WARNING: Replace your current arm assembly with this new redesigned arm immediately. The nut securing the television to the existing arm assembly can loosen, causing the television to detach from the arm assembly. This can pose an impact hazard, resulting in injuries.

3/16 in.

1/4-20 x 3/8 in.1/4-20 x 3/4 in.

Kit Includes:

Hex Key(Allen wrench)

Product Label

Cable Tie

SLF7 Arm Replacement

If you have any questions or concerns, just give us a call at 1-877-277-3707.

We’re ready to help!

DISCONNECT CABLES:

Disconnect all cables from your TV.

IMPORTANT! Have someone hold the TV while performing this entire removal procedure.

UNLOCK THE TV:

Remove the locking screw using 3/16 in. hex key (Allen wrench) 04 and discard.

Note: Removal of this screw alone will not completely detach TV from mount.

REMOVE THE TV:

HEAVY! Use two people to remove the TV. With your helper, first swing the bottom away from the arm, then lift the TV off the mount.

1

3

2

HEAVY! Use two people to remove the TV.

Locking Screw

TV / TV Bracket ArmArm TV / TV Bracket

2

1

SECTION A REMOVE YOUR TV FROM THE ARM ASSEMBLY

3/16 in. Hex Key(Allen wrench) 04

x101

Arm Assembly

02x1

Locking ScrewWall Plate Screws

03x4

05x1

06 x4

04 x1

6903

-002

048

00

DISCONNECT CABLES:

Remove the cable cover and any cable ties holding the cables onto to the arm.Save the cable cover for STEP 13.

REMOVE COVER PLATES:

Remove the two cover plates from the wall plate by pulling the middle to bow the ends out of the channels.Save the cover plates for STEP 14.

UNLOCK ARM ASSEMBLY:

To release the arm assembly from the wall plate, remove the four wall plate screws using 3/16 in. hex key (Allen wrench) 04 , then discard the screws.

REMOVE ARM ASSEMBLY (and DISCARD):

Remove the arm assembly from the wall plate by:1. Swing the bottom of the arm assembly out.2. Lower the arm assembly out of the wall plate channel.Discard this arm assembly.

4

6

5

7

Cable Cover

Arm

Cable Ties

Cover Plate

Cover Plate

Wall Plate

Wall Plate Screw

Arm Assembly Arm Assembly

Wall Plate

Wall Plate

Wall PlateChannel

1

2

SECTION B REMOVE THE ARM ASSEMBLY FROM THE WALL PLATE

3/16 in. Hex Key(Allen wrench) 04

2

8

1

2

SECURE ARM ASSEMBLY:

Secure using four new wall plate screws 03 with 3/16 in. hex key (Allen wrench) 04 .

CAUTION: Important: To avoid potential personal injury or property damage! The wall plate screws 03 must be installed to secure the arm assembly 01 to the wall plate.

INSTALL NEW ARM ASSEMBLY:

Install the arm assembly 01 onto the wall plate by:

1. Tilting the arm assembly 01 and tucking it under the wall plate channel lip as shown.

2. Rotating the bottom inward to rest on the wall plate.

NOTE: Position the arm assembly 01 into the previous arm location, or left or right as desired.

9 Wall Plate Screw 03

Arm Assembly 01Arm Assembly 01

Wall Plate

Wall Plate

Wall PlateChannel

3/16 in. Hex Key(Allen wrench) 04

SECTION C INSTALL THE NEW ARM ASSEMBLY

SECTION D INSTALL THE TV

Continue on PAGE 4

3

INSTALL PRODUCT LABEL:

Adhere the new SLF7 product label 05 OVER the existing SLF5 label on your wall plate.

10

Product Label 05

Wall Plate

Once the wall plate screws 03 are in place, your new arm assembly is secured and ready to install your TV.

ATTACH CABLES:

Use cable ties 06 to secure your cables to arm assembly 01 .

IMPORTANT: Fully extend arm 01 to ensure you have enough slack in the cables during normal operation.

Install the cable cover (from STEP 4) over the cables.

SECURE THE TV:

Lock the TV to the arm assembly 01 with the locking screw 02 using 3/16 in. hex key (Allen wrench) 04 .

CAUTION: Avoid potential personal injury or property damage! This locking screw must be installed to secure the TV onto the arm assembly 01 .

13

1211

INSTALL COVER PLATES:

Bow the middle of each cover plate outward to slip the ends into the channels of the wall plate.

NOTE: The 3/16 in. hex key (Allen wrench) 04 can be stored behind the upper cover plate.

14

Cover Plate

Cover Plate

Arm Assembly 01

Wall Plate

Arm Assembly 01

Cable Cover

Cable Ties 06

4

3/16 in. Hex Key(Allen wrench) 04

3/16 in. Hex Key(Allen wrench) 04

Locking Screw 02

HANG THE TV:

HEAVY! Use two people to hang the TV.

With your helper, first hook the hanging tab onto the arm assembly 01 , then rest the TV into place.

HEAVY! Use two people to hang the TV.

Hanging Tab

Arm Assembly 011

2

Your assembly is now complete and your TV is secure.