AC CURRENT SWITCH MODEL : DCS-030/ DCS-150 / DCS-250 (DCS ...
Section of hip fixation plate - TIPSAN TIBBI ALETLER · DCS Plate 95º DCS Platte 95º Plaques de...
7
DHS Plate 135º DHS Platte 135º Plaque de DHS 135º Indication : The compression hip plate is primarly indicated for intertrochanteric fractures. However, it can be also find applications in selected sub-trochanteric fractures, mid cervical and low sub-capital fractures of the femoral neck. A com;lete range of angled plate is available from 130º to 150º in 5º increments. They are used in conjuction with large diameter sliding lag screws. The lag screws have a coarse buttress thread to provide secure fixation in the femoral head. The shaft of the lag screw is machined on two opposing sides to correspond to the internal flats of the plate barrel preventing rotation of the lag. The barrel of the plate is available in two lenghts, 38 mm for normal adult use and 25 mm for smaller adult pediatric surgery (special request). If needed, added compression can be applied to the fractures site by means of the compression screws. Plate details : Designed for maximum strenght from one piece, forged. Plate thickness : 5.6 mm Plate width : 18.0 mm Hole spacing : 16.0 mm Screws to be used : All holes accept diam. 4.5 mm cortical screws. End of holes also accept diam. 6.5 mm cancellous screws. All plates are slotted to accept a tension device. Material : Certified Stainless Steel according to ASTM F.138 - ISO 5832/1. Section of hip fixation plate compression system Holes Ref. Number Titanium Length mm Ref. Number Stainless Steel 135º 10402002002 10402002003 10402002004 10402002005 10402002006 10402002007 10402002008 10402001001 10402001002 10402001003 10402001004 10402001005 10402001006 10402001007 10402001008 10402001009 10402001010 10402001011 10402001012 10402001013 10402001014 10402001015 10402041004 10402041005 10402041007 10402041008 10402041010 10402011003 10402011004 10402011005 130º 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4 5 7 8 10 4 5 6 50 66 82 98 114 130 146 162 178 194 210 226 242 258 274 82 98 130 146 178 82 98 114 140º E-10
Transcript of Section of hip fixation plate - TIPSAN TIBBI ALETLER · DCS Plate 95º DCS Platte 95º Plaques de...
DHS Plate 135º
DHS Platte 135º
Plaque de DHS 135º
Indication : The compression hip plate is primarly indicated forintertrochanteric fractures. However, it can be also find applicationsin selected sub-trochanteric fractures, mid cervical and low sub-capitalfractures of the femoral neck. A com;lete range of angled plate isavailable from 130º to 150º in 5º increments. They are used inconjuction with large diameter sliding lag screws. The lag screwshave a coarse buttress thread to provide secure fixation in the femoralhead. The shaft of the lag screw is machined on two opposing sidesto correspond to the internal flats of the plate barrel preventing rotationof the lag. The barrel of the plate is available in two lenghts, 38 mmfor normal adult use and 25 mm for smaller adult pediatric surgery(special request). If needed, added compression can be applied tothe fractures site by means of the compression screws.
Plate details : Designed for maximum strenght from one piece, forged.
Plate thickness : 5.6 mmPlate width : 18.0 mmHole spacing : 16.0 mmScrews to be used : All holes acceptdiam. 4.5 mm cortical screws. End ofholes also accept diam. 6.5 mmcancellous screws. All plates areslotted to accept a tension device.Material : C e r t i f i e dStainless Steel according to ASTMF.138 - ISO 5832/1.
Section of hip fixation platecompression system
HolesRef. NumberTitanium
Lengthmm
Ref. NumberStainless Steel
135º
10402002002104020020031040200200410402002005104020020061040200200710402002008
104020010011040200100210402001003104020010041040200100510402001006104020010071040200100810402001009104020010101040200101110402001012104020010131040200101410402001015
1040204100410402041005104020410071040204100810402041010
104020110031040201100410402011005
130º
23456789
10111213141516
4578
10
456
50668298
114130146162178194210226242258274
8298
130146178
8298
114
140º
E-10
DCS Plate 95º
DCS Platte 95º
Plaques de DCS 95º
Indication : Condylar plate is indicated primarly for the fixation ofsupracondylar fractures and for intercondylar. T and Y fractures.There are certain occasion when a proximal femoral fractures maybe treaded with the sliding condylar screw, such as a complex proximalspiral fracture.
Plate details : Designed for maximum strenght from one piece, forged.
Plate thickness : 6.5 mmPlate width : 16.0 mmHole spacing : 16.0 mmScrews to be used : All holes accept diam. 4.5 mm cortical screws.End of holes also accept diam. 6.5 mm cancellous screws. All platesare slotted to accept a tension device.
Material : Certified Stainless Steel according to ASTMF.138 - ISO 5832/1.
Section of hip fixation platecompression system
HolesRef. NumberStainless Steel
10403001001104030010021040300100310403001004104030010051040300100610403001007104030010081040300100910403001010104030010111040300101210403001013
23456789
1011121314
Lengthmm
44607692
108124140156172188204220236
E-11
DHS/DCS Lag Screw
Indication : To be used in case of intracapsular and intercervicalfractures, and some types of interochanteric fractures. Cannulatedto receive the guide wires with a slot to make rotation impossible.Partially threaded heavy duty lag screw for use with DHS and DCSplates. Buttress thread from provides enhanced pull-out resistancein cancellous bone. Opposing flats along shark engage with machinedflats within plate barrel to prevent rotation. Tappered tip permitseasier insertion. Thread diameter 12.5 mm, thread length 22 mm.
Material : Certified Stainless Steel according to ASTMF.138 - ISO 5832/1.
Section of hip fixation platecompression system
Indication : P r o v i d e s m e c h a n i c a lcompression at the fracture site when used inconjuction with DHS and DCS compressionlag screws. It is socket head screws.
Material : Certified Stainless Steelaccording to ASTM F.138 - ISO 5832/1.
Lengthmm
Ref. NumberTitanium
1080114200110801142002108011420031080114200410801142005108011420061080114200710801142008108011420091080114201010801142011108011420121080114201310801142014108011420151080114201610801142017
50556065707580859095
100105110115120125130
Ref. NumberStainless Steel
1080114100110801141002108011410031080114100410801141005108011410061080114100710801141008108011410091080114101010801141011108011410121080114101310801141014108011410151080114101610801141017
Lengthmm
Ref. NumberTitanium
10808052001 31
Ref. NumberStainless Steel
10808051001
DHS/DCS Compression Screw
E-12
DHS / DCS Plate CompleteImplant Set
Description DescriptionRef.Number PiecesRef.Number Pieces
1080114100110801141002108011410031080114100410801141005108011410061080114100710801141008108011410091080114101010801141011
11111111111
1040200100210402001003104020010041040200100510402001006104020010071040300100310403001005104030010071040300101010403001012
11111111111
DHS / DCS Lag Screw Complete 50 mmDHS / DCS Lag Screw Complete 55 mmDHS / DCS Lag Screw Complete 60 mmDHS / DCS Lag Screw Complete 65 mmDHS / DCS Lag Screw Complete 70 mmDHS / DCS Lag Screw Complete 75 mmDHS / DCS Lag Screw Complete 80 mmDHS / DCS Lag Screw Complete 85 mmDHS / DCS Lag Screw Complete 90 mmDHS / DCS Lag Screw Complete 95 mmDHS / DCS Lag Screw Complete 100 mm
DHS Plate 135º 3 HolesDHS Plate 135º 4 HolesDHS Plate 135º 5 HolesDHS Plate 135º 6 HolesDHS Plate 135º 7 HolesDHS Plate 135º 8 HolesDCS Plate 95º 4 HolesDCS Plate 95º 6 HolesDCS Plate 95º 8 HolesDCS Plate 95º 11 HolesDCS Plate 95º 13 Holes
Ref. Number : 18005020055
E-13
DHS / DCS Plate CompleteInstrumentation Set
Ref. Number : 18005020051
Description DescriptionRef.Number PiecesRef.Number Pieces
1060612501110601071001106010750111060107100410601071003106080610021060806113510608061095
221111111
108070911021080703120110608061001106100510011061005100210601071002106070810011060407100110606121001
11111111
Centering Sleeve for TapWrench ScrewsGuide Sleeve LongCoupling Screw for RemovelGuide ShaftMeasuring Gauge for Guide WireAngled Guide for DHSAngled Guide for DCS
Calib. Threaded Kirschner Wire 2.5x230 mmTrocar Kirschner Wire 2.0x230 mmDrill Guide for DHSDCS Triple ReamerDHS Triple ReamerCoupling ScrewImpactorT-Handle with ChuckTap
E-14
Ref. Number10601071002
Ref. Number10608061001
Wrench Screw Guide Sleeve Long
Ref. Number10601075011
Ref. Number10601071001
Ref. Number10807031201
Drill Guide for DHSCoupling Screw
Trocar Kirschner WireØ 2.0 x 230 mm
Ref. Number10604071001
Ref. Number10607081001
Impactor
T-Handle with Chuck
Guide Sleeve Long Complete View
Angled Guide for DHS 135º
Ref. Number10608061135
E-15
Tap Guide Sleeve Short
Ref. Number10606125011
Ref. Number10606121001
Ref. Number10610051002
DHS Triple ReamerDCS Triple Reamer
Ref. Number10610051001
Angled Guide for DCS 95º
Ref. Number10608061095
Ref. Number10601071004
Ref. Number10601071003
Guide PinØ 2.5 x 230 mm
Ref. Number10807091102
Measuring Device
Ref. Number10608061002
Guide Sleeve Short Complete View
Coupling Screw Guide Shaft
Complete View
Complete View
E-16
