only be deleted or renamed. However this functions only if the fittings group in the item list is not displayed in green. The fittings group should first be activated with the “Modify“option in the menu. If the fittings group and the favorites are displayed in black, the individual favorite sets can be deleted or renamed. For this purpose the corresponding entry is clisked upon with the right mouse button and the desired point is selected in the menu. If the favorites set should be renamed, then only the header of the set is changed.

3.8 Export

One can arrive at the display options of SelectionProfessional through the tab “display“.

Page 40: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

40 / 144 SelectionProf_Handbook_EN.pdf

3.8.1 Bill of items – wood

The wood – item list contains all the required components of a cabinet.

Edit

Displays the Bill of Materials- Wood. Remarks can be added. The Bill of Materials – Wood can be subsequently printed or saved as TXT/CSV file.

Print

Prints the bill of items.

Save

Saves the bill of items as a TXT/CSV file.

3.8.2 Hettich order list

The Hettich order list shows all of the fittings that are required for the cabinet and selected from Favourites or the catalogue selection window.

Edit

Presents the Hettich fittings list. Remarks can be added. The Bill of Materials – Wood be subsequently printed or saved as a TXT/CSV File.

Page 41: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 41 / 144

Print

Prints the bill of items.

Save

Saves the bill of items as a TXT/CSV file.

3.8.3 Document Manager

The document manager provides a summary of all information relevant to production. A more detailed explanation can be found in Chapter 5 “Document manager“.

3.8.4 Hesse order list

This list calculates and displays the quantities of lacquer that are required.

All exports and their functions are described in greater detail in "Designer export formats".

3.9 Loading, saving, cabinet library

Cabinets designed in SelectionProfessional can be saved through the Assistants or the program menu (File /Save / Load). Once saved, they can be re-loaded at any time and edited. Saved cabinets can be filed in folders. This allows you to create your own personal cabinet library.

An extensive collection of designs has already been filed for kitchens and offices.

An exact overview of the designs is available in the folder Selection/help/eng „ SelectionProf_Library_EN.PDF “

Page 42: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

42 / 144 SelectionProf_Handbook_EN.pdf

3.10 Hesse Module

Use the Hesse Module to display the finished cupboard and the room situations you have created in photographic quality.

Start the Hesse Module

Once you have drawn a carcase, you can use the “Hesse Module” link to start designing the surface finish. You will find this link in the 3D view of the Designer in the “Construction” Assistant, in the “CAD” CAD Assistant or in the “Roomplan” CAD Assistant.

Choosing a colour / Allocating a lacquer

You will see the window with the colour choices. First select a carrier material. Once you have done so, you need to choose the colour or surface finish.

Click on the right button to choose the colour. .

This displays a new window. Use the arrow to make your colour choice, and then use the green arrow to confirm.

When you have chosen your colour, click on the button in the window for choosing the

surface finish, where you can select the lacquer system. .

When you have worked through and confirmed all the parameters, the cupboard will be created with your chosen surface finishes.

Page 43: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 43 / 144

3.11 Functions in the standard cabinet, sliding and folding, special designs sections

3.11.1 “Insert centre panels" function

Inserts one or more panels in one or more carcase zones. To do this, the desired zone in the carcase must first be selected with the mouse.

Number: number of centre panels

Division: enter the linear division. Examples:

“1:1:1” = two centre panels, evenly spaced.

“400mm:1:1” = two centre panels, clear internal width of first zone 400mm

Zone width: information field for specifying clear internal width of selected zone

Thickness: thickness of centre panels

Front recess: Reference for the front recess. Possible values are “Part and zone” and “Part”.

Reference “Part and zone”: When recessing the centre panels, the zone is also recessed.

Reference “Part”: When inserting the centre panels the zone is not included.

Backset value: measurement for the front recess of the centre panel

Back recess / Backset value: Same function as Front recess

Function “Use connectors”.

Activate or deactivate the use of centre panel connectors

Division: division of the centre panel connectors in the form of linear division

Insertion point: point where the centre panel connectors are inserted

Function “Use wooden dowel“:

Activation or deactivation of the use of the centre panel-wooden dowel

Page 44: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

44 / 144 SelectionProf_Handbook_EN.pdf

Division: Partitioning the centre panel-wooden dowel in the form of linear division

3.11.2 “Insert construction shelves" function

Inserts one or more construction shelves in one or more carcase zones. To do this, the desired zone in the carcase must first be selected with the mouse.

Number: number of centre panels

Division: enter the linear division. Examples:

“1:1:1:1” = three construction shelves, evenly spaced.

“300mm:300 mm” = three construction shelves,

300 mm apart

Zone height: information field for specifying clear height of selected zone

Thickness: thickness of construction shelves

Inside depth: Info-field for the inside height of the selected zone

Front recess: Reference for the front recess. Possible values are “Part and zone” and “Part”.

Reference “Part and zone”: when inserting the construction shelf, the zone is also recessed.

Reference “Part”: when inserting the construction shelf the zone is not recessed.

Backset value:: measurement for the front recess of the construction shelf

Use connectors: Activate or deactivate the use of connectors for the construction shelves

Fucktion “Use wooden dowel“:

Activation or deactivation of the centre panel-wooden dowel

Adjust panel to hole line: Construction shelf spacing is adjusted to the line of holes.

Division: Partitioning the centre panel-wooden dowel in the form of linear division

Insertion point: Insertion point of the construction panel - wooden dowel

Division: Positioning of the connectors for construction shelves in the form of linear division. If “Adjust panel to hole line” is activated, the positioning of connectors for the construction shelves cannot be changed. It is then matched to the position of the hole line.

Insertion point: point where the connectors for the construction shelves are inserted

Page 45: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 45 / 144

3.11.3 “Insert shelves" function”

This function is structured in the same way as the “Insert construction shelf” function.

Loose shelves have a standard recess of 15mm and cannot be used to recess zones.

The options “Use connector“and “Align drawer bottom to hole line“are activated by default.

3.11.4 “Insert drawers" function“

This Assistant inserts one or more InnoTech drawers, wood box with internal drawers, pull-out shelves or front panels in one or more carcase zones. The desired zone in the carcase must first be selected with the mouse. The desired drawer runners are selected from the product tree.

Drawer system

Complete drawer (e.g. InnoTech complete drawers)

Division

Insertion option “Align runner to hole line”: the height of the drawer runners adjusts to the hole line grid.

“Optimum use of space”: places the drawer runners as far down as possible in order to achieve maximum use of the available space.

“Same front panel drill hole”:

the space between the bottom edge of the front panel and the first front panel drill hole is the same for all drawers.

Front panel thickness: thickness of front panel

Drawer front type: Type of drawer front: Standard drawer front, frame drawer front, profile drawer front

Number: number of drawers to be used

Division: entry of linear division. Examples:

”1:1:1“ = three drawers, evenly spaced.

„300mm:1:1“ = front height of the lowest drawer 300 mm, remaining front height is divided equally.

Depth of drawer: Pre-selection of the desired nominal length of the drawer.

Zone height: information field for specifying clear height of selected zone

Inside depth: Info-field for the inside depth of the selected zone

Page 46: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

46 / 144 SelectionProf_Handbook_EN.pdf

Insert internal drawer: If an internal drawer is to be used with the drawer system, this is where to set this option. The program then asks you to specify the insertion point of the first internal drawer. The measurement refers to the last bottom panel / construction shelf.

Recess measurements

Back recess: Minimum space between back drawer edge and back of carcase

Space to top shelf: Minimum space between top of front panel and top panel

Space to bottom shelf: Minimum space between bottom of front panel and bottom panel

Variable width (InnoTech, MultiTech drawers):

The assembly is constructed analogous to the function “pre-assembled drawers“.

Variable drawers can also be inserted outside the grid widths.

Wood box with internal drawer (wooden drawers)

Selection Quadro pull-out / ball-bearing slide (KA) / roller runner (FR)

Division

Insertion option: “Align runner to hole line”: the height of the drawer runners adjusts to the hole line grid.

“Optimum use of space”: places the drawer runners as far down as possible in order to achieve maximum use of the available space.

“Same front panel drill hole”: the space between the bottom edge of the front panel and the first front panel drill hole is the same for all drawers.

Front panel thickness: thickness of front panel

Front panel type: Type of front panel: standard front panel, framed front panel, profiled front panel

Number: number of drawers to be used

Division: entry of linear division. Examples:

”1:1:1“ = three drawers, evenly spaced.

“300mm:1:1“ = front height of first drawer 300mm, other front heights spaced evenly.

Depth of drawers: Information on the required depth of the drawer.

Zone height: information field for specifying clear height of selected zone

Page 47: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 47 / 144

Insert internal drawer: If an internal drawer is to be used with the drawer system, this is where to set this option. The program then asks you to specify the insertion point of the first internal drawer. The measurement refers to the last bottom panel / construction shelf.

Drawer design

Construction drawer front/back:

design option for the front and back panel

„Mitre/mitre“ . Front, rear, side drawers are connected to each other on the mitre.

“inset / inset”: the front and back panel is positioned between the side panel

“none / inset”: the drawer has no front panel; the back panel is positioned between the side panels.

„No / mitre“. The front drawer is to be dispensed with. Rear and side drawers are connected to each other on the mitre.

Thickness: the thickness of the front and back panel

Recess measurement top/front:

the recess measurement from the front panel to the top of the side panels

Recess measurement top/back:

the recess measurement from the back panel to the top of the side panels

Thickness: thickness of side panels

Height: height of side panels

Position of the pullout (for ball bearing slides):

Position of the ball bearing slide on the side drawer; Selection centered: the ball bearing is positioned in the height centered on the side drawer. Selection bottom: The slide position is set on the bottom; the slide position from below the distance from the lower edge of the side drawer to the centre of the ball bearing slide can be specified in the field.

Page 48: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

48 / 144 SelectionProf_Handbook_EN.pdf

Bottom panel:

Construction drawer front/back/side panel

Design option for drawer bottom

„grooved/grooved/grooved“. Drawer base is grooved into the front, rear and side drawers.

“fitted onto/fitted onto/grooved”: drawer bottom fitted onto front and back panel and into side panel grooves.

“fitted onto/fitted onto/inserted”: drawer bottom fitted onto front and back panel and inserted into side panel

„fitted/fitted/fitted“. Drawer base is fitted into front, rear and side drawers.

Thickness: thickness of drawer bottom

Groove depth: depth of drawer bottom groove in side panel

Rebate depth: insert depth of drawer bottom into side panel

Backset value: backset of bottom panel to bottom edge of side panels

Backset values

Backset value back: minimum distance between the back of the drawer and the back of the carcase

Distance to top panel: minimum distance between panel top and the top panel

Distance to bottom panel: minimum distance between panel bottom and bottom panel

Pull-out shelf

A pull-out shelf is a shelf with a front.

Division / backset values:

The structure and functions are the same as the “Wood-box with internal drawer” function.

Front panel: A front panel is a front that has no drawer or runners behind it.

Division: The structure and functions are the same as the “Wood-box with internal drawer” function.

Page 49: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 49 / 144

3.11.5 “Insert internal drawers" function

Internal drawers can be inserted behind normal drawer systems. Before an internal drawer can be inserted, the “Insert internal drawers” option must be selected to set the drawer.

Then, behind the drawer, you must select the zone (in zone mode) which appears in green. You can now select the “Insert internal drawers" function.

Drawer system

Assembly type: „Align extension to hole line“: The guider tracks of the internal drawer align themselves along their height to the latching of the hole line.

„Optimal usage of space“: Sets the internal drawer guider tracks as far as possible towards the bottom, in order to achieve maximum usage of space.

Partitioning: „from below“. The internal drawers are positioned in the cabinet zone.

„from the centre“. The internal drawers are positioned at the centre in the cabinet zone.

Number of thrusts: Number of internal drawers

Zone height: Info-field for the inside height of the selected zone

Indent dimensions

Indent dimension rear: Minimal distance of the internal drawer rear edge to cabinet rear panel

Wood-box with internal drawer/ Quadro / ball-bearin g slide / roller runner

Most functions are structured in the same way as the “Insert drawers – wood-box with internal drawer" dialogues.

Divisioning is adjusted specifically for the interior drawers.

Division

Front panel thickness: thickness of the internal drawer front panel

Rest of zone-height: information field for specifying remaining height of selected zone

Zone height: information field for specifying clear height of selected zone

Page 50: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

50 / 144 SelectionProf_Handbook_EN.pdf

Division of interior drawers:

“same front/distance”: front panels are all the same height; distances between the front panels are all the same.

“variable front/distance”: front panels may differ in height; distances between the front panels may differ

Number: number of internal drawers

Gap: Intermediate space between front panel and top panel, or other construction panels

If the number of internal drawers is more than 1, further fields are activated.

Front panel height: l height of the interior drawer front panel

Gap: distance between the front panels of interior drawers

Page 51: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 51 / 144

3.11.6 “Insert doors" function

This function inserts one or more doors or flaps in one or more carcase zones. To do so, the desired zone in the carcase must first be selected with the mouse. The desired door types may be selected from the product tree.

Side hung doors

Standard door

Division

Align hinge to hole line: Aligns the hinge to the hole line grid

Construction type: type of door hinging

Thickness: thickness of the door

Cup hinge type: type of hinge on the door

“invisible cup hinge”: the catalogue selection contains only automatic hinges with invisible cups

“visible cup hinge”: the catalogue selection contains only Selekta hinges

Opening angle: the range of opening angles available

Zone width: information field for specifying clear width of selected zone

Baffle plate: For double doors, a baffle plate may be chosen. This is directly activated with the installation of the double door. To do this, activate the “Baffle plate” option.

The reference left door, right door may be chosen. Furthermore, the baffle plate type may be specified.

fitted onto

embedded

Page 52: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

52 / 144 SelectionProf_Handbook_EN.pdf

Hinge

Number: number of hinges

Optimal number: Info- field for the optimal number of hinges

Division: Distribution of hinges in the form of linear division. If the “Align hinge to line hole” option is activated, the values specified are approximate dimensions only.

Edge curve: curve on door edge

Zone height: information field for specifying clear height of selected zone

Hinge accessory: „SilentSystem“: During the catalog selection, SilentSystem is offered as accessory of the hinges.

„Push to open“: During the catalog selection, Push-to-Opnen hinges and Push to open magnet are offered as accessory of the hinges.

Assignment: for hinge accessory “SilentSystem“: Assignment of the SilentSystem door dampener in the cabinet width

for hinge accessory “Push to open“: Assignment of Push to open magnets in the cabinet height

Framed door

This function is structured in the same way as the “Side hung doors / standard door" function.

It additionally includes the “Door parameters” for details concerning the frame.

Door parameters

Edge curve: curve on door edge

Filling thickness: thickness of door filling

Frame width: width of door frame

Profiled door

This function is structured in the same way as the “Side hung doors / standard door" function.

It additionally includes the “Door parameters” for details concerning the profile.

Door parameters

Edge curve: curve on door edge

Page 53: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 53 / 144

Profile thickness: thickness of door profile

Profile width: width of door profile

Distance door edge: distance between profile and edge of door

Glass door

This function is structured in the same way as the “Side hung doors / standard door" function.

The door thicknesses are limited to 4 – 6.5 mm.

3.11.7 „Flaps“ function

This function adds one more doors or flaps to one or more carcase zones. To do so, the desired zone in the carcase must first be selected with the mouse. The desired flap types may be selected from the product tree. The suitability of zone size for a flap is calculated in advance. A message is displayed if the zone is too large. Detailed checks are also made in the catalogue to ascertain whether the selected flap is suitable for the situation.

As with doors, flaps are divided into standard flap, framed flap and profiled flap. The “Door parameters” are the same as the functions for the doors.

Standard flap (same as framed flap, profiled flap)

Division

Hinge type: Art des Beschlags (folding-flap fitting, flap fitting, flap lift fitting, Lift-up flap fitting, Flap stay, Top box stay)

Construction type: Mounting type of the flaps (Lift Advanced, Lift Top, Stop left / right / left and right)

Front height top: Height of the top front for Lift Advanced high flap fitting

Front height bottom: Info-field for the bottom front for Lift Advanced high flap fitting

Thickness: thickness of flap

Zone width: information field for specifying clear width of selected zone

Zone height: information field for specifying clear height of selected zone

Edge curve: curve on edge of flap

Page 54: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

54 / 144 SelectionProf_Handbook_EN.pdf

3.11.8 “Select/change knobs/handles" function

This function places or changes knobs and handles on the fronts.

The doors and drawer fronts must first be changed to component mode with the mouse before this can be done.

The fronts are activated in complete groups. If a combination of handle situations is to be used on a front group, individual fronts can be deselected after opening this function.

Front type: Info- field for the front type (is automatically recognised)

Drilling distance: drilling distance for the handles

Material: surface finish on handles or knobs

Order number: order number of the handle or knob

Insertion point: point where handles or knobs are fitted

X distance: horizontal distance between handle or knob and edge of door / drawer

Y distance: vertical distance between handle or knob and edge of door / drawer

Angle: angle of handle or knob

0° with insertion point “top opposite hinge”, “middle opposite hinge" or "bottom opposite hinge" = vertical

0° with insertion point “top middle”, “centred”, “bottom middle” or “top right and left” = horizontal.

Page 55: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 55 / 144

3.11.9 „Locking systems” function

Construction types

The locks are available in different construction types:

Standard cabinet / single cabinet + storage wall construction / overlay + inset

- doors / flaps

- double doors

- drawer systems

- Sliding/folding doors

Office furniture / cupboard LR25+32 / overlay + inset

- Steel drawer (directly activated with the installation of the drawer)

- hanging file frame (directly activated with the installation of the hanging file frame)

- doors

- double doors

Office furniture / desk pedestal LR25+32 / overlay + inset

- steel drawer (directly activated with the installation of the drawer)

- file cradle (directly activated with the installation of the hanging file frame)

- utensil tray (directly activated with the installation of the utensil tray)

- front (directly activated with the installation of the front)

Choice and installation of locking systems

First, the chosen component (door or drawer) is installed. Afterwards, as with the handles, the component that is to be fitted with a lock is chosen. This is done in component mode (red). After the components are chosen, go to “Select/change locks/locking systems“ in the wizard. A dialog box opens.

Front type: The locks can be fitted on the front in different positions. To simplify the choice, a front type (e.g. drawer) should be chosen first. Thus, only the options that fit this type of front will be available.

Page 56: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

56 / 144 SelectionProf_Handbook_EN.pdf

Lock type: A type of lock is chosen

Screw-on lock

Cylinder rotating bar lock

Slam lock

Lever lock

Push bar lock

None No lock

Backset: Depending on lock type, a backset can be chosen.

The backset (x1) is calculated from the centre of the lock to the outside edge of the lock housing.

The actual lock dimension of the front (x2) is calculated from the backset value (x1) + length of bolt + locking angle (x3).

Lock position (x2) in the front = x1 + x3 + overlay

Some lock types have no backset.

For a double swivel door, an espagnolette lock and a push bar lock, the position of the lock can be freely determined. For an espagnolette lock, a back set may be selected; the actual positioning is however carried out on entering the X-distance. Example: Backset = 15, dimension X = 50

If the chosen x value is too small, the minimum value is used automatically.

Page 57: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 57 / 144

Page 58: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

58 / 144 SelectionProf_Handbook_EN.pdf

Insertion point: The insertion point determines the lock position. This works on the same logic as the insertion of handles.

Choice of lock reference with several components

It is possible to fit a double door or several drawers simultaneously. In this case, it is important that the right component for the positioning of the lock is chosen. After the option “Select/change locks/locking systems” is chosen, all components (red) are highlighted. Click on the various components to deselect (blue) or reselect (red) them.

The chosen locking system is only fitted to the selected components.

The selected locking system can be built in for the activated components only.

Activate / deactivate doors

Activate / deactivate drawers

Page 59: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 59 / 144

3.11.10 “Insert cabinet accessories" function”

This function inserts cupboard accessories such as hanging rails into one or more carcase zones. To do so, the desired zone in the carcase must first be selected with the mouse.

Construction: mode of inserting hanging rail

“on construction panel”: the hanging rail is inserted with a construction shelf

“on side”: the hanging rail is attached to the carcase / centre panels.

Distance from bottom (mm):

insertion point of hanging rails from bottom

Zone height: information field for specifying clear height of selected zone

Zone depth: information field for specifying clear height of selected zone

Thickness: thickness of construction shelf

The details for the construction shelf are the same as the details for the “Insert construction shelf" function.

3.11.11 “Insert front divider” and “Insert zone di vider" function

Zones are usually formed by construction shelves or centre panels. Sometimes it is necessary for a zone not to be divided by a part. In kitchen base units, for instance, a drawer is often positioned above a side hung door.

The “Insert front divider” and “Insert zone divider” functions are used to insert help lines. These create new zones without appearing later in the design or parts list. They appear as small lines in the preview.

Absolute reference of front divider:

The reference line is set with relation to the front dimension.

Absolute reference of zone divider:

The reference line is set with reletion to the inside dimension.

Alignment: alignment of the divider

Zone height information field for specifying clear height of selected zone

Zone width: information field for specifying clear width of selected zone

Page 60: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

60 / 144 SelectionProf_Handbook_EN.pdf

Division: distribution of front dividers in the form of linear division

3.12 Functions in the office cabinet section

3.12.1 “Insert construction shelf" function

Inserts one or more construction shelves in one or more carcase zones. To do so, the desired zone in the carcase must first be selected with the mouse.

Distance in HU: the fitted height of the construction shelf in height units. In the office segment, shelves can only be inserted in height units.

HU in mm: information field for specifying the height units in mm in the selected HU

Number: number of construction shelves

Zone height: information field for specifying clear height of selected zone

Thickness: thickness of construction shelves

Front recess: size of front recess for construction shelves

Back recess: size of back recess for construction shelves

Clear depth: information field for specifying clear depth of selected zone

Use connectors: use of construction shelves - activate or deactivate connectors

Division: distribution of construction shelves – connectors in the form of linear division

Insertion point: point where construction shelf connectors are inserted

Use wooden dowel: Using the construction panel - activating or deactivating the wooden dowel

Partition: Partition of the construction panel – wooden dowel in the form of linear division

Insertion point: Insertion point of the construction panel – wooden dowel

3.12.2 “Insert shelves" function”

This function is structured in the same way as the “Insert construction shelf” function.

Loose shelves have a standard recess of 15mm and cannot be used to recess zones.

The options “use connector“and “align base to hole line“are activated by default.

Page 61: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 61 / 144

3.12.3 “Insert drawers" function“

This function inserts one ore more Office drawers without locks in a carcase zone. To do so, the desired zone in the carcase must first be selected with the mouse. The desired drawer type is selected from the product tree.

Calculations in the office segment are always performed in height units (HU). The front heights are based on these height units. Only one drawer can be inserted at a time.

Front panel

Partition

Version: Front panel version

Height (in HE): Height of the front panel in height units

Minimum height (in mm): Info-field on the minimum required front height in mm

Maximum height (in HE): Info-field on the maximum available height in height units

Maximum height (in mm): Info-field on the maximum available height in mm

Front panel thickness: Front panel thickness

Zone width: Info-field on the inside width of the selected zone

Wide drawer without lock

Division

Type: design of wide drawer

This selection influences “Height (in HU)”. Example: “Wide drawer A5 vertical” requires 4HU; the value is automatically entered in the field “Height (in HU)”

The height can also be entered directly in height units in “Height (in HU)”.

Height (in HU): height of wide drawer in height units

Minimum height (in mm): information field for specifying minimum required front panel height in mm

Maximum height (in HU): information field for specifying maximum available height in height units

Maximum height (in mm): information field for specifying maximum available height in mm

Front panel thickness: thickness of wide drawer front panel

Zone width: information field for specifying clear width of selected zone

Zone height: information field for specifying clear height of selected zone

Page 62: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

62 / 144 SelectionProf_Handbook_EN.pdf

Suspension cradle without lock

Division

Functions the same as wide drawer without lock. Other heights are available under “Type”. Suspension cradles are available in the catalogue selection.

3.12.4 “Insert internal drawer" function

In the office segment, internal drawers can be used behind side hung doors. The door needs to be positioned first, then the zone behind the door can be selected and the drawers inserted.

Here, too, the distinction is made between wide drawers and suspension cradles.

The functions are the same as the “Wide drawers/hanging frames without lock” functions.

3.12.5 “Insert drawers with lock" function

This function inserts one or more office drawers with locks in a carcase zone.

To do so, the desired zone in the carcase must first be selected with the mouse. The drawer with the lock is always the last drawer. This is why the front panel is automatically adjusted to meet the next construction shelf. The front requires one extra HU for the lock; this is added on automatically.

Front panel with lock

Partition

Functions analogous to the “front panel without lock“function

Type: „Stop Control“or „Stop Control Plus“

Lock position from top: Drilling position of the lock in the front panel from front panel top edge

Page 63: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 63 / 144

Wide drawer with lock

Division

Functions the same as the “Wide drawer without lock” function

Anti-tilt: selection of anti-tilt mechanism with or without lock

Type: „Stop Control“ or „Stop Control Plus“

Lock position from top: drilling position for lock from top edge of front panel

Suspension cradle with lock

Division

Functions are the same as the “Wide drawer with lock” function

3.13 Functions in the Office-Container section

3.13.1 “Insert drawers" function

This function inserts one ore more Office drawers without locks in a carcase zone. To do so, the desired zone in the carcase must first be selected with the mouse. The desired drawer type is selected from the product tree.

Calculations in the office segment are always performed in height units (HU). The front heights are based on these height units. Only one drawer can be inserted at a time.

Front panel

Partition

Version: Front panel version

Height (in HE): Height of the front panel in height units

Minimum height (in mm): Info-field on the minimum required front height in mm

Maximum height (in HE): Info-field on the maximum available height in height units

Maximum height (in mm): Info-field on the maximum available height in mm

Front panel thickness: Front panel thickness

Zone width: Info-field on the inside width of the selected zone

Zone height: Info-field on the inside height of the selected zone

Page 64: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

64 / 144 SelectionProf_Handbook_EN.pdf

Pencil drawer

Division

Typ: design of the pencil drawer

Height (in HU): the height of the pencil drawer measured in height units

Minimum height (in mm): information field for specifying minimum front panel height required in mm

Maximum height (in HE): information field for specifying maximum available height in height units

Maximum height (in mm): information field for specifying maximum available height in mm

Front panel thickness: thickness of pencil drawer front panel

Zone width: information field for specifying clear width of selected zone

Zone height: information field for specifying clear height of selected zone

Steel drawer

Division

Type: design of the steel drawer

This selection influences “Height (in HU)”. The height can also be entered directly in height units under “Height (in HU)”.

Height (in HE): Height of the steel drawer in height units

Minimum height (in mm): Info-field on the minimum required front height in mm

Maximum height (in HE): Info-field on the maximum available height in height units

Maximum height (in mm): Info-field on the maximum available height in mm

Front panel thickness: Steel drawer front panel thickness

Zone width: Info-field on the inside width of the selected zone

Zone height: Info-field on the inside height of the selected zone

Drawer with Hanging file frames

The functions are analogous to the contents of the “steel drawer“section.

The hanging file frame has deviating default values in the “Version“section.

Page 65: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 65 / 144

3.13.2 “Insert drawers with lock" function

A lock can be fitted to the last drawer of a pedestal.

The insertion functions are the same as the functions for the drawers without a lock.

Anti-tilt: selection of anti-tilt mechanism with or without a lock

Type: „Stop Control“ or „Stop Control Plus“

Lock position from top: drilling position for lock in front panel from bottom front panel edge

3.14 Sliding and Folding Constructions in Selection Professional

3.14.1 Differentiation of application area

There are different sliding and folding systems in the Hettich product portfolio.

Depending on the selection of fitting and application, cabinets can be designed in

SelectionProfessional respectively.

Stand-Alone Sliding and Folding Door Cabinets

In the case of stand-alone sliding and folding door cabinets, carcase constructions

follow the fitting. Particularely base and bottom shelf solutions have to be carried out

respectively.

Examples for these constructions:

WingLine 770/780

Normal shelves and construction shelves can be inserted in these types of

constructions. Moreover, important construction details like cabinet side thickness,

height, rear panel construction and others may be alterred.

Page 66: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

66 / 144 SelectionProf_Handbook_EN.pdf

Integrated Sliding and Folding Constructions

In the case of integrated sliding and folding constructions the fittings will be inserted into

an existing standard cabinet. Sliding and folding fittings can be combined with drawers,

doors and open racks.

WingLine 170 SlideLine 55/56

Example costruction in SelectionProfessional:

Shelves, doors, sliding doors and drawers in one

constrcution.

Page 67: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 67 / 144

3.14.2 Selection of Fittings in SelectionProfession al

The desired sliding and folding construction can be selected from the Construction Assistant.

The following constructions are possible:

- Sliding door cabinet overlay

- Sliding door cabinet inset

- Folding door cabinet

- Folding-sliding door cabinet

Carcase details can be defined like in any standard cabinet. Please note that the usage of fittings is dependent on the specified carcase dimensions.

Page 68: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

68 / 144 SelectionProf_Handbook_EN.pdf

3.14.3 Fitting: TopLine 22 standard doors

Input / Options in SelectionProfessional

Construction: sliding door cabinets / overlay

Carcase size: Height = 300 – 3500 mm

Width = 1000 – 4500 mm The minimum width is dependent on the door width. The minimum door width is 500mm.

With 2 doors min. carcase width = 1000mm,

with 3 doors min. carcase width = 1500mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance / panel height = 50 – 300mm

Door division: Guide tracks= double tracked

Number of doors= 2 or 3

Depending on the number of doors, the respective set of fittings will be selected.

Widths of doors = 500 – 2000 mm

Front details: Door thickness front = 16 – 28 mm Door thickness back= 16 – 28 mm

Depending on the door thickness, the respective set of fittings will be selected. 16 – 21mm > door center distance 29mm

22 – 28mm > door center distance 36mm

Front gaps left = 0 – 60mm

Front gaps right = 0 – 60mm

Page 69: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 69 / 144

3.14.4 TopLine 25/27

Input / Options in SelectionProfessional

Construction: Sliding door cabinet / inset

Carcase size: Height = 300 – 3500 mm

Width = 1000 – 4500 mm

The minimum width is dependent on the door width. The minimum door width is 500mm.

With 1 door and 2 doors min. carcase width = 1000mm, with 3 doors min. carcase width = 1500mm,

with 3 doors min. carcase width = 1500mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance / panel height = 50 – 300mm

Door division: Guide tracks = single tracked / double tracked

Number of doors = 1 (only single tracked), 2 or 3

Depending on the door thickness, the respective set of fittings will be selected

Door width = 500 – 1500 mm

Front details: Door thickness front = 16 – 45 mm Door thickness back = 16 – 45 mm

Front gaps left = 0 – 60mm

Front gaps right = 0 – 60mm

The bottom runner (STB 11, 12, 15, 35) will be selected through the accessory in the catalogue.

Page 70: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

70 / 144 SelectionProf_Handbook_EN.pdf

3.14.5 Fitting: TopLine 1

Input / Options in SelectionProfessional

Construction: Sliding door cabinet / inset

Carcase size: Height = 300 – 3500 mm

Width = 1000 – 4500 mm

The minimum width is dependent on the door width. The minimum door width is 500mm.

With 2 doors min. carcase width = 1000mm,

with 3 doors min. carcase width = 1500mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance / panel height = 50 – 300mm

Door division: Guide tracks = double tracked

Number of doors = 2 / 3

Depending on the number of doors, the respective set of fittings will be selected

Door widths = 500 – 2000 mm

Front details: Door thickness front = 16 – 30 mm Door thickness back= 16 – 30 mm

Front gaps left = 0 – 60mm

Front gaps right = 0 – 60mm

The bottom runner (STB 11, 12, 15, 35) will be selected through the accessory in the catalogue.

Page 71: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 71 / 144

3.14.6 Fitting: WingLine 770/780

Input / Options in SelectionProfessional

Construction: Folding door cabinet

Carcase size: Height = 300 – 2200 mm

Width = 500 – 2400 mm The minimum width is dependent on the width of the door wing. The minimum width of the door wing is 245mm.

With 2 wings min. carcase width = 500mm,

with 4 wings min. carcase width = 1000mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance = 15 – 1000 mm

Front details: Thickness = 16 – 25 mm Edge curve = 10mm – 99mm

The curved edge will not be displayed, but should be defined for safety reasons (risk of injury)!

Front overlay left = 1 – 15 mm

Front overlay right = 1 – 15 mm

Front overlay top = 1 – 99 mm

Clearance = 1 – 5 mm

Door stop = right, left, right and left

Depending on the door stop, the respective set of fittings will be selected.

Front details / Hinge: Number = 4 - 8

Division = freely > distance between the first and last hinge Top distance = 50 – 500 mm

Bottom distance = 50 – 500 mm

Page 72: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

72 / 144 SelectionProf_Handbook_EN.pdf

3.14.7 Fitting: WingLine 77

Input / Options in SelectionProfessional

Construction: Folding door cabinet

Carcase size: Height = 300 – 2400 mm

Width = 500 – 2400 mm The minimum width is dependent on the width of the door wing. The minimum width of the door wing is 245mm.

With 2 wings min. carcase width = 500mm,

with 4 wings min. carcase width = 1000mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance / panel height = 15 – 1000 mm

Front details: Thickness = 16 – 25 mm Edge curve = 10mm – 99mm

The curved edge will not be displayed, but should be defined for safety reasons (risk of injury)!

Front overlay Left = 1 – 15 mm

Front overlay Right = 1 – 15 mm

Front overlay Top = 1 – 99 mm

Clearance = 1 – 5 mm

Door stop = right, left, right and left

Depending on the door stop, the respective set of fittings will be selected.

Front details / hinge: Number = 4 - 8

Division = freely > distance between the first and last hinge

Top distance = 50 – 500 mm

Bottom distance = 50 – 500 mm

Page 73: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 73 / 144

3.14.8 Fitting: Wing 77

Input / Options in SelectionProfessional

Construction: Folding-sliding door cabinet

Carcase size: Height = 300 – 2400 mm

Width = 500 – 2400 mm

Cabinet side: Thickness = 5 – 100 mm

Base: Door distance / panel height = 45 – 1000 mm

Front details: Thickness = 16 – 25 mm Edge curve = 10 – 99mm

The curved edge will not be displayed, but should be defined for safety reasons (risk of injury)!

Front overlay Left = 1 – 15 mm

Front overlay Right = 1 – 15 mm

Front overlay Top = 1 – 99 mm

Number of doors: the amount of doors will be calculated based on the width of the carcase.

Carcase width 500 – 1000 > 2 wings

Carcase width 1001 – 2000 > 4 wings

The maximum door wing width is 400mm.

Page 74: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

74 / 144 SelectionProf_Handbook_EN.pdf

3.14.9 Integrated Sliding and Folding Door Constru ctions

The sliding and folding option is directly selected from Assistant – Carcase divisioning. First, a standard cabinet (overlay or inset) is defined.

After that center panels and construction shelves are used to divide the cabinet and create different zones. In each individual zone, sliding and folding doors can be inserted. Different types of fittings can be used every other zone.

One zone can be equiped with doors, another one can be equiped with drawers. A third one could be equiped with a sliding or folding door.

The respective zone needs to be marked in green (Zone mode). From the Assistant choose Insert sliding/folding doors.

A window opens with the different types of fittings.

Different types of fittings are suitable for certain zone sizes:

Type of fitting Zone height Zone width Zone depth

SlideLine 55/56 300 - 2000 300 – 3000 50 - 2000

TopLine 110 300 - 2000 300 – 3000 50 - 2000

WingLine 170 300 – 2250 300 – 1250 340 - 2000

Page 75: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 75 / 144

WingLine 26 800 – 1850 300 – 1050 50 - 2000

3.14.10 SlideLine 55 / 56

Front details

Doors – backset value: 0 – 100 mm

Door thickness front / back: 15 / 16 / 18 / 19 / 22

Front gaps – laterally: 0 – 20 mm

Door division

Guiding tracks single track / double track

Number of doors 1 (only single track), 2 or 3

Sequence of doors left door behind right door / right door behind left door

Door width Same door width / Identical view

Overlapping 0 – 60 mm

Door spacing Clear / Fixed

Clear = Door spacing can be selected freely between 6 – 50 mm.

Fixed = A fixed screw-on running profile will be selected.

Distance value = freely = 6 – 50mm, fixed= depending on door thickness

Page 76: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

76 / 144 SelectionProf_Handbook_EN.pdf

3.14.11 TopLine 110

Front details

Doors – backset value 0 – 100 mm

Door thickness front / back 15 / 16 / 18 / 19 / 22

Front gaps – laterally 0 – 20 m

Door division

Guiding tracks single track / double track

Number of doors 1 (only single track), 2

Sequence of doors left door behind right door / / right door behind left door

Door width Same door width / dentical view

Overlapping 0 – 60 mm

Door spacing spacing between doors is set to 10 mm

Page 77: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 77 / 144

3.14.12 WingLine 170

Division

Align hinge to hole line On / Off

Construction type Stop left / Stop right / double door for carcase widths > 640mm, a double door will be selected automatically.

Thickness 15- 28 mm

Hinge

Number number of hinges

Optimum amount infofield, the opt. number of hinges can be undercut at the user’s own risk. A warning will show up.

Division division of hinges in door

Edge curve used to calculate the C-measurement / distance plate but not displayed in the drawing

Opening angle to specify the opening angle of the door

The different folding door hinges can be selected from the catalogue.

The mounting position of the guiding bar will be disregarded.

Page 78: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

78 / 144 SelectionProf_Handbook_EN.pdf

3.14.13 WingLine 26

Division

Align hinge to hole line On / Off

Construction Stop left / Stop right / double door for carcase widths > 500mm, stop left and stop right will be selected automatically.

Thickness 15- 28 mm

Clearance 1 – 5 mm

Overlay left 1 – 15 mm

Overlay right 1 – 15 mm

Hinge

Number number of hinges

Optimale Anzahl infofield, the opt. number of hinges can be undercut at the user’s own risk. A warning will show up.

Division division of hinges in door

Edge curve used to calculate the C-measurement / distance plate but not displayed in the drawing

Opening angle always with 110° hinges

The different folding door hinges can be selected from the catalogue.

Page 79: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 79 / 144

3.15 Placing Handles on Sliding and Folding Doors

3.15.1 Placement Choices

Handles and knobs can be placed on sliding and folding doors similarly to drawers and doors. However, there are differences based on the arrangement of the doors.

3.15.2 Placement of Handles

1) Select the sliding or folding door in the (red) constructive part mode.

2) Choose „Select/change knobs/handles“ from the Assistant. The construction is displayed in the front view.

3) Especially in sliding and folding door constructions with several doors, it is necessary to place the handles on different positions. By default the handles are placed on all selected fronts marked in red. To avoid this, fronts can be selected individually.

Process:

Initially all fronts are marked in red. To select the handle position only for the left sliding door, click on the middle and right door to unselect them.

Subsequently, the handle position will be selected for the left door by choosing „middle left“ for example. Confirm you selection by clicking on the green checkmark.

The handles for the remaining doors are placed likewise.

Page 80: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

80 / 144 SelectionProf_Handbook_EN.pdf

3.16 Kitchen Constructions

3.16.1 Construction types

A separate kitchen constructions section has been created. These constructions are specifically aimed at the kitchen area, which means for example that all panel dimensions are optimised for a perfect kitchen environment.

The kitchen constructions are divided into the sections base cabinet / top unit / tall cabinet. The base unit section is furthermore divided into the areas standard base cabinet and corner cabinet.

Dimensional references and design details are furnished in the “SelectionProf_Library_EN.PDF “handbook.

3.16.2 Full circle carousel fitting

Input / choice in SelectionProfessional

Carcase size

Mounting situation: Choice of fitting type

750 Arena, 750 Wire, 750 Wire white, 650 Wire white

Only the relevant accessories must be chosen from the catalogue, if necessary.

Width: Dimension A

Complete external carcase width

Carcase side left / front: Dimension B

External carcase side depth. These always have the same value.

Door width: Dimension C

The door width is an info field and is calculated from the width of the carcase side left / front.

Page 81: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 81 / 144

Construction information: The carcase is made with an 8 mm back panel. The rear back panel is constructed from 16/18/19 top thickness.

Base

An angled base represents a special situation with regards to base recess. The base recess measurements (from the front) normally relate to a 90° angle between the bottom shelf and the front edge of the base.

If the same measurements were used for an angled cabinet as for a normal base cabinet, the two base fronts would not fit together.

The program therefore allows for the recess measurement in relation to the carcase side to be specified. The distance in the 90° angle is given as info text.

Fitting information

Mounting top panel: centre hole (D=5 mm, T=8 mm) + 3 fixing holes

Mounting bottom panel: 3 fixing holes. To enable better centring and positioning of the revolving plate, a punch point has been provided in the centre of the fitting. There is no need for mounting or drilling at this point.

Choice of hinge: The door construction requires angled hinges (W45). These can be chosen from the catalogue.

Corner carousel fitting: The full circle carousel fitting can be chosen from the catalogue. The set already contains two revolving bases so that these do not need to be chosen separately.

Page 82: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

82 / 144 SelectionProf_Handbook_EN.pdf

3.16.3 Segmented carousel fitting

The segmented carousel fitting is identical with the full-circle carousel in terms of carcase size and fitting choice.

3.16.4 Three quarter carousel fitting

Input / choice in SelectionProfessional

Carcase size

Mounting situation: Choice of fitting type700 Arena, 820 Wire, 700 Wire, 820 Wire, 700 Wire white, 820 Wire white

Only the relevant accessories must be chosen from the catalogue, if necessary.

Carcase side left / front: Dimension A

External carcase side depth. These always have the same value.

Opening width: Dimension B

Aperture for the door

Page 83: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 83 / 144

Front information

Door variants: The doors are available in different construction types:

Equal

Left short

Right short

Folding door stop left

Folding door stop right

Fitting information

The options equal, left short and right short are carried out with Intermat hinges (125-165° opening angle).

The options Folding door stop left and Folding door stop left are offered in combination with a wide angle hinge and a corner cabinet folding door hinge.

Page 84: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

84 / 144 SelectionProf_Handbook_EN.pdf

3.16.5 Corner cabinet Revo 45

Input / choice in SelectionProfessional

Carcase size

Carcase height: The carcase height of the Revo 45 and 90 is not identical with the carcase height of a normal base cabinet.

The fronts of the Revo 45/90 rotate inside the carcase when being opened. Both construction types therefore have no top panel. There is a clearance gap between the front and the bottom panel. If a Revo 45/90 cabinet is constructed at the same height as a normal base cabinet, both fronts would be offset at the bottom. The ordinary base cabinet features an overlay on the bottom panel. The front of the Revo 45/90 has a recess to the bottom panel (clearance).

A = corner cabinet Revo 90/45; H = 747mm

B = normal base cabinet; H = 720mm

1 = bottom panel corner cabinet

2 = bottom panel normal cabinet

C = bottom panel overlay

Overlay = 16 mm, clearance = 4mm

11 mm = gap between door and bottom panel with Revo 90/45

27 mm = offset value of carcase height, 720 mm + 27 mm = 747 mm

Page 85: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 85 / 144

Carcase width: The carcase width and side depth are fixed and cannot be changed. They are in line with ideal fitting values.

Front: A straight wooden front is fitted. The stainless steel finish front is not being considered.

The front measurements can be fixed depending on side panel thickness.

Side panel thickness

A - opening width B - door width

19 454 446

18 456 448

16 458 450

Page 86: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

86 / 144 SelectionProf_Handbook_EN.pdf

Bottom panel / base

The bottom panel is recessed by 40 mm in order to be invisible from the outside. This also allows for the side to be notched. The base is thus offset in relation to the bottom panel by another 10 mm towards the back.

A = bottom panel, recessed by the value x1

B = bottom panel, recessed by the value x2

C = door

Side notch = 11 mm + bottom panel thickness

Page 87: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 87 / 144

3.16.6 Corner cabinet Revo 90

Input / choice in SelectionProfessional

Carcase size

Mounting situation: There is a choice between the carcase sizes 800*800 and 900*900.

Carcase height: Starting basis analogous to Revo 45

Carcase width: The carcase width and side depth are fixed and cannot be changed. They are in line with ideal fitting values.

Top panel The Revo 90 does not feature a top panel.

Bottom panel / base The construction of recess measurements for bottom panel and base is identical with that for Revo 45.

Page 88: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

88 / 144 SelectionProf_Handbook_EN.pdf

3.16.7 Semi circle carousel fitting

Input / choice in SelectionProfessional

Left / right variation

The semi circle carousel fitting is available in a left and right version. The two construction types are laterally reversed. The fittings for both versions are identical.

Left option Right option

Carcase size

Mounting situation: There is a choice between 850 Arena, 850 Wire and 750 Arena.

Width: Dimension A, carcase width

Door width: Dimension B, door width

Mounting width: Dimension C, info field, non-changeable, important for the installation of the next base cabinet

Door opening width: Dimension D, info field, non-changeable

Depth: Dimension E, carcase depth

Page 89: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 89 / 144

Correlation between the dimensions

A change to the width (dimension A) of the cabinet has implications on the mounting width (dimension C). The door width (dimension B) remains unchanged.

A change to the door width (dimension B) has implications on the carcase width (dimension A). The mounting width remains unchanged.

Aperture angle

Visible angle length 0° = angle length A

Visible angle length 90° = angle length B

Info post: The post dimension remains constant.

Front information

Height hinge bottom / height hinge top:

The hinge positions are given from the bottom. Please ensure that there is no clash with the mounting flaps of the revolving centre.

Page 90: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

90 / 144 SelectionProf_Handbook_EN.pdf

4. Selection CAD (AutoCAD) Principles

4.1 Introduction to CAD

The Designer part of SelectionProfessional allows you to create, modify and save complete cabinet designs. Automatic measuring using the Document Manager can also be started from the Designer

The AutoCAD section is used primarily for the following:

- Exact 3D view and display, with all details of fittings and design elements

- Dimensioning individual components selected

- Dimensioning the carcase view

- Exporting the cabinet in DWG/DXF format

- Cabinet print-out / plot

Roomplan is based on the AutoCAD system and is therefore also started from the AutoCAD environment.

4.2 AutoCAD surface

4.2.1 Menu functions

File

New Creates an blank page

Import Imports AutoCAD drawings

Export Exports AutoCAD drawings

Plot Prints the current drawing

Preferences AutoCAD settings; do not change

End Ends the program. SelectionProfessional should be closed through the Designer and not using this AutoCAD function.

Edit

Undo Reverses a step in a function

Repeat Repeats a step in a function

Info CAD Information on a component

Info Designer Information on a component

Delete cabinet Deletes an entire cabinet

Delete cabinet from list Deletes a specific cabinet from several inserted cabinets

Delete Part Deletes individual lines, dimensions, decorative elements etc.

Page 91: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 91 / 144

View

Display details … Sets the viewing details. There is a speed advantage in lower representations, particularly with more complex designs. Low = Display cabinet contours, no fittings Medium = Includes fittings in the display High = Displays fittings and drill holes

Drawing … Sets the various AutoCAD views.

Zoom > Various options for zooming in and out

BKS-Symbol on/off Enables or disables the coordinates

Pan Move drawing

Hide edges Provides a partly hidden view of the cabinet. Note: this view is not automatically printed.

3D wire model Makes circles clearer, switches from hidden mode back to wire.

3D surface display Shades the surface

Colored display displays the design with the selected outer surface

Set up project Displays the typed component only

Hide elements Hides individual sides, walls etc.

Display all Shows all sides, walls etc again.

Assistant If the Assistant is switched off, it can be switched back on again using this function.

Tools

Dimension Part > Selects component dimensioning

Manual dimension Dimensioning function for cabinet views

Measure Measures a defined distance

Image output on …> Prints out the screen content. The content can also be copied to a file.

Text Adds a text commentary to the drawing.

Toolbox > Contains simple drawing commands

Window In SelectionProfessional there is a main window that displays the current Designer drawing. This window must never be closed. Other windows may be opened in addition to this window in order to plan a room plan alongside your Designer work. The individual windows are displayed in the menu.

? Information on SelectionProfessional

Page 92: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

92 / 144 SelectionProf_Handbook_EN.pdf

4.2.2 AutoCAD icon functions

The icons are described from left to right.

- creates a new request - Opens an existing file or looks for it - Saves the active file with the current file name, location and file format - Prints the active drawing. Click on Print in the File menu to select print options

- Undoes the current action. Goes back one step in the list of actions - Repeat action. Repeats the most recent action

- Pressing this button displays the entire design on the screen - Pressing this button magnifies an area of the design - Pressing this button magnifies the screen view of the design - Pressing this button reduces the screen view of the design - Zooming in real time. Press the left mouse button to zoom into the screen view - Pan function. The screen view can be shifted by holding the left mouse key down

- Top view. View of the design from above - Side view left. View of the design from the left - Side view right. View of the design from the right - Front view. View of the design from the front - Back view. View of the design from behind - Isometric view south-west - Isometric view south-east - Isometric view north-east - Isometric view north-west - 3D orbit. In this view, the room can be moved freely in any direction. - 3D wire model function - Hide edges - 3D surface display - Colored display - Light symbols on/off

- Delete Part. Deletes an entire cabinet. - The design you want to delete can be selected after clicking this button - A highlighted component can be deleted after clicking this button. Click the button. The cursor changes. Highlight a component and then press on ENTER

Page 93: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 93 / 144

- After clicking this button you can drag a text box in the screen view and insert any text of your choice - Measure a distance between two points - Manual dimensioning of the drawing - Aligned dimensioning of the drawing - continues the measuring from point one - measures the diameter of bores etc. - Dimension part. Creates a dimensioned drawing of a specific component - Rotate dimensioned item in direction X - Rotate dimensioned item in direction XY - This function takes you back to the starting picture when you have finished dimensioning.

- Isolates a component, so that only that component is displayed - Move item. Use this function to move the chosen item anywhere in the room. - Rotate item. Use this function to turn the chosen item by hand. First select a rotation point with the mouse, and then rotate the item around this point. - inserts an item again

4.3 Create job

New room plannings or changes made to existing room plannings are saved with these functions. Here a preview of the room is saved and information such as commission, end customer, name of the processor etc. can be entered.

Page 94: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

94 / 144 SelectionProf_Handbook_EN.pdf

4.3.1 Comparison of the individual save functions i n SelectionProfessional

Saving in Designer The cabinet that has been created in the Designer is saved. The cabinet is saved in a predefined directory, which can be optionally expanded. The directory path is on C:\Selection\User\CAD (here C:\Selection is the installation directory of SelectionProfessional)

File > Export in Designer To open cabinets on another computer with the help of SelectionProfessional, they have to be exported first. For this the cabinet should not be open in Designer. If the function”Export“is selected in File menu, the cabinets that have to be exported should be selected first. The second step is to specify a target folder. Any directory can be specified as the target folder. Subsequently the cabinet can be copied into the directory with the File -> Import function. It can be now opened here.

Create job/project The “create job / project” function is used to save a new spatial planning. All information about this job is stored in a database.

File > Export in SelectionCAD To open spaces on another computer with SelectionProfessional, they should be exported first. The room/space should be open. After clicking on the “Export” function in File menu in SelectionCAD, a target folder is specified. Subsequently the room can be opened on another computer with the File -> Import function in SelectionCAD. In order to open this room in the future with the” Load job/project” function, it should be first saved with the “Save job/project” function.

Page 95: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 95 / 144

4.3.2 Create job/project

New spatial/room planning is saved with the “Create job/project“function.

To create a new job, it is necessary to create a new room situation. Otherwise it will not be possible to create additional information.

The dialogue “Save job“is opened after calling the function.

Here the job name (1) and the additional information (2) is entered and saved with the green check mark. Subsequently the job name is saved in the job list (4).

The preview (3) is created with the help of the view in SelectionCAD. It is not considered here, whether the edges have been hidden beforehand.

All jobs that have been opened until now (5) are listed in the list of opened jobs.

Page 96: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

96 / 144 SelectionProf_Handbook_EN.pdf

The menu bar (6) is configured as follows:

• deletes an existing job

• creates a new directory in the job list

• updates the job list

• searches for a job

• calls Help

4.3.3 Load job / project

All available room plannings are opened with the “load job/project” function. The dialogue corresponds to the Save job dialogue.

4.3.4 Save job / project

All changes made to the available room plannings are saved with the “Save job/project“function. The existing job is overwritten.

Page 97: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 97 / 144

4.4 Measuring

4.4.1 Dimension part

Click “Dimension Part” to dimension various components of a cabinet (sides,

shelves, doors etc.).

Clicking the “Dimension Part” button changes the mouse pointer into a small box. Click

the box on the outline of the component (see figure below). The component will then be

displayed with its dimensions.

To dimension other parts, click the "Dimension Part" button again and select another

component. Click the Return to CAD button to finish dimensioning

With the “Rotate measured item X“button and “Rotate measured item XY“ button,

the measured components can be rotated.

The type of dimensioning can be set under “Tools / Dimension Part / Settings …”.

Style

Absolute = absolute dimensioning of the bottom left side of the carcase

Hole centre to hole centre = relative dimensioning from drill hole to drill hole

Page 98: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

98 / 144 SelectionProf_Handbook_EN.pdf

Unit

millimetre = sets dimensioning to mm units

inch = sets dimensioning to inch units

Generate infotext = if this option is activated, information such as slot depths, drill

diameters, drilling depths etc. is also shown.

4.4.2 View dimensioning

You can perform your own dimensioning by using

the “Apply Measure” button or ”align with

dimensioning“ . You can, for example, select the

front view of the cabinet and dimension it yourself.

To do this, select the function and enter the point

where dimensioning is to start. Click on the carcase

edge and set the starting point of the dimensioning,

then select the point where dimensioning is to end,

followed by the position of the measurement line.

The program supports you with automatic capture

functions. This means that it automatically looks for

and finds the end of a line. This is indicated by a

small violet square. Once you see this, all you have

to do is left-click the mouse and the end point is

recognised.

With the “Continue dimensioning” button , it is possible to attach a chain

dimensioning to the most recently created dimensioning.

With the “diameter” button, curves and circles can be measured.

With the “measure” button, it is possible to remove a measure from the view, without

the creation of a dimensioning. The measured space can be read in the status bar.

With the “Text” button , it is possible to write text information in the view, so that it

can be printed along with.

Page 99: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 99 / 144

4.4.3 Cabinet views

With the help of the menu item “View / display details“, the view details scale can be set.

- Low: Only handles and components are displayed. This accuracy of detail is especially suitable for room planning.

- Medium: Components, handles and fittings are displayed without processing.

- High: Components, handles and fittings are displayed along with processing.

With the help of the View button or the menu option “View/designs-… “, a cabinet

display can be selected.

“Hide edges” gives you a partly hidden view of the cabinet.

With the “3D area representation“, a hidden and colored view of the

cabinet is available.

Page 100: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

100 / 144 SelectionProf_Handbook_EN.pdf

4.5 Printing/plotting

In order to understand the following points on the subject of printing/plotting, it is better

to implement a cabinet design beforehand.

Screen layout

Everything that can be displayed on the screen can also be printed. These may include perspective views of a cabinet, dimensioned components (side panels, top panels, bottom panels, etc.) or enlarged sections or room views.

Before you print a drawing, it is a good idea to display it on the screen in the way you

want to print it. For instance, if you want to print a perspective view of a cabinet, then

position the drawing as shown below. The quickest way to arrange a drawing as shown

below is by clicking the Full view button. If you only want to print a section of the

cabinet, e.g. a corner connection, use the Zoom window button.

If the hidden cabinet edges are not to be printed, the “Hide edges“button or the

menu “View / hide edges” is used so that the invisible edges are deactivated. However if

a color printout of the drawing is required, it should be displayed with colored areas. The

printout always corresponds to the display on the screen.

Page 101: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 101 / 144

Call function

Once the drawing is in the ideal position on the screen, click the “Plot” button or select “File / Print” from the menu. This opens the Plot window where you can enter all the main print settings.

Select printer

In the Printer/plotter section (1) the required printer should be specified near the field

“Name“. If this field contains the entry “none”, the printer can also be selected from the

Pull-Down-Menu (2).

Paper format: (3) this is where you select the paper format. The size depends on the capabilities of your printer/plotter.

Plot area (4): The pull downlist contains the options view, window, limits.

Display: Selecting this item prints the screen content exactly as displayed.

Window: If this point is selected, you can enter a specific print area (see a later

example).

Limits: With these points the complete drawing is printed. A previously defined zoom is

not considered.

Page 102: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

102 / 144 SelectionProf_Handbook_EN.pdf

Plot scale: (5) This is where you can enter a scale. Once adjusted the drawing fits the page perfectly. You can also select scales, such as 1:2, 1:4 etc.

Plot distance: (6) If the Centre plot option is selected, the position of the drawing on the

paper will be optimised in height and width. An entry in x and y produces a side margin

of the sizes entered.

Preview(7): printout on the paper can be seen beforehand as a preview on the screen.

Page setup (8): the settings can be saved under a name in the plot dialog. Click on the

„add to“button and specify a name.

Page 103: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 103 / 144

Further options

With the button, further options can be opened.

Drawing orientation: (9) specifies the paper orientation.

Options in the shaded display window (10): Here the degree of shading and quality of

the printout can be set.

Shading-Plot: Different shadings can be set here.

Quality: Different quality levels can be set here. The DPI-value can be set using the

”User specific“ option.

Plot style table (11): Different plot styles can be selected here. No modifications should

be attempted here.

Plot options (12): Different options are available here.

Plotting in the background: by activating this, the print request will be executed in the

background.

Plotting with plotting styles: activates the plot style tables.

Plot indications: indications like date, design name etc. are defined here and printed

along with the design.

Page 104: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

104 / 144 SelectionProf_Handbook_EN.pdf

Save changes in the layout: Changes that heve been made are saved in the layout.

Example 1 You want to print the cabinet previously displayed. Go to the File menu and select the Print command. Select the correct printer from the plotter tab. Then return to the plotter settings (2). Select the appropriate paper format, e.g. A4. Select the Display option. (3) Click the Preview button (7). The picture shows the drawing as it will be printed on paper. Exit this window either by right-clicking the mouse and selecting End from the window, or by pressing the Esc key. To print the drawing, click the OK button in the Plot window (12).

Example 2

You can, of course, print individual components as well as whole cabinets. In the

following example we want to print one carcase side panel. Click “Dimension Part” and

mark a carcase side panel with the small box. Now you will see a top view of the

dimensioned side panel. Click “Zoom

Start print control as described in example 1. Select the entry Window from the pull

down list in the plot area section (4). This will take you back to the design window,

where you will see your drawing.

Use the mouse to select a section to be printed. Then move the mouse into the top left

corner of the drawing and left-click.

Then move the mouse to the bottom right corner of the drawing and left-click again.

Subsequently the plot dialog box can be seen. This right corner area is the one, that will

be printed later. The”Window” button can be used to define thus area again.

If you click on button (7) again, you will receive a display of exactly the same area that

you selected before.

You can exit this window by a right click of the mouse and select the entry “end“ in the

window.

To print the drawing, click on “OK“.

Page 105: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 105 / 144

5. Document manager

5.1 Basics

The document manager offers the possibility to cumulatively print the documents for production.

Thereby the appearance and the scope of these production papers can be defined. Alternatively pre-defined guidelines are also readily available.

Following information can be printed:

• Views from the front, top and side, each with or without dimensioning

• 3D exploded drawing or 3D-Perspective view

• All components with absolute dimensioning or chain dimensioning

• Wood cutting lists

• Order list for fittings

5.2 Start Document Manager

At the end of the construction you can start the Document Manager using the „Display the components in a dimensioned format“ link.

You can find this link in the 3D- View of the Designer and in CAD in the Assistant „Display“.

Document Manager Assistant

General

1 Info

2 Back

3 Save

4 Cancel

5 Help

6 Menu

Page 106: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

106 / 144 SelectionProf_Handbook_EN.pdf

5.3 Start Document Manager now

To start document collection output straight away, select one of the pre-defined templates from the list (1) and then click “Save”.

This initiates output, and the document collection is automatically generated.

The document preview opens automatically at the end. If the documents are to be

printed, click on the small printer symbol at the top left of the menu bar.

Click the “X” to close.

5.4 Create new template

To create a new template, enter a new name in field (1) at first, and then click “Save“.

Page 107: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 107 / 144

5.4.1 Sizing views

Subsequently the settings for the first pages would be carried out.

Then with “Save“.

5.4.2 Layout

In the second step, the settings regarding how the 4 cabinet views should be presented, would be adjusted. In any case the type of dimensioning would be adjusted.

Then with “Save“.

1 Definition exploded drawing

2 Definition front view

3 Definition side view

4 Definition top view

1 Page layout

2 Definition of sizing

3 Display help texts. e.g. drilling diameters and depths

Page 108: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

108 / 144 SelectionProf_Handbook_EN.pdf

5.4.3 Page format

In the last step, the formatting of the page would be adjusted.

Then with “Save“.

5.4.4 Export

Subsequently the automatic generation of the document-collection takes place.

5.5 Modify template

In order to change an existing template, select the template to be changed from the List (1) and click on “save“. The subsequent procedures are exactly similar to procedure for creating a new template.

1 Definition page format

2 Definition page size

3 Definition margins

4 Display the position of the component in the carcase by each individual part

5 Number of components per page

Page 109: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 109 / 144

5.6 Delete existing template

To delete a template, select it from the list (1) and then click Delete (2).

5.7 Wood – Bill of Materials

Through the link “Wood – Bill of Materials“ found in the left in the Assistant, a cumulative finished dimensions list of all the used components would be created..

5.8 Hettich Order list

Through the link “Hettich Order list“ found in the left in the Assistant, a cumulative order list of all the used Hettich Fittings would be created.

Page 110: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

110 / 144 SelectionProf_Handbook_EN.pdf

6. Roomplan functions

6.1 Introduction

As a planning tool, Roomplan enables you to display cabinets created using Selection in a room situation. Unlike previous 3-D planning systems, the user is guided through the program by ergonomic Assistants.

Only a limited amount of prior knowledge of CAD is required.

The main functions in Roomplan are:

• Selection of parametric layouts for walls, 3-D generation of various basic configurations with simple walls, L- and U-walls.

• Creation of various window and door elements.

• Adjustment of floors and ceilings.

• Display of various views, isometry and vanishing point.

• Possibility to insert cabinet and decorative elements.

• Creation of work tops, plinth, cornice, front panels and visible sides.

6.2 Starting Roomplan Roomplan is started from the “Selection CAD” program section. From Designer, the

CAD section can be started with the “CAD/Roomplan” Assistant. Use the “Roomplan”

directory tag to call up the Roomplan Assistant.

Always select the “New room plan” function before starting Roomplan; this produces a

blank window.

Page 111: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 111 / 144

6.3 Define wall Start the Define wall function.

The Roomplan Assistant has various options for settings:

1. Definition of the wall type 2. This is where the size reference for the longitudinal details are set:

a) outer side of wall b) middle of wall c) inner side of wall (pre-set)

3. Details of wall height and thickness 4. This is where the wall lengths are given for the respective wall parts. 5. Close wall:

The starting and end points for the wall are automatically connected to close the room. Floor: A floor is put in the room. Ceiling: A ceiling is put in the room.

6. Details of wall and ceiling materials 7. Preview of the selected wall type in the appropriate length.

Page 112: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

112 / 144 SelectionProf_Handbook_EN.pdf

The corresponding surfaces are displayed for material selection.

Wall type “free wall construction”

The wall type "free wall construction" is a special feature. It allows the construction of

free walls with as many wall segments and angles as desired. Because displaying the

wall can become complicated, we advise you change to CAD top view. Select function

“Define wall” and setting “Free wall construction” and proceed as follows:

1. Select .

2. This displays the AutoCAD window. The mouse pointer changes to a small cross.

3. Define the starting point for the first wall. Simply click the mouse anywhere inside

the AutoCAD window (ideally bottom left).

4. There are three ways you can define the wall length and wall end point:

a) Determine the wall end, wall angle and wall length with the mouse. A small

window will appear to help you; in it you can enter the length and angle.

Once you have selected the correct settings, left-click on the mouse

and the wall will be drawn.

b) You can also define the wall length by entering a number in the command line.

For instance, if you enter 2000 then a 2-m long wall will be drawn from the

starting point. The angle is determined by the angle currently set.

c) Drawing lengths and angles in the “right-angled mode”:

If you want the walls to be right-angled, you can set this by pressing F8 on the

keyboard.

Press F8 a second time to deactivate it. Now all you have to do is determine the

direction of the wall in direction x or y, and you can enter the length of the wall

directly. As well as entering wall lengths and directions with the mouse, you can

also enter numbers for exact angles. Using the Orth mode, enter the angle using

a prefixed “<” symbol, e.g. <30. This bends the wall 30 degrees to the previous

wall. You can then also

enter a number to

define the length of

the diagonal wall.

Page 113: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 113 / 144

5. Repeat the procedure with the next wall segment.

It is also possible to incorporate curved walls. To do so, enter the letters “GE” in the

command line and press ENTER to confirm. Then use the mouse to select the middle of

the circular segment and the end point of the circle. If the next wall is to be straight,

enter “LI” for line and press ENTER to confirm.

When you have finished constructing the walls, just press ENTER to end the

construction.

Page 114: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

114 / 144 SelectionProf_Handbook_EN.pdf

6.4 Define windows / doors and openings

For windows, doors and openings, the style is chosen first and then the dimensions and

reference points.

The individual functions are explained here using the doors as an example. They are

the same

for windows and openings.

1) Select the door style (e.g. windows style, opening style)

2) Select the hinged side

3) Sizes: the width and height define the outer dimensions of the door. The door sill

defines the space between the bottom edge of the door and the floor. With double

doors, the details for the hinged side are not taken into account.

4) Doors (windows, openings) can be defined by a space to the reference points (end

wall segment).

5) With the “Position freely” option, the position is chosen freely with the mouse.

6) If an opening angle is entered, the door is shown opened by this angle.

Page 115: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 115 / 144

Positioning the doors, windows, openings

Once the settings have been made, they are confirmed with the green tick. The AutoCAD window appears. Select a wall into which you want to put a door (or window, opening). You must get it right on the line for the wall in question. Depending on whether you click closer to the left or right corner of the wall, the reference point will be seen from this end.

6.5 Modifying windows / doors / openings

If you want to make changes to any doors, windows or openings that have already been

entered, do so with the “Change windows, doors and openings” function.

Proceed as follows:

1) Once you have chosen the function, highlight the door / window / opening in

question. You must click on one of this object’s lines.

2) This opens the relevant Assistant (door/window/opening). Make your changes and

confirm them with the green tick.

6.6 Deleting windows / doors / openings

Windows, doors and openings can be deleted with the “Delete part” icon on the

functions bar.

Select the “Delete part” icon and then click on the components concerned (window etc.).

Press ENTER to confirm the deletion.

Page 116: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

116 / 144 SelectionProf_Handbook_EN.pdf

6.7 Change the wall characteristics

With the function “change the wall characteristics”, the height, thickness, material and alignment of the cabinet wall can be changed. After the function is clicked the cursor becomes a small square. With this square, a line of the concerned wall is clicked. The wall will be displayed as a dotted line. Here multiple walls can also be accessed one after the other.

After all the walls to be changed are selected, this selection must be confirmed with a right mouse click or with the Enter key on the keyboard. The dialog “edit wall“ is opened.

The settings will be saved by clicking on the green tick and wall characteristics are changed.

If the walls require further changes, the command “edit wall” should be accessed afresh.

1 Changes the wall height

2 Changes the wall thickness

3 Changes the material of the wall

4 Changes the alignment of the wall

Page 117: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 117 / 144

6.8 Insert furniture or accessories

6.8.1 Select cabinet

You can incorporate the cabinets created in SelectionProfessional with function item "5.

Insert furniture and decorational elements”. You can also access a library that already

contains a number of standard cabinets.

Selecting this function opens a window. Select the appropriate drawing. When you

highlight a file name the corresponding view of the cabinet in question is displayed.

Select “Open” to load the selected cabinet.

6.8.2 Add furniture to a wall

Once you have selected a cabinet from the library, the mouse pointer changes to a

small square. Now click on the wall where you wish to stand the furniture. It is important

that you click exactly on the wall line. Once you have selected the wall, the carcase is

automatically orientated along it. Inserting and positioning cabinets is explained more

clearly by the following graphic.

The insertion point of the cabinet is defined by clicking on the grey buttons on the outer

corners of the displayed cube.

The current insertion point is shown in red. The insertion points need to be changed if,

for instance, you want to put the bottom right corner of a cabinet in the corner of the

room.

Current insertion point of the cabinet (here e.g. bottom /right)

Page 118: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

118 / 144 SelectionProf_Handbook_EN.pdf

In this case, we want the insertion point to be the back bottom right corner of the

cabinet.

Select this button. The red colour now indicates that it is active.

The cabinet is shown as a cube before it is put in its final position, and you can move it along the walls as you wish. Depending on the wall orientation, the cabinet will always adapt to the course of the wall.Seen from the top, the cabinet can now be pushed into the corner of the wall.

When the left mouse is clicked, it will be moved

here.

To move a cabinet out of the corner for a blend

bar, a value can be entered in the field “Distance

2“. In our example it is “-50mm“, to move the

cabinet to the left.

6.8.3 Inserting furniture in an existing object (fu rniture or decorative object)

If a cabinet has already been inserted, then it can be used as a reference object for an additional planned cabinet. The object can then be inserted anywhere to the right/left/front/back, top or bottom of the existing object.

Page 119: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 119 / 144

Procedure Select an additional cabinet using the “Insert furniture and decorational elements” function. Click on the previously inserted cabinet to open a new window.

Use the grey alignment quadrats (1) to

determine the position of the new cabinet in

relation to the existing one.

Click on the alignment quadrat to insert the

cabinet correspondingly to the right, left, front,

rear, bottom or top.

“Gap1 (2)“ defines the gap to the existing

cabinet.

Repeat inserted item (3) permits direct insertion

of the same cabinet against an existing one.

Planning furniture with different depths (front or

back-flush)

If, for instance, a wall unit is being fitted, it can be orientated to the tall unit. Procedure:

1. Insert tall unit in Roomplan

2. Select wall unit

3. Select tall unit as reference point

4. Change tab (see illustration left)

5. Drag cabinet to top (1) and rear (2) on the grey quadrat.

6. Select green tick. Cupboard is inserted.

Page 120: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

120 / 144 SelectionProf_Handbook_EN.pdf

Rotate cabinet

The third tap enables selection of tilt

function.

First the corresponding axis of rotation is

selected and then the angle of rotation is

adjusted. This is carried out by specifying

the angle or by mouse selection after

unblocking the lock.

Page 121: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 121 / 144

6.9 Delete item

Select the Delete item icon in the Selection Button bar. Then select the cupboard or object you wish to delete.

6.10 Move / rotate item

If you want to move a cupboard or other object, select the Move item icon from the Selection Button bar. Then left-click on the object to select it, define the base point on the object you want to move, and move it to the desired position. If you want to rotate a cupboard or an object, select the Rotate item icon from the menu. Then select the object you wish to rotate. Determine the position of the rotation point and enter the rotation angle. You can do this either by moving the mouse or by entering the rotation angle (+ left, - right)

6.11 Select and insert decorative elements

In order to display the room situation as realistically as possible, the system already contains a number of furnishing elements that can be included in the plan. Activate the Insert furniture and decorational elements option from the Deko folder. This folder contains a variety of subdirectories for various furnishing areas. Select the desired decorative element. The AutoCAD main window appears, and the mouse pointer changes to a small square. You can now select a wall, a cupboard or the floor to position the decorative element on or against. Decorative elements can be inserted in exactly the same way as cupboards.

Page 122: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

122 / 144 SelectionProf_Handbook_EN.pdf

Example: Inserting a sink unit

In the following example it is displayed how a sink unit can be inserted in a kitchen

counter. The kitchen counter has already been created and the sink unit should be fitted

over the second cabinet from the left.

Now the sink unit would be selected using “Insert furniture or design elements” and the

second cabinet from left is selected as the reference object.

Subsequently the alignment square for the top is selected in the dialog “insert article”

and the thickness of the work top (38mm) is entered in the field “Distance1“.

Page 123: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 123 / 144

To get a preview on the CAD-window, the enter key must be pressed after the entry of

distance 1. Then the settings will be displayed in the CAD window. If the settings are

correct they must be saved with the green tick. Subsequently the sink unit will be

inserted.

Page 124: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

124 / 144 SelectionProf_Handbook_EN.pdf

6.12 Definition of raster

Raster is used to bring the cabinets to a definite height dimension. This is essential

during the use of plinths in room planning. Top cabinets can be brought to the correct

height dimension with the help of raster.

When should a raster be defined?

Raster need not be always defined. If a cabinet is already furnished with a plinth, it can

be directly positioned on the base of the room planning.

Raster should always be defined for cabinets with levelling feet. Since the levelling feet

may possess a range of adjustment, otherwise an exact height can never be defined.

Cabinet with fixed plinths without

height raster specification

Cabinet with plinths without

height raster specification. Centre

of reference is the bottom panel.

Cabinet with levelling feet and

specified height raster for e.g.

110mm (desired plinth height)

Page 125: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 125 / 144

Definition of raster

Raster can be accessed from room planning Assistant. Values can be specified with the

”Define raster“ function.

Name Any name can be used for indicating the raster. A double click in the

field can be used to change the name.

Height The corresponding height of raster can be specified here. The height

is always calculated from the base (0mm).

Activates or deactivates raster

Planning reference of raster

Up arrow indicates that all inserted cabinets seen from height raster

will be inserted towards the top. Down arrow means that the cabinets

will be inserted towards the bottom.

Inserts a new raster

Deletes an existing raster

If values and settings are changed, they should be saved on the

diskette.

Page 126: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

126 / 144 SelectionProf_Handbook_EN.pdf

Raster as width raster

Raster can also be used as width raster. This enables cabinets to be placed exactly along the width of a wall.

Corner distance Specifies the corner distance from wall end.

Depth Defines the depth of raster in the room

Sub divisions Defines the number of sub divisions to be made on the wall segment

Equal distances The sub divisions are made at equal distance

Linear division

The sub divisions can be defined freely

Eg. 400mm:200mm:400mm:1

Use of raster

If raster has been defined, it can be activated or deactivated with the “Show/hide

raster“function of the Assistant.

If only a height raster is active, it is immediately used during insertion of a cabinet. For

e.g. if the raster “A1“with a height of 110 is activated and then a bottom panel is

inserted, the cabinet is placed at a height of exactly 110 mm height in relation to the

bottom panel. If several rasters are defined, one raster should be selected as reference.

This is significant only in the perspective of the room.

Page 127: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 127 / 144

6.13 Roof pitch definition

6.13.1 Insert roof elements

With the “insert roof elements“ function, the roof elements of the room setting are added. The insertion of room elements is best possible in the top view.

After accessing the function, knee tile height, room height and roof incline values should be specified.

Here the roof incline should be specified according to the knee tile height and the room height, otherwise the value would be overwritten. After the settings have been entered, they are confirmed with the help of the green check mark.

The AutoCAD window reappears. The wall adjacent to the roof pitch should be selected. For this the line of the corresponding wall should be clicked exactly with the help of the small box.

The roof direction should be specified next. The mouse is clicked in the room, to specify the direction of the roof ridge.

The “insert roof elements“function should be executed again to specify further roof elements, Only a single roof element can be specified at a time.

Page 128: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

128 / 144 SelectionProf_Handbook_EN.pdf

6.13.2 Alignment of walls to the roof

With the “Align walls to roof“function, walls can be compressed on the inserted roof elements.

All walls adjoining the roof should be selected on accessing this function. The selection is confirmed with a right mouse click or the Enter key.

Subsequently the corresponding roof element should be selected.

Now the walls are aligned to the roof pitch.

Page 129: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 129 / 144

6.13.3 Blending roof elements

With the “Blending roof elements“function, the individual roof elements are blended with each other. When two roof pitches overlap each other, the overlappings should be removed. For this purpose the respective roof elements are blended with each other, this means that the roof elements are joined with each other and the projections are removed.

After accessing this function the roof elements that are to be aligned should be clicked one after the other.

If further roof elements are to be blended with each other, this function should be executed one more time.

TIP: Blending ensures that several roof elements are connected to a single roof element. Hence it becomes meaningful to connect all the roof elements first and then align the walls to the roof.

6.14 Component functions

Work tops and plinths can be used in the Designer during cabinet design itself. They refer only to one cabinet design at a time. If plinths and work tops are designed for several cabinets, the work and plinth function should be selected from the room planning. This considers several cabinets for designing plinth and work tops.

6.14.1 Work top functions

Selection procedure

Work tops can be inserted on preferred cabinets. This can be carried out for one cabinet or more simultaneously. If several cabinets are selected, it is important to consider, that all cabinets close equally and no cabinet is taller than the rest.

The best method is to select the cabinets one after the other in a sequence. For a right angled cabinet assembly, only the first and the last cabinet can be selected. The work tops are automatically designed for all cabinets. Exactly one line of the cabinet should be selected, preferably the cabinet side.

If the cabinet assembly is not right angled, each cabinet must be selected individually.

Page 130: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

130 / 144 SelectionProf_Handbook_EN.pdf

Right angles cabinet assembly

Select first (1) + last cabinet (2)

Non right angled cabinet assembly (Ex. 45° corner cabinet). Each cabinet should be mounted individually. Beginning with the first (1), then the second (2) until the last cabinet (4), the cabinets are selected in a sequence.

Work top settings

Protrusion front

Work top protrusion in the front in relation to the cabinet side

Protrusion rear

Work top protrusion rear

Protrusion right

Work top protrusion right

Protrusion left

Work top protrusion left

Connect segments Change the contour from the worktop from one edge to the other. Press the >> symbol

Page 131: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 131 / 144

and select both edges one after the other. The edges will be joined together.

Height offset

Distance from plate to cabinet. Is normally 0. The function can be used to create a wall shelf and to let a work top hover over the actual cabinets.

Component thickness

Work top thickness

After specifying the values the function can be closed with the green check mark and the work tops can be assembled.

Cutting work tops (with recommendation)

Work tops can be cut. This is required if the workplates are not linear. It is possible that a value is recommended. The “Cut work top“function is used for this purpose. Exactly

one line of the work top is selected. Different recommendations are indicated depending on the work top model. This is best seen in the top view.

The red line is selected and the work top is cut at the corresponding point. The entire procedure is confirmed with the green check mark.

Work tops can be deleted or removed with the normal item .

Page 132: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

132 / 144 SelectionProf_Handbook_EN.pdf

Cut work tops (from point to point)

Recommendations for cutting were automatically implemented in the aforementioned example. It is also possible that a work top needs to be cut individually. The function“Cut work top (from point to point) “ is accessed from the Assistant.

The edge of the work top is selected. The starting point of the cross cut is selected (1) and then the second (2). Both the points are connected by a cut line and the work top is correspondingly cut.

Isolate/show elements

Sometimes it is difficult to select the cutting recommendations exactly or define them exactly during manual cutting. This can be eased by isolating components. Only the isolated component is displayed and the remaining components are hidden. All actions like cutting work tops can be carried out now. This is also helpful for other functions like manual dimensioning etc.

”Show elements“function shows the elements again.

All elements shown Isolated work top

Page 133: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 133 / 144

6.14.2 Plinth functions

Selection procedure

The plinth function is configured in a manner similar to the work top function. The cabinets, which need a plinth, are selected. In order to design plinths simultaneously for several cabinets, the bottom panels of all the cabinets should be of equal height.

The selection principle is analogous to the work top; the first and the last cabinets are selected and the plinth follows the cabinet contour automatically. If a cabinet is not right angled, the cabinets should be individually selected.

Plinth settings

Indent dimension front

Indent dimension front of the plinth in relation to the cabinet front edge. The standard 50 is optimally aligned on the leveling feet.

Indent dimension rear

Indent dimension plinth rear

Indent dimension right

Indent dimension plinth right

Indent dimension left

Indent dimension plinth left

Height

Plinth height. This should match with the raster height settings.

Rail The plinth can be placed around the four sides of the cabinets. With the “Rail“function the plinth rails can be set to front/rear/right/left.

Height offset

Plinth distance to lower edge of cabinet

Page 134: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

134 / 144 SelectionProf_Handbook_EN.pdf

Component thickness

Plinth thickness

After the selection of the settings, the erection of the plinth is confirmed with the green check mark.

6.14.3 Cornice functions

Selection procedure

Cornices can be set up with tall units and top units. Each individual cabinet should be selected one after the other. The cornices will automatically follow the cabinet contours and be cut on mitre.

Page 135: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 135 / 144

The tall and top units are selected from 1-3 The cornices follow the cabinet contours.

Cornice settings

Protrusion front

Cornice protrusion front w.r.t. cabinet side

Protrusion rear

Cornice protrusion rear

Protrusion right

Cornice protrusion right

Protrusion left

Cornice protrusion left

Height

Height/depth of cornice

Rail Cornices can be set on all 4 sides of the cabinet. With the “Rail“ function , the cornice can be set to front/rear/ right/left.

Height offset

Cornice distance to top edge of cabinet

Component thickness

Thickness of the cornice

After the selection of the settings, the erection of the cornice is confirmed with the green check mark.

Page 136: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

136 / 144 SelectionProf_Handbook_EN.pdf

6.14.4 Front panel functions

Selection procedure

Front panels can be fixed on the cabinets at required areas. In case of a tall unit, it can be fixed both sideways as well as on the top (top filler panel).

If a tall unit needs to be fitted with a front oanel, it must be selected in the 3D view. It should be selected exactly on the cabinet side edge (preferably outside).

The cabinet edge should be selected exactly.

Side is selected

Front panel is placed laterally

Select top panel, front panel is placed on top

Page 137: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 137 / 144

Front panel settings

Component height

Specifies height/width of the front panel

Component height Component height/width can also be determined with the mouse. A point, on which the component is attached, is selected.

Indent

Specifies the indent dimension of the front panel.

Protrusion front

Specifies protrusion front/top

Protrusion rear

Specifies protrusion rear/bottom

Front panel thickness

Specifies front panel thickness

After the selection of the settings, the erection of the front panel is confirmed with the green check mark.

6.14.5 Visible sides functions

Selection procedure

The screen function can be used to replicate a certain component, e.g. a cabinet wall. Subsequently the newly formed component can be modified.

For the visible side of base cabinet the outer cabinet wall is selected and then replicated. Protrusions can be specified thereafter.

Page 138: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

138 / 144 SelectionProf_Handbook_EN.pdf

Front panel settings

Protrusion front

Protrusion of the front visible sides w.r.t. side panel

Protrusion rear

Protrusion of the rear visible sides w.r.t. side panel

Protrusion top

Protrusion of the front visible sides w.r.t. side panel

Protrusion bottom

Protrusion of the visible sides w.r.t. side panel

After the selection of the settings, the erection of the visible sides is confirmed with the green check mark.

Selection of the cabinet edge Side panel is double profiled.

Page 139: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 139 / 144

6.15 Material

6.15.1 Material selectionl

Fundamentals

Different materials and surfaces can be assigned to each cabinet and component (plinth, work tops) in CAD.

They can also be displayed in colour and released in the bill of goods.

Material settings

The Assistant “Surfaces and material“can be started with the “Material“tab. The selection can be done with “Material selection“.

Process of material selection:

1. Furniture or components, for which a material or surface should be assigned. 2. Select material category. 3. Select element for material allocation 4. Select surface 5. Determine grain direction

1) Cabinet selection One or more cabinets, which need to be coated with the surface, can be selected. The corresponding cabinet is selected with a cabinet edge. 2) Component selection An individual component is selected here, e.g. plinth, visible side or work top. Likewise, a single door or drawer for a front panel can also be selected. An individual side panel can also be selected. 3) Surface preview Displays the selected surfaces on the cabinet 4) Category The material category is selected here. This in turn influences the surface selection options. 5) Element selection The elements of a cabinet, which influence surface selection, are selected here. 6) Surface selection The desired surface is selected here.

Page 140: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

140 / 144 SelectionProf_Handbook_EN.pdf

Sample cabinet

Selection:

- Work top beech, grain long

- Left cabinet front beech, grain long

- Right cabinet, front beech light, grain diagonal

- Drawer front centre, colored red for component selection

- Visible sides, colored red for component selection

Page 141: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 141 / 144

6.15.2 Color display of room / cabinet

Displays the cabinet in the selected surface.

Different settings can be undertaken in the dialog window.

Quality There are 3 quality levels

High / medium / outline

The setting influences the display speed and quality.

Render target Specifies the display position of furniture / room layout

Display window > In the actual window Render window > Own window

Using the render window permits the saving of the displayed situation in different formats.

Illumination Brightness specification, optimal values lie in the 90-100 range.

Values can be set individually. By clicking near the value, further settings can be specified.

Brightness Brightness setting for the display

Contrast Display contrast settings

Centre tone With the setting

Outside light The value of this field should always be set to OFF

Edit background Off = background is white

On= standard background

Lights Lights should be set to “On“.

Page 142: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

142 / 144 SelectionProf_Handbook_EN.pdf

6.15.3 Concealed display / Light symbols

Hidden display ON Hidden display OFF

Light symbols ON Light symbols OFF

Displays the position of the light source. The light sources are automatically placed

according to the room size. They can be manually shifted to achieve a special light

effect. It is best to move the light symbol in the top view and only in the vertical and

horizontal position. The AutoCAD function F8 helps in achieving this movement. The

light symbol can be moved in a straight direction only.

Page 143: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

SelectionProf_Handbook_EN.pdf 143 / 144

6.16 Output

6.16.1 Wood- Bill of Materials

A detailled description of the function “Wood– Bill of Materials“ in Section 3.8.1.

6.16.2 Hettich order list

A detailled description of the function “Hettich Order list“ in Section 3.8.2.

6.16.3 Document manager

All components are dimensioned and displayed

This function is identical to the function “All components are dimensioned and displayed“ in Designer. A detailled description in section 5 “Document manager“.

Carcase overview in the room

Through the link “carcase overview in room“, an overview of all the cabinets which are used incl.the overview of the components which are to be added to the room planning would be created.

Wood bill of items (Complete room)

Through the link “Wood Bill of Materials(Complete Room)“ found in the left in the Assistant, a cumulative finished dimension list of all the components which are used in the current room plan is created. Hereby all the cabinets which are used would be considered together.

Wood bill of items (Individual cabinet)

Through the link “Wood Bill of Materials (individual cabinet)“ found in the left in the Assistant, a cabinet based finished dimension list would be created. Hereby each cabinet of the current room plan would be considered individually...

Hettich order list (Complete room)

Through the link “Hettich Order list (complete room)“ found in the left in the Assistant , a cumulative order list of all the Hettich fittings used in the current room plan would be created. Hereby all the cabinets which are used would be considered together.

Page 144: SelectionProf Handbook EN - Hettich · SelectionProfessional from Hettich FurnTech assists you in every step in this process. The program provides the documentation required for successful

Handbook SelectionProfessional

144 / 144 SelectionProf_Handbook_EN.pdf

Hettich order list (Individual cabinet)

Through the link “Hettich Order list (individual cabinet)“ found in the left in the Assistant, a cabinet based order list of the Hettich fittings which are used would be created. Hereby each cabinet of the current room plan would be considered individually.

6.17 Examples

A comprehensive example is available in the document SelectionProf_Training

exercises_EN.PDF.